Manitou Series 2 MT940L-TW (120) LS Rough Terrain Forklift Truck Operator/Service Manual
विज्ञापन
विज्ञापन
INTRODUCTION TO SAFETY
MANITOU NORTH AMERICA, INC.
6401 IMPERIAL DRIVE
WACO, TX 76712-6803
For Parts Orders contact your Manitou Dealer or call:
Manitou North Amerida, Inc. Parts Dept. (800) 425-3727 or (254) 799-0232.
Parts Dept. Fax (254) 867-6504 Website: www.manitou-na.com
MT940L-TW (120) LS
Series 2
OPERATOR/SERVICE
MANUAL
THIS OPERATOR'S MANUAL MUST BE KEPT IN THE LIFT TRUCK AND MUST BE READ
AND UNDERSTOOD BY THE LIFT TRUCK OPERATOR
547751AS
R05-05
INTRODUCTION TO SAFETY
INTRODUCTION TO SAFETY
- INTRODUCTION TO SAFETY -
- ROUGH TERRAIN FORKLIFT TRUCK
GENERAL SAFETY STANDARDS - - - - - - - - - - - I
- SAFETY MESSAGES - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - VII
- SAFETY DECALS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - VIII
- TABLE OF CONTENTS -
- OPERATING AND SAFETY INSTRUCTIONS - - - - - - - - - - - - - 1 - 1
- DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 - 1
- MAINTENANCE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3 - 1
- PICKING UP THE ATTACHMENTS - - - - - - - - - - - - - - - - - - - - 4 - 1
R05-05
INTRODUCTION TO SAFETY
INTRODUCTION TO SAFETY
ROUGH TERRAIN FORKLIFT TRUCK
GENERAL SAFETY STANDARDS
I
INTRODUCTION TO SAFETY
ROUGH TERRAIN FORKLIFT TRUCK GENERAL SAFETY STANDARDS
STUDY THE OPERATOR/SERVICE MANUALS
The information in this manual provides general instructions for the safe operation and maintenance of your forklift truck. This information is vital and must be clearly understood by the operator and serviceman. Study this manual and the Rough Terrain Forklift Safety Manual (part no. 422494) thoroughly and carefully before operating or servicing your forklift. Contact your dealer or Manitou North America, Inc. if you have any questions concerning your forklift, its operation, service or parts. Keep both manuals in the literature box on the forklift available for reference. If either manual becomes illegible or is missing, contact your dealer for replacements immediately. This manual cannot cover every situation that might result in an accident. It is the responsibility of the operator to always remain alert for potential hazards and be prepared to avoid them!
ADDITIONAL RECOMMENDED LITERATURE:
ANSI / ITSDF B56.6 is the national consensus standard for rough terrain forklift trucks. It contains rules about forklift safety, maintenance, safe operation, training, and supervision. Forklift owners should learn this standard and make it available for their operators, service personnel, and supervisors. These standards can be obtained, free of charge, from the Industrial Truck Standards Development Foundation (ITSDF) on their website at www.itsdf.org. The following references are examples from the standard, addressing forklift operators:
A.) OPERATOR TRAINING QUALIFICATIONS
1.) The user shall ensure that operators understand that safe operation is the operator’s responsibility. The user shall ensure that operators are knowledgeable of, and observe, all safety rules and practices.
2.) Create an effective operator training program centered around user company’s policies, operating conditions, and rough terrain forklift trucks. The program should be presented completely to all new operators and not be condensed for those claiming previous experience.
3.) Information on operator training is available from several sources, including rough terrain forklift truck manufacturers, users, government agencies, etc.
4.) An operator training program should consist of the following: a.) careful selection of the operator, considering physical qualifications, job attitude, and aptitude; b.) emphasis on safety of stock, equipment, operator, and other personnel; c.) citing of rules and why they were formulated; d.) basic fundamentals of rough terrain forklift truck and component design as related to safety, e.g., in.-lb (N-m) loading, mechanical limitations, center of gravity, stability, etc.; e.) introduction to equipment, control locations, and functions. Explain how they work when used properly and problems when used improperly.
f.) supervise practice on operating course remote from normal activity and designed to simulate actual operations, e.g., lumber stacking, elevating shingles to the roof, etc.; g.) oral, written, and operational performance tests and evaluations during and at completion of the course; h.) refresher courses, which may be condensed versions of the primary course, and periodic “on job” operator evaluation; i.) understanding of nameplate data and operator instructions and warning information appearing on the rough terrain forklift truck.
B.) GENERAL SAFETY PRACTICES
1.) Rough terrain forklift trucks can cause injury if improperly used or maintained.
2.) Only authorized operators trained to adhere strictly to all operating instructions shall be permitted to operate rough terrain forklift trucks. Unusual operating conditions may require additional safety precautions, training, and special operating instructions.
3.) Modifications and additions which affect capacity or safe operation shall not be preformed without the manufacturer’s prior written approval. Where such authorization is granted, capacity, operation, and maintenance instruction plates, tags, or decals shall be changed accordingly.
4.) If the rough terrain forklift truck is equipped with front end attachment(s) or optional forks, the user shall see that the truck is marked to identify the forks or attachment(s), show the approximate weight of the truck and fork or attachment combination, and show the capacity of the truck with forks or attachment(s) at maximum elevation with load laterally centered.
5.) The user shall see that all nameplates and caution and instruction markings are in place and legible.
6.) The user shall consider that changes in load dimension may affect rough terrain forklift truck capacity.
II
INTRODUCTION TO SAFETY
ROUGH TERRAIN FORKLIFT TRUCK GENERAL SAFETY STANDARDS (cont.)
B.) GENERAL SAFETY PRACTICES (cont.)
7.) Where steering can be accomplished with either hand and the steering mechanism is of a type that prevents road reactions from causing the handwheel to spin (power steering or equivalent), steering knobs may be used. When used, steering knobs shall be of a type that can be engaged by the operator’s hand from the top and shall be within the periphery of the steering handwheel.
8.) Experience has shown that rough terrain forklift trucks which comply with stability requirements are stable when properly operated. However, improper operation, faulty maintenance, or poor housekeeping may contribute to a condition of instability and defeat the purpose of the requirements.
9.) Users shall give consideration to special operating conditions. The amount of forward and rearward tilt to be used is governed by the application. Although the use of maximum rearward tilt is allowable under certain conditions, such as traveling with the load lowered, the stability of a rough terrain forklift truck as determined by standardized tests does not encompass consideration for excessive tilt at high elevations or the operation of trucks with excessive off-center loads.
10.) Some of the conditions which may affect stability are ground and floor conditions, grade, speed, loading
(rough terrain forklift trucks equipped with attachments behave as partially loaded trucks even when operated without a load on the attachment), dynamic and static forces, improper tire inflation, and the judgement exercised by the operator.
C.) OPERATING SAFETY RULES AND PRACTICES
1.) Safe operation is the responsibility of the operator.
2.) This equipment can be dangerous if not used properly. The operator shall develop safe working habits and also be aware of hazardous conditions in order to protect himself, other personnel, the rough terrain forklift truck, and other material.
3.) The operator shall be familiar with the operation and function of all controls and instruments before undertaking to operate the rough terrain forklift truck.
4.) Before operating any rough terrain forklift truck, truck operators shall have read and be familiar with the operator’s manual for the particular truck being operated.
5.) Before starting to operate the rough terrain forklift truck: a.) be in operating position and fasten seat belt; b.) place directional controls in neutral; c.) apply brakes; d.) start engine.
6.) Do not start or operate the rough terrain forklift truck, any of its functions, or attachments from any place other than the designated operator’s position.
7.) Keep hands and feet inside the operator’s designated area or compartment. Do not put any part of the body outside the operator compartment of the rough terrain forklift truck.
8.) Never put any part of the body into the mast structure or between the mast and the rough terrain forklift truck.
9.) Never put any part of the body within the reach mechanism of the rough terrain forklift truck or other attachments.
10.) Understand rough terrain forklift limitations and operate the truck in a safe manner so as not to cause injury to personnel.
11.) Do not allow anyone to stand or pass under the elevated portion of any rough terrain forklift truck, whether empty or loaded.
12.) Do not permit passengers to ride on rough terrain forklift trucks.
13.) Check clearance carefully before driving under electrical lines, bridges, etc.
14.) A rough terrain forklift truck is attended when the operator is less than 25 ft (7.6m) from the truck, which remains in his view.
15.) A rough terrain forklift truck is unattended when the operator is 25ft (7.6m) or more from the truck, which remains in his view, or whenever the operator leaves the truck and it is not in his view.
16.) Before leaving the operator’s position: a.) bring rough terrain forklift truck to a complete stop; b.) place directional controls in neutral; c.) apply the parking brake; d.) lower load-engaging means fully, unless supporting an occupied elevated platform; e.) stop the engine; f.) if the rough terrain forklift truck must be left on an incline, block the wheels; g.) fully lower the load-engaging means.
17.) Maintain a safe distance from the edge of ramps, platforms, and other similar working surfaces.
18.) Do no move railroad cars or trailer with a rough terrain forklift truck.
III
INTRODUCTION TO SAFETY
ROUGH TERRAIN FORKLIFT TRUCK GENERAL SAFETY STANDARDS (cont.)
C.) OPERATING SAFETY RULES AND PRACTICES (cont.)
19.) Do not use a rough terrain forklift truck for opening or closing railroad car doors.
20.) In areas classified as hazardous, use only rough terrain forklift trucks approved for use in those areas.
21.) Report all accidents involving personnel, building structures, and equipment to the supervisor or as directed.
22.) Do not add to, or modify, the rough terrain forklift truck.
23.) Do not block access to fire aisles, stairways, and fire equipment.
24.) For rough terrain forklift trucks equipped with a differential lock, the lock should not be engaged when driving on the road or at high speeds or when turning. If the lock is engaged when turning, there could be loss of steering control.
25.) Observe all traffic regulations including authorized speed limits. Under normal traffic conditions, keep to the right, maintain a safe distance, based on speed of travel, from the truck ahead; and keep the truck under control at all times.
26.) Yield the right-of-way to pedestrians and emergency vehicles such as ambulances and fire trucks.
27.) Do not pass another truck traveling in the same direction at intersections, blind spots, or at other dangerous locations.
28.) Slow down and sound the audible warning device(s) at cross-aisles and other locations where vision is obstructed.
29.) Cross railroad tracks at an angle wherever possible. Do not park closer than 6 ft (1.8m) to the nearest rail of a railroad track.
30.) Keep a clear view of the path of travel and observe other traffic, personnel, and safe clearances.
31.) If the load being carried obstructs forward view, travel with the load trailing.
32.) Ascend or descend grades slowly and with caution.
a.) When ascending or descending grades in excess of 5%, loaded rough terrain forklift trucks should be driven with the load upgrade.
b.) Unloaded rough terrain forklift trucks should be operated on all grades with the load-engaging means downgrade.
c.) On all grades, the load and load-engaging means shall be tilted back, if applicable, and raised only as far as necessary to clear the road surface.
d.) Avoid turning, if possible, and use extreme caution on grades, ramps, or inclines; normally travel straight up or down.
33.) Under all travel conditions, operate the rough terrain forklift truck at a speed that will permit it to be brought to a stop in a safe manner.
34.) Travel with load-engaging means or load low and, where possible, tilted back. Do not elevate the load except during stacking.
35.) Make starts, stops, turns, or direction reversals in a smooth manner so as not to shift load and/or overturn the rough terrain forklift truck.
36.) Do not indulge in stunt driving or horseplay.
37.) Slow down for wet and slippery surfaces.
38.) Before driving over a dockboard or bridge plate, be sure that it is properly secured. Drive carefully and slowly across the dockboard or bridge plate, and never exceed its rated capacity.
39.) Do not drive rough terrain forklift trucks onto any elevator unless specifically authorized to do so.
Approach elevators slowly, and then enter squarely after the elevator car is properly leveled. Once on the elevator, neutralize the controls, shut off engine, and set brakes. It is advisable that all other personnel leave the elevator before truck is allowed to enter or leave.
40.) Avoid running over loose objects on the roadway surface.
41.) When negotiating turns, reduce speed to a safe level, and turn steering handwheel in a smooth sweeping motion. Except when maneuvering at a very low speed, turn the steering handwheel at a moderate, even rate.
42.) Use special care when traveling without load, as the risk of lateral overturning is greater.
43.) Improper use of stabilizer controls (if so equipped) could cause rough terrain forklift truck upset. Always lower the carriage before operating stabilizer controls.
44.) For rough terrain forklift trucks equipped with lateral leveling: a.) Always level the frame before raising the boom or mast, with or without a load.
b.) Lateral leveling should not be used to position an elevated load; instead, lower the load and reposition the rough terrain forklift truck.
45.) Handle only stable or safely arranged loads.
a.) When handling off-center loads which cannot be centered, operate with extra caution.
b.) Handle only loads within the capacity of the rough terrain forklift truck.
c.) Handle loads exceeding the dimensions used to establish rough terrain forklift truck capacity with extra caution. Stability and maneuverability may be adversely affected.
IV
INTRODUCTION TO SAFETY
ROUGH TERRAIN FORKLIFT TRUCK GENERAL SAFETY STANDARDS (cont.)
C.) OPERATING SAFETY RULES AND PRACTICES (cont.)
46.) When attachments are used, extra care shall be taken in securing, manipulating, positioning, and transporting the load. Operate rough terrain forklift trucks equipped with attachments as partially loaded trucks when not handling a load.
47.) Completely engage the load with the load-engaging means. Fork length should be at least two-thirds of load length. Where tilt is provided, carefully tilt the load backward to stabilize the load. Caution should be used in tilting backward with high or segmented loads.
48.) Use extreme care when tilting load forward or backward, particularly when high tiering. Do not tilt forward with load-engaging means elevated except to pick up or deposit a load over a rack or stack. When stacking or tiering, use only enough backward tilt to stabilize the load.
49.) The handling of suspended loads by means of a crane arm (boom) or other device can introduce dynamic forces affecting the stability of a rough terrain forklift truck. Grades and sudden starts, stops, and turns can cause the load to swing and create a hazard if not externally stabilized. When handling suspended loads: a.) do not exceed the truck manufacturer’s capacity of the rough terrain forklift truck as equipped for handling suspended loads.
b.) only lift the load vertically and never drag it horizontally; c.) transport the load with the bottom of the load and the mast as low as possible; d.) with load elevated, maneuver the rough terrain forklift truck slowly and cautiously, and only to the extent necessary to permit lowering to the transport position; e.) use tag lines to restrain load swing whenever possible.
50.) At the beginning of each shift and before operating the rough terrain forklift truck, check its condition, giving special attention to: a.) tires and their inflation pressure b.) warning devices c.) lights d.) lift and tilt systems, load-engaging means, chains, cables, and limit switches e.) brakes f.) steering mechanism g.) fuel system(s)
51.) If the rough terrain forklift truck is found to be in need of repair or in any way unsafe, or if it contributes to an unsafe condition, the matter shall be reported immediately to the user’s designated authority, and the truck shall not be operated until it has been restored to safe operating condition.
52.) If during operation the rough terrain forklift truck becomes unsafe in any way, the matter shall be reported immediately to the user’s designated authority, and the truck shall not be operated until it has been restored to safe operating condition.
53.) Do not make repairs or adjustments unless specifically authorized to do so.
54.) When refueling, smoking in the area shall not be permitted, the engine shall be stopped, and the operator shall not be on the rough terrain forklift truck.
55.) Spillage of oil or fuel shall be carefully and completely absorbed or evaporated and fuel tank cap replaced before restarting engine.
56.) Do not use open flames when checking electrolyte level in storage batteries, liquid level in fuel tanks, or the condition of LPG fuel lines and connectors.
57.) Do not lift personnel with the forklift. If the forklift must be used to lift people, precautions for the protection of the personnel must be taken (see ITSDF B56.6, chapter 5.15 Elevating Personnel).
V
INTRODUCTION TO SAFETY
ROUGH TERRAIN FORKLIFT TRUCK GENERAL SAFETY STANDARDS (cont.)
CONCLUSION:
1.) ATTEND OPERATOR TRAINING CLASSES
The forklift operator must clearly understand all instructions concerning the safe operation of the forklift and all safety rules and regulations of the work site. They must have successfully completed a training coarse in accordance with the Powered Industrial Truck Standard (29 CFR 1910.178) as described by the Occupational
Safety and Health Administration (OSHA). They must be qualified as to their visual, hearing, physical, and mental ability to operate the equipment safely. NEVER use drugs or alcohol while operating a forklift! NEVER operate or allow anyone to operate a forklift when mental alertness or coordination is impaired! An operator on prescription or over-the-counter drugs must consult a medical professional regarding any side effects of the medication that may impair their ability to safely operate the forklift.
2.) CREATE A MAINTENANCE PROGRAM
OSHA recommends a maintenance log, listing repairs requested and completed, for each forklift. Also, “lock out tag procedures” should be utilized. If the forklift malfunctions; park it safely, remove the key, tag “Do Not
Use”, and report the problem to the proper authority or authorized service personnel immediately. For the best forklift performance and operation, a maintenance program is required. Use the hour meter on the instrument panel to keep maintenance properly scheduled (see SECTION TWO - “Servicing Schedule”). For repairs on major components (engine, transmission, etc.), contact your nearest dealer for a Repair Manual. Do not operate a forklift that is damaged or does not function properly. Only authorized personnel may make repairs or adjustments to the lift truck. After repairs, the lift truck must be tested for safe operation before returning to service.
3.) FORKLIFT KNOWLEDGE
Forklift trucks can cause serious injury if improperly used or maintained. Study all of the manuals provided for your forklift model. Learn the locations and meanings of all safety decals. If any decals are illegible or missing, have them replaced immediately. Make sure all safety features provided by the original manufacturer are in place and function properly. Do not operate a forklift with damaged, missing or unsafe components. Have it repaired by authorized service personnel. Learn the functions of all controls, gauges, indicator lights, etc. on the forklift. Know the speed/gear ranges, braking and steering capabilities, load ratings and clearances. When referring to the location of forklift components, the terms “left”, “right”, “front”, and “rear” are related to the operator seated normally, facing forward in the operator’s seat. If you have any questions about the forklift, consult your supervisor. Failure to fully understand or obey safety warnings can result in serious injury or death!
4.) WORK SITE KNOWLEDGE
Before operating on a work site, learn the rules for movement of people, forklifts and all other traffic. Check the size, weight, and condition of the loads you will be expected to handle. Verify that they are properly secured and safe to transport. Learn where the loads are to be placed, planning your route for a safe approach, watching for hazardous conditions. Will a signal man be required to help place the load? Remove any debris which may cause tire damage or rupture. Plan your route around problem areas or have them corrected. Inform the supervisor of any unsafe conditions observed at the site. Examples of hazards: power lines, cables, low clearance structures, garage doors, telephone pole guide lines, fencing, loose lumber, building materials, drop-offs, trenches, rough/soft spots, oil spills, deep mud, steep inclines, railroad tracks, curbs, etc.. NEVER approach power lines, gas lines or other utilities with the forklift! Always verify that local, state/provincial and federal regulations have been met. Report any accidents involving personnel, building structures, and equipment to the supervisor immediately. Always remain alert - conditions are constantly changing at the work site!
TECHNICAL SUPPORT
All data provided in this manual is subject to production changes, addition of new models, and improved product designs. If a question arises regarding your forklift, please consult your dealer or Manitou North America,
Inc. for the latest information. When ordering service parts or requesting technical information, be prepared to quote the applicable Model/Serial Numbers.
VI
INTRODUCTION TO SAFETY
SAFETY MESSAGES
NOTE THE SAFETY ALERT SYMBOL (SHOWN BELOW). IT IDENTIFIES POTENTIAL
HAZARDS WHICH, IF NOT AVOIDED MAY RESULT IN INJURY OR DEATH!
Observe the safety messages placed throughout this manual; providing special instructions, telling you when to take precautions and identify potential hazards.
SAFETY ALERT SYMBOL
The safety messages are highlighted in bold, italicized text.
CALIFORNIA PROPOSITION 65 WARNING
Diesel Engine Exhaust and some of its constituents are known to the State of California to cause cancer, birth defects or other reproductive harm.
WARNING: Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling.
VII
INTRODUCTION TO SAFETY
SAFETY DECALS
The purpose of this chapter is to introduce you to the safety messages, decals, and nameplates found on your forklift truck. The decals are identified by name, part number, location, and a brief description. (The forklift model logos, and other misc. decals not shown, can be found in your forklift parts manual.) The decals illustrated may not be exactly the same as those installed on your forklift; installation of the decals varies depending on the forklift model, series, decal updates, etc.. The size and location of some decals limit the amount of information that can be placed upon it. For this reason, additional detailed information not found on the decals is provided through-out this manual.
Every decal placed on the lift truck is important; they are constant reminders of safety and instructions that should never be taken for granted. Even experienced operators can be seriously injured or killed by ignoring, refusing to enforce, or forgetting to follow safe operating procedures! Do not assume you know all safety issues concerning the decals. Before operating the lift truck; learn the meaning(s) of the decals as described in this manual. If any decal becomes illegible or missing, have it replaced immediately! Always replace decals using the same decal part no., unless otherwise specified by the manufacturer. For replacement decals not found in your parts manual, contact your nearest dealer. If you have any questions, contact your supervisor or nearest dealer for advice before operating your forklift!
801011
Before Starting - 801011
(Boom equipped models). Location: on the brake fluid cover panel (to the left and below the dash panel).
Safety Instructions - 420792
(Mast equipped models). Location: on or near the operator manual storage case, and/or on the dash panel.
Instructions for the forklift operator; before operating the forklift.
Use of Seat Belt - 801012
(Boom equipped models). Location: to the right of the operator, near the hydraulic control lever.
Instructs the operator to always wear the seat belt during operations, and never jump from an over-turning forklift.
VIII
INTRODUCTION TO SAFETY
SAFETY DECALS
Emergency and Parking Brake - 801010
Location: near the park brake lever.
Identifies the Emergency/Parking Brake Lever.
Alarm Must Sound - 496162
Location: on the dash, in direct view of the operator.
The backup alarm must sound when the forklift is placed in reverse gear.
No Riders - 420732
Location: on the cab entrance(s), and on or near wheel fenders and engine cover.
Informs: riders are not allowed on the forklift.
Clear of Raised Boom - 801006
(Boom equipped models). Location: on both sides of the boom nose.
Keep away from unsupported boom.
Clear of Power Lines - 801007
(Boom equipped models). Location: on both sides of the boom nose.
Keep away from power lines.
IX
INTRODUCTION TO SAFETY
SAFETY DECALS
Use of Frame Leveling - 801013
(Boom equipped models). Location: to the right of the operator near the hydraulic control lever.
Frame leveling notice; load must be lowered.
Attachment and Boom Safety - 801009
(Boom equipped models). Location: on both sides of the boom nose.
Important reminders of attachment and boom safety.
Hydraulic Coupling - 234805
Location: near the quick-disconnect adapters.
Stop the engine and release hydraulic pressure before changing attachments.
Rotating Fan and Belt(s) - 801008
Location: on the radiator near the fan, and on any fan belt/pulley cover(s).
Keep hands and clothing away from rotating fan and belts.
X
INTRODUCTION TO SAFETY
SAFETY DECALS
Gear Shift Pattern - 33460
(4-speed transmission models). Location: near the gear shift lever.
Identifies the gear shift pattern of the forklift transmission.
Steering Mode - 184276
(4 wheel steer equipped models). Location: near the steering mode selection lever.
Identifies the steering mode selection.
Mineral Oil (Brake Reservoir) - 221322 or 234800 has been replaced by 164091.
Location: near the brake fluid reservoir where applicable.
Refer to the Operator/Service Manual for the correct brake fluid
(mineral oil) to be used in the brake system.
221322
234800
XI
INTRODUCTION TO SAFETY
SAFETY DECALS
Hydraulic Oil - 234798 or 76573
Location: on the hydraulic tank or filler cap.
Identifies the hydraulic reservoir (tank) or filler cap.
Hydraulic Oil - 61024
Location: on the hydraulic tank.
Identifies the hydraulic reservoir (tank).
Anti-Freeze - 234799
Location: on the radiator, near the radiator filler cap.
Indicates required minimum to maximum anti-freeze protection (-22
0
F to -40
0
F).
Diesel Fuel - 161101
Location: on the fuel tank, near the filler cap.
Identifies the fuel tank, and use of diesel fuel.
No Step - 496735
Location: varies, depending on the forklift model.
Instructs personnel not to use the designated area as a step.
Do Not Tow - 494918
(Hydrostatic equipped models). Location: on the dash, in view of the operator.
Towing the forklift will damage the transmission; refer to the operator’s manual.
XII
INTRODUCTION TO SAFETY
SAFETY DECALS
Attachment Warning - 421016
(Boom equipped models). Location: on the boom coupler, near where the retaining shaft is installed.
Reminder to operator; install attachment retaining shaft and safety pin before operations.
Hook Here - 24653
Location: at points provided on the forklift, where straps or chains may be attached to secure the forklift to a trailer during transport.
Fork Safety - 426641
(Mast equipped models). Location: on the front and back side of the mast’s outer rails, at eye level (4 required).
Instructs personnel not to travel beneath or upon the lift truck forks.
Pinch Point, Large, 2.5 x 4.5 in. - 426643
Pinch Point, Small, 1.5 x 2.75 in. - 426642
(Mast equipped models). Location: on the front and rear sides of the mast cross bracing.
Keep fingers away from the mast crossbracing.
HAND THROTTLE DANGER - 804784
(Boom equipped models, option). Location: Near the hand throttle mechanism.
Reminder to operator; set parking brake before operating hand throttle.
Disengage hand throttle before leaving the forklift.
XIII
INTRODUCTION TO SAFETY
SAFETY DECALS
Acid in Battery - 801014
Location: in or near the battery storage compartment.
Addresses battery hazards.
Jump Start Battery - 801015
Location: in or near the battery storage compartment.
Jump start instructions.
Attachment Plate - 425995
Location: on the optional removeable forklift attachment.
Important manufacturer information about the attachment. Record this information for use when contacting the maufacturer for parts and service.
Overhead Guard Data Plate - B6109
Location: attached to the overhead guard.
Overhead guard conformity.
Forklift Data Plate - 496550
(Boom equipped models)
Forklift Data Plate - 496538
(Mast equipped models)
Location: within the operator’s compartment.
Important forklift truck identification. Record this information for use when contacting the manufacturer for parts and service.
496550
496538
XIV
INTRODUCTION TO SAFETY
TABLE OF CONTENTS
PERATING AND SAFETY INSTRUCTIONS
– IDENTIFICATION OF THE LIFT TRUCK
– CHARACTERISTICS
USA MODEL -
MT 845 Série 2 + T + T M-U
MT 940 L Série 2 + T + T M-U
MT 1233 S Série 2 + T + T M-U
MT 1240 L Série 2 + T + T M-U
MT 1330 SL Série 2 + T
MT 1337 SL Série 2 + T + T M-U
MT 1637 SL Série 2 + T + T M-U
MT 1740 SL Série 2 + T
– DIMENSIONS AND LOAD CHART
USA MODEL -
MT 1337 SL Série 2 + T + T M-U
MT 1637 SL Série 2 + T + T M-U
– DESCRIPTION AND USE OF ELECTRIC AND HYDRAULIC OPTIONS
– FILTERS CARTRIDGES AND BELTS
– A - DAILY OR EVERY 10 HOURS SERVICE
– E - EVERY 1000 HOURS SERVICE
– F - EVERY 2000 HOURS SERVICE
DAPTABLE ATTACHMENTS IN OPTION ON THE RANGE
INTRODUCTION TO SAFETY
INTRODUCTION TO SAFETY
1 -
OPERATING
1 - 1
INTRODUCTION TO SAFETY
1 - 2
INTRODUCTION TO SAFETY
TABLE OF CONTENTS
I
NSTRUCTIONS TO THE COMPANY MANAGER
THE OPERATOR
THE LIFT TRUCK
A - THE LIFT TRUCK'S SUITABILITY FOR THE JOB
B - ADAPTATION OF THE LIFT TRUCK TO STANDARD ENVIRONMENTAL CONDITIONS
C - MODIFICATION OF THE LIFT TRUCK
THE INSTRUCTIONS
THE MAINTENANCE
I
NSTRUCTIONS FOR THE OPERATOR
PREAMBULE
GENERAL INSTRUCTIONS
A - OPERATOR'S MANUAL
B - AUTHORIZATION FOR USE IN FRANCE
(or see current legislation in other countries)
C - MAINTENANCE
D - MODIFICATION OF THE LIFT TRUCK
E - LIFTING PEOPLE
OPERATING INSTRUCTIONS UNLADEN AND LADEN
A - BEFORE STARTING THE LIFT TRUCK
B - DRIVER’S OPERATING INSTRUCTIONS
C - ENVIRONMENT
D - VISIBILITY
E - STARTING THE LIFT TRUCK
F - DRIVING THE LIFT TRUCK
G - STOPPING THE LIFT TRUCK
H - DRIVING THE LIFT TRUCK ON THE PUBLIC HIGHWAY
INSTRUCTIONS FOR HANDLING A LOAD
A - CHOICE OF ATTACHMENTS
B - MASS OF LOAD AND CENTRE OF GRAVITY
C - N/A
D - TRANSVERSE ATTITUDE OF THE LIFT TRUCK
E - TAKING UP A LOAD ON THE GROUND
F - TAKING UP AND LAYING A HIGH LOAD ON TYRES
G - TAKING UP AND LAYING A HIGH LOAD ON STABILIZERS
M
AINTENANCE INSTRUCTIONS OF THE LIFT TRUCK
GENERAL INSTRUCTIONS
MAINTENANCE
LUBRICANT AND FUEL LEVELS
HYDRAULIC
ELECTRICITY
WELDING
WASHING THE LIFT TRUCK
I
F THE LIFT TRUCK IS NOT TO BE USED FOR A LONG TIME
INTRODUCTION
PREPARING THE LIFT TRUCK
PROTECTING THE I.C. ENGINE
PROTECTING THE LIFT TRUCK
BRINGING THE LIFT TRUCK BACK INTO SERVICE
1 - 3
INTRODUCTION TO SAFETY
INSTRUCTIONS TO THE COMPANY MANAGER
T
HE OPERATOR
- Only qualified, authorized personnel can use the lift truck. This authorization is given in writing by the appropriate person in the establishment with respect to the use of lift trucks and must be carried permanently by the operator.
On the basis of experience, there are a number of possible situations in which operating the lift truck is contra-indicated. Such foreseeable abnormal uses, the main ones being listed below, are strictly forbidden.
- The foreseeable abnormal behaviour resulting from ordinary neglect, but does not result from any wish to put the machinery to any improper use.
- The reflex reactions of a person in the event of a malfunction, incident, fault, etc. during operation of the lift truck.
- Behaviour resulting from application of the "principle of least action" when performing a task.
- For certain machines, the foreseeable behaviour of such persons as : apprentices, teenagers, handicapped persons, trainees tempted to drive a lift truck, operator tempted to operate a truck to win a bet, in competition or for their own personal experience.
The person in charge of the equipment must take these criteria into account when assessing whether or not a person will make a suitable driver.
T
HE LIFT TRUCK
A - THE LIFT TRUCK'S SUITABILITY FOR THE JOB
- MANITOU has ensured that this lift truck is suitable for use under the standard operating conditions defined in this operator's manual, with a STATIC test coefficient of 1.33 and a DYNAMIC test coefficient of 1, as specified in harmonised norm EN 1459 for variable range trucks.
- Before commissioning, the company manager must make sure that the lift truck is appropriate for the work to be done, and perform certain tests (in accordance with current legislation).
B - ADAPTATION OF THE LIFT TRUCK TO STANDARD ENVIRONMENTAL CONDITIONS
- In addition to series equipment mounted on your lift truck, many options are available, such as : road lighting, stop lights, flashing light, reverse lights, reverse buzzer alarm, front light, rear light, light at the jib head, etc.
- The operator must take into account the operating conditions to define the lift truck's signalling and lighting equipment. Contact your dealer.
- Take into account climatic and atmospheric conditions of the site of utilisation.
. Protection against frost (see : 3 - MAINTENANCE : LUBRICANTS AND FUEL).
. Adaptation of lubricants (ask your dealer for information).
. I.C. engine filtration (see : 3 - MAINTENANCE : FILTERS CARTRIDGES AND BELTS).
For operation under average climatic conditions, i.e. : between -15 °C and + 35 °C, correct levels of lubricants in all the circuits are checked in production. For operation under more severe climatic conditions, before starting up, it is necessary to drain all the circuits, then ensure correct levels of lubricants using lubricants properly suited to the relevant ambient temperatures. It is the same for the cooling liquid.
- A lift truck operating in an area without fire extinguishing equipment must be equipped with an individual extinguisher. There are solutions, consult your dealer.
Your lift truck is designed for outdoor use under normal atmospheric conditions and indoor use in suitably aerated and ventilated premises.
It is prohibited to use the lift truck in areas where there is a risk of fire or which are potentially explosive (e.g. Refineries, fuel or gas depots, stores of inflammable products…). For use in these areas, specific equipment is available (ask your dealer for information).
C - MODIFICATION OF THE LIFT TRUCK
- For your safety and that of others, you must not change the structure and settings of the various components used in your lift truck (hydraulic pressure, calibrating limiters, I.C. engine speed, addition of extra equipment, addition of counterweight, unapproved attachments, alarm systems, etc.) yourself. In this event, the manufacturer cannot be held responsible.
1 - 4
INTRODUCTION TO SAFETY
T
HE INSTRUCTIONS
- The operator's manual must always be in good condition and kept in the place provided on the lift truck and in the language used by the operator.
- The operator's manual and any plates or stickers which are no longer legible or are damaged, must be replaced immediately.
T
HE MAINTENANCE
- Maintenance or repairs other than those detailed in part : 3 - MAINTENANCE must be carried out by qualified personnel (consult your dealer) and under the necessary safety conditions to maintain the health of the operator and any third party.
Your lift truck must be inspected periodically to ensure that it remains in compliance. The frequency of this inspection is defined by current legislation in the country in which the lift truck is used.
1 - 5
INTRODUCTION TO SAFETY
INSTRUCTIONS FOR THE OPERATOR
P
REAMBULE
WHENEVER YOU SEE THIS SYMBOL IT MEANS :
WARNING ! BE CAREFUL ! YOUR SAFETY OR THE SAFETY OF THE LIFT TRUCK IS AT RISK.
The risk of accident while using, servicing or repairing your lift truck can be restricted if you follow the safety instructions and safety measures detailed in these instruction.
- Only the operations and manœuvres described in these operator's manual must be performed. The manufacturer cannot predict all possible risky situations. Consequently, the safety instructions given in the operator's manual and on the lift truck itself are not exhaustive.
- At any time, as an operator, you must envisage, within reason, the possible risk to yourself, to others or to the lift truck itself when you use it.
Failure to respect the safety and operating instructions, or the instructions for repairing or servicing your lift truck may lead to serious, even fatal accident.
G
ENERAL INSTRUCTIONS
A - OPERATOR'S MANUAL
- Read the operator's manual carefully.
- The operator's manual must always be in good condition and in the place provided for it on the lift truck.
- You must report any plates and stickers which are no longer legible or which are damaged.
B - AUTHORIZATION FOR USE IN FRANCE
(or see current legislation in other countries)
- Only qualified, authorized personnel may use the lift truck. This authorization is given in writing by the appropriate person in the company, in charge of using the lift truck, and must be permanently carried by the operator.
- The operator is not competent to authorise the driving of the lift truck by another person.
C - MAINTENANCE
- The operator must immediately advise his superior if his lift truck is not in good working order or does not comply with the safety notice.
- The operator is prohibited from carrying out any repairs or adjustments himself, unless he has been trained for this purpose. He must keep the lift truck properly cleaned if this is among his responsibilities.
- The operator must carry out daily maintenance (see : 3 - MAINTENANCE : A - DAILY OR EVERY 10 HOURS SERVICE).
- The operator must ensure tyres are adapted to the nature of the ground (see area of the contact surface of the tyres in the chapter : 2 - DESCRIPTION : CHARACTERISTICS). There are optional solutions, consult your dealer.
. SAND tyres.
. LAND tyres.
. Snow chains.
Do not use the lift truck if the tyres are incorrectly inflated, damaged or excessively worn, because this could put your own safety or that of others at risk, or cause damage to the lift truck itself. The fitting of foam inflated tyres is prohibited and is not guaranteed by the manufacturer, excepting prior authorisation.
D - MODIFICATION OF THE LIFT TRUCK
- For your safety and that of others, you must not change the structure and settings of the various components used in your lift truck (hydraulic pressure, calibrating limiters, I.C. engine speed, addition of extra equipment, addition of counterweight, unapproved attachments, alarm systems, etc.) yourself. In this event, the manufacturer cannot be held responsible.
1 - 6
INTRODUCTION TO SAFETY
E - LIFTING PEOPLE
- The use of working equipment and load lifting attachments to lift people is strictly forbidden
ORH
ORH
1 - 7
INTRODUCTION TO SAFETY
O
PERATING INSTRUCTIONS UNLADEN AND LADEN
A - BEFORE STARTING THE LIFT TRUCK
- Carry out daily maintenance (see : 3 - MAINTENANCE : A - DAILY OR EVERY 10 HOURS SERVICE).
- Make sure the lights, indicators and windscreen wipers are working properly.
- Make sure the rear view mirrors are in good condition, clean and properly adjusted.
- Make sure the horn works.
B - DRIVER’S OPERATING INSTRUCTIONS
- Whatever his experience, the operator is advised to familiarize himself with the position and operation of all the controls and instruments before operating the lift truck.
- Wear clothes suited for driving the lift truck, avoid loose clothes.
- Make sure you have the appropriate protective equipment for the job to be done.
- Prolonged exposure to high noise levels may cause hearing problems. It is recommended to wear ear muffs to protect against excessive noise.
- Always face the lift truck when getting into and leaving the driving seat and use the handle(s) provided for this purpose. Do not jump out of the seat to get down.
- Always pay attention when using the lift truck. Do not listen to the radio or music using headphones or earphones.
- Never operate the lift truck when hands or feet are wet or soiled with greasy substances.
- For increased comfort, adjust the seat to your requirements and adopt the correct position in the driver’s cab.
Under no circumstances must the seat be adjusted while the lift truck is moving.
- The operator must always be in his normal position in the driver’s cab. It is prohibited to have arms or legs, or generally any part of the body, protruding from the driver’s cab of the lift truck.
- The safety belt must be worn and adjusted to the operator's size.
- The control units must never in any event be used for any other than their intended purposes (e.g. climbing onto or down from the lift truck, portmanteau, etc.).
- If the control components are fitted with a forced operation (lever lock) device, it is forbidden to leave the cab without first putting these controls in neutral.
- It is prohibited to carry passengers either on the lift truck or in the cab.
1 - 8
INTRODUCTION TO SAFETY
C - ENVIRONMENT
- Comply with site safety regulations.
- If you have to use the lift truck in a dark area or at night, make sure it is equipped with working lights.
- During handling operations, make sure that no one is in the way of the lift truck and its load.
- Do not allow anybody to come near the working area of the lift truck or pass beneath an elevated load.
- When using the lift truck on a transverse slope, before lifting the jib, follow the instructions given in the paragraph : INSTRUC-
TIONS FOR HANDLING A LOAD : D - TRANSVERSE ATTITUDE OF THE LIFT TRUCK.
- Travelling on a longitudinal slope :
• Drive and brake gently.
• Moving without load : Forks or attachment facing downhill.
• Moving with load : Forks or attachment facing uphill.
- Take into account the lift truck’s dimensions and its load before trying to negotiate a narrow or low passageway.
- Never move onto a loading platform without having first checked :
• That it is suitably positioned and made fast.
• That the unit to which it is connected (wagon, lorry, etc.) will not shift.
• That this platform is prescribed for the total weight of the lift truck to be loaded.
• That this platform is prescribed for the size of the lift truck.
- Never move onto a foot bridge, floor or freight lift, without being certain that they are prescribed for the weight and size of the lift truck to be loaded and without having checked that they are in sound working order.
- Be careful in the area of loading bays, trenches, scaffolding, soft land and manholes.
- Make sure the ground is stable and firm under the wheels and/or stabilizers before lifting or removing the load. If necessary, add sufficient wedging under the stabilizers.
- Make sure that the scaffolding, loading platform, pilings or ground is capable of bearing the load.
- Never stack loads on uneven ground, they may tip over.
If the load or the attachment must remain above a structure for a long time, there is the risk that it will rest on the structure because of the jib descending owing to the oil in the cylinders cooling down.
To eliminate this risk :
- Regularly check the distance between the load or the attachment and the structure and readjust this if necessary.
- If possible use the lift truck at an oil temperature as close as possible to ambient temperature.
- In the case of work near aerial lines, ensure that the safety distance is sufficient between the working area of the lift truck and the aerial line.
You must consult your local electrical agency. You could be electrocuted or seriously injured if you operate or park the lift truck too close to power cables.
In the event of high winds, do not carry out handling work that jeopardizes the stability of the lift truck and its load, particularly if the load catches the wind badly.
D - VISIBILITY
- Maintain permanently good visibility throughout the route. In reverse, either look directly behind you or use the panoramic rearview mirrors. In any case, avoid reversing over long distances.
- Visibility may be reduced on the right-hand side when the jib is raised, so before lifting the jib make sure that the movement can be made in complete safety.
- If the visibility in forward motion is not sufficient because of the bulkiness of the load, drive in reverse motion. This manoeuvre must remain exceptional and for short distances.
- Ensure you have good visibility (clean windows, adequate lighting, correctly adjusted rear view mirrors, etc.).
- If visibility of your road is inadequate, ask someone to help, standing outside the area in which the truck will be moving, and make sure you always have a good view of this person.
1 - 9
INTRODUCTION TO SAFETY
E - STARTING THE LIFT TRUCK
SAFETY NOTICE
The lift truck must only be started up or manoeuvred when the operator is sitting in the driver’s cab, with his seat belt adjusted and fastened.
- Never try to start the lift truck by pushing or towing it. Such operation may cause severe damage to the transmission. If necessary, to tow the lift truck in an emergency, the transmission must be placed in the neutral position (see : 3 - MAINTENANCE : G
- OCCASIONAL MAINTENANCE).
- If using an emergency battery for start-up, use a battery with the same characteristics and respect battery polarity when connecting it. Connect at first the positive terminals before the negative terminals.
Failure to respect polarity between batteries can cause serious damage to the electrical circuit. The electrolyte in the battery may produce an explosive gas. Avoid flames and generation of sparks close to the batteries. Never disconnect a battery while it is charging.
INSTRUCTIONS
- Check the closing and locking of the hood(s).
- Make sure that the forward/reverse lever is in neutral.
- Turn the ignition key to the position I to activate the electrical system.
- Whenever you switch on the lift truck, perform the automatic check on the longitudinal stability alarm system (see : 2 - DES-
CRIPTION : INSTRUMENTS AND CONTROLS). Do not use the lift truck if it does not conform to the regulations.
- Make sure the signal lights on the instrument control panel and fuel level indicators are working properly (see : 2 - DESCRIP-
TION : INSTRUMENTS AND CONTROLS).
- Turn the ignition key to position II to preheat for 5 seconds and turn the ignition key fully : the I.C. engine should then start.
Release the ignition key and let the I.C. engine run at idle.
- Do not engage the starter motor for more than 15 seconds and carry out the preheating for 5 seconds between unsuccessful attempts.
- Make sure all the signal lights on the control instrument panel are off.
- Check all control instruments when the I.C. engine is warm and at regular intervals during use, so as to quickly detect any faults and to be able to correct them without any delay.
- If an instrument does not show the correct display, stop the I.C. engine and immediately carry out the necessary operations.
F - DRIVING THE LIFT TRUCK
SAFETY NOTICE
Operators' attention is drawn to the risks involved in using the lift truck, in particular :
- Risk of losing control.
- Risk of losing lateral and frontal stability of the lift truck.
The operator must remain in control of the lift truck.
In the event of the lift truck overturning, do not try to leave the cabin during the incident. YOUR BEST PROTECTION IS TO STAY FASTE-
NED IN THE CABIN.
- Observe the company’s traffic regulations or, by default, the public highway code.
- Do not carry out operations which exceed the capacities of your lift truck or attachments.
- Always drive the lift truck with the forks or attachment to the transport position, i.e. at 300 mm from the ground, the jib retracted and the carriage sloping backwards.
- Only carry loads which are balanced and properly anchored to avoid any risk of a load falling off.
- Ensure that palettes, cases, etc, are in good order and suitable for the load to be lifted.
- Familiarise yourself with the lift truck on the terrain where it will be used.
- Ensure that the service brakes are working properly.
- The loaded lift truck must not travel at speeds in excess of 12 km/h.
- Drive smoothly at an appropriate speed for the operating conditions (land configuration, load on the lift truck).
- Do not use the hydraulic jib controls when the lift truck is moving.
- Do not manoeuvre the lift truck with the jib in the raised position unless under exceptional circumstances and then with extreme caution, at very low speed and using gentle braking. Ensure that visibility is adequate.
- Take bends slowly.
- In all circumstances make sure you are in control of your speed.
- On damp, slippery or uneven terrain, drive slowly.
- Brake gently, never abruptly.
- Only use the lift truck’s forward/reverse lever from a stationary position and never do so abruptly.
- Do not drive with your foot on the brake pedal.
- Always remember that hydrostatic type steering is extremely sensitive to movement of the steering wheel, so turn it gently and not jerkily.
- Never leave the I.C. engine on when the lift truck is unattended.
- Do not leave the cab when the lift truck has a raised load.
- Look where you are going and always make sure you have good visibility along the route.
1 - 10
INTRODUCTION TO SAFETY
- Use the rear-view mirrors frequently.
- Drive round obstacles.
- Never drive on the edge of a ditch or steep slope.
- It is dangerous to use two lift trucks simultaneously to handle heavy or voluminous loads, since this operation requires particular precautions to be taken. It must only be used exceptionally and after risk analysis.
- The ignition switch has an emergency stop mechanism in case of an operating anomaly occurring in the case of lift trucks not fitted with a punch-operated cut-out.
INSTRUCTIONS
- Always drive the lift truck with the forks or attachment to the transport position, i.e. at 300 mm from the ground, the jib retracted and the carriage sloping backwards.
- For lift trucks with gearboxes, use the recommended gear (see : 2 - DESCRIPTION : INSTRUMENTS AND CONTROLS).
- Select the steering mode appropriate for its use and/or working conditions (see : 2 - DESCRIPTION : INSTRUMENTS AND
CONTROLS) (as model of lift truck).
- Release the parking brake.
- Shift the forward/reverse lever to the selected direction of travel and accelerate gradually until the lift truck moves off.
G - STOPPING THE LIFT TRUCK
SAFETY NOTICE
- Never leave the ignition key in the lift truck during the operator's absence.
- When the lift truck is stationary, or if the operator has to leave his cab (even for a moment), place the forks or attachment on the ground, apply the parking brake and put the forward/reverse lever in neutral.
- Make sure that the lift truck is not stopped in any position that will interfere with the traffic flow and at less than one meter from the track of a railway.
- In the event of prolonged parking on a site, protect the lift truck from bad weather, particularly from frost (check the level of antifreeze), close and lock all the lift truck accesses (doors, windows, cowls…).
INSTRUCTIONS
- Park the lift truck on flat ground or on an incline lower than 15 %.
- Place the forward/reverse lever in neutral.
- Apply the parking brake.
- For lift trucks with gearboxes, place the gear lever in neutral.
- Retract entirely the jib.
- Lower the forks or attachment to rest on the ground.
- When using an attachment with a grab or jaws, or a bucket with hydraulic opening, close the attachment fully.
- Before stopping the lift truck after a long working period, leave the I.C. engine idling for a few moments, to allow the coolant liquid and oil to lower the temperature of the I.C. engine and transmission. Do not forget this precaution, in the event of frequent stops or warm stalling of the I.C. engine, or else the temperature of certain parts will rise significantly due to the stopping of the cooling system, with the risk of badly damaging such parts.
- Stop the I.C. engine with the ignition switch.
- Remove the ignition key.
- Lock all the accesses to the lift truck (doors, windows, cowls…).
1 - 11
INTRODUCTION TO SAFETY
H - DRIVING THE LIFT TRUCK ON THE PUBLIC HIGHWAY
SAFETY INSTRUCTIONS
- Operators driving on the public highway must comply with current highway code legislation.
- The lift truck must comply with current road legislation. If necessary, there are optional solutions. Contact your dealer.
INSTRUCTIONS
- Make sure the revolving light is in place, switch it on and verify its operation.
- Check the good working order and cleanness of lights, indicators and windscreen wiper.
- Switch off the working headlights if the lift truck is fitted with them.
- Select the steering mode "HIGHWAY TRAFFIC" (as model of lift truck) (see : 2 - DESCRIPTION : INSTRUMENTS AND CONTROLS).
- Retract entirely the jib and put the attachment at 300 mm from the ground.
- Place the slope correctors in the central position, i.e. the transverse shaft of the axles parallel to the chassis (as model of lift truck).
- Lift up the stabilizers to the maximum and turn the blocks inwards (as model of lift truck).
- For lift trucks with gearboxes :
On the road, set off in 3rd gear and go into 4th (as model of lift truck) when the conditions and state of the road allow. In hilly areas, set off in 2nd gear and go into 3rd when the conditions and state of the road allow.
Never move in neutral (gear reverser or gear lever in neutral or transmission cut-off button pressed) to preserve the lift truck engine brake.
Failure to respect this instruction on a slope will lead to excessive speed which may make the lift truck uncontrollable (steering, brakes) and may cause severe mechanical damage.
1 - 12
INTRODUCTION TO SAFETY
DRIVING THE LIFT TRUCK WITH A FRONT-MOUNTED ATTACHMENT
- You must comply with current regulations in your country, covering the possibility of driving on the public highway with a frontmounted attachment on your lift truck.
- If road legislation in your country authorizes circulation with a front-mounted attachment, you must at least :
• Protect and report any sharp and/or dangerous edges on the attachment (see : 4 - ADAPTABLE ATTACHMENTS IN
OPTION ON THE RANGE : ATTACHMENT SHIELDS).
• The attachment must not be loaded.
• Make sure that the attachment does not mask the lighting range of the forward lights.
• Make sure that current legislation in your country does not require other obligations.
OPERATING THE LIFT TRUCK WITH A TRAILER
- For using a trailer, observe the regulations in force in your country (maximum travel speed, braking, maximum weight of trailer, etc.).
- Do not forget to connect the trailer’s electrical equipment to that of the lift truck.
- The trailer's braking system must comply with current legislation.
- If pulling a trailer with assisted braking, the tractor lift truck must be equipped with a trailer braking mechanism. In this case, do not forget to connect the trailer braking equipment to the lift truck.
- The maximum vertical pull on the trailer hook must not exceed 1500 daN.
- The authorised maximum train weight must not exceed the maximum weight authorised by the manufacturer (consult the manufacturer’s plate on your lift truck).
- For lift trucks with gearboxes :
When driving with a trailer, set off in 2nd gear and go into 3rd when the conditions and state of the road allow. Do not exceed
4th gear to avoid overheating the internal combustion engine and the transmission.
IF NECESSARY, CONSULT YOUR DEALER.
1 - 13
INTRODUCTION TO SAFETY
I
NSTRUCTIONS FOR HANDLING A LOAD
A - CHOICE OF ATTACHMENTS
- Only attachments approved by MANITOU can be used on its lift trucks.
- Make sure the attachment is appropriate for the work to be done (see : 4 - ADAPTABLE ATTACHMENTS IN OPTION ON THE RANGE).
- Make sure the attachment is correctly installed and locked onto the lift truck carriage.
- Make sure that your lift truck attachments work properly.
- Comply with the load chart limits for the lift truck for the attachment used.
- Do not exceed the rated capacity of the attachment.
- Never lift a load in a sling without the attachment provided for the purpose. There are optional solutions ; contact your dealer.
B - MASS OF LOAD AND CENTRE OF GRAVITY
- Before taking up a load, you must know its mass and its centre of gravity.
- The load chart for your lift truck is valid for a load in which the longitudinal position of the centre of gravity is 24 in. from the base of the forks (fig. B1). For a higher centre of gravity, contact your dealer.
- For irregular loads, determine the transverse centre of gravity before any movement (fig.
B2) and set it in the longitudinal axis of the lift truck.
It is forbidden to move a load heavier than the effective capacity defined on the lift truck load chart.
For loads with a moving centre of gravity (e.g. liquids), take account of the variations in the centre of gravity in order to determine the load to be handled and be vigilant and take extra care to limit these variations as far as possible.
24 IN.
500 mm
B1
B2
C - N/A
- This device gives an indication of the lift truck's longitudinal stability. Move the jib very carefully when approaching the authorized load limit (see : 2 - DESCRIPTION : INSTRU-
MENTS AND CONTROLS).
- Always watch this device during handling operations.
- When the device is in alert mode, it is forbidden to perform so-called "AGGRAVATING" movements, these being :
A - Extending the jib.
B - Lowering the jib.
- Perform movements to relieve aggravation in the following order (fig. C) : if necessary, raise the jib (1), retract the jib as far as possible (2) and lower the jib (3) to release the load.
The instrument reading may be erroneous when the steering is at its maximum limit or the rear axle oscillated to its limit. Before lifting a load, make sure that the lift truck is not in either of these situations.
C
2
3
1
1 - 14
INTRODUCTION TO SAFETY
D - TRANSVERSE ATTITUDE OF THE LIFT TRUCK
(depending on the model of lift truck)
The transverse attitude is the transverse slope of the chassis with respect to the horizontal.
Raising the jib reduces the lift truck's lateral stability. The transverse attitude must be set with the jib in down position as follows :
1 - LIFT TRUCK WITHOUT SLOPE CORRECTOR USED ON TYRES
- Position the lift truck so that the bubble in the level is between the two lines (see : 2 -
DESCRIPTION : INSTRUMENTS AND CONTROLS).
2 - LIFT TRUCK WITH SLOPE CORRECTOR USED ON TYRES
- Correct the slope using the hydraulic control and verify the horizontality via the level. The bubble in the level must be between the two lines (see : 2 - DESCRIPTION : INSTRU-
MENTS AND CONTROLS).
3 - LIFT TRUCK USED ON STABILIZERS
- Set the two stabilizers on the ground and raise the two front wheels of the lift truck (fig.
D1).
- Correct the slope using the stabilizers (fig. D2) and make sure the truck is horizontal by checking the level. The bubble of the level must be between the two lines (see : 2 - DES-
CRIPTION : INSTRUMENTS AND CONTROLS). In this position, the two front wheels must be off the ground.
E - TAKING UP A LOAD ON THE GROUND
- Approach the lift truck perpendicular to the load, with the jib retracted and the forks in a horizontal position (fig. E1).
- Adjust the fork spread and centering in connection with the load (fig. E2) (optional solutions exist, consult your dealer).
- Never lift a load with a single fork.
Beware of the risks of trapping or squashing limbs when manually adjusting the forks.
- Move the lift truck forward slowly (1) and bring the forks to stop in front of the load (fig.
E3), if necessary, slightly lift the jib (2) while taking up the load.
- Bring the load into the transport position.
- Tilt the load far enough backwards to ensure stability (loss of load on braking or going downhill).
FOR A NON-PALLETIZED LOAD
- Tilt the carriage (1) forwards and move the lift truck slowly forwards (2), to insert the fork under the load (fig. E4) (block the load if necessary).
- Continue to move the lift truck forwards (2) tilting the carriage (3) (fig. E4) backwards to position the load on the forks and check the load's longitudinal and lateral stability.
D1
D2
E1
E2
2
E3
1
E4
3
1
2
1 - 15
INTRODUCTION TO SAFETY
F - TAKING UP AND LAYING A HIGH LOAD ON TYRES
You must not raise the jib if you have not checked the transverse attitude of the lift truck (see :
INSTRUCTIONS FOR HANDLING A LOAD : D - TRANSVERSE ATTITUDE OF THE LIFT TRUCK).
REMINDER : Make sure that the following operations can be performed with good visibility
(see : OPERATIONS INSTRUCTIONS UNLADEN AND LADEN : D - VISIBILITY).
TAKING UP A HIGH LOAD ON TYRES
- Ensure that the forks will easily pass under the load.
- Lift and extend the jib (1) (2) until the forks are level with the load, moving the lift truck
(3) forward if necessary (fig. F1), moving very slowly and carefully.
- Always think about keeping the distance necessary to fit the forks under the load, between the pile and the lift truck (fig. F1) and use the shortest possible length of jib.
- Stop the forks in front of the load by alternately extending and retracting the jib (1) or, if necessary, moving the lift truck forward (2) (fig. F2). Put the handbrake on and set the reverse gear to neutral.
- Slightly lift the load (1) and incline the carriage (2) backwards to stabilize the load (fig.
F3).
- Tilt the load sufficiently backwards to ensure its stability. If the load is too heavy, place the load back from which it was taken.
- If possible lower the load without shifting the lift truck. Lift the jib (1) to release the load, retract (2) and lower the jib (3) to bring the load into the transport position (fig. F4).
- If this is not possible, back up the lift truck (1), manoeuvring very gently and carefully to release the load. Retract (2) and lower the jib (3) to bring the load into the transport position (fig. F5).
2
1
F3
F2
1
2
F1
2
1
3
F4
1
2
3
F5
3
1
2
1 - 16
INTRODUCTION TO SAFETY
LAYING A HIGH LOAD ON TYRES
- Approach the load in the transport position in front of the pile (fig. F6).
- Put the handbrake on and set the reversing lever to neutral.
- Lift and extend the jib (1) (2) until the load is above the pile. If necessary, move the lift truck (3) forward (fig. F7), driving very slowly and carefully.
- Place the load in a horizontal position and lay it down on the pile by lowering and retracting the jib (1) (2) in order to position the load correctly (fig. F8).
- If possible, release the fork by alternately retracting and raising the jib (1) (fig. F9). Then set the forks into transport position.
- If this is not possible, reverse the lift truck (1) very slowly and carefully to release the forks (fig. F10). Then set them into transport position.
F6
1
2
F8
F7
2
1
3
F9
1
F10
1
1 - 17
INTRODUCTION TO SAFETY
G - TAKING UP AND LAYING A HIGH LOAD ON STABILIZERS
(depending on the model of lift truck)
You must not raise the jib if you have not checked the transverse attitude of the lift truck (see : INSTRUCTIONS FOR HANDLING A LOAD :
D - TRANSVERSE ATTITUDE OF THE LIFT TRUCK).
REMINDER : Make sure that the following operations can be performed with good visibility (see : OPERATIONS INSTRUCTIONS
UNLADEN AND LADEN : D - VISIBILITY).
USING THE STABILIZERS
The stabilizers are used to optimise the lift truck's lifting performances (see : 2 - DESCRIPTION : INSTRUMENTS AND CONTROLS).
POSITION THE STABILIZERS WITH THE FORKS IN TRANSPORT POSITION (UNLADEN AND LADEN)
- Set the forks in transport position in front of the elevation.
- Stay far enough away to have room for the jib to be raised.
- Put on the parking brake and set the gear reverser lever to neutral.
- Set the two stabilizers on the ground and lift the two front wheels of the lift truck (fig.
G1), while maintaining its transverse stability.
G1
RAISE THE STABILIZERS WITH THE FORKS IN TRANSPORT POSITION (UNLADEN AND LADEN)
- Raise both stabilizers fully and at the same time.
SETTING THE STABILIZERS WITH THE JIB UP (UNLADEN AND LADEN)
This operation must be exceptional and performed with great care.
- Raise the jib and retract the telescopes completely.
- Set the lift truck in position in front of the elevation (fig. G2) moving very slowly and carefully.
- Put on the parking brake and set the gear reverser lever to neutral.
- Move the stabilizers very slowly and gradually as soon as they are close to the ground or in contact with it.
- Lower the two stabilizers and lift the two front wheels of the lift truck (fig. G3). During this operation, transverse attitude must be permanently maintained : the bubble in the level must be kept between the two lines.
RAISING THE STABILIZERS WITH THE JIB UP (UNLADEN AND LADEN)
This operation must be exceptional and performed with great care.
- Keep the jib up and retract the telescopes completely (fig. G3).
- Move the stabilizers very slowly and gradually as soon as they are in contact with the ground and when they leave the ground. During this operation, the transverse attitude must be permanently maintained : the bubble in the level must be kept between the two lines.
- Raise both stabilizers completely.
- Release the parking brake and reverse the lift truck (1) very slowly and carefully, to release it and lower the forks (2) into transport position (fig. G4).
G2
G3
G4
2
1
1 - 18
INTRODUCTION TO SAFETY
TAKING UP A HIGH LOAD ON STABILIZERS
- Make sure the forks will fit easily under the load.
- Check the position of the lift truck with respect to the load and make a test run, if necessary, without taking the load.
- Raise and extend the jib (1) (2) until the forks are at the level of the load (fig. G5).
- Block the forks in front of the load by alternately using the controls to extend and lower the jib (1) (fig. G6).
- Lift the load slightly (1) and tilt the carriage (2) backwards to stabilise the load (fig. G7).
- If the load is too heavy, set the load down from where it was taken.
- If possible lower the load without moving the lift truck. Raise the jib (1) to release the load, retract (2) and lower the jib (3) to set the load into transport position (fig. G8).
G5
2
1
G6
1
2
1
G7
LAYING A HIGH LOAD ON STABILIZERS
- Raise and extend the jib (1) (2) until the load is above the elevation (fig. G9).
- Position the load horizontally and release it by lowering and retracting the jib (1) (2) to position the load correctly (fig. G10).
- Release the forks by alternating retracting and raising the jib (3) (fig. G11).
- If possible, set the jib in transport position without moving the lift truck.
G9
2
1
G8
1
2
3
1
2
G10 G11
3
1 - 19
INTRODUCTION TO SAFETY
INTRODUCTION TO SAFETY
INTRODUCTION TO SAFETY
MAINTENANCE INSTRUCTIONS OF THE LIFT TRUCK
G
ENERAL INSTRUCTIONS
- Ensure the area is sufficiently ventilated before starting the lift truck.
- Wear clothes suitable for the maintenance of the lift truck, avoid wearing jewellery and loose clothes. Tie and protect your hair, if necessary.
- Stop the I.C. engine and remove the ignition key, when an intervention is necessary.
- Read the operator's manual carefully.
- Carry out all repairs immediately, even if the repairs concerned are minor.
- Repair all leaks immediately, even if the leak concerned is minor.
- Make sure that the disposal of process materials and of spare parts is carried out in total safety and in a ecological way.
- Be careful of the risk of burning and splashing (exhaust, radiator, I.C. engine, etc.).
M
AINTENANCE
- Perform the periodic service (see : 3 - MAINTENANCE) to keep your lift truck in good working conditions. Failure to perform the periodic service may cancel the contractual guarantee.
L
UBRICANT AND FUEL LEVELS
- Use the recommended lubricants (never use contaminated lubricants).
- Do not fill the fuel tank when the I.C. engine is running.
- Only fill up the fuel tank in areas specified for this purpose.
- Do not fill the fuel tank to the maximum level.
- Do not smoke or approach the lift truck with a flame, when the fuel tank is open or is being filled.
H
YDRAULIC
- Any work on the load handling hydraulic circuit is forbidden except for the operations described in part : 3 - MAINTENANCE.
- Do not attempt to loosen unions, hoses or any hydraulic component with the circuit under pressure.
BALANCING VALVE : For inspection, see : 3 – MAINTENANCE : D - EVERY 500 HOURS SERVICE. It is dangerous to change the setting and remove the balancing valves or safety valves which may be fitted to your lift truck cylinders. These operations must only be performed by approved personnel (consult your dealer).
The HYDRAULIC ACCUMULATORS that may be fitted on your lift truck are pressurised units. Removing these accumulators and their pipework is a dangerous operation and must only be performed by approved personnel (consult your dealer).
E
LECTRICITY
- Do not short-circuit the starter relay to start the IC engine. If the gear reverser is not in neutral and the parking brake is not engaged, the lift truck may suddenly start to move.
- Do not drop metallic items on the battery.
- Disconnect the battery before working on the electrical circuit.
1 - 22
INTRODUCTION TO SAFETY
W
ELDING
- Disconnect the battery before any welding operations on the lift truck.
- When carrying out electric welding work on the lift truck, connect the negative cable from the equipment directly to the part being welded, so as to avoid high tension current passing through the alternator.
- Never carry out welding or work which gives off heat on an assembled tyre. The heat would increase the pressure which could cause the tyre to explode.
- If the lift truck is equipped with an electronic control unit, disconnect this before starting to weld, to avoid the risk of causing irreparable damage to electronic components.
W
ASHING THE LIFT TRUCK
- Clean the lift truck or at least the area concerned before any intervention.
- Remember to close and lock all accesses to the lift truck (doors, windows, cowls…).
- During washing, avoid the articulations and electrical components and connections.
- If necessary, protect against penetration of water, steam or cleaning agents, components susceptible of being damaged, particularly electrical components and connections and the injection pump.
- Clean the lift truck of any fuel, oil or grease trace.
FOR ANY INTERVENTION OTHER THAN REGULAR MAINTENANCE, CONSULT YOUR DEALER.
1 - 23
INTRODUCTION TO SAFETY
IF THE LIFT TRUCK IS NOT TO BE USED FOR A LONG TIME
I
NTRODUCTION
The following recommendations are intended to prevent the lift truck from being damaged when it is withdrawn from service for an extended period.
For these operations, we recommend the use of a protective product. Contact your dealer.
Instructions for using the product are given on the packaging.
Procedures to follow if the lift truck is not to be used for a long time and for starting it up again afterwards must be performed by your dealership.
P
REPARING THE LIFT TRUCK
- Clean the lift truck thoroughly.
- Check and repair any leakage of fuel, oil, water or air.
- Replace or repair any worn or damaged parts.
- Wash the painted surfaces of the lift truck in clear and cold water and wipe them.
- Touch up the paintwork if necessary.
- Shut down the lift truck (see : OPERATING INSTRUCTIONS UNLADEN AND LADEN).
- Make sure the jib cylinder rods are all in retracted position.
- Release the pressure in the hydraulic circuits.
P
ROTECTING THE
I.C.
ENGINE
- Fill the tank with fuel (see : 3 - MAINTENANCE : A - DAILY OR EVERY 10 HOURS SERVICE).
- Empty and replace the cooling liquid (see : 3 - MAINTENANCE : F - EVERY 2000 HOURS SERVICE).
- Leave the I.C. engine running at idling speed for a few minutes, then switch off.
- Replace the I.C. engine oil and oil filter (see : 3 - MAINTENANCE : D - EVERY 500 HOURS SERVICE).
- Add the protective product to the engine oil.
- Run the I.C. engine for a short time so that the oil and cooling liquid circulate inside.
- Disconnect the battery and store it in a safe place away from the cold, after charging it to a maximum.
- Remove the injectors and spray the protective product into each cylinder for two seconds with the piston in low neutral position.
- Turn the crankshaft once slowly and refit the injectors (see I.C. engine REPAIR MANUAL).
- Remove the intake hose from the manifold or turbocharger and spray the protective product into the manifold or turbocharger.
- Cap the intake manifold or turbocharger hole with waterproof adhesive tape.
- Remove the exhaust pipe and spray the protective product into the exhaust manifold or turbocharger.
- Refit the exhaust pipe and block the outlet with waterproof adhesive tape.
NOTE : The spray time is noted on the product packaging and must be increased by 50 % for turbo engines.
- Open the filler plug, spray the protective product around the rocker arm shaft and refit the filler plug.
- Cap the fuel tank using waterproof adhesive tape.
- Remove the drive belts and store them in a safe place.
- Disconnect the engine cut-off solenoid on the injection pump and carefully insulate the connection.
P
ROTECTING THE LIFT TRUCK
- Set the lift truck on axle stands so that the tyres are not in contact with the ground and release the handbrake.
- Protect cylinder rods which will not be retracted, from corrosion.
- Wrap the tyres.
NOTE : If the lift truck is to be stored outdoors, cover it with a waterproof tarpaulin.
1 - 24
INTRODUCTION TO SAFETY
B
RINGING THE LIFT TRUCK BACK INTO SERVICE
- Remove the waterproof adhesive tape from all the holes.
- Refit the intake hose.
- Refit and reconnect the battery.
- Remove the protection from the cylinder rods.
- Perform the daily service (see : 3 - MAINTENANCE : A - DAILY OR EVERY 10 HOURS SERVICE).
- Put the handbrake on and remove the axle stands.
- Empty and replace the fuel and replace the fuel filter (see : 3 - MAINTENANCE : D - EVERY 500 HOURS SERVICE).
- Refit and set the tension in the drive belts (see : 3 - MAINTENANCE : C - EVERY 250 HOURS SERVICE).
- Turn the I.C. engine using the starter, to allow the oil pressure to rise.
- Reconnect the engine cut-off solenoid.
- Lubricate the lift truck completely (see : 3 - MAINTENANCE : SERVICING SCHEDULE).
Make sure the area is adequately ventilated before starting up the lift truck.
- Start up the lift truck, following the safety instructions and regulations (see : OPERATING INSTRUCTIONS UNLADEN AND LADEN).
- Run all the jib's hydraulic movements, concentrating on the ends of travel for each cylinder.
1 - 25
INTRODUCTION TO SAFETY
1 - 26
INTRODUCTION TO SAFETY
2 - 1
INTRODUCTION TO SAFETY
2 - 2
INTRODUCTION TO SAFETY
MT 1233 S Série 2
2 - 3
INTRODUCTION TO SAFETY
IDENTIFICATION OF THE LIFT TRUCK
As our policy is to promote a constant improvement of our products, our range of telescopic lift trucks may undergo certain modifications, without obligation for us to advise our customers.
When you order parts, or when you require any technical information, always specify :
NOTE : For the owner's convenience, it is recommended that a note of these numbers is made in the spaces provided, at the time of the delivery of the lift truck.
P
LATE MANUFACTURER OF THE LIFT TRUCK
(F
IG
. A)
- Model
- Series
- Serial Nr
- Chassis Nr
- Year of manufacture
For any further technical information regarding your lift truck refer to chapter :
CHARACTERISTICS in paragraph : 2 - DESCRIPTION.
I.C.
ENGINE
(F
IG
. B)
- Engine Nr
T
RANSMISSION
(F
IG
. C)
- Type
- MANITOU reference
- Serial Nr
A
NGLE GEAR
-
BOX
(F
IG
. D)
- Type
- MANITOU reference
- Serial Nr
A
B
C
D
2 - 4
INTRODUCTION TO SAFETY
F
RONT AXLE
(F
IG
. E)
- Type
- Serial Nr
- MANITOU reference
R
EAR AXLE
(F
IG
. F)
- Type
- Serial Nr
- MANITOU reference
C
AB
(F
IG
. G)
- Type
- Serial Nr
J
IB
(F
IG
. H)
- MANITOU reference
- Date of manufacture
P
LATE MANUFACTURER OF THE ATTACHMENT
(F
IG
. I)
- Model
- Serial Nr
- Year of manufacture
H
2 - 5
E
F
G
I
INTRODUCTION TO SAFETY
CHARACTERISTICS
E
NGINE
- Type MT 845 Série 2
MT 845 Turbo Série 2 + Turbo MONO-ULTRA
MT 940 L Série 2
MT 940 L Turbo Série 2 + Turbo MONO-ULTRA
MT 1233 S Série 2
MT 1233 S Turbo Série 2 + Turbo MONO-ULTRA
MT 1240 L Série 2
MT 1240 L Turbo Série 2 + Turbo MONO-ULTRA
MT 1330 SL Série 2
MT 1330 SL Turbo Série 2
MT 1337 SL Série 2
MT 1337 SL Turbo Série 2 + Turbo MONO-ULTRA
MT 1637 SL Série 2
MT 1637 SL Turbo Série 2 + Turbo MONO-ULTRA
MT 1740 SL Série 2
MT 1740 SL Turbo Série 2
- Number of cylinders
- Number of strokes
- Suction
- Injection system
- Ignition sequence
- Clearance of rocker valve (Cold)
. Inlet
. Exhaust
- Capacity
- Bore
- Stroke
- Compression ratio
- Nominal rating loaded
- Rating slow unladen
- Max. rating unladen
- Power ISO/TR 14396
- Maximum torque ISO/TR 14396
- Air cleaner
C
OOLING CIRCUIT
- Type
- Fan
. Number of blades
. Diameter
- Thermostat
. Start opening
. Full opening
T
RANSMISSION
- Type
- Torque converter
- Gear box
. Number of forward speeds
. Number of reverse speeds
- Gear reverser
PERKINS 1004.42 AR 81026 or AR 81334
PERKINS 1004.40T AK 80920 or AK 81298 or AK 81336
PERKINS 1004.42 AR 81026 or AR 81334
PERKINS 1004.40T AK 80920 or AK 81298 or AK 81336
PERKINS 1004.42 AR 81026 or AR 81334
PERKINS 1004.40T AK 80920 or AK 81298 or AK 81336
PERKINS 1004.42 AR 81026 or AR 81334
PERKINS 1004.40T AK 80920 or AK 81298 or AK 81336
PERKINS 1004.42 AR 81026 or AR 81334
PERKINS 1004.40T AK 80920 or AK 81298 or AK 81336
PERKINS 1004.42 AR 81026 or AR 81334
PERKINS 1004.40T AK 80920 or AK 81298 or AK 81336
PERKINS 1004.42 AR 81026 or AR 81334
PERKINS 1004.40T AK 80920 or AK 81298 or AK 81336
PERKINS 1004.42 AR 81334
PERKINS 1004.40T AK 81336
1004.42 AR 81026
1004.42 AR 81334
4 in line
4
Natural
Direct
1.3.4.2.
0,20 mm
0,45 mm
4233 cm3
103 mm
127 mm
18.5 / 1
2200 rpm
930 rpm
+20
- 0
2350 rpm
81,5 cv / 60 kw
290 Nm at 1400 rpm
Dry 3 µ
1004.40T AK 80920
4 in line
4
Compressed turbo
Direct
1.3.4.2.
1004.40T AK 81298
1004.40T AK 81336
4 in line
4
Compressed turbo
Direct
1.3.4.2.
0,20 mm
0,45 mm
3990 cm3
100 mm
127 mm
17.25 / 1
2200 rpm
930 rpm
+20
- 0
2400 rpm
0,20 mm
0,45 mm
3990 cm3
100 mm
127 mm
17.25 / 1
2200 rpm
930 rpm
+20
- 0
2400 rpm
104 cv / 76,5 kw 100 cv / 74,6 kw
394 Nm at 1400 rpm 402,6 Nm at 1400 rpm
Dry 3 µ Dry 3 µ
By water
Puller
10
508 mm
77 °C to 85 °C
92 °C to 98 °C
TURNER POWERTRAIN SYSTEMS
SACHS
4
4
Electro-hydraulic
2 - 6
INTRODUCTION TO SAFETY
A
NGLE GEAR
-
BOX
- Type
F
RONT AXLE
- Type
- Hub reducers
R
EAR AXLE
- Type
- Hub reducers
B
RAKE
- Service brake
. Type
- Parking brake
. Type
E
LECTRIC CIRCUIT
- Earth
- Battery
- Alternator
. Type
. Tension regulator
- Starter
. Type
TURNER POWERTRAIN SYSTEMS
DANA
Epicyclic
DANA
Epicyclic
Foot pedal. Hydraulic servo-brake, applied on the front and rear wheels.
Multidisc brake immersed in oil.
Mechanical hand lever applied on the front wheels.
Multidisc brake immersed in oil.
Negative
12 V - 105 Ah - 680 A EN
12 V - 65 A
Magneti Marelli A127
Incorporated into the alternator
12 V
Magneti Marelli M127
2 - 7
INTRODUCTION TO SAFETY
CHARACTERISTICS
MT 845 Série 2
MT 845 Turbo Série 2
MT 845 Turbo MONO-ULTRA Série 2
F
RONT AND REAR TYRES
STANDARD
OPTION
OPTION
OPTION
DIMENSIONS
445/70R24 IT510 151G
GOODYEAR
440/80-24 T37 158B
DUNLOP
18x19,5 16PR T35 STAB. TL
DUNLOP
15,5x25 12PR SGL DL 2A
GOODYEAR
15,5/80-24 SGI TL 16PR
GOODYEAR
445/70R24 XM47 TL 151G
MICHELIN
1200R24 X MINE D2
MICHELIN
15,5R25 XHA
MICHELIN
445/65R22,5 XZY TL 168K
MICHELIN
18R19,5 XF TL
MICHELIN
4,1 Bar
5 Bar
4,5 Bar
4,5 Bar
4,1 Bar
6 Bar
4 Bar
4,5 Bar
6,5 Bar
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
PRESSURE
4,1 Bar
Front unladen
Front laden
Rear unladen
Rear laden
TYRE LOAD PRESSURE ON THE CONTACT SURFACE AREA OF THE CONTACT SURFACE
HARD GROUND LIGHT GROUND HARD GROUND LIGHT GROUND
1600 kg 8,4 kg/cm2
5700 kg 10,3 kg/cm2
2550 kg 9,1 kg/cm2
700 kg 7 kg/cm2
2,8 kg/cm2
3,4 kg/cm2
3 kg/cm2
2,3 kg/cm2
190 cm2
555 cm2
280 cm2
100 cm2
570 cm2
1680 cm2
840 cm2
305 cm2
1600 kg 7,3 kg/cm2
5700 kg 12 kg/cm2
2550 kg 8,4 kg/cm2
700 kg 5,7 kg/cm2
1600 kg 6,4 kg/cm2
5700 kg 10,1 kg/cm2
2550 kg 7,5 kg/cm2
700 kg 4,8 kg/cm2
1600 kg 7,3 kg/cm2
5700 kg 8,4 kg/cm2
2550 kg 6,9 kg/cm2
700 kg 5 kg/cm2
1600 kg 8,4 kg/cm2
5700 kg 13,7 kg/cm2
2550 kg 10,2 kg/cm2
700 kg 8,8 kg/cm2
1600 kg 1,7 kg/cm2
5700 kg 3,3 kg/cm2
2550 kg 2,3 kg/cm2
700 kg 1 kg/cm2
1600 kg 3,6 kg/cm2
5700 kg 6,6 kg/cm2
2550 kg 4,7 kg/cm2
700 kg 2 kg/cm2
1600 kg 2,6 kg/cm2 1,22 kg/cm2
5700 kg 3,6 kg/cm2 1,64 kg/cm2
2550 kg 3,1 kg/cm2 1,44 kg/cm2
700 kg 1,6 kg/cm2 0,74 kg/cm2
1600 kg 3,2 kg/cm2
5700 kg 4,8 kg/cm2
2550 kg 3,7 kg/cm2
700 kg 2,4 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2
1600 kg 3,4 kg/cm2 1,58 kg/cm2
5700 kg 4,2 kg/cm2 1,94 kg/cm2
2550 kg 3,7 kg/cm2 1,7 kg/cm2
700 kg 3,2 kg/cm2 1,48 kg/cm2
2 kg/cm2
3,3 kg/cm2
2,3 kg/cm2
1,6 kg/cm2
2,7 kg/cm2
4,2 kg/cm2
3,2 kg/cm2
2,1 kg/cm2
3,9 kg/cm2
4,5 kg/cm2
3,8 kg/cm2
2,7 kg/cm2
2,3 kg/cm2
3,7 kg/cm2
2,8 kg/cm2
2,3 kg/cm2
220 cm2
475 cm2
305 cm2
122 cm2
249 cm2
563 cm2
351 cm2
145 cm2
220 cm2
680 cm2
370 cm2
140 cm2
190 cm2
415 cm2
250 cm2
80 cm2
960 cm2
1730 cm2
1150 cm2
760 cm2
442 cm2
859 cm2
538 cm2
350 cm2
610 cm2
1576 cm2
827 cm2
445 cm2
498 cm2
1185 cm2
687 cm2
287 cm2
470 cm2
1362 cm2
695 cm2
220 cm2
800 cm2
1720 cm2
1100 cm2
440 cm2
591 cm2
1343 cm2
835 cm2
341 cm2
410 cm2
1260 cm2
680 cm2
260 cm2
690 cm2
1530 cm2
920 cm2
300 cm2
1307 cm2
3486 cm2
1774 cm2
951 cm2 cm2 cm2 cm2 cm2 cm2 cm2 cm2 cm2 cm2 cm2 cm2 cm2
1014 cm2
2939 cm2
1500 cm2
474 cm2
H
YDRAULIC CIRCUIT
- Type of pump
. Capacity
- Lifting, tilting, telescoping, attachment circuit
. Max. rating capacity unladen
. Pressure
- Steering circuit
. Max. rating capacity unladen
. Pressure
- Braking circuit
. Max. rating capacity unladen
. Pressure
- Filtration
. Return
. Suction
Gear pump with flow divider
41 cm3
98 L/mn
250 Bar
98 L/mn
140 Bar
98 L/mn
40 Bar
10 µ
100 µ
2 - 8
INTRODUCTION TO SAFETY
S
PECIFICATIONS
- Level of sound pressure in the driver's cab LpA
(According to standard prEN 12053 : 1995)
- Level of sound power in the LwA environment
(According to directive 2000 / 14 CE guaranteed)
MT 845 Série 2
MT 845 Turbo Série 2 + T M-U
- Travel speed of the lift truck
(Except particular conditions)
. Forward
. Reverse
- Standard lift height
- Rated capacity with standard attachment
- Load center
- Weight of forks (Each)
- Lifting motions (Jib retracted)
. Unladen lifting
. Laden lifting
. Unladen lowering
. Laden lowering
- Telescoping motions (Lifting jib)
. Unladen extending
. Laden extending
. Unladen retracting
. Laden retracting
- Reverse tilt time unladen
- Forward tilt time unladen
- Lift truck weight with standard attachment
. Unladen
. Rated load
- Axle weight with attached equipment (Transport position)
. Front unladen
Rated load
. Rear unladen
Rated load
- Tensible strain at coupling hook
. Unladen
. Rated load
MT 845 Série 2
MT 845 Turbo Série 2 + T M-U
- Break out force with bucket
(According to standard ISO 8313)
2 - 9
83,6 dB
105 dB
106 dB
8300 kg
12800 kg
3220 kg
11430 kg
5080 kg
1370 kg
6600 daN
7500 daN
9000 daN
6650 daN
10,5 s
11 s
7,2 s
6,7 s
11,6 s
11,6 s
6,5 s
6 s
4,6 s
3,7 s
27,6 km/h
27,6 km/h
7550 mm
4500 kg
500 mm
72 kg
27,5 m/mn
26,3 m/mn
40,2 m/mn
43,2 m/mn
16,3 m/mn
16,3 m/mn
29,1 m/mn
31,5 m/mn
30,8 °/s
38,3 °/s
INTRODUCTION TO SAFETY
DIMENSIONS AND LOAD CHART
MT 845 Série 2
MT 845 Turbo Série 2
MT 845 Turbo MONO-ULTRA Série 2
9
40°
7.55
8
7
30°
6
5
20°
4
3
10°
2
1
0°
-4.5°
0
-1
6
Lift truck "INDUSTRIAL VERSION"
(According to standard en 1459 annexe A)
50°
MT 845
59°
0.5m
5 4
4.57
4.12
3 2
3.29 2.33 1.55
2.75
1 0m
2.02
1.80 1.45
SUIVANT NORME EN 1459 annexe A.
2 - 10
Lift truck "ALL TERRAIN VERSION"
(According to standard en 1459 annexe B)
MT 845
50° 59°
9
40°
7.55
8
7
30° 6
5
20°
4
3
10°
2
0°
-3°
1
0
-1
6
2000KG
5
4.57
4
4.12
3 2
3.29 2.33 1.55
2.75
2.02
1
1.45
0m
0.5m
SUIVANT NORME EN 1459 annexe B.
INTRODUCTION TO SAFETY
MT 845 Série 2
O
P2
P3
R
L
N
J
K
G1
G2
I
F
F1
G
D1
D2
E
A
B
C
C1
D
S
T
U1
U2
V
V1
V2
W
1200 mm
2770 mm
1395 mm
1315 mm
5215 mm
5135 mm
4395 mm
6415 mm
1950 mm
1950 mm
450 mm
425 mm
450 mm
1050 mm
950 mm
1040 mm
50 mm
1870 mm
125 mm
43,5 °
40 °
3900 mm ***
4030 mm ****
8045 mm ***
8230 mm ****
4255 mm
2550 mm
2690 mm *
2730 mm **
5260 mm ***
5410 mm ****
1425 mm ***
1575 mm ****
4100 mm ***
4250 mm ****
2410 mm ***
2395 mm ****
12 °
130 °
Y
Z
* : 1 st ASSEMBLY
** : 2 nd ASSEMBLY
*** : Up to machine Nr : 147615
**** : From machine Nr : 147616
MT 845 Turbo Série 2
1200 mm
2770 mm
1395 mm
1315 mm
5215 mm
5135 mm
4395 mm
6415 mm
1950 mm
1950 mm
450 mm
425 mm
450 mm
1050 mm
950 mm
1040 mm
50 mm
1870 mm
125 mm
43,5 °
40 °
3900 mm ***
4030 mm ****
8045 mm ***
8230 mm ****
4255 mm
2550 mm
2690 mm *
2730 mm **
5260 mm ***
5410 mm ****
1425 mm ***
1575 mm ****
4100 mm ***
4250 mm ****
2410 mm ***
2395 mm ****
12 °
130 °
MT 845 Turbo
MONO-ULTRA Série 2
1200 mm
2770 mm
1395 mm
1315 mm
5215 mm
5135 mm
4395 mm
6415 mm
1950 mm
1950 mm
450 mm
425 mm
450 mm
1050 mm
950 mm
1040 mm
50 mm
1880 to 1930 mm
125 mm
43,5 °
40 °
3900 mm ***
4030 mm ****
8045 mm ***
8230 mm ****
4255 mm
2550 mm
2690 mm *
2730 mm **
5260 mm ***
5410 mm ****
1425 mm ***
1575 mm ****
4100 mm ***
4250 mm ****
2410 mm ***
2395 mm ****
12 °
130 °
2 - 11
INTRODUCTION TO SAFETY
CHARACTERISTICS
MT 940 L TW (120) LS Series 2
F
RONT AND REAR TYRES
DIMENSIONS PRESSURE
STANDARD
15,5/80-24 SGI TL 16PR
GOODYEAR
4,5 Bar
Front unladen
Front laden
Rear unladen
Rear laden
OPTION
440/80-24 T37 158B
DUNLOP
400/80-24 T37 156B
DUNLOP
4,5 Bar
4,75 Bar
18x19,5 16PR T35 STAB. TL 5 Bar
DUNLOP
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
OPTION
15,5x25 12PR SGL DL 2A
GOODYEAR
445/70R24 IT510 151G
GOODYEAR
4,5 Bar
4,1 Bar
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
OPTION
445/70R24 XM47 TL 151G
MICHELIN
1200R24 X MINE D2
MICHELIN
15,5R25 XHA
MICHELIN
18R19,5 XF TL
MICHELIN
4,1 Bar
6,5 Bar
4 Bar
6,5 Bar
OPTION
480/65R24 TL 146D SF
NOKIAN
3,8 Bar
Front unladen
Front laden
Rear unladen
Rear laden
H
YDRAULIC CIRCUIT
- Type of pump
. Capacity
- Lifting, tilting, telescoping, tilting corrector, attachment circuit
. Max. rating capacity unladen
. Pressure
- Steering circuit
. Max. rating capacity unladen
. Pressure
- Braking circuit
. Max. rating capacity unladen
. Pressure
- Filtration
. Return
. Suction
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
TYRE LOAD PRESSURE ON THE CONTACT SURFACE AREA OF THE CONTACT SURFACE
HARD GROUND LIGHT GROUND HARD GROUND LIGHT GROUND
1750 kg 8,7 kg/cm2
5750 kg 13,8 kg/cm2
2500 kg 10,4 kg/cm2
550 kg 8,8 kg/cm2
2,4 kg/cm2
3,7 kg/cm2
2,7 kg/cm2
2,4 kg/cm2
201 cm2
417 cm2
240 cm2
62,5 cm2
740 cm2
1544 cm2
915 cm2
230 cm2
1750 kg 7,6 kg/cm2
5750 kg 12,4 kg/cm2
2500 kg 8,5 kg/cm2
550 kg 5,5 kg/cm2
1750 kg 8,5 kg/cm2
5750 kg 13,5 kg/cm2
2500 kg 9,6 kg/cm2
550 kg 6,3 kg/cm2
1750 kg 6,6 kg/cm2
5750 kg 10,1 kg/cm2
2500 kg 7,3 kg/cm2
550 kg 4,3 kg/cm2
1750 kg 7,1 kg/cm2
5750 kg 8,4 kg/cm2
2500 kg 6,9 kg/cm2
550 kg 3,9 kg/cm2
1750 kg 8,5 kg/cm2
5750 kg 10,3 kg/cm2
2500 kg 9,1 kg/cm2
550 kg 6,1 kg/cm2
3,9 kg/cm2
4,5 kg/cm2
3,8 kg/cm2
2,1 kg/cm2
2,8 kg/cm2
3,4 kg/cm2
3 kg/cm2
2,1 kg/cm2
1750 kg 1,8 kg/cm2
5750 kg 3,3 kg/cm2
2500 kg 2,2 kg/cm2
550 kg 0,8 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2
1750 kg 3,9 kg/cm2
5750 kg 6,8 kg/cm2
2500 kg 4,8 kg/cm2
550 kg 1,6 kg/cm2
0,9 kg/cm2
2,4 kg/cm2
1,2 kg/cm2
0,3 kg/cm2
1750 kg 2,7 kg/cm2 1,28 kg/cm2
5750 kg 3,6 kg/cm2 1,64 kg/cm2
2500 kg 3,1 kg/cm2 1,44 kg/cm2
550 kg 1,3 kg/cm2 0,62 kg/cm2
1750 kg 3,3 kg/cm2 1,54 kg/cm2
5750 kg 4,2 kg/cm2 1,95 kg/cm2
2500 kg 3,7 kg/cm2 1,69 kg/cm2
550 kg 2,8 kg/cm2 1,28 kg/cm2
1750 kg 3,1 kg/cm2
5750 kg 3,3 kg/cm2
2500 kg 3,3 kg/cm2
550 kg 2,9 kg/cm2
2,1 kg/cm2
3,4 kg/cm2
2,3 kg/cm2
1,5 kg/cm2
2,4 kg/cm2
3,8 kg/cm2
2,7 kg/cm2
1,7 kg/cm2
2,8 kg/cm2
4,2 kg/cm2
3,1 kg/cm2
1,9 kg/cm2
0,9 kg/cm2
2 kg/cm2
1,2 kg/cm2
0,3 kg/cm2
Gear pump with flow divider
41 cm3
98 L/mn
250 Bar
98 L/mn
140 Bar
98 L/mn
40 Bar
10 µ
100 µ
246 cm2
685 cm2
360 cm2
140 cm2
205 cm2
559 cm2
275 cm2
90 cm2
990 cm2
1740 cm2
1140 cm2
722 cm2
453 cm2
844 cm2
526 cm2
335 cm2
638 cm2
1588 cm2
810 cm2
416 cm2
526 cm2
1369 cm2
684 cm2
200 cm2
230 cm2
465 cm2
295 cm2
100 cm2
205 cm2
425 cm2
260 cm2
88 cm2
264 cm2
570 cm2
342 cm2
127 cm2
556 cm2
1731 cm2
768 cm2
192 cm2
450 cm2
1270 cm2
665 cm2
260 cm2
620 cm2
1700 cm2
830 cm2
260 cm2 cm2 cm2 cm2 cm2
1948 cm2
2394 cm2
2042 cm2
1779 cm2
1367 cm2
3512 cm2
1736 cm2
892 cm2
1135 cm2
2952 cm2
1477 cm2
431 cm2
830 cm2
1690 cm2
1070 cm2
360 cm2
740 cm2
1510 cm2
940 cm2
315 cm2
631 cm2
1361 cm2
813 cm2
297 cm2
1980 cm2
2920 cm2
2180 cm2
1600 cm2
2 - 12
INTRODUCTION TO SAFETY
S
PECIFICATIONS
- Level of sound pressure in the driver's cab LpA
(According to standard prEN 12053 : 1995)
- Level of sound power in the LwA environment
(According to directive 2000 / 14 CE guaranteed)
MT 940 L Série 2
MT 940 L Turbo Série 2 + T M-U
- Travel speed of the lift truck
(Except particular conditions)
. Forward
. Reverse
- Standard lift height
- Rated capacity with standard attachment
- Load center
- Weight of forks (Each)
- Lifting motions (Jib retracted)
. Unladen lifting
. Laden lifting
. Unladen lowering
. Laden lowering
- Telescoping motions (Lifting jib)
. Unladen extending
. Laden extending
. Unladen retracting
. Laden retracting
- Reverse tilt time unladen
- Forward tilt time unladen
- Lift truck weight with standard attachment
. Unladen
. Rated load
- Axle weight with attached equipment (Transport position)
. Front unladen
Rated load
. Rear unladen
Rated load
- Tensible strain at coupling hook
. Unladen
. Rated load
MT 940 L Série 2
MT 940 L Turbo Série 2 + T M-U
- Break out force with bucket
(According to standard ISO 8313)
2 - 13
83,6 dB
105 dB
106 dB
8595 kg
12595 kg
3545 kg
11485 kg
5050 kg
1110 kg
6100 daN
7500 daN
8600 daN
7000 daN
12 s
12,5 s
8,5 s
8 s
13 s
13 s
7,2 s
6,7 s
4,6 s
3,7 s
27,6 km/h
27,6 km/h
8970 mm
4000 kg
500 mm
72 kg
28,7 m/mn
27,1 m/mn
40,3 m/mn
42,9 m/mn
16,3 m/mn
16,3 m/mn
29,1 m/mn
31,5 m/mn
30,8 °/s
38,3 °/s
INTRODUCTION TO SAFETY
DIMENSIONS AND LOAD CHART
MT 940 L TW (120) LS Series 2
MT 940 L
60° 70° 50°
10
8.97
9
40°
8
7
3500KG
30°
6
5
20°
4
3
10°
2
1
0°
-3°
0
-1
6
5.32
5
4.32
4 3 2
3.48
2.47
2.89
2.12
1.82
1
SUIVANT NORME EN 1459 annexe B.
0m
0.5m
2 - 14
INTRODUCTION TO SAFETY
MT 940 L Série 2
D1
D2
E
F
A
B
C
C1
D
O
P2
P3
L
N
J
K
R
G
G1
G2
H
H1
I
F1
S
T
U1
U2
V
V1
V2
W
1200 mm
2770 mm
1820 mm
1740 mm
5640 mm
5560 mm
4420 mm
6840 mm
1970 mm ***
1990 mm ****
1970 mm ***
1990 mm ****
450 mm
445 mm
450 mm
10 °
10 °
1050 mm
950 mm
1040 mm
50 mm
1850 mm
125 mm
43,5 °
40 °
3640 mm ***
3950 mm ****
8380 mm ***
8555 mm ****
4385 mm
2575 mm
2715 mm *
2755 mm **
5320 mm ***
5470 mm ****
1320 mm ***
1470 mm ****
4000 mm ***
4150 mm ****
2370 mm ***
2390 mm ****
12 °
130 °
Y
Z
* : 1 st ASSEMBLY
** : 2 nd ASSEMBLY
*** : Up to machine Nr : 147615
**** : From machine Nr : 147616
MT 940 L Turbo Série 2
1200 mm
2770 mm
1820 mm
1740 mm
5640 mm
5560 mm
4420 mm
6840 mm
1970 mm ***
1990 mm ****
1970 mm ***
1990 mm ****
450 mm
445 mm
450 mm
10 °
10 °
1050 mm
950 mm
1040 mm
50 mm
1850 mm
125 mm
43,5 °
40 °
3640 mm ***
3950 mm ****
8380 mm ***
8555 mm ****
4385 mm
2575 mm
2715 mm *
2755 mm **
5320 mm ***
5470 mm ****
1320 mm ***
1470 mm ****
4000 mm ***
4150 mm ****
2370 mm ***
2390 mm ****
12 °
130 °
MT 940 L Turbo
MONO-ULTRA Série 2
1200 mm
2770 mm
1820 mm
1740 mm
5640 mm
5560 mm
4420 mm
6840 mm
1970 mm ***
1990 mm ****
1970 mm ***
1990 mm ****
450 mm
445 mm
450 mm
10 °
10 °
1050 mm
950 mm
1040 mm
50 mm
1860 to 1910 mm
125 mm
43,5 °
40 °
3640 mm ***
3950 mm ****
8380 mm ***
8555 mm ****
4385 mm
2575 mm
2715 mm *
2755 mm **
5320 mm ***
5470 mm ****
1320 mm ***
1470 mm ****
4000 mm ***
4150 mm ****
2370 mm ***
2390 mm ****
12 °
130 °
2 - 15
INTRODUCTION TO SAFETY
CHARACTERISTICS
MT 1233 S Série 2
MT 1233 S Turbo Série 2
MT 1233 S Turbo MONO-ULTRA Série 2
F
RONT AND REAR TYRES
STANDARD
OPTION
OPTION
OPTION
OPTION
DIMENSIONS
15,5/80-24 SGI TL 12PR
GOODYEAR
18-19.5 16PR I224 TL
ALLIANCE
440/80-24 T37 158B
DUNLOP
15,5x25 12PR SGL DL 2A
GOODYEAR
445/70R24 XM47 TL 151G
MICHELIN
1200R24 X MINE D2
MICHELIN
15,5R25 XHA
MICHELIN
18R19,5 XF TL
MICHELIN
PRESSURE
4,5 Bar
Front unladen
Front laden
Rear unladen
Rear laden
5,5 Bar
Front unladen
Front laden
Rear unladen
Rear laden
4,5 Bar
Front unladen
Front laden
Rear unladen
Rear laden
4,5 Bar
Front unladen
Front laden
Rear unladen
Rear laden
TYRE LOAD PRESSURE ON THE CONTACT SURFACE AREA OF THE CONTACT SURFACE
HARD GROUND LIGHT GROUND HARD GROUND LIGHT GROUND
2250 kg 9,6 kg/cm2
5550 kg 13,7 kg/cm2
2250 kg 9,6 kg/cm2
550 kg 9,2 kg/cm2
2,5 kg/cm2
3,7 kg/cm2
2,5 kg/cm2
2,6 kg/cm2
2250 kg 4,21 kg/cm2 1,79 kg/cm2
5550 kg 7,05 kg/cm2 3,00 kg/cm2
2250 kg 4,21 kg/cm2 1,79 kg/cm2
550 kg 1,90 kg/cm2 0,80 kg/cm2
2250 kg 8,2 kg/cm2
5550 kg 12,1 kg/cm2
2250 kg 8,2 kg/cm2
550 kg 5,5 kg/cm2
2,3 kg/cm2
3,3 kg/cm2
2,3 kg/cm2
1,5 kg/cm2
235 cm2
405 cm2
235 cm2
60 cm2
534 cm2
787 cm2
534 cm2
289 cm2
275 cm2
460 cm2
275 cm2
100 cm2
890 cm2
1500 cm2
890 cm2
210 cm2
1260 cm2
1847 cm2
1260 cm2
686 cm2
990 cm2
1670 cm2
990 cm2
360 cm2
4,1 Bar
6 Bar
4 Bar
6,5 Bar
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
2250 kg 6,8 kg/cm2
5550 kg 8,3 kg/cm2
2250 kg 6,8 kg/cm2
550 kg 3,9 kg/cm2
3,7 kg/cm2
4,5 kg/cm2
3,7 kg/cm2
2,1 kg/cm2
2250 kg 2 kg/cm2
5550 kg 3,3 kg/cm2
2250 kg 2 kg/cm2
550 kg 0,8 kg/cm2
2250 kg 4,4 kg/cm2
5550 kg 6,6 kg/cm2
2250 kg 4,4 kg/cm2
550 kg 1,6 kg/cm2
2250 kg 3,1 kg/cm2 1,44 kg/cm2
5550 kg 3,6 kg/cm2 1,63 kg/cm2
2250 kg 3,1 kg/cm2 1,44 kg/cm2
550 kg 1,3 kg/cm2 0,62 kg/cm2
2250 kg 3,6 kg/cm2 1,65 kg/cm2
5550 kg 4,2 kg/cm2 1,94 kg/cm2
2250 kg 3,6 kg/cm2 1,65 kg/cm2
550 kg 2,8 kg/cm2 1,28 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2
330 cm2
670 cm2
330 cm2
140 cm2
1100 cm2
1701 cm2
1100 cm2
722 cm2
508 cm2
843 cm2
508 cm2
335 cm2
731 cm2
1541 cm2
731 cm2
416 cm2
632 cm2
1325 cm2
632 cm2
200 cm2
610 cm2
1240 cm2
610 cm2
260 cm2
1565 cm2
3405 cm2
1565 cm2
892 cm2
1363 cm2
2858 cm2
1363 cm2
431 cm2 cm2 cm2 cm2 cm2 cm2 cm2 cm2 cm2
H
YDRAULIC CIRCUIT
- Type of pump
- Lifting, tilting, telescoping, stabilizer, attachment circuit
. Max. rating capacity unladen
. Pressure
. Capacity
- Steering circuit
. Max. rating capacity unladen
. Pressure
. Capacity
- Braking circuit
. Max. rating capacity unladen
. Pressure
. Capacity
- Filtration
. Return
. 2nd body suction
Gear double pump with flow divider
1st body 2nd body
98 L/mn
260 Bar
41 cm3
68 L/mn
160 Bar
28,5 cm3
2nd body
68 L/mn
140 Bar
28,5 cm3
2nd body
68 L/mn
40 Bar
28,5 cm3
10 µ
100 µ
2 - 16
INTRODUCTION TO SAFETY
S
PECIFICATIONS
- Level of sound pressure in the driver's cab LpA
(According to standard prEN 12053 : 1995)
- Level of sound power in the LwA environment
(According to directive 2000 / 14 CE guaranteed)
MT 1233 S Série 2
MT 1233 S Turbo Série 2 + T M-U
- Travel speed of the lift truck
(Except particular conditions)
. Forward
. Reverse
- Standard lift height
- Rated capacity with standard attachment
- Load center
- Weight of forks (Each)
- Lifting motions (Jib retracted)
. Unladen lifting
. Laden lifting
. Unladen lowering
. Laden lowering
- Telescoping motions (Lifting jib)
. Unladen extending
. Laden extending
. Unladen retracting
. Laden retracting
- Reverse tilt time unladen
- Forward tilt time unladen
- Lift truck weight with standard attachment
. Unladen
. Rated load
- Axle weight with attached equipment (Transport position)
. Front unladen
Rated load
. Rear unladen
Rated load
- Tensible strain at coupling hook
. Unladen
. Rated load
MT 1233 S Série 2
MT 1233 S Turbo Série 2 + T M-U
- Break out force with bucket
(According to standard ISO 8313)
2 - 17
83,6 dB
105 dB
106 dB
8960 kg
12260 kg
4510 kg
11105 kg
4450 kg
1155 kg
6100 daN
7500 daN
8600 daN
7000 daN
12 s
12,5 s
8,5 s
8 s
15,4 s
15,4 s
12,7 s
12,2 s
4,75 s
4,2 s
27,6 km/h
27,6 km/h
12000 mm
3300 kg
500 mm
68 kg
28,2 m/mn
26,7 m/mn
39,7 m/mn
42,2 m/mn
25,9 m/mn
25,9 m/mn
31,5 m/mn
32,6 m/mn
26,1 °/s
29,5 °/s
INTRODUCTION TO SAFETY
DIMENSIONS AND LOAD CHART
MT 1233 S Série 2
MT 1233 S Turbo Série 2
MT 1233 S Turbo MONO-ULTRA Série 2
MT 1233 S
60° 66° 50°
30°
8
7
6
20°
5
4
10°
3
2
13
12
11.64
40° 11
10
9
200KG
1
0°
0
-5.5°
-1
9 8
8.39
7.65
7 6
6.1
5
4.53
5.05
4 3 2 1
3.55
2.85
2.35 1.83
SUIVANT NORME EN 1459 annexe B.
0m
0.5m
2 - 18
MT 1233 S
60° 70° 70.5° 50°
40° 11
10
9
13
12
30°
8
7
6
20°
5
4
10°
3
2
1
0°
0
-5.5°
-1
9
8.32
8 7
6.75
6
5.6
5
4.8
4 3 2
1.78
1
SUIVANT NORME EN 1459 annexe B.
0.5m
0m
INTRODUCTION TO SAFETY
MT 1233 S Série 2
D1
D2
E
F
A
B
C
C1
D
P2
P3
R
K
L
N
O
G
G1
G2
G3
I
J
F1
S
T
U1
U2
V
V1
V2
W
W1
W2
W3
Y
Z
1200 mm
2770 mm
1770 mm
1695 mm
5590 mm
5515 mm
4420 mm
6790 mm
1970 mm ***
1990 mm ****
1970 mm ***
1990 mm ****
450 mm
445 mm
450 mm
275 mm
1050 mm
950 mm
1040 mm
45 mm
1850 mm
125 mm
43,5 °
40 °
3640 mm ***
3950 mm ****
8365 mm ***
8505 mm ****
4365 mm
2575 mm
2715 mm *
2755 mm **
5300 mm ***
5450 mm ****
1320 mm ***
1470 mm ****
4000 mm ***
4150 mm ****
2370 mm ***
2390 mm ****
2320 mm
1225 mm
2035 mm
12 °
112 °
* : 1 st ASSEMBLY
** : 2 nd ASSEMBLY
*** : Up to machine Nr : 147615
**** : From machine Nr : 147616
MT 1233 S Turbo Série 2
1200 mm
2770 mm
1770 mm
1695 mm
5590 mm
5515 mm
4420 mm
6790 mm
1970 mm ***
1990 mm ****
1970 mm ***
1990 mm ****
450 mm
445 mm
450 mm
275 mm
1050 mm
950 mm
1040 mm
45 mm
1850 mm
125 mm
43,5 °
40 °
3640 mm ***
3950 mm ****
8365 mm ***
8505 mm ****
4365 mm
2575 mm
2715 mm *
2755 mm **
5300 mm ***
5450 mm ****
1320 mm ***
1470 mm ****
4000 mm ***
4150 mm ****
2370 mm ***
2390 mm ****
2320 mm
1225 mm
2035 mm
12 °
112 °
MT 1233 S Turbo
MONO-ULTRA Série 2
1200 mm
2770 mm
1770 mm
1695 mm
5590 mm
5515 mm
4420 mm
6790 mm
1970 mm ***
1990 mm ****
1970 mm ***
1990 mm ****
450 mm
445 mm
450 mm
275 mm
1050 mm
950 mm
1040 mm
45 mm
1860 to 1910 mm
125 mm
43,5 °
40 °
3640 mm ***
3950 mm ****
8365 mm ***
8505 mm ****
4365 mm
2575 mm
2715 mm *
2755 mm **
5300 mm ***
5450 mm ****
1320 mm ***
1470 mm ****
4000 mm ***
4150 mm ****
2370 mm ***
2390 mm ****
2320 mm
1225 mm
2035 mm
12 °
112 °
2 - 19
INTRODUCTION TO SAFETY
CHARACTERISTICS
MT 1240 L Série 2
MT 1240 L Turbo Série 2
MT 1240 L Turbo MONO-ULTRA Série 2
F
RONT AND REAR TYRES
STANDARD
OPTION
OPTION
OPTION
DIMENSIONS
15,5/80-24 SGI TL 16PR
GOODYEAR
440/80-24 T37 158B
DUNLOP
400/80-24 T37 156B
DUNLOP
15,5x25 12PR SGL DL 2A
GOODYEAR
445/70R24 IT510 151G
GOODYEAR
445/70R24 XM47 TL 151G
MICHELIN
1200R24 X MINE D2
MICHELIN
15,5R25 XHA
MICHELIN
18R19,5 XF TL
MICHELIN
PRESSURE
4,5 Bar
Front unladen
Front laden
Rear unladen
Rear laden
TYRE LOAD PRESSURE ON THE CONTACT SURFACE AREA OF THE CONTACT SURFACE
HARD GROUND LIGHT GROUND HARD GROUND LIGHT GROUND
2250 kg 9,6 kg/cm2
6100 kg 14 kg/cm2
2500 kg 10,4 kg/cm2
700 kg 8,8 kg/cm2
2,6 kg/cm2
3,8 kg/cm2
2,7 kg/cm2
2,3 kg/cm2
235 cm2
435 cm2
240 cm2
80 cm2
855 cm2
1610 cm2
915 cm2
300 cm2
4,5 Bar
4,75 Bar
4,5 Bar
4,1 Bar
4,1 Bar
6,5 Bar
4 Bar
6,5 Bar
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
2250 kg 8,2 kg/cm2
6100 kg 12,7 kg/cm2
2500 kg 8,5 kg/cm2
700 kg 5,8 kg/cm2
2250 kg 9,4 kg/cm2
6100 kg 13,9 kg/cm2
2500 kg 9,6 kg/cm2
700 kg 6,6 kg/cm2
2250 kg 6,8 kg/cm2
6100 kg 8,5 kg/cm2
2500 kg 6,9 kg/cm2
700 kg 5 kg/cm2
2250 kg 9 kg/cm2
6100 kg 10,3 kg/cm2
2500 kg 9,1 kg/cm2
700 kg 7 kg/cm2
2250 kg 2 kg/cm2
6100 kg 3,4 kg/cm2
2500 kg 2,2 kg/cm2
700 kg 1 kg/cm2
2250 kg 4,5 kg/cm2
6100 kg 6,9 kg/cm2
2500 kg 4,8 kg/cm2
700 kg 2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2
1,1 kg/cm2
2,5 kg/cm2
1,2 kg/cm2
0,4 kg/cm2
2250 kg 3,1 kg/cm2 1,44 kg/cm2
6100 kg 3,7 kg/cm2 1,65 kg/cm2
2500 kg 3,1 kg/cm2 1,44 kg/cm2
700 kg 1,6 kg/cm2 0,74 kg/cm2
2250 kg 3,6 kg/cm2 1,65 kg/cm2
6100 kg 4,3 kg/cm2 2 kg/cm2
2500 kg 3,7 kg/cm2 1,69 kg/cm2
700 kg 3,2 kg/cm2 1,48 kg/cm2
2,3 kg/cm2
3,5 kg/cm2
2,3 kg/cm2
1,6 kg/cm2
2,6 kg/cm2
3,9 kg/cm2
2,7 kg/cm2
1,8 kg/cm2
3,7 kg/cm2
4,6 kg/cm2
3,8 kg/cm2
2,7 kg/cm2
3 kg/cm2
3,4 kg/cm2
3 kg/cm2
2,3 kg/cm2
275 cm2
480 cm2
295 cm2
120 cm2
240 cm2
440 cm2
260 cm2
106 cm2
330 cm2
720 cm2
360 cm2
140 cm2
250 cm2
590 cm2
275 cm2
100 cm2
1100 cm2
1800 cm2
1140 cm2
760 cm2
501 cm2
879 cm2
526 cm2
350 cm2
731 cm2
1671 cm2
810 cm2
445 cm2
632 cm2
1412 cm2
684 cm2
220 cm2
990 cm2
1750 cm2
1070 cm2
430 cm2
870 cm2
1570 cm2
940 cm2
380 cm2
610 cm2
1330 cm2
665 cm2
260 cm2
760 cm2
1790 cm2
830 cm2
305 cm2 cm2 cm2 cm2 cm2
2018 cm2
2432 cm2
2042 cm2
1800 cm2
1565 cm2
3701 cm2
1736 cm2
951 cm2
1363 cm2
3047 cm2
1477 cm2
474 cm2
H
YDRAULIC CIRCUIT
- Type of pump
- Lifting, tilting, telescoping, tilting corrector, attachment circuit
. Max. rating capacity unladen
. Pressure
. Capacity
- Steering circuit
. Max. rating capacity unladen
. Pressure
. Capacity
- Braking circuit
. Max. rating capacity unladen
. Pressure
. Capacity
- Filtration
. Return
. 2nd body suction
Gear double pump with flow divider
1st body 2nd body
98 L/mn
260 Bar
41 cm3
68 L/mn
160 Bar
28,5 cm3
2nd body
68 L/mn
140 Bar
28,5 cm3
2nd body
68 L/mn
40 Bar
28,5 cm3
10 µ
100 µ
2 - 20
INTRODUCTION TO SAFETY
S
PECIFICATIONS
- Level of sound pressure in the driver's cab LpA
(According to standard prEN 12053 : 1995)
- Level of sound power in the LwA environment
(According to directive 2000 / 14 CE guaranteed)
MT 1240 L Série 2
MT 1240 L Turbo Série 2 + T M-U
- Travel speed of the lift truck
(Except particular conditions)
. Forward
. Reverse
- Standard lift height
- Rated capacity with standard attachment
- Load center
- Weight of forks (Each)
- Lifting motions (Jib retracted)
. Unladen lifting
. Laden lifting
. Unladen lowering
. Laden lowering
- Telescoping motions (Lifting jib)
. Unladen extending
. Laden extending
. Unladen retracting
. Laden retracting
- Reverse tilt time unladen
- Forward tilt time unladen
- Lift truck weight with standard attachment
. Unladen
. Rated load
- Axle weight with attached equipment (Transport position)
. Front unladen
Rated load
. Rear unladen
Rated load
- Tensible strain at coupling hook
. Unladen
. Rated load
MT 1240 L Série 2
MT 1240 L Turbo Série 2 + T M-U
- Break out force with bucket
(According to standard ISO 8313)
2 - 21
83,6 dB
105 dB
106 dB
9470 kg
13470 kg
4480 kg
12150 kg
4990 kg
1320 kg
6100 daN
7500 daN
8600 daN
7000 daN
12 s
12,5 s
8,5 s
8 s
15,4 s
15,4 s
12,7 s
12,2 s
4,75 s
4,2 s
27,6 km/h
27,6 km/h
11640 mm
4000 kg
500 mm
72 kg
28,2 m/mn
26,7 m/mn
39,7 m/mn
42,2 m/mn
25,9 m/mn
25,9 m/mn
31,5 m/mn
32,6 m/mn
26,1 °/s
29,5 °/s
INTRODUCTION TO SAFETY
DIMENSIONS AND LOAD CHART
MT 1240 L Série 2
MT 1240 L Turbo Série 2
MT 1240 L Turbo MONO-ULTRA Série 2
MT 1240 L
60° 66°
13
11.64
12
40°
11
10
9
30°
8
7
6
20° 5
4
10°
3
2
50°
1
0°
0
-5°
-1
9
8.46
8 7
6.75
6 5
5.2
4
4.15
3.4
3
2.44
2.83
2
1.9
2.12
1
1.86
SUIVANT NORME EN 1459 annexe B.
0m
0.5m
2 - 22
INTRODUCTION TO SAFETY
MT 1240 L Série 2
D1
D2
E
F
A
B
C
C1
D
O
P2
P3
L
N
J
K
R
G
G1
G2
H
H1
I
F1
S
T
U1
U2
V
V1
V2
W
1200 mm
2770 mm
1785 mm
1695 mm
5605 mm
5515 mm
4420 mm
6805 mm
1970 mm ***
1990 mm ****
1970 mm ***
1990 mm ****
450 mm
445 mm
450 mm
10 °
10 °
1050 mm
950 mm
1040 mm
50 mm
1850 mm
125 mm
43,5 °
40 °
3640 mm ***
3950 mm ****
8380 mm ***
8520 mm ****
4385 mm
2575 mm
2715 mm *
2755 mm **
5320 mm ***
5470 mm ****
1320 mm ***
1470 mm ****
4000 mm ***
4150 mm ****
2370 mm ***
2390 mm ****
12 °
112 °
Y
Z
* : 1 st ASSEMBLY
** : 2 nd ASSEMBLY
*** : Up to machine Nr : 147615
**** : From machine Nr : 147616
MT 1240 L Turbo Série 2
1200 mm
2770 mm
1785 mm
1695 mm
5605 mm
5515 mm
4420 mm
6805 mm
1970 mm ***
1990 mm ****
1970 mm ***
1990 mm ****
450 mm
445 mm
450 mm
10 °
10 °
1050 mm
950 mm
1040 mm
50 mm
1850 mm
125 mm
43,5 °
40 °
3640 mm ***
3950 mm ****
8380 mm ***
8520 mm ****
4385 mm
2575 mm
2715 mm *
2755 mm **
5320 mm ***
5470 mm ****
1320 mm ***
1470 mm ****
4000 mm ***
4150 mm ****
2370 mm ***
2390 mm ****
12 °
112 °
MT 1240 L Turbo
MONO-ULTRA Série 2
1200 mm
2770 mm
1785 mm
1695 mm
5605 mm
5515 mm
4420 mm
6805 mm
1970 mm ***
1990 mm ****
1970 mm ***
1990 mm ****
450 mm
445 mm
450 mm
10 °
10 °
1050 mm
950 mm
1040 mm
50 mm
1860 to 1910 mm
125 mm
43,5 °
40 °
3640 mm ***
3950 mm ****
8380 mm ***
8520 mm ****
4385 mm
2575 mm
2715 mm *
2755 mm **
5320 mm ***
5470 mm ****
1320 mm ***
1470 mm ****
4000 mm ***
4150 mm ****
2370 mm ***
2390 mm ****
12 °
112 °
2 - 23
INTRODUCTION TO SAFETY
CHARACTERISTICS
MT 1330 SL Série 2
MT 1330 SL Turbo Série 2
F
RONT AND REAR TYRES
STANDARD
OPTION
OPTION
OPTION
OPTION
DIMENSIONS
15,5/80-24 SGI TL 12PR
GOODYEAR
18-19.5 16PR I224 TL
ALLIANCE
PRESSURE
4,5 Bar
Front unladen
Front laden
Rear unladen
Rear laden
5,5 Bar
Front unladen
Front laden
Rear unladen
Rear laden
440/80-24 T37 158B
DUNLOP
18x19,5 16PR T35 STAB. TL
DUNLOP
15,5x25 12PR SGL DL 2A
GOODYEAR
445/70R24 IT510 151G
GOODYEAR
1200R24 X MINE D2
MICHELIN
15,5R25 XHA
MICHELIN
18R19,5 XF TL
MICHELIN
4,5 Bar
5 Bar
4,5 Bar
4,1 Bar
6 Bar
4 Bar
6,5 Bar
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
TYRE LOAD PRESSURE ON THE CONTACT SURFACE AREA OF THE CONTACT SURFACE
HARD GROUND LIGHT GROUND HARD GROUND LIGHT GROUND
2450 kg 9,8 kg/cm2
5700 kg 13,9 kg/cm2
2200 kg 9,4 kg/cm2
450 kg 12,9 kg/cm2
2,6 kg/cm2
3,7 kg/cm2
2,5 kg/cm2
3,5 kg/cm2
2450 kg 4,42 kg/cm2 1,88 kg/cm2
5700 kg 7,16 kg/cm2 3,05 kg/cm2
2200 kg 4,16 kg/cm2 1,76 kg/cm2
450 kg 1,68 kg/cm2 0,71 kg/cm2
2450 kg 8,4 kg/cm2
5700 kg 12,2 kg/cm2
2200 kg 8,1 kg/cm2
450 kg 5,2 kg/cm2
2450 kg 7,4 kg/cm2
5700 kg 10,1 kg/cm2
2200 kg 7,1 kg/cm2
450 kg 3,9 kg/cm2
2,4 kg/cm2
3,4 kg/cm2
2,3 kg/cm2
1,5 kg/cm2
3,1 kg/cm2
4,2 kg/cm2
3 kg/cm2
1,7 kg/cm2
2450 kg 6,8 kg/cm2
5700 kg 8,4 kg/cm2
2200 kg 6,7 kg/cm2
450 kg 3,2 kg/cm2
2450 kg 9,1 kg/cm2
5700 kg 10,3 kg/cm2
2200 kg 8,8 kg/cm2
450 kg 5,6 kg/cm2
3,7 kg/cm2
4,5 kg/cm2
3,7 kg/cm2
1,7 kg/cm2
3 kg/cm2
3,4 kg/cm2
2,9 kg/cm2
2 kg/cm2
2450 kg 4,6 kg/cm2
5700 kg 6,6 kg/cm2
2200 kg 4,4 kg/cm2
450 kg 1,4 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2
2450 kg 3,1 kg/cm2 1,44 kg/cm2
5700 kg 3,6 kg/cm2 1,64 kg/cm2
2200 kg 3,1 kg/cm2 1,42 kg/cm2
450 kg 1,1 kg/cm2 0,53 kg/cm2
2450 kg 3,6 kg/cm2 1,69 kg/cm2
5700 kg 4,2 kg/cm2 1,94 kg/cm2
2200 kg 3,5 kg/cm2 1,64 kg/cm2
450 kg 2,5 kg/cm2 1,16 kg/cm2
250 cm2
410 cm2
235 cm2
35 cm2
554 cm2
796 cm2
529 cm2
268 cm2
290 cm2
465 cm2
270 cm2
86 cm2
333 cm2
563 cm2
309 cm2
115 cm2
360 cm2
680 cm2
330 cm2
140 cm2
270 cm2
555 cm2
250 cm2
80 cm2
528 cm2
859 cm2
503 cm2
325 cm2
792 cm2
1576 cm2
721 cm2
398 cm2
674 cm2
1362 cm2
621 cm2
180 cm2
930 cm2
1520 cm2
870 cm2
130 cm2
1306 cm2
1868 cm2
1248 cm2
637 cm2
1040 cm2
1680 cm2
970 cm2
310 cm2
791 cm2
1343 cm2
733 cm2
268 cm2
660 cm2
1260 cm2
605 cm2
260 cm2
810 cm2
1680 cm2
755 cm2
230 cm2 cm2 cm2 cm2 cm2
1699 cm2
3486 cm2
1545 cm2
852 cm2
1454 cm2
2939 cm2
1340 cm2
388 cm2
H
YDRAULIC CIRCUIT
- Type of pump
- Lifting, tilting, telescoping, tilting corrector, stabilizer, attachment circuit
. Max. rating capacity unladen
. Pressure
. Capacity
- Steering circuit
. Max. rating capacity unladen
. Pressure
. Capacity
- Braking circuit
. Max. rating capacity unladen
. Pressure
. Capacity
- Filtration
. Return
. 2nd body suction
Gear double pump with flow divider
1st body
98 L/mn
260 Bar
41 cm3
10 µ
100 µ
2nd body
68 L/mn
160 Bar
28,5 cm3
2nd body
68 L/mn
140 Bar
28,5 cm3
2nd body
68 L/mn
40 Bar
28,5 cm3
2 - 24
INTRODUCTION TO SAFETY
S
PECIFICATIONS
- Level of sound pressure in the driver's cab LpA
(According to standard prEN 12053 : 1995)
- Level of sound power in the LwA environment
(According to directive 2000 / 14 CE guaranteed)
MT 1330 SL Série 2
MT 1330 SL Turbo Série 2
- Travel speed of the lift truck
(Except particular conditions)
. Forward
. Reverse
- Standard lift height
- Rated capacity with standard attachment
- Load center
- Weight of forks (Each)
- Lifting motions (Jib retracted)
. Unladen lifting
. Laden lifting
. Unladen lowering
. Laden lowering
- Telescoping motions (Lifting jib)
. Unladen extending
. Laden extending
. Unladen retracting
. Laden retracting
- Reverse tilt time unladen
- Forward tilt time unladen
- Lift truck weight with standard attachment
. Unladen
. Rated load
- Axle weight with attached equipment (Transport position)
. Front unladen
Rated load
. Rear unladen
Rated load
- Tensible strain at coupling hook
. Unladen
. Rated load
MT 1330 SL Série 2
MT 1330 SL Turbo Série 2
- Break out force with bucket
(According to standard ISO 8313)
2 - 25
83,6 dB
105 dB
106 dB
9265 kg
12265 kg
4920 kg
11385 kg
4345 kg
880 kg
6100 daN
7500 daN
8600 daN
7000 daN
11,8 s
12,3 s
8,4 s
7,9 s
17 s
17 s
14 s
13,5 s
4,75 s
4,2 s
27,6 km/h
27,6 km/h
13000 mm
3000 kg
500 mm
68 kg
29,8 m/mn
28,4 m/mn
42,1 m/mn
44,3 m/mn
25,9 m/mn
25,9 m/mn
31,5 m/mn
32,6 m/mn
26,1 °/s
29,5 °/s
INTRODUCTION TO SAFETY
DIMENSIONS AND LOAD CHART
MT 1330 SL Série 2
MT 1330 SL Turbo Série 2
MT 1330 SL
50° 60° 65°
14
12.68
40°
13
12
11
10
30°
9
8
7
20°
6
5
4
10° 3
2
1
0°
0
-6.5°
-1
10 9
9.46
8
7.80
7
6.80
6 5
4.50
4
3.60
3
2.20
2.56
2
SUIVANT NORME EN 1459 annexe B.
1
0.5m
0m
2 - 26
MT 1330 SL
60° 68.5° 50°
14
13
40°
12
11
10
30°
9
8
7
20°
6
5
4
10°
3
2
1
0°
0
-5.5°
-1
10
9.34
9
8.60
8
7.35
7 6
5.55
5
6.35
4.5
4 3 2
2.15
SUIVANT NORME EN 1459 annexe B.
1 0m
0.5m
INTRODUCTION TO SAFETY
C1
D
D1
A
B
C
D2
E
F
K
L
N
H1
I
J
G
G1
G2
G3
H
O
P2
P3
R
F1
S
T
U1
U2
V
V1
V2
W
W1
W2
W3
Y
Z
MT 1330 SL Série 2
1200 mm
2770 mm
2135 mm
2045 mm
5955 mm
5865 mm
4420 mm
7155 mm
1970 mm ***
1990 mm ****
1970 mm ***
1990 mm ****
450 mm
445 mm
450 mm
275 mm
4 °
4 °
1050 mm
950 mm
1040 mm
45 mm
1850 mm
125 mm
45,5 °
40 °
3640 mm ***
3950 mm ****
8720 mm ***
8870 mm ****
4665 mm
2575 mm
2715 mm *
2755 mm **
5600 mm ***
5750 mm ****
1320 mm ***
1470 mm ****
4000 mm ***
4150 mm ****
2370 mm ***
2390 mm ****
2320 mm
1225 mm
2035 mm
12 °
112 °
* : 1 st ASSEMBLY
** : 2 nd ASSEMBLY
*** : Up to machine Nr : 147615
**** : From machine Nr : 147616
2 - 27
MT 1330 SL Turbo Série 2
1200 mm
2770 mm
2135 mm
2045 mm
5955 mm
5865 mm
4420 mm
7155 mm
1970 mm ***
1990 mm ****
1970 mm ***
1990 mm ****
450 mm
445 mm
450 mm
275 mm
4 °
4 °
1050 mm
950 mm
1040 mm
45 mm
1850 mm
125 mm
45,5 °
40 °
3640 mm ***
3950 mm ****
8720 mm ***
8870 mm ****
4665 mm
2575 mm
2715 mm *
2755 mm **
5600 mm ***
5750 mm ****
1320 mm ***
1470 mm ****
4000 mm ***
4150 mm ****
2370 mm ***
2390 mm ****
2320 mm
1225 mm
2035 mm
12 °
112 °
INTRODUCTION TO SAFETY
CHARACTERISTICS
MT 1337 SL Série 2
MT 1337 SL Turbo Série 2
MT 1337 SL Turbo MONO-ULTRA Série 2
F
RONT AND REAR TYRES
STANDARD
OPTION
OPTION
OPTION
OPTION
DIMENSIONS
440/80-24 T37 158B
DUNLOP
PRESSURE
4,5 Bar
Front unladen
Front laden
Rear unladen
Rear laden
15,5R25 L2 1* VKT Tub fire 5,6 Bar
BRIDGESTONE
Front unladen
Front laden
Rear unladen
Rear laden
400/80-24 T37 156B
DUNLOP
18x19,5 16PR T35 STAB. TL
DUNLOP
4,75 Bar
5 Bar
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
15,5x25 12PR SGL DL 2A
GOODYEAR
15,5/80-24 SGI TL 16PR
GOODYEAR
445/70R24 XM47 TL 151G
MICHELIN
1200R24 X MINE D2
MICHELIN
15,5R25 XHA
MICHELIN
18R19,5 XF TL
MICHELIN
4,5 Bar
4,5 Bar
4,1 Bar
6,5 Bar
4 Bar
6,5 Bar
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
TYRE LOAD PRESSURE ON THE CONTACT SURFACE AREA OF THE CONTACT SURFACE
HARD GROUND LIGHT GROUND HARD GROUND LIGHT GROUND
2350 kg 8,4 kg/cm2
6300 kg 12,8 kg/cm2
3050 kg 9 kg/cm2
950 kg 6,3 kg/cm2
2350 kg 8,1 kg/cm2
6300 kg 10,2 kg/cm2
3050 kg 8,4 kg/cm2
950 kg 6,6 kg/cm2
2,3 kg/cm2
3,5 kg/cm2
2,5 kg/cm2
1,8 kg/cm2
3,7 kg/cm2
5 kg/cm2
3,9 kg/cm2
2,7 kg/cm2
2350 kg 9,4 kg/cm2
6300 kg 14,1 kg/cm2
3050 kg 10,2 kg/cm2
950 kg 7,1 kg/cm2
2350 kg 7,3 kg/cm2
6300 kg 9,6 kg/cm2
3050 kg 7,9 kg/cm2
950 kg 5,2 kg/cm2
2,6 kg/cm2
3,9 kg/cm2
2,8 kg/cm2
2 kg/cm2
3,1 kg/cm2
4 kg/cm2
3,3 kg/cm2
2,2 kg/cm2
2350 kg 6,8 kg/cm2
6300 kg 8,5 kg/cm2
3050 kg 7,1 kg/cm2
950 kg 6,8 kg/cm2
2350 kg 9,8 kg/cm2
6300 kg 14,2 kg/cm2
3050 kg 11,1 kg/cm2
950 kg 7,3 kg/cm2
3,7 kg/cm2
4,6 kg/cm2
3,9 kg/cm2
3,7 kg/cm2
2,7 kg/cm2
3,8 kg/cm2
3 kg/cm2
2 kg/cm2
2350 kg 2,1 kg/cm2
6300 kg 3,4 kg/cm2
3050 kg 2,4 kg/cm2
950 kg 1,2 kg/cm2
2350 kg 4,6 kg/cm2
6300 kg 7 kg/cm2
3050 kg 5,3 kg/cm2
950 kg 2,5 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2
1,2 kg/cm2
2,6 kg/cm2
1,5 kg/cm2
0,5 kg/cm2
2350 kg 3,1 kg/cm2 1,45 kg/cm2
6300 kg 3,7 kg/cm2 1,66 kg/cm2
3050 kg 3,2 kg/cm2 1,48 kg/cm2
950 kg 1,9 kg/cm2 0,9 kg/cm2
2350 kg 3,6 kg/cm2 1,67 kg/cm2
6300 kg 4,4 kg/cm2 2,03 kg/cm2
3050 kg 3,8 kg/cm2 1,77 kg/cm2
950 kg 3,7 kg/cm2 1,69 kg/cm2
280 cm2
490 cm2
340 cm2
150 cm2
290 cm2
619 cm2
364 cm2
144 cm2
250 cm2
445 cm2
300 cm2
134 cm2
321 cm2
653 cm2
387 cm2
182 cm2
345 cm2
740 cm2
430 cm2
140 cm2
240 cm2
445 cm2
275 cm2
130 cm2
1120 cm2
1830 cm2
1260 cm2
820 cm2
511 cm2
899 cm2
580 cm2
374 cm2
757 cm2
1719 cm2
951 cm2
490 cm2
653 cm2
1437 cm2
801 cm2
260 cm2
1010 cm2
1780 cm2
1220 cm2
540 cm2
640 cm2
1260 cm2
777 cm2
352 cm2
900 cm2
1600 cm2
1080 cm2
480 cm2
762 cm2
1560 cm2
922 cm2
428 cm2
635 cm2
1365 cm2
790 cm2
260 cm2
880 cm2
1640 cm2
1015 cm2
470 cm2 cm2 cm2 cm2 cm2
2029 cm2
2454 cm2
2099 cm2
1835 cm2
1623 cm2
3809 cm2
2055 cm2
1050 cm2
1409 cm2
3101 cm2
1728 cm2
561 cm2
H
YDRAULIC CIRCUIT
- Type of pump
- Lifting, tilting, telescoping, tilting corrector, stabilizer, attachment circuit
. Max. rating capacity unladen
. Pressure
. Capacity
- Steering circuit
. Max. rating capacity unladen
. Pressure
. Capacity
- Braking circuit
. Max. rating capacity unladen
. Pressure
. Capacity
- Filtration
. Return
. 2nd body suction
2 - 28
Gear double pump with flow divider
1st body
98 L/mn
260 Bar
41 cm3
10 µ
100 µ
2nd body
68 L/mn
160 Bar
28,5 cm3
2nd body
68 L/mn
140 Bar
28,5 cm3
2nd body
68 L/mn
40 Bar
28,5 cm3
INTRODUCTION TO SAFETY
S
PECIFICATIONS
- Level of sound pressure in the driver's cab LpA
(According to standard prEN 12053 : 1995)
- Level of sound power in the LwA environment
(According to directive 2000 / 14 CE guaranteed)
MT 1337 SL Série 2
MT 1337 SL Turbo Série 2 + T M-U
- Travel speed of the lift truck
(Except particular conditions)
. Forward
. Reverse
- Standard lift height
- Rated capacity with standard attachment
- Load center
- Weight of forks (Each)
- Lifting motions (Jib retracted)
. Unladen lifting
. Laden lifting
. Unladen lowering
. Laden lowering
- Telescoping motions (Lifting jib)
. Unladen extending
. Laden extending
. Unladen retracting
. Laden retracting
- Reverse tilt time unladen
- Forward tilt time unladen
- Lift truck weight with standard attachment
. Unladen
. Rated load
- Axle weight with attached equipment (Transport position)
. Front unladen
Rated load
. Rear unladen
Rated load
- Tensible strain at coupling hook
. Unladen
. Rated load
MT 1337 SL Série 2
MT 1337 SL Turbo Série 2 + T M-U
- Break out force with bucket
(According to standard ISO 8313)
2 - 29
83,6 dB
105 dB
106 dB
10790 kg
14490 kg
4720 kg
12580 kg
6070 kg
1910 kg
7100 daN
7500 daN
9400 daN
7000 daN
11,8 s
12,3 s
8,4 s
7,9 s
17 s
17 s
14 s
13,5 s
4,75 s
4,2 s
27,6 km/h
27,6 km/h
13000 mm
3700 kg
500 mm
72 kg
29,8 m/mn
28,4 m/mn
42,1 m/mn
44,3 m/mn
25,9 m/mn
25,9 m/mn
31,5 m/mn
32,6 m/mn
26,1 °/s
29,5 °/s
INTRODUCTION TO SAFETY
DIMENSIONS AND LOAD CHART
MT 1337 SL Série 2
MT 1337 SL Turbo Série 2
MT 1337 SL Turbo MONO-ULTRA Série 2
MT 1337 SL
50° 60° 65°
14
12.68
13
40°
12
11
10
30°
9
8
7
20°
6
5
4
10° 3
0°
2
1
0
-6.5°
-1
10 9
9.46
8.65
8
7.65
7 6
5.9
5
4.75
4
3.9
3.3
3
2.4
2.85
2
2.2
SUIVANT NORME EN 1459 annexe B.
1
0.5m
0m
2 - 30
MT 1337 SL
60° 70° 70.5° 50°
14
13
40°
12
11
10
9
30°
8
20°
10°
5
4
3
7
6
2
1
0°
0
-5.5°
9
9.34
8
8.25
7 6 5
5.4
4.7
4 3 2
2.15
1
SUIVANT NORME EN 1459 annexe B.
0m
0.5m
INTRODUCTION TO SAFETY
MT 1337 SL Série 2
O
P2
P3
K
L
N
R
G1
G2
G3
H
H1
J
I
F
F1
G
D1
D2
E
A
B
C
C1
D
S
T
U1
U2
V
V1
V2
W
W1
W2
W3
Y
Z
1200 mm
2770 mm
2135 mm
2045 mm
5955 mm
5865 mm
4435 mm
7155 mm
1990 mm
1990 mm
500 mm
495 mm
500 mm
290 mm
4 °
4 °
1050 mm
950 mm
1040 mm
50 mm
1880 mm
125 mm
45,5 °
50 °
3660 mm ***
3935 mm ****
8720 mm ***
8870 mm ****
4665 mm
2590 mm
2730 mm *
2770 mm **
5600 mm ***
5750 mm ****
1320 mm ***
1470 mm ****
4000 mm ***
4150 mm ****
2425 mm
3820 mm
1050 mm
2350 mm
12 °
112 °
* : 1 st ASSEMBLY
** : 2 nd ASSEMBLY
*** : Up to machine Nr : 147615
**** : From machine Nr : 147616
MT 1337 SL Turbo Série 2
1200 mm
2770 mm
2135 mm
2045 mm
5955 mm
5865 mm
4435 mm
7155 mm
1990 mm
1990 mm
500 mm
495 mm
500 mm
290 mm
4 °
4 °
1050 mm
950 mm
1040 mm
50 mm
1880 mm
125 mm
45,5 °
50 °
3660 mm ***
3935 mm ****
8720 mm ***
8870 mm ****
4665 mm
2590 mm
2730 mm *
2770 mm **
5600 mm ***
5750 mm ****
1320 mm ***
1470 mm ****
4000 mm ***
4150 mm ****
2425 mm
3820 mm
1050 mm
2350 mm
12 °
112 °
MT 1337 SL Turbo
MONO-ULTRA Série 2
1200 mm
2770 mm
2135 mm
2045 mm
5955 mm
5865 mm
4435 mm
7155 mm
1990 mm
1990 mm
500 mm
495 mm
500 mm
290 mm
4 °
4 °
1050 mm
950 mm
1040 mm
50 mm
1890 to 1940 mm
125 mm
45,5 °
50 °
3660 mm ***
3935 mm ****
8720 mm ***
8870 mm ****
4665 mm
2590 mm
2730 mm *
2770 mm **
5600 mm ***
5750 mm ****
1320 mm ***
1470 mm ****
4000 mm ***
4150 mm ****
2425 mm
3820 mm
1050 mm
2350 mm
12 °
112 °
2 - 31
INTRODUCTION TO SAFETY
CHARACTERISTICS
MT 1637 SL Série 2
MT 1637 SL Turbo Série 2
MT 1637 SL Turbo MONO-ULTRA Série 2
F
RONT AND REAR TYRES
STANDARD
OPTION
OPTION
OPTION
OPTION
DIMENSIONS
440/80-24 T37 158B
DUNLOP
PRESSURE
4,5 Bar
Front unladen
Front laden
Rear unladen
Rear laden
15,5R25 L2 1* VKT Tub fire 5,6 Bar
BRIDGESTONE
Front unladen
Front laden
Rear unladen
Rear laden
400/80-24 T37 156B
DUNLOP
4,75 Bar
Front unladen
Front laden
Rear unladen
Rear laden
TYRE LOAD PRESSURE ON THE CONTACT SURFACE AREA OF THE CONTACT SURFACE
HARD GROUND LIGHT GROUND HARD GROUND LIGHT GROUND
2350 kg 8,4 kg/cm2
6300 kg 12,8 kg/cm2
3100 kg 9,1 kg/cm2
1000 kg 6,5 kg/cm2
2350 kg 8,1 kg/cm2
6300 kg 10,2 kg/cm2
3100 kg 8,4 kg/cm2
1000 kg 6,7 kg/cm2
2350 kg 9,4 kg/cm2
6300 kg 14,1 kg/cm2
3100 kg 10,2 kg/cm2
1000 kg 7,1 kg/cm2
2,3 kg/cm2
3,5 kg/cm2
2,5 kg/cm2
1,8 kg/cm2
3,7 kg/cm2
5 kg/cm2
3,9 kg/cm2
2,8 kg/cm2
2,6 kg/cm2
3,9 kg/cm2
2,8 kg/cm2
2 kg/cm2
280 cm2
490 cm2
340 cm2
155 cm2
290 cm2
619 cm2
368 cm2
150 cm2
250 cm2
445 cm2
305 cm2
140 cm2
1010 cm2
1780 cm2
1230 cm2
560 cm2
640 cm2
1260 cm2
785 cm2
360 cm2
900 cm2
1600 cm2
1090 cm2
500 cm2
15,5x25 12PR SGL DL 2A
GOODYEAR
15,5/80-24 SGI TL 16PR
GOODYEAR
445/70R24 XM47 TL 151G
MICHELIN
1200R24 X MINE D2
MICHELIN
15,5R25 XHA
MICHELIN
18R19,5 XF TL
MICHELIN
4,5 Bar
4,5 Bar
4,1 Bar
6,5 Bar
4 Bar
6,5 Bar
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
Front unladen
Front laden
Rear unladen
Rear laden
2350 kg 6,8 kg/cm2
6300 kg 8,5 kg/cm2
3100 kg
1000 kg
2350 kg
6300 kg 14,2 kg/cm2
3100 kg 11,3 kg/cm2
1000 kg
2350 kg
1000 kg
7 kg/cm2
7,1 kg/cm2
9,8 kg/cm2
7,4 kg/cm2
2,1 kg/cm2
6300 kg 3,4 kg/cm2
3100 kg 2,5 kg/cm2
1000 kg 1,2 kg/cm2
2350 kg 4,6 kg/cm2
6300 kg 7 kg/cm2
3100 kg 5,3 kg/cm2
1000 kg 2,6 kg/cm2
3,3 kg/cm2
3,7 kg/cm2
4,6 kg/cm2
3,9 kg/cm2
3,9 kg/cm2
2,7 kg/cm2
3,8 kg/cm2
3,1 kg/cm2
2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2
1,2 kg/cm2
2,6 kg/cm2
1,5 kg/cm2
0,5 kg/cm2
2350 kg 3,1 kg/cm2 1,45 kg/cm2
6300 kg 3,7 kg/cm2 1,65 kg/cm2
3100 kg 3,2 kg/cm2 1,49 kg/cm2
1000 kg 2 kg/cm2 0,93 kg/cm2
2350 kg 3,6 kg/cm2 1,67 kg/cm2
6300 kg 4,4 kg/cm2 2,03 kg/cm2
3100 kg 3,8 kg/cm2 1,77 kg/cm2
1,55 kg/cm2
345 cm2
740 cm2
440 cm2
140 cm2
240 cm2
445 cm2
275 cm2
135 cm2
1120 cm2
1830 cm2
1270 cm2
830 cm2
511 cm2
899 cm2
585 cm2
379 cm2
757 cm2
1719 cm2
963 cm2
499 cm2
653 cm2
1437 cm2
812 cm2
300 cm2
635 cm2
1365 cm2
810 cm2
260 cm2
880 cm2
1640 cm2
1015 cm2
490 cm2 cm2 cm2 cm2 cm2
2029 cm2
2454 cm2
2104 cm2
1842 cm2
1623 cm2
3809 cm2
2082 cm2
1070 cm2
1409 cm2
3101 cm2
1751 cm2
647 cm2
H
YDRAULIC CIRCUIT
- Type of pump
- Lifting, tilting, telescoping, tilting corrector, stabilizer, attachment circuit
. Max. rating capacity unladen
. Pressure
. Capacity
- Steering circuit
. Max. rating capacity unladen
. Pressure
. Capacity
- Braking circuit
. Max. rating capacity unladen
. Pressure
. Capacity
- Filtration
. Return
. 2nd body suction
Gear double pump with flow divider
1st body
98 L/mn
260 Bar
41 cm3
10 µ
100 µ
2nd body
98 L/mn
160 Bar
41 cm3
2nd body
98 L/mn
140 Bar
41 cm3
2nd body
98 L/mn
40 Bar
41 cm3
2 - 32
INTRODUCTION TO SAFETY
S
PECIFICATIONS
- Level of sound pressure in the driver's cab LpA
(According to standard prEN 12053 : 1995)
- Level of sound power in the LwA environment
(According to directive 2000 / 14 CE guaranteed)
MT 1637 SL Série 2
MT 1637 SL Turbo Série 2 + T M-U
- Travel speed of the lift truck
(Except particular conditions)
. Forward
. Reverse
- Standard lift height
- Rated capacity with standard attachment
- Load center
- Weight of forks (Each)
- Lifting motions (Jib retracted)
. Unladen lifting
. Laden lifting
. Unladen lowering
. Laden lowering
- Telescoping motions (Lifting jib)
. Extending of telescope I, unladen
. Extending of telescope I, Laden
. Retracting of telescope I, unladen
. Retracting of telescope I, Laden
. Extending of telescope II, unladen
. Extending of telescope II, Laden
. Retracting of telescope II, unladen
. Retracting of telescope II, Laden
. Extending of telescope III, unladen
. Extending of telescope III, Laden
. Retracting of telescope III, unladen
. Retracting of telescope III, Laden
- Reverse tilt time unladen
- Forward tilt time unladen
- Lift truck weight with standard attachment
. Unladen
. Rated load
- Axle weight with attached equipment (Transport position)
. Front unladen
Rated load
. Rear unladen
Rated load
- Tensible strain at coupling hook
. Unladen
. Rated load
MT 1637 SL Série 2
MT 1637 SL Turbo Série 2 + T M-U
- Break out force with bucket
(According to standard ISO 8313)
2 - 33
83,6 dB
105 dB
106 dB
13,9 s
14,7 s
10,6 s
10,2 s
7,96 s
9,7 s
7,15 s
7,25 s
10,4 s
11,5 s
9,7 s
8,7 s
5,3 s
8,4 s
10860 kg
14560 kg
27,6 km/h
27,6 km/h
15800 mm
3700 kg
500 mm
72 kg
12 s
12,5 s
8,5 s
8 s
30,3 m/mn
28,9 m/mn
42,8 m/mn
45 m/mn
14,8 m/mn
14 m/mn
19,5 m/mn
20,2 m/mn
25,9 m/mn
21,3 m/mn
28,9 m/mn
28,5 m/mn
19,8 m/mn
17,9 m/mn
21,3 m/mn
23,7 m/mn
23,4 °/s
14,7 °/s
4675 kg
12550 kg
6185 kg
2010 kg
7250 daN
7500 daN
9400 daN
7000 daN
INTRODUCTION TO SAFETY
DIMENSIONS AND LOAD CHART
MT 1637 SL Série 2
MT 1637 SL Turbo Série 2
MT 1637 SL Turbo MONO-ULTRA Série 2
MT 1637 SL
50° 60° 65°
13
12.29
40°
12
11
10
30°
9
8
7
20°
6
5
10°
4
3
2
1
0°
0
-5.5°
-1
10 9
8.97
8 7
7.20
6
5.60
5 4 3 2
4.65
3.95
3.35
2.45
2.90
2.05
1
SUIVANT NORME EN 1459 annexe B.
0.5m
0m
2 - 34
MT 1637 SL
50° 60° 68.5°
11
30°
10
20°
7
6
9
8
5
4
10°
3
17
15.8
16
40°
15
14
13
12
2
1
0°
-2°
0
-1
13 12 11 10
12.33
10.20
9 8
8.20
7 6
5.40
5
4.70
4 3 2
2.05
1
SUIVANT NORME EN 1459 annexe B.
0.5m
0m
INTRODUCTION TO SAFETY
MT 1637 SL Série 2
O
P2
P3
K
L
N
R
G1
G2
G3
H
H1
J
I
F
F1
G
D1
D2
E
A
B
C
C1
D
S
T
U1
U2
V
V1
V2
W
W1
W2
W3
Y
Z
1200 mm
2770 mm
2135 mm
2045 mm
5955 mm
5865 mm
4435 mm
7155 mm
1990 mm
1990 mm
500 mm
495 mm
500 mm
290 mm
4 °
4 °
1050 mm
950 mm
1040 mm
50 mm
1880 mm
125 mm
45,5 °
50 °
3660 mm ***
3935 mm ****
8720 mm ***
8870 mm ****
4665 mm
2590 mm
2730 mm *
2770 mm **
5600 mm ***
5750 mm ****
1320 mm ***
1470 mm ****
4000 mm ***
4150 mm ****
2425 mm
3820 mm
1050 mm
2350 mm
12 °
112 °
* : 1 st ASSEMBLY
** : 2 nd ASSEMBLY
*** : Up to machine Nr : 147615
**** : From machine Nr : 147616
MT 1637 SL Turbo Série 2
1200 mm
2770 mm
2135 mm
2045 mm
5955 mm
5865 mm
4435 mm
7155 mm
1990 mm
1990 mm
500 mm
495 mm
500 mm
290 mm
4 °
4 °
1050 mm
950 mm
1040 mm
50 mm
1880 mm
125 mm
45,5 °
50 °
3660 mm ***
3935 mm ****
8720 mm ***
8870 mm ****
4665 mm
2590 mm
2730 mm *
2770 mm **
5600 mm ***
5750 mm ****
1320 mm ***
1470 mm ****
4000 mm ***
4150 mm ****
2425 mm
3820 mm
1050 mm
2350 mm
12 °
112 °
MT 1637 SL Turbo
MONO-ULTRA Série 2
1200 mm
2770 mm
2135 mm
2045 mm
5955 mm
5865 mm
4435 mm
7155 mm
1990 mm
1990 mm
500 mm
495 mm
500 mm
290 mm
4 °
4 °
1050 mm
950 mm
1040 mm
50 mm
1890 to 1940 mm
125 mm
45,5 °
50 °
3660 mm ***
3935 mm ****
8720 mm ***
8870 mm ****
4665 mm
2590 mm
2730 mm *
2770 mm **
5600 mm ***
5750 mm ****
1320 mm ***
1470 mm ****
4000 mm ***
4150 mm ****
2425 mm
3820 mm
1050 mm
2350 mm
12 °
112 °
2 - 35
INTRODUCTION TO SAFETY
CHARACTERISTICS
MT 1740 SL Série 2
MT 1740 SL Turbo Série 2
F
RONT AND REAR TYRES
DIMENSIONS PRESSURE
TYRE LOAD
STANDARD
OPTION
OPTION
440/80-24 T37 158B
DUNLOP
16,5/85-24 14PR SGI TL
GOODYEAR
15,5R25 XHA
MICHELIN
4,5 Bar
Front unladen
Front laden
Rear unladen
Rear laden
4,5 Bar
Front unladen
Front laden
Rear unladen
Rear laden
5 Bar
Front unladen
Front laden
Rear unladen
Rear laden
H
YDRAULIC CIRCUIT
- Type of pump
- Lifting, tilting, telescoping, tilting corrector, stabilizer, attachment circuit
. Max. rating capacity unladen
. Pressure
. Capacity
- Steering circuit
. Max. rating capacity unladen
. Pressure
. Capacity
- Braking circuit
. Max. rating capacity unladen
. Pressure
. Capacity
- Filtration
. Return
. 2nd body suction kg kg kg kg kg kg kg kg kg kg kg kg
PRESSURE ON THE CONTACT SURFACE AREA OF THE CONTACT SURFACE
HARD GROUND LIGHT GROUND HARD GROUND LIGHT GROUND kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 kg/cm2 cm2 cm2 cm2 cm2 cm2 cm2 cm2 cm2 cm2 cm2 cm2 cm2 cm2 cm2 cm2 cm2 cm2 cm2 cm2 cm2 cm2 cm2 cm2 cm2
Gear double pump with flow divider
1st body
98 L/mn
260 Bar
41 cm3
2nd body
98 L/mn
160 Bar
41 cm3
2nd body
98 L/mn
140 Bar
41 cm3
2nd body
98 L/mn
40 Bar
41 cm3
10 µ
100 µ
2 - 36
INTRODUCTION TO SAFETY
S
PECIFICATIONS
- Level of sound pressure in the driver's cab LpA
(According to standard prEN 12053 : 1995)
- Level of sound power in the LwA environment
(According to directive 2000 / 14 CE guaranteed)
MT 1740 SL Série 2
MT 1740 SL Turbo Série 2
- Travel speed of the lift truck
(Except particular conditions)
. Forward
. Reverse
- Standard lift height
- Rated capacity with standard attachment
- Load center
- Weight of forks (Each)
- Lifting motions (Jib retracted)
. Unladen lifting
. Laden lifting
. Unladen lowering
. Laden lowering
- Telescoping motions (Lifting jib)
. Extending of telescope I, unladen
. Extending of telescope I, Laden
. Retracting of telescope I, unladen
. Retracting of telescope I, Laden
. Extending of telescope II, unladen
. Extending of telescope II, Laden
. Retracting of telescope II, unladen
. Retracting of telescope II, Laden
. Extending of telescope III, unladen
. Extending of telescope III, Laden
. Retracting of telescope III, unladen
. Retracting of telescope III, Laden
- Reverse tilt time unladen
- Forward tilt time unladen
- Lift truck weight with standard attachment
. Unladen
. Rated load
- Axle weight with attached equipment (Transport position)
. Front unladen
Rated load
. Rear unladen
Rated load
- Tensible strain at coupling hook
. Unladen
. Rated load
MT 1740 SL Série 2
MT 1740 SL Turbo Série 2
- Break out force with bucket
(According to standard ISO 8313)
2 - 37
83,6 dB
105 dB
106 dB
13,9 s
14,7 s
10,6 s
10,2 s
7,96 s
9,7 s
7,15 s
7,25 s
10,4 s
11,5 s
9,7 s
8,7 s
5,3 s
8,4 s kg kg
27,6 km/h
27,6 km/h
16650 mm
4000 kg
500 mm
72 kg s s s s m/mn m/mn m/mn m/mn
14,8 m/mn
14 m/mn
19,5 m/mn
20,2 m/mn
25,9 m/mn
21,3 m/mn
28,9 m/mn
28,5 m/mn
19,8 m/mn
17,9 m/mn
21,3 m/mn
23,7 m/mn
23,4 °/s
14,7 °/s kg kg kg kg daN daN daN
7000 daN
INTRODUCTION TO SAFETY
DIMENSIONS AND LOAD CHART
MT 1740 SL Série 2
MT 1740 SL Turbo Série 2
MT 1740 SL T
50° 60° 66.7°
12.33
13
40°
12
11
10
9
30°
8
6.06
7
6
20°
5
4
10°
3
2
1
0°
0
-4.1°
-1
10
3000KG
3500KG
4000KG
9 8
8.10
7
7.20
6
5.60
5 4 3
4.65
3.35
3.95
2.90
2 1
2.15
2.30
2.60
SUIVANT NORME EN 1459 annexe B.
0.5m
0m
2 - 38
MT 1740 SL T
50° 60° 70°
17
16.65
16
15
40°
14
13
12
11
30° 10
7
20°
6
9
8
5
4
10°
3
2
1
0°
0
2.3°
-1
13
12.35
12 11
12.30
10
10.20
9
9.30
8
8.20
7 6
5.40
5 4
4.50
4.90
3 2
2.10
SUIVANT NORME EN 1459 annexe B.
79.4°
1
0.5m
0m
INTRODUCTION TO SAFETY
P2
P3
R
L
N
O
I
J
K
G3
H
H1
D2
E
F
F1
G
G1
G2
C1
D
D1
A
B
C
V2
W
W1
W2
W3
Y
Z
S
T
U1
U2
V
V1
MT 1740 SL Série 2
1200 mm
2770 mm
2135 mm
2045 mm
5955 mm
5865 mm
4435 mm
7155 mm
1990 mm
1990 mm
500 mm
495 mm
500 mm
290 mm
4 °
4 °
1050 mm
950 mm
1040 mm
50 mm
1880 mm
125 mm
45,5 °
50 °
3935 mm
8870 mm
4665 mm
2590 mm
2770 mm
5750 mm
1470 mm
4150 mm
2425 mm
3820 mm
1050 mm
2350 mm
12 °
112 °
MT 1740 SL Turbo Série 2
1200 mm
2770 mm
2135 mm
2045 mm
5955 mm
5865 mm
4435 mm
7155 mm
1990 mm
1990 mm
500 mm
495 mm
500 mm
290 mm
4 °
4 °
1050 mm
950 mm
1040 mm
50 mm
1880 mm
125 mm
45,5 °
50 °
3935 mm
8870 mm
4665 mm
2590 mm
2770 mm
5750 mm
1470 mm
4150 mm
2425 mm
3820 mm
1050 mm
2350 mm
12 °
112 °
2 - 39
INTRODUCTION TO SAFETY
INSTRUMENTS AND CONTROLS
27
18
35
28
7
16
10
3
4
8
36
9
6
15
31
1
21
22
17
1
19
2
11 12
25
14
13
25
23
20
24
24
24
29
26
30
27
28
31
27
35
2 - 40
INTRODUCTION TO SAFETY
D
ESCRIPTION
1 - DRIVER'S SEAT
2 - SAFETY BELT
3 - SIGNAL LIGHTS PANEL
4 - FUEL LEVEL AND HOURMETER
5 - N/A
6 - SWITCH PANEL
7 - SWITCH AND LAMPS FOR ALIGNMENT OF THE WHEELS
8 - LIGHT SWITCH, HORN AND INDICATOR SWITCH
9 - IGNITION SWITCH
10 - BRAKING OIL TANK, FUSES AND RELAY ACCESS PANEL
11 - BRAKING OIL TANK
12 - FUSE AND RELAY PLATE
13 - WINDSCREEN WASHER TANK
14 - ROOF LIGHT
15 - ACCELERATOR PEDAL
16 - SERVICE BRAKE PEDAL AND TRANSMISSION CUT-OFF
17 - GEAR LEVER AND TRANSMISSION CUT-OFF
18 - FORWARD/REVERSE LEVER
19 - PARKING BRAKE LEVER
20 - STEERING SELECTION LEVER
21 - HYDRAULIC CONTROLS
22 - LOAD CHARTS FILE
23 - HEATER CONTROL
24 - WINDSCREEN DEMIST VENTS
25 - HEATING VENTS
26 - OPENING BUTTON FOR ACCESS PANEL HYDRAULIC OIL AND FUEL FILLING
27 - DOOR LOCK
28 - LOCKING HANDLE FOR UPPER HALF DOOR
29 - RELEASING BUTTON FOR UPPER HALF DOOR
30 - HANDLE FOR REAR WINDOW OPENING
31 - DOCUMENT HOLDER
32 - FRONT LIGHTS (NOT ILLUSTRATED)
33 - REAR LIGHTS (NOT ILLUSTRATED)
34 - FLASHING LIGHT (NOT ILLUSTRATED)
35 - SPIRIT LEVEL
36 - STEERING WHEEL REGULATING HANDLE
37 - TILTING CORRECTOR INDICATOR (NOT ILLUSTRATED)
NOTE : All the terms such as : RIGHT, LEFT, FRONT, REAR are meant for an observer seated on driver's seat and looking in front of him.
2 - 41
INTRODUCTION TO SAFETY
1 - D
RIVER
'
S SEAT
STANDARD
OPTION
MT 845 Série 2 MT 940 L Série 2 MT 1233 S Série 2
MT 1240 L Série 2 MT 1330 SL Série 2 MT 1337 SL Série 2
MT 1637 SL Série 2 MT 1740 SL Série 2
MT 845 Turbo Série 2 + T M-U MT 940 L Turbo Série 2 + T M-U
MT 1233 S Turbo Série 2 + T M-U
MT 1330 SL Turbo Série 2
MT 1637 SL Turbo Série 2 + T M-U
MT 1240 L Turbo Série 2 + T M-U
MT 1337 SL Turbo Série 2 + T M-U
MT 1740 SL Turbo Série 2
DESIGNED FOR MAXIMUM COMFORT, THIS SEAT CAN BE ADJUSTED AS FOLLOWS.
LONGITUDINAL ADJUSTMENT
- Pull locking lever 1 towards the right.
- Slide the seat to the required position.
- Release the lever and be sure it returns to the lock position.
SEAT SUSPENSION ADJUSTMENT
- Refer to the seat's graduation.
- Turn handle 2 depending on the driver's weight.
ADJUSTMENT OF THE ANGLE OF THE BACK-REST
- Pull locking lever 3 upwards.
- Slide the back-rest to the required position.
- Release the lever and be sure it returns to the lock position.
2
1
1 - D
RIVER
'
S SEAT
STANDARD
OPTION
MT 845 Turbo Série 2 + T M-U
MT 1233 S Turbo Série 2 + T M-U
MT 1330 SL Turbo Série 2
MT 1637 SL Turbo Série 2 + T M-U
MT 940 L Turbo Série 2 + T M-U
MT 1240 L Turbo Série 2 + T M-U
MT 1337 SL Turbo Série 2 + T M-U
MT 1740 SL Turbo Série 2
MT 845 Série 2 MT 940 L Série 2 MT 1233 S Série 2
MT 1240 L Série 2 MT 1330 SL Série 2 MT 1337 SL Série 2
MT 1637 SL Série 2 MT 1740 SL Série 2
DESIGNED FOR MAXIMUM COMFORT, THIS SEAT CAN BE ADJUSTED AS FOLLOWS.
LONGITUDINAL ADJUSTMENT
- Pull the locking lever 1 upwards.
- Slide the seat to the desired position.
- Release the lever and ensure it returns to the lock position.
SEAT CUSHION ADJUSTMENT
The front and the back of the seat cushion can be adjusted separately.
- To adjust the front, push the lever 2 downwards.
- Release it into one of the five possible positions.
- Same procedure to adjust the back by pulling the lever 2 upwards.
SEAT SUSPENSION ADJUSTMENT
- Turn the button 3 and adjust according to your weight.
ANGLE ADJUSTMENT OF THE BACK-REST
- Lean the back against the back-rest.
- Pull the lever 4 and place the back-rest into one of the possible positions.
2 - 42
4
3
1
2
3
INTRODUCTION TO SAFETY
1 - P
NEUMATIC DRIVER
'
S SEAT
(O
PTION
)
DESIGNED FOR MAXIMUM COMFORT, THIS SEAT CAN BE ADJUSTED AS
FOLLOWS.
WEIGHT AND SEAT HEIGHT ADJUSTMENT
WEIGHT ADJUSTMENT (FIG. A)
It is advised that you adjust the seat according to your weight when sitting.
- Switch on lift truck ignition.
- Push or pull lever 1 until green appears in display 2 indicating correct adjustment according to your weight.
NOTE : To avoid any health problems, it is recommended that the weight should be checked and adjusted before starting up the lift truck.
SEAT HEIGHT ADJUSTMENT (FIG. B)
When weight adjustment has been carried out, you can then modify seat height.
- Keep the ignition switched on.
- Push or pull lever 1 until green appears and adjust the height of the seat while checking that the green in display 2 remains visible.
To avoid causing any damage, do not activate the compressor for over 1 minute.
SEAT BACK-REST ANGLE ADJUSTMENT (FIG. C)
The back-rest angle of the seat may be adjusted to suit the individual.
- Press the left-hand button while pushing on the seat or relaxing pressure on the seat to find a comfortable position.
SEAT DEPTH ADJUSTMENT (FIG. D)
The depth of the seat may be adjusted to suit the individual.
- Press the right-hand button while raising or lowering the seat to find the desired position.
EXTENDING THE HEAD-REST (FIG. E)
- The height of the back-rest can be adjusted by pulling it upwards (The notches will click) up to the stop.
- The head-rest can be removed by applying sufficient pressure to pull it off the stop.
LUMBAR ADJUSTMENT (FIG. F)
This increases the comfort of the seat and the driver’s freedom of movement.
- Turn the handle either left or right to adjust the height or depth of the lumbar support.
E
A
B
C
D
F
2 - 43
INTRODUCTION TO SAFETY
ADJUSTMENT OF THE ANGLE OF THE BACK-REST (FIG. G)
- Support the back-rest, pull the lever and position the back-rest to find the desired position.
If you do not support the back-rest when making adjustments, it swings completely forwards.
HORIZONTAL SHOCK ABSORBER (FIG. H)
In certain conditions (e.g. driving with a trailer) it is advised that a horizontal shock absorber be used. The driver’s seat is thus better able to absorb jerks in the direction of travel.
- Position 1 : Horizontal shock absorber fitted.
- Position 2 : Horizontal shock absorber removed.
LONGITUDINAL ADJUSTMENT (FIG. I)
- Adjust the locking lever until you reach the position required. This then locks and the seat will not shift into another position.
MAINTENANCE (FIG. J)
Dirt may adversely affect the correct functioning of the seat. For this reason, make sure your seat is always clean.
- To clean or change the cushions, simply remove them from the seat frame.
A rocking head-rest increases the risk of an accident !
Avoid wetting the cushion fabric when cleaning. Check the resistance of the fabric on a small hidden area before using any fabric or plastic cleaner.
G
H
I
J
2 - S
AFETY BELT
- Sit correctly on the seat.
- Check that seat belt is not twisted.
- Place the seat belt at hip level and not across the stomach.
- Attach the seat belt and check that it locks.
- Adjust the seat belt to your body shape without squeezing your hip.
In no event should the lift truck be used if the seat belt is defective (Fixing, locking, cuts, tears, etc.). Repair or replace the seat belt immediately.
2 - 44
INTRODUCTION TO SAFETY
3 - S
IGNAL LIGHTS PANEL
When activating the electrical system of the lift truck, all the red lamps and the panel's buzzer must light to indicate their good working order. If one of the red lamps or the buzzer does not function, carry out the necessary repairs.
A - RED I.C. ENGINE OIL PRESSURE LAMP
If the lamp and the buzzer come on when the lift truck is running, stop the I.C. engine immediately and look for the cause (See oil level in I.C. engine crankcase).
A B C D E
F G H I J
B - RED I.C. ENGINE WATER TEMPERATURE LAMP
If the lamp and the buzzer come on when the lift truck is running, stop the I.C. engine immediately and investigate the cooling system for the cause of the malfunction.
C - RED TRANSMISSION OIL PRESSURE LAMP
The lamp and the buzzer come on when the pressure in the transmission, when driving forward, is abnormally low. Stop the lift truck and look for the cause (Insufficient transmission oil level, internal leak in the transmission, etc.).
NOTE : The signal light operates in forward travel conditions only, the signal should not be taken into account when the I.C.
engine is running at idle or is stopped.
D - RED AIR FILTER CLOGGED LAMP
The lamp and the buzzer come on when the air filter cartridge is clogged up. Stop the lift truck and carry out the necessary repairs (See cleaning and replacement requirements in chapter : FILTERS CARTRIDGES AND BELTS in paragraph : 3 -
MAINTENANCE).
E - RED TRANSMISSION OIL TEMPERATURE LAMP
The lamp and the buzzer come on when the converter oil temperature is abnormally high. Stop the lift truck and look for the cause of this overheating.
F - RED ALTERNATOR CHARGE LAMP
If the lamps B - C - D - E - F - J and the buzzer come on, when the lift truck is running, stop the I.C. engine immediately and check the electrical circuit as well as the alternator belt.
G - RED PARKING BRAKE LAMP
This lamp comes on when the parking brake is applied.
H - GREEN INDICATOR LAMP
I - BLUE MAIN BEAM LAMP
J - RED BRAKING OIL LEVEL LAMP
If the lamp and the buzzer come on, when the lift truck is running, stop the I.C. engine immediately and check the braking oil level. In the event of an abnormal dropping of the level, consult your dealer.
4 - F
UEL LEVEL AND HOURMETER
A - FUEL LEVEL
B - HOURMETER
B A
2 - 45
INTRODUCTION TO SAFETY
5 - N/A
The load status indicator allows the user to know at any moment if the lift truck is at the maximum authorised load limit.
OPERATION
Up to machine Nr : 147615
A
A - RED SIGNAL LIGHT (VISUAL ALARM)
This signal light comes on, when the lift truck reaches 100 % of the maximum authorized load. The sound alarm sounds simultaneously with the red signal light A.
B - SOUND ALARM SWITCH
Allows the sound alarm to be used or switched OFF. When not in use, the red signal light B1 shows that the sound alarm has been cut off and that only the visual alarm is working.
B
B1
C
C - TEST SWITCH
This switch enables the good working condition of the sound alarm and the red signal light to be checked. Check the good working condition each day, before using the lift truck.
OPERATION
From machine Nr : 147616
When the lift truck is switched on a control test is automatically carried out.
- Correct operation : All leds and the sound alarm function continuously for 2 seconds.
- Faulty operation : All leds and sound alarm function intermittently (Stop the lift truck and consult your dealer, never attempt a repair yourself).
A - LEDS (VISUAL ALARM) (FIG. A)
A1 - 4 green leds : The lift truck is operating safely.
A2 - 2 yellow leds : The lift truck is nearing the maximum authorised load limit.
A3 - 1 red led : The lift truck is at the maximum authorised load limit - slowly intermittent sound alarm is triggered.
A4 - 1 red led : The lift truck is overloaded - speedy intermittent sound alarm is triggered. Carry out positive hydraulic movements in the following order : raise and retract the jib.
B - SOUND ALARM SWITCH (FIG. A)
Allows the sound alarm to be used or switched OFF. When not in use, the red signal light B1 shows that the sound alarm has been cut off and that only the visual alarm is working.
C - TEST SWITCH (FIG. A)
Press the switch to check at any time the correct functioning of the load status indicator.
- Correct operation : All leds and the sound alarm function continuously.
- Faulty operation : All leds and the sound alarm function intermittently (Stop the lift truck and consult your dealer, never attempt a repair yourself).
D - STRAIN GAUGE (FIG. B)
Disassembly or adjustment of the strain gauge is prohibited, this must only be done by specially trained personnel, consult your dealer.
A1
A1
A1
A4
A3
A2
A2
A1
A
A
B
C
B1
B
2 - 46
INTRODUCTION TO SAFETY
6 - S
WITCH PANEL
A - HEATER BLOWER
This two speed switch allows warm or cold air to pass through the heating ventilators.
B - WARNING LIGHTS
This switch enables the L.H. and R.H. Indicators to be switched on simultaneously, with the ignition off. The signal light indicates that the switch is being used.
C - OPTION TRAILER BRAKING PRE-ARRANGEMENT
A C
Up to machine Nr : 147615
E
K
G
1
I
D - FRONT WINDSCREEN WIPER AND WINDSCREEN WASHER
This two position switch, when set on the "down" position and simultaneously pressed, allows the windscreen-washer and the windscreen wiper to be operated, and when set on the "up" position, the windscreen wiper to be operated.
E - REAR WINDSCREEN WIPER + ROOF WIPER OPTION
F - OPTION WORKING HEADLIGHT ON THE HEAD OF THE JIB
G - TRANSMISSION CUT-OFF
This switch does or does not allow the transmission to be cut-off on the service brake pedal.
- Position 1 : The signal light out, no transmission cut-off.
- Position 2 : The signal light is illuminated, there is a transmission cut-off.
A
B
C
D
From machine Nr : 147616
E
F
I
2
F
1
H J
H
B D K
2
G J
H - OPTION WORKING HEAD LIGHT
I - FLASHING LIGHT
J - OPTION WORKING TAIL LIGHT
K - OPTION ATTACHMENT HYDRAULIC LOCKING
MT 845 Turbo MONO-ULTRA Série 2
MT 940/1240 L Turbo MONO-ULTRA Série 2
MT 1233 S Turbo MONO-ULTRA Série 2
MT 1337/1637 SL Turbo MONO-ULTRA Série 2
See chapter : DESCRIPTION AND USE OF ELECTRIC AND HYDRAULIC OPTIONS in paragraph : 2 - DESCRIPTION.
L - OPTION HYDRAULIC MOVEMENTS CUT-OFF
See chapter : DESCRIPTION AND USE OF ELECTRIC AND HYDRAULIC OPTIONS in paragraph : 2 - DESCRIPTION.
L
2 - 47
INTRODUCTION TO SAFETY
7 - S
WITCH AND LAMPS FOR ALIGNMENT OF THE WHEELS
B A
Before selecting one of the three possible steering positions, bring the 4 wheels into alignment, i.e., in the straight ahead position.
A1
A2
A - GREEN LAMPS FOR ALIGNMENT OF THE WHEELS
These lamps come on to indicate the alignment of the wheels, in relation to the axle of the lift truck. The lamp A1 for the front wheels and the lamp A2 for the rear wheels.
B - SWITCH FOR ALIGNMENT OF THE WHEELS
This switch enables the use or not of the device for alignment of the wheels.The indicator light indicates its use.
B
WHEEL ALIGNMENT PROCEDURE
- Connect the switch (Signal light ON).
- Shift the distributor control lever for steering selection 1 in position B (4 wheel steering).
- Turn the steering wheel and bring the rear wheels into alignment until the lamp A2 is on.
- Shift the distributor control lever for steering selection 1 in position A (Highway traffic).
- Turn the steering wheel and bring the front wheels into alignment until the lamp A1 is on.
1
A
C
Before driving on roads, it is necessary to check the alignment of the rear wheels and to drive in front wheel steer. The control of the alignment of the rear wheels must be regularly done with the help of the green lamps, while driving the lift truck.
In case of anomalies, consult your dealer.
8 - L
IGHT SWITCH
,
HORN AND INDICATOR SWITCH
The switch controls the visual and sound alarms.
A - All lights are off, the direction indicators do not flash.
B - The right hand direction indicators flash.
C - The left hand direction indicators flash.
D - The sidelights and the rear lights are on.
E - The dipped headlights and the rear lights are on.
F - The main beam headlights and the rear lights are on.
G - Headlight signal.
Pressing the switch sounds the horn.
NOTE : The positions D - E - F - G can be carried out without the ignition being on.
9 - I
GNITION SWITCH
The key switch has five positions :
P - Ignition off, parking position.
O - Ignition switched off and engine stopped.
I - Ignition on.
II - Heating.
III - The engine starts, return to position i as soon as the key is released.
10 - B
RAKING OIL TANK
,
FUSES AND RELAY ACCESS PANEL
11 - B
RAKING OIL TANK
See chapter : B - EVERY 50 HOURS SERVICE in paragraph : 3 - MAINTENANCE.
G
A
G D
G
E
F
C
A
B
2 - 48
INTRODUCTION TO SAFETY
12 - F
USE AND RELAY PLATE
F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 F14
K0 - Transmission cut-off relay.
K1 - Transmission cut-off relay.
K2 - Forward gear relay.
K3 - Reverse gear relay.
K4 - Safety system starting switch relay.
K5 - Transmission oil pressure relay.
K6 - Flashing unit.
K7 - Buzzer.
F15 F16 F17 F18 F19 F20 F21 F22 F23 F24
K4 K7 K6
NOTE : Replace a used fuse with a new fuse of the same quality and capacity. Never reuse a repaired fuse.
K2
K3
F1 - (15A MAX.) - Electric controls of hydraulic movements (15A). MT 845 Turbo MONO-ULTRA Série 2
MT 940/1240 L Turbo MONO-ULTRA Série 2
MT 1233 S Turbo MONO-ULTRA Série 2
MT 1337/1637 SL Turbo MONO-ULTRA Série 2
- OPTION Fuel reheating (15A).
- OPTION Pneumatic seat (15A).
F2 - (7,5A MAX.) - Alignment of the wheels (5A).
F3 - (10A MAX.) - Sound alarm (10A).
- Stop switch (10A).
F4 - (10A MAX.) - Security lifting (10A). MT 1740 SL Série 2 + T
- OPTION Jib head light (10A).
- OPTION Electrovalve on jib head (10A).
- OPTION Electrical jib provision (10A).
- OPTION Anti-theft device provision (10A).
F5 - (10A MAX.) - Left indicators (7,5A).
F6 - (10A MAX.) - Right sidelights (7,5A).
- Fuel gauge lighting (7,5A).
- Hourmeter lighting (7,5A).
- OPTION Service plate lighting (7,5A).
F7 - (10A MAX.) - Left sidelights (7,5A).
F8 - (10A MAX.) - Flashing light (7,5A).
F9 - (10A MAX.) - OPTION Working tail light (10A).
F10 - (10A MAX.) - OPTION Front working head light (10A).
F11 - (10A MAX.) - OPTION Insulation of the compensation cylinders (7,5A). MT 845 Série 2 + T
MT 940 L Série 2 + T
- OPTION Air conditioning (7,5A).
F12 - (7,5A MAX.) - OPTION (7,5A) MT 845 Série 2 + T + T M-U
- Security stabilizers (7,5A) MT 1233 S Série 2 + T + T M-U
- Security tilting corrector (7,5A) MT 940/1240 L Série 2 + T + T M-U
- Security stabilizers and tilting corrector (7,5A) MT 1330/1740 SL Série 2 + T
MT 1337/1637 SL Série 2 + T + T M-U
F13 - (15A MAX.) - Gear reverser (15A).
- Transmission cut-off (15A).
- Reverse lights (15A).
- Reverse buzzer alarm (15A).
F14 - (15A MAX.) - Option (10A).
- Security telescope III (10A). MT 1637 SL Série 2 + T + T M-U
MT 1740 SL Série 2 + T
- OPTION Hydraulic movements cut-off (10A).
- OPTION Attachment hydraulic locking device (10A). MT 845 Turbo MONO-ULTRA Série 2
MT 940/1240 L Turbo MONO-ULTRA Série 2
MT 1233 S Turbo MONO-ULTRA Série 2
MT 1337/1637 SL Turbo MONO-ULTRA Série 2
F15 - (10A MAX.) - Signal lamp panel (5A).
- Fuel gauge (5A).
- Hourmeter (5A).
2 - 49
K5
K1
K0
INTRODUCTION TO SAFETY
F16 - (10A MAX.) - Indicators power supply (10A).
F17 - (10A MAX.) - Front windscreen wiper and windscreen washer (10A).
F18 - (15A MAX.) - Main beam (15A).
- Main beam lamp (15A).
F19 - (10A MAX.) - Right indicators (7,5A).
F20 - (15A MAX.) - Low beam (15A).
F21 - (15A MAX.) - Hazard warning lights power supply (15A).
- Roof light (15A).
- OPTION (+)permanent (15A).
F22 - (25A MAX.) - Light switch power supply, horn and indicators (25A).
F23 - (10A MAX.) - Rear windscreen wiper (7,5A).
- OPTION Roof windscreen wiper (7,5A).
F24 - (15A MAX.) - Heating (15A).
F25 - (20A MAX.) - Preheating I.C. engine (20A). (From machine Nr : 000000)
13 - W
INDSCREEN WASHER TANK
See chapter : B - EVERY 50 HOURS SERVICE in paragraph : 3 - MAINTENANCE.
14 - R
OOF LIGHT
15 - A
CCELERATOR PEDAL
16 - S
ERVICE BRAKE PEDAL AND TRANSMISSION CUT
-
OFF
The pedal applies on the front and rear wheels by an hydraulic servo-brake system, and allows the lift truck to be slowed down and stopped. Depending on the position of the transmission cut-off switch, it enables the free travel to cut off transmission (See chapter : 6 - SWITCH PANEL in paragraph : 2 - DESCRIPTION).
17 - G
EAR LEVER AND TRANSMISSION CUT
-
OFF
In order to change speeds, it is necessary to cut the transmission by pressing the button
1 on the lever.
1rd gear : To the right, backwards.
2th gear : To the right, forwards.
3st gear : To the left, backwards.
4nd gear : To the left, forwards.
1
4
3
2
1
USING THE GEARS ON THE GEARBOX
- On these lift trucks with a torque converter, it is not necessary to automatically start up in 1st speed and progress up the gears.
The choice of gear ratio should be made carefully according to the nature of the work being carried out. A poor choice may result in the extremely rapid elevation of the transmission oil temperature through excessive slipping of the converter, which could lead to serious damage to the transmission (it is essential to stop and change the working conditions if the transmission oil temperature indicator light comes on). This poor choice may also result in a reduction in the lift truck's performance in forward speed. When the forward force increases, the forward speed in the r gear (for example 3rd gear) may be lower than the forward speed that could be obtained with the r-1 gear (in 2nd instead of the 3rd).
2 - 50
INTRODUCTION TO SAFETY
In general, we would advise you to use the following gears according to the nature of the work being carried out.
• On the road : Set off in 3rd gear and go up to 4th if the conditions and state of the road permit it. In hilly areas, set off in 2nd gear and go up to 3rd if the conditions and state of the road permit it.
• With a trailer on the road : Set off in 2nd gear and go up to 3rd if the conditions and state of the road permit it.
• Handling : 3rd gear.
2nd gear in restricted spaces.
• Earth moving : 1st gear.
• Loading (reclaiming with bucket, manure fork, etc.) : 2nd gear.
18 - F
ORWARD
/
REVERSE LEVER
When operating this control, the lift truck should be travelling at slow speed and not accelerating. When the reverser is in the neutral position a mechanical lock prevents an accidental shifting movement.
FORWARD : Lift slightly and push the lever forwards (Position A).
REVERSE : Lift slightly and pull the lever backwards (Position B).
NEUTRAL : To start the lift truck, the lever must be in neutral (Position C).
NOTE : The reverse lights and the sound alarm on reverse motion indicate that the lift truck is running in reverse motion.
19 - P
ARKING BRAKE LEVER
To prevent accidental loosening or release, the lever is fitted with safety locking.
- To apply the parking brake, pull the lever backwards (Position A).
- To loosen the parking brake, release and push the lever forwards (Position B).
A
C
B
B
A
20 - S
TEERING SELECTION LEVER
Before selecting one of the three possible steering positions, bring the 4 wheels into alignment, i.e., in the straight ahead position.
(See chapter : 7 - SWITCH AND LAMPS FOR ALIGNMENT OF THE WHEELS in paragraph : 2 - DESCRIPTION).
A - Front wheel steer (Highway traffic).
B - Front and rear wheels steer in opposite direction (4 wheel steer).
C - Front and rear wheels steer in the same direction (Crab steer).
HIGHWAY
TRAFFIC
4 WHEEL
STEER
CRAB
STEER
B
A
1
C
2 - 51
INTRODUCTION TO SAFETY
21 - H
YDRAULIC CONTROLS
Do not attempt to alter the hydraulic system pressure by interfering with the pressure regulating valve. In the event of suspected malfunction, contact your dealer. ANY
ALTERATION MAY RENDER THE WARRANTY NULL AND VOID.
Use the hydraulic controls carefully without jerking, to avoid accidents caused by shaking the lift truck.
MT 845 Série 2 + Turbo
LEVER A : Controls the lifting of the load and the tilt of the carriage.
- The lever backwards when lifting.
- The lever forwards when lowering.
- The lever to the left for reverse tilt.
- The lever to the right for forward tilt.
LEVER B : Controls the telescoping.
- The lever backwards for the retraction.
- The lever forwards for the extension.
LEVER C : Controls the additional attachment.
MT 940/1240 L Série 2 + Turbo
LEVER A : Controls the lifting of the load and the tilt of the carriage.
- The lever backwards when lifting.
- The lever forwards when lowering.
- The lever to the left for reverse tilt.
- The lever to the right for forward tilt.
LEVER B : Controls the telescoping.
- The lever backwards for the retraction.
- The lever forwards for the extension.
NOTE : MT 1240 L Série 2 + Turbo
When completely retracting the telescopes, insistently operate the control so as to allow all the telescopes to retract fully.
LEVER C : Controls the additional attachment.
LEVER D : Controls the tilting corrector.
- The lever to the left when tilting the lift truck on the left.
- The lever to the right when tilting the lift truck on the right.
NOTE : Tilt can be corrected up to the carriage articulation axle height of 3m50 from the ground, with the jib retracted.
MT 1233 S Série 2 + Turbo
LEVER A : Controls the lifting of the load and the tilt of the carriage.
- The lever backwards when lifting.
- The lever forwards when lowering.
- The lever to the left for reverse tilt.
- The lever to the right for forward tilt.
LEVER B : Controls the telescoping.
- The lever backwards for the retraction.
- The lever forwards for the extension.
NOTE : When completely retracting the telescopes, insistently operate the control so as to allow all the telescopes to retract fully.
LEVER C : Controls the additional attachment.
LEVER D : Controls the L.H. stabiliser.
- The lever backwards when lifting.
- The lever forwards when lowering.
LEVER E : Controls the R.H. stabiliser.
- The lever backwards when lifting.
- The lever forwards when lowering.
NOTE : The stabilisers can only be lifted after the jib have been retracted.
2 - 52
B
C
A
B
C
A
D
B
C
A
D
E
INTRODUCTION TO SAFETY
MT 1330/1337 SL Série 2 + Turbo
LEVER A : Controls the lifting of the load and the tilt of the carriage.
- The lever backwards when lifting.
- The lever forwards when lowering.
- The lever to the left for reverse tilt.
- The lever to the right for forward tilt.
LEVER B : Controls the telescoping.
- The lever backwards for the retraction.
- The lever forwards for the extension.
NOTE : When completely retracting the telescopes, insistently operate the control so as to allow all the telescopes to retract fully.
LEVER C : Controls the additional attachment.
LEVER D : Controls the L.H. stabiliser.
- The lever backwards when lifting.
- The lever forwards when lowering.
LEVER E : Controls the R.H. stabiliser.
- The lever backwards when lifting.
- The lever forwards when lowering.
NOTE : The stabilisers can only be lifted after the jib have been retracted.
LEVER F : Controls the tilting corrector.
- The lever to the left when tilting the lift truck on the left.
- The lever to the right when tilting the lift truck on the right.
NOTE : Tilt can be corrected up to the carriage articulation axle height of 3m50 from the ground, with the jib retracted.
MT 1637/1740 SL Série 2 + Turbo
LEVER A : Controls the lifting of the load and the tilt of the carriage.
- The lever backwards when lifting.
- The lever forwards when lowering.
- The lever to the left for reverse tilt.
- The lever to the right for forward tilt.
LEVER B : Controls the telescoping of the telescopes I and II.
- The lever backwards for the retraction.
- The lever forwards for the extension.
LEVER C : Controls the telescoping of the telescope III.
- The lever backwards for the retraction.
- The lever forwards for the extension.
NOTE : When completely retracting the telescopes, insistently operate the control so as to allow all the telescopes to retract fully.
The telescoping of the telescope III can only be carried out with the stabilizers extended in lower position. For safety reasons, the telescope III should be the last to be extended and the first to be retracted.
LEVER D : Controls the additional attachment.
LEVER E : Controls the L.H. stabiliser.
- The lever backwards when lifting.
- The lever forwards when lowering.
LEVER F : Controls the R.H. stabiliser.
- The lever backwards when lifting.
- The lever forwards when lowering.
NOTE : The stabilisers can only be lifted after the jib have been retracted.
LEVER G : Controls the tilting corrector.
- The lever to the left when tilting the lift truck on the left.
- The lever to the right when tilting the lift truck on the right.
NOTE : Tilt can be corrected up to the carriage articulation axle height of 3m50 from the ground, with the jib retracted.
2 - 53
B
C
A
D
E
F
D
C
B
A
E
F
G
INTRODUCTION TO SAFETY
MT 845 Turbo MONO-ULTRA Série 2
BUTTON A : Controls the lifting of the load and the tilt of the carriage.
- The lever backwards when lifting.
- The lever forwards when lowering.
- The lever to the left for reverse tilt.
- The lever to the right for forward tilt.
BUTTON B : Controls the telescoping and an additional attachment.
- The lever backwards for the retraction.
- The lever forwards for the extension.
- The lever to the left and to the right for the additional attachment.
BUTTON C : OPTION Attachment hