advertisement
▼
Scroll to page 2
of 20
IS0504A User Manual Version: 2021/3/31 Contents SAFETY CAUTIONS------------------------------------------2 GROUNDING INSTRUCTIONS----------------------------3 ASSEMBLY INSTRUCTIONS------------------------------4 OPERATION GUIDE------------------------------------------7 EXPLODED DRAWING--------------------------------------11 PARTS LIST-----------------------------------------------------12 MAINTENANCE------------------------------------------------13 PRODUCT SPECIFICATION-------------------------------15 CONTACT US--------------------------------------------------16 Thank you for purchasing the IS0504A. Before operating this unit, please read this manual carefully to ensure optimum performance and safety. This manual should be kept available for future reference. REMARK: For product improvement, the company reserves the right to change the design and specification at any time without prior notice. Pictures are for reference use only and may differ from the actual product. Page 1 SAFETY CAUTIONS When using this product, basic precautions should always be followed, including the following: Please read the instruction carefully before starting to use this product. Danger – To reduce the risk of electric shock: 1. Always unplug this product from the electrical outlet immediately after using and before cleaning. Warning – To reduce the risk of burns, fire, electric shock, or physical injury: 1. The product should never be left unattended while plugged in. Unplug the product from the outlet when not in use. 2. Close supervision is necessary when this product is used by or near children, invalids, or disabled persons. 3. Be sure to use the product only for its intended use as described in this manual. Do not use any attachment not recommended by the manufacturer in order to avoid any danger or accidents. 4. Never operate the product if it has a damaged cord or plug, if it is not working properly, if it has been damaged, or dropped into water. Please return the product to the service center of seller for examination and repair. 5. Do not carry this product by the supply cord or use the cord as a handle. 6. 7. Keep the cord away from hot surfaces or ground. Never operate the product with the air vents blocked. Keep the air vents free of lint, hair, etc. 8. Never drop or insert any objects into any openings. 9. Do not use or operate outdoors. 10. Do not operate where aerosol (spray) products are being used or where oxygen is thin. 11. Before turning the product power off, turn all controls to the off position then remove the plug from the outlet. 12. Connect the product to a properly grounded outlet only. 13. If the treadmill is foldable, when user finishes using the treadmill, the elevation needs to be back to original position. 14. When user is using the treadmill, it can not be folded at the same time. 15. Keep a safety space of 2000mm x 1000mm away from the treadmill. 16. This machine is only intended for household use. 17. For the treadmill with folding function and electric elevation, be sure that the elevation is 0 before folding (To avoid interference of the components). 18. Stop using the treadmill if you feel faint, dizzy, or short of breath. 19. Wear appropriate exercise clothes when using the treadmill. Do not wear loose clothes that could become caught in the treadmill. Athletic support clothes are recommended for both men and women. Always wear athletic shoes. Never use the treadmill with bare feet, wearing only stockings, or in sandals. Page 2 GROUNDING INSTRUCTIONS The products must be grounded first. If malfunction or breakdown occurs, grounding will provide a path of least resistance for electric current to reduce the risk of electric shock. The product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Danger – Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the products are properly grounded. Do not modify the plug provided with the product – if it will not fit the outlet, have a proper outlet install by a qualified electrician. The products is for use on nominal 220-240 volt and has a grounding plug that looks like the plug illustrated in the figure . Make sure that the product is connected to an outlet having the same configuration as the plug. There is no need to use any adapter for this product. Figure Grounding methods GROUNDED OUTLET OUTLET GROUNDED PIN Page 3 ASSEMBLY INSTRUCTIONS OPEN THE BOX YOU CAN FIND THE ALL PARTS AS BELOW. Assembly Parts List: No. Desc. Spec. Qty No. Desc. Spec. Qty 1 Front base 1 13 Hexagon head Bolt M8*15 4 33 Upright-cover-Right 1 26 Lock Washer Φ8 6 34 Upright-cover-Left 1 21 Screw st4*12 2 72 Hexagon Wrench 5# 1 57 Emergency stop Key 1 73 Hexagon Wrench 6# 1 70 Silicon Oil 1 Cross open-end 74 Wrench 11 Hexagon head Bolt 13 14 15 M8*45 (thread 25) 1 6 Tool: 5#Wrench 5mm 1pcs ; 6#Wrench 6mm 1pcs ; Wrench 13、14、15 Attention: Note: do not plug in the power supply until the installation is complete. Page 4 1pcs STEP 1: 1. Open the packing carton, put the main frame on the level ground. STEP 2: 2.Use Wrench(72) to fasten Bolt(11), Washer(26) and Bolt(13) into uprights and base frame,but do not fix tightly first. ` STEP 3: 3. Use Wrench(72) to fasten Bolt(11), Washer(26) and Bolt(13) into uprights and base frame,but do not fix tightly first. STEP 4: 4.Secure the bolts tightly of STEP 1,2,3, then use Wrench(74) to fasten screw(21) into left base cover(33) and right base cover(34) firmly. Page 5 STEP 5:Folding machine 5.One hand hold the machine position A(see sketch of STEP 5), when you hear a sound from cylinder, then the machine is well installed. STEP 6: unfold the machine 6.One hand hold the machine position A(see sketch of STEP 6), use foot to press the cylinder(8), the machine declined to almost handrail height, release your hand, machine will go down smoothly. NOTE: For your safety and comfort, please check if all screws are fastened before your use! A brand new motorized treadmill has been successful assembled! Page 6 OPERATION GUIDE I﹕Button instruction: Function button: START, STOP, PROGRAM, MODE, SPEED+/-, Quick speed buttons. Function button instruction: A. “PROG.”button : When in STOP state,you can press “PROG.” button to select the preset program, U1-U5 program, and FAT. B. “MODE”button:to select TIME / DISTANCE / CALORIE countdown mode. C. “START”is the begin-running button. D. “STOP”is the stop-running button.When the machine is running,press this button first time,the machine will be paused,press again,the machine will be stopped. E. “SPEED+”and“SPEED -”to increase and decrease the speed, and also can adjust other parameters. F. “QUICK SPEED BUTTON”:Total 6 buttons,includes:2,4,6,8,10,12 km/h. II﹕Safety key function﹕ When the motor is working,take off the safety key,the console will stop,and no starting. III:Pulse function: When the machine is connected to power,both hands grasp the pulse sensors on the handrails.In order to receive accurate heartbeat value,please stand on the running platform,and grasp the pulse sensors no less than 30 seconds.Measure range:50—200 beats per minute. This data is for reference only and cannot be used for medical purpose. V:Numerical display range: Page 7 SET STARTING SETING RANGE VALUE BEGIN VALUE PROGRAM TIME(MIN:SEC.) 0:00 SPEED(KM/H) 0.0 DISTANCE(KM) CALORIE(KCAL) MODE TIME(MIN:SEC) 30:00 SHOWING RANGE 5:00-99:00 0:00-99:59 N/A 1.0-14.0 0.0-14.0 0.0 1.0 0.5-99.9 0.0-99.9 0 50 10-999 0-999 5:00-99:00 0:00-99:59 15:00 0:00 VI.PRESET PROGRAM CHART: The 40 preset programs: Each exercise program consists of 20 intervals.The running time of each interval of a program is equally distributed. TIME PROG Time set/20 intervals = running duration 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 P01 SPEED 2 3 3 4 5 3 4 5 5 3 4 5 4 4 4 2 3 3 5 3 P02 SPEED 2 4 4 5 6 4 6 6 6 4 5 6 4 4 4 2 2 5 4 2 P03 SPEED 2 4 4 6 6 4 7 7 7 4 7 7 4 4 4 2 4 5 3 2 P04 SPEED 3 5 5 6 7 7 5 7 7 8 8 5 9 5 5 6 6 4 4 3 P05 SPEED 2 4 4 5 6 7 7 5 6 7 8 8 5 4 3 3 6 5 4 2 P06 SPEED 2 4 4 4 5 6 8 8 6 7 8 8 6 4 4 2 5 4 3 2 P07 SPEED 2 3 3 3 4 5 3 4 5 3 4 5 3 3 3 6 6 5 3 3 P08 SPEED 2 3 3 6 7 7 4 6 7 4 6 7 4 4 4 2 3 4 4 2 P09 SPEED 2 4 4 7 7 4 7 8 4 8 9 9 4 4 4 5 6 3 3 2 P10 SPEED 2 4 5 6 7 5 4 6 8 8 6 6 5 4 4 2 4 4 3 3 P11 SPEED 2 5 8 10 7 7 10 10 7 7 10 10 5 5 9 9 5 5 4 3 P12 SPEED 3 4 9 9 5 9 5 8 5 9 7 5 5 7 9 9 5 7 6 3 P13 SPEED 3 6 7 5 9 9 7 5 5 7 9 5 8 5 9 5 9 9 4 3 P14 SPEED 2 2 4 5 6 5 4 3 2 1 2 3 4 5 6 5 4 3 2 1 P15 SPEED 2 4 6 8 6 6 4 4 2 2 2 4 6 8 6 6 4 4 2 2 P16 SPEED 2 4 6 8 10 8 6 4 2 2 2 4 6 8 6 6 4 4 2 2 P17 SPEED 2 2 6 6 8 10 6 6 2 2 2 2 6 6 8 10 6 6 2 2 P18 SPEED 2 3 4 5 2 3 4 5 3 2 2 3 4 5 2 3 4 5 3 2 P19 SPEED 2 4 6 2 4 6 2 4 6 2 2 4 6 2 4 6 2 4 6 2 P20 SPEED 1 3 4 5 6 5 4 3 2 1 1 3 4 5 6 5 4 3 2 1 P21 SPEED 4 5 4 4 4 2 3 3 5 3 2 3 3 4 5 3 4 5 5 3 P22 SPEED 5 6 4 4 4 2 2 5 4 2 2 4 4 5 6 4 6 6 6 4 P23 SPEED 2 4 4 4 4 2 4 5 3 2 2 4 4 6 6 4 7 7 7 4 P24 SPEED 3 5 9 5 5 6 6 4 4 3 3 5 5 6 7 7 5 7 7 8 P25 SPEED 3 4 5 4 3 3 6 5 4 2 2 4 4 5 6 7 7 5 6 7 P26 SPEED 1 3 6 4 4 2 5 4 3 2 2 4 4 4 5 6 8 8 6 7 P27 SPEED 4 5 3 3 3 6 6 5 3 3 2 3 3 3 4 5 3 4 5 3 Page 8 P28 SPEED 1 3 4 4 4 2 3 4 4 2 2 3 3 6 7 7 4 6 7 4 P29 SPEED 2 5 5 5 4 5 6 3 3 2 2 4 4 7 7 4 7 8 4 8 P30 SPEED 6 6 5 4 4 2 4 4 3 3 2 4 5 6 7 5 4 6 8 8 P31 SPEED 4 2 4 4 3 4 5 5 4 3 2 5 8 10 7 7 10 10 7 7 P32 SPEED 5 5 2 2 4 5 5 7 6 3 3 4 9 9 5 9 5 8 5 9 P33 SPEED 2 3 2 1 3 2 9 9 4 3 3 6 7 5 9 9 7 5 5 7 P34 SPEED 2 3 4 5 6 5 4 3 2 1 2 2 4 5 9 9 4 4 4 5 P35 SPEED 2 4 6 8 6 6 4 4 2 2 2 4 6 8 6 6 4 4 2 2 P36 SPEED 2 4 6 8 6 6 4 4 2 2 2 4 6 8 10 8 6 4 2 2 P37 SPEED 2 2 6 6 8 10 6 6 2 2 2 2 6 6 8 10 6 6 2 2 P38 SPEED 2 3 4 5 2 3 4 5 3 2 2 3 4 5 2 3 4 5 3 2 P39 SPEED 2 4 6 2 4 6 2 4 6 2 2 4 6 2 4 6 2 4 6 2 P40 SPEED 1 3 4 5 6 5 4 3 2 1 1 3 4 5 6 5 4 3 2 1 VII、CUSTOMIZED PROGRAMS OPERATION The user can set programs according to their own needs. There are 5 user-setting programs: U1, U2, U3, U4, U5. Each exercise program consists of 20 intervals. 1. Customized program setting: Press “PROG.” button in standby status to choose U1, U2, U3, U4, or U5, and the “TIME” window will flash to display the preset time. Press the SPEED+/- button to set the desired time, then press the “MODE” button to confirm and then you can set the program parameters, then set the first time interval, press the SPEED+/- button or Quick SPEED button to set the speed. Press the “MODE” button to complete the setting of the first time interval, and enter the setting of the second time interval to follow same operation, then follow same until all the 20 time intervals are set. After the setting is completed, the data will be saved permanently until the next time you reset it. This data will not be lost due to power outages. 2. Selection and startup of customized programs: Press the“PROG.” button in the standby status to choose a program among U1, U2, U3, U4, U5, and set the running time then you can press the “START” button to start running. VIII: Body fat test - FAT: Body mass index (FAT) is a measure of a person's height and weight, not the proportion of the body. FAT is suitable for any male and female, together with other health indicators to provide people with the basis for weight adjustment. 1: When the treadmill is stopped, press the program key to select the body fat test program and enter the body fat test. 2: Press the MODE button to set the gender, age, height and weight respectively. After setting, press the MODE button to test the result. At this time, please put your hands on the handrail sensors, and the body Fat value will be displayed within 8 seconds. Input parameter display and setting range: Parameter category Page 9 Default value Setting range Remark SEX(F1) 1(MAN) 1—2 AGE(F2) 25 years old 10—99 years HEIGHT(F3) 170 CM 100—200 CM WEIGHT(F4) 70KG 20—150KG RESULT(F5) 1=MAN 2=WOMAN AS BELOW Special note: This data is only used as a workout reference and cannot be used as medical data. Using Asian standards as a reference, fat test results: FAT ≤19 -Under weight 19<FAT ≤25 -Normal weight 25<FAT ≤29 -Over weight FAT≥30 -Obesity IX: Error message code meaning: Problem and Code Possible Cause Solution E1 Communication error A. Poor communication line contact Reconnect the communication line and check if the port is plugged in or replace the communication line. B. Defect console Replace the console C. Poor motor control Replace the controller Poor controller Replace controller A. Speed sensor installation inaccurate Check and reconnect E3 B. Poor speed sensor Replace the speed sensor Speed sensing failure C. Poor connection between speed sensor and controller Check and reconnect D. Poor controller Replace controller E5 A, running belt friction is too much Add silicon oil Over-current protection B, Controller is damaged Replace controller C, Motor damaged Replace motor motor line and motor defective Replace motor E2 Explosion-proof E6 motor abnormal Page 10 EXPLODED DRAWING Page 11 PARTS LIST No. Desc. 1 Front base 2 Spec. Main frame Qty Remark No. Desc. Spec. Qty 1 41 Incline adjustor 143*65*35 2 1 42 Belt 184 J6 1 3 Uprights 2 43 Silicone cushion 100*30*28 2 4 Console frame 1 44 Cushion 30*23*14 6 5 Runningboard reinforcement tube 1 45 Transport wheel ¢45*21*¢8.5 2 6 Front roller 1 46 Handrail plug Φ32 2 7 Rear roller 1 47 Power cord buckle 6p-4 1 8 Cylinder 1 48 Ring retaining wire plug ¢24*¢18*6 1 M10*105 2 49 Round head steel ball ¢27*¢10 2 φ28*M8*15 4 ¢30*T5*250 2 9 Hexagon head bolt 10 Hexagon head bolt M8*45 6 50 Adjustment foot pad 11 Hexagon head bolt M8*40 3 51 Handrail cover 12 Hexagon head bolt M8*25 1 52 Console 1 13 Hexagon head bolt M8*15 4 53 Display overlay decal 1 14 Hexagon cylindrical head bolt M8*15 4 54 Controller board 1 15 Hexagon cylindrical head bolt M8*12 4 55 Upper cable of console 1 16 Hexagon cylindrical head bolt M8*60 3 56 lower cable of console 1 17 Outer hexagonal bolt M8*75 1 57 Emergency stop key set 1 (25thread) 18 Hexagon countersunk head bolt M6*28 8 58 Emergency stop key sensor 1 19 Cross recessed large flat head screw M5*10 4 59 Pulse sensor set-Right 1 20 Self-drilling screw ST4*20 2 60 Pulse sensor set-Left 1 21 Cross recessed head tapping screw ST4*12 20 61 DC motor 1 22 Cross recessed round head tapping screw ST4*15 12 62 Power cable 1 23 Cross recessed round head tapping screw ST2.2*8 6 63 Rocker switch 1 24 Flat Washers Φ10*1.2 2 64 Overload 1 25 Flat Washers Φ8*1.2 6 65 Blue single branch wire 1 26 Internal serrated lock washer Φ8*1.2 15 66 Brown single branch wire 1 27 Lock nut M8 8 67 Brown single branch wire 1 28 Φ8 6 68 Blue single branch wire 1 29 Standard spring washer Motor cover 568*352*110 1 69 Ground wire 1 30 Bottom cover 540*318*21 1 70 31 Rear protect corner-Right 116*94*82 1 71 Magnetic ring 32 Rear protect corner-Left 116*94*82 1 72 Hexagon wrench 5# 1 33 Upright-cover-Right 200*140*65 1 73 Hexagon wrench 6# 1 34 Upright-cover-Left 200*140*65 1 74 Cross open-end wrench 14 15 1 35 Console panel 450*300*68 1 75 Inductance 36 Console upper cover 700*398*151 1 76 37 Running belt 2498*415*T1.6 1 77 38 Running board 1100*540*12 1 39 Side rail 1090*71.5*16 2 40 Side pedal stepper 380*80*8 2 Page 12 Optional Remark 1 Silicone oil 1 13 1 Optional 1 Optional MP3 module 1 Optional 78 USB module 1 Optional 79 speaker 2 Optional 80 Audio spring line 1 Optional Filter MAINTENANCE LUBRICATION Lubricating under the running belt will ensure superior performance and extend its life expectancy. After