EPSON Stylus

®

Photo 825

1

Slide the paper support into its three slots on the back of the printer.

2

Slide the roll paper adapter behind the paper support, into the two slots on the back of the printer.

NOTE: For information on loading and

printing on roll paper, see your Printer

Basics book.

3

Insert the tabs on the roll paper holders into the slots on the back of the printer.

4

Unpack the ink cartridges that came with your printer and remove the yellow tape from the top.

CAUTION: Install both ink cartridges and leave them installed for all types of printing, or the printer won’t work.

5

Tilt each cartridge toward you as you lower it into the holder.

Make sure the tabs rest on the hooks in the back.

6

Lower the clamps so they snap shut.

7

Press the ink replacement button and close the cover.

The green light flashes as your printer charges ink for about 2 1 /

2 minutes.

CAUTION: Don’t turn off the printer or interrupt charging while the green light is flashing or you’ll waste ink.

CPD-14525R1

4042683-00

1

Plug the printer’s power cord into a grounded electrical outlet.

2

Press the dark gray power button to turn on the printer.

1

Remove everything from the box.

Ink cartridges Printer Software

CD-ROM

Printer Paper support

CompactFlash ™ card adapter

Roll paper holders

Roll paper adapter

2

Remove the tape and packing material.

Multi-card adapter

Printer Basics book

Quick Reference card

Peel off the plastic film

1

Open the output tray.

2

Open the printer cover.

3

Peel off the tape beneath the cover and remove the insert.

3

Lift up both ink cartridge clamps.

1

Load some paper against the right side of the feeder

(up to the arrow inside the edge guide).

2

Press in the tab on the edge guide and slide it to fit lightly against the paper stack.

3

Pull out the output tray extensions.

1

Make sure you have a USB cable (not included with your printer).

2

Plug the square end of the USB cable into your printer’s USB port.

Continue

3

Plug the flat end of the cable into any available USB port on your computer.

Turn over

Windows

If you’re using Windows Me or 2000, see “Installing Your Printer Software” in the Printer Basics book for instructions.

Follow the steps below to install the software for Windows XP or Windows 98.

Windows XP

1

Make sure your printer is connected and turned on.

Turn on your computer, if it isn’t already on.

2

Wait for Windows to detect your printer connection and display this screen:

DON’T CLICK ANY BUTTONS ON THE SCREEN YET.

NOTE: If this screen doesn’t appear, make sure your printer is turned on and fully connected.

3

Put the EPSON ® CD-ROM in your CD-ROM or

DVD drive and wait a few seconds for the

CD-ROM to be recognized.

Your printer software installs automatically and various messages appear on the screen.

4

Click Finish. You see another Found

New Hardware Wizard screen.

5

Click Next. More software is installed.

6

Click Finish. You see this message.

7

Click OK.

8

When you see the license agreement, click Agree.

9

When you see this screen, click Continue.

Now go to “Installing Optional Software” in the next column.

Windows 98

1

Make sure your printer is connected and turned on.

Turn on your computer, if it isn’t already on.

2

Wait for Windows 98 to detect your printer connection and display a screen like this:

DON’T CLICK ANY BUTTONS ON THE SCREEN YET.

NOTE: If this screen doesn’t appear, make sure your printer is turned on and fully connected.

3

Put the EPSON CD-ROM in your CD-ROM or DVD drive and wait a few seconds for the

CD-ROM to be recognized.

4

Click Next on the Add New Hardware Wizard screen.

5

Make sure the Search for option is selected, then click Next.

6

Click CD-ROM drive, then click Next.

7

At this screen, click Next.

Installation proceeds automatically.

When installation halts, click Finish.

Your computer detects your printer and you see a screen like this:

8

Continue clicking Next or Finish.

Installation proceeds automatically.

9

At the final Add New Hardware Wizard screen, click Finish. You see this message.

10

Click OK. When you see the license agreement, click Agree.

11

When you see this screen, click Continue.

Additional software is installed, then you see the EPSON PhotoStarter Setup screen.

12

Click Next and follow the on-screen instructions.

Do the same thing when you see the EPSON

CardMonitor Setup screen.

13

When setup is complete, select Yes to restart your computer and click Finish. Leave in the CD-ROM as your computer restarts.

Continue with the steps below to install optional software.

Macintosh

1

Make sure your printer is connected and turned on.

® Then turn on your Macintosh.

If you see this message, click Cancel.

2

Put the EPSON CD-ROM in your CD-ROM or DVD drive.

3

Mac ® OS X: Double-click the EPSON CD-ROM icon on the desktop to open it, then double-click the

EPSON OS X Installer icon.

Mac OS 8.6 to 9.x: Double-click the EPSON OS 8 and 9 Installer icon (you may have to double-click the

EPSON CD-ROM icon on the desktop to open the window).

4

Read and agree to the license agreement to continue the installation.

5

Click Install Printer Driver and Utilities and follow the on-screen instructions to install the software. Then restart your Macintosh.

6

For OS 8.6 to 9.x users, register your printer with EPSON after your Macintosh restarts.

7

Mac OS X: Open Print Center. If you don’t see your printer in the printer list, select EPSON USB in the pull-down menu on the Printer List screen, click SP 825(USB), and click Add. Close the Print Center.

Mac OS 8.6 to 9.x: Select the SP 825 icon in the Macintosh Choooser. Select your

USB port and turn on background printing. Then close the Chooser.

8

Mac OS X: Double-click the EPSON OS X Installer icon.

Mac OS 8.6 to 9.x: Double-click the EPSON OS 8 and 9 Installer icon.

9

Click Install Optional Software. You see this screen.

10

Click the button for each program to learn more about it.

If you want the program, click Install and follow the instructions on the screen.

11

When you’re finished installing software, close any open windows and click Back to return to the Install Menu.

12

Click Install Printer Manual.

13

For OS X users, if you want to print from Macintosh Classic applications as well as

OS X applications, start you Macintosh in OS 9 and repeat steps 3 through 11.

14

When you’re finished, click Exit. Remove the CD-ROM and keep it in case you need to reinstall any software later.

You’re ready to print! See section 8.

Continue

Installing Optional Software

1

At the Optional Software menu, click the button for each program to learn more about it. If you want the program, click Install and follow the instructions on the screen.

2

If you see a message about installing QuickTime, ® click Yes and follow the on-screen instructions.

You don’t need a registration number.

3

When you’re finished installing software, close any open windows.

4

Click Exit.

5

When you see the registration screen, register your printer with EPSON as instructed.

Remove the CD-ROM and keep it in case you need to reinstall any software later.

You’re ready to print! See section 8.

Now you’re ready to print. For instructions, use these resources:

• Your Printer Basics book

Learn about loading paper, printing, maintaining your printer, solving problems, and contacting EPSON.

• Your Quick Reference card

Keep it next to your printer for quick tips on printing without a computer.

• Your on-screen Reference Guide

Click the Printer Manual icon on your desktop to view more information about your printer.

EPSON and EPSON Stylus are registered trademarks of SEIKO EPSON CORPORATION.

General Notice: Other product names are for identification purposes only and may be trademarks of their respective owners.

EPSON disclaims any and all rights in those marks.

Printed on recycled paper.

Copyright © 2002 by Epson America, Inc. 12/02

Printed in XXX