User’s Guide printWiFi™

Portable Mobile Printing Controller

Index

Section Page

Features 3

What’s Included 3

Safety Information

Getting to Know printWiFi

4

5

Downloading printView App

Getting to Know printView App

Operational Instructions

Step 1: Select Document

6

7

10

11

Step 2: Connect Printer & Mobile Device

Step 3: Printing

14

17

Document Import Options 22

Settings 24

WiFi (SSID, Security, Password)

Admin Password

Software/Firmware Update

Reset to Factory Default Settings

26

27

28

30

Power Switch, Charging & LED Indicator

Alert Message User Actions

32

34

Specifications 35

Troubleshooting 36

Compliance with FCC Regulations

Warranty Information

37

42

2

Thank you for purchasing printWiFi Mobile Printing Controller

Features:

• Print to local USB printers

• No printer drivers to install

• User selects printer from multiple connected printers.

• Full printer feature functionality

• Rechargeable Li-ion battery with over 2 hours of printing

• LED Battery Indicator

• Easy USB Charging

What’s Included printWiFi

Controller printWiFi Charging Cable

USB A Connector

USB Micro

Connector

printWiFi Printer Cable

USB A Connector

USB B

Connector printWiFi Quick Start Guide printView™ Free Download iTunes App Store & Play Store

3

Important Safety Instructions

1. Water and Moisture - printWiFi should not be used near water. For example: near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement.

2. Objects and Liquid Entry - Care should be taken so that external objects do not fall into and liquids are not spilled onto any openings located on the product.

3. Heat - printWiFi should be situated away from heat sources such as radiators, heat registers, stoves or other appliances (including amplifiers) that produce heat.

4. Damage Requiring Service - printWiFi should be serviced by qualified service personnel when:

A. objects have fallen into or liquid has been spilled onto the enclosure.

B. printWiFi has been exposed to rain.

C. printWiFi has been dropped or the enclosure is damaged.

D. printWiFi exhibits a marked change in performance or does not operate normally.

5. Servicing - The user should not attempt to service printWiFi beyond those methods described in the user’s manual. Opening or removing covers will expose you to dangerous voltage and other hazards.

Service methods not covered in the user’s manual should be referred to qualified service personnel.

6. Safety Check - Upon completion of any service or repair to printWiFi, ask the service technician to perform safety checks to determine that the product is in proper working condition.

7. Battery - This device contains a rechargeable Lithium Polymer battery. Please do not attempt to replace the battery yourself. The battery may only be replaced by our authorized service centers.

4

Getting to Know printWiFi

Printer Controller™

Mobile Devices Connect via USB or WiFi

Printer Connects via USB Printer

Port using the supplied printWiFi

Printer Cable.

USB connection

Charges Mobile

Device when printWiFi is connected to

Mobile Device

AC Adapter

Charge printWiFi Battery via printWiFi Micro USB using

Mobile Device AC Adapter

Micro USB connection to Desktop or Laptop charges printWiFi

Battery and shares printer

Note: Charge printWiFi at least 4 hours before initial use

5

Power Switch & LED

Tri-Color LED displays battery charge level

• Green Full

• Amber < 50%

• Red < 10%

Press & Hold Power

Switch 10 Seconds for Reset

Getting to Know The printView App

printView App (IOS and Android devices)

The printWiFi is designed to work hand-in-hand with the feature rich printView app.

Download & Install

For iOS devices you will download the app from the App Store onto your device and for Android devices you will download the app from the Play Store onto your device. Your device must be connected to the

Internet to download the free printView app.

For iOS Devices (iPhone, iPad, iPod Touch, etc) use the

Apple App Store.

• Turn on your iPhone/iPad/iPod Touch and navigate to

the App Store.

• Tap the “Search” icon at the bottom of your screen and

search for “printView”.

• Open the printView app page and tap the “Free” button

in the upper right side of the screen.

• Tap “Install” and enter your App Store password to

begin download and installation.

For Android Device use the Play Store.

• Turn on your Android device and navigate to the Play Store.

• Tap the “Search” icon at the top of your screen and search

for “printView”.

• Open the printView app page and tap the “Free” button

in the upper right side of the screen.

• Tap “Install” and enter your Play Store password if prompted

to and begin download and installation.

6

Launch the App

Once the printView app is installed, navigate to the app on your device.

iPad

Android

printView familiar

App process

iPhone

7

Launch the App

continued

(Tablets)

Press Edit to remove Documents

Print & Open

In Buttons

iPad

Highlighting a Document from list on left

Opens it for Print

Previewing

Settings Accessed via Admin Button printWiFi Status Bar:

Displays Battery Level,

Charging & Status

Android is similar to an iPad with slight variations as shown below.

Press Delete to remove Documents

Android

printWiFi

Status Bar

Battery Display

Settings Accessed via Admin Button

8

Launch the App

continued

(Phones)

Opening a document in the printView App on a Android phone is similar to an iPhone. Smaller screen sizes on phones require the document list and the documents to be on seperate screens.

Press Edit to remove Documents

Highlighting a Document

Opens it for Print Previewing

iPhone

(Android Phone Similar)

printWiFi Status Bar:

Displays Battery Level,

Charging & Status

9

Operational Instructions

Printing with printWiFi - Simple Three Step Process:

1. Select: Document or Image - Open In the printView App

2. Connect: Mobile Device - printWiFi - Printer

3. Print: Print with full printer functionality

Step 1: Select - Document & Open in printView

Select and Open Document (example shows document being received via Email)

Open Document

iPad

Once Document is open. Use iOS

Open In function

Select printView to import document to printView App

Note: Additional Document Import Options defined on pages 21-23

10

Step 1: Select - Document & Open in printView

Select and Open Document (example shows document being received via Email)

iPhone

Opens Document

Once Document is open. Use iOS

Open In function

Select printView to import document to printView App

Note: Additional Document Import Option defined on pages 21-23

11

Step 1: Select - Document & Open in printView

Select and Open Document (example shows document being received via Email)

Android

Opens an email with attached document

Save document to

Android device storage

Open printView App and open document in printView

Note: Additional Document Import Options defined on pages 21-23

12

Step 1: Select - Document & Open in printView

Once printView App is open select desired document from the

Document List.

iPad

Android

Highlight and open document in printView App

iPhone

13

Step 2A: Connect – printWiFi to USB Printer

Connect printer to printWiFi using supplied USB printer cable.

Note: The LED will blink showing the printer is being installed. The first time each printer model is installed it will take 30 to 40 Seconds. The printWiFi keeps a list of most used printers and each subsequent time those printers are connected will take less than 10 seconds.

USB A Connector to printWiFi Printer Port printWiFi USB Printer

Cable (included)

USB B connector to connection located in rear of target printer

14

Step 2B: Connect Mobile Device to printWiFi

Mobile Device may be connected to printWiFi via a

Direct WiFi connection or

USB charging cable

Connect Phone or Tablet via WiFi

1. Power the printWiFi on.

2. Navigate to the WiFi menu on your mobile device.

3. Turn on WiFi and begin searching for available networks.

4. Select “printWiFi_XXXX” from the list of results, and your device

will begin to connect.

5. Close the Settings page and open the printView App. The status

bar on the bottom of the page will show WiFi connection status.

Phone/Tablet WiFi

Selection Settings

Default WiFi SSID is printWiFi_XXXX

XXXX is the last four digits of the MAC Address

iPad iPhone

Note: When using WiFi to connect to printWiFi the mobile device is not connected to the internet. To access the Internet disconnect from printWiFi and reconnect to a WiFi Hotspot or use Cellular.

15

Step 2B: Connect Mobile Device to printWiFi

Using

A USB Cable

Connect the mobile device to the printWiFi

Mobile USB Port using the Mobile

Device’s USB charging cable

13

16

Step 3: Print

Once the document is open, select “Print” in the upper right corner of the printView App (as shown on page 8). The Print Monitor Page will then appear, as shown below.

iPad iPhone

17

Android

Step 3A:

Select Printer Options

Printer Options page is displayed when an Automated Printer Match is made (if an automated Match is not made see 3C)

Select Desired Options

When completed press “Print”

Enter number of Copies & Pages or Page Range

Select Quality, Paper Tray & Type of Media

iPad

Android

To Print - Press “Print” at the bottom of the page

iPhone

18

Proceed to Step 3B Page 19

Step 3B:

Printing Status Page will display printing status

iPad iPhone

19

Android

Step 3C:

Manual Printer

Match:

In the event the

Automated Match is not made a

Manual Printer Setup is offered to the user.

iPad

From the drop down lists select the Manufacturer & Printer Model then press Continue.

Note: If there is not an exact model match choose one close

Android iPhone

If the 1st Manual Match selected doesn’t print correctly the process may be repeated by selecting the Manual Print process on the Print

Options Page.

Note: Access to change an existing Printer Description requires Admin

Password entry (default Admin Password is admin)

Then Repeat Steps 3A and 3B until a functioning Printer Description is identified or all potential Descriptions have been tried.

Note Supported Printers are listed on the PrintWiFi and PrintUSB Support

Website: http://www.imagetechcorp.com/support.html.

20

Document Import Options iPad and iPhone

printView allows importing of documents from the Camera Roll and

Cloud Storage locations such as: DropBox, One Drive and Google

Drive.

iPad

Press the “+” Button to access the Import

Document Page and select location of document storage.

iPhone

On iPad and iPhone documents can always be imported using the iOS

“Open In” function.

21

Document Import Options

continued

Camera Roll Example iPad

To select the Camera Roll scroll to the desired image and double click to import it into printView.

To select the Dropbox, Log In with your DropBox account and open list of DropBox files and double click on the file to import.

Dropbox Example

On iPad and iPhone documents can always be imported using iOS

“Open In” function.

22

Document Import Options

continued

printView allows importing of document from Camera Roll and Cloud

Storage locations such as: DropBox, One Drive and Google Drive.

Android

23

Settings

Password Access Screen:

The “Admin” button opens the Settings Password Access Screen. The default password is “admin”.

The “Admin” page provides WiFi Settings, Software/Firmware Updates and ability to reset the “Admin” password.

iPad

24

Android iPhone

Settings

A successful Log In provides access to the “Settings Page”

A USB connection is required for access to all settings as displayed below.

iPad

25

Android iPhone

WiFi Settings:

Allows configuration of Network Name (SSID),

Security, Password and Timeout Settings.

iPad

Android

26 iPhone

Reset Admin Password

To reset the “Admin” password, you must have your mobile device connected to the printWiFi via the USB charging cable. The default password is “admin”

iPad

Android

Android

27

Software/Firmware Update:

Your mobile device must be connected to the printWiFi via the USB charging cable and be connected to the internet via WiFi or Cellular.

The “Software/Firmware Update” button checks the existing firmware and will function only when an update is available.

iPad

28

Android iPhone

Software/Firmware Update:

continued

DO NOT POWER OFF OR DISCONNECT THE PRINTWIFI AND YOUR

MOBILE DEVICE DURING THE FIRMWARE UPDATE.

iPad

Software/Firmware Update:

continued

Upon completion a Success Page is displayed

iPad

29

Reset To Factory Default Settings

This is only available when a mobile device is connected to the printWi-

Fi via a USB Charging Cable.

Select “Edit” then the “Reset Settings” button appears.

Select Proceed

iPad iPhone

30

Reset To Factory Default Settings

continued

Upon Completion a Successful Completion Page is displayed.

iPad iPhone

31

printWiFi Power Switch:

The printWiFi power switch can be pressed for 1 second to turn the printWiFi on or off anytime except during the startup process. After pressing the Power Switch to turn on the printWiFi, it should be allowed to finish the 35 second startup process before attempting to press the power switch again. Interrupting the boot process can cause an abnormal state and should be avoided.

Reset the printWiFi by pressing the Power Switch for 10 seconds. A reset is not required during normal product operation. However, a Reset can be performed after a firmware upgrade or in the rare case of an abnormal state.

printWiFi Charging:

Connect the printWiFi Micro USB Cable to an USB AC Adapter. The printWiFi battery requires a minimum of 4 hours to charge with nothing else connected to it. A fully charged battery will provide approx. 1 hour of printing and retain the charge for up to 3 weeks in Power OFF mode.

Power save feature turns the unit off after 10 minutes of inactivity when running on battery.

Note: A mobile device may be charged when the printWiFi is charging by connecting the mobile device (phone or tablet) to the printWiFi

Mobile Device USB connector. When a mobile device is being charged through the printWiFi, a full charge time for both devices may require 12 hours or longer. Note: Tablet screens should be off to facilitate a faster charge.

32

printWiFi LED Indicators:

printWiFi uses the LED to display multiple functions including: Battery

Level, Startup Process Activity and Alerts.

Battery Level LED indications as table shows below:

Color

Green

Amber

Red

Charge

50% to 100%

10% to 50%

< 10%

Approx. Print Time

@ 100% - 1* Hours

@ 50% - 30* Minutes

@ 10% - 5* Minutes

Note*: Variations based on Mobile Devices using USB & WiFi vs. WiFi Only, age and charge level of battery.

Startup Process Indicators: The LED will blink for a portion of the 35 second startup process then turn a solid color based on the Battery Level.

Activity Indicator: LED also blinks during the printing process and initial connection of devices (phones, tablets and printers).

Error / Alert Indicator:

printWiFi uses the LED to display Battery, CPU Thermal Overload and USB Overload Alerts by generating a Flashing Red LED. An Alert message will be sent to the connected mobile device. See page 35 for details.

33

Troubleshooting

Symptom

No LED Indicators after pressing the power switch

LED lights up, then goes off

printWiFi Troubleshooting

Cause Corrective Action

Low Battery

Plug the Micro USB charging into the printWiFi and an AC adapter into a wall outlet. The printWiFi LED should turn

“Red”, indicating it is charging

Led lights up and printWiFi boots but cannot connect to the printView App

Low Battery

Low Battery

Low Battery

Low Battery

Low Battery

Low Battery

Low Battery

Low Battery

WiFi Not Connected

WiFi Not Connected

Poor USB Connection

Mobile Device /APP

Verify the wall outlet that the AC adapter is plugged into is not controlled by wall switch and if it is, confirm the wall switch is turned on

Check printWiFi charging cable with another Micro USB

Device to verify it is working

In case the problem still exists, see warranty information on page 25 to obtain service

Plug the Micro USB charging into the printWiFi and an AC adapter into a wall outlet. The printWiFi LED should turn

“Red”, indicating it is charging

Verify the wall outlet that the AC adapter is plugged into is not controlled by wall switch and if it is, confirm the wall switch is turned on

Check the printWiFi charging cable with another Micro USB

Device to verify it is working

Plug the Micro USB charging into the printWiFi and an AC adapter into a wall outlet. Press and Hold the power switch for 10 seconds to “Reset” the printWiFi

In case the problem still exists, see warranty information on page 25 to obtain service

Check Mobile device WiFi setting connected to printWiFi-XXXX

Verify Correct WiFi password is being used. If not known then connect mobile device via USB, go to printWiFi Admin

Settings on printWiFi to verify WiFi Password or reset.

App connects to printWiFi but cannot print

Can’t open document in printView App

Can’t Access

Admin Settings printWiFi Abnormal State

Printer Connection

Printer Not Ready printWiFi Abnormal State

Printer Not Compatible

Edit Document is selected

Incorrect Admin Password

Check USB Cable with another device

Close all Apps on mobile device and restart the App

Press and hold the power switch for 10 seconds to

“Reset” the printWiFi

Ensure that the USB cable is connected to printer and the printWiFi’s printer port

Verify that the printer is powered on, has paper and is ready to print

Press and hold the power switch for 10 seconds to

“Reset” the printWiFi

Verify that the printer is on printWiFi approved printer list

Press “Done” on the main page of the printView app to return to the”Document Available” state

If after all attempts to remember your password fails, use factory “Reset” function to “Reset” the “Admin” access password. The default “Admin” password is “admin”

34

Alert Message Requires User Action:

USB Overload Alert- (Message on App and LED Flashing Red)

1. Disconnect USB devices. Verify nothing is shorting the connector pins

on the printWiFi connector.

2. Check USB cable for damage and functionality with another computer.

3. Check another device with the cable and printWiFi.

4. If problem persists see warranty information on page 38 to

obtain service.

Battery Over Temp Alert-(Message on App and LED Flashing Red)

1. If charging, disconnect charging cable and turn off printWiFi allowing

battery and system to cool for 15 to 30 minutes.

2. If not charging, turn off and allow system to cool for 15 to 30 minutes.

3. Remove any attached USB devices before turning unit on.

4. Verify attached USB devices are functioning correctly as defined in

USB Overload Alert.

5. If problem persists see warranty information on page 38 to obtain service.

System Over Temp Alert-(Message on App and LED Flashing Red)

1. Follow Both USB and Battery Temp Alert Processes

2. If problem persists see warranty information on page 38 to

obtain service.

35

Specifications

Processor: Freescale ARM MCIMX28

Memory: 2GB Flash, 1GB RAM

Interfaces: 2 USB A Rev. 2.0, 1 Micro USB

WiFi: 802.11b/g/n

Battery: Lithium Ion 1500mAh

Dimensions: 4” x 2.2” x 0.85”

Weight: < 0.5lbs

Software Requirements

Operating Systems

• Apple iOS 7.0 or later

• Android OS 2.3X, 3.X, 4.X or higher

Supported File Formats

• Excel xls, xlsx, csv

• Word doc, docx

• PowerPoint ppt, pptx

• Document pdf, txt, html

• Image jpg, png, bmp, gif

36

Compliance with FCC Regulations

Contains

FCC ID: 2AAD5-PRINTWIFI1500

IC No.: 11687A-PRINTWIFI1

NOTICE

Federal Communication Interference Statement (United States only)

This equipment has been tested and found to comply with the limits for a class

B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Re-orient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment to an outlet on a circuit different from that to

which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.

37

FCC Rules, Part 15

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference, including interference that may

cause undesired operation of this device.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure

Guidelines in Supplement C to OET65 radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20 cm or more away from person’s body.

Canadian Department of Communications Industry Canada

Notice (Canada only)

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du

Canada.

Industry Canada

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference, including interference that may

cause undesired operation of this device.

38

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :

(1) l’appareil ne doit pas produire de brouillage, et

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le fonctionnement.

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure

Guidelines in RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20 cm or more away from person’s body.

Cet équipement est conforme aux limites d’exposition aux rayonnements

énoncées pour un environnement noncontrôlé et respecte les règles les radioélectriques (RF) de d’exposition aux fréquences radioélectriques (RF) CNR-

102 de l’IC. Cet équipement doitêtre installé et utilisé en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

39

Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal

(ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.

This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s’il fait partie du matériel de catégorie I) a été approuvé par Industrie Canada pour fonctionner avec les types d’antenne

énumérés ci-dessous et ayant un gain admissible maximal et l’impédance requise pour chaque type d’antenne. Les types d’antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitation de l’émetteur.

For product available in the USA/Canada market, only channels 1-11 can be operated. Selection of other channels is not possible.

40

Antenna: Proprietary

Antenna gain information: Embedded Antenna: 4.0dBi (2.4 GHz)

Frequency Tolerance: +/-20ppm

WARNING:

The FCC / The Industry Canada regulations provide that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

THE SPECIFICATION AND EXTERNAL APPEARANCE OF THE printWiFi ARE

SUBJECT TO CHANGE WITHOUT PRIOR NOTICE.

41

Warranty Information

ImageTech (the Company) Limited Warranty

Any repair, replacement, or warranty service, and all questions about this product should be directed to the Company at www.myprintwifi.com. The

Company warrants to the original purchaser that the product will be free from defects in material, parts and workmanship for the period designated for this product. The warranty commences the day the product is purchased and covers up to a period of one (1) year. The Company agrees that it will, at its option, replace the defective product with either a new or remanufactured printWiFi equivalent to your original purchase during the warranty period.

Exclusions: This warranty does not apply to the appearance or exterior of the product which may have been damaged or defaced, altered or modified in design or construction. This warranty does not apply if the serial number is altered or removed, or if there is any damage due to power line surge, user damage to the AC power cord, connection to improper voltage source, general misuse, accidents, or repair attempts by unauthorized service agents. Other exclusions include rechargeable and non-rechargeable batteries. REPAIR OR

REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE

REMEDY OF THE CUSTOMER; THE COMPANY SHALL NOT BE LIABLE FOR

ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY

EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT, EXCEPT TO THE

EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF

MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE ON THIS

PRODUCT IS LIMITED TO THE DURATION OF THE WARRANTY.

42

Some states do not allow the exclusion or limitations of incidental or consequential damages, or limitations on how long the warranty lasts. In these cases the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

Obtaining Service: To obtain service, product literature, supplies or accessories visit our website, www.myprintwifi.com, to request a ticket for exchange/repair.

Please make sure to provide the date of purchase, model number and a brief description of the problem. Our customer service representative will contact you or send detailed return instructions.

The Company does not warrant that the printWiFi will work properly in all environmental conditions, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose other than the purpose identified within this user’s manual. The Company has made every effort to ensure that this user’s manual is accurate and disclaims liability for any inaccuracies or omissions that may have occurred. Information in this user’s manual is subject to change without notice and does not represent a commitment on the part of the

Company. The Company reserves the right to make improvements to this user’s manual and/or to the products described in this user’s manual at any time without notice. If you find information in this manual that is incorrect, misleading, or incomplete, please contact us through our website.

printWiFi-1-UG-RevE

43