RF wireless LED remote controller
Model:SR-2819 with SR-1009Fxx
Brief introduction of buttons
Six zones/areas
Press-button RGBW controller
Receivers work with WIFI-RF convertor to be controlled by smart phone
Product introduction
SR-2819 RGBW remote controller has 6 different zones. It can get Red/ Green/ Blue/ White color directly. The remote controller can save up to 6 colors or 6 modes into corresponding buttons (1-6 positions) for each zone.
You can choose any color through color wheel. you can set the system as RGB 3-channeloutput, or RGBW 4channel output
Parameter
Remote
Part No.
SR-2819
Receiver
Part No.
SR-1009FA
SR-1009EA
SR-1009FA3
SR-1009FA7
Operation Voltage
3.6VDC
Operation
Frequency
434MHz/868MHz
Iuput Voltage
12-36VDC
12-36VDC
12-36VDC
12-36VDC
Current
4x5A
4x8A
4x350mA
4x700mA
DIMENSIONS
ø/h (mm)
48x140x16
Output
4x(60-180)W
4x(96-288)W
4x(4.2-12.6)W
4x(8.4-25.2)W
Remarks load 3pcs 7 AAA (1.5V) batteries
Remarks
Constant voltage
Constant voltage
Constant current
Constant current
Product Size
ON/OFF of all zones
Speed down under dynamic mode
Return previous status button
Save button: save up to 6 colors
or modes into 6 positions
(6-zone buttons)
6 zones: each zone can save
6 color or modes
R
1
G B
2 3
4 5 6
Wiring diagram
1)Receiver Connection Diagram for Single Unit
Power Supply
12-36VDC
110V-230VAC
Indicator: indicate the state of remote control
White channel: the 4th channel
Touch color wheel
Brightness: dim up
Speed up under dynamic mode
Brightness: dim down
Pause/Run button: 10 modes built-in
R/G/B channels
Learning Key
SR-1009FA
LED CONTROLLER
2) Receiver Connection Diagram for Multiple Units
Power Supply
12-36VDC
110V-230VAC
Note:
One receiver can work with 1-8pcs SR-2819
One SR-2819 control multiple receivers
The power supply chosen must be 20% higher than the actual load
Learning Key
SR-1009FA
LED CONTROLLER
Learning Key
SR-1009FA
LED CONTROLLER
140.0
Learning Key
SR-1009FA
LED CONTROLLER
Operation
Learning (matching) a. Do wiring according to connection diagram b. Wake up the remote control by touching ON/OFF button.
c. Press learning button on receiver.
d. Touch any zone button on remote control.
e. Then touch color wheel.
f. Connected LED light will blink to confirm zone designation.
g. Press at learning button on receiver over 5 seconds until LED light flash, then delete the learned ID.
Note 1: To choose a master from slaves by jumper for each zone.
Short circuit for master.
Open circuit for slave.
Each zone only can set one master controller. After a period of time, the master will do synchronization operation to keep the same color or mode of all slaves in one zone.
Note 2: Each remote control 8 zones (areas) receivers, each area can be learned as many receivers as we can.
Each receiver maximally can be controlled by 8 different remote controllers.
RGBW button of brightness.
Note: If you press R, then press G, then it is mix color of R and G. If you want to get G color directly, please press R to switch off of R first. Then press G.
Running&Pause Button a. Press pause&run button ,mode will run. Press it once, it runs one mode. Press button again, it stops, then press one more time, it will enter next mode. There are total 10 build-in modes.
b. Pause&run button can work with S button , it can save modes into different zone.
4 5 6
Press button. Zone 1,2,3,4,5,6 will run synchronized mode, after long press, LED lighting will flash twice, they will switch to chasing running mode, long press again to switch back.
Return button
Touch button to return previous color or running mode.
Speed up and Speed down Button
Touch button to speed down when mode is running, touch button to speed up when mode is running.
Brightness down or up button
Short/long press button to dim down brightness of RGB channels, Short/ long press button to dim up RGB channels.
“W” channel is separated from RGB channels, so we can only long press button to dimming“W” channel.
Save Button a. How to save color into different position per zone?
ZONE
Touch color wheel for select an ideal color
1 2 3
4 5 6
Press any zone button you want or
Select R/G/B/W color by press R G B
POSITION
Choose position( any button ) to save color
4 5 6
Long press button(the blue indicator will be on) for saving
For example, press zone button 1, then touch color wheel for orange color, then press S button
(the blue indicator will be on),then choose position button 3. That’s to say, we save orange color
from zone 1 into position 3.
So each zone can save 6 colors. 6 zones can save 36 colors.
b. How to save mode into different position per zone?
ZONE
1 2 3
4 5 6
Press any zone button you want
Press button for select an ideal mode
POSITION any button ) to save mode
Press button(the blue indicator will be on) for saving
4 5 6 c. Recall mode saved into.
4 5 6
Safety & Warnings
1) The product shall be installed and serviced by a qualified person.
2) IP20.Please avoid the sun and rain. When installed outdoors, please ensure it is mounted in a water proof enclosure.
3) Always be sure to mount this unit in an area with proper ventilation to avoid overheating.
4) Please check if the output voltage of any LED power supplies used comply with the working voltage of the product.
5) Never connect any cables while power is on and always assure correct connections to avoid short circuits before switching on.
6) Please ensure that the cable is secured tightly in the connector
7) For update information please consult your supplier.
Warranty Agreement
1) We provide lifelong technical assistance with this product:
3-year warranty. We print date on every products, for example :1125 means year 2011,week 25.The warranty is for free repair or replacement and covers manufacturing faults only.
For faults beyond the 3-year warranty we reserve the right to charge for time and parts.
2) Limited Warrenty
Any defects caused by wrong operation.
Any damages caused by unauthorized removal, maintenance, modifying, incorrect connection and replacement of chips.
Any damages due to transportation, vibration etc. after purchase.
Any damages caused by earthquake, fire, lightning, pollution and abnormal voltage.
Any damages caused by negligence, inappropriate storing at high temperatures and humidity or near harmful chemicals.
Product has been updated
3) Repair or replacement as provided under this warranty is the exclusive remedy to the customer.
