STMicroelectronics STM32F7 46NG Discovery kit User manual

UM1907
User manual
Discovery kit for STM32F7 Series with STM32F746NG MCU
Introduction
The STM32F746G-DISCO discovery board (32F746GDISCOVERY) is a complete
demonstration and development platform for STMicroelectronics ARM® Cortex®-M7 corebased STM32F746NGH6 microcontroller. This microcontroller features four I2Cs, six SPIs
with three multiplexed simplex I2S, SDMMC, four USARTs, four UARTs, two CANs, three
12-bit ADCs, two 12-bit DACs, two SAIs, 8- to 14-bit digital camera module interface,
internal 320+16+4 KB SRAM and 1 MB Flash memory, USB HS OTG, USB FS OTG,
Ethernet MAC, FMC interface, Quad-SPI interface, SWD debugging support. This discovery
board offers everything required for users to get started quickly and develop applications
easily.
The full range of hardware features on the board helps to evaluate almost all peripherals
(USB OTG HS, USB OTG FS, Ethernet 10/100Mb, MicroSD Card, USART, SAI Audio DAC
stereo with audio jack input and output, MEMS digital microphones, SDRAM, Quad-SPI
Flash memory, 4.3-inch color LCD-TFT with a capacitive multi-touch panel, SPDIF RCA
input, etc.) and develop your own applications. Arduino Uno V3 connectors make it possible
to easily connect extension shields or a daughterboard for your specific application. The
integrated ST-LINK/V2-1 provides an embedded in-circuit debugger and programmer for the
STM32 MCU.
The STM32F746G-DISCO board comes with the STM32 comprehensive software HAL
library together with various packaged software examples, as well as a direct access to
mbed online resources at http://mbed.org.
Figure 1. STM32F746G-DISCO board (top view)
Figure 2. STM32F746G-DISCO board (bottom view)
1. Pictures not contractual.
November 2015
DocID027942 Rev 2
1/49
www.st.com
1
Contents
UM1907
Contents
1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2
Demonstration software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3
Product marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5
Technology partners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
6
Hardware layout and configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6.1
7
2/49
Embedded ST-LINK/V2-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
6.1.1
Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6.1.2
ST-LINK/V2-1 firmware upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6.2
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6.3
Programing/debugging when the power supply is not from
ST-LINK (5V link) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6.4
Clock sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6.5
Reset sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6.6
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6.7
USB OTG FS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.8
USB OTG HS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.9
MicroSD card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.10
Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6.11
SDRAM memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6.12
Quad-SPI Nor Flash memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6.13
Camera module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6.14
Display LCD-TFT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7.1
I2C extension connector CN2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7.2
Camera module connector P1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7.3
Arduino Uno revision 3 connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
DocID027942 Rev 2
UM1907
8
Contents
7.4
USB OTG HS micro-AB connector CN12 . . . . . . . . . . . . . . . . . . . . . . . . 22
7.5
Ethernet RJ45 connector CN9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.6
USB OTG FS micro-AB connector CN13 . . . . . . . . . . . . . . . . . . . . . . . . . 23
7.7
MicroSD connector CN3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7.8
ST-LINK/V2-1 USB type B connector CN14 . . . . . . . . . . . . . . . . . . . . . . . 24
7.9
Audio stereo speakers JP3 and JP4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
7.10
Audio green jack (line Out) CN10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
7.11
Audio blue jack (line In) CN11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
7.12
SPDIF input RCA connector CN1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Electrical schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Appendix A STM32F746G-DISCO IO Assignment . . . . . . . . . . . . . . . . . . . . . . . . 39
Appendix B Mechanical drawing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Appendix C Federal Communications Commission (FCC) and
Industry Canada (IC) Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . 47
C.1
C.2
FCC Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
C.1.1
Part 15.19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
C.1.2
Part 15.105 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
C.1.3
Part 15.21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
IC Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
C.2.1
Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
C.2.2
Déclaration de conformité. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
DocID027942 Rev 2
3/49
3
List of tables
UM1907
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
4/49
I2C extension connector CN2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Camera module connector P1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Arduino connectors (CN4, CN5, CN6, CN7). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
USB OTG HS micro-AB CN12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
RJ45 connector CN9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
USB OTG FS micro-AB connector CN13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
MicroSD connector CN3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
USB type B connector CN14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
SPDIF input RCA connector CN1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
STM32F746G-DISCO IO assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
DocID027942 Rev 2
UM1907
List of figures
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Figure 17.
Figure 18.
Figure 19.
Figure 20.
Figure 21.
Figure 22.
Figure 23.
Figure 24.
Figure 25.
Figure 26.
Figure 27.
Figure 28.
Figure 29.
Figure 30.
Figure 31.
Figure 32.
STM32F746G-DISCO board (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
STM32F746G-DISCO board (bottom view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Hardware block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
STM32F746G-DISCO discovery board top layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
STM32F746G-DISCO discovery board bottom layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
JP1 (5V ext) from JP2 (5V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
JP1 (5V ext) from CN6 (Vin) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
JP1 (5V link) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
JP1 (usb_fs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
JP1 (usb_hs). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Inside RJ45 jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
I2C extension connector CN2 (front view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Camera module connector P1 (front view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
USB OTG micro-AB connector CN12 (front view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Ethernet RJ45 connector CN9 (front view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
USB OTG micro-AB connector CN13 (front view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
MicroSD connector CN3 (front view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
USB type B connector CN14 (front view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
STM32F746 discovery interconnection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
ST-LINK/V2-1 with support of SWD only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Joystick, LEDs and pushbutton . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Audio codec Cirrus and connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Quad-SPI Flash memory (MICRON) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Arduino Uno connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
SDRAM (MICRON) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
USB OTG FS with micro A-B connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
STM32F746NGH6 connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
USB OTG HS PHY with micro A-B connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Ethernet PHY with RJ45 connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
External camera connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4.3-inch LCD with capacitive touch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Mechanical drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
DocID027942 Rev 2
5/49
5
Features
1
2
UM1907
Features
•
STM32F746NGH6 microcontroller featuring 1 Mbytes of Flash memory and
340 Kbytes of RAM, in BGA216 package
•
On-board ST-LINK/V2-1 supporting USB reenumeration capability
•
Mbed-enabled (mbed.org)
•
USB functions: virtual COM port, mass storage, debug port
•
4.3-inch 480x272 color LCD-TFT with capacitive touch screen
•
Camera connector
•
SAI audio codec
•
Audio line in and line out jack
•
Stereo speaker outputs
•
Two ST MEMS microphones
•
SPDIF RCA input connector
•
Two pushbuttons (user and reset)
•
128-Mbit Quad-SPI Flash memory
•
128-Mbit SDRAM (64 Mbits accessible)
•
Connector for microSD card
•
RF-EEPROM daughterboard connector
•
USB OTG HS with Micro-AB connectors
•
USB OTG FS with Micro-AB connectors
•
Ethernet connector compliant with IEEE-802.3-2002
•
Five power supply options:
–
ST LINK/V2-1
–
USB FS connector
–
USB HS connector
–
VIN from Arduino connector
–
External 5 V from connector
•
Power supply output for external applications: 3.3 V or 5 V
•
Arduino Uno V3 connectors
•
Comprehensive free software including a variety of examples, part of STM32Cube
package
•
Supported by a wide choice of integrated development environments
Demonstration software
The demonstration software is preloaded in the STM32F746NGH6 Flash memory. The
latest versions of the demonstration source code and associated documentation can be
downloaded from www.st.com/stm32f7-discovery.
6/49
DocID027942 Rev 2
UM1907
3
Product marking
Product marking
Evaluation tools marked as "ES" or "E" are not yet qualified and therefore they are not ready
to be used as reference design or in production. Any consequences deriving from such
usage will not be at ST charge. In no event, ST will be liable for any customer usage of
these engineering sample tools as reference design or in production.
"E" or "ES" marking examples of location:
4
•
On the targeted STM32 that is soldered on the board (for illustration of STM32 marking,
refer to the section “Package characteristics” of the STM32 datasheet at www.st.com).
•
Next to the evaluation tool ordering part number, that is stuck or silk-screen printed on
the board.
Ordering information
To order the discovery kit with STM32F746NG MCU, use the order code:
STM32F746G-DISCO.
5
Technology partners
MICRON:
•
128-Mbit SDRAM (64 Mbits accessible on the kit), part number MT48LC4M32B2
•
128-Mbit Quad-SPI NOR Flash memory device, part number N25Q128A
ROCKTECH:
•
Color display, 4.3-inch LCD-TFT (resolution: 480x272), capacitive touch,
part number RK043FN48H-CT672B
DocID027942 Rev 2
7/49
48
Hardware layout and configuration
6
UM1907
Hardware layout and configuration
STM32F746G-DISCO discovery board is designed around the STM32F746NGH6 (216-pin
TFBGA package). The hardware block diagram (see Figure 3) illustrates the connection
between STM32F746NGH6 and peripherals (SDRAM, Quad-SPI Flash memory, camera
module, color LCD, USB OTG connectors, USART, Ethernet, Audio, SPDIFRX, MicroSD
card, Arduino Uno shields and embedded ST-LINK) and Figure 3 will help to locate these
features on the actual discovery board.
Figure 3. Hardware block diagram
93RZHU
6XSSO\
.+]&U\VWDO
LQFK:49*$
/&'
$5'8,128QR
6KLHOGVFRQQHFWRUV
57&
27*
)6
0LFUR86%
FRQQHFWRU
27*
+6
+63+<
0LFUR86%
FRQQHFWRU
*3,2
3XVKEXWWRQ
:DNHXS
/&'
*3,2V
63',)5;
63',)GHFRGHU
5&$,1SXW
FRQQHFWRU
4XDG63,
4XDG63,)ODVK
PHPRU\
9&3
8$57
670)1*+
67/,1.9
6:'
6'5$0
)0&
0LFUR6'FDUG
&RQQHFWRU
(WKHUQHW3+<
5-FRQQHFWRU
,&
,&H[WHQVLRQ
FRQQHFWRU
6$,
$XGLR'$&
$PSOLILHU
6WHUHR-DFN
/LQH,QSXW
6WHUHR-DFN
/LQH2XWSXW
6'00&
50,,
&DSDFLWLYH
7RXFK6FUHHQ
0XOWLSRLQWV
'&0,
&DPHUDFRQQHFWRU
06Y9
8/49
DocID027942 Rev 2
UM1907
Hardware layout and configuration
Figure 4. STM32F746G-DISCO discovery board top layout
$XGLRFRGHF
0ELW6'5$00[
-DFNVVWHUHRPP
,1DQG287
,&H[WHQVLRQFRQQHFWRU
670)1*+
7)%*$
63',)LQSXW
5&$FRQQHFWRU
5-VLQJOHSRUW
+L6SHHG86%
3+<8/3,
'&0,FDPHUD
FRQQHFWRU
+HDGHUV$UGXLQR
0LFUR86%
0ELW4XDG63,
4XDG'XDO
0LFUR6'FDUGFRQQHFWRU
0LQL86%W\SH%
67/,1.9
+HDGHUV$UGXLQR
3RZHU
VXSSO\LQOHW9
3RZHUVXSSO\VHOHFWRU
3XVKEXWWRQVXVHUDQG567
069
DocID027942 Rev 2
9/49
48
Hardware layout and configuration
UM1907
Figure 5. STM32F746G-DISCO discovery board bottom layout
7ZR670(06PLFURSKRQHV
LQFK[FRORU/&'7)7
ZLWKFDSDFLWLYHWRXFKVFUHHQ
069
10/49
DocID027942 Rev 2
UM1907
6.1
Hardware layout and configuration
Embedded ST-LINK/V2-1
The ST-LINK/V2-1 programming and debugging tool is integrated on the
STM32F746G-DISCO discovery board. Compared to ST-LINK/V2 the changes are listed
below.
The new features supported on ST-LINK/V2-1 are:
•
USB software re-enumeration
•
Virtual Com port interface on USB
•
Mass storage interface on USB
•
USB power management request for more than 100mA power on USB
These features are no more supported on ST-LINK/V2-1:
•
SWIM interface
•
Application voltage lower than 3 V
For all general information concerning debugging and programming features common
between V2 and V2-1 please refer to ST-LINK/V2 user manual (UM1075).
6.1.1
Drivers
The ST-LINK/V2-1 requires a dedicated USB driver, which, for Windows XP, 7 and 8, can be
found at www.st.com.
In case the STM32F746G-DISCO discovery board is connected to the PC before the driver
is installed, some STM32F746G-DISCO interfaces may be declared as “unknown” in the PC
device manager. In this case the user must install the driver files, and update the driver of
the connected device from the device manager.
Note:
Prefer using the “USB Composite Device” handle for a full recovery.
DocID027942 Rev 2
11/49
48
Hardware layout and configuration
6.1.2
UM1907
ST-LINK/V2-1 firmware upgrade
The ST-LINK/V2-1 embeds a firmware upgrade mechanism for in-situ upgrade through the
USB port. As the firmware may evolve during the life time of the ST-LINK/V2-1 product (for
example new functionality, bug fixes, support for new microcontroller families), it is
recommended to visit www.st.com before starting to use the STM32F746G-DISCO board
and periodically, in order to stay up-to-date with the latest firmware version.
6.2
Power supply
STM32F746G-DISCO discovery board is designed to be powered by 5V DC power supply.
It’s possible to configure the discovery board to use any of the following five sources for the
power supply.
•
5V DC power adapter connected to JP2 (external power supply on silkscreen of JP1
(5V ext)). In this case, the STM32F746G-DISCO discovery board must be powered by
a power supply unit or by an auxiliary equipment complying with standard
EN-60950-1: 2006+A11/2009, and must be Safety Extra Low Voltage (SELV) with
limited power capability.
Figure 6. JP1 (5V ext) from JP2 (5V)
•
7-12V DC power from CN6 pin named Vin on silkscreen, the extension connectors for
Arduino UNO shields or daughterboard (external power source on silkscreen of JP1
(5V ext)).
Figure 7. JP1 (5V ext) from CN6 (Vin)
12/49
DocID027942 Rev 2
UM1907
Hardware layout and configuration
•
5V DC power with limitation from CN14, the USB type mini-B connector of ST-LINK/V21 (USB 5V power source on silkscreen of JP1 (5V link)). It is the default setting. If the
USB enumeration succeeds (as explained below), the ST-LINK 5V link power is
enabled, by asserting the PWR_ENn signal. This pin is connected to a power switch
(ST890), which powers the board. This power switch features also a current limitation
to protect the PC in case of a short-circuit on board (more than 600mA).
STM32F746G-DISCO discovery board can be powered from ST-LINK USB connector CN14
(5V link), but only ST-LINK circuit has the power before USB enumeration, because the host
PC only provides 100mA to the board at that time. During the USB enumeration,
STM32F746G-DISCO board asks for the 500mA power to the host PC. If the host is able to
provide the required power, the enumeration finishes by a “SetConfiguration” command and
then, the power transistor U8 (ST890) is switched ON, the red LED LD2 is turned ON, thus
STM32F746G-DISCO board can consume maximum 500mA current, but no more. If the
host is not able to provide the requested current, the enumeration fails. Therefore the ST890
(U8) remains OFF and the MCU part including the extension board won’t be powered. As a
consequence the red LED LD2 remains turned OFF. In this case it is mandatory to use an
external power supply.
Figure 8. JP1 (5V link)
Note:
In case the board is powered by an USB charger, there is no USB enumeration, so the led
LD2 remains set to OFF permanently and the board is not powered. Only in this specific
case, the resistor R109 needs to be soldered, to allow the board to be powered anyway.
The LED LD2 is lit when the STM32F746G-DISCO discovery board is powered by the 5V
correctly.
Caution:
Do not connect PC to ST-LINK (CN14) when R109 is soldered. PC may be damaged or the
board not powered correctly.
DocID027942 Rev 2
13/49
48
Hardware layout and configuration
•
UM1907
5V DC power with 500mA limitation from CN13, the USB OTG FS micro-AB connector
(USB 5V power source on silkscreen of JP1 (usb_fs)).
Figure 9. JP1 (usb_fs)
•
5V DC power with 500mA limitation from CN12, the USB OTG HS micro-AB connector
(USB 5V power source on silkscreen of JP1 (usb_hs)).
Figure 10. JP1 (usb_hs)
6.3
Programing/debugging when the power supply is not from
ST-LINK (5V link)
It is mandatory to power the board first using JP1 (5V ext) or (usb_hs) or (usb_fs), then
connecting the USB cable to the PC. Proceeding this way ensures that the enumeration
succeeds thanks to the external power source.
The following power sequence procedure must be respected:
1.
Connect the jumper JP1 on (5V ext) or (usb_hs) or (usb_fs)
2.
Connect the external power source to JP2 or CN6 or CN12 or CN13
3.
Check the red LED LD2 is turned ON
4.
Connect the PC to USB connector CN14
If this order is not respected, the board may be powered by VBUS first from ST-LINK, and
the following risks may be encountered:
14/49
DocID027942 Rev 2
UM1907
6.4
Hardware layout and configuration
1.
If more than 500mA current is needed by the board, the PC may be damaged or
current can be limited by PC. As a consequence the board is not powered correctly.
2.
500mA will be requested at the enumeration, so there is a risk that the request is
rejected and enumeration does not succeed if PC can’t provide such current.
Clock sources
Up to 3 clock sources as described below:
6.5
•
X1, 24MHz oscillator for USB OTG HS PHY and camera module (daughterboard)
•
X2, 25MHz oscillator for STM32F746NGH6 microcontroller and Ethernet PHY.
•
X3, 32KHz crystal for STM32F746NGH6 embedded RTC
Reset sources
The reset signal of STM32F746G-DISCO discovery board is active low and the reset
sources include:
6.6
•
Reset button B2
•
Arduino Uno shield board from CN6
•
Embedded ST-LINK/V2-1
Audio
An audio codec WM8994ECS/R from CIRRUS with 4 DACs & 2ADCs is connected to SAI
interface of STM32F746NGH6. It communicates with STM32F746NGH6 via I2C bus shared
with the camera module and I2C extension connector.
•
The analog line input is connected to ADC of WM8994ECS/R through blue audio jack
CN11.
•
The analog line output is connected to DAC of WM8994ECS/R via green audio jack
CN10.
•
Two external speakers can be connected to WM8994ECS/R via JP3 for right speaker
and JP4 for left speaker.
•
Two digital microphones (ST MEMs microphone) MP34DT01TR are on STM32F746GDISCO discovery board. They are connected to the input digital microphones of
WM8994ECS/R.
•
One coaxial connector CN1 is implemented on STM32F746G-DISCO to receive
external audio data compatible with SPDIF specification.
DocID027942 Rev 2
15/49
48
Hardware layout and configuration
6.7
UM1907
USB OTG FS
STM32F746G-DISCO discovery board supports USB OTG full speed communication via a
USB micro-AB connector (CN13) and USB power switch (U6) connected to VBUS. The
discovery board can be powered by this USB connection at 5V DC with 500mA current
limitation.
A green LED LD5 will be lit in one of these cases:
•
Power switch (U6) is ON and STM32F746G-DISCO works as an USB host
•
VBUS is powered by another USB host when STM32F746G-DISCO works as an USB
device.
The red LED LD6 will be lit when an over-current occurs.
Note:
STM32F746G-DISCO board should be powered by external power supply when using OTG
function.
6.8
USB OTG HS
STM32F746G-DISCO discovery board supports USB OTG high speed communication via
an USB micro-AB connector (CN12), USB high speed PHY (U15) USB3320C-EZK from
MICROCHIP for high speed function.
The discovery board can be powered by the USB connectors (CN12) at 5V DC with 500mA
current limitation.
An USB power switch (U7) is also connected on VBUS and provides power to CN12.
The green LED LD4 will be lit when either:
•
Power switch (U17) is ON and STM32F746G-DISCO works as an USB host
•
VBUS is powered by another USB host when STM32F746G-DISCO works as an USB
device.
The red LED LD3 will be lit when an over-current occurs.
Note:
STM32F746G-DISCO board should be powered by external power supply when using OTG
function.
6.9
MicroSD card
The 2GB (or more) MicroSD card connected to SDMMC1 port of STM32F746NGH6 is
supported by the board.
16/49
DocID027942 Rev 2
UM1907
6.10
Hardware layout and configuration
Ethernet
STM32F746G-DISCO discovery board supports 10M/100M Ethernet communication by a
PHY LAN8742A-CZ-TR (U9) from MICROCHIP and integrated RJ45 connector (CN9).
Ethernet PHY is connected to STM32F746NGH6 via RMII interface.
25 MHz clock for the PHY is generated by the oscillator X2, the 50 MHz clock for the
STM32F746NGH6 is generated by the PHY RMII_REF_CLK.
Figure 11. Inside RJ45 jack
6.11
SDRAM memory
128-Mbit SDRAM (MT48LC4M32B2B5-6A from MICRON) is connected to FMC interface of
STM32F746NGH6. Only lower 16bits data are used (64-Mbits accessible). DQ16 to DQ31
are unused and connected to a 10K ohm pull-down resistor.
6.12
Quad-SPI Nor Flash memory
128-Mbit Quad-SPI Nor Flash memory (N25Q128A13EF840E from MICRON) is connected
to Quad-SPI interface of STM32F746NGH6.
DocID027942 Rev 2
17/49
48
Hardware layout and configuration
6.13
UM1907
Camera module
A connector P1 with the DCMI signals is available to connect a camera module such as
STM32F4DIS-CAM (ST order code).
6.14
Display LCD-TFT
The color display from ROCKTECH, 4.3-inch 480x272 LCD-TFT with capacitive touch panel
is connected to RGB LCD interface of STM32F746NGH6.
18/49
DocID027942 Rev 2
UM1907
Connectors
7
Connectors
7.1
I2C extension connector CN2
Figure 12. I2C extension connector CN2 (front view)
069
Table 1. I2C extension connector CN2
7.2
Pin number
Description
Pin number
Description
1
I2C_SDA (PB9)
5
+3V3
2
NC
6
NC
3
I2C_SCL (PB8)
7
GND
4
RESET(PC10)
8
NC or 5V
Camera module connector P1
Figure 13. Camera module connector P1 (front view)
Table 2. Camera module connector P1
Pin number
Description
Pin number
Description
1
GND
16
GND
2
NC
17
DCMI_HSYNC
3
NC
18
NC
4
DCMI_D0
19
DCMI_VSYNC
5
DCMI_D1
20
3V3
DocID027942 Rev 2
19/49
48
Connectors
UM1907
Table 2. Camera module connector P1 (continued)
7.3
Pin number
Description
Pin number
Description
6
DCMI_D2
21
Camera_CLK (OSC_24M)
7
DCMI_D3
22
NC
8
DCMI_D4
23
GND
9
DCMI_D5
24
NC
10
DCMI_D6
25
DCMI_PWR_EN
11
DCMI_D7
26
DCMI_NRST
12
NC
27
DCMI_SDA
13
NC
28
DCMI_SCL
14
GND
29
GND
15
DCMI_PIXCK
30
3V3
Arduino Uno revision 3 connectors
CN4, CN5, CN6 and CN7 are female connectors compatible with Arduino standard. Most
shields designed for Arduino can fit to the STM32F746G-DISCO discovery board.
The Arduino connectors on STM32F746G-DISCO discovery board support the Arduino Uno
revision 3.
Caution:
20/49
The IOs of STM32 microcontroller are 3.3 V compatible instead of 5 V for Arduino Uno.
DocID027942 Rev 2
UM1907
Connectors
Table 3. Arduino connectors (CN4, CN5, CN6, CN7)
Left connectors
CN No.
Pin
No.
Pin
Name
MCU
Pin
Right connectors
Function
-
CN6
power
MCU
Pin
Pin
Name
Pin
No.
I2C1_SCL
PB8
D15
10
I2C1_SDA
PB9
D14
9
AVDD
-
AREF
8
Ground
-
GND
7
1
NC
-
-
SPI2_SCK
PI1
D13
6
2
IOREF
-
3.3V Ref
SPI2_MISO
PB14
D12
5
3
RESET
NRST
RESET
TIM12_CH2,
SPI2_MOSI
PB15
D11
4
4
+3V3
-
3.3V
input/output
TIM5_CH4,
SPI2_NSS
PI0
D10
3
5
+5V
-
5V output
TIM2_CH1
PA15
D9
2
6
GND
-
Ground
-
PI2
D8
1
7
GND
-
Ground
8
VIN
-
Power input
-
CN5
analog
Function
-
PI3
D7
8
TIM12_CH1
PH6
D6
7
A0
PA0
ADC3_IN0
TIM1_CH1
PA8
D5
6
2
A1
PF10
ADC3_IN8
-
PG7
D4
5
3
A2
PF9
ADC3_IN7
TIM3_CH1
PB4
D3
4
4
A3
PF8
ADC3_IN6
-
PG6
D2
3
A4
PF7 or
PB(1)
ADC3_IN5
(PF7) or
I2C1_SDA
(PB9)
USART6_TX
PC6
D1
2
A5
PF6 or
PB8(1)
ADC3_IN4
(PC0) or
I2C1_SCL
(PB8)
USART6_RX
PC7
D0
1
6
CN7
digital
-
-
1
5
CN No.
CN4
digital
1. Please refer to Table 10 for details.
DocID027942 Rev 2
21/49
48
Connectors
7.4
UM1907
USB OTG HS micro-AB connector CN12
Figure 14. USB OTG micro-AB connector CN12 (front view)
Table 4. USB OTG HS micro-AB CN12
7.5
Pin number
Description
Pin number
Description
1
VBUS
4
ID
2
D-
5
GND
3
D+
-
-
Ethernet RJ45 connector CN9
Figure 15. Ethernet RJ45 connector CN9 (front view)
22/49
DocID027942 Rev 2
UM1907
Connectors
Table 5. RJ45 connector CN9
7.6
Pin number
Description
Pin number
Description
1
A, yellow LED
7
RD+
2
K, yellow LED
8
RD-
3
TD+
9
NC
4
TD-
10
GND
5
CT, 3V3
11
K, green LED
6
CT, 3V3
12
A, green LED
USB OTG FS micro-AB connector CN13
Figure 16. USB OTG micro-AB connector CN13 (front view)
Table 6. USB OTG FS micro-AB connector CN13
Pin number
Description
Pin number
Description
1
VBUS (PA9)
4
ID (PA10)
2
D- (PA11)
5
GND
3
D+ (PA12)
-
-
DocID027942 Rev 2
23/49
48
Connectors
7.7
UM1907
MicroSD connector CN3
Figure 17. MicroSD connector CN3 (front view)
Table 7. MicroSD connector CN3
7.8
Pin number
Description
Pin number
Description
1
SDMMC_D2 (PC10)
6
Vss/GND
2
SDMMC_D3 (PC11)
7
SDMMC_D0 (PC8)
3
SDMMC_CMD (PD2)
8
SDMMC_D1 (PC9)
4
+3.3V
9
GND
5
SDMMC_CK (PC12)
10
MicroSDcard_detect (PC13)
ST-LINK/V2-1 USB type B connector CN14
The USB connector CN21 is used to connect embedded ST-LINK/V2-1 to PC for
programming and debugging of STM32F746NGH6 microncontroller.
Figure 18. USB type B connector CN14 (front view)
24/49
DocID027942 Rev 2
UM1907
Connectors
Table 8. USB type B connector CN14
7.9
Pin number
Description
Pin number
Description
1
VBUS (power)
4
GND
2
DM
5, 6
Shield
3
DP
-
-
Audio stereo speakers JP3 and JP4
The stereo audio outputs JP3 and JP4 are available to support stereo speakers (left and
right)
7.10
Audio green jack (line Out) CN10
A 3.5mm stereo audio green jack output CN10 is available to support the headphone.
7.11
Audio blue jack (line In) CN11
A 3.5mm stereo audio blue jack input CN11 is available to support the audio line input.
7.12
SPDIF input RCA connector CN1
Table 9. SPDIF input RCA connector CN1
Pin number
Description
Pin number
Description
1
SPDIF_RX0 (PD7)
2
GND
2
GND
-
-
DocID027942 Rev 2
25/49
48
26/49
DocID027942 Rev 2
OTG_HS_OverCurrent
ULPI_DIR
ULPI_STP
ULPI_NXT
ULPI_CK
ULPI_D[0..7]
OTG_FS_PowerSwitchOn
OTG_FS_OverCurrent
OTG_FS_N
OTG_FS_P
OTG_FS_ID
OTG_FS_VBUS
RMII_RXER
RMII_TXD0
RMII_TX_EN
RMII_RXD0
RMII_REF_CLK
RMII_CRS_DV
RMII_MDC
RMII_MDIO
RMII_TXD1
RMII_RXD1
DCMI_NRST
DCMI_D[0..7]
DCMI_PWR_EN
DCMI_VSYNC
DCMI_HSYNC
DCMI_PIXCK
DCMI_SDA
DCMI_SCL
OTG_HS_OverCurrent
ULPI_DIR
ULPI_STP
ULPI_NXT
ULPI_CK
ULPI_D[0..7]
AUDIO_SDA
AUDIO_SCL
SAI2_MCLKA
SAI2_SCKA
SAI2_FSA
SAI2_SDA
SAI2_SDB
Audio_INT
TP_PH15
SPDIF_RX0
QSPI_D3
QSPI_D2
QSPI_D1
QSPI_D0
QSPI_CLK
QSPI_NCS
OSC_25M
ARD_A[0..5]
ARD_D[0..15]
uSD_CLK
uSD_CMD
uSD_D0
uSD_D1
uSD_D2
uSD_D3
uSD_Detect
SWDIO
SWCLK
NRST
SWO
VCP_RX
VCP_TX
B_USER
EXT_SCL
EXT_SDA
EXT_RST
FMC_A[0..11]
FMC_D[0..15]
FMC_SDNWE
FMC_SDNRAS
FMC_SDNCAS
FMC_SDCLK
FMC_BA0
FMC_BA1
FMC_SDNE0
FMC_SDCKE0
FMC_NBL0
FMC_NBL1
OTG_FS_PowerSwitchOn
OTG_FS_OverCurrent
OTG_FS_N
OTG_FS_P
OTG_FS_ID
OTG_FS_VBUS
RMII_RXER
RMII_TXD0
RMII_TX_EN
RMII_RXD0
RMII_REF_CLK
RMII_CRS_DV
RMII_MDC
RMII_MDIO
RMII_TXD1
RMII_RXD1
DCMI_NRST
DCMI_D[0..7]
DCMI_PWR_EN
DCMI_VSYNC
DCMI_HSYNC
DCMI_PIXCK
DCMI_SDA
DCMI_SCL
LCD_R[0..7]
LCD_G[0..7]
LCD_B[0..7]
LCD_BL_CTRL
LCD_HSYNC
LCD_CLK
LCD_VSYNC
LCD_DISP
LCD_DE
LCD_RST
LCD_INT
LCD_SDA
LCD_SCL
PA[0..15]
PB[0..15]
PC[0..15]
PD[0..15]
PE[0..15]
PF[0..15]
PG[0..15]
PH[0..15]
PI[0..15]
PJ[0..15]
PK[0..7]
U_STM32F7
STM32F7.SchDoc
uSD_CLK
uSD_CMD
uSD_D0
uSD_D1
uSD_D2
uSD_D3
uSD_Detect
SWDIO
SWCLK
NRST
SWO
VCP_RX
VCP_TX
B_USER
EXT_SCL
EXT_SDA
EXT_RST
FMC_A[0..11]
FMC_D[0..15]
FMC_SDNWE
FMC_SDNRAS
FMC_SDNCAS
FMC_SDCLK
FMC_BA0
FMC_BA1
FMC_SDNE0
FMC_SDCKE0
FMC_NBL0
FMC_NBL1
AUDIO_SDA
AUDIO_SCL
SAI2_MCLKA
SAI2_SCKA
SAI2_FSA
SAI2_SDA
SAI2_SDB
Audio_INT
TP_PH15
SPDIF_RX0
QSPI_D3
QSPI_D2
QSPI_D1
QSPI_D0
QSPI_CLK
QSPI_NCS
OSC_25M
ARD_A[0..5]
ARD_D[0..15]
Matched Net Lengths [Tolerance = 100mil] U_SDRAM
SDRAM.SchDoc
FMC_A[0..11]
SDRAM i
FMC_A[0..11]
FMC_D[0..15]
SDRAM i
FMC_D[0..15]
FMC_SDNWE
SDRAM i
FMC_SDNWE
FMC_SDNRAS
SDRAM i
FMC_SDNRAS
FMC_SDNCAS
SDRAM i
FMC_SDNCAS
FMC_SDCLK
SDRAM i
FMC_SDCLK
FMC_BA0
FMC_BA0
FMC_BA1
FMC_BA1
FMC_NBL0
FMC_NBL0
FMC_NBL1
FMC_NBL1
FMC_SDNE0
SDRAM i
FMC_SDNE0
FMC_SDCKE0
SDRAM i
FMC_SDCKE0
Matched Net Lengths [Tolerance = 100mil]
U_QSPI
QSPI.SchDoc
QSPI_NCS
QSPI i
QSPI_NCS
QSPI_CLK
QSPI i
QSPI_CLK
QSPI_D0
QSPI i
QSPI_D0
QSPI_D1
QSPI i
QSPI_D1
QSPI_D2
QSPI i
QSPI_D2
QSPI_D3
QSPI i
QSPI_D3
Matched Net Lengths [Tolerance = 100mil]
U_LCD-43
LCD-43.SchDoc
LCD_R[0..7]
LCD i
LCD_R[0..7]
LCD_G[0..7]
LCD i
LCD_G[0..7]
LCD_B[0..7]
LCD i
LCD_B[0..7]
LCD_BL_CTRL
LCD_BL_CTRL
LCD_HSYNC
LCD i
LCD_HSYNC
LCD_CLK
LCD i
LCD_CLK
LCD_VSYNC
LCD i
LCD_VSYNC
LCD_DISP
LCD_DISP
LCD_DE
LCD_DE
LCD_RST
LCD_RST
LCD_INT
LCD_INT
LCD_SDA
LCD_SDA
LCD_SCL
LCD_SCL
Matched Net Lengths [Tolerance = 100mil]
U_Ethernet
Ethernet.SchDoc
RMII_TXD0
RMII i
RMII_TXD0
RMII_TX_EN
RMII i
RMII_TX_EN
RMII_RXD0
RMII i
RMII_RXD0
RMII_REF_CLK
RMII i
RMII_REF_CLK
RMII_CRS_DV
RMII i
RMII_CRS_DV
RMII_MDC
RMII i
RMII_MDC
RMII_MDIO
RMII i
RMII_MDIO
NRST
NRST
RMII_TXD1
RMII i
RMII_TXD1
RMII_RXD1
RMII i
RMII_RXD1
OSC_25M
CLOCK i
OSC_25M
RMII_RXER
RMII_RXER
NRST
EXT_RST
EXT_SDA
EXT_SCL
uSD_CLK
uSD_CMD
uSD_D0
uSD_D1
uSD_D2
uSD_D3
uSD_Detect
B_USER
U_Peripherals
Peripherals.SchDoc
VCP_RX
VCP_TX
SWCLK
SWDIO
SWO
NRST
U_ST_LINK_V2-1
ST_LINK_V2-1.SCHDOC
SAI2_SCKA
SAI2_FSA
SAI2_SDA
SAI2_SDB
Audio_INT
AUDIO_SDA
AUDIO_SCL
SAI2_MCLKA
SPDIF_RX0
TP_PH15
U_AUDIO
AUDIO.SchDoc
NRST
EXT_RST
EXT_SDA
EXT_SCL
uSD_CLK
uSD_CMD
uSD_D0
uSD_D1
uSD_D2
uSD_D3
uSD_Detect
B_USER
VCP_RX
VCP_TX
SWCLK
SWDIO
SWO
NRST
SAI2_SCKA
SAI2_FSA
SAI2_SDA
SAI2_SDB
Audio_INT
AUDIO_SDA
AUDIO_SCL
SAI2_MCLKA
SPDIF_RX0
TP_PH15
Reference: MB1191
Date: 10/16/2015
Size: A4
Project: STM32F746G-DISCO
Sheet: 1 of 13
Revision: B-04
Title: STM32F746 Discovery Interconnexion
Rev A-01 --> PCB label MB1191 A-01
Rev B-01 --> PCB label MB1191 B-01, Ethernet modification, add SPDIF module,
Remove STPS1L30A for having 5V. Requiered on USB_VCC
Rev B-02 --> PCB label MB1191 B-02, Change Capacitors value for X3, X4.
Add R131, R135 of 100K
Rev B-03 --> PCB label MB1191 B-03, change only footprint for RCA
Rev B-04 --> PCB label MB1191 B-04, change footprint for JP2, CN3
and wiring around CN3, PA8 and PI0 labels inverted in CN4 and CN7
ARD_A[0..5]
ARD_D[0..15]
NRST
U_Arduino_ Connectors
Arduino_ Connectors.SchDoc
OTG_FS_PowerSwitchOn
OTG_FS_OverCurrent
OTG_FS_N
OTG_FS_P
OTG_FS_ID
OTG_FS_VBUS
U_USB_OTG_FS
USB_OTG_FS.SchDoc
ARD_A[0..5]
ARD_D[0..15]
NRST
OTG_FS_PowerSwitchOn
OTG_FS_OverCurrent
OTG_FS_N
OTG_FS_P
OTG_FS_ID
OTG_FS_VBUS
Matched Net Lengths [Tolerance = 100mil] Camera-Connectors
Camera-Connectors.SchDoc
OSC_24M
CLOCK i
OSC_24M
DCMI_NRST
DCMI_NRST
DCMI_D[0..7]
DCMII i
DCMI_D[0..7]
DCMI_PWR_EN
DCMI_PWR_EN
DCMI_VSYNC
DCMII i
DCMI_VSYNC
DCMI_HSYNC
DCMII i
DCMI_HSYNC
DCMI_PIXCK
DCMII i
DCMI_PIXCK
DCMI_SDA
DCMI_SDA
DCMI_SCL
DCMI_SCL
8
LCD_R[0..7]
LCD_G[0..7]
LCD_B[0..7]
LCD_BL_CTRL
LCD_HSYNC
LCD_CLK
LCD_VSYNC
LCD_DISP
LCD_DE
LCD_RST
LCD_INT
LCD_SDA
LCD_SCL
PA[0..15]
PB[0..15]
PC[0..15]
PD[0..15]
PE[0..15]
PF[0..15]
PG[0..15]
PH[0..15]
PI[0..15]
PJ[0..15]
PK[0..7]
Matched Net Lengths [Tolerance = 100mil] U_USB_OTG_HS
USB_OTG_HS.SchDoc
NRST
NRST
ULPI_D[0..7]
USB HS i
ULPI_D[0..7]
ULPI_CK
USB HS i
ULPI_CK
ULPI_DIR
USB HS i
ULPI_DIR
ULPI_NXT
USB HS i
ULPI_NXT
ULPI_STP
USB HS i
ULPI_STP
OTG_HS_OverCurrent
OTG_HS_OverCurrent
OSC_24M
CLOCK i
OSC_24M
Electrical schematics
UM1907
Electrical schematics
Figure 19. STM32F746 discovery interconnection
VCP_TX
VCP_RX
1
2
3
4
5
6
USB-MINI-typeB
VCC
DD+
ID
GND
SHELL
R128
1K5_1%_0402
USB_DM
USB_DP
T3
9013-SOT23
1
STLINK_RX
3V3_ST_LINK
USB
SB13
SB12
STLINK_TX
AIN_1
OSC_IN
OSC_OUT
STM_RST
NX3225GD-8.00M
3V3_ST_LINK
C98
R98
100nF
4K7_1%_0402
R97
4K7_1%_0402
5V_USB_ST_LINK
SB11
R99
100K_1%_0402
CN14
C100
[NA]
VBAT
PC13
PC14
PC15
OSCIN
OSCOUT
NRST
VSSA
VDDA
PA0
PA1
PA2
R129
36K_1%_0402
C113
C118
R139
330_1%_0402
LED_STLINK
330_1%_0402
R138
C109
3
2
36
35
34
33
32
31
30
29
28
27
26
25
4
5V
JP2
T_JTCK
T_JTMS
T_NRST
T_SWO
E5V
5V_ST_LINK
5V_USB_FS
5V_USB_HS
2
4
6
8
5V
1K
R86
3V3_ST_LINK
PWR_ENn
3
E5V
C41
10uF_X5R_10%_0805
LD1117S50TR
2
Vin
Vout
4
Tab
U6
Arduino UNO power pin
C29
10uF_X5R_10%_0805
VIN
ST890CDR
SB16
SB17
PB3
PA14
PA13
STM_JTCK
SWCLK
SB15
SB14
CN8
STM_JTMS
SWDIO
SWCLK
SWDIO
NRST
SWO
SWD
6
1
3V3
3
VI
EN
U7
100nF
C61
5V
Vin
Vout
Tab
U13
LD1117S18TR
NC
PG
VO
LD39050PU33R
10nF
C94
BYPASS
Vout
Reference: MB1191
Date: 10/16/2015
Size: A4
Project: STM32F746G-DISCO
5
1V8
1.8 Volts Output
C68
100nF
3V3
3.3 Volts Output
100nF
C85
3V3_ST_LINK
ST-LINK Power
C108
10uF_X5R_10%_0603
Sheet: 2 of 13
Revision: B-04
2
4
1uF
C75
5
3
4
1uF
C86
Title: ST-LINK/V2-1 with support of SWD only
1uF
C62
INH
GND
Vin
U12 LD3985M33R
C84
100nF
3
1
5 Volts Output
1uF
C91
SB10
Not Fitted, must be on a border or the PCB.
3V3_ST_LINK
D4
BAT60JFILM
D3
BAT60JFILM
D1
BAT60JFILM
D2
BAT60JFILM
LED, red
LD2
Ilim = 510mA
1.2Ilim = 612mA < Isc < 1.5Ilim = 765mA
U8
SB9
R72
1
6
IN
OUT
2
7
C76
IN
OUT
100K_1%_0402
R79
100nF
8
5
FAULT
SET
R60
2K7
10K_1%_0402
3
4
ON
GND
5V_ST_LINK
5V_USB_ST_LINK
E5V
5V_USB_FS
5V_USB_HS
TSM-104-01-x-DV
1
3
5
7
JP1
5 Volts Power Supply
Not Fitted, must be on a border or the PCB.
E5V
5V_USB_ST_LINK
STM_JTMS
USB_DP
USB_DM
T_SWO
LED_STLINK
MCO
PWR_ENn
R127
T_JTMS
T_JTCK
100_1%_0402
T_SWDIO_IN
3V3_ST_LINK
U14
STM32F103CBT6
Not Fitted
LD_BICOLOR_CMS
_Green
Red
LD7
COM
1
3V3_ST_LINK
VDD_2
VSS_2
JTMS/SWDIO
PA12
PA11
PA10
PA9
PA8
PB15
PB14
PB13
PB12
BAT60JFILM
3V3_ST_LINK
USB_RENUMn
STM_JTCK
0
R109
100nF 100nF 100nF 100nF
C101
3V3_ST_LINK
R118 USB_RENUMn
100_1%_0402
R120
10K_1%_0402
1
2
3
4
5
6
7
8
9
10
11
12
3V3_ST_LINK
100K_1%_0402
R100
10K_1%_0402
10pF X4
10pF
3V3_ST_LINK1
2
C99
Board Ident: PC13=0
R105
D6
2K7_1%_0402
R108
1
2
3
4
R101
3
2
PWR_EXT
48
47
46
45
44
43
42
41
40
39
38
37
VDD_3
VSS_3
PB9
PB8
BOOT0
PB7
PB6
PB5
PB4/JNTRST
PB3/JTDO
PA15/JTDI
JTCK/SWCLK
PA3
PA4
PA5
PA6
PA7
PB0
PB1
PB2/BOOT1
PB10
PB11
VSS_1
VDD_1
13
14
15
16
17
18
19
20
21
22
23
24
T_JTCK
T_JTDO
T_JTDI
T_NRST
T_JRST
4
R112
4K7_1%_0402
1
2
GND
2
GND
7
DocID027942 Rev 2
1
UM1907
Electrical schematics
Figure 20. ST-LINK/V2-1 with support of SWD only
27/49
48
EXT_SDA
EXT_SCL
EXT_SDA
EXT_SCL
3V3
2
4
6
8
3V3
R12
[NA]
3V3
3V3
0_5%_0402
R11
CN3
PJS008-2003
R16
R14
47K_1%_0402
47K_1%_0402
R15
R13
47K_1%_0402
47K_1%_0402
R17
47K_1%_0402
Input pin with pull-up
uSD_Detect
uSD_D0
uSD_D1
uSD_D2
uSD_D3
uSD_CLK
uSD_CMD
MICRO SD
(TF) Card
5V
EXT_RST
SMS064FF or SMS128FF
EXT_RST
SB2
F206A-2*04MGF-A
1
3
5
7
CN2
EXT/RF E2P Connector
1
2
3
4
5
6
7
8
SW2
SW1
DocID027942 Rev 2
9
10
NRST
B_USER
SB6
C10
100nF
10K
R18
100nF
C25
SB7
Reference: MB1191
Date: 10/16/2015
Size: A4
Project: STM32F746G-DISCO
VDD
R19
10K
Sheet: 3 of 13
Revision: B-04
Title: Joystick, ACP, LEDs and Push Button
B_USER
USER & WAKE-UP Button
RESET Button
NRST
R39
10K_1%_0402
3V3
4
1
3
2
4
1
B1
SW-PUSH-CMS_BLUE
B2
SW-PUSH-CMS_BLACK
28/49
3
2
Not Fitted
Electrical schematics
UM1907
Figure 21. Joystick, LEDs and pushbutton
100nF C30
5
1
5
1
LR
CLK
DOUT
LR
CLK
DOUT
LEFT
MP34DT01
GND
VDD
U21
MP34DT01
GND
VDD
10K
RIGHT
U20
2
1
RCA_SMD
CN1
R6
75
C6
22nF
RCA in Yellow for SPDIF input
100nF C77
R47
100nF C103
R7
100
2
3
4
2
3
4
2
1M
3V3
100nF C70
C104
4.7uF
3
6
MIC_VDD
3V3
100nF
C4
C89
R87
C106
C107
100nF
C7
MIC_DATA
Right
Left
Very close to Output pin 4
of first stage
[NA]
R8
4
2
PJ3028B-3_BE
CN11
Jack in blue
C9
22nF
74LVC1G04SE
U1
4
C93
4.7uF
C79
4.7uF
C71
1uF
R9
C69
1uF
SAI2_SCKA
SAI2_FSA
SAI2_SDA
SAI2_SDB
Audio_INT
MIC_CLK
3V3
A8
A9
C7
B7
B8
B9
C8
D7
F6
H5
H4
F5
H2
F4
H3
E5
G4
C6
G1
E3
E4
F2
G3
D4
D5
E6
2
3V3
R22
1M
U2
4
74LVC1G04SE
WM8994ECS/R
IN2RP/VRXP
IN2RN/DMICDAT2
IN1RP
IN1RN
IN2LP/VRXN
IN2LN/DMICDAT1
IN1LP
IN1LN
GPIO11/BCLK3
GPIO10/LRCLK3
GPIO8/DACDAT3
GPIO9/ADCDAT3
GPIO3/BCLK2
GPIO4/LRCLK2
GPIO5/DACDAT2
GPIO7/ADCDAT2
GPIO6/ADCLRCLK2
DMICCLK
BCLK1
LRCLK1
DACDAT1
ADCDAT1
ADCLRCLK1/GPIO1
LDO1ENA
LDO2ENA
VREFC
LDO1VDD
AVDD1
SPKVDD1
SPKVDD2
AVDD2
CPVDD
DCVDD
DBVDD
LDO2VDD
U11
Second Stage
R10
100
1uF
1uF
1uF
10K
E9
D9
B2
C2
D8
G9
F1
D2
D1
4.7uF
C105
[NA]
H7
G7
G8
H8
C80
C78
2.2uF
2.2uF
TP_PH15
Left
Right
TP_PH15
SPK Right
SPK Left
SAI2_MCLKA
AUDIO_SDA
AUDIO_SCL
Reference: MB1191
Date: 10/16/2015
Size: A4
Project: STM32F746G-DISCO
Jack out Green
6
3
PJ3028B-3_GR
2 CN10
4
Sheet: 4 of 13
Revision: B-04
Title: Audio Codec WOLFSON and connectors
TP3
JP3
R102
20
C3
B3
2.2uF
0
0
4.7uF
C88
3V3
R83
R76
JP4
C87
R121
20
R80
Default I2C Address : 00110100
B1
A2
C5
B5
C4
B4
A6
G5
G6
H6
F9
F8
A7
B6
C9
D3
E1
A3
A5
F3
H1
G2
A4
D6
E7
E8
A1
C1
H9
E2
F7
SPDIF_RX0
CPVOUTN
CPVOUTP
CPCA
CPCB
SPKOUTRN
SPKOUTRP
SPKOUTLN
SPKOUTLP
LINEOUT1N
LINEOUT1P
LINEOUT2N
LINEOUT2P
LINEOUTFB
HPOUT1FB
HPOUT1R
HPOUT1L
HPOUT2N
HPOUT2P
MICBIAS1
MICBIAS2
VMIDC
MCLK1
GPIO2/MCLK2
SPKMODE
REFGND
SDA
SCLK
CS/ADDR
CIFMODE
AGND
AGND
AGND
SPKGND1
SPKGND2
CPGND
DGND
HP2GND
100nF C115
1V8
100nF C92
First Stage
5
3
100nF C102
3V3
5
DocID027942 Rev 2
3
UM1907
Electrical schematics
Figure 22. Audio codec Cirrus and connectors
29/49
48
100nF C72
30/49
QSPI_D0
QSPI_D1
QSPI_D2
QSPI_D3
QSPI_NCS
QSPI_CLK
1
6
5
2
3
7
QSPI_NCS
QSPI_CLK
QSPI_D0
QSPI_D1
QSPI_D2
QSPI_D3
VSS
VCC
4
8
10K_1%_0402
N25Q128A13EF840E (MICRON)
DQ0
DQ1
DQ2/Vpp/W#
DQ3/HOLD#
S#
C
U3
R57
3V3
Quad SPI Flash Memory
C38
100nF_X7R_10%_0402
DocID027942 Rev 2
Reference: MB1191
Date: 10/16/2015
Size: A4
Project: STM32F746G-DISCO
Sheet: 5 of 13
Revision: B-04
Title: Quad SPI Flash Memory (MICRON)
Electrical schematics
UM1907
Figure 23. Quad-SPI Flash memory (MICRON)
DocID027942 Rev 2
SB3
PF6
PB8
ADC3_IN4 ARD_A5
SCL/D15
SB1
SB4
PB9
ARD_D14
SDA/D14
ARD_D15
SB5
PF7
ADC3_IN5 ARD_A4
VIN
3V3
5V
NRST
PA0
PF10
PF9
PF8
NRST
ARD_D[0..15]
ARD_A[0..5]
ARD_A0
ARD_A1
ARD_A2
ARD_A3
ADC3_IN0
ADC3_IN8
ADC3_IN7
ADC3_IN6
ARD_D[0..15]
IOREF
NRST
3V3
5V
GND
GND
VIN
A0
A1
A2
A3
A4
A5
F201-1*06MGF-W1-BA
1
2
3
4
5
6
F201-1*08MGF-W1-BA
CN5
1
2
3
4
5
6
7
8
CN6
LED, green
LD1
POWER
AIN
ARD_A[0..5]
D7
PWM/D6
PWM/CS/D5
D4
PWM/D3
D2
TX/D1
RX/D0
SCL/D15
SDA/D14
AVDD
GND
SCK/D13
MISO/D12
PWM/MOSI/D11
PWM/D10
PWM/D9
D8
R59
510_1%_0402
PI1
PB14
PB15
PA8
PA15
PI2
PB8
PB9
ARD_D13
ARD_D12
ARD_D11
ARD_D10
ARD_D9
ARD_D8
ARD_D15
ARD_D14
F201-1*08MGF-W1-BA
F201-1*10MGF-W1-BA
CN4
ARD_D7
PI3
8
PH6 ARD_D6
7
ARD_D5
PI0
6
PG7 ARD_D4
5
PB4 ARD_D3
4
PG6 ARD_D2
3
PC6 ARD_D1
2
PC7 ARD_D0
1
10
9
8
7
6
5
4
3
2
1
CN7
SB8
Arduino UNO connector
C90
[NA]
VREF+
Reference: MB1191
Date: 10/16/2015
Size: A4
Project: STM32F746G-DISCO
Title: Arduino UNO connectors
USART6_TX
USART6_RX
TIM3_CH1
TIM12_CH1
TIM5_CH4, SPI2_NSS
SPI2_SCK
SPI2_MISO
TIM12_CH2, SPI2_MOSI
TIM1_CH1
TIM2_CH1
0
R96
Revision: B-04
Sheet: 6 of 13
UM1907
Electrical schematics
Figure 24. Arduino Uno connectors
31/49
48
32/49
DocID027942 Rev 2
3V3
C34
100nF_X7R_10%_0402
C51
100nF_X7R_10%_0402
C15
100nF_X7R_10%_0402
C28
100nF_X7R_10%_0402
C42
100nF_X7R_10%_0402
C46
100nF_X7R_10%_0402
C52
100nF_X7R_10%_0402
Place close SDRAM
C16
100nF_X7R_10%_0402
C43
100nF_X7R_10%_0402
K8
K7
J9
J8
J2
J1
FMC_SDNWE
FMC_SDNCAS
FMC_SDNRAS
FMC_SDNE0
FMC_SDCKE0
FMC_SDCLK
A7
F9
L7
R7
B2
B7
C9
D9
E1
L1
M9
N9
P2
P7
E3
E7
H3
H7
K3
K2
F2
F8
K1
K9
H8
J7
FMC_BA1
FMC_BA0
10K_1%_0402
R56
10K_1%_0402
FMC_NBL1
FMC_NBL0
FMC_NBL1
FMC_NBL0
C26
100nF_X7R_10%_0402
C27
100nF_X7R_10%_0402
C31
100nF_X7R_10%_0402
C45
100nF_X7R_10%_0402
C50
100nF_X7R_10%_0402
R55
FMC_SDNWE
FMC_SDNCAS
FMC_SDNRAS
FMC_SDNE0
FMC_SDCKE0
FMC_SDCLK
FMC_BA1
FMC_BA0
H9
G7
J3
H2
H1
G3
G2
G1
F3
F7
G9
G8
FMC_A11
FMC_A10
FMC_A9
FMC_A8
FMC_A7
FMC_A6
FMC_A5
FMC_A4
FMC_A3
FMC_A2
FMC_A1
FMC_A0
VSS
VSS
VSS
VSS
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
VSSQ
DQ15
DQ14
DQ13
DQ12
DQ11
DQ10
DQ9
DQ8
DQ7
DQ6
DQ5
DQ4
DQ3
DQ2
DQ1
DQ0
DQ31
DQ30
DQ29
DQ28
DQ27
DQ26
DQ25
DQ24
DQ23
DQ22
DQ21
DQ20
DQ19
DQ18
DQ17
DQ16
A3
F1
L3
R3
B3
B8
C1
D1
E9
L9
M1
N1
P3
P8
R2
N3
R1
N2
P1
M2
M3
L2
L8
M7
M8
P9
N8
R9
N7
R8
E2
D3
D2
B1
C2
A1
C3
A2
A8
C7
A9
C8
B9
D8
D7
E8
FMC_D15
FMC_D14
FMC_D13
FMC_D12
FMC_D11
FMC_D10
FMC_D9
FMC_D8
FMC_D7
FMC_D6
FMC_D5
FMC_D4
FMC_D3
FMC_D2
FMC_D1
FMC_D0
R51
R37
R27
R26
R36
R40
R49
R52
MT48LC4M32B2B5-6A (MICRON)
VDD
VDD
VDD
VDD
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
NC
NC
NC
NC
NC
NU
DQM3
DQM2
DQM1
DQM0
WE#
CAS#
RAS#
CS#
CKE
CLK
BA1
BA0
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
U4
10K_1%_0402
R48
10K_1%_0402
10K_1%_0402
R43
10K_1%_0402
10K_1%_0402
R23
10K_1%_0402
10K_1%_0402
R24
10K_1%_0402
10K_1%_0402
R25
10K_1%_0402
10K_1%_0402
R41
10K_1%_0402
10K_1%_0402
R50
10K_1%_0402
10K_1%_0402
R53
10K_1%_0402
FMC_D[0..15]
FMC_A[0..11]
Reference: MB1191
Date: 10/16/2015
Size: A4
Project: STM32F746G-DISCO
Title: SDRAM (MICRON)
FMC_D[0..15]
FMC_A[0..11]
Revision: B-04
Sheet: 7 of 13
Electrical schematics
UM1907
Figure 25. SDRAM (MICRON)
SB18
OTG_FS_VBUS
OTG_FS_N
OTG_FS_P
OTG_FS_ID
5V_USB_FS
OTG_FS_PowerSwitchOn
R133
0
0_5%_0402
R117
10K_1%_0402
B3
C3
D3
A2
B2
5V
R116
3V3
0
0
GND
ID
D+in
D-in
Pd1
Pd2
R132
R125
D2
A3
C1
D1
B1
C2
STMPS2141STR
3
1
47K_1%_0402
GND FAULT
IN
OUT
EN
EMIF02-USB03F2
Vbus
D+out
D-out
Dz
Pup
U18
2
5
4
U16
0_5%_0402
R119
LD6
LED, red
R137
620_1%_0603
47K_1%_0402
USB_FS1_N
USB_FS1_P
C112
4.7uF_X5R_10%_0603
R126
100K
R135
1
R134
6
1
2
3
4
5
T2
9013-SOT23
LD5
LED, green
Reference: MB1191
Date: 10/16/2015
Size: A4
Project: STM32F746G-DISCO
Sheet: 8 of 13
Revision: B-04
Title: USB OTG FS with Micro A-B connector
USB-MICRO-AB
Shield
VBUS
DM
DP
ID
GND
CN13
OTG_FS_OverCurrent
R136
330_1%_0603
3V3
3
DocID027942 Rev 2
2
USB_Micro-AB receptacle
3V3
UM1907
Electrical schematics
Figure 26. USB OTG FS with micro A-B connector
33/49
48
34/49
DocID027942 Rev 2
4
NRST
100nF
GND
3
2
100nF
100nF
C22
100nF
C23
100nF
100nF
C21
100nF
C57
LCD_RST
R34
10K_1%_0402
3V3
NZ2520SB-25.00M
EN
OUT
QSPI_CLK
100nF
C20
100nF
C58
OTG_FS_ID
OTG_FS_N
OTG_FS_P
SWDIO
SWCLK
ARD_D9
100nF
C19
0
100nF
C18
100nF
C40
3V3
100nF
C32
100nF
C37
R42
[NA]
3V3
100nF
C35
100nF
FMC_A[0..11]
FMC_D[0..15]
FMC_SDNWE
FMC_SDNRAS
FMC_SDNCAS
FMC_SDCLK
FMC_BA0
FMC_BA1
FMC_SDNE0
FMC_SDCKE0
FMC_NBL0
FMC_NBL1
PDR_ON
NRST
BOOT0
PH0-OSC_IN
PH1-OSC_OUT
PC14-OSC32_IN
PC15-OSC32_OUT
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
PB8
PB9
PB10
PB11
PB12
PB13
PB14
PB15
100nF
C39
100nF
C33
100nF
C44
C54
4.7uF
VDD
PK0
PK1
PK2
PK3
PK4
PK5
PK6
PK7
PJ0
PJ1
PJ2
PJ3
PJ4
PJ5
PJ6
PJ7
PJ8
PJ9
PJ10
PJ11
PJ12
PJ13
PJ14
PJ15
C8
1uF
VDDA
G13
F12
F13
D8
D7
C6
C5
C4
R6
R7
P7
N8
M9
M14
K12
J12
H12
J13
H13
G12
B10
B9
C9
D10
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
PC8
PC9
PC10
PC11
PC12
PC13
100nF
VREF+
VDDA
VDD
LCD_G5
LCD_G6
LCD_G7
LCD_BL_CTRL
LCD_B5
LCD_B6
LCD_B7
LCD_DE
LCD_R1
LCD_R2
LCD_R3
LCD_R4
LCD_R5
LCD_R6
LCD_R7
LCD_G0
LCD_G1
LCD_G2
LCD_G3
LCD_G4
R58
LCD_B1
LCD_B2
LCD_B3
SWDIO
SWCLK
SWO
VCP_RX
VCP_TX
B_USER
EXT_SCL
EXT_SDA
EXT_RST
OTG_FS_VBUS
C17
1uF
R28
0
100nF
C24
VDD
VDD
L1
FCM1608KF-601T03
R21
0
3V3
100
SWDIO
SWCLK
SWO
VCP_RX
VCP_TX
B_USER
EXT_SCL
EXT_SDA
EXT_RST
ULPI_STP
RMII_MDC
ULPI_DIR
FMC_SDCKE0
RMII_RXD0
RMII_RXD1
ARD_D1
ARD_D0
uSD_D0
uSD_D1
uSD_D2
uSD_D3
uSD_CLK
uSD_Detect
C11
FMC_A[0..11]
FMC_D[0..15]
FMC_SDNWE
FMC_SDNRAS
FMC_SDNCAS
FMC_SDCLK
FMC_BA0
FMC_BA1
FMC_SDNE0
FMC_SDCKE0
FMC_NBL0
FMC_NBL1
M2
M3
M4
L4
N5
P5
H15
G15
G14
F14
B14
B13
A12
D1
C14
4.7uF
PK0
PK1
PK2
PK3
PK4
PK5
PK6
PK7
PJ0
PJ1
PJ2
PJ3
PJ4
PJ5
PJ6
PJ7
PJ8
PJ9
PJ10
PJ11
PJ12
PJ13
PJ14
PJ15
PA0-WKUP
PC0
PA1
PC1
PA2
PC2
PA3
PC3
PA4
PC4
PA5
PC5
PA6
PC6
PA7
PC7
PA8
PC8
PA9
PC9
PA10
PC10
PA11
PC11
PA12
PC12
PA13
PC13-ANTI_TAMP
PA14
PA15
U5A
STM32F746NGH6
R38
10K_1%_0402
E5
C36
R35
[NA]
J1
E6
BOOT0
E1
F1
PC14
PC15
G1
H1
R5
R4
M5
A10
A9
A8
B6
B5
A7
B4
P12
R13
L13
K14
R14
R15
N3
N2
P2
R2
N4
P4
P3
R3
F15
E15
D15
C15
B15
A15
A14
A13
PB0
PB1
R44
PB3
PB4
PB5
PB6
PB7
PB8
PB9
PB10
PB11
PB12
PB13
PB14
PB15
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
PA8
PA9
PA10
PA11
PA12
PA13
PA14
PA15
uSD_CLK
uSD_CMD
uSD_D0
uSD_D1
uSD_D2
uSD_D3
uSD_Detect
QSPI_D3
QSPI_D2
QSPI_D1
QSPI_D0
QSPI_CLK
QSPI_NCS
PH0
PH1
R45
10K_1%_0402
100_1%_0402
R30
100nF
C59
DCMI_NRST
OSC_25M
0
4.7pF_NPO_-+0.25pF_0402
VDD
X2
R54
3V3
0
4.7pF_NPO_-+0.25pF_0402
X3
NX3215SA-32.768K
C12
R31
C56
VDD
R64
ARD_A0
RMII_REF_CLK
RMII_MDIO
ULPI_D0
DCMI_HSYNC
ULPI_CK
DCMI_PIXCK
RMII_CRS_DV
ARD_D10
uSD_CLK
uSD_CMD
uSD_D0
uSD_D1
uSD_D2
uSD_D3
uSD_Detect
QSPI_D3
QSPI_D2
QSPI_D1
QSPI_D0
QSPI_CLK
QSPI_NCS
ULPI_D1
ULPI_D2
PB2
SWO
ARD_D3
ULPI_D7
2K7_1%_0402 2K7_1%_0402
QSPI_NCS
VCP_RX
EXT_SCL DCMI_SCL ARD_D15
EXT_SDA DCMI_SDA ARD_D14
ULPI_D3
ULPI_D4
ULPI_D5
ULPI_D6
ARD_D12
ARD_D11
C13
R32
R46
3V3
C55
VDD
0
OTG_FS_VBUS
R63
[NA]
VCP_TX
AUDIO_SDA
AUDIO_SCL
SAI2_MCLKA
SAI2_SCKA
SAI2_FSA
SAI2_SDA
SAI2_SDB
TP_PH15
Audio_INT
SPDIF_RX0
OSC_25M
ARD_A[0..5]
ARD_D[0..15]
NRST
1
10K_1%_0402
R5
C5
3V3
AUDIO_SDA
AUDIO_SCL
SAI2_MCLKA
SAI2_SCKA
SAI2_FSA
SAI2_SDA
SAI2_SDB
TP_PH15
Audio_INT
SPDIF_RX0
OSC_25M
ARD_A[0..5]
ARD_D[0..15]
R20
10K
C1
L5
R1
P1
L10
F11
E7
K5
H5
L8
L9
J11
G11
E9
E8
J5
F4
K11
E10
F5
G5
L7
H11
STM32F746NGH6
VBAT
BYPASS-REG
VDDA
VREF+
VSSA
VREFVCAP1
VCAP2
C48
2.2uF
C47
2.2uF
Ceramic capacitor (Low ESR)
L11
E11
M1
N1
L6
H10
K9
F10
F6
K6
H6
K7
K8
J10
G10
F8
F7
J6
F2
K10
F9
G6
FMC_A0
FMC_A1
FMC_A2
FMC_A3
FMC_A4
FMC_A5
ARD_A5
ARD_A4
ARD_A3
ARD_A2
ARD_A1
FMC_SDNRAS
FMC_A6
FMC_A7
FMC_A8
FMC_A9
FMC_NBL0
FMC_NBL1
QSPI_D2
OTG_HS_OverCurrent
LCD_B0
DCMI_D6
DCMI_D7
FMC_D4
FMC_D5
FMC_D6
FMC_D7
FMC_D8
FMC_D9
FMC_D10
FMC_D11
FMC_D12
B12
C12
D12
C11
D11
C10
B11
A11
L15
L14
K15
N10
M10
M11
L12
K13
PF0
PF1
PF2
PF3
PF4
PF5
PF6
PF7
PF8
PF9
PF10
PF11
PF12
PF13
PF14
PF15
D2
E2
G2
H2
J2
K3
K2
K1
L3
L2
L1
P8
M6
N6
P6
M8
PE0
A6
PE1
A5
PE2
A3
PE3
A2
PE4
A1
PE5
B1
PE6
B2
PE7
R8
PE8
N9
PE9
P9
PE10 R9
PE11 P10
PE12 R10
PE13 R12
PE14 P11
PE15 R11
PD0
PD1
PD2
PD3
PD4
PD5
PD6
PD7
PD8
PD9
PD10
PD11
PD12
PD13
PD14
PD15
DCMI_NRST
DCMI_D[0..7]
DCMI_PWR_EN
DCMI_VSYNC
DCMI_HSYNC
DCMI_PIXCK
DCMI_SDA
DCMI_SCL
RMII_RXER
RMII_TXD0
RMII_TX_EN
RMII_RXD0
RMII_REF_CLK
RMII_CRS_DV
RMII_MDC
RMII_MDIO
RMII_TXD1
RMII_RXD1
FMC_D2
FMC_D3
uSD_CMD
DCMI_D5
OTG_FS_OverCurrent
OTG_FS_PowerSwitchOn
Audio_INT
SPDIF_RX0
FMC_D13
FMC_D14
FMC_D15
QSPI_D0
QSPI_D1
QSPI_D3
FMC_D0
FMC_D1
OTG_HS_OverCurrent
ULPI_DIR
ULPI_STP
ULPI_NXT
ULPI_CK
ULPI_D[0..7]
OTG_FS_PowerSwitchOn
OTG_FS_OverCurrent
OTG_FS_N
OTG_FS_P
OTG_FS_ID
OTG_FS_VBUS
VDD1
VSS1
VDD2
VSS2
VDD3
VSS3
VDD4
VSS4
VDD5
VSS5
VDD6
VSS6
VDD7
VSS7
VDD8
VSS8
VDD_USB33
VSS9
VDD10
VSS10
VDD11
VSS11
VDD12
VSS12
VDD13
VSS13-VSS18
VDD14
VSS14
VDD15
VSS15
VDD17
VSS17
VDD18
VDD19
VSS19
VDD20
VSS20
U5C
OTG_HS_OverCurrent
ULPI_DIR
ULPI_STP
ULPI_NXT
ULPI_CK
ULPI_D[0..7]
OTG_FS_PowerSwitchOn
OTG_FS_OverCurrent
OTG_FS_N
OTG_FS_P
OTG_FS_ID
OTG_FS_VBUS
PH2
PH3
PH4
PH5
PH6
PH7
PH8
PH9
PH10
PH11
PH12
PH13
PH14
PH15
PG0
PG1
PG2
PG3
PG4
PG5
PG6
PG7
PG8
PG9
PG10
PG11
PG12
PG13
PG14
PG15
E14
D14
C14
C13
C3
D3
D6
D4
C2
E4
D5
F3
E3
G3
H3
G4
K4
J4
H4
J3
P13
N13
P14
N14
P15
N15
M15
E12
E13
D13
N7
M7
M13
M12
N12
N11
J15
J14
H14
D9
C8
B8
C7
B3
A4
B7
PF[0..15]
PE[0..15]
PD[0..15]
PC[0..15]
PB[0..15]
PA[0..15]
PI0
PI1
PI2
PI3
PI4
PI5
PI6
PI7
PI8
PI9
PI10
PI11
PI12
PI13
PI14
PI15
PH2
PH3
PH4
PH5
PH6
PH7
PH8
PH9
PH10
PH11
PH12
PH13
PH14
PH15
PG0
PG1
PG2
PG3
PG4
PG5
PG6
PG7
PG8
PG9
PG10
PG11
PG12
PG13
PG14
PG15
PF[0..15]
PE[0..15]
PD[0..15]
PC[0..15]
PB[0..15]
PA[0..15]
ARD_D5
ARD_D13
ARD_D8
ARD_D7
SAI2_MCLKA
SAI2_SCKA
SAI2_SDA
SAI2_FSA
NC1
LCD_VSYNC
LCD_HSYNC
B_USER
LCD_DISP
LCD_INT
LCD_CLK
LCD_R0
Date: 10/16/2015
Reference: MB1191
Project: STM32F746G-DISCO
Size: A3
LCD_R[0..7]
LCD_G[0..7]
LCD_B[0..7]
LCD_BL_CTRL
LCD_HSYNC
LCD_CLK
LCD_VSYNC
LCD_DISP
LCD_DE
LCD_RST
LCD_INT
LCD_SDA
LCD_SCL
PK[0..7]
PJ[0..15]
PI[0..15]
PH[0..15]
PG[0..15]
100
Sheet: 9 of 13
Revision: B-04
R33
PK[0..7]
PJ[0..15]
PI[0..15]
PH[0..15]
PG[0..15]
TP
TP2
3V3
3V3
TP1
NC2
R29
100
FMC_SDNE0
TP
R62
R61
ULPI_NXT
2K7_1%_0402
FMC_SDNWE
2K7_1%_0402
ARD_D6
AUDIO_SCL
LCD_SCL
AUDIO_SDA
LCD_SDA
DCMI_D0
DCMI_D1
DCMI_D2
DCMI_D3
DCMI_PWR_EN
DCMI_D4
TP_PH15
FMC_A10
FMC_A11
RMII_RXER
EXT_RST
FMC_BA0
FMC_BA1
ARD_D2
ARD_D4
FMC_SDCLK
DCMI_VSYNC
SAI2_SDB
RMII_TX_EN
LCD_B4
RMII_TXD0
RMII_TXD1
FMC_SDNCAS
LCD_R[0..7]
LCD_G[0..7]
LCD_B[0..7]
LCD_BL_CTRL
LCD_HSYNC
LCD_CLK
LCD_VSYNC
LCD_DISP
LCD_DE
LCD_RST
LCD_INT
LCD_SDA
LCD_SCL
Title: STM32F746NGH6 Connexion
PI0
PI1
PI2
PI3
PI4
PI5
PI6
PI7
PI8-ANTI_TAMP2
PI9
PI10
PI11
PI12
PI13
PI14
PI15
STM32F746NGH6
PF0
PF1
PF2
PF3
PF4
PF5
PF6
PF7
PF8
PF9
PF10
PF11
PF12
PF13
PF14
PF15
PE0
PE1
PE2
PE3
PE4
PE5
PE6
PE7
PE8
PE9
PE10
PE11
PE12
PE13
PE14
PE15
PD0
PD1
PD2
PD3
PD4
PD5
PD6
PD7
PD8
PD9
PD10
PD11
PD12
PD13
PD14
PD15
U5B
DCMI_NRST
DCMI_D[0..7]
DCMI_PWR_EN
DCMI_VSYNC
DCMI_HSYNC
DCMI_PIXCK
DCMI_SDA
DCMI_SCL
RMII_RXER
RMII_TXD0
RMII_TX_EN
RMII_RXD0
RMII_REF_CLK
RMII_CRS_DV
RMII_MDC
RMII_MDIO
RMII_TXD1
RMII_RXD1
Electrical schematics
UM1907
Figure 27. STM32F746NGH6 connection
NRST
OSC_24M
ULPI_NXT
ULPI_DIR
ULPI_STP
ULPI_CK
OSC_24M
ULPI_D[0..7]
25
26
R114
27
15
16
13
10
9
7
6
5
4
3
ULPI_D7
ULPI_D6
ULPI_D5
ULPI_D4
ULPI_D3
ULPI_D2
ULPI_D1
ULPI_D0
100_1%_0402
2
31
29
1
ULPI_NXT
ULPI_DIR
ULPI_STP
ULPI_CK
USB3320C-EZK
RESETB
SPK_L
SPK_R
XO
REFCLK
D7
D6
D5
D4
D3
D2
D1
D0
NXT
DIR
STP
CLKOUT
U15
GNDPAD
VDD3.3
VDD1.8
VDD1.8
VDDIO
REFSEL0
REFSEL1
REFSEL2
NC
VBUS
DM
DP
ID
CPEN
VBAT
RBIAS
33
20
30
28
32
8
11
14
12
22
19
18
23
17
21
24
C117
100nF
8K06_1%_0402
R115
R123
USB_HS_N
USB_HS_P
D8
USBULC6-2F3
R106
[NA]
R103
[NA]
R111
[NA]
R113
0_5%_0402
REFSEL2
C119
2.2uF_X7R_10%_0805
R110
0_5%_0402
REFSEL1
C116
100nF
R104
0_5%_0402
REFSEL0
3V3
C110
100nF
1V8
3
1
820_1%_0805
STMPS2151STR
GND FAULT
IN
OUT
EN
U17
i
i Diff Pair 90ohm
Diff Pair 90ohm
Matched Net Lengths [Tolerance = 150mil]
REFSEL0
REFSEL1
REFSEL2
3V3
R107
C111
100nF
0_5%_0402
5V
5V
2
5
4
3K3
47K_1%_0402
R124
Shield
Shield
Shield
Shield
EXP
475900001
L7
BLM18PG121SN1D
6
7
8
9
10
T1
9013-SOT23
LD4
LED, green
R141
330_1%_0402
3V3
Reference: MB1191
Date: 10/16/2015
Size: A4
Project: STM32F746G-DISCO
Sheet: 10 of 13
Revision: B-04
Title: USB OTG HS PHY with Micro A-B connector
100nF100nF100nF100nF
C123 C121 C120 C122
D7
ESDA14V2-2BF3
100K
R131
1
OTG_HS_OverCurrent
4.7uF_X5R_10%_0603
C114
620_1%_0603
R140
3V3
L6
5V_USB_HS
BLM18PG121SN1D
CN12
1
VBUS
2
DM
3
DP
4
ID
5
GND
LED, red
LD3
R122
0
3
2
ULPI_D[0..7]
A2
A1
B2
B1
A2
A1
B2
B1
DocID027942 Rev 2
USB_Micro-AB receptacle
R130
UM1907
Electrical schematics
Figure 28. USB OTG HS PHY with micro A-B connector
35/49
48
36/49
DocID027942 Rev 2
OSC_25M
NRST
RMII_REF_CLK
RMII_MDC
RMII_MDIO
RMII_CRS_DV
RMII_RXD0
RMII_RXD1
RMII_RXER
RMII_TX_EN
RMII_TXD0
RMII_TXD1
OSC_25M
33
R66
100
R78
33
33
R69
R71
R65
1K5
R77
4K7
R70
4K7
R68
4K7
R73
4K7
R67
4K7
3V3
4
5
15
14
13
12
11
8
7
10
16
17
18
LAN8742A-CZ-TR
XTAL2
XTAL1/CLKIN
nRST
nINT/REFCLK0
MDC
MDIO
CRS_DV/MODE2
RXD0/MODE0
RXD1/MODE1
RXER/PHYAD0
TXEN
TXD0
TXD1
U9
R92
50
GND_EP
25
470pF
C66
C67
1uF
C74
C73
100nF 100nF 10uF
C81
100nF
C60
R95
10K
R88
10K
TD_P
TD_N
RD_P
RD_N
R89
330
R94
330
Reference: MB1191
Date: 10/16/2015
Size: A4
Project: STM32F746G-DISCO
9
10
13
14
12
11
1
2
7
6
8
3
5
4
HR961160C
NC
CHS GND
Shield
Shield
LED(green)_A
LED(green)_K
LED(Yellow)_A
LED(Yellow)_K
RD+
RCT
RD-
TD+
TCT
TD-
CN9
C82
C83
100nF 100nF
Sheet: 11 of 13
Revision: B-04
Title: Ethernet PHY with RJ45 connector
10uF
C63
R91
R93
Matched Net Lengths [Tolerance = 100mil]
50
50
Diff Pair 100ohm
i
21
TXP
20
TXN
23
RXP
i
22
RXN
i
Diff Pair 100ohm
i Diff Pair 100ohm
3
LED1_LINK/ACT_GREEN
LED1/nINT/nPME/REGOFF
2 Diff Pair 100ohm
LED2/nINT/nPME/nINTSEL
LED2_SPEED_YELLOW
24 R84
RBIAS
3V3
12K1
9
VDDIO
19
L2
VDD1A
1
VDD2A
BLM18PG121SN1D
6
VDDCR
R90
50
3V3
Electrical schematics
UM1907
Figure 29. Ethernet PHY with RJ45 connector
1
10K_1%_0402
R4
4
OSC_24M
100nF
GND
2
3
NZ2520SB-24.00M
EN
OUT
OSC_24M
DCMI_SDA
DCMI_SCL
DCMI_PWR_EN
DCMI_NRST
DCMI_PIXCK
DCMI_HSYNC
DCMI_VSYNC
DCMI_D[0..7]
VDD
X1
DCMI_SDA
DCMI_SCL
DCMI_PWR_EN
DCMI_NRST
C3
3V3
DCMI_D[0..7]
DCMI_PIXCK
DCMI_HSYNC
DCMI_VSYNC
DCMI_SDA
3V3
DocID027942 Rev 2
3V3
C1
10uF
C2
100nF
DCMI_PWR_EN
DCMI_NRST
100_1%_0402
Camera_CLK
DCMI_VSYNC
100_1%_0402
R2
100_1%_0402
R3
DCMI_SCL R1
OSC_24M
DCMI_HSYNC
DCMI_PIXCK
DCMI_D0
DCMI_D1
DCMI_D2
DCMI_D3
DCMI_D4
DCMI_D5
DCMI_D6
DCMI_D7
FPU330ZH-BT1D3-CA
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
P1
Reference: MB1191
Date: 10/16/2015
Size: A4
Project: STM32F746G-DISCO
Title: External Camera connector
Revision: B-04
Sheet: 12 of 13
UM1907
Electrical schematics
Figure 30. External camera connector
37/49
48
38/49
L4
3V3
VL
DocID027942 Rev 2
LCD_SCL
LCD_SDA
LCD_INT
LCD_RST
LCD_DE
LCD_DISP
LCD_CLK
LCD_HSYNC
LCD_VSYNC
LCD_BL_CTRL
LCD_G[0..7]
LCD_B[0..7]
LCD_R[0..7]
10nF
C96
BLVDD
4.7uF_16V
C97
LCD_BL_CTRL
LCD_SCL
LCD_SDA
LCD_INT
LCD_RST
LCD_DE
LCD_DISP
LCD_CLK
LCD_HSYNC
LCD_VSYNC
LCD_BL_CTRL
LCD_G[0..7]
LCD_B[0..7]
LCD_R[0..7]
100nF
C95
FCM1608KF-601T03BLGND
L5
FCM1608KF-601T03
BLVDD
BLVDD
0
R81
4K7
R85
8
1
7
3
9
BLGND
4.7uH 1A 30%
L3
STPS1L40M
STLD40DPUR
SW
Vo
Vi
NC
EN
GND
FB
PGND Rset
U10
D5
4
2
6
5
VH
10nF
C65
R75
10_1%_0805
BLGND
R82
100K
BLGND
C64
4.7uF_50V
Default I2C Address : 01110000
R74
100nF
C53
3V3
4K7
C49
4.7uF
LCD_INT
LCD_SCL
LCD_SDA
LCD_RST
LCD_BL_A
LCD_BL_K
LCD_DE
LCD_DISP
RK043FN48H-CT672B
GND
GND
GND
GND
VDD
INT
SCL
SDA
RESET
VBL+
VBL-
DE
DISP
CLK
HSYNC
VSYNC
U19
B0
B1
B2
B3
B4
B5
B6
B7
G0
G1
G2
G3
G4
G5
G6
G7
R0
R1
R2
R3
R4
R5
R6
R7
21
22
23
24
25
26
27
28
13
14
15
16
17
18
19
20
5
6
7
8
9
10
11
12
Backlight driver & PFC of LCD panel
3
29
35
36
4
38
39
40
37
2
1
34
31
30
LCD_CLK
LCD_HSYNC 32
LCD_VSYNC 33
Reference: MB1191
Date: 10/16/2015
Size: A4
Project: STM32F746G-DISCO
Title: LCD 4.3" with Capacitive Touch
LCD_B0
LCD_B1
LCD_B2
LCD_B3
LCD_B4
LCD_B5
LCD_B6
LCD_B7
LCD_G0
LCD_G1
LCD_G2
LCD_G3
LCD_G4
LCD_G5
LCD_G6
LCD_G7
LCD_R0
LCD_R1
LCD_R2
LCD_R3
LCD_R4
LCD_R5
LCD_R6
LCD_R7
Revision: B-04
Sheet: 13 of 13
Electrical schematics
UM1907
Figure 31. 4.3-inch LCD with capacitive touch
UM1907
STM32F746G-DISCO IO Assignment
Appendix A
STM32F746G-DISCO IO Assignment
Table 10. STM32F746G-DISCO IO assignment
Pin No.
Pin Name
Signal or Label
Comment
A1
PE4
LTDC_B0
-
A2
PE3
OTG_HS_OverCurrent
-
A3
PE2
QUADSPI_BK1_IO2
-
A4
PG14
ETH_TXD1
-
A5
PE1
FMC_NBL1
-
A6
PE0
FMC_NBL0
-
A7
PB8
ARDUINO SCL/D15
-
A8
PB5
USB_OTG_HS_ULPI_D7
-
A9
PB4
ARDUINO PWM/D3
-
A10
PB3
SYS_JTDO-SWO
-
A11
PD7
SPDIF_RX0
-
A12
PC12
SDMMC_CK
-
A13
PA15
ARDUINO PWM/D9
-
A14
PA14
SYS_JTCK-SWCLK
-
A15
PA13
SYS_JTMS-SWDIO
-
B1
PE5
DCMI_D6
-
B2
PE6
DCMI_D7
-
B3
PG13
ETH_TXD0
-
B4
PB9
ARDUINO SDA/D14
-
B5
PB7
VCP_RX
-
B6
PB6
QUADSPI_BK1_NCS
-
B7
PG15
FMC_SDNCAS
-
B8
PG11
ETH_TX_EN
-
B9
PJ13
LTDC_B1
-
B10
PJ12
OTG_FS_VBUS
(1)
B11
PD6
Audio_INT
-
B12
PD0
FMC_D2_DA2
-
B13
PC11
SDMMC_D3
-
B14
PC10
SDMMC_D2
-
B15
PA12
USB_OTG_FS_DP
-
C1
VBAT
-
Connected to VDD
C2
PI8
NC1
-
DocID027942 Rev 2
39/49
48
STM32F746G-DISCO IO Assignment
UM1907
Table 10. STM32F746G-DISCO IO assignment (continued)
40/49
Pin No.
Pin Name
Signal or Label
Comment
C3
PI4
SAI2_MCLK_A
-
C4
PK7
LTDC_DE
-
C5
PK6
LTDC_B7
-
C6
PK5
LTDC_B6
-
C7
PG12
LTDC_B4
-
C8
PG10
SAI2_SD_B
-
C9
PJ14
LTDC_B2
-
C10
PD5
OTG_FS_PowerSwitchOn
-
C11
PD3
DCMI_D5
-
C12
PD1
FMC_D3_DA3
-
C13
PI3
ARDUINO D7
-
C14
PI2
ARDUINO D8
-
C15
PA11
USB_OTG_FS_DM
-
D1
PC13
uSD_Detect
-
D2
PF0
FMC_A0
-
D3
PI5
SAI2_SCK_A
-
D4
PI7
SAI2_FS_A
-
D5
PI10
LTDC_HSYNC
-
D6
PI6
SAI2_SD_A
-
D7
PK4
LTDC_B5
-
D8
PK3
LCD_BL_CTRL
-
D9
PG9
DCMI_VSYNC
-
D10
PJ15
LTDC_B3
-
D11
PD4
OTG_FS_OverCurrent
-
D12
PD2
SDMMC_CMD
-
D13
PH15
TP3
-
D14
PI1
ARDUINO SCK/D13
-
D15
PA10
USB_OTG_FS_ID
-
E1
PC14/OSC32_IN
RCC_OSC32_IN
-
E2
PF1
FMC_A1
-
E3
PI12
LCD_DISP
-
E4
PI9
LTDC_VSYNC
-
E5
PDR_ON
-
Connected to PU R38
E6
BOOT0
-
Connected to PD R45
E7
VDD
-
-
DocID027942 Rev 2
UM1907
STM32F746G-DISCO IO Assignment
Table 10. STM32F746G-DISCO IO assignment (continued)
Pin No.
Pin Name
Signal or Label
Comment
E8
VDD
-
-
E9
VDD
-
-
E10
VDD
-
-
E11
VCAP_2
-
Connected to C48
E12
PH13
DCMI_PWR_EN
-
E13
PH14
DCMI_D4
-
E14
PI0
ARDUINO PWM/CS/D10
-
E15
PA9
VCP_TX
(1)
F1
PC15/OSC32_OUT
RCC_OSC32_OUT
-
F2
VSS
-
-
F3
PI11
B_USER
-
F4
VDD
-
-
F5
VDD
-
-
F6
VSS
-
-
F7
VSS
-
-
F8
VSS
-
-
F9
VSS
-
-
F10
VSS
-
-
F11
VDD
-
-
F12
PK1
LTDC_G6
-
F13
PK2
LTDC_G7
-
F14
PC9
SDMMC_D1
-
F15
PA8
ARDUINO PWM/D5
-
G1
PH0/OSC_IN
RCC_OSC_IN
-
G2
PF2
FMC_A2
-
G3
PI13
LCD_INT
-
G4
PI15
LTDC_R0
-
G5
VDD
-
-
G6
VSS
-
-
G10
VSS
-
-
G11
VDDUSB
-
Connected to VDD
G12
PJ11
LTDC_G4
-
G13
PK0
LTDC_G5
-
G14
PC8
SDMMC_D0
-
G15
PC7
ARDUINO RX/D0
-
DocID027942 Rev 2
41/49
48
STM32F746G-DISCO IO Assignment
UM1907
Table 10. STM32F746G-DISCO IO assignment (continued)
42/49
Pin No.
Pin Name
Signal or Label
Comment
H1
PH1/OSC_OUT
RCC_OSC_OUT
-
H2
PF3
FMC_A3
-
H3
PI14
LTDC_CLK
-
H4
PH4
USB_OTG_HS_ULPI_NXT
-
H5
VDD
-
-
H6
VSS
-
-
H10
VSS
-
-
H11
VDD
-
-
H12
PJ8
LTDC_G1
-
H13
PJ10
LTDC_G3
-
H14
PG8
FMC_SDCLK
-
H15
PC6
ARDUINO TX/D1
-
J1
NRST
-
Hardware RESET
J2
PF4
FMC_A4
-
J3
PH5
FMC_SDNWE
-
J4
PH3
FMC_SDNE0
-
J5
VDD
-
-
J6
VSS
-
-
J10
VSS
-
-
J11
VDD
-
-
J12
PJ7
LTDC_G0
-
J13
PJ9
LTDC_G2
-
J14
PG7
ARDUINO D4
-
J15
PG6
ARDUINO D2
-
K1
PF7
ARDUINO A4
-
K2
PF6
ARDUINO A5
-
K3
PF5
FMC_A5
-
K4
PH2
NC2
-
K5
VDD
-
-
K6
VSS
-
-
K7
VSS
-
-
K8
VSS
-
-
K9
VSS
-
-
K10
VSS
-
-
K11
VDD
-
-
DocID027942 Rev 2
UM1907
STM32F746G-DISCO IO Assignment
Table 10. STM32F746G-DISCO IO assignment (continued)
Pin No.
Pin Name
Signal or Label
Comment
K12
PJ6
LTDC_R7
-
K13
PD15
FMC_D1_DA1
-
K14
PB13
USB_OTG_HS_ULPI_D6
-
K15
PD10
FMC_D15_DA15
-
L1
PF10
ARDUINO A1
-
L2
PF9
ARDUINO A2
-
L3
PF8
ARDUINO A3
-
L4
PC3
FMC_SDCKE0
-
L5
BYPASS_REG
-
Connected to PD R20
L6
VSS
-
-
L7
VDD
-
-
L8
VDD
-
-
L9
VDD
-
-
L10
VDD
-
-
L11
VCAP_1
-
Connected to C47
L12
PD14
FMC_D0_DA0
-
L13
PB12
USB_OTG_HS_ULPI_D5
-
L14
PD9
FMC_D14_DA14
-
L15
PD8
FMC_D13_DA13
-
M1
VSSA
-
Connected to GND
M2
PC0
USB_OTG_HS_ULPI_STP
-
M3
PC1
ETH_MDC
-
M4
PC2
USB_OTG_HS_ULPI_DIR
-
M5
PB2/BOOT1
QUADSPI_CLK
-
M6
PF12
FMC_A6
-
M7
PG1
FMC_A11
-
M8
PF15
FMC_A9
-
M9
PJ4
LTDC_R5
-
M10
PD12
QUADSPI_BK1_IO1
-
M11
PD13
QUADSPI_BK1_IO3
-
M12
PG3
EXT_RST
-
M13
PG2
RMII_RXER
-
M14
PJ5
LTDC_R6
-
M15
PH12
DCMI_D3
-
N1
VREF-
-
Connected to GND
DocID027942 Rev 2
43/49
48
STM32F746G-DISCO IO Assignment
UM1907
Table 10. STM32F746G-DISCO IO assignment (continued)
44/49
Pin No.
Pin Name
Signal or Label
Comment
N2
PA1
ETH_REF_CLK
-
N3
PA0/WKUP
ARDUINO A0
-
N4
PA4
DCMI_HSYNC
-
N5
PC4
ETH_RXD0
-
N6
PF13
FMC_A7
-
N7
PG0
FMC_A10
-
N8
PJ3
LTDC_R4
-
N9
PE8
FMC_D5_DA5
-
N10
PD11
QUADSPI_BK1_IO0
-
N11
PG5
FMC_A15_BA1
-
N12
PG4
FMC_A14_BA0
-
N13
PH7
I2C3_SCL
-
N14
PH9
DCMI_D0
-
N15
PH11
DCMI_D2
-
P1
VREF+
-
Connected to VDDA
P2
PA2
ETH_MDIO
-
P3
PA6
DCMI_PIXCK
-
P4
PA5
USB_OTG_HS_ULPI_CK
-
P5
PC5
ETH_RXD1
-
P6
PF14
FMC_A8
-
P7
PJ2
LTDC_R3
-
P8
PF11
FMC_SDNRAS
-
P9
PE9
FMC_D6_DA6
-
P10
PE11
FMC_D8_DA8
-
P11
PE14
FMC_D11_DA11
-
P12
PB10
USB_OTG_HS_ULPI_D3
-
P13
PH6
ARDUINO PWM/D6
-
P14
PH8
I2C3_SDA
-
P15
PH10
DCMI_D1
-
R1
VDDA
-
Connected to VREF+
R2
PA3
USB_OTG_HS_ULPI_D0
-
R3
PA7
ETH_CRS_DV
-
R4
PB1
USB_OTG_HS_ULPI_D2
-
R5
PB0
USB_OTG_HS_ULPI_D1
-
R6
PJ0
LTDC_R1
-
DocID027942 Rev 2
UM1907
STM32F746G-DISCO IO Assignment
Table 10. STM32F746G-DISCO IO assignment (continued)
Pin No.
Pin Name
Signal or Label
Comment
R7
PJ1
LTDC_R2
-
R8
PE7
FMC_D4_DA4
-
R9
PE10
FMC_D7_DA7
-
1. By default OTG_FS_VBUS is driven by software and not by the alternate function of the STM32F746NGH6
(R64 = ON, R63 = OFF, R58 = ON and PA9 = VCP_TX (Virtual Com Port) and PJ12 = OTG_FS_VBUS).
To use the alternate function OTG_FS_VBUS of the STM32F746NGH6, it's needed to have: R64 = OFF,
R63 = ON, R58 = OFF. In that configuration, VCP_TX is no longer available and PA9 = OTG_FS_VBUS,
PJ12 = not connected.
DocID027942 Rev 2
45/49
48
Mechanical drawing
Appendix B
UM1907
Mechanical drawing
Figure 32. Mechanical drawing
46/49
DocID027942 Rev 2
UM1907
Federal Communications Commission (FCC) and Industry Canada (IC) Compliance
Appendix C
Federal Communications Commission (FCC)
and
Industry Canada (IC) Compliance
C.1
FCC Compliance Statement
C.1.1
Part 15.19
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
C.1.2
Part 15.105
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
C.1.3
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and the receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help..
Part 15.21
Any changes or modifications to this equipment not expressly approved by
STMicroelectronics may cause harmful interference and void the user’s authority to operate
this equipment.
C.2
IC Compliance Statement
C.2.1
Compliance Statement
Industry Canada ICES-003 Compliance Label: CAN ICES-3 (B)/NMB-3(B)
C.2.2
Déclaration de conformité
Étiquette de conformité à la NMB-003 d’Industrie Canada: CAN ICES-3 (B)/NMB-3(B)
DocID027942 Rev 2
47/49
48
Revision history
UM1907
Revision history
Table 11. Document revision history
Date
Revision
12-Jun-2015
1
Initial release.
2
Updated cover page adding mbed-enabled logo.
Added:
- Section 1: Features
- Section 2: Demonstration software
- Section 3: Product marking
- Section 4: Ordering information
- Section 5: Technology partners
- Section Appendix C: Federal Communications Commission
(FCC) and Industry Canada (IC) Compliance
Updated Section 8: Electrical schematics figure 19 until the
figure 31.
Updated Section 6.2: Power supply.
Updated Section 6.1.1: Drivers.
02-Nov-2015
48/49
Changes
DocID027942 Rev 2
UM1907
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2015 STMicroelectronics – All rights reserved
DocID027942 Rev 2
49/49
49
">