Honeywell 2000 Installation, Operation and Maintenance Manual

HercuLine

®

2000 Series Actuator

Installation, Operation and

Maintenance Manual

Honeywell Field Solutions

Notices and Trademarks

Copyright 2008 by Honeywell

Revision 7 July 2008

Warranty/Remedy

Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship. Contact your local sales office for warranty information. If warranted goods are returned to Honeywell during the period of coverage, Honeywell will repair or replace without charge those items it finds defective. The foregoing is Buyer's sole remedy and is in lieu of all other warranties, expressed or implied, including those of merchantability and fitness for a particular purpose. Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use.

While we provide application assistance personally, through our literature and the Honeywell web site, it is up to the customer to determine the suitability of the product in the application.

CE Conformity

This product conforms with the protection requirements of the following European Council Directive: 89/336/EEC, the EMC directive and 73/23/EEC, the Low Voltage Directive. Conformance of this product with any other “CE Mark”

Directive(s) shall not be assumed.

Attention

The emission limits of EN 50081-2 are designed to provide reasonable protection against harmful interference when this equipment is operated in an industrial environment. Operation of this equipment in a residential area may cause harmful interference. This equipment generates, uses, and can radiate radio frequency energy and may cause interference to radio and television reception when the equipment is used closer than 30 m to the antenna(e). In special cases, when highly susceptible apparatus is used in close proximity, the user may have to employ additional mitigating measures to further reduce the electromagnetic emissions of this equipment.

Honeywell Process Solutions

512 Virginia Drive

Fort Washington, PA 19034

HercuLink

®

and HercuLine

®

are trademarks of Honeywell

Palm is a trademark of Palm Inc.

Other brand or product names are trademarks of their respective owners. ii HercuLine™ 2000 Series Actuator - Installation, Operation and Maintenance Manual Revision 7

7/08

About This Document

Abstract

This manual describes the installation, set up, operation, maintenance, and troubleshooting of the

HercuLine 2000 series actuators.

References

The following list identifies all documents that may be sources of reference for material discussed in this publication.

Document Title Doc ID

HercuLine 2000 Series Actuator Specification

HercuLine 2000 Series Actuator Model Selection Guide

Modbus

®

RTU Serial Communications User Manual

Modbus

®

RTU Serial Communications User Manual

Configuration/Remote Calibration Interfaces for HercuLine Actuators

HercuLink™ User Manual

HART Communications Installation and Operations Manual

61-86-03-14

62-86-16-21

51-52-25-66

51-52-25-103

62-86-25-11

62-86-25-12

Contacts

World Wide Web

The following lists Honeywell’s World Wide Web sites that will be of interest to our customers.

Honeywell Organization WWW Address (URL)

Corporate

Honeywell Process Solutions http://www.honeywell.com http://www.honeywell.com/ps

Telephone

Contact us by telephone at the numbers listed below.

United States and Canada Honeywell Support

1-800-525-7439 Service

Revision 7 HercuLine™ 2000 Series Actuator - Installation, Operation and Maintenance Manual iii

7/08

Symbol Definitions

The following table lists those symbols that may be used in this document to denote certain conditions.

Symbol Definition

This DANGER symbol indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury.

This WARNING symbol indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.

This CAUTION symbol may be present on Control Product instrumentation and literature. If present on a product, the user must consult the appropriate part of the accompanying product literature for more information.

This CAUTION symbol indicates a potentially hazardous situation, which, if not avoided, may result in property damage.

WARNING

PERSONAL INJURY:

Risk of electrical shock. This symbol warns the user of a potential shock hazard where HAZARDOUS LIVE voltages greater than 30 Vrms,

42.4 Vpeak, or 60 Vdc may be accessible. Failure to comply with these

instructions could result in death or serious injury.

ATTENTION, Electrostatic Discharge (ESD) hazards. Observe precautions for handling electrostatic sensitive devices

Protective Earth (PE) terminal. Provided for connection of the protective earth

(green or green/yellow) supply system conductor.

Functional earth terminal. Used for non-safety purposes such as noise immunity improvement. NOTE: This connection shall be bonded to protective earth at the source of supply in accordance with national local electrical code requirements.

Earth Ground. Functional earth connection. NOTE: This connection shall be bonded to Protective earth at the source of supply in accordance with national and local electrical code requirements.

Chassis Ground. Identifies a connection to the chassis or frame of the equipment shall be bonded to Protective Earth at the source of supply in accordance with national and local electrical code requirements. iv HercuLine™ 2000 Series Actuator - Installation, Operation and Maintenance Manual Revision 7

7/08

Contents

Contents

Introduction ............................................................................................. 1

Product Description ......................................................................................................1

Specifications .......................................................................................... 5

Technical and Operating Specifications .......................................................................5

Model Selection Guide ...............................................................................................10

Installation ............................................................................................. 12

Installation Overview ..................................................................................................12

Mechanical Stops .......................................................................................................12

Before Starting............................................................................................................13

Actuator Mounting ......................................................................................................13

Mechanical Installation ...............................................................................................15

Electrical Installation...................................................................................................17

Burner Control/Flame Safety................................................................. 23

Series 90 Control – HercuLine

®

2001 model only......................................................24

Split Range .................................................................................................................26

Master/Slave Arrangement.........................................................................................26

Set Up and Calibration Procedures....................................................... 31

Overview.....................................................................................................................31

Local Display and Keypad..........................................................................................31

Set Up Tips.................................................................................................................33

Set Up Groups............................................................................................................34

Set Up Procedure .......................................................................................................36

Configuration Prompt Hierarchy .................................................................................38

Input Set Up Group.....................................................................................................39

Relays Set Up Group..................................................................................................44

Current Out Set Up Group..........................................................................................49

Communications Set Up Group..................................................................................50

Digital Input Set Up Group .........................................................................................51

Display Set Up Group.................................................................................................52

Revision 7 HercuLine™ 2000 Series Actuator - Installation, Operation and Maintenance Manual v

7/08

Contents

Lock Set Up Group .....................................................................................................53

Read Status Set Up Group.........................................................................................55

Drive Set Up Group ....................................................................................................56

Maintenance Set Up Group........................................................................................59

Regions of Motor Travel .............................................................................................62

CAL POSOUT Group .................................................................................................63

Auto - Manual Drive Switch ........................................................................................64

Calibration ..................................................................................................................65

Setting End-of-Travel Limit Switches .........................................................................78

Setting Auxiliary Switches ..........................................................................................81

Start-Up/Operation ................................................................................ 83

Introduction.................................................................................................................83

Power-up Diagnostics.................................................................................................83

Operations Checklist ..................................................................................................83

Operating Displays .....................................................................................................84

Motor Stall ..................................................................................................................84

Position Sensor Operation .........................................................................................85

Remote Setpoint Operation........................................................................................85

Maintenance.......................................................................................... 87

Introduction.................................................................................................................87

Basic Maintenance .....................................................................................................87

Replacement Procedures...........................................................................................89

Replacement/Upgrade/Accessory Kits .................................................. 91

Replacement Kits .......................................................................................................91

Upgrade Kits.............................................................................................................102

Accessory Kits ..........................................................................................................104

Troubleshooting .................................................................................. 105

Introduction...............................................................................................................105

Troubleshooting Procedures ....................................................................................106

Appendix A - HercuLine

®

2001/2002 Configuration Record Sheet...... 112

Index ................................................................................................... 116

vi HercuLine™ 2000 Series Actuator - Installation, Operation and Maintenance Manual Revision 7

7/08

Contents

Tables

Table 1 Specifications - General.............................................................................................................................5

Table 2 Recommended Minimum Wire Size........................................................................................................17

Table 3 Terminal Connections: HercuLine

®

Table 4 Terminal Connections: HercuLine

®

2000...............................................................................................18

2001/2002 with auto/manual .........................................................19

Table 5 Split Range Set Up Procedure .................................................................................................................26

Table 6 Keypad Description .................................................................................................................................32

Table 7 Set Up Tips ..............................................................................................................................................33

Table 8 Set Up Groups .........................................................................................................................................34

Table 9 Set Up Procedure Using Display and Keypad .........................................................................................36

Table 10 Input Set Up Group Parameters .............................................................................................................39

Table 11 Equal Percentage Valve Characteristics ................................................................................................42

Table 12 Quick Opening Valve Characteristic .....................................................................................................43

Table 13 Relay Set Up Group Parameters ............................................................................................................44

Table 14 Relay Type Descriptions........................................................................................................................45

Table 15 Current Out Set Up Group Parameters ..................................................................................................49

Table 16 Communications Set Up Group Parameters ..........................................................................................50

Table 17 Digital Input Set Up Group Parameters .................................................................................................51

Table 18 Display Set Up Group Parameters .........................................................................................................52

Table 19 Lock Set Up Group Parameters .............................................................................................................53

Table 20 Read Status Set Up Group Parameters ..................................................................................................55

Table 21 Drive Set Up Group Parameters ............................................................................................................56

Table 22 Maintenance Set Up Group Parameters.................................................................................................59

Table 23 CAL POSOUT Group Parameters .........................................................................................................63

Table 24 Auto - Manual Switch Functions ...........................................................................................................64

Table 25 Input Calibration Procedure...................................................................................................................69

Table 26 Motor Calibration Procedure .................................................................................................................70

Table 27 Output Calibration Procedure ................................................................................................................71

Table 28 Slidewire Emulation Calibration Procedure ..........................................................................................73

Table 29 NCS Position Sensor Calibration Procedure.........................................................................................74

Table 30 Potentiometer Position Sensor Calibration Procedure ..........................................................................76

Table 31 Load Position Sensor Factory Calibration .............................................................................................77

Table 32 End-of-Travel Limit Switch Setting Procedure .....................................................................................79

Table 33 Auxiliary Switch Setting Procedure ......................................................................................................82

Table 34 Typical Operating Displays ...................................................................................................................84

Table 35 Spur Gear Lubrication Procedure ..........................................................................................................87

Table 36 Motor Drive Fuse Replacment Procedure .............................................................................................89

Table 37 Relay PWA Replacement Procedure .....................................................................................................90

Table 38 Replacement kits....................................................................................................................................96

Table 39 Observable Symptoms of Failure ........................................................................................................105

Revision 7 HercuLine™ 2000 Series Actuator - Installation, Operation and Maintenance Manual vii

7/08

Contents

Figures

Figure 1 HercuLine

®

Figure 2 HercuLine

®

2000 Series Actuator

2002 Actuator Internal View

Figure 3 Outline and Dimensions of HercuLine

®

2000 Series Actuators

Figure 4 Constant Torque Linkage

Figure 5 Variable Torque Linkage

Figure 6 Standard crank arm

Figure 7 Crank arm with optional ball joint and push rod

Figure 8 HercuLine

®

2000 connections

Figure 9 HercuLine

®

Figure 10 HercuLine

2001/2002 connections

®

2003 connections

Figure 11 CE wiring part 1

Figure 12 CE Wiring part 2

Figure 13 Burner Control/Flame Safety Wiring

Figure 14 Series 90 connections

Figure 15 T775 Controller connections

Figure 16 Flow Diagram

Figure 17 Interconnection Diagram

Figure 18 Proportional Flow Using Multiple Actuators

Figure 19 Multiple Actuator Interconnection Diagrams

Figure 20 Interconnection Diagrams

Figure 21 HercuLine

®

2000 Display and Keypad

Figure 22 Relay connectors

Figure 23 Regions of Motor Travel

Figure 24 Auto - Manual Switch

Figure 25 Calibration Wiring Connections (non-slidewire emulation)

Figure 26 Calibration Wiring Connections (slidewire emulation)

Figure 27 Jumper Location on CPU PWA

Figure 28 Location of NCS Assembly

Figure 29 Location of potentiometer position sensor

Figure 30 End of Travel Limit Switch Settings

Figure 31 Location of End-of-Travel Limit and Auxiliary Switches

Figure 32 Auxiliary Switch Settings

Figure 33 Terminal Block Connections for Modbus Communications

Figure 34 Spur Gear Location

Figure 35 Power Distribution PWA and Relay PWA Locations

Figure 36 Motor Drive Circuit Fuses

Figure 37 Replacement Kits 6, 7, 8, 11, 12, 14

Figure 38 Replacement Kit 10

Figure 39 Replacement Kits 1, 2, 3, 4, 5, 9, 15, 16, 19

Figure 40 Replacement Kit 13

Figure 41 Replacement Kits 17, 18

Figure 42 Test for Actuator Operation

Figure 43 Power Up Diagnostics

Figure 44 Test Power Distribution PWA

Figure 45 Test AUTO - MANUAL Switch

Figure 46 Test Relay Function

75

77

78

80

64

66

67

68

30

31

46

62

27

27

28

29

22

23

24

25

18

19

20

21

2

3

14

15

16

16

16

94

95

107

108

109

110

111

90

91

92

93

81

86

88

89 viii HercuLine™ 2000 Series Actuator - Installation, Operation and Maintenance Manual Revision 7

7/08

Introduction

Product Description

Introduction

Product Description

Honeywell’s HercuLine

®

2000 series actuators are available in four versions: HercuLine

®

HercuLine

®

2000,

2001, HercuLine

®

2002, and HercuLine

®

2003. All are low torque, precision electric rotary actuators incorporating all of the high quality and reliable features of the traditional HercuLine series actuators. These precision control and high reliability actuators ensure processes operate at maximum efficiency, with minimal downtime, and lowest lifetime cost.

Honeywell's HercuLine

®

2000 series actuators are precision engineered for exceptional reliability, accurate positioning, and low maintenance (Figure 1). Designed for very precise positioning of dampers and quarter turn valves the HercuLine

®

2000 series actuators perform especially well in extremely demanding environments requiring continuous-duty, high reliability, and low maintenance.

Model distinctions

HercuLine

®

2000 series actuators are used in applications requiring on/off or power to open/close position proportional with 135 or 1000 ohm feedback.

HercuLine

®

2001 and 2002 are smart actuators used in applications requiring current proportional control or digital control. They offer digital electronics providing for precision positioning control, easy set-up and configuration, on board health monitoring, and network communications. Programming access is provided through our HercuLink

®

Palm PDA software connected to the actuator via a 232/485 converter, via HART communications or through the optional local keypad and display.

HercuLine

®

2002 smart actuators offer features and functions similar to the HercuLine

®

2001 and are used for more severe service applications requiring features such as non-contact position sensing.

HercuLine

®

2003 actuators are unidirectional/ 360 degree rotation, special purpose actuators.

The keypad and display are available on the HercuLine

®

2001 and HercuLine

®

2002 products at additional charge.

HercuLink

®

Software

HercuLink

®

Computer software enables access to programming and communication functions available as standard with the HercuLine

®

2001 and 2002 actuators without the added expense of the keypad & display HMI. Using a Palm

™ PDA, laptop PC or desktop computer, HercuLink

®

software, and a

RS232/485 converter users may configure, calibrate, and access maintenance information locally or remotely to the actuator.

Using HercuLink

®

software, the computer may be used as a master device over a Modbus network to access information to/from the actuators and to control the device. Set-up configurations may also be stored on the computer for download to other HercuLine

®

devices. Information may be stored on the users

PC in CSV format for use in preventative maintenance programs.

• Certified on Palm™ m125, m130, and m505.

• Compatible with Palm OS3.5 or higher.

• Compatible with Windows 2000 or XP operating systems

• Minimum system requirements:

• Windows 2000 (w/service pack 2), Windows NT (w/service pack 5), Windows ME, Windows XP

• 200 MHz Pentium with 64 Megs Ram

Revision 7 HercuLine™ 2000 Series Actuator - Installation, Operation and Maintenance Manual

7/08

1

Introduction

Product Description

Display and keypad

Handwheel

Conduit entry

Shaft and position indicator

Auto/manual switch

Figure 1 HercuLine

®

2000 Series Actuator

2 HercuLine™ 2000 Series Actuator - Installation, Operation and Maintenance Manual Revision 7

7/08

Display

Keypad

PWA

Introduction

Product Description

Wiring

Label

TB3

Connector for customer input and output connection on CPU

PWA

Cams and limit switches

Non-contact sensor

TB1 customer power connection

External auto-manual switch


®

2002 Actuator Internal View


7/08

3

Introduction

Product Description


7/08

Specifications

Technical and Operating Specifications

Specifications

This section provides you with the technical specifications and the model selection guide for the

HercuLine

®

2000 Series Actuators.

Technical and Operating Specifications

Table 1 Specifications - General

Weight

Enclosure

Gear Train

Mechanical Stops

Storage Temperature

Relative Humidity

Scale

Crank Arm

Output Shaft

Rotation

Manual Handwheel

Lubrication

Output Torque/Full

Travel Stroking Time

Physical

2000: 25 lb. (11.36 kg)

2001,2002: 27 lbs. (12.27 kg)

Precision-machined die cast aluminum housing, finished in light gray powder coat epoxy.

Alloy steel, high efficiency steel spur gear primary train. Precision ground, selflocking/self releasing worm gear final mesh.

Factory set at 90° or 150° (+/-5°).

Attention: Do not adjust the mechanical Stops. Adjusting the stops will void

the warranty

–40 °C to +93 °C (–40 °C to +200 °F)

0 % to 99 % R.H. non-condensing over the full operating temperature range.

0 % to 100 % corresponding to full crank arm travel.

Adjustable radii 1.0 in (25.4mm) to a maximum of 2.8 in (71.1mm). Position adjustable through 360° rotation.

0.625+/-.005 in (15.88 +/-.13mm) diameter

90° or 150° degrees between 0 % and 100 % on scale, limited by mechanical stops.

Provides a means of positioning the actuator in the event of a power failure or setup.

Texaco Starplex 2 EP Grease

Torque lb-in (N

M)

50 / (6.0)

100 / (11.5)

200 / (22.5)

400 / (45.0)

400 / (45.0)

50 Hz (90

4.5 / 7.5

9 / 15

18 / 30

36 / 60

54 / 90

°/150°)

60 Hz (90

4 / 6

7 / 12

15 / 25

30 / 50

45 / 75

°/150°)


7/08

5

Specifications


Mains Supply

Motor

Motor Current

Loss of Power

Local Auto/Manual Switch

End of travel Limit

Switches

Auxiliary Switches/Relays

Approvals

Enclosure Rating

Clamp Bolt

Electrical

100-130 Vac single phase, 50 Hz or 60 Hz

200-240 Vac single phase, 50 Hz or 60 Hz

Instant start/stop, non-coasting, non-burnout, continuous duty, permanent magnet, synchronous induction motor. Can be stalled up to 100 hours without damage.

=

No load = full load = locked rotor = 0.4 amp for 120Vac, 0.2 amp for 240 Vac

Stays in place on loss of power

Optional – Allows local and automatic operation of the actuator.

Standard – adjustable to limit actuator travel to less than 90 or 150 degrees respectively

Optional – Up to 4 additional SPDT switches rated at (10 A at 125 Vac, 5 A at 250

Vac).

Certifications

CSA/UL (Standard)

CE Compliant (optional)

Type 4 (NEMA 4), IP66 (standard)

Torque Settings of Crank Arm Bolts

88 lb-in (10 N-m)

Input Signals

Isolation

Electrical and Performance Specifications

Load Requirement (4-20)

Input Impedance

Feedback

HercuLine

Analog:

•

®

2002

0/4 to 20 mA (With CPU

PWA jumper in current position)

•

•

0/1 to 5 Vdc

0 to 10 Vdc

Digital:

•

Modbus RTU (RS485)

HercuLine

®

2001

Analog:

• 0/4 to 20 mA (With CPU

PWA jumper in current position)

•

•

•

0/1 to 5 Vdc

0 to 10 Vdc

Series 90 control

Digital:

• Modbus RTU (RS485)

Input signal, output signal and power are isolated from each other.

Current Out — 0 to 1000 ohms

0/4 to 20 mA

0/1 to 5 Vdc

0-10 vdc

250 ohms

10 K ohms

0 to 20 mA, 4 to 20 mA

0 to 5 Vdc & 1 to 5 Vdc with 250 ohm resistor, (0 to 16 Vdc with 800 ohm resistor)

HercuLine

®

2000/2003

120 vac drive open/120 vac drive close

240 vac drive open/240 vac drive close

NA

NA

NA

Dual output 1000 ohms over 90 degrees (135 ohms with 158 resistor)

Dual output 1000 ohms over 150 degrees (135 ohms with with 158 resistor)


7/08

Specifications


HercuLine

®

2002

Feedback

Slidewire emulation - Provides output voltage ratiometric to shaft position and potentiometric to supply voltage

(1 Vdc to 18 Vdc) without a slidewire. Emulates a 100 ohm to 1000 ohm slidewire. 10 mA output maximum.

Communications

Modbus RTU or optional HART

™

Operating Temperature

–40°C to +75 °C (–40°F to +170 °F)

HercuLine

®

2001 HercuLine

®

2000/2003

Position sensing

Sensitivity

Hysteresis

Deadband

Repeatability

Repositions

(minimum @ 90 or 150 degree stroke)

Table 1 option –050-





Voltage/ Supply

Stability

Temperature

Coefficient

Zero Suppression

Input Filters

Solid State Motor

Control

Failsafe operation

Direction of Rotation

Duty Cycle

Non-contact position sensor 1000 ohm film potentiometer

0.2 % to 5 % of 90° span, proportional to deadband

Less than 0.4 % of full scale

0.2 % to 5 % of 90° span, programmable. Shipped at 0.5 %

0.2 % of 90° span

160

290

450

700

900

120

250

400

400

400

0.25 % of span with +10/–15 % voltage change

NA

NA

NA

NA

NA

-40°C to +85 °C (-40°F to

+185 °F)

Dual 1000 ohm film potentiometers

(not on 2003)

NA

500

Less than

± 0.030 % of span per degree C for 0 °C to 50 °C

Less than

± 0.05 % of span per degree C for –40 °C to 75 °C

90 % of span.

Selectable spike and low pass filters.

Two triac switches for clockwise or anti-clockwise motor operation.

Transient voltage protection provided.

NA

NA

NA

NA

If input signal exceeds configured input range. Selectable and adjustable.

NA

Field programmable Wire swap

Continuous


7/08

7

Specifications


Programmable

Functions

HercuLine

®

2002 HercuLine

Selectable and configurable operating parameters:

®

2001 HercuLine

®

2000/2003

NA

•

•

•

•

•

•

•

•

•

•

•

•

•

•

Input range

Input filtering

Input characterization

Security

Digital Input action

Deadband

Failsafe on loss of input signal

Failsafe on loss of position sensor

Direction of rotation

Relay closure action

Communication parameters

Split range operation

Output range

Alarms

Specifications – Local Display and Keypad

Display Design

LED indicators

Display Operating

Temperature

Storage Temperature

Keys

Display

Multi-segment LED displays that provides up to ten alphanumeric characters. Display arrangement consists of two rows:

1 st

row (Upper display) – four characters

2 nd

row (Lower display) – six characters.

Six single LEDs provide actuator status and alarm indications.

-30 °C to +50 °C (-20 °F to +122 °F)

Automatically shuts off when operating temperature exceeds +50 °C

-40 °C to +93 °C (-40 °F to +200 °F)

Keypad

Six single pushbutton keys allow access to all status displays and set up group parameters.

See Set Up and Calibration Procedures (page 31) for detailed information on display and keypad functions.


7/08

Specifications


Specifications – Communications

Communications

RS 485 Serial Communication, Modbus RTU Protocol

Communications

Option

Connection

Maximum loop length

Communication Mode

Baud Rate

Twisted pair cable with shield

600 meters (2000 feet)

Half duplex

300, 600, 1200, 2400, 4800, 9600, 19.2K

Operating System

RAM

Communications

Required Specifications – PDA (customer provided)

PDA

Palm OS version 3.5 or greater

At least 8 MB

Serial port with RS232 compatible levels to drive external converter

Note: As of this writing only Palm devices have this feature. Honeywell has qualified the M105, M125, M130, and M505 devices with the HercuLink application.


7/08

9

Specifications

Model Selection Guide

Model Selection Guide

Instructions

Select the desired key number. The arrow to the right marks the selection available.

Make the desired selections from Tables I thru VIII using the column below the arrow.

A dot ( ) denotes unrestricted availability.

Key Number

_ _ _ _

-

I

_ _ _ -

II

_ _ _ -

III

_ _ _ -

IV

_ _ _

V VI VII

- _ _ - _ _ _ _ _ _ _

VIII IX

-

_

-

_ _

KEY NUMBER - Motor Selection

Basic Motor Unit (no electronics)

Basic Motor Unit plus Digital Electronics

Enhanced Performance Motor Unit with Non-contact Position Sensing

Unidirectional Motor (M640D Replacement)

TABLE I - TORQUE & SPEED SELECTION (speed per 150 degree rotation)

Torque, lb-in/(N-M)

50Hz 60Hz

50 / (6.0)

100 / (11.5)

200 / 22.5)

400 / (45.0)

400 / (45.0)

7.5 sec

15 sec

30 sec

60 sec

90 sec

6 sec

12 sec

25 sec

50 sec

75 sec

TABLE II - ROTATION

Travel 90 degrees

150 degrees

360 degrees

TABLE III - POWER SUPPLY

Single Phase 100 - 130 Vac, 60 Hz

100 - 130 Vac, 50 Hz

200 - 240 Vac, 60 Hz

200 - 240 Vac, 50 Hz

TABLE IV - ANALOG INPUT/OUTPUT SIGNALS

Input 3 Wire Drive up/down

0/4-20 mA, 0/1-5 Vdc, 0-10 Vdc

0/4-20 mA, 0/1-5 Vdc, 0-10 Vdc

Output

0 to 135 ohm input (Series 90 control)

Contact Input for 2003

None

(Note 1)

(Note 1)

Dual 1000 Ohm (1000 ohms over 150 degrees)

Dual 1000 Ohm (1000 ohms over 90 degrees)

Slidewire Emulation

Slidewire Emulation

0/4-20mAdc (0/1-5 Vdc, 0-16 Vdc)

0/4-20mAdc (0/1-5 Vdc, 0-16 Vdc)

TABLE V - SWITCH AND RELAY OUTPUTS

(2 end-of-travel switches are standard)

Auxiliary Outputs No Auxiliary Switches

2 Auxilliary Switches

4 Auxilliary Switches

Relay Outputs No Relays

2 Programmable Relay Outputs



Selection

2000

2001

2002

2003

050

100

200

400

600

090

150

360

126

125

246

245

0 _

2 _

4 _

_ 0

_ 2

_ 3

_ 4

_ 15

_ 19

_ 60

_ 65

_ 80

_ 85

0 _ _

2 _ _

3 _ _

4 _ _

6 _ _

_ 00

b c

Availability a

continued


7/08

Specifications

Model Selection Guide

2000 2001 2002 2003

TABLE VI - OPTIONS

Local keypad/ display

Local Auto/ manual switch

Handwheel

Certificates

Approvals

Shipped Rotation

No local display interface supplied

(Note 2)

Integrally mounted local display/keypad interface

No auto/manual switch

Auto/manual switch with "Out of Auto Contact"

Auto/manual switch with "Out of Auto Contact"

No Handwheel

Handwheel

None

Certificate of Conformance

UL Type 4/IP66, CSA

CE

(Note 4)

Counter clockwise shaft rotation on increasing signal

Clockwise shaft rotation on increasing signal

TABLE VII - COMMUNICATIONS/PROTOCOL

None No communications option board or protocol

Modbus RTU RS485 RS-485 Modbus compliant - standard with EEU

HART 5 HART Communications Protocol

TABLE VIII - MANUALS

Standard English

TABLE IX - FACTORY OPTIONS

Factory Options None

Restrictions

Restriction

Letter a b c

Available Only With

Table Selection

IV

II

II

_ 00

150

090

Not Available With

Table Selection

IV

II

II

_ 60, _ 80

090

150

Selection

0_ _ _ _ _

1_ _ _ _ _

_ 0_ _ _ _

_ 1_ _ _ _

_ 2_ _ _ _

_ _ 0_ _ _

_ _ 1_ _ _

_ _ _ 0 _ _

_ _ _ 1_ _

_ _ _ _ 0_

_ _ _ _ 1_

_ _ _ _ _0

_ _ _ _ _1

0

1

2

0

00

ACCESSORIES

Mounting Hardware Mounting plate adapter for Barber Colman Series MP495

Mounting plate adapter for Landis & Staefa SQM53/56

Direct Couple Valve Hardware

North American Valve Retrofit Kit

Linkage Assembly

HART

Handheld Config.

Ball joint for 5/16" dia. Pushrod

Pushrod 12 in. (304,5 mm) long, 5/16 " dia.


Pushrod 24 in. 609,6 mm) long, 5/16 " dia.


Turk Cable for Handheld Connection

HercuLink

TM

Palm Software

(Note 3)

Remote Mount

Control

Battery powered 232/485 converter with cable

Remote 4-20 mA requires 135 ohm fdbk, 120V 50/60Hz



Remote 135 ohm input requires 135 ohm fdbk, 120V 50/60Hz

51452354-501

51452354-502

51452354-503

51452354-511

51452354-504

51452354-505

51452354-506

51452354-507

51452354-508

51452352-501

51452354-509

51452354-510

R7195A1031

R7195A1056

R7195A1064

R7195B1021

Notes:

1. 135 ohm available by parallelling 1K potentiometer with 158 Ohm resistor (supplied).

2. HercuLink

TM

software (pn 51452354-509), RS232/485 converter (pn 51452354-510),

customer supplied Palm

TM

PDA running OS3.5 or higher and Palm serial cable are required

for the 2001 and 2002 actuators if no display is selected.

3. Requires PDA manufacturer's serial interface cable.

4. CSA approval is good for 75°C and a maximum relay load of 3.5 amps or 70°C with a relay load of 5 amps.


7/08

11

Installation

Installation Overview

Installation

Installation Overview

The procedures to install the HercuLine

®

2000 Series actuator and place it in service require that you:

•

Select a suitable location for installation. (See Installation Considerations below.)

•

Mount the actuator securely.

•

Install mechanical connections or linkage between control arm and final control element. Use HAL software application to aid in mechanical installation.

•

Make all electrical connections for actuator according to local and national electrical codes.

•

Power up actuator.

•

Enter, verify and adjust set up parameters for proper operation.

•

Adjust control arm linkage for accurate operation of final control element.

This section provides you with mechanical and electrical installation information required to mount and connect the HercuLine

®

2000 Series Actuator to your specific application. Unpacking instructions, installation consisderations, electrical and safety precautions also included in this section should be observed.

Mechanical Stops

Factory set at 90° or 150° (+/-5°).

See Figure 2 for location.

Attention: Do not adjust the mechanical stops. Adjusting the stops will void the warranty.


7/08

Installation

Before Starting

Before Starting

Unpacking

If there are visible signs of damage to the shipping container, notify the carrier and Honeywell immediately.

If there is no visible damage, compare the contents with the packing list. Notify the carrier and Honeywell immediately if there is equipment damage or shortage.

Please do not return goods without contacting Honeywell Applications Center in advance. The contact number is 1-800-423-9883.

Installation Considerations

Mount the actuator in a location where it will be easily accessible for maintenance and for manual operation by means of the handwheel. The exact location must be determined in accordance with the linkage used.

It is important that the actuator be mounted securely to a solid foundation commensurate with the maximum torque developed. Use studs or bolts that are as large as the foot mounting holes.

Allocate sufficient clearance around the actuator for the removal of all covers to permit inspection of internal parts and to provide access to the handwheel.

Actuator Mounting

Firmly bolt the actuator to a mounting surface that will not distort when subjected to the torque stresses generated by the actuator. The output shaft of the actuator should be parallel to the output shaft of the driven device. The output shaft crank arm is fully adjustable through 360

°.

Mounting holes (bottom and side) and location of shaft/crank arm duplicate mounting for Honeywell

Actionators M640A, 740A, 940A for drop-in replacement. Optional adaptor plates available for replacing

Landis and Staefa SQM53/56 and Barber Coleman series MP495 models.


7/08

13

Installation

Actuator Mounting

CLEARANCE FOR TOP REMOVAL:

101,6

mm inches

Figure 3 Outline and Dimensions of HercuLine

®

2000 Series Actuators


7/08

Installation

Mechanical Installation

Mechanical Installation

Linkage Set-up

Many applications require the use of a linkage assembly and often the final control element does not have a linear torque curve. The actuator linkage can be set up to achieve an optimal delivered torque distribution for specific applications. To assist with linkage design, Honeywell offers a linkage analysis software application

(HAL). The software can be ordered as P/N 51197910-001.

Constant Torque Linkage (typical)

A constant torque linkage is employed when it is desired to provide a linear torque profile throughout the full range of final control element travel. In this situation, the actuator and driven crank arms will be set-up proportionally with respect to each other. Figure 4 shows a general linkage setup to achieve a linear torque profile.

Vertical

Centerline

45° 45°

Linkage

Vertical

Centerline

45° 45°

Start Stop Close Open

Drive Unit

Crank Arm

Horizontal Offset

Damper

Crank Arm a/n 23199

Figure 4 Constant Torque Linkage

Variable Torque Linkage

A variable torque linkage is employed when it is desired to provide a non-linear torque profile throughout the full range of final control element travel. In this general situation, the actuator and driven crank arms will be set up to provide a higher torque for seating or unseating the final control element. Figure 5 shows a general linkage setup to achieve a non-linear torque profile. Note that this linkage can be characterized in many different ways by varying start angles and rotation requirements of both the Actuator Crank Arm and the Driven

Arm.


7/08

15

Installation

Mechanical Installation

Vertical

Centerline

Vertical

Centerline

45° 45°

Actuator

Crank Arm

Linkage

Close Open

5° a/n 23200

Horizontal Offset

Damper

Crank Arm

Figure 5 Variable Torque Linkage

Actuator Crank Arms

The HercuLine

®

2000 Series Actuator comes standard with a crank arm with adjustable radius of 1.0 in

(25.4mm) to 2.80 in (71.12mm). See Figure 6.

Figure 6 Standard crank arm

Figure 7 Crank arm with optional ball joint and push rod


7/08

Installation

Electrical Installation

Electrical Installation

General Wiring Recommendations

Only qualified personnel should perform wiring.

Wiring must conform to national and local electrical codes.

In general, copper wire used. Unless locally applicable codes dictate otherwise, the recommended minimum wire sizes in Table 2 should be observed.

Table 2 Recommended Minimum Wire Size

AWG

14

18

Description

Earth ground wire to common power supply.

Earth ground wire to single actuator. 120/240 V ac line leads. +24 V and common signal leads. Common signal leads, relays, and aux switches.

Safety Precautions

An external disconnect switch must be installed to break all current carrying conductors connected to the actuator. Turn off power before working on conductors. Failure to observe this precaution may result in serious personal injury.

Actuator Connections

ATTENTION

The ground terminal must be connected to a reliable earth ground.

While the unit is powered, a potentially lethal shock hazard exists inside the case.

Do not open the case while the unit is powered. Do not access the terminals while the unit is powered.

The actuator terminal connections for the field wiring are located behind the cover on the actuator case as shown in Figure 2. Power and field wiring is brought into the actuator through two access holes located on the side of the actuator case.

Use both openings: one for low level wiring (control signal) and the other for high level wiring (120Vac).

Do not run both the High Level and Low Level wiring through the same opening.

The screw terminals, locations, and descriptions for all customer connections are identified in the tables and figures that follow.


7/08

17

Installation


HercuLine

®

2000 Terminal Connections

Table 3 Terminal Connections: HercuLine

®

2000

Connection Terminal Numbers and LABEL

Descriptions

See Figure 8

Neutral

Auto/Manual Switch

Contact

CW from Controller

CCW from Controller

Potentiometer #1

Potentiometer #2

Protective Ground

158 ohm

2

3

4

5

6

7

8

9

10

11

12

158 ohm switch is present.

Neutral wire for 120/240VAC mains supply

Switch contact to indicate setting of actuator AUTO/MANUAL switch.

Switch is closed when actuator is “NOT-IN-AUTO”

CW motor drive

CCW motor drive

Clockwise-End

Slider

Counterclockwise-End

Clockwise-End

Slider

Counterclockwise-End

Ground wire connection for mains supply

Install resistors to convert 1000 ohm potentiometer to 135 ohms

REQUIRED ONLY IF AUTO/MANUAL

SWITCH IS PRESENT


®

2000 connections


7/08

Installation


HercuLine

®

2001/2002 with Auto/Manual Terminal Connections

Table 4 Terminal Connections: HercuLine

®

2001/2002 with auto/manual

Connection Terminal Numbers and LABEL

Descriptions

See Figure 9

Hot

Neutral

TB1

1

2

4 to 20mA Output* 1 (+)

2 (-)

Feedback 3

Hot wire for 120/240VAC mains supply

Neutral wire for 120/240VAC mains supply

Protective Ground

Auto/Manual Switch

Contact

3

4

5

Ground wire connection for mains supply

Switch contact to indicate setting of actuator AUTO/MANUAL switch.

Switch is closed when actuator is “NOT-IN-AUTO”

6

TB3

Analog signal output

Feedback signal used in conjunction with 4 to 20mA OUTPUT voltage when using Slidewire Emulation

Analog signal input 4 to 20mA Input

Modbus

Communication

4 (+)

5 (-)

6 (+)

7 (-)

8 Shield

HART Communications 4 (+)

5 (-)

Digital Input 9 Com

10 Input

Connection for RS485 Modbus loop wires

HART Communication is 4-20 mA only.

Customer’s contact closure


®

2001/2002 connections


7/08

19

Installation


HercuLine

®

2003 Wiring Connections and Operation (Actionator 640D Replacement)

Wiring


®

2003 connections

Operation

The 2003 actuator is uni-directional (it does not reverse rotation with a reversal in control action).

Figure 10 illustrates the internal wiring and the external connections.

The smaller insert of the figure describes the limit switch action for one complete cycle. When the two-position controller detects a sufficient fall in temperature in a heating application, the switch portion between the “4” and

“5” terminals will close.

The motor then rotates for 180º or until the opening switch breaks (stops are adjustable, factory set at 180º), and stops in full open position.

A subsequent rise in temperature causes the controller to close the switch between the “4” and “6” terminals when the motor will start to rotate (in the same direction) for 180º or until the closing switch breaks.

The motor stops in the closed position and completes one cycle.


7/08

Installation


Power Connections

Depending on which power supply selection is ordered for your actuator, wire the power input (MAINS

POWER) as described in the previous tables and figures. Wiring must conform to national and local electrical codes.

CE Wiring

When wiring the actuator power input for CE approved units, you must also install a MOV and ferrite beads supplied with the CE unit.

You need the following tools:

•

5mm hex key

• small flat blade screwdriver

• small needle nose pliers



Step

1

2

3

4

5

6

7

Action

Remove AC power to actuator.

Loosen the 6 captive screws (use 5mm hex key) and remove the cover.

Locate the terminals TB1-1, TB1-2 and ground screw.

Loosen the screws at terminals TB1-1 and TB1-2. Remove screw used for ground.

Install the appropriate MOV assembly as shown in Figure 11.

All ferrites require 1 loop of wire per ferrite. Connect as shown in following steps.

• Current input and output (slidewire emulation) connection

•

Communications and digital input connection

Ground screw

TB1-2

TB1-1

Current input and output

(slidewire emulation)

Communications and digital input

Figure 11 CE wiring part 1


7/08

21

Installation


Step

8

• AC power connection

• Auxiliary switches connection

• Relay contact connection

Action

Aux switches

1 and 2

(SW3 and SW4)

Aux switches 3 and 4

(SW5 and SW6)

Relays 1 and 2

Relays 3 and 4

AC power connection

Figure 12 CE Wiring part 2

9

Install new gasket and top cover. Secure top cover with 6 captive screws.

10

Reapply AC power to the actuator.

11

Actuator is ready for use.

Input Signal Connections

ATTENTION

Shielded and grounded cables are recommended.

0/4-20 mA Input Signals

For current signal input, ensure jumper W2 on the CPU PWA is in the “Current” position. See Figure 27 on page 68. Observing polarity, connect the signal input wires TB3–4(+) and TB3–5(-) on CPU terminal board.

0/1-5 Vdc and 0 to 10 Vdc Input Signals

For voltage signal input, ensure jumper W2 on the CPU PWA is in the “Voltage” position. See Figure 27 on page 68. Observing polarity, connect the signal input wires to terminals TB3–4(+) and TB3–5(-) of the terminal block.


7/08

Burner Control/Flame Safety


Output Signal Connections

0/4-20 mA, 0/1-5 Vdc Feedback Signal Connections

ATTENTION


Actuator output is a 4 to 20 mA analog signal. If a voltage input is required for customer devices, a range resistor is needed at the device input. Refer to (page 19) for more information.

Slidewire Emulator Connections

ATTENTION


If you ordered the Slidewire output option for your actuator, it is set at the factory to provide an output that emulates 100 to 1000 ohm slidewires. Refer to (page 19) for more information.

Burner Control/Flame Safety

Introduction

Often, Gas Fired control applications use a Flame Safety System that drives the gas valve to full closed and full open during the start-up sequencefor the burner. HercuLine® 2000 Series actuators have been designed to be compatible with the Flame Safety Systems and to perform the required operations.

Configuration

In the Input Set Up Group (Page 39), configure the parameter FSTYPL to Down .

In the Digital Input Set Up group (Page 51), configure the parameter DIG INP to Up.

Wiring

Figure 13 Burner Control/Flame Safety Wiring shows a Typical Flame Safety Module wiring diagram.

• • • • • • • • • • • • • • • • •

• • • • • • • • • • • • • • • • •

To TB3 #10

To TB3 #5

1 2 3 4 5 6 7 8 9

+ –

Typical Flame

Safety Module

• • • • • • • • • • • • • • • • •

+ 4 to 20 Output from Controller

– 4 to 20 Output from Controller

Figure 13 Burner Control/Flame Safety Wiring


7/08

23


Series 90 Control – HercuLine® 2001 model only

Series 90 Control – HercuLine

®

2001 model only

Series 90 Controls are commonly used in building environmental systems and flame safeguard systems to provide modulating control. The control is affected by balancing a 135 ohm potentiometer. The HercuLine

2001 provides an emulation of this system as follows. The current output is used to excite the potentiometer in the controller. To do this it is set permanently at 11 ma. This produces a 1.5 volt span. The wiper is then connected to the HercuLine 2001 input, which is operating in voltage mode. The returns from both the input and the output are tied together.

Series 90 terminals are typically color coded white, red and blue. Conventionally, red is the wiper and white and blue are the two ends of the potentiometer. On a drop in temperature, the wiper moves toward the blue terminal.

Connections

4-20mA output

TB3

1+

2-

White

4-20mA input

4+

5-

Red

Blue

Figure 14 Series 90 connections

Considerations

1. This connection performs an emulation of a series 90 motor. If the controller being used is also an emulation of a Series 90, the connections required may be different. Shown in Figure 15 are the connections found necessary to connect a T775 controller through an S443A S90 Auto/Manual Control. If the controller has the capability to provide a 4/20 or voltage output, it is easier to use that mode. It will require only two wires and it will allow the independent use of the 4/20 output. If help is required, contact

Honeywell.

2. Due to variations in the definition of rotation directions, it may be necessary to reverse the action of the actuator from CCW to CW or vice versa.


7/08


Series 90 Control – HercuLine® 2001 model only

I out from

HercuLine2001

Auto

T775 B 3

W

R

T775 W 1

+ Signal to

HercuLine2001

R

Man

GND to

HercuLine2001 (2)

B

B T775 R 2

Figure 15 T775 Controller connections

3. In the T775 controller manual there are several examples of using resistances or potentiometers as high and low limit controls. Because of the mode of emulation of Series 90, it is likely that these connections will not work as intended. Instead, use the output or input limits which are programmable in the

HercuLine

®

2001.


7/08

25


Split Range

Split Range

The HercuLine

®

2001/2002 actuators can be set up to operate within a narrow input range (for example,

4 to 12mA input) in certain applications. The procedure in Table 5 describes how to set up an actuator to operate as part of a split valve configuration.

Table 5 Split Range Set Up Procedure

Step Action

To Set Actuator span to operate from 4 to 12 mA input.

1

Enter Set Up mode by pressing SET UP key

2

3

Select SET INPUT group

Press FUNCTION key until INP HI (on lower display) is selected.

4

5

Set INP HI value to 50.0

Press FUNCTION key to select INP LO and set value to 0.0

6

Press DISPLAY key to exit Set Up mode.

To Set Actuator span to operate from 12 to 20 mA input.

1

Enter Set Up mode by pressing SET UP key

2

3

Select SET INPUT group

Press FUNCTION key until INP HI (on lower display) is selected.

4

5

Set INP HI value to 100.0

Press FUNCTION key to select INP LO and set value to 50.0

6

Press DISPLAY key to exit Set Up mode.

ATTENTION

Be sure to review failsafe strategy for your process application.

Master/Slave Arrangement

Introduction

With the motor positioner, the controlling signal for the actuator is a 4 to 20mA from a current output controller as shown in the flow diagram in Figure 16.

Unlike the position output controller, the current output controller must produce a continuous analog signal or the actuator will revert to one of its failsafe states. Signal failure is not a problem since the available failsafe settings allow you to set the actuator position on signal loss.


7/08


Master/Slave Arrangement

Basic Flow Control

When the process variable signal is below set point, the controller increases current (4 to 20mA) to the actuator input and opens the valve. Controller set point governs valve position to obtain desired flow rate.

Orifice Plate

PV

FT

SP

FIC

Controller

4 to 20 mA

Positioner & Actuator

MP

Linkage

Valve

Position mA

Figure 16 Flow Diagram

Current Output Controller

+

4 to 20 mA

-

Actuator

See Figure

27 for jumper location

Jumper W2

250 Ohms

1 to 5 VDC

Hot

Neutral

Ground

120/240

VAC

Figure 17 Interconnection Diagram

Proportional Flow using Multiple Actuators

Refer to flow diagram in Figure 18 and interconnection diagrams in Figure 19. The controller governs flow rate in one burner. Only that flow is measured. Since #2 and #3 motor positions receive the same signal as #1 motor positioned, valves #2 and #3 will deliver the same amount of fuel. This is true when the span and zero adjustment are all set the same as in curve 2 of the graph. Other relationships between units exist if the span adjustment (3) for ratio or if the zero adjustment is changed (1) for bias.


7/08

27



Orifice Plate

SP

FIC

PV

Controller

4 to 20 mA

Position with Bias

Proportional

Ratio

FT

Positioner & Actuator

MP

#1

Linkage

Valve

MP

#2

Linkage

MP

#3

Linkage

Valve

Valve mA

Figure 18 Proportional Flow Using Multiple Actuators


Actuator #1

10260S Series Actuator #1

Note: Controller must be capable of sourcing the impedance.

+

-

4 to 20 mA

See Figure


Jumper W2

= Current

250 Ohms

1 to 5 VDC

Hot

Neutral

Ground

Actuator #2


120/240

VAC

Jumper W2

= Current

250 Ohms

1 to 5 VDC

Hot

Neutral

Ground

Actuator #3


120/240

VAC

Preferred

Wiring

Jumper W2

= Current

250 Ohms

1 to 5 VDC

Hot

Neutral

Ground

120/240

VAC

NOTE: If using HART

®

communications, for this application HART

® must be configured for Multi-drop operation.


7/08




+

4 to 20 mA

-

Jumper W2

= Current

1 to 5 VDC

Hot

Neutral

Ground

120/240

VAC

See Figure


Jumper W2

= Voltage

Hot

Neutral

Ground

120/240

VAC


Actuator #3

Alternate

Wiring

Jumper W2

= Voltage

Hot

Neutral

Ground

120/240

VAC

Figure 19 Multiple Actuator Interconnection Diagrams


®


®

must be configured for Multi-drop operation.


7/08

29



Split Valve Configuration

A common heat or cool type process requires two valves. In this case the controller has only one output.

The two motor positioners are calibrated differently, one responds to 4 to 12mA and the other responds to 12 to 20mA. At 12mA, both valves are closed; one opening below 12mA and the other above 12mA.

Refer to Figure 20 for an interconnection diagram for split valve operation using two actuators.


Note: Controller must be capable of sourcing the impedance.

+

4 to 20 mA

-

Jumper W2

1 to 5 VDC

Hot

Neutral

Ground

120/240

VAC

See Figure


Preferred

Wiring

Jumper W2

= Current

250 Ohms

1 to 5 VDC

Hot

Neutral

Ground

120/240

VAC


®


®



+

4 to 20 mA

-

Jumper W2

1 to 5 VDC

Hot

Neutral

Ground

120/240

VAC

See Figure


Alternate

Wiring

Jumper W2

= Voltage

Hot

Neutral

Ground

120/240

VAC

Figure 20 Interconnection Diagrams


®


®



7/08

Set Up and Calibration Procedures

Overview

Set Up and Calibration Procedures

Overview

Once you have installed the actuator, you can verify, set or change certain operating parameters. Set up is accomplished through use of the local display and keypad interface through your PDA with HercuLink

® software (see HercuLink

®

manual 62-86-25-11) or via the HART

®

communication option. Please keep in mind that the unit is calibrated at the factory for your application and can be placed into service right out of the box. Changing operating parameters may require recalibration of the actuator. This section details the various operating parameters and functions of the actuator available using the local display and keypad interface, and calibration procedures.

Local Display and Keypad

The alphanumeric display and keys on the keypad are the local operator interface for control, monitoring, and configuration of the actuator. The display consists of a four character upper display and a six character lower display. Six LEDs of various colors indicate actuator-operating status. Directly below the display are six keys that allow you to setup, monitor, and control the actuator locally, as well as call up various operating parameters and configuration values on the display. Figure 21 shows the physical features of the display and keypad. Table 6 summarizes the various functions you can perform using the keys as well as descriptions of the status indicators.

Upper Display

(Four Characters)

Lower Display

(Six Characters)

STALLED

ALARM

MANUAL

AUTO

SET UP FUNCTION

MAN/AUTO

DISPLAY


®

2000 Display and Keypad


7/08

31


Local Display and Keypad

Key or

LED Indicator

SET UP

FUNCTION

Table 6 Keypad Description

Function

Places the actuator in the set up group select mode. Sequentially displays the set up groups and allows the FUNCTION key to display function parameters within the set up group.

See Set Up and Calibration Procedures (page 31)Error! Reference source not

found.

for descriptions of the various options available in the set up groups.

Used in conjunction with the SET UP key to select the individual functions of a selected configuration set up group.

Used during field calibration procedure.

INCREMENT

Increases the configuration values shown on the display. Also shown as .

In manual mode and POSition display selected, pressing this key will drive actuator motor in direction of increasing signal input.

DECREMENT

Decreases the configuration values shown on the display. Also shown as .

In manual mode and POSition display selected, pressing this key will drive actuator motor in direction of decreasing signal input.

Indicates the movement of the actuator arm in the counterclockwise direction.

NOTE: Actuator rotation is the direction of the output shaft when facing the end of the shaft and refers to the direction of rotation on increasing signal.

☼

Indicates the movement of the actuator arm in the clockwise direction.


☼

☼

STALLED

Indicates that the actuator has detected a motor stall condition.

☼

DISPLAY

ALARM

☼

MANUAL

MAN

- Actuator is in Manual mode.

AUTO

- Actuator is in Automatic mode.

NOTE: When in Manual mode the POS display is automatically selected so you can use the up and down arrow keys to drive actuator motor manually.

NOTE: This button is disabled if MAENAB is set to DIS. See Table 19 (page 53).

Pressing this key repeatedly cycles through the operating parameters that can be shown on the lower display.

INP –

Input. Shows the value of the actuator input.

OP

– Output. Shows the value of the actuator output

DE –

Deviation. Shows deviation between input value and actuator position.

POS –

Position. Shows current actuator position.

Indicates a programmed alarm condition exists.

Indicates actuator is in manual mode

☼

AUTO

Indicates actuator is in automatic mode.


7/08


Set Up Tips

Set Up Tips

Table 7 contains tips that will help you view, verify and enter the operating parameters more quickly. If you cannot change the parameters, check the status of the “SET LOCK” parameter. Also some parameters require that you enter a security password before you access or change the parameter value.

Table 7 Set Up Tips

Function

Displaying Groups

Displaying Functions

Scrolling

Changing values quickly

Exiting Set Up mode

Timing out from

Set Up mode

Tip

Use the SET UP key to display and scroll through the set up groups. The group titles are listed in the order that they appear on the actuator display.

Use the FUNCTION key to display the individual function parameters under each set up group. The prompts are listed in the order of their appearance in each group. See Tables 8 through 19.

Pressing and holding the SET UP key will scroll through the set up groups. However, when any set up group is displayed, you can scroll through the set up groups twice as fast using the or key. When in any set up group, hold the FUNCTION key in to scroll through the prompts within that group.

When changing the value of a parameter, you can adjust a more significant digit in the upper display by holding in one key or and pressing the other or at the same time.

• The adjustment will move one digit to the left.

• Press the key again and you will move one more digit to the left.

To exit Set Up mode, press the DISPLAY key.

This returns the display to the same state it was in immediately preceding entry into the Set Up mode.

If you are in Set Up (configuration) mode and do not press any keys for thirty seconds, the actuator display will time out and revert to the mode and display that was being used prior to entry into Set Up mode.


7/08

33


Set Up Groups

Set Up Groups

Pressing the SET UP key on the keypad provides access to the various set up groups and allows you to set up operating parameters, (such as input types and alarms), calibrate the actuator’s inputs and outputs, set communications, and check actuator status. Table 8 on the next page lists the set up groups that are available by using the SET UP and FUNCTION keys on the keypad.

Table 8 Set Up Groups

Set Up Group Title

SET

INPUT

Pressing the FUNCTION Key Allows You to…

Select and set various parameters associated with the input signal to the actuator.

For Details, See

Table 10

SET

RELAYn

n

= 1, 2, 3, or 4

Select relay functions. NOTE: Set Relay groups will show on display only if relays are installed in the actuator.

Select the output signal type of the actuator.

Table 13

Table 15

SET

CUROUT

SET

COMM

Select communication parameters for remote control of actuator when connected to a SCADA system.

Table 16

SET

DIGINP

Select the parameters for external digital input states.

Table 17

Select and set parameters for the local display.

Table 18

SET

DISPLA

CAL

INPUT

Calibrate input zero and span values.

Calibration

Procedure,

Table 25

CAL

MOTOR

Calibrate zero and span values for motor operation.

ATTENTION

When calibrating the motor to a short stroke range, you must reset the end-of-travel limit switches. See

Setting End-of-Travel Limit Switches.

Calibrate actuator output.

Calibration

Procedure,

Table 26

CAL

CURENT

Calibration

Procedure,

Table 27

SET

LOCK

READ

STATUS

Set or change security password. Enable or disable security access to set up parameters and calibration set up.

Display operating and alarm status. Display self-test diagnostic results.

Table 19

Table 20

SET

DRVINF

Display and/or set various parameters specific to the actuator.

Table 21


7/08


Set Up Groups

SET

MAINT

CAL

POSOUT

Display various operating statistics. Reset accumulated operating statistics

Use the display as an indicator, (in this case a voltmeter) so you can verify that the position sensor is operating properly.

Table 22

Table 23


7/08

35


Set Up Procedure

Set Up Procedure

Each of the set up groups and their functions are either pre-configured at the factory or set to their default values. Tables 8 through 19 list and describe the options available in each set up group. The following procedure shows you the key press sequence to access any set up group or any associated Function parameter. Make sure lock set up group “LOCK” function is set to “NONE” or “CAL.” Also some parameters require that you enter a security password before you access or change the parameter.

You can use this procedure to access the set up groups and select all parameters.

Step

1

2

3

4

Operation

Enter Set Up Mode

Select any Set Up

Group

Select a Function

Parameter

Select other function parameters

Table 9 Set Up Procedure Using Display and Keypad

Press

SET UP

SET UP

FUNCTION

FUNCTION

Result

Upper Display

= SET

Lets you know you are in the set up mode and a set up group title is being displayed in the lower display.

Lower Display

=

INPUT

This is the first set up group you see when you press SET UP.

Successive presses of the SET UP key will display the other set up group titles as listed in Table 8Error! Reference source not

found.

.

You can also use the or keys to scroll through the set up groups in both directions.

Stop at the set up group title that describes the group of parameters you want to configure. Then proceed to the next step.

Upper Display

4-20

Shows the current value or selection for the function prompt in the selected set up group.

Lower Display

IN TYP set up group.

Shows the first function prompt within the selected

Example display shows Input group function prompt “IN TYP” and the selection.

Successive presses of the FUNCTION key will sequentially display the other function prompts of the selected set up group.

Stop at the function prompt that you want to change, and then proceed to the next step.


7/08


Set Up Procedure

Step

5

Operation

Change the Value or Selection

6

7

Enter Value or

Selection

Exit Set Up mode

Press

or

FUNCTION

or

SET UP

DISPLAY

Result

These keys increase or decrease the value, or display the next available selection for the selected function prompt.

See Table 7, Set Up Tips for instructions to increase or decrease a value quickly.

Change the value or selection to meet your needs.

NOTE: If the display flashes, you are trying to make an unacceptable entry, or the value on the display is at its range limit. The display may also show “KEYERR” (Key error).

This key selects another function prompt.

This key selects another set up group.

NOTE: Pressing either key will cause the previously selected value or selection to be entered into memory.

Exits set up mode and returns actuator to the same state it was in immediately preceding entry into the set up mode. Any changes you have made are stored in memory.

If you do not press any keys for 30 seconds, the display times out and reverts to the mode and display shown prior to entering the set up mode.


7/08

37


Configuration Prompt Hierarchy

Configuration Prompt Hierarchy

IN TYP INP HI INP LO FILTYP Direct Dband FSTYPH

CHAR CUSTOM X0 VAL

RTYPny Rny VAL Rny E* Rny HL RTYPny Rny VAL Rny E*

Rny HL RLYnHY

COMM ADDRES BAUD XmtDLY DBLBYT

DIGINP EndPos

DECMAL EUNITS UNITS

LOCK MAENAB

RAMTST SEETST CFGTST CALTST

VERSON SPEED POWER ROTATE

TEMP

RL2CNT

TEMPHI TEMPLO ACSTAL STARTS RL1CNT

RL3CNT RL4CNT REGN0 REGN9 TOTDEG

DATSAV PASSWD MANRST LD CAL


7/08


Input Set Up Group

Input Set Up Group

Table 10 lists the parameters and selections available when the SET INPUT group is selected.

On the keypad and local display:

• Press the SET UP key to enter the Input Set Up group.

• Press the FUNCTION key to scroll through the prompts listed in the set up group.

• Press the or keys to view selections or change range settings.

Table 10 Input Set Up Group Parameters

Actuator Lower

Display

Prompt

IN TYP

Note: I

f input type from model selection guide is:

0/4-20mA, 0/1-

5Vdc, 0-10Vdc

IN TYP

INP HI

INP LO

Selections or

Range of Setting

4-20

0-20

1-5V

0-5V

0-10

R_SP

S_90

10.0 to 100

default = 100

0.0 to 90.0

default = 0.0

Parameter Definition/PDA HercuLink Prompt

INPUT ACTUATION TYPE

— This selection specifies the signal type and range you are going to use for the actuator input. Be sure that the values configured for the high and low range, alarm setpoint, etc. are within the measuring range for the selected signal range.

4 to 20 mA

0 to 20 mA

1 to 5 Volts dc

0 to 5 Volts dc

0 to 10 Volts dc

Remote Setpoint

(via communications)

NOTE: Changing the Input Actuation Type will restore the actuator calibration to its factory values.

Series 90 –

0 to 135 ohms.

Note: If input type from model selection guide is: Series 90 control

INPUT HIGH RANGE VALUE

in % is displayed.

NOTE: When Input Type (R_SP or S_90) is selected, Input

Hi is not configurable.

INPUT LOW RANGE VALUE

in % is displayed.


Hi is not configurable.


7/08

39


Input Set Up Group

Actuator Lower

Display

Prompt

FILTYP

Selections or


NONE

SPIK

S+LP

LPAS

default = LPAS

LPFILT *

Direct

Dband

FSFTYPH

FsFVALH *

0 to 50.00

(in seconds)

default = 0.5

CCW

CW

default = CCW

0.2

to 5.0

(in percent of span)

default = 0.5

LAST

UP

DOWN

USER

default = UP

0

to 100%

default = 100


INPUT FILTER TYPE

— Allows the selection of a software digital input filter to smooth the input signal.

Spike

— Selects spike filter to remove transients in the input signal when actuator is installed in noisy environments.

Spike plus Low Pass

— Selects spike and low pass filtering.

*

Allows setting of lag time constant for low pass filter.

Low Pass

— Selects low pass filter.

*

Allows setting of lag time constant.


Filter Type = NONE.

LAG TIME CONSTANT

— (Filter Type S+LP or LPAS only)

Allows you to set the first order lag time constant of the low pass filter when selected. Range is from 0 to 50 seconds.

NOTE: When Input Type (R_SP or S_90) is selected, Low

Pass Filter Value is not configurable.

ACTUATOR ROTATION

—This selection determines the direction of rotation of the actuator shaft.

Counterclockwise

rotation

Clockwise

rotation


INPUT DEADBAND

— Specifies an adjustable gap that is the difference between the setpoint value and the value at which the motor energizes. Deadband is set in percent of full span.

FAILSAFEHI TYPE

—Selects the motor position you want the actuator to go to when input signal is above the high end range value.

NOTE: Failsafe condition occurs when the input exceeds its high end range value by 3%,

Last Position

—Actuator motor remains at last position.

Up

—Actuator motor moves to full scale value.

Down

—Actuator motor moves to zero value.

User selected value

—Actuator motor moves to a customerdefined value.

*

Allows setting of failsafehi input value.

FAILSAFEHI INPUT VALUE

—(FailsafeHI Type USER only)

Selects the motor position you want the actuator to go to when input signal is above the high end range value.

Range is from 0 to 100%.


7/08


Input Set Up Group

Actuator Lower

Display

Prompt

FSFTYPL

Selections or


FsFVALL *

LAST

UP

DOWN

USER

default = DOWN

0

to 100%

default = 0

CHAR

CUSTOM

Xn VAL n = 1 - 20

Yn VAL n = 1 - 20

LINR

SQRT

CUST

default = LINR

EQUL

QUIK

USER

default = EQUL

0 to 100 %

0 to 100 %


FAILSAFELO TYPE

—Selects the motor position you want the actuator to go to when input signal is below the low end range value or on loss of input signal.

NOTE: Failsafe condition occurs when the input exceeds its low end range value by 3%, or when the input signal goes to zero. For input types 0 to 20mA, 0 to 5 V, and 0 to 10 V there is no failsafe condition at the zero value.

Last Position

—Actuator motor remains at last position.

Up

—Actuator motor moves to full scale value.

Down

—Actuator motor moves to zero value.

User selected value

—Actuator motor moves to a customerdefined value.

*

Allows setting of failsafelo input value.

FAILSAFELO INPUT VALUE

—(FailsafeLO Type USER only) Selects the motor position you want the actuator to go to when input signal is below the low end range value or on loss of input.

Range is from 0 to 100%.

INPUT CHARACTERIZATION

— Selects a characterization type that causes the actuator to characterize a linear input signal to represent a non-linear input.

Linear

— Provides linear characterization of the input signal.

Square Root

— Provides square root characterizations of the input signal.

Custom

— Custom characterization. Selecting custom allows you to create a twentieth order characterization of input value (x) and associated shaft position (y).

NOTE: Selecting CUST input characterization causes the following prompt CUSTOM to be displayed.

Equal percentage –

Sets the characterization as explained in Equal Percentage Valve Characteristic on page 42.

Values are read-only.

Quick opening

- Sets the characterization as explained in

Quick Opening Valve Characteristic on page 43. Values are read-only.

User-configurable

– Lets you create your own characterization using the following Xn VAL and Yn VAL prompts.

Input Value

— as a percentage of input range. Defaults are in increments of 5%.

Shaft Position Value

— as a percentage of position range.

Defaults are in increments of 5%.


7/08

41


Input Set Up Group

Equal Percentage Valve Characteristic

Table 11 contains values that approximate an equal percentage valve characteristic in the actuator. When the EQUL custom characterization type is selected, the values in Table 11 are automatically loaded into the actuator configuration to produce the characteristic as presented in the graph. The Xn VAL is the input value as a percentage of range and Yn VAL is the characterized output (actuator shaft position) as a percentage of range.

Table 11 Equal Percentage Valve Characteristics

Order

Xn VAL

% of

Range

Yn Val

% of

Range

0 0 0

1 5 0.8

2 10 2.1

100

95

3 15 3.2

90

4 20 4.9

85

80

5 25 6.5

75

6 30 8.4

70

65

60

55

50

15.7

45

10 50 18.7

40

35

11 55 22.6

30

12 60 27.2

25

20

13 65 33.4

15

14 70 40

15 75 46

10

5

0

16 80 53.8

17 85 63.2

18 90 73.7

19 95 86.2

20 100 100

Equal Percentage Valve Characterization

10 20 30 40 50 60 70 80 90 100

Xn VAL - Actual Input


7/08


Input Set Up Group

Quick Opening Valve Characteristic

Table 12 contains values that approximate the characteristic of a quick opening control valve. When the

QUIK custom characterization type is selected, the values in Table 12 are automatically loaded into the actuator configuration to produce the characteristic as presented in the graph. The Xn VAL is the input value as a percentage of range and Yn VAL is the characterized output (actuator shaft position) as a percentage of range.

Table 12 Quick Opening Valve Characteristic

Order

Xn VAL Yn Val

% of

Range

% of

Range

0 0 0

1 5 10

2 10 20

3 15 30

4 20 40

5 25 50

6 30 60

7 35 70

8 40 77

9 45 82

10 50 86

11 55 88

12 60 90

13 65 92

14 70 94

15 75 95

16 80 96

70

65

60

55

50

45

40

35

30

25

20

15

10

5

0

100

95

90

85

80

75

17 85 97.5

18 90 98.5

19 95 99.5

20 100 100

Quick Opening Valve Characteristic

10 20 30 40 50 60 70 80 90 100

Xn VAL - Actual Input


7/08

43


Relays Set Up Group

Relays Set Up Group

ATTENTION

The Relay set up group parameters are accessible only if relay PWAs are installed in the actuator. HercuLine

®

2001 actuators can be equipped with one PWA –for a total of two SPDT relays. Using the Relay set up groups you can program the installed relays to operate in response to various operating conditions.

Table 13 lists the parameters and selections available when the SET RELAYn group is selected.

Table 13 Relay Set Up Group Parameters

Actuator Lower

Display

Prompt

Selections or


Parameter Definition/PDA HercuLink

®

Prompt

RTYPny

n

= 1, 2, 3, or 4

y

= 1 or 2

NONE

InPR

PosR

DEV

ULim

LLim

T Hi

T Lo

STRT

STAL

MAN

PWRF

FsFA

PosF

DiGI

TDEG

default = InPR and

NONE

X1

X10k

default = X1

RELAY TYPE

— Selects the relay number and the relay activation type. See Table 14 Relay Type Descriptions.

Input Range

— Upper / lower limits of input signal exceeded

Position Range

— Upper / lower limits of motor position exceeded

Deviation

— Deviation from input exceeded

Upper Limit Travel

— Same as PosR for upper limit

Lower Limit Travel

— Same as PosR for lower limit

Temperature High

— High temperature limit exceeded

Temperature Low

— Low temperature limit exceeded

Starts

— Motor starts limit exceeded. Allows setting of multiplier value.

Stalled

— Motor position does not follow input

Manual

— Actuator is set to manual mode

Power Up Test Failure

— Failure of any power up diagnostic

Failsafe Alarm

— Failsafe condition detected

Position Sensor Signal Failure

— position output out of valid range

Digital Input

— Digital input closure

Total Degrees

— total degrees traveled. Allows setting of multiplier value.

RnyE*

RnyVAL

n

= 1, 2, 3, or 4

y

= 1 or 2

Rny HL

n

= 1, 2, 3, or 4

y

= 1 or 2

RLYnHY

n

= 1, 2, 3, or 4

0.0 to 100.0

HI

LO

0.0 to 100.0

(in percent)

n

is the relay number, y is the relay contact.

MULTIPLIER

— (Relay Types STRT and TDEG only)

Selects the multiplier for the number limit of motor starts and total degrees traveled before the relay is activated. Multiplier specifies the value on display as times one (X1) or times ten thousand (X10k).

RELAY VALUE

— Sets numerical value of limit where relay trips (energizes). Units are determined by the relay type selection. See Table 14 Relay Type Descriptions for units.

RELAY HIGH/LOW

— Sets relay trip point to high or low limit.

RELAY HYSTERESIS

— 0.0 to 100.0% of span or full output.

NOTE: Relay Hysteresis parameter is accessible only if appropriate relay type is selected.


7/08


Relays Set Up Group

When this Relay Type is selected…

(RTYP)

Input Range

Position Range

Deviation

Upper Limit Travel

Lower Limit Travel

Temperature High

Temperature Low

Starts

Stall

Manual Mode

Power Up Test Failure

Failsafe

Position Sensor Failure

Digital Input

Total Degrees

Table 14 Relay Type Descriptions

The Relay can be set up to indicate …

The upper / lower limits of the input signal have been exceeded.

Relay value parameter defines range limits and units are in percent of full span.

Upper / lower limits of motor position have been exceeded.

Relay value parameter defines range limits and units are in either percent of span or degrees of rotation. See “Relay Examples “for setting range limits.

Motor position has exceeded deviation limit from input. (Deviation is defined as: setpoint – motor position = Deviation)

Relay value parameter defines limits and units are in percent of span.

See “Relay Examples” for setting deviation limit.

The motor position has exceeded the upper limit of travel.

(Same as Position Range.)

Relay value parameter defines limits and units are in degrees of rotation or percent of span. See “Relay Examples” for setting upper limit with hysteresis.

The motor position has exceeded the lower limit of travel.

(Same as Position Range.)

Relay value parameter defines limits and units are in degrees of rotation or percent of span.

The high temperature limit of the actuator has been exceeded. Relay value parameter defines temperature limits and units are in either degrees C or degrees F.

(Temperature units are defined in the UNITS setting of the DISPLA set up group.)

The low temperature limit of the actuator has been exceeded. Relay value parameter defines temperature limits and units are in either degrees C or degrees F.

(Temperature units are defined in the UNITS setting of the DISPLA set up group.)

The accumulated motor starts have exceeded the limit. Relay value parameter defines the limit. See “Relay Examples” for setting motor starts limit. Range is from 10 to 99,990,000.

The motor is in a stall condition.

The actuator is in manual mode.

A failure of any one of the power up test diagnostics. See READ STATUS set up group.

The actuator is in failsafe. (input signal loss or input signal out of valid range)

The potentiometer or non-contact sensor output is out of range or has failed.

The digital input closure.

The total degrees traveled.


7/08

45


Relays Set Up Group

Relay connector #1

Relay connector #2

Relay connector #3

Relay connector #4

Figure 22 Relay connectors

Relay Examples

Relay Type - Position Range

Selecting PosR relay type, you can cause the relay to energize when the actuator motor travels below 20% of range and above 80% of range. Note in the example below that Relay 1 is set up to provide two trip points. The first trip point (R11VAL) causes the relay to energize when the motor travels above 80%, the second trip point (R12VAL) is set so the relay energizes when the motor travels below 20%.

Set Up Group

SET RELAY1

Parameter

RTYP11

Value

PosR

The figure below shows the resulting action.

Motor

Position

0%

17

20%

18

Closed

Open

80%

17

100%

Closed

18

RELAY 1

Normally Open


7/08


Relays Set Up Group

Relay Type - Deviation

Setting up a relay to alarm (energize) when the motor position deviates 10% (+ or -) from the actuator setpoint can be set up as follows.

Set Up Group

SET RELAY1

Parameter

RTYP11

Value

DEV

The resulting action is shown below.

Motor

Position

0%

-10%

Input

50%

+10%

Closed

Open

RELAY n

Normally Open

Closed

100%


7/08

47


Relays Set Up Group

Relay Type – Upper Limit Travel with Hysteresis

Selecting relay type ULim will cause the relay to energize when the motor position exceeds the upper limit trip point, and can be set up as follows. Note that relay hysteresis parameter (RLY1HY) value is set to 10, which is 10% of range. This means that when the relay is energized, due to the motor position exceeding the upper limit value, the relay will not de-energize until the motor moves to 10% below the trip point.

Set Up Group

SET RELAY2

Parameter

RTYP21

Value

ULim

Motor

Position

0%

RELAY n

Normally Open

60%H y s

Open

I s s r e t e

70%

Closed

100%

Motor

Position

0%

RELAY n

Normally Open

60%

Open

I s r e s t s

H y e

70%

Closed

100%

Relay Type – Motor Starts

Selecting relay type STRT will cause the relay to trip when the number of motor starts exceeds the selected limit. The motor starts value is stored as one of the maintenance group statistics. This example sets the motor starts limit at 200,000 for Relay 1.

Set Up Group

SET RELAY1

Parameter

RTYP11

Value

STRT

The resulting action is that Relay 1 will trip when the number of accumulated motor starts in the maintenance group exceeds 200,000.


7/08


Current Out Set Up Group

Current Out Set Up Group

Table 15 lists the parameters and selections available for the SET CUROUT group.

Table 15 Current Out Set Up Group Parameters

Parameter Definition/PDA HercuLink Prompt Actuator Lower

Display

Prompt

CUROUT

Note

: If output type from model selection guide is:

0/4-20mA, 0/1-

5Vdc

CUROUT

Note


Slidewire

Emulation

CUROUT

Note


None

Selections or


4 – 20

0 – 20

1 – 5V

0 – 5V

SW E

NONE

OUTPUT SIGNAL RANGE

— Selects the signal output range.

4 to 20 mA

0 to 20 mA

1 to 5 Volts (250 ohm resistor required)

0 to 5 Volts (250 ohm resistor required)

Slidewire Emulation

No current output configured.


7/08

49


Communications Set Up Group

Communications Set Up Group

Table 16 lists the parameters and selections available for the SET COMM group.

Table 16 Communications Set Up Group Parameters

Actuator Lower

Display

Prompt

COMM

Selections or



ADDRES

BAUD

DIS

MODB

HART

1 to 99

default = 1

COMMUNICATONS PARAMETERS

— Disables or enables parameter displays for Modbus communciations set up.

Disabled

— Locks out access to communications displays and parameters.

Modbus

— Allows access to the communication displays and settings for the parameters listed below.

HART

– selects HART as the communications protocol

DEVICE ADDRESS

— Selects device address when used in a Modbus communications loop. Select an address that is unique to other devices on the communications link.

BAUD RATE

— Selects the speed of data transfer. All equipment on the link must be set to match the host setting.

XmtDLY

DBLBYT

2400

4800

9600

19.2k

default = 19.2k

NONE

10ms

20ms

30ms

40ms

50ms

default = 20ms

FP B

FPBB

FP L

FPLB

default = FP B

RESPONSE DELAY

— Selects the time delay (in milliseconds) before a response to a query is transmitted.

FLOATING POINT DATA FORMAT

— Selects the format for transferring floating point data.

Byte Order

Floating Point Big Endian format

—

Floating Point Big Endian format

with byte-swapped—

Floating Point Little Endian format

—

Floating Point Little Endian format

with byte-swapped—

0 1 2 3

1 0 3 2

3 2 1 0

2 3 0 1


7/08


Digital Input Set Up Group

Digital Input Set Up Group

Table 17 lists the parameters and selections availible for the SET DIGINP group.

Actuator Lower

Display

Prompt

DIGINP

Table 17 Digital Input Set Up Group Parameters

Selections or



®

Prompt

EndPos

NONE

UP

DOWN

USER

default = UP

0 – 100

(in percent)

Digital Input State

— Selects the position of the actuator in response to a digital input signal (contact closure).

None

— No action by the actuator.

Up

— Actuator motor moves to full scale value.

Down

— Actuator motor moves to zero value.

User

selected value— Actuator motor moves to a customer-selected value.

* Allows setting of End Position Value.

END POSITION VALUE

— (DIGINP USER only) Selects the motor position you want the actuator to go to when digital input signal present (contact closure).


7/08

51


Display Set Up Group

Display Set Up Group

Table 18 lists the parameters and selections availible for the SET DISPLAY group.

Actuator Lower

Display

Prompt

DECMAL

Table 18 Display Set Up Group Parameters

Selections or



®

Prompt

EUNITS

UNITS

8888

888.8

default = 8888

PCNT

DEG

default = PCNT

SI

ENGL

default = ENGL

DECIMAL POINT LOCATION

— This selection determines where the decimal point appears in the display.

None

One Place

Note: Be sure the selection agrees with the value to be displayed. If display value requires 4 whole digits, the decimal will not show.

UNITS DISPLAY

— Selects the units of the position display.

Percent

— Shows actuator position as a percentage of span.

(0 to 100%)

Degrees

— Shows the actuator position in degrees of rotation. (0 to 150

°) (90°)

DISPLAY UNITS

— Selects standard for unit values for the local display.

SI

— Display will show unit values in international (metric) units. (Temperature in degrees C, Date format: ddmmyy)

English

— Display will show unit values in U.S. units.

(Temperature in degrees F, Date format: mmddyy)


7/08


Lock Set Up Group

Lock Set Up Group

Table 19 lists the parameters and selections available for the SET LOCK group.

Actuator Lower

Display

Prompt

LOCKID

Table 19 Lock Set Up Group Parameters

Selections or



®

Prompt

LOCK

MAENAB

0 to 4095

default = 0

NONE

CAL

CONF

FULL

default = NONE

DIS

ENAB

default = ENAB

PASSWORD LOCK

— 4-digit password can be selected to provide security access to calibration information, set up parameters and supervisory functions. Password can be a number from 0 to 4095.

LOCK OUT FEATURE

— Selects lockout security for calibration and supervisory functions, and set up groups.

None

— No lockout of any calibration or set up groups. You select and change set up group values, and perform field calibration.

Calibration

— Lockout for calibration groups SET CALINP,

SET CALMTR, SET CALOUT and CAL POSOUT only. You can select and change set up group values.

Configuration

— Lockout for calibration groups and set up group configuration. You can only scroll through and view set up group values.

Full

— Lockout for calibration and all set up group values.

Only SET LOCK and READ STATUS groups are accessible.

Manual / Auto

— Allows the ability to lockout mode changes from the front panel.

Disabled

— Disables the front panel auto / manual switch functionality.

Enabled

— Enables the front panel auto / manual switch functionality.


7/08

53


Lock Set Up Group

Set/Change Password

A password is required to disable the ability to readily change features of the actuator. Lock out of calibration capability and other supervisory functions can be controlled by using a password. The password can be any number from 0 to 4095. The password is set and/or changed by using the keys on the kepad and the local display. Follow the steps below to change the password.

NOTE: The LOCK parameter must be set to NONE in order to change the password.

Step

1

2

3

Action

Press SET UP key until the display reads SET LOCK.

Press the FUNCTION key until the lower display reads LOCK.

If the prompt in the upper display is flashing, a password is required to change the LOCK type, proceed to step 3.

If the upper display is not flashing and you want to change the LOCK type, proceed to step 5.

If the upper display is not flashing and you want to change the password proceed to step 3.

Press the FUNCTION key until the lower display reads LOCKID.

4

5

The upper display will show 0 (zero). Use the or keys to increment the number to the correct password. See NOTE below on use of keys.

Note: If the password can not be recovered to allow user access, a universal password can be obtained by calling the Honeywell Tactical Assistance center.

Press the FUNCTION key, the lower display should read LOCK. The upper display should not be flashing. If it is repeat steps 3 & 4.

6

Use the or keys to change the LOCK type to the desired selection.

If your not changing the password proceed to step 9.

If your changing the password set the LOCK type to NONE and proceed to step 7.

Press the FUNCTION key until the lower display reads LOCKID.

7

8

The upper display will show 0 (zero). Use the or keys to increment the number to the new password. See NOTE below on use of keys.

9

Press FUNCTION key to view next parameter. Press DISPLAY to exit set up mode.

(LOCK type has now been changed or Password is now set to new value).

NOTE:

When changing the value of the number, you can adjust a more significant digit in the upper display by holding in one key or and pressing the other or at the same time.

The adjustment will move one digit to the left.

Press the key again and you will move one more digit to the left.


7/08


Read Status Set Up Group

Read Status Set Up Group

Table 20 lists the parameters and selections available for the READ STATUS group.

Actuator Lower

Display

Prompt

FAILSF

Table 20 Read Status Set Up Group Parameters

Selections or



®

Prompt

RAMTST

SEETST

CFGTST

CALTST

NO

YES

PASS

FAIL

PASS

FAIL

PASS

FAIL

PASS

FAIL

FAILSAFE

— Read Only. Shows whether actuator in failsafe.

No

— Actuator not in failsafe.

Yes— Actuator in failsafe, see

Troubleshooting (page 105)

RAM TEST DIAGNOSTIC

— Read Only. Shows status of

RAM test diagnostic.

Pass

— Test passed, no errors

Fail— Test failed, see see


SERIAL EEPROM TEST DIAGNOSTIC

— Read Only.

Shows status of serial electrically eraseable PROM test diagnostic.

Pass


Fail— Test failed, see


CONFIGURATION TEST DIAGNOSTIC

— Read Only.

Shows status of Configuration test diagnostic.

Pass




CALIBRATION TEST DIAGNOSTIC

— Read Only. Shows status of Calibration test diagnostic.

Pass





7/08

55


Drive Set Up Group

Drive Set Up Group

Table 21 lists the parameters and selections available for the SET DRVINF group.

Actuator Lower

Display

Prompt

VERSON

Table 21 Drive Set Up Group Parameters

Selections or



®

Prompt

SPEED

(150

° @ 60hz)

SPEED

(90

° @ 60hz)

SPEED

(150

° @ 50hz)

SPEED

(90

° @ 50hz)

POWER

ROTATE

TAG

DMFG

nnnn

FIRMWARE VERSION

— Read Only. Displays the firmware version currently in use by the actuator’s CPU.

6 S

12 S

25 S

50 S

75 S

STROKE SPEED

— Read Only. The speed is the number of seconds it takes for the actuator shaft to move its full range of travel.

3.2 S

7.2 S

15 S

30 S

45 S

STROKE SPEED


7.5 S

15 S

30 S

60 S

90 S

STROKE SPEED


4.5 S

9 S

18 S

36 S

54 S

STROKE SPEED


1206

1205

2206

2205

90

150

nnnnnn

mmddyy *

or

ddmmyy

POWER INPUT VOLTAGE AND FREQUENCY

— Read

Only.

Selects the power input voltage and line frequency of the actuator.

1206

— 120Volts, 60Hz

1205

— 120Volts, 50Hz

2206

— 220Volts, 60Hz

2205

— 220Volts, 50Hz

ROTATION

— Indicates the factory calibrated degrees of rotation.

90

— Factory calibrated for 90 degrees of rotation.

150

— Factory calibrated for 150 degrees of rotation.

TAG NAME

— Selects the tag name or identifier of the actuator. Up to 6 alphanumeric characters. See “Set Tag

Nam

e” on next page.

MANUFACTURING DATE

— Read Only. Displays date code of manufacture for actuator.


7/08


Drive Set Up Group

Actuator Lower

Display

Prompt

Selections or



®

Prompt

LREP

mmddyy *

or

ddmmyy

DATE OF LAST REPAIR

of last repair.

— Factory set only. Displays date

LCAL mmddyy *

or

ddmmyy

DATE OF LAST FACTORY CALIBRATION

only.

— Factory set

Displays date of last factory calibration

REPTYP REPAIR TYPE

— Factory set only. Displays a repair code to identify the type of repair service previously performed.

NONE

01

02

03

04

05

06

07

08

09

10

11

12

13

None

Future

Non-contact Sensor

Main CPU PWA repair

Motor service

Power Distribution PWA service

Switch repair

Relay service

Gear service

Service to repair water damage

Service to repair damage caused by heat

Service to repair due to over-voltage damage

Actuator reconfigured

Warranty Repair

*

NOTE: Date format is set by the UNITS parameter. See SET DISPLA set up group.


7/08

57


Drive Set Up Group

Set Tag Name

The actuator tag name can be an alphanumeric name up to six characters. The tag name is set by using the keys on the keypad and the local display. Follow the steps below to set the tag name.

Step

1

2

3

4

5

6

7

Action

Press SET UP key until the display reads SET DRVINF.

Press the FUNCTION key until the upper display reads TAG.

The lower display contains six digits. A decimal point will be flashing at the leftmost digit for approximately three seconds. Then the decimal point shifts to the right and flashes for three seconds before shifting again to the right. This pattern repeats continuously.

Set the digit to the left of the flashing decimal point. Use the or keys to scroll through the character set of 0 through 9, the letters ‘a’ through ‘z’ and the letters ‘A’ through ‘Z’ . Scroll through until the desired character is displayed.

Wait for the decimal point to shift to the right and then scroll through using the or keys until the next character is displayed.

Repeat for each character of the tag until the complete tag name is displayed.

Press the FUNCTION key to go to the next parameter, or press DISPLAY to exit set up mode.


7/08


Maintenance Set Up Group

Maintenance Set Up Group

The Maintenance set up group consists of information about actuator operation accumulated through time.

This information (or maintenance statistics) can be used to evaluate actuator operation and determine predicted or scheduled maintenance periods. Table 22 lists the parameters and selections available for the

SET MAINTENANCE group.

Please note that maintenance statistics are written to the EEPROM every 8 hours. Therefore the statistics are saved in the event of a power interruption.

Actuator Lower

Display

Prompt

TEMP

TEMPHI

TEMPLO

hh:mm:ss †

STARTS

RLnCNT

n

= 1, 2, 3 or 4

REGNn

n

= 0 to 9

TOTDEG

Table 22 Maintenance Set Up Group Parameters

Selections or


nnnn F *

nnnn F *

nnnn F *

ACST †

nnnn nnnn nnnn nnnn


®

Prompt

PDA users: The prompts are organized differently on your PDA’s

HercuLink ® software. Grayed prompts are under Configuration, Maintenance. Non-grayed prompts are under Maintenance.

ACTUATOR TEMPERATURE

— Read Only. Displays the current internal temperature of the actuator.

HIGH TEMPERATURE LIMIT

— Displays the high temperature limit of the internal actuator temperature since it was last reset.

LOW TEMPERATURE LIMIT

— Displays the low temperature limit of the internal actuator temperature since it was last reset.

ACCUMULATED STALL TIME

— Displays the accumulated stall time of the actuator motor since it was last reset.

ACCUMULATED MOTOR STARTS

— Displays the accumulated motor starts since it was last reset. Multiply displayed value times 10

5

to get actual value. Range is 0 to

999,900,000.

RELAY CYCLE COUNTS

— Displays the accumulated cycle counts of a relay since it was last reset. One relay cycle is when a relay is energized and deenergized. Multiply displayed value times 10

5

999,900,000. to get actual value. Range is 0 to

ACCUMULATED MOTOR STARTS

— Displays the accumulated motor starts in the 1 st

10% of motor span since it was last reset. See

Regions of Motor Travel (page 62). Multiply displayed value times 10

5 to get actual value. Range is 0 to 999,900,000.

TOTAL DEGREES OF MOTOR TRAVEL

— Displays the total number of degrees of motor travel since it was last reset. Multiply displayed value times 10

5

Range is 0 to 999,900,000. to get actual value.


7/08

59


Maintenance Set Up Group

Actuator Lower

Display

Prompt

DATSAV

PASSWRD

MANRST

Selections or


DIS

ENAB nnnn

NONE

STAL

STRT

REGNn

n

= 0 to 9

TEMP

TDEG

RELn

n

= 1, 2, 3 or 4

ALL


®

Prompt



MAINTENANCE DATA FORCED SAVE

— Allows you to manually force a save of the current maintenance data values.

DISABLE

— Forced data save is disabled.

ENABLE

— Forced data save is enabled.

PASSWORD

— If a password has been activated, then a 4digit password is required to enable any of the functions below.

NOTE: Password is set (or changed) from the Lock set up group.

MAINTENANCE STATISTIC RESET

— Allows reset of the following maintenance statistics:

None

— No reset of maintenance statisitics

Stall

— Resets accumulated stall time to zero.

Motor Starts

— Resets the accumulated motor start counter to zero.

Motor Starts in the Region

— Resets the selected motor span region counter to zero.

Temperature Statistics

— Resets the high / low temperature limit statistics.

Total Degrees

— Resets the total degrees of motor travel to zero.

Relay Counts

— Resets the selected accumulated relay cycle counter to zero.

All

— Resets all maintenance statistics to zero.

SYST

— Enables the system restart function.

SYST

default = NONE


7/08


Actuator Lower

Display

Prompt

LD CAL

Selections or


NONE

INP

MTR

COUT

ALL

POS


®

Prompt



RESTORE CALIBRATION TYPE

— Allows you to restore a calbration value to its factory calibration.

Input

— Restores input calibration to the factory calibration for the current configured input type.

Motor

— Restores motor calibration to the factory calibration.

Output

— Restores actuator output calibration to the factory calibration for the current configured output type.

All

— Restores input (for the type configured), motor and output (for the type configured) calibration to the factory calibration.

POS

— Allows a position sensor field calibration to be stored as a factory calibration. This is to be used when a sensor is replaced in the field. See “Calibrate POS Output”.

default = NONE

LD CFG DIS

ENAB

RESTORE DEFAULT FACTORY CONFIGURATION

—

Allows you to restore the factory default configuration.

DIS

— Restore disabled.

ENAB

— Restore enabled.

default = DIS

RESTRT DIS

— Allows you to force the system to restart.

ENAB

DIS

— Restart disabled.

ENAB

— Restart enabled.

default = DIS

Note: The MANRST function must be set to SYST.

* Temperature units are displayed in degrees C or F, and are set by the UNITS parameter. See SET

DISPLA set up group.

† Note that the upper display contains the parameter name and the lower display contains the value.

This is to allow for the display of hours: minutes: seconds.


7/08

61


Regions of Motor Travel

Regions of Motor Travel

The full span of motor travel can be 90

° or 150° rotation. The span is divided into 10 regions of motor travel as shown in Figure 23 (regions are numbered 0 through 9). Maintenance statistics are accumulated on the total number of motor starts, as well as the total number of motor starts that occur in each region of travel. The statistics can be accessed in the maintenance set up group. The counts can also be reset to zero if desired. See the Maintenance Set Up Group for more information. The regions of travel are determined by the full span motor travel (90

° or 150° rotation). If the actuator is set up to operate in a smaller range, for example between 40% and 80% of full span, the maintenance statistics will show motor starts only in regions 4 through 7.

Percent of Span

0% 20% 40% 60% 80% 100%

Region of Travel

0 1 2 3 4 5 6 7 8 9

0o 30o 60o 90o

Degrees of Rotation

Pe rc en t of S pa n

0% 20% 4 0% 60% 8 0% 100%

Regio n of Trave l

0 1 2 3 4 5 6 7 8 9

0o

De gr ee s of R ot at io n

30 o 60 o

Figure 23 Regions of Motor Travel

150 o


7/08


CAL POSOUT Group

CAL POSOUT Group

The CAL POSOUT group is used to verify that the position sensor is operating and adjusted properly. This group allows the local display to indicate the output voltage of the position sensor. This display is used when verifying the POS sensor is operating and that it is properly calibrated. Table 23 shows the selections available for the CAL POSOUT group.

Actuator Lower

Display

Prompt

CALPOS

Table 23 CAL POSOUT Group Parameters

Selections or



n.nnn POSITION SENSOR OUTPUT

— Read Only. Displays the output voltage of the position sensor

To access the display…

Press

SETUP until you see

Upper Display

Lower Display

=

=

or key

Lower Display

=

Upper Display

Lower Display

=

=

Upper Display

=

Lower Display

=

Result

CAL

POSOUT

DIS

CALPOS

BEGN

CALPOS

n.nnn

(sensor output in volts)

POSOUT


7/08

63


Auto - Manual Drive Switch

Auto - Manual Drive Switch

The Auto - Manual switch is located on the side of the actuator case below the handwheel. The switch allows manual mode control of the actuator motor for set up, calibration and troubleshooting.

Figure 24 shows an illustration of the Auto - Manual switch and Table 24 describes the switch settings.

The Auto - Manual Drive switch setting overrides all input signals (analog signal and remote setpoint) and local display mode settings. When not in auto the manual LED will flash every second.

CCW

MANUAL

OFF

CW

OFF

A

U

T

O

AUTO - MANUAL DRIVE

Figure 24 Auto - Manual Switch

Switch Setting

AUTO

CCW

CW

OFF

Table 24 Auto - Manual Switch Functions

Motor Drive Control

Actuator moves according to signal input and set up configuration.

Actuator moves to the fully counterclockwise position.

Actuator moves to the fully clockwise position.

Actuator is idle.


7/08


Calibration

Calibration

Calibration of the HercuLine

®

2000 Series Actuator may consist of calibrating the motor circuit that positions the actuator with 0/4-20mA input signal, calibrating the potentiometer or non-contact sensor, and calibrating the slidewire emulation output or the 0/4-20mA output signal. Typically, only a motor calibration is required for installation.

Calibration is performed by connecting test equipment to the input terminals or output terminals and then using the keypad and display to step through the calibration group functions.

ATTENTION

Input calibration and output calibrations are performed at the factory and may not be necessary. Normally, you may only need to perform Calibrate Motor.

Only qualified personnel should perform calibration.

High voltages exist inside the actuator case. Do not touch the powered wires inside.

Death or serious injury can occur.

Equipment Needed

The table below lists the equipment you will need to calibrate the HercuLine

®

2000 input and output circuits.

Procedure Equipment Needed

Input Calibration

Output Calibration

•

A calibrated signal source which can provide current (4 to 20 mA) or voltage (0 to 10 V) with an accuracy of 0.02% or better.

•

Two insulated copper leads for connecting the current source to the actuator.

• A digital voltmeter with an accuracy of 0.01% or better.

• A 250 ohm resistor 0.01% tolerance.


7/08

65


Calibration

Calibration Set up

Follow the steps below to set up the test equipment and actuator to verify calibration or perform calibration procedures.

Step

1

2

3

4

5

Action

Determine input type (current or voltage).

Set jumper W2 on main CPU board according to type of signal source. See Figure 27 on page

68 for jumper location.

Connect the copper leads from the signal source to the input terminals of the actuator as shown in Figure 25.

Place signal source output at zero and switch power on.

Connect a 250 ohm resistor across the Output terminals of the actuator and connect the DVM leads to the terminals.

Actuator

Calibrated

Signal

Source

+

-

Terminal Block

Input

5 4

+

Output

+

Digital

Voltmeter

+ -

Internal 250 ohm resistor settable through

Jumper W2

Current

Voltage

250 ohm resistor

(supplied)

Figure 25 Calibration Wiring Connections (non-slidewire emulation)


7/08


Calibration

Actuator

Digital

Voltmeter

+ Calibrated

Signal

Source

+

-

Terminal Block

Input

5 4

+

Output

2 1 3

+

FB

Internal 250 ohm resistor settable through

Jumper W2

Current

Voltage

Figure 26 Calibration Wiring Connections (slidewire emulation)

Power

Supply

1-18 VDC

+ -


7/08

67


Calibration

Jumper W2

Figure 27 Jumper Location on CPU PWA

Calibrate Input

The HercuLine

®

2001/2002 actuator accepts a variety of signal inputs.

1. 0 to 20 mA, or 4 to 20 mA

2. 0 to 5 Volts,1 to 5 Volts, or 0 to 10 Volts

The input type is selected through the Input set up group using the local keypad.

Refer to Figure 25 for the wiring connections and follow the procedure in Table 25 to calibrate the input circuit of the HercuLine

®

2001/2002 actuator.

ATTENTION

For an input calibration to be saved, you must complete the procedure. The calibration will not be saved if you exit without completing the steps of the procedure.

To exit calibation mode, press DISPLAY or SETUP keys.


7/08


Calibration

Table 25 Input Calibration Procedure

Step

1

Operation

Enter Calibration

Mode

2

3

Calibrate Zero (0%)

Calibrate Span

(100%)

Press

SETUP until you see

or key

FUNCTION

FUNCTION

Upper Display

Lower Display

=

=

Lower Display

=

Upper Display

=

Lower Display

=

Result

CAL

INPUT

DIS

CAL IN

BEGN

CAL IN

Upper Display

=

Lower Display

=

APLY

INZERO

•

Adjust the signal source to an output value equal to 0% range value.

•

Wait 5 seconds, then go to step 3.

Upper Display

=

Lower Display

=

APLY

INSPAN

• Adjust the signal source to an output value equal to 100% range value.

• Wait 5 seconds, then go to step 4.

4

calibration is complete.

NOTE: The display will automatically go to the CAL MOTOR set up display. See Table 26. You may also exit calibation mode by pressing the DISPLAY or SETUP keys.

ATTENTION:

When calibrating the motor to a short stroke range, you must reset the end-of-travel limit switches. See Setting End-of-Travel

Limit Switches.


7/08

69


Calibration

Calibrate Motor

Use the procedure in Table 26 to calibrate the actuator motor for 0% and 100% input signal

ATTENTION

For a motor calibration to be saved, you must complete the procedure. The calibration will not be saved if you exit without completing the steps of the procedure.

ATTENTION

When calibrating the motor to a short stroke range, you must reset the end-of-travel limit switches. See Setting End-of-Travel Limit Switches.

Table 26 Motor Calibration Procedure

Step

1

2

3

Operation

Enter Calibration

Mode

Press

SETUP until you see

Upper Display

=

Lower Display

=

Upper Display

=

Lower Display

=

Calibrate Zero (0%)

Calibrate Span

(100%)

Result

CAL

MOTOR

DIS

CALMTR

or key

Upper Display

=

Lower Display

=

FUNCTION

BEGN

CALMTR

Upper Display

=

Lower Display

=

APLY

MTR LO

•

Use the Handwheeel or AUTO/MANUAL switch to manually drive the actuator motor to its low position.

•

Wait 5 seconds, then go to step 3.

FUNCTION

Upper Display

=

Lower Display

=

APLY

MTR HI

• Use the Handwheeel or AUTO/MANUAL switch to manually drive the actuator motor to its high position.

• Wait 5 seconds, then go to step 4.

4

Motor calibration is complete.

NOTE: The display will automatically go to the CAL CURENT set up display. See Table 27. You may also exit calibation mode by pressing the DISPLAY or SETUP keys.


7/08


Calibration

Calibrate Output

HercuLine

®

2001/2002 actuator can be one of three output types:

1. 0 to 20 mA, or 4 to 20 mA output

2. 0 to 5 Volts, or 1 to 5 Volts with 250 ohm range resistor

3. Slidewire emulation.

The output signal range is selected through the Current Out set up group using the keypad and local display.

0/4-20 mA Output

The HercuLine

®

2001/2002 Actuator comes already calibrated from the factory. If it becomes necessary to do a calibration in the field, adjust the output using the procedure in Table 27. Refer to Figure 25 for a diagram to connect a signal source to the actuator input and a DVM to measure actuator output signal.

This procedure provides the steps to calibrate the actuator for a 4 to 20mA output. If you are using another output type, change the procedure accordingly.

ATTENTION

For an output calibration to be saved, you must complete the procedure. The calibration will not be saved if you exit without completing the steps of the procedure.

To exit calibation mode, press DISPLAY or SETUP keys.

Table 27 Output Calibration Procedure

Step

1

Operation

Enter Calibration

Mode

Press

SETUP until you see

Upper Display

=

Lower Display

=

Result

CAL

CUR OUT

DIS

CALOUT

Lower Display

=

or key

Upper Display

=

Lower Display

=

BEGN

CALOUT


7/08

71


Calibration

Step

2

3

Operation

Calibrate Zero (0%)

Calibrate Span

(100%)

Press Result

FUNCTION Upper Display =

Lower Display =

xxx

ZERO

• Read meter connected to actuator output.

or key

• Adjust actuator output to a value equal to 0% output as read from the DVM.

NOTE: Typically for a 4 mA output, the display will show a value of approximately 382. A lower limit value is imposed on the zero output. If the value is 357 or lower, the actuator will not allow you to calibrate the zero output. The value must be larger than 357 for a valid calibration.

FUNCTION

Upper Display

=

Lower Display

=

xxxx

SPAN

• Read meter connected to actuator output.

or key

• Adjust actuator output to a value equal to 100% output as read from the DVM.

• NOTE: Typically for a 20 mA output, the display will show a value of approximately 1887.

4

Output calibration is complete.

Slidewire Emulation

The HercuLine

®

2001/2002 Actuator comes already calibrated from the factory. If it becomes necessary to do a calibrationin the field, adjust the output using the procedure in Table 28. Refer to Figure 26 for a diagram to connect a signal source to the actuator input and a DVM to measure actuator output signal.

ATTENTION

For a slidewire emulation output calibration to be saved, you must complete the procedure.

The calibration will not be saved if you exit without completing the steps of the procedure.

To exit calibration mode, press DISPLAY or SETUP keys.


7/08


Calibration

Table 28 Slidewire Emulation Calibration Procedure

Step

1

2

3

Operation

Enter Calibration

Mode

Press

SETUP until you see

Result

CAL

OUTPUT

Upper Display

=

Lower Display

=

or key

Upper Display

=

Lower Display

=

Calibrate Zero (0%)

Calibrate Span

(100%)

DIS

CALOUT

BEGN

CALOUT

FUNCTION Upper Display =

Lower Display =

xxx

ZERO

xxx = arbitrary number assigned by software

or key

Adjust actuator output voltage using down key until value on

DVM ceases to change, then press up key until value on DVM moves up one digit

FUNCTION

Upper Display

=

Lower Display

=

xxxx

SPAN

xxx = arbitrary number assigned by software

or key Adjust actuator output voltage using key until value on DVM ceases to change, then press down key until value on DVM moves down one digit

FUNCTION

Upper Display

=

Lower Display

=

Calibration for zero and span output values are now stored.

Slidewire Emulation Output Calibration is complete. Read meter connected to actuator output.

Calibrate Position Sensor

ATTENTION

The Position Sensor is factory calibrated. Under normal operation it does not require calibration.

Sensor calibration may be necessary due to any of the following conditions:

•

The sensor output is incorrect,

•

The position sensor in the actuator has been replaced,

•

The position sensor adjustment has been disturbed.

When the position sensor has been replaced (or serviced), you should perform a calibration of the position sensor circuit and then store it as the motor factory calibration. Please note that performing this procedure will destroy any previously stored motor factory calibration values. Table 29 outlines the steps to perform a calibration to the position sensor circuit.


7/08

73


Calibration


Table 29 NCS Position Sensor Calibration Procedure

Step

1

2

3

4

5

6

Action

Remove AC power to the actuator.

Remove the six screws and the top cover from the actuator case. See Figure 2.

Lay extended cover assembly on a flat surface. Remove relay cards if present.


Press SET UP key to access the INPUT set up group.

Press FUNCTION key until the lower display reads Direct.

Press the or keys to set Actuator Rotation direction to CCW.

NOTE: Actuator direction must be set to CCW for this procedure. Direction can be changed after calibration is complete.

Drive the actuator to the 50% position (this refers to the position on the actuator scale for CCW rotation). This should be done manually with the handwheel or with the AUTO - MANUAL switch.

Press SET UP key until the display reads CAL POSOUT.

Press the FUNCTION key until the dispaly reads DIS CALPOS.

7

8

Press the or keys until the lower display reads BEGN CALPOS.

Press FUNCTION key.

The upper display now shows the output of the position sensor in Volts.

Loosen the allen screw in the hub of the NCS spoiler just enough to be able to rotate the spoiler. See Figure 28.

Adjust the NCS spoiler so that the voltage in the local display is 2.500 ± 0.010 volts dc. The allen screw should be almost in a vertical position. The bottom edge of the spoiler should almost be horizontal in relation to the NCS PWA. See Figure 28.

9

Tighten NCS spoiler set screw with an allen wrench, holding spoilers located on each side of the NCS PWA in position.

IMPORTANT

: Spoilers need to be held in position both rotationally and longitudinally along the drive shaft extension. An air gap must be maintained between the surface of the PWA and each spoiler. (Any plastic or paper insulating material may be used to create this gap while positioning the spoilers). Make sure that neither spoiler is touching the sensor PWA when the adjustment is complete.

10

Press DISPLAY key to exit calibration mode.

11

Remove AC power to the actuator. Reinstall relay cards If present.

12

Install a new gasket and replace extended cover. Secure to actuator with screws.

13

Continue with calibration procedure in Table 31.


7/08


Calibration

NCS Spoiler (shown at full

150 degree travel CCW)

Figure 28 Location of NCS Assembly

NCS set screw

NCS PWA

Relay PWA card guides (relay

PWAs removed)


7/08

75


Calibration

Table 30 Potentiometer Position Sensor Calibration Procedure

Step

1

2

3

4

5

6

Action


Remove the six screws and the top cover from the actuator case. See Figure 2.

Lay extended cover assembly on a flat surface. Remove relay cards if present.


Press SET UP key to access the INPUT set up group.

Press FUNCTION key until the lower display reads Direct.

Press the or keys to set Actuator Rotation direction to CCW.

NOTE: Actuator direction must be set to CCW for this procedure. Direction can be changed after calibration is complete.

Drive the actuator to the 50% position (this refers to the position on the actuator scale for CCW rotation). This should be done manually with the handwheel or with the AUTO - MANUAL switch.

Press SET UP key until the display reads CAL POSOUT.

Press the FUNCTION key until the dispaly reads DIS CALPOS.

7

Press the or keys until the lower display reads BEGN CALPOS.

Press FUNCTION key.

The upper display now shows the output of the position sensor in Volts.

Loosen the set screw at the end of the switch camshaft where the potentiometer connects to the shaft.

8

9

Using pliers, adjust the white plastic knob on the back side of the potentiometer so the voltage in the local display is 2.500 ± 0.010 volts dc.

Tighten set screw with an allen wrench.

10

Press DISPLAY key to exit calibration mode.

11

Remove AC power to the actuator. Reinstall relay cards If present.

12


13

Continue with calibration procedure in Table 31.


7/08


Calibration

Potentiometer position sensor Mounting bracket

Figure 29 Location of potentiometer position sensor

Step

1

2

3

4

Table 31 Load Position Sensor Factory Calibration

Action


Press SET UP key to access the MAINT set up group. Press the FUNCTION key until the display reads LD CAL.

Press the or keys until the display reads POS.

Perform the Calibrate Motor procedure exactly as in Table 26 Motor calibration must be performed for the factory configured full span range (0-100%).

ATTENTION

When calibrating the motor to a short stroke range, you must reset the end-of-travel limit switches. See Setting End-of-Travel Limit Switches.

When motor calibration is complete, the calibration is now stored as the factory calibration of the actuator motor.


7/08

77


Setting End-of-Travel Limit Switches

Setting End-of-Travel Limit Switches

ATTENTION

Referring to Figure 31. The first two cams (starting from the front) are for the 0% and

100% limit switches (Switch #1 and Switch #2) and should not need any adjustments as they are factory set to stop the drive at 0% and 100%. See Figure 30 for limit switch settings.

END OF TRAVEL LIMIT SWITCH S ETTINGS

(FACTORY SET A T 0% AND 100%)

0%

100%

LEFT HAND

POINTER

SCALE

14

SW#1

8 (SW1 COM)

NC

Clockwise Rotation

9 (SW2 COM)

7

SW#2

5

NC

Counterclockwise Rotation

15

Clockwise and counterclockwise rotation is the direction of the output shaft when facing the end of the shaft. As shown, clockwise rotation of the output shaft activates SW 1 (at 0% on the left hand pointer scale) and CCW rotation activates SW 2 (at 100% on the left hand pointer scale). Terminal numbers are next to the circles.

Figure 30 End of Travel Limit Switch Settings

REFERENCE

An unactuated switch will have its normally closed (NC) contacts closed and its normally open

(NO) contacts open.

An actuated switch will have its NC contacts become open and its NO contacts become closed. Both NC and NO contacts are available at the terminal block. See Figure 8 (page 18) and Figure 9 (page 19).

An unactuated switch has its roller arm in the up position when adjacent to the reduced diameter portion of the cam.

If it becomes necessary to do adjust the limit switch cams in the field, use the procedure given in Table 32.



7/08



Table 32 End-of-Travel Limit Switch Setting Procedure

Step

1

2

3

4

Action


Remove the six screws and the cover from the actuator case. See Figure 2. Lay cover assembly on a flat surface.

Using a flat blade screwdriver in the slots at the edge of the cams, or your finger, rotate the cams until the switches are set. (See Figure 31).

• Rotate the actuator shaft, using the manual handwheel or the auto-manual switch, to the 0% position (this is the 0% for CCW operation using the bottom scale or 100% for CW operation using the top scale). If the actuator is installed on a damper or valve, also make sure that this position is synchronized with the travel of the final control element.

• Rotate the #1 limit switch operating cam to activate at this position. The switch roller arm should go from being in an up, not depressed state, to a depressed state as the cam is rotated in the direction of the shaft rotation going toward the limit position. This will cause the switch to go from NC to NO and turn off the power to the motor when the switch activates. Switch activation may be detected by the clicking sound or with a continuity tester connected to the terminals.

• Rotate the actuator shaft, using the manual handwheel or the auto-manual switch, to the

100% position (this is 100% for CCW operation using the bottom scale or 0% for CW operation using the top scale). If the actuator is installed on a damper or valve, also make sure that this position is synchronized with the travel of the final control element.

• Rotate the #2 limit switch operating cam to activate at this position. The switch roller arm should go from being in an up, not depressed state, to a depressed state as the cam is rotated in the direction of the shaft rotation going toward the limit position. This will cause the switch to go from NC to NO and turn off the power to the motor when the switch activates.

• If optional auxiliary switches were ordered, these switches may also be set at this time. (See

Setting Auxiliary Switches (page 81).

Double check limit switch actuation by first manually driving the actuator to each end of travel and hearing the switch click or by detecting it with a continuity tester. Secondly, drive the actuator to both ends of travel (using the auto/manual switch or by providing minimum and full input signal) and make sure the switches activate and turn off the motor.


7/08

79



ATTENTION

Make sure you do not to set the switches too close to the hard stop.

Relay PWAs

Relay #1

Relay #2

Relay #3

Relay #4

Aux switch #1

Aux switch #2

Aux switch #3

Aux switch #4

End of travel switch #1

(stops CW rotation)

End of travel switch #2

(stops CCW rotation)

Figure 31 Location of End-of-Travel Limit and Auxiliary Switches


7/08


Setting Auxiliary Switches

Setting Auxiliary Switches

ATTENTION

Referring to Figure 31. The first two cams (starting from the front) are for the 0% and

100% end of travel limit switches (Switches #1 and #2) and should not need any adjustments as they are factory set to stop the actuator precisely at 0% and 100%. See

Setting End-of-Travel Limit Switches (page 78).

Additional switch settings should be set so that switch #3 operates in synchronism with switch

#1 (i.e., both activating when the actuator is going in the same direction) and switch #4 to operates in synchronism with switch #2, etc. See Figure 32 for auxiliary switch settings.

LEFT HAND

POINTER SCALE

0% 100%

SW #3

17 (SW3 COM)

18

NO

(SW 6 COM) 26

23 (SW5 COM)

NC

20 (SW4 COM)

16

NC

NO

21

SW #4

19

SW #5

24

NO

NC

22

SW #6

25

NC

NO

27

Figure 32 Auxiliary Switch Settings

If it becomes necessary to do adjust the auxillary switch cams in the field, use the procedure given in Table

33.



7/08

81


Setting Auxiliary Switches

Table 33 Auxiliary Switch Setting Procedure

Step

1

2

3

4

5

6

Action


Remove the six screws and the cover from the actuator case. See Figure 2. Lay cover assembly on a flat surface.

Using a flat blade screwdriver on the slots on edge of cams, or your fingers, rotate the cams until the switches are set. (See Figure 31)

• The auxiliary switches should be set so switches #3 and #5 operate in synchronism with switch #1 (i.e., both activating when the drive is going in the same direction) and set switches #4 and #6 to operate in synchronism with switch #2. See Figure 32 for auxiliary switch settings.

For Switches #3 and #5:

• Rotate the actuator shaft, using the manual handwheel or the auto-manual switch, to the desired low scale position.

• Rotate the #3 switch operating cam to activate at this position. The switch roller arm should go from being in an up, not depressed state, to a depressed state as the cam is rotated in the direction of the shaft rotation going toward the limit position. This will cause the switch to go from NC to NO and turn off the power to the motor when the switch activates. Switch activation may be detected by the clicking sound or with a continuity tester connected to the terminals.

• Repeat for Switch #5 if applicable.

For Switches #4 and #6:

• Rotate the actuator shaft, using the manual handwheel or the auto-manual switch, to the desired up scale position.

• Rotate the #4 switch operating cam to activate at this position. The switch roller arm should go from being in an up, not depressed state, to a depressed state as the cam is rotated in the direction of the shaft rotation going toward the limit position. This will cause the switch to go from NC to NO and turn off the power to the motor when the switch activates.

• Repeat for Switch #6 if applicable.

Double check limit switch actuation by first manually driving the actuator to each end of travel and hearing the switch click or by detecting it with a continuity tester. Secondly, drive the actuator to both ends of travel (using the auto/manual switch or by providing minimum and full input signal) and make sure the switches activate and turn off the motor.


7/08

Start-Up/Operation

Introduction

Start-Up/Operation

Introduction

After the actuator is completely installed, wired, and the preliminary adjustments made, it is advisable to check the operation of the actuator and controlled device before placing it in service. In other words, operate the controlled device and check its direction of travel in response to an increase of the input signal and make sure it is correct for the process. Actuators having the optional auto-manual switch must have the knob set in the

AUTO position.

This section provides a checklist that can be used to do a walk-through with the actuator before it is actually used for control. Other features which may be helpful in understanding actuator operation are also provided.

Power-up Diagnostics

When power is applied to the actuator, the actuator electronics performs a diagnostic routine on various device components. These tests include a:

•

RAM diagnostic (RAMTST),

•

Check of the electrically eraseable PROM (SEETST),

•

Verification that valid parameter values are in the actuator configuration (CFGTST),

•

Verification of valid calibration values (CALTST)

•

Test of the local display and LED indicators (all display segments and LED indicators light simultaneously).

The local display shows the status of the diagnostics as they are completed during power up. TEST DONE is shown on the display when diagnostics are complete and actuator should be in AUTO mode. See Table 20 for more information on the power up diagnostics.

Operations Checklist

To make sure that the actuator is properly installed and set up for your particular application, you should check and verify the following:

•

Verify that the configuration is correct for your application by stepping through all set up groups and checking the setting of all set up parameters.

•

Verify operation of end-of-travel limit switches.

•

Verify operation of auxiliary switches or relay function (if installed).

•

Check operation of AUTO - MANUAL DRIVE switch (if present), by setting the knob to the CW and CCW

- MANUAL positions. The output shaft should rotate in the direction indicated by the knob. The LED indicator on the local display should also indicate the actuator is in manual mode.


7/08

83

Start-Up/Operation

Operating Displays

Operating Displays

Pressing the DISPLAY key cycles the display through a number of operating parameters. Table 34 shows a number of sample displays that can be shown during operation.

Table 34 Typical Operating Displays

Display

0.0

INP

00

OP 0.5

100.0

DE 99.9

0.6

POS

Description

Input

—

Output

—

Upper Display = Shows input value

Lower Display = prompt


Lower Display = Shows output value

Deviation

—


Lower Display = Shows value of deviation of

Position

—

Upper Display = Shows value of position sensor.

Lower Display = prompt

NOTE: Position display will show negative values, if appropriate.

NOTE: When the AUTO/MANUAL key is pressed, placing the actuator in manual mode, the local display mode is forced to the Position display (POS). The Manual L.E.D. indicator should be lit. When the

AUTO/MANUAL key is pressed again, placing the actuator in auto mode, the local display mode is forced to the Output display (OP). The Auto L.E.D. indicator should be lit. Set up parameters can still be accessed.

Motor Stall

The actuator is equipped with a low current motor that prevents against burnout if the motor becomes stalled. A stall condition occurs when the motor position does not follow the input, or if the motor does not reach setpoint within a given period of time.

When the stall condition occurs, a stall alarm is indicated. The actuator sets the STALLED LED indicator ON and also any other alarms or relay contacts that are programmed to close whenever a stall condition is detected.

The motor drive for the indicated direction is shut off approximately 3 minutes after the stall alarm is indicated.

Also, the appropriate CW/CCW LED direction indicator is turned OFF.

The maintenance statistic for accumulated stall time gets updated during the stalled condition.

To reactivate the drive in the stalled direction, change the position of the drive to the opposite direction and set at a point below where the stall originally occurred, then start the drive in the stalled direction.

Note: A stall condition is not detected if a limit end of travel limit switch is activated while the motor is moving toward the setpoint, or if the motor position is within 0.5% of calibrated motor 0% and 100% end points.”


7/08

Start-Up/Operation

Position Sensor Operation

Position Sensor Operation

On HercuLine

®

2000 and HercuLine

®

2001 the potentiometer position sensor is a sealed film pot that is directly coupled to the output shaft. On HercuLine

®

2002 the non-contact sensor (NCS) is inductively coupled to the output shaft of the actuator so that the sensor detects shaft position. The sensor is adjusted at the factory and under normal conditions and requires no adjustment. A simple check can verify that the sensor working properly and that it is in adjustment. Verification of the output is performed by setting the drive motor to its zero, midpoint and 100% positions and observing the output voltage of the sensor. The actuator has a feature that the sensor output voltage can be read from the local display.

Step

1

Drive the motor to 50% position.

Action

2

Press SET UP key on the keyboard until the display reads CAL POSOUT.

Press FUNCTION key until the display reads DIS CALPOS.

Press the or keys until the display reads BEGN CALPOS.

Press the FUNCTION key.

Lower Display

= POSOUT

3

The display should read 2.500 +/– 0.012 Volts for both 90° and 150° operation.

4

Press DISPLAY key and then drive the motor to zero position. Repeat Step 2.

The display should read 1.600 +/– 0.060 Volts for 90° operation; 1.000 +/- 0.060 volts for 150° operation.

5

Press DISPLAY key and then drive the motor to 100% position. Repeat Step 2.

The display should read 3.400 +/– 0.060 Volts for 90° operation; 4.000 +/- 0.060 volts for 150° operation.

6

If the sensor needs adjustment, refer to the “Calibrate Non-Contact Sensor” procedure in Table

29 (page 74).

Remote Setpoint Operation

The HercuLine

®

2001/2002 actuator can be set up to receive a digital input from a remote source. The actuator uses RS485 communications that supports digital Modbus RTU protocol. Press the SET UP key to select the

Input set up group. Change the Input Type to Remote Setpoint (R_SP). Make the necessary connections to terminals 6, 7, 8 on the actuator terminal block. See Figure 33. Communicaton parameters should be set to the same values as the host device. The actuator communication parameters are accessed in the Communications

Set Up group.

There are some restrictions to actuator operation when remote setpoint input is active. In order to provide a bumpless transfer when switching from one input signal type to remote setpoint, the actuator will use the last known analog input value as its setpoint when switching to remote setpoint input operation. No input filtering is active on the input signal to the actuator.


7/08

85

Start-Up/Operation

Remote Setpoint Operation

Actuator

Terminal

Block

6 7 8

9 10

+

-

SHIELD

COM

INP

COM M UNICATION

DIGITAL INPUT

Figure 33 Terminal Block Connections for Modbus Communications


7/08

Maintenance

Introduction

Maintenance

Introduction

There is some basic maintenance that is recommended for the HercuLine

®

2000 Series Actuators. The electronic PWAs within the actuator require no maintenance or servicing under normal conditions.

If there is a problem, refer to information in this section or to Troubleshooting (page 105) .

Basic Maintenance

Position Sensor

Under normal conditions the position sensor does not require maintenance.

Main Gear Lubrication

Under normal operating conditions, the main worm gear should not require maintenance.

Spur Gear Lubrication

Honeywell recommends that during major shutdown periods the spur gears should be inspected and lubricated. Follow the steps in Table 35 to access the spur gear compartment and lubricate the gears if necessary.

Disconnect power before opening the actuator case to inspect the actuator gears. A potentially dangerous pinch hazard exists inside the case if the unit is open while powered.

Table 35 Spur Gear Lubrication Procedure

Step

1

2

3

4

5

6

Action

Remove AC power from actuator.

Remove the six screws and the bottom cover of the actuator case. See Figure 34.

Inspect the final spur gear, the idler gear and motor pinion for excessive wear and adequate lubrication. See Figure 34.

If needed, use Texaco Starplex 2 EP grease, or equivalent and apply lubricant to assure that the gears are adequately protected.

Install a new gasket and replace side cover. Secure to actuator with screws.

Restore actuator to service.


7/08

87

Maintenance

Basic Maintenance

Bottom cover Gears

Idler spur gear

Final output spur gear

Figure 34 Spur Gear Location

Motor pinion gear


7/08

Maintenance

Replacement Procedures

Replacement Procedures

Fuse Replacement

The motor drive circuit contains two fuses. They are located on the power distribution PWA. If it becomes necessary to replace these fuses, follow the procedure in Table 36 and refer to Figure 36 for fuse location.

Disconnect power before opening the actuator case to replace the fuse(s). A potentially lethal shock hazard exists inside the case if the unit is opened while powered.

Table 36 Motor Drive Fuse Replacment Procedure

Step

1

2

3

4

5

6

7

8

9

Action


Remove the 6 screws and the extended cover of the actuator case. See Figure 35.

Lay assembly down on a flat surface.

Remove connectors from CPU and power distribution PWA.

Remove power distribution PWA.

Locate the two fuses on the power distribution PWA. See Figure 36. Carefully remove and replace fuse(s) with Wickmann T1 type 6A 250V, or equivalent (not available from Honeywell).

Reinstall power distribution PWA.

Reconnect connectors to CPU and power distribution PWA.


Relay connector #1

Relay connector #2

Relay connector #3

Relay connector #4

}

}

Relay PWA#1

Relay PWA#2

Power distribution

PWA

CPU connections

Figure 35 Power Distribution PWA and Relay PWA Locations


7/08

89

Maintenance

Replacement Procedures

Power Distribution PWA

Fuses for

Motor Drive

Circuit

Figure 36 Motor Drive Circuit Fuses

Relay PWA Replacement

If a relay PWA needs to be replaced, follow the procedure in Table 37 to access and replace the PWA.

Disconnect power before opening the actuator case. A potentially lethal shock hazard exists inside the case if the unit is opened while powered.

Table 37 Relay PWA Replacement Procedure

Step

1

2

3

4

5

6

7

8

Action


Remove the six screws and the cover of the actuator case. See Figure 35.

Lay assembly down on a flat surface.

Disconnect the wire connector from the relay PWA.

Carefully remove the relay PWA. Pry the locking tabs of the card guides away to unlock the

PWA and slide it out from the card guides.

Install the replacement relay PWA by sliding it into the card guides until it mates with the backplane board. Locking tabs on the card guides will engage to secure the PWA in place.

Plug in wire connector to relay PWA.

Install a new gasket if needed and replace cover. Secure to actuator with screws.


7/08

Replacement/Upgrade/Accessory Kits

Replacement Kits

This section provides you with a complete list of all the spare parts that may be needed for the HercuLine

®

2000 Series Actuators and optional equipment.

To determine which kit you need, cross-reference Figure 37 through Figure 41 with Table 38 on page 96.

Each kit contains replacement parts accessories and instructions for component replacement.

11

Replacement/Upgrade/Accessory Kits

Replacement Kits

12

6,7

,8

14

11

14

Figure 37 Replacement Kits 6, 7, 8, 11, 12, 14


7/08

91


Replacement Kits

10

Figure 38 Replacement Kit 10


7/08

19

1

15

2


Replacement Kits

4,5,9

16

3

Figure 39 Replacement Kits 1, 2, 3, 4, 5, 9, 15, 16, 19


7/08

93


Replacement Kits

13

Figure 40 Replacement Kit 13


7/08


Replacement Kits

17, 18

Figure 41 Replacement Kits 17, 18


7/08

95


Replacement Kits

See Figure 37 through Figure 41 for drawings of replacement kit contents.

Table 38 Replacement kits

Qty/Unit Part Number

2

4

1

Qty/Unit

51450802-503

Relay Pwa

Plug 03 Position

Top Cover Gasket

Part Number

Description

Description

51451397-501

1

1

HercuLine ® CPU Bd Assembly

Plug, 10 Pos

1

1

4

1

Label Phonix Connector 1 To 10

Insulator

Pin, Snap Lock, .125 X .187 Lg

Top Cover Gasket

Qty/Unit Part Number Description

1


1

1

51451424-501

HercuLine ® Backplane Assy

Card Guide Assy

1

1

4

4

4

Machine Screw-Pan Head-Slotted

Screw,Trilob Philph #4-20x.38

Top Cover Gasket


1

2

2

1

2

51451656-505 1000 Ohm Potentiometer Kit 90 Degrees

(HercuLine

®

2000)

Pot 1 K Double 90 Degree

#6-32 Hex Nut N

2

#6 Lock Washer

Machine Screw-Pan Hd-Cross Rec

Top Cover Gasket

Kit Instruction# 62-86-33-38

Figure ID #

1

Figure ID #

2

Figure ID #

2

Figure ID #

3

Figure ID #

4


7/08


Replacement Kits


51451656-506 1000 Ohm Potentiometer Kit 150 Degrees

(HercuLine

®

2000)

1

2

2

1

2

2

Pot 1 K Double 150 Degree

#6-32 Hex Nut N

#6 Lock Washer


Top Cover Gasket



50018180-501

Description

Upgrade to Non Contact Position Sensor

(HercuLine

®

2001)

1

1

1

4

1

1

1

1


4

1

1

51452342-501

1

2

2

1

2

2


515000657-502

Screws SEMS #4-40 x .310 lg

Gasket

RVI T-Z Setup Gage

Stainless Steel Pin

Set Screw 3/32 x 4-40


#6 Lock Washer


Top Cover Gasket


Description

Rvit-Z Ncs Replacement Kit

Ncs, Rvit-Z Pwa 0-150

Machnl 4-40 X .31 Pnslstl

Top Cover Gasket

Description

10K Ohm Potentiometer Kit (HercuLine

®

Position Sensor SA2001

#6-32 Hex Nut N

2001)

Figure ID #

5

Figure ID #

6

Figure ID #

9

Figure ID #

19


7/08

97


Replacement Kits

Qty/Unit

Qty/Unit

Qty/Unit

4

1

4

4

2

Part Number

Part Number

Part Number

50011455-503

1

1

1

1

Split Washer M5

Description

51452174-501

1

1

1

1

Crank Arm

Screw,Hex Hd,1 3/4 X 1/4-20

Kllwss1/4sp

Nut Nmsndc 1/4-20


4

4

4

1

1

1

1

50011455-501

Motor 120v,50/60 Hz,

Capacitor, 3 µfd 400Vac

Cable plus Resistor assembly, 600 Ohm

1

Split Washer M5

M3 X 5mm lg screw w/ext tooth lock washer

Socket head cap screw-M5 x 12

Top Cover Gasket


Description

4

4

4

1

1

1

1

50011455-502


Capacitor, 4.0 µfd 400Vac


1

Split Washer M5



Top Cover Gasket


Description

240VAC/50/60HZ Motor Kit


Capacitor, .75 Mfd 400Vac



Butt Splice (SA2000)


Top Cover Gasket


Figure ID #

7

Figure ID #

7

Figure ID #

6

Figure ID #

7


7/08


Replacement Kits

1

1


1

1

51452443-501

51452443-507

51452443-508

51452443-509

51452443-510

51452443-511

1

1

1

1

1

1

1

1



51452443-503

1

1

1

1

1

1

Description

Spur Gear Kit

Figure ID #

10

Spur Gear 24p, 18t

Spur Gear 24p, 18t

Spur Gear 24p, 36t

Spur Gear 24p, 72t

Spur Gear 24p, 36t

Intermediate Shaft all except 7.5 seconds

Intermediate Shaft – 7.5 seconds

Kit Instructions# 62-86-33-35

Description

O-Ring 2.144 Id X 0.070 Buna N

Top Cover Gasket

O-Ring Buna N

Gasket Set Kit

Figure ID #

11

Cam Assembly (4 Aux switches, 2 end of travel switches)

Switch and Mounting Plate assembly (6


Description

Figure ID #

12


7/08

99


Replacement Kits


51452443-504

1

1

1

1

1

1

9

4

1

1

1

1

4

6


51452443-505

1

1

1

1

1

1

Display and Keypad Kit

Overlay, Display

Keypad, 6 Position

Description

Gasket,Adhesive Die Cut

Display Mtg Collar Machining

Support Plate-Keypad

Sems #4-40 X .310lg Pnphstl

Screw,Metric Panhd,Cross Rec

Sleeve, Keypad

Display/Keybd Cable

Top Cover Gasket

Description

R/C Kit (Motor date codes prior to 8/5/2005)

Capacitor, 2.25 Mfd

Resistor, 200 Ohm,25w

Capacitor, .75 Mfd, 400vac

Resistor, 500 Ohm,25w

Top Cover Gasket

Kit Instruction 62-86-33-44

Figure ID #

13

Figure ID #

14


7/08


Replacement Kits

Qty/Unit

51452443-506

1

1

1

1

1

1

1

1


Part Number

51500166-503

1

1

2

1


Description

R/C Kit (Motor date codes after to 8/5/2005)

Capacitor, 4.0 Mfd

Cable plus Resistor, 400Ohm

Capacitor, 3 Mfd, 400vac

Cable plus Resistor, 600 Ohm

Capacitor, 0.75 Mfd, 400vac

Cable plus Resistor, 1100 Ohm

Top Cover Gasket

Kit Instruction 62-86-33-44

Description

Power Distribution Pwa Kit

Power Dist Pwa

Insulator

Pin, Snap Lock, .125 X .187 Lg

Top Cover Gasket

Description

51500457-502

1 Transformer

1

2

2 Machine Screw-Pan Hd-Cross Rec

Top Cover Gasket


1

1

51500581-503

1

1

1

1

Auto/Manual Switch (upgrade for SA2000)

Nut, Sealing 3/8-32 Thrd

Knob

A/M Switch/Wire Assy

Label, Customer Wiring,

Top Cover Gasket

Figure ID #

Figure ID #

16

Figure ID #

17

1

1

1

1

1

1

Figure ID #

15


7/08

101


Upgrade Kits


51500581-504

1

1

1

1

1

1

Description

Auto/Manual Switch (upgrade for SA2001 & SA2002)

Nut, Sealing 3/8-32 Thrd

Knob

A/M Switch/Wire Assy

Label, Customer Wiring,

Top Cover Gasket

Figure ID #

18

Upgrade Kits


51452444-502

1

1

1

1

1

9

4

1

1

1

1

1

1

4

6

Description

Cover (with Display no Handwheel)

Gasket,adhesive die cut

Display mtg collar machining

Keypad, 6 position

Support plate-keypad

Top cover w/display no hndwhl

Sems #4-40 x .310lg pnphstl

Screw,metric panhd,cross rec

Sleeve, keypad

Display/keybd cable HercuLine 2001/2002

Top cover gasket


7/08


Upgrade Kits


51452444-503

1

1

1

1

1

1

1

9

1

1

4

1

1

4

6

1

1

1

1

Description

Cover with Display and Handwheel

Overlay, display

Gasket,adhesive die cut

Display mtg collar machining

Keypad, 6 position

Support plate-keypad

Top cover w/display & hndwheel

Sems #4-40 x .310lg pnphstl

Screw,metric panhd,cross rec

O-ring buna n

Sleeve, keypad

Display/keybd cable HercuLine ® 2001/2002

Shim

Top cover gasket

Qty/Unit

Qty/Unit

Part Number

51452444-504

Part Number

Description

Blank Cover with Handwheel

Description

51451656-510

2

1

1

1

2

Machine screw-pan hd-cross rec

Knob

Pot 1K double 90 degree


#6-32 hex nut N

2

2

1

1

2

2

2

3/32x4-40 setscrew sshxsocupsb

Flat washer M4 (zinc)

Resistor 158 ohms 1% 1/2W



7/08

103


Accessory Kits


2

51451656-511


Knob 1

1

1 Pot 1K double 150 degree

2

2

2

1

2

2

1

2


#6-32 hex nut N

3/32x4-40 setscrew sshxsocupsb

Flat washer M4 (zinc)

Resistor 158 ohms 1% 1/2W


Accessory Kits

Part Number Description

51197910-001 HAL Linkage Analysis software

51452354-509 HercuLink

®

software (PC/Palm)

51452354-510

51452174-501

51452791-001

51452352-501

Battery powered Palm/485 converter w/cables

Crank Arm - Standard

Crank Arm – 2003 Unit

Turk Cable for Communication Connection


7/08

Troubleshooting

Introduction

Troubleshooting

Introduction

Troubleshooting procedures can be followed when inaccurate or faulty actuator operation is detected. In this section, troubleshooting procedures consist of a few simple flow charts to test for proper function of various actuator components. Component replacement is at the PWA or assembly level.

Table 39 indicates some of the observable symptoms of failure that can be identified by noting the faulty actuator operation.

Table 39 Observable Symptoms of Failure

Symptom

No Actuator current output.

No Actuator slidewire output.

Local display does not light.

Actuator fails one or more power up diagnostics.

Actuator motor does not drive in response to input signal.

Actuator motor does not drive to proper position.

Actuator Motor is “Hunting”

(Motor does not drive to a position and stop.)

Procedure

Replace CPU Assembly

Replace CPU Assembly

See Figure 42

See Figure 43

Perform input calibration.

See Figure 42

Perform motor calibration.

Process control loop is not tuned correctly.

Refer to the Instruction Manual for your controller on how to tune a loop.

Increase the Deadband in the Actuator and/or in the control loop.

See page 85. Position sensor position is not correct.

Auto/Manual Switch does not operate correctly.

Relay(s) does not operate.

See Figure 45

See Figure 46


7/08

105

Troubleshooting

Troubleshooting Procedures

Troubleshooting Procedures

Overview

Follow the procedure or flow chart to test for and determine actuator component operation. When using the flow charts for troubleshooting, you may be instructed to go to another flow chart in order to identify the faulty component. Instruction for replacing actuator components can be found either in Maintenance

(page 87) or in the kit with the replacement components.

Equipment needed

You will need the following equipment in order to troubleshoot the symptoms listed in the tables that follow:

DC Milliammeter – mA DC

Calibration source – Volt, mA, etc.

Digital Voltmeter

Safety precautions

Exercise appropriate safety precautions when troubleshooting the actuator operation.




7/08

Troubleshooting


Test for Actuator Operation

A

Cycle power to actuator.

Yes

Does display light up?

No

Observe self test.

Move handwheel on actuator 2 or

3 turns.

Yes

Do all diagnostics pass?

RAMTST PASS

SEETST PASS

CALTST PASS

CFGTST PASS

All LEDs and display segments light?

Yes

No

Replace display assembly

E

No

B

Figure 42 Test for Actuator Operation

Does motor reposition itself?

Yes

Replace display assembly

No

E


7/08

107

Troubleshooting


Power Up Self Test Diagnostics

B

Cycle power to actuator.

Yes

Does display light up?

No

Observe self test.

A

Yes

RAMTST PASS?

No

Yes

SEETST PASS?

No

Replace CPU

Assembly.

Yes

CALTST PASS?

CFGTST PASS?

No

No

Check actuator calibration, recalibrate if necessary.

Check actuator configuration

(setup), reconfigure if necessary.

Cycle power to actuator. If CALTST fails again, replace

CPU assembly.

Cycle power to actuator. If CFGTST fails again, replace

CPU assembly.

Yes

Do all LEDs and display segments light up?

Yes

No

Replace display assembly.

E

Figure 43 Power Up Diagnostics

Test Non-Contact Sensor PWA

See page 85.


7/08

Troubleshooting


Test Power Distribution PWA

D

Remove top cover of actuator.

Check Fuses F1 and F2 on the power distribution

PWA.

Yes

Are fuses good?

No

Replace fuses with same type and rating

Yes

Is correct voltage present at test points?

See below.

No

Replace CPU assembly.

Replace Power

Distribution PWA.

Figure 44 Test Power Distribution PWA

Power Distribution PWA Test Points

Connector Test Points - Pins

J2 Pin 1 to pin 7

J3

J1

Pins 1,2 to pins 3, 4, 8

Pins 3, 4 to pin 7

Pins 5, 6 to pins 7, 8

Pins 1, 2 to pins 7, 8

Voltage

5 V

5 V

9 V

24 V

28 V + or – 3V


7/08

109

Troubleshooting


Test AUTO - MANUAL DRIVE Switch

E

Turn switch to

Manual CCW setting.

Yes

Does motor drive in the CCW direction?

No

Turn switch to

Manual CW setting.

OK

Yes

Does motor drive in the CW direction?

No

CCW

MANUAL

OFF

CW

OFF

A

U

T

O

Possible trouble spots a. Auto/Manual switch b. Power Supply PWA. (See D) c. Limit switches d. Motor e. R/C networks f. etc.,Others?

AUTO - MANUAL DRIVE

Figure 45 Test AUTO - MANUAL Switch


7/08

Troubleshooting


Test Relay Function

Press SET UP button on keypad to enter Set up mode.

Set suspect Relay type to MAN.

Place ohmmeter across associated relay contacts at

Actuator terminal block. See below.

RELAY1

RELAY2

RELAY3

RELAY4

Set AUTO -

MANUAL switch to MAN.

Yes

Does Relay operate?

No

OK

Replace Relay PWA or

Wire harness from Relay

PWA to terminal block.

See Relay replacement in Maintenance, Section 7.

Figure 46 Test Relay Function

NC

COM

NO

NC

COM

NO

NC

COM

NO

NC

COM

NO


7/08

111

Appendix A - HercuLine® 2001/2002 Configuration Record Sheet

Appendix A - HercuLine

®

2001/2002 Configuration Record

Sheet

Enter the value or selection for each set up parameter on this sheet so you will have a record of how your actuator is configured.

Parameter Setting Default Set Up Group

Prompt

SET INPUT IN TYP - Input Actuation Type

INP HI – Input High Range Value

INP LO – Input Low Range Value

FILTYP – Input Filter Type

LPFILT – Low Pass Filter Time Constant *

Direct – Actuator Rotation

Dband – Input Deadband

FSTYPH – Failsafehi Type

FSVALH – Failsafehi Input Value

FSTYPL – Failsafelo Type

FSVALL – Failsafelo Input Value

CHAR – Input Characterization type

CUSTOM -- Custom characterization type

X0 VAL -- User configurable characterizer value










X10 VAL - User configurable characterizer value









__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

55.0

60.0

65.0

70.0

75.0

80.0

85.0

90.0

10.0

15.0

20.0

25.0

30.0

35.0

40.0

45.0

50.0

See Note 1

100

0.0

LPAS

0

CCW

0.5

UP

100

DOWN

0

LINR

EQUL

0.0

5.0


7/08


Set Up Group

Prompt

SET RELAY

Parameter



Y0 VAL -- User configurable characterizer value










Y10 VAL - User configurable characterizer value











RTYP11 – Relay Type

R11VAL – Relay Value

R11 HL – Relay High/Low

R11SCALE– Relay Scale





RLY1HY – Relay Hysteresis







R22HL– Relay High/Low



Setting

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

Default

10.7

13.2

15.7

18.7

22.6

27.2

33.4

40

95.0

100.0

0

0.8

2.1

3.2

4.9

6.5

8.4

46

53.8

63.2

73.7

86.2

100

0

LO

X1

NONE

0

LO

X1

0

NONE

0

LO

X1

NONE

0

LO

X1

0

NONE


7/08

113


Set Up Group

Prompt

Parameter

SET CUROUT

SET COMM

SET DIGINP

SET DISPLA

SET LOCK

READ STATUS



















CUROUT - Output Signal Range

COMM – Communications Parameters

ADDRES – Device Address

BAUD – Baud Rate

XmtDLY – Response Delay

DBLBYT – Floating Point Data Format

DIGINP – Digital Input State

Endpos – End Position Value

DECMAL – Decimal Point Location

EUNITS – Units Display

UNITS – Display Units

LOCKID – Password Lock

MAENAB – Enabled

LOCK – Lock Out

FAILSF – Failsafe

RAMTST – RAM Test Diagnostic

SEETST – Serial EEPROM Test Diagnostic

CFGTST – Configuration Test Diagnostic

CALTST – Calibration Test Diagnostic

Setting Default

MODBUS

1

19.2K

20MS

FP B

UP

0

8888

Pcnt

ENG

0

ENAB

NONE

Read Only

Read Only

Read Only

Read Only

Read Only

NONE

0

LO

X1

NONE

0

LO

X1

0

NONE

0

LO

X1

NONE

0

LO

X1

0

See Note 1

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________


7/08


Set Up Group Parameter Setting

Prompt

SET DRVINF

SET MAIN

VERSON – Firmware Version

SPEED – Stroke Speed

POWER – Power Input Voltage Line Frequency

TAG – Tag Name

MFGDAT – Manufacturing Date

LREP – Date of Last Repair

LCAL – Date of Last Field Calibration

REPTYP – Repair Type

TEMP – Actuator Temperature

TEMPHI – High Temperature Limit

TEMPLO – Low Temperature Limit

ACST – Accumulated Stall Time

STARTS – Accumulated Motor Starts

RLnCNTS – Relay Cycle Counts n = 1, 2, 3, or 4

REGNy – Accumulated Motor Starts for regions of motor travel. y = 0 through 9

DATSAV – Forced maintenance data save

MANRST – Maintenance Statistic Reset

LDCAL – Restore Factory Calibration Type

LDCFG – Restore Factory Default Configuration

RESTRT – System Restart

NCSOUT – Non-contact sensor circuit output

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

__________________

CAL NCSOUT

Note 1: Type is set from model number.

Default

Read Only

Factory Set

Factory Set

Factory Set

Factory Set

Factory Set

Factory Set

Read Only

Read Only

Read Only

Read Only

Read Only

Read Only

Read Only

Read Only

DIS

NONE

NONE

DIS

DIS


7/08

115

Index

Index

A

Actuator Rotation, 40, 64

Actuator Set Up, 33

Set up groups, 34

Set up procedure, 36

Actuator Statistics

Accumulated motor starts, 59

Motor starts, 59

Relay cycle counts, 59

Reset, 60

Temperature limits, 59

Total degrees of motor travel, 59

Applications

Basic flow control, 27

Proportional flow with multiple actuators, 27

Split range, 26, 30

Approvals, 6

Auto/Manual Switch

Testing, 110

Auto-Manual Switch, 64

Auxiliary Switches, 81

Setting, 81

Auxiliary Switches/Relays, 6

B

Baud Rate, 9, 50

Burner Control/Flame Safety, 23

C

Calibration, 65

Set up, 66

Calibration Values

Restore, 61

CE Wiring, 21

Change Password

LOCKID parameter, 54

Clamp Bolt, 6

Communications, 7, 9

Floating point data transfer, 50

Configuration Prompt Hierarchy, 38

Configuration Record Sheet, 112

Configuration Tips, 33

Connections

Output, 23

Slidewire emulation, 23

Crank Arm, 5

Crank Arms, 16

Customer Connections, 17

CW and CCW Direction. See Actuator Rotation

D

Deadband, 7, 40

Decimal Point Location, 52

Deviation, 45

Relay type, 47

Device Address, 50

Direction of Rotation, 7

Duty Cycle, 7

E

Electrical and Performance Specifications, 6

Electrical Installation, 17

Enclosure, 5

Enclosure Rating, 6

End of travel Limit Switches, 6

Exiting Set Up mode, 33

F

Failsafe, 40, 41

Failsafe Input Value, 40, 41

Failsafe operation, 7

Feedback, 6

Flame Safety Module wiring diagram, 23

Fuses

Replacement, 89

G

Gear Train, 5

H

Handwheel, 5

HercuLine 2000 Terminal Connections, 18

HercuLine 2001/2002 with Auto/Manual Terminal

Connections, 19

HerculLine 2003 Wiring Connections and Operation, 20

Hysteresis, 7, 44

I

Input Calibration, 68

Input Characterization, 41

Input Filters, 7, 40

Input High Range, 39

Input Impedance, 6

Input Low Range, 39

Input Set Up Group, 39

Input Signal Connections, 22

Input Signals, 6


7/08

Index

Inputs, 39

Installation, 12

Installation Considerations, 13

Isolation, 6

K

Keypad, 8, 31

Description, 32

L

LEDs on Local Display, 32

Limit Switches, 78

Setting, 78

Linkage Kits, 96

Linkage Set-up, 15

Constant torque, 15

Crank arms, 16

Variable torque, 15

Load Requirement, 6

Local Auto/Manual Switch, 6

Local Display, 8, 31

Description, 31

LEDs description, 32

Operating displays, 84

Set up, 52

LOCK parameter, 33, 36

Lubrication, 5

Main (Worm) gear, 87

Spur gear, 87

M

Main Gear Lubrication, 87

Mains Supply, 6

Mechanical Installation, 15

Mechanical Stops, 5

Modbus communications, 50, 85

Model distinctions, 1

Motor, 6

Motor Calibration, 70

Motor Current, 6

Motor Speed, 56

Motor Stall, 84

Motor Starts, 45

Relay type, 48

Mounting, 13

N

Non-Contact Sensor, 87

Checking, 108

Operation, 85

Non-Contact Sensor Output Calibration, 72, 73

O

Operating Temperature, 7

Output Calibration, 71

Output Shaft, 5

Output Torque, 5

Output Type, 49

Outputs, 49

P

Password, 60

(LOCKID), 53

Change, 54

PDA, 9

Position Range

Relay type, 46

Position sensing, 7

POSITION SENSOR OUTPUT, 63

Power Supply PWA

Checking, 109

Product Description, 1

Programmable Functions, 8

Pushbuttons

Description, 32

R

Regions of Motor Travel, 62

REGN parameter, 59

Relative Humidity, 5

Relay Function

Testing, 111

Relay PWA Replacement, 90

Relay Type, 44, 45

Remote Setpoint Operation, 85

Repeatability, 7

Restore Factory Calibration Values, 61

Rotation, 5

S

Scale, 5

Scrolling through Set Up Groups, 33

Self-test Diagnostics, 55, 83, 108

Sensitivity, 7

Set Up and Calibration Procedures, 31

Set Up Groups

Communications, 50

Current out, 49

Digital input, 51

Display, 52

Drive, 56

Input, 39

Lock, 53

Maintenance, 59

Read status, 55

Relays, 44

Slidewire Emulation, 23

Solid State Motor Control, 7 specifications, 5

Split Range, 26

Spur Gear Lubrication, 87


7/08

117

Index

Stall, 84

Start Up Checklist, 83

Storage Temperature, 5

Stroke Speed, 56

T

Tag Name, 58

TAG parameter, 56

Technical and Operating Specifications, 5

Temperature Coefficient, 7

Terminal Connections, 18, 19

Total Degrees of Motor Travel

TOTDEG parameter, 59

Troubleshooting, 105

Equipment, 106

V

Voltage/ Supply Stability, 7

W

Weight, 5

Z

Zero Suppression, 7


7/08


7/08

119

Honeywell Process Solutions

Industrial Measurement and Control

512 Virginia Drive

Fort Washington, PA 19034

62-86-25-10 0708 Printed in USA

http://hpsweb.honeywell.com

No results