Heat & Glo Twilight II ModernTwilight-II-MDC Owner's Manual

Owner’s Manual

Care and Operation

INSTALLER: Leave this manual with party responsible for use and operation.

OWNER: Retain this manual for future reference.

Contact your dealer with questions regarding installation, operation or service.

NOTICE: DO NOT discard this manual!

Model:

TWILIGHT-II-MDC

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death, or property damage.

• DO NOT store or use gasoline or other flam mable vapors and liquids in the vicinity of this or any other appliance.

• What to do if you smell gas

- DO NOT try to light any appliance.

- DO NOT touch any electrical switch. DO

NOT use any phone in your building.

- Leave the building immediately.

- Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

- If you cannot reach your gas supplier, call the fire department.

• Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

DANGER

HOT GLASS WILL

This appliance may be installed as an OEM installation in manufactured home (USA only) or mobile home and must be installed in accordance with the manufacturer’s instructions and the Manufactured Home

Construction and Safety Standard, Title 24

CFR, Part 3280 in the United States , or the

Standard for Installation in Mobile Homes,

CAN/CSA Z240 MH Series, in Canada.

This appliance is only for use with the type(s) of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certified kit is used.

individuals.

DO NOT TOUCH

NEVER

GLASS

ALLOW CHILDREN

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed for the protection of children and other at-risk

In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fitter.

See appliance installation manual for additional

Commonwealth of Massachusetts requirements.

Outdoor Lifestyles by Hearth & Home Technologies • Twilight-II-MDC Owner’s Manual • 2369-971 Rev. N • 1/20 1

2

1

Welcome

Read this manual before operating this appliance.

Please retain this Owner’s Manual for future reference.

Read the Installation Manual before making any installation or finishing changes.

A. Congratulations

Congratulations on selecting an Outdoor LifeStyles gas fireplace, an elegant and clean alternative to wood burning fireplaces. The Outdoor LifeStyles gas fireplace you have selected is designed to provide the utmost in safety, reliability, and efficiency.

As the owner of a new fireplace, you’ll want to read and carefully follow all of the instructions contained in this owner’s manual. Pay special attention to all cautions and warnings.

This owner’s manual should be retained for future reference. We suggest that you keep it with your other important documents and product manuals.

The information contained in this owner’s manual, unless noted otherwise, applies to all models and gas control systems.

Your new Outdoor LifeStyles gas fireplace will give you years of durable use and trouble-free enjoyment. Welcome to the Hearth & Home Technologies family of fireplace products!

Local Dealer Information

DEALER: Fill in your name, address, phone and email information here and appliance information below.

Dealer Name: ________________________________________________________

Address: ____________________________________________________________

____________________________________________________________

Phone: _____________________________________________________________

Email: _____________________________________________________________

Appliance Information:

Brand: ________________________________________________ Model Name: ___________________________

Serial Number: __________________________________________ Date Installed: __________________________

Listing Label Information/Location

The model information regarding your specific fireplace can be found on the rating plate usually located in the control area of the fireplace.

Type of Gas

Gas and Electric

Information

Outdoor Lifestyles, a brand of Hearth & Home Technologies

7571 215th Street West, Lakeville, MN 55044

((

Not

Ne use with doit pas entre fuel.

utilise avec solide).

Type of Gas (Sorte Gaz) ::

N TURAL GAS

This in appliance must the USA installed in

CAN/CGA B149 codes. with local

(Installer ou, en l’absence de reglements, selon codes, if if not, selon les follow ANSI les codes codes d’installation ou reglements

CAN/CGA-B149.)

ANSI Z21XX-XXXX · · CSA

Minimum Permissible Gas for Purposes Adjustment.

Approved Minimum (De Acceptable

Maximum Pressure (Pression)

0.0 in

0.0 in w.c.

w.c.

(Po.

(Po. d’eau) d’eau)

Maximum Manifold Pressure (Pression) 0.0 in w.c.

(Po. d’eau)

Minimum Manifold Pressure (Pression) 0.0 in w.c.

(Po. d’eau)

Total Electrical Requirements: 000Vac, 00Hz., than 00 Amperes

MADE IN USA

ALTITUDE:

MAX. BTUH:

MIN. INPUT BTUH:

ORIFICE SIZE:

Model:

(Modele):

Serial

(Serie):

Model Number

Serial Number

Outdoor Lifestyles by Hearth & Home Technologies • Twilight-II-MDC Owner’s Manual • 2369-971 Rev. N • 1/20

Safety Alert Key:

• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.

• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.

• CAUTION!

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• NOTICE: Used to address practices not related to personal injury.

Table of Contents

1 Welcome

A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

B. Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2 Product Specific Information

A. Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

B. Glass Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

C. Thermal Performance Data . . . . . . . . . . . . . . . . . . . . . . . . 6

D. Air Infiltration, Water Resistance and Structural Tests . . . 6

E. BTU Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3 Important Safety and Operating Information

A. Appliance Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

B. General Operating Parts . . . . . . . . . . . . . . . . . . . . . . . . . . 8

C. Fuel Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

D. Good Faith Wall Surface/TV Guidelines . . . . . . . . . . . . . . 8

E. Before Lighting Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . 10

F. Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . . 11

G. Appliance Break-In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

H. Heat Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

I. Detailed Component Operating Instructions . . . . . . . . . . 12

4 Maintenance and Service

A. Maintenance: Frequency and Tasks . . . . . . . . . . . . . . . . 13

B. Maintenance Tasks: Homeowner . . . . . . . . . . . . . . . . . . 13

C. Maintenance Tasks: Qualified Service Technician . . . . . 16

5 Troubleshooting and Frequently Asked Questions

A. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 17

B. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

6 Reference Materials



A. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

B. Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

C. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

 = Contains updated information.


4

B. Limited Warranty

Outdoor Lifestyles by Hearth & Home T echnologies™

Limited Lifetime Warranty

Hearth & Home Technologies (“HHT”) extends the following warranty for all Outdoor Lifestyles by HHT™ brand products (“Products”) that are purchased from an HHT authorized dealer.

WARRANTY COVERAGE:

HHT warrants to the original owner of the Product at the site of installation, and to any transferee taking ownership of the Product at the site of installation within one year following the date of original purchase, that the Product will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered components manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period, HHT will, at its option, repair or replace the covered components. This warranty is subject to conditions, exclusions and limitations as described below.

WARRANTY PERIOD:

The warranty period begins on the earlier of: (i) the date of invoice for the Product;

(ii) in the case of new home construction, the date of first occupancy of the residence or six months after the date of sale of the Product by an HHT authorized dealer, whichever occurs first; or (iii) the date 24 months following the date of Product shipment from HHT, regardless of the invoice or occupancy date.

WARRANTY CONDITIONS:

• The Limited Lifetime Warranty covers Products that are purchased through a HHT authorized dealer or distributor. A list of HHT authorized dealers is available on the HHT branded websites.

• This warranty is only valid while the Product remains at the site of original installation.

• Contact your installing dealer for warranty service. If the installing dealer is unable to provide necessary parts, contact the nearest HHT authorized dealer. Additional service fees may apply if you are seeking warranty service from a dealer other than the dealer from whom you originally purchased the Product.

• Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping charges for parts are not covered by this warranty.

• The Product body, metal firebox and heat exchanger carry the Limited Lifetime Warranty from the date of installation.

• The following components do not carry the Limited Lifetime Warranty but are warranted as follows: o One Year from Date of Installation:

▪ Gas and Electrical Components or Gaskets

▪ Nickel Plated Materials

• Excludes tarnishing

▪ Glass Breakage, Logs/Refractory/Glass Panels due to thermal breakage

• Surface, hairline cracks, scratches and slight color changes are not covered

▪ Venting, optional accessories, optional glass doors

▪ Labor Associated with Warranty Service Work

WARRANTY EXCLUSIONS:

This warranty does not cover the following:

• Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and exterior surface finishes may occur; this is not a flaw and not covered under warranty.

• Damage to printed, plated, or enameled surfaces caused by fingerprints, accidents, misuse, scratches, melted items, or other external sources and residues left on surfaces from the use of abrasive cleaners or polishes.

• Repair or replacement of parts that are subject to normal wear and tear during the warranty period. These parts include: paint, firebricks, grates, flame guides and the discoloration of glass.

• Minor expansion, contraction, or movement of certain parts causing noise. These conditions are normal and complaints related to this noise are not covered by this warranty.

Outdoor Lifestyles Warranty - 2108-975C – 6/5/2019 - 1


B. Limited Warranty (continued)

• Damages resulting from: (1) failure to install, operate, or maintain the Product in accordance with the installation instructions, operating instructions, and listing agent identification label furnished with the Product; (2) failure to install the Product in accordance with local building codes; (3) shipping or improper handling; (4) improper operation, abuse, misuse, continued operation with damaged, corroded or failed components, accident, or incorrectly performed repairs; (5) inad- equate ventilation, negative pressure or environmental conditions, including, without limitation: hail, snow, ice, fallen branches, flooding, water damage and fading of color; (6) use of fuels other than those specified in the operating instructions; (7) installation or use of components not supplied with the Product or any other components not expressly authorized and approved by

HHT; (8) modification of the Product not expressly authorized and approved by HHT in writing; and/or (9) interruptions or fluctuations of electrical power supply to the Product.

• Non-HHT venting components, hearth components or other accessories used in conjunction with the Product.

• Any part of a pre-existing fireplace system in which an insert or a decorative gas appliance is installed.

• The Product ’ s capability to heat the desired space. Information is provided to assist the consumer and the dealer in selecting the proper appliance for the application. Consideration must be given to the Product ’ s location and configuration and environmental conditions.

This warranty is void if:

• The Product has been over-fired or operated in atmospheres contaminated by chlorine, fluorine, or other damaging chemicals. Over-firing can be identified by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling, cracking and discoloration of steel or enamel finishes and cracking or spalling of refractory or cementitious materials.

• The Product is subjected to prolonged periods of dampness, condensation, ice or snow.

• There is any damage to the Product or other components due to water or weather damage which is the result of, but not limited to, improper chimney or venting installation.

LIMITATIONS OF LIABILITY:

Repair or replacement in accordance with the provisions of this warranty will be the owner ’ s exclusive remedy for and will constitute HHT ’ s sole obligation under this warranty, under any other warranty

(express or implied), or in contract, tort or otherwise; provided, however, that if HHT is unable to provide repair or replacement in an expedient and cost effective manner, HHT may discharge all such obligations by refunding the purchase price of the Product. No employee, agent, dealer, or other person is authorized to give any warranty on behalf of HHT. TO THE EXTENT ALLOWED BY LAW, HHT MAKES NO OTHER

WARRANTY, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE. HHT WILL NOT BE LIABLE FOR ANY CONSEQUENTIAL

OR INCIDENTAL DAMAGES ARISING OUT OF DEFECTS IN OR USE OF THE PRODUCTS. Some states do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you. This warranty gives you specific rights; you also may have other rights, which vary from state to state. The duration of any implied warranty is limited to the duration of the warranty period specified herein.

Outdoor Lifestyles Warranty - 2108-975C – 6/5/2019 - 2


2

Product Specific Information

A. Appliance Certification C. Thermal Performance Data

Sound Transmission

Class (STC)

Model: TWILIGHT-II-MDC

Thermal Resistance

(R Value)

Thermal Conductivity

(K Value)

27 0.8hr-sq ft-ºF/BTU 1.25 BTU-in/hr-sq ft-ºF

MODEL: TWILIGHT-II-MDC

LABORATORY: Underwriters Laboratories, Inc. (UL)

TYPE: Direct Vent Gas Appliance

STANDARD: ANSI Z21.50-2016 • CSA2.22-2016

This product is listed to ANSI standards for “Vented Gas

Fireplaces” and applicable sections of “Gas Burning

Heating Appliances for Manufactured Homes and Recreational Vehicles”, and “Gas Fired Appliances for Use at

High Altitudes”.

NOTICE: This installation must conform with local codes.

In the absence of local codes you must comply with the

National Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A. and the CAN/CGA B149 Installation Codes in

Canada.

NOT INTENDED FOR USE AS A HEAT SOURCE.

This appliance is decorative in nature and not intended to be a source of heat.

NOT FOR USE WITH SOLID FUEL.

This appliance is not intended to burn solid fuel.

D. Air Infiltration, Water Resistance and

Structural Tests

T

he Hearth & Home Technologies TWILIGHT-II-MDC Indoor/Outdoor Appliance unit was tested to the following

ASTM standards at the Stork Twin City Testing labora tory.

Air infiltration test ASTM:E283-(04) . The sample was tested at 1.57 psf (equivalent to a 25-mph windload). Water resistance test ASTM:E331-00 . The test specimen was tested at the requested test pressures of 8.0 & 25.0 psf.

Structural test ASTM:E330-02 . The unit was tested to a design pressure of 50-psf, a test pressure of 75-psf.

Test Results

Model

TWILIGHT-II-

MDC

Indoor/Outdoor

Air Infiltration

(ASTM E283)

0.07CFM/ft2

Water Resistance

(ASTM E331)

No leakage

@ 8psf & 25psf

Structural Load

(ASTM E330)

No Blowout

@ 75psf

6

B. Glass Specifications

Tempered Glass (Interior Glass)

Hearth & Home Technologies appliances manufactured with tempered glass may be installed in hazardous locations such as bathtub enclosures as defined by the

Consumer Product Safety Commission (CPSC). The tempered glass has been tested and certified to the re quirements of ANSI Z97.1

and CPSC 16 CFR 1202

(Safety Glazing Certification Council SGCC# 1595 and

1597 . Architectural Testing, Inc. Reports 02-31919.01

and 02-31917.01

).

This statement is in compliance with CPSC 16 CFR Section 1201.5 “Certification and labeling requirements” which refers to 15 U.S. Code (USC) 2063 stating “…Such certificate shall accompany the product or shall otherwise be furnished to any distributor or retailer to whom the product is delivered.”

Some local building codes require the use of tempered glass with permanent marking in such locations. Glass meeting this requirement is available from the factory.

Please contact your dealer or distributor to order.

Ceramic Glass (Exterior Glass)

This appliance is equipped with 5 mm ceramic glass. Replace glass only with 5 mm ceramic glass. Please contact your dealer for replacement glass.

E. BTU Specifications

Model

U.S. (0-2000 FT) or

Canada (2000-4500 FT)

TWILIGHT-II-MDC

(NG)

TWILIGHT-II-MDC

(Propane)

US

CAN

US

CAN

Input

BTU/h

38,000

34,200

36,000

33,300


Orifice Size

(DMS)

32

33

50

51

3

Important Safety and Operating Information

A. Appliance Safety

• Never leave children alone near a hot fireplace, whether operating or cooling down.

WARNING! DO NOT operate fireplace before reading and understanding operating instructions. Failure to operate fireplace according to operating instructions could cause fire or injury.

• Teach children to NEVER touch the fireplace.

• Consider not using the fireplace when children will be present.

DANGER

HOT GLASS WILL

Contact your dealer for more information, or visit: www.

hpba.org/Product-Info/Fireplace-Stove-Heater/Glass-

Fronts-Safety.

To prevent unintended operation when not using your fire place for an extended period of time (summer months, vacations, trips, etc):

DO NOT TOUCH GLASS

• Remove batteries from remote controls.

• Turn off wall controls.

NEVER ALLOW CHILDREN

• Unplug 3 volt adapter plug (IPI) and remove batteries on

IPI models.

• Keep children away.

• CAREFULLY SUPERVISE children in same room as fireplace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

• Clothing, furniture, draperies, and other flammable materials must not be placed on or near the appliance.

WARNING: This product and the fuels used to operate this product (liquid propane or natural gas), and the products of combustion of such fuels, can expose you to chemicals including benzene, which is known to the State of California to cause cancer and reproductive harm. For more information go to: www.

P65Warnings.ca.gov.

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed for the protection of children and other at-risk individuals. DO NOT operate the appliance with the barrier removed. If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier for this appliance.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

Clear Space

WARNING! DO NOT place combustible objects in front of the fireplace or block louvers.

High temperatures may start a fire. See Figure 3.1.

Avoid placing candles and other heat-sensitive objects on mantel or hearth. Heat may damage these objects.

NOTE: INTERIOR VIEW

Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children and others may be susceptible to accidental contact burns.

• A physical barrier is recommended if there are at risk individuals in the house.

• To restrict access to a fireplace or stove, install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the room and away from hot surfaces.

• Install a switch lock or a wall/remote control with child protection lockout feature.

• Keep remote controls out of reach of children.

3 FT

PLACE

Figure 3.1 Clear Space


B. General Operating Parts

Figure 3.2 references the general operating parts of the appliance and the section of this manual in which they are discussed.

D. Good Faith Wall Surface/TV Guidelines

Figure 3.3 references the maximum interior wall surface temperatures above the appliance.

NOTE: INTERIOR VIEW

DECORATIVE DOORS

(NOT SHOWN)

SECTION 6.A

FIXED GLASS ASSEMBLY

(NOT SHOWN)

SECTION 4.B

MANTEL

FAN KIT

SECTION 6.A

CLEAR SPACE

SECTION 3.A

HEARTH EXTENSION

(not required)

Interior or Exterior

Figure 3.2 General Operating Parts

C. Fuel Specifications

WARNING! Risk of Fire or Explosion! Appliance must be set up for compatible gas type!

• This appliance is designed to operate on either natural gas or propane. Make sure the appliance is compatible with gas type selected for installation site.

• Conversions must be made by a qualified service technician using Hearth & Home Technologies specified and approved parts.

FIREPLACE

OPENING

TO CEILING

120°F

130°F

180°F

150°F

140°F

160°F

24 in.

30 in.

48 in.

42 in.

36 in.

200°F

12 in.

18 in.

6 in.

MEASUREMENTS FROM

TOP EDGE OF THE OPENING

APPLIANCE FRONT

Figure 3.3 Maximum Interior Wall Surface Temperatures Above

Appliance

NOTICE: Temperatures listed above are taken with a temperature measuring probe as prescribed by the test standard used for appliance certification. Temperatures on walls or mantels taken with an infrared thermometer may yield increased temperatures of up to 30 degrees or more depending on the thermometer settings and material characteristics being measured.

8 Outdoor Lifestyles by Hearth & Home Technologies • Twilight-II-MDC Owner’s Manual • 2369-971 Rev. N • 1/20

TV Wall

Bracket

Good Faith Guidelines for TV Installa ons above a Typical Gas Fireplace

TV on the wall

TV

TV recessed into the wall

A

Item Minimum Dimensions

A 2.5 inches

B

2 inches minimum to 3 inches maximum

C 18 inches

D

Wall Brkt + TV Thickness + 2.5 inches

B

Mantel

D C A C

B

Fireplace Fireplace

Notes:

1. These are good faith recommended clearances only and not a guarantee of compliance with all TV manufacturers’ maximum allowable opera ng temperatures.

2. Since every home has unique air fl ow characteris cs and maximum allowable opera ng temperatures can vary from manufacturer to manufacturer and from model to model, actual TV temperatures should be validated at the me of each installa on. TVs should not be used in situa ons where the actual TV temperature exceeds the manufacturers’ maximum allowable opera ng temperatures iden fi ed in the

TV’s technical speci fi ca ons. Contact the TV’s manufacturer directly if you cannot locate this informa on or have ques ons regarding the informa on.

3. Mantel height and depth must conform to mantle requirements speciﬁ ed in the fi replace installa on manual.

4.

“C” dimension taken from the top of the hood or ﬁrepl ace opening.

5.

Sugges ons on how to further reduce TV temperatures: a. Increase “A” dimension.

b.

Increase “C” dimension, however, increasing “B” dimension beyond maximum recommended typically results in higher temperatures.

Figure 3.4 Good Faith TV Guidelines - Interior Side of Appliance


E. Before Lighting Fireplace

Before operating this fireplace for the first time, have a qualified service technician :

• Verify all shipping materials have been removed from inside and/or underneath the firebox.

• Review proper placement of logs, ember material and/ or other decorative materials.

• Check the wiring.

• Check the air shutter adjustment.

• Ensure that there are no gas leaks.

• Ensure that the glass is sealed and in the proper position and that the integral barrier is in place.

WARNING! Risk of Fire or Asphyxiation! DO NOT operate fireplace with fixed glass assembly removed.


F. Lighting Instructions (IPI)

The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer. To prolong battery life, remove them when using the transformer.

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING

A. This appliance is equipped with an intermittent pilot ignition (IPI) device which automatically lights the burner. DO NOT try to light the burner by hand.

B.

BEFORE LIGHTING , smell all around the appliance area for gas. Be sure to smell •

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, DO NOT WHAT TO DO IF YOU SMELL GAS

• DO NOT try to light any appliance.

D.

DO NOT use this appliance if any part has been under water. Immediately call

• DO NOT touch any electric switch; do not use any phone in your building.

the control system and any gas control which has been under water.

LIGHTING INSTRUCTIONS (IPI)

1. This appliance is equipped with an ignition device which automatically lights the burner. DO NOT try to light the burner by hand.

2.

top of this label. If you do not smell gas, go to next step.

GAS

VALVE

3. To light the burner:

Equipped with wall switch: Turn ON/OFF switch to ON.

Equipped with remote or wall control: Press ON or FLAME button.

Equipped with thermostat: Set temperature to desired setting.

4. If the appliance does not light after three tries, call your service technician or gas supplier.

TO TURN OFF GAS TO APPLIANCE

1. Equipped with wall switch: Turn ON/OFF switch to OFF.

Equipped with remote or wall control: Press OFF button.

Equipped with thermostat: Set temperature to lowest setting.

2. Service technician should turn off electric power to the control when performing service.

DANGER

HOT GLASS WILL CAUSE BURNS.

DO NOT TOUCH GLASS UNTIL COOLED.

NEVER ALLOW CHILDREN TO TOUCH GLASS.

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed for the protection of children and other at-risk individuals.

WARNING:

DO NOT CONNECT LINE VOLTAGE (110/120 VAC OR 220/240 VAC) TO THE CON-

TROL VALVE.

CAUTION:

Hot while in operation. DO NOT touch. Keep children, clothing, furniture, gasoline

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this ap-

DO NOT operate the appliance with broken. Replacement of the

removed, cracked or

should be done by a licensed or agency or the gas supplier.

This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.

NOT FOR USE WITH SOLID FUEL

For use with natural gas and propane. A conversion kit, as supplied by the manufacturer, shall be used to convert this appliance to the alternate fuel.

WARNING: This product and the fuels used to operate this product (liquid propane or natural gas), and the products of combustion of such fuels, can expose you to chemicals including benzene, which is known to the State of California to cause cancer and reproductive harm. For more information go to: www.

P65Warnings.ca.gov.

This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSIZ223.1/ NFPA 54, or the National Gas and

Propane Installation code, CSA B149.1.

For additional information on operating your

Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.

refer to www.hearthnhome.com.


G. Appliance Break-In

Initial Break-in Procedure

• The fireplace should be run three to four hours continuously on high.

• Turn the fireplace off and allow it to completely cool.

• Remove fixed glass assembly. See Section 5.A.

• Clean fixed glass assembly. See Section 4.

• Replace the fixed glass assembly and run continuously on high an additional 12 hours.

This cures the materials used to manufacture the fire place.

NOTICE! Open windows for air circulation during fire place break-in.

• Some people may be sensitive to smoke and odors.

• Smoke detectors may activate.

H. Heat Management

Burn Rate

The TWILIGHT-II-MDC has a constant burn rate which is controlled by the gas valve. Therefore the flame height is not adjustable.

I. Detailed Component Operating

Instructions

IntelliFire™ Ignition System

IntelliFire™, an ignition system exclusively featured in

Heatilator, Heat & Glo & Quadra-Fire products, is an energy-saving pilot ignition system for gas fireplaces and inserts. It provides an ignition flame only when needed and has a battery backup system that supplies power to spark the ignition flame in the event of a power outage.

Intellifire ™ is an intermittent pilot ignition, which is an electronic system. The term Intermittent is used because the pilot burner flame is only present when the main burner is operating. When the main burner is off the pilot is also off.

NOTICE: Batteries should not be placed in the battery pack while using the transformer. Remove batteries before using the transformer, and unplug the transformer before installing the batteries. Battery polarity must be correct or module damage will occur.

Appliance ON/OFF:

If an optional remote control or wall control is installed, it should be used to control the ON/OFF function of the appliance. Follow instructions included with the installed control.

To operate the appliance without a wall control or remote control, use the ON/OFF switch located inside the control cavity of the appliance. See Figure 3.5.

Access to the ON/OFF switch may vary depending on the choice of decorative front. In some cases a louver may need to be opened. In other cases, the decorative front may need to be removed.

CAUTION! Risk of Electric Shock! Avoid touching wires and electrical components in appliance control cavity.

12

ON/OFF

SWITCH

Figure 3.5. ON/OFF Switch Location


4

Maintenance and Service

Any safety screen or guard removed for servicing must be replaced prior to operating the fireplace.

When properly maintained, your fireplace will give you many years of trouble-free service. Contact your dealer to answer questions regarding proper operation, troubleshooting and service for your appliance. Visit www.

heatnglo.com to locate a dealer. We recommend annual service by a qualified service technician.

A. Maintenance: Frequency and Tasks

The matrix below is an overview of maintenance tasks to be performed on the appliance. Sections B and C give details and instructions needed to assist the appropriate person in performing the tasks.

Task

Glass Cleaning

Doors/Fronts/

Surrounds

Remote Control

Exhaust

Termination

Drip Tray

Frequency

Seasonally

Annually

Seasonally

Seasonally

As Needed

To be completed by

Homeowner

Gasket Seal and Glass

Inspection

Firebox

Inspection

Control

Compartment &

Firebox Top

Glass Rock

Media

Burner Ignition

& Operation

Annually

Annually

Annually

Annually

Annually

Qualified Service

Technician

B. Maintenance Tasks: Homeowner

Installation and repair should be done by a qualified service technician only. The fireplace should be inspected before use and at least annually by a professional service person.

The following tasks may be performed annually by the homeowner. If you are uncomfortable performing any of the listed tasks, please call your dealer for a service ap pointment.

More frequent cleaning may be required due to lint from carpeting or other factors. Control compartment, burner and circulating air passageway of the fireplace must be kept clean.

CAUTION! Risk of Burns! The fireplace should be turned off and cooled before servicing.

Note: If the appliance is installed on a screened porch, ensure the screen is kept clean to maintain proper airflow.

Glass Cleaning

Frequency: Seasonally

By: Homeowner

Tools Needed : Protective gloves, glass cleaner, drop cloth and a stable work surface.

CAUTION! Handle fixed glass assembly with care.

Glass is breakable.

• Avoid striking, scratching or slamming glass

• Avoid abrasive cleaners

• DO NOT clean glass while it is hot

• Prepare a work area large enough to accommodate fixed glass assembly and door frame by placing a drop cloth on a flat, stable surface.

Note : Fixed glass assembly and gasketing may have res idue that can stain carpeting or floor surfaces.

• Remove door or decorative front from fireplace and set aside on work surface.

WARNING! Risk of Asphyxiation! Handle fixed glass assembly with care. Inspect the gasket to ensure it is undamaged and inspect the glass for cracks, chips or scratches.

• DO NOT operate fireplace with glass removed, cracked, broken or scratched.

• Replace as a complete assembly.

• Remove fixed glass assembly from appliance. See instructions below for removing and replacing interior and exterior glass assemblies.

• Clean glass with a non-abrasive commercially available cleaner.

- Light deposits: Use a soft cloth with soap and water

- Heavy deposits: Use commercial fireplace glass cleaner (consult with your dealer)

• Carefully set fixed glass assembly in place on fireplace.

Hold glass in place with one hand and secure glass latches with the other hand.

• Inspect and operate all glass latches to ensure they move freely and no obstructions are present.

• Reinstall door or decorative front.

Removing Fixed Glass Assembly- Interior

• Loosen two wing nuts on bottom glass retainer bracket.

• Loosen and remove two wing nuts on top glass retainer bracket. Remove glass retainer bracket. See Figure 4.1

• Lift glass assembly off of glass retainer bracket.

Replacing Fixed Glass Assembly - Interior

• Position glass assembly on bottom glass retainer bracket.

Tighten wing nuts on bottom glass retainer bracket.

• Position top of glass assembly, position top glass retainer bracket and secure with two wing nuts.


WING NUT LOCATIONS

GLASS RETAINER

GLASS LATCHES

4.1 Glass Assembly - Interior Side

GLASS RETAINER BRACKET

4.3 Glass Latch Locations - Exterior Side

Removing Fixed Glass Assembly- Exterior

• Remove vanity panel from appliance to expose glass latches.

• Pull glass latch out to release. Grasp glass assembly on sides and pull bottom toward you. Slide glass assembly down and out from under glass retainer.

GLASS LATCH

WING NUT ON THREADED STUD

4.2 Glass Assembly Detail - Interior Side

14

4.4 Glass Latch Detail - Exterior Side

Replacing Fixed Glass Assembly - Exterior

• Slide top of glass assembly into position under glass retainer. Position bottom of glass assembly and secure latches.

• Replace vanity panel.


Doors, Surrounds, Fronts

Frequency: Annually

By: Homeowner

Tools needed : Protective gloves, stable work surface

• Assess condition of screen and replace as necessary.

• Inspect for scratches, dents or other damage and repair as necessary.

• Check that louvers are not blocked.

• Vacuum and dust surfaces.

Remote Control


By: Homeowner

Tools needed: Replacement batteries and remote control instructions.

• Locate remote control transmitter and receiver.

• Verify operation of remote. Refer to remote control operation instructions for proper calibration and setup procedure.

• Place batteries as needed in remote transmitters and battery-powered receivers.

• Place remote control out of reach of children.

If not using your fireplace for an extended period of time

(summer months, vacations/trips, etc), to prevent unintended operation:

• Remove batteries from remote controls.

• Unplug 3 volt adapter plug on IPI models.

Exhaust Termination


By: Homeowner

Tools needed: Protective gloves and safety glasses.

• Inspect exhaust termination for blockage or obstruction such as plants, bird nests, leaves, snow, debris, etc.

• Verify exhaust termination clearance to subsequent construction (building additions, decks, fences, or sheds).

See Section 6.

Drip Tray

Frequency: As Needed

By: Homeowner

Tools needed : Protective gloves

Under certain weather conditions, some water may accumulate inside the appliance. This is normal and expected. The control compartment contains two removable drip pans that may be cleaned as necessary.

• Note orientation of drip trays on shoulder screw before removing. Replace drip trays in same orientation as shown in Figure 4.5.

• Excess moisture can be eliminated by burning the appliance for a few hours.

LEFT

SIDE

RIGHT

SIDE

CORRECT INSTALLATION

Figure 4.5 Drip Tray

NOTE ORIENTATION

OF DRIP TRAYS ON

SHOULDER SCREW

LEFT

SIDE

RIGHT

SIDE

INCORRECT INSTALLATION


C. Maintenance Tasks: Qualified Service

Technician

The following tasks must be performed by a qualified ser vice technician.

Gasket Seal and Glass Assembly Inspection

Frequency: Annually

By: Qualified Service Technician

Tools needed: Protective gloves, drop cloth and a stable work surface.

• Inspect gasket seal and its condition.

• Inspect fixed glass assembly for scratches and nicks that can lead to breakage when exposed to heat.

• Confirm there is no damage to glass or glass frame.

Replace as necessary.

• Verify that fixed glass assembly is properly retained and attachment components are intact and not damaged.

Replace as necessary.

Firebox

Frequency: Annually


Tools needed: Protective gloves, sandpaper, steel wool, cloths, mineral spirits, primer and touch-up paint.

• Inspect for paint condition, warped surfaces, corrosion or perforation. Sand and repaint as necessary.

• Replace fireplace if firebox has been perforated.

Control Compartment and Firebox Top

Frequency: Annually


Tools needed: Protective gloves, vacuum cleaner, dust cloths

• Vacuum and wipe out dust, cobwebs, debris or pet hair.

Use caution when cleaning these areas. Screw tips that have penetrated the sheet metal are sharp and should be avoided.

• Remove all foreign objects.

• Verify unobstructed air circulation.

soap. Rinse thoroughly with clean water. Drain water from container and allow the glass rock media to dry thoroughly before installing into the fireplace. Reinstall glass rock media into appliance using the instructions in the appliance installation manual.

Burner Ignition and Operation

Frequency: Annually


Tools needed: Protective gloves, vacuum cleaner, whisk broom, flashlight, voltmeter, indexed drill bit set, and a manometer.

• Verify burner is properly secured and aligned with pilot or igniter.

• Clean off burner top, inspect for plugged ports, corrosion or deterioration. Replace burner if necessary.

• Verify batteries have been removed from battery back-up

IPI systems to prevent premature battery failure or leaking.

• Check for smooth lighting and ignition carryover to all ports. Verify that there is no ignition delay. Inspect and ensure the lighting of the main burner occurs within four seconds of the main gas valve opening.

• Inspect for lifting or other flame problems.

• Verify air shutter setting is correct. See Installation

Manual for required air shutter setting. Verify air shutter is clear of dust and debris.

• Inspect orifice for soot, dirt and corrosion. Verify orifice size is correct. See Service Parts List for proper orifice sizing.

• Verify manifold and inlet pressures. Adjust regulator as required.

• Inspect pilot flame pattern and strength. See Figure 4.1 for proper pilot flame pattern. Clean or replace orifice spud as necessary.

• Inspect IPI flame sensing rod for soot, corrosion and deterioration. Polish with fine steel wool or replace as required.

• Verify that there is not a short in flame sense circuit by checking continuity between pilot hood and flame sense rod. Replace pilot as necessary.

• Check all accessible gas-carrying tubes, connections, pipes and other components for leaks.

Glass Rock Media Maintenance

Frequency: Annually


Tools needed: Protective gloves, container, mild dish soap, cloth or rag

• The glass rock media will loose its luster over time. This is normal wear for this application. The appearance of the media can be restored by periodic cleaning. It is recommended that the glass rock media be rinsed thoroughly with water to remove dust and debris. An easy method to clean the glass rock media is to place the contents of the bag into a container of water and mild dish

16

Figure 4.1 IPI Pilot Flame Pattern


5

Troubleshooting and Frequently Asked Questions

A. Frequently Asked Questions

ISSUE

Condensation on the glass

Blue flames

Odor from fireplace

Film on the glass

Metallic noise

Glass Rock Media Kit

SOLUTIONS

This is a result of gas combustion and temperature variations. As the fireplace warms, this condensation will disappear.

This is a result of normal operation and the flames will begin to yellow as the fireplace is al lowed to burn for 20 to 40 minutes.

When first operated, this fireplace may release an odor for the first several hours. This is caused by the curing of materials from manufacturing. Odor may also be released from finish ing materials and adhesives used near the fireplace. These circumstances may require ad ditional curing related to the installation environment.

This is a normal result of the curing process of the paint. Glass should be cleaned within 3 to

4 hours of initial burning. A non-abrasive cleaner such as gas appliance glass cleaner may be necessary. See your dealer.

Noise is caused by metal expanding and contracting as it heats up and cools down, similar to the sound produced by a furnace or heating duct. This noise does not affect the operation or longevity of the fireplace.

There may be some “cracking” noise coming from the fireplace during the first few heating and cooling cycles. This noise is associated with settling rock and some minor cracking of larger pieces of rock. This will lessen over time as the glass rock is conditioned to the heat ing and cooling temperature changes.

It is expected that a few small pieces (approximately 10 pieces) of rock may fall through the base pan and come to rest on the fireplace bottom. This has no affect on fireplace perfor mance.

Glass Rock Media Color Change

It is normal for the glass rock media to change color slightly over the lifetime of the appliance.

Is it normal to see the pilot flame burn continually?

In an intermittent pilot ignition system (IPI), the pilot flame should turn off when appliance is turned off. Some optional control systems available with IPI models may allow pilot flame to remain lit.

Contact your dealer for additional information regarding operation and troubleshooting. Visit www.hearthnhome.com to locate a dealer.


B. Troubleshooting

With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a qualified service technician in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician. Contact your dealer to arrange a service call by a qualified service technician.

Symptom

3. Pilot sparks, but

Pilot will not light.

Possible Cause

1. Pilot won’t light.

The ignitor/module makes noise, but no spark.

A. Incorrect wiring.

B. Loose connections or electrical shorts in the wiring.

C. Ignitor gap is too large.

D. Module.

2. Pilot won’t light, there is no noise or spark.

A. No power or transformer installed incorrectly.

B. A shorted or loose connection in wiring configuration or wiring har ness.

C. Improper wall switch wiring.

D. Module not grounded.

E. Module.

A. Gas supply.

Corrective Action

Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor are connected to correct terminals on module and pilot assembly.

Verify no loose connections or electrical shorts in wiring from module to pilot assembly. Verify connections underneath pilot assembly are tight; also verify connections are not grounding out to metal chassis, pilot burner, pilot enclosure, mesh screen if present, or any other metal object.

Verify gap of igniter to right side of pilot hood. The gap should be approximately .095 in. (2.41 mm) to .135 in. (3.43 mm).

Turn ON/OFF rocker switch or wall switch to OFF position. Remove ignitor wire “I” from module. Place a grounded wire about 3/16 in. (5 mm) away from “I” terminal on module. Place ON/OFF rocker switch or wall switch in ON position. If there is no spark at “I” terminal module must be replaced. If there is a spark at “I” terminal, module is fine.

Inspect pilot assembly for shorted sparker wire or cracked insulator around electrode. Replace pilot if necessary.

Verify that transformer is installed and plugged into module. Check voltage of transformer under load at spade connection on module with ON/OFF switch in ON position. Acceptable readings of a good transformer are between 3.2 and 2.8 volts AC.

Remove and reinstall the wiring harness that plugs into module.

Verify there is a tight fit. Verify pilot assembly wiring to module. Re move and verify continuity of each wire in wiring harness. Replace any damaged components.

Verify that 110-120 VAC power is “ON” to junction box.

Verify black ground wire from module wire harness is grounded to metal chassis of appliance.

Turn ON/OFF rocker switch or wall switch to OFF position. Remove ignitor wire “I” from module. Place ON/OFF rocker switch or wall switch in ON position. If there is no spark at “I” terminal module must be replaced. If there is a spark at “I” terminal, module is fine.

Inspect pilot assembly for shorted sparker wire or cracked insulator around electrode.

Verify that incoming gas line ball valve is “open”. Verify that inlet pressure reading is within acceptable limits.

B. Ignitor gap is too large.

C. Module is not grounded.

D. Module voltage output / Valve/Pilot solenoid ohms readings.

Verify gap of igniter to right side of pilot hood. The gap should be approximately .095 in. (2.41 mm) to .135 in. (3.43 mm).

Verify module is securely grounded to metal chassis of appliance.

Verify battery voltage is at least 2.7 volts. Replace batteries if voltage is below 2.7.


Troubleshooting - (continued)

Symptom

4. Pilot lights but continues to spark, and main burner will not ignite.

(If the pilot continues to spark after the pilot flame has been lit, flame rectification has not occurred.)

Possible Cause Corrective Action

A. A shorted or loose connection in flame sensing rod.

Verify all connections to wiring diagram in manual. Verify connections underneath pilot assembly are tight. Verify connections are not grounding out to metal chassis, pilot burner, pilot enclosure or screen if present, or any other metal object.

B. Poor flame rectification or contaminated flame sensing rod.

With fixed glass assembly in place, verify that flame is en gulfing flame sensing rod on left side of pilot hood. Flame sensing rod should glow shortly after ignition. Verify correct pilot orifice is installed and gas inlet is set to pressure specifications. Polish flame sensing rod with fine steel wool to remove any contaminants that may have accumulated on flame sensing rod.

C. Module is not grounded.

D. Damaged pilot assembly or contaminated flame sensing rod.

E. Module.

Verify module is securely grounded to metal chassis of appliance. Verify that wire harness is firmly connected to the module.

Verify that ceramic insulator around the flame sensing rod is not cracked, damaged, or loose. Verify connection from flame sensing rod to white sensor wire. Polish flame sens ing rod with fine steel wool to remove any contaminants that may have accumulated on flame sensing rod. Verify continuity with a multimeter with ohms set at lowest range.

Replace pilot if any damage is detected.

Turn ON/OFF rocker switch or wall switch to OFF position.

Remove ignitor wire “I” from module. Place ON/OFF rocker switch or wall switch in ON position. If there is no spark at “I” terminal module must be replaced. If there is a spark at “I” terminal, module is fine.


6

Reference Materials

A. Accessories

Install approved accessories per instructions included with accessories. Contact your dealer for a list of approved accessories.

WARNING! Risk of Fire and Electric Shock! Use ONLY

Hearth & Home Technologies-approved optional accessories with this appliance. Using non-listed accessories could result in a safety hazard and will void the warranty.

Once installed, operate per instructions included with accessories.

Fan Kit (optional)

If desired, a fan kit may be added. Contact your dealer to order the correct fan kit.

Remote Controls, Wall Controls and Wall

Switches

Follow the instructions supplied with the control installed to operate your fireplace:

For safety:

• Install a switch lock or a wall/remote control with child protection lockout feature.

• Keep remote controls out of reach of children.

See your dealer if you have questions.

Decorative Doors and Fronts

WARNING! Risk of Fire! Install ONLY doors or fronts approved by Hearth & Home Technologies. Unapproved doors or fronts may cause fireplace to overheat.

This fireplace has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the fireplace with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

For more information refer to the instructions supplied with your decorative door or front.


36” Indoor/Outdoor

See-thru Gas Fireplace

TWILIGHT-II-MDC

Beginning Manufacturing Date: Dec 2014

Ending Manufacturing Date: Active

2

1

5

4

3

10 11

6

8 9

7

IMPORTANT: THIS IS DATED INFORMATION . Parts must be ordered from a dealer or distributor.

Hearth and Home Technologies does not sell directly to consumers . Provide model number and serial number when requesting service parts from your dealer or distributor.

ITEM

1

DESCRIPTION

Mesh Assembly, Exterior

Mesh

Outdoor Glass Assembly 2

3

4

5

6

Pilot Shield

Burner Assembly

Firebox Bracket

Glass Clip

7

8

9

10

11

Indoor Glass Assembly

Drain Pan

Base Pan Assembly

Junction Box

Junction Box Shield

Additional service part numbers appear on following page.

COMMENTS

Qty 2 req

Qty 2 req

Qty 2 req

PART NUMBER

2368-030

2368-225

GLA-OUTDOOR2

2290-109

2290-007

2290-123

2087-121

GLA-6TROC

2087-118

2290-015

SRV4021-013

2087-149


Stocked in Depot

Y

Y

Y

1/20

21

Service Parts TWILIGHT-II-MDC



#12 Valve Assembly

12.3

12.4

12.6

12.5

12.1

12.2

12.16

12.15

12.14

12.13

12.7

12.12

12.8

12.9

12.11

12.10



COMMENTS ITEM

12.1

DESCRIPTION

Pilot Assembly NG

Pilot Assembly Propane

Pilot Tube

12.2

Flex Tube Assembly

12.3

Valve Plate Gasket

12.4

Valve L Bracket

12.5

Valve Bracket

12.6

Valve Assembly Bracket

12.7

Flex Ball Valve Assembly

12.8

ON/OFF Rocker Switch Assembly

12.9

Valve NG

Valve Propane

12.10

Wire Assembly

12.11

Control Module

12.12

Wall Switch Wire

12.13

Battery Pack

12.14

Power Supply

12.15

Jumper Wire

12.16

3-Hole Grommet

Burner Orifice (NG) (#32C)

Burner Orifice (Propane) (#50C)

Additional service part numbers appear on following page.


PART NUMBER

SRV2090-012

2090-013

SRV485-301

4021-428

2087-112

674-168

2087-117

2087-116

SRV302-320

060-521A

593-500

RV593-501

SRV593-590

593-592

SRV2118-170

SRV593-594

SRV593-593

2155-033

SRV2118-420

SRV582-832

582-850


Y

Y

Y

Y

Y

Y

Y

Y

Y

Y

Y

Y

Y

Y

Y

Service Parts TWILIGHT-II-MDC





ITEM DESCRIPTION

Black Rock, 5 Lb Bag

Glass Latch Assembly

Non-Combustible Boards (set only)

Refractory Assembly

Top Panel Inside

COMMENTS

Qty 4 req

Qty 2 req

Touch Up Paint

Exterior

Interior

Cover Panel

Deflector Panel

Flashing

Hood-Exterior Side

Wind Screen Assembly

Pre LC4673185

Post LC4673185

PART NUMBER

2188-850

2382-400

2108-030

SRV2290-070

2086-127

SRV2087-999-A12

TUP-GBK-12

2368-114

2086-136MBK

2087-159

2368-113

2368-004

2368-014


Y

Media

Media, Black Glass Rock

Media, Amber Glass Rock

21 LB Crystal Media Kit

MEDIA-BLACK-20

MEDIA-AMBER-20

MEDIA-CRYSTAL21

Conversion Kits

Conversion Kit NG

Conversion Kit Propane

Pilot Orifice NG

Pilot Orifice Propane

Regulator NG

Regulator Propane

NGK-TWI-MOD

LPK-TWI-MOD

SRV593-528

SRV593-527

SRVNGK-DXF

SRVLPK-DXF


Y

Y

Y

Y

Y

Y

23

C. Contact Information

Please contact your Hearth & Home Technologies dealer with any questions or concerns.

For the location of your nearest Hearth & Home Technologies dealer, please visit www.hearthnhome.com.

Hearth & Home Technologies

7571 215th St, Lakeville, MN 55044

- NOTES -

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

________________________________________________________________________________

• Important operating and maintenance instructions included.

NOTICE

DO NOT DISCARD THIS MANUAL

• Read, understand and follow these instructions for safe installation and operation.

• Leave this manual with party responsible for use and operation.

This product may be covered by one or more of the following patents: (United States) 5613487, 6006743, 6019099,

6053165, 6145502, 6374822, 6484712, 6601579, 6769426, 6863064, 7077122, 7074035, 7098269, 7258116, 7322819,

7470729, 7726300, 8147240, 9625149 or other U.S. and foreign patents pending.

2000-945D

24

Printed in U.S.A. - Copyright 2020


No results