the first 25 hours of use (or 2-3 months) apply some lubricant, and repeat for every following 50 hours of use (or 5-8 months). How to check running belt for proper lubrication Lift one side of the running belt and feel the top surface of the running deck. If the surface is slick to the touch, then no further lubrication is required. If the surface is dry to the touch, apply some lubricant. How to apply lubricant Lift one side of running belt. Pour some lubricant under the centre of the running belt on the top surface of the running deck. Run on the treadmill at a slow speed for 3 to 5 minutes to evenly distribute lubricant. NOTE: DO NOT over lubricate running deck. Any excess lubricant that comes out should be wiped off. Lubricant Oil BELT ADJUSTMENT The running belt is pre-adjusted to the running deck at the factory, but after prolonged use it can stretch and require readjustment. To adjust the belt, turn on the main power switch of the treadmill Page 13 and let the belt run at a speed of 8-10 KPH. Use the 6 mm Allen Wrench provided to turn the rear roller adjustment bolts in order to centre the belt. If the running belt is shifting to the left, turn the left adjustment bolt 1/4 turn clockwise, and the running belt should start to correct itself. Tool: 6 mm Allen Wrench If the running belt is shifting to the right, then turn the right adjustment bolt 1/4 turn clockwise, and the belt should start to correct itself. Keep turning the adjustment bolts until the running belt is properly centered. Tool: 6 mm Allen Wrench If the running belt is slipping during use, turn off and unplug the treadmill. Using the 6 mm Allen Wrench provided, turn both left and right rear roller adjustment bolts 1/4 turn clockwise, then turn the main power switch back on and run the treadmill at a speed of 8-10 KPH. Run on to the running belt to determine if the belt is still slipping. Repeat this procedure until the belt no longer slips. Tool: 6 mm Allen Wrench Page 14 Product Specification Model IS0504A Packing dimension (cm) 16L x 76.5W x27H Product dimension (cm) 155L x 71W x 124H Net weight 42kg Gross weight 48kg Max load 110kg Colour Black Material Page 15 Steel, ABS, PP Contact Us ITSU WORLD SDN. BHD. No. 13, Lorong Technology B, Nouvelle Industrial Park, Taman Sains SG1 Kota Damansara,. PJU 5, 47810 Petaling Jaya, Malaysia Tel:+603 67323722 ITSU WORLD(HK)Limited Workshop D1,28/F,TML Tower No.3 Hoi Shing Road,Tsuen Wan,N.T. Tel:+852 36112228 PT Healthy World Lodan Center Block O No 20 Jalan Lodan Raya No 2 Jakarta Utara 14430 Tel:+62 21-69831123 Page 16 Fit Show APP Page 17 Download and operate bluetooth APP 2.Register and login 1). You need to register a new account and code if you are a new user, in order to keep your exercise record.If not, you can input your account and code,then enter it. 2).Please register with your E-mail or phone number, then input your registered fitshow account and code. 3.Link your phone and treadmill 1).Open bluetooth, APP will be searched treadmill that can be connected nearby, and automatically switch to your nearest treadmill. 2).Select more mode, you can choose the motion program you want to use by sliding left and right,include target mode,scene mode.Then, press START button to run. 4.Operation of mobile phone APP connecting with treadmill 1).Open mobile phone bluetooth:Ready state of treadmill, open mobile phone bluetooth 2).Connecting fitshow APP:a.open mobile phone fitshow APP. b.Press "search appliance" c.When the treadmill icon and bluetooth name (FS-BE9CB3) appears in the center of the mobile screen, press on the bottom of the mobile phone screen "connecting appliance" d.Press "START" button e.Mobile phone can show exercise parameter of treadmill Page 18 User Manual All information is correct at the time of print
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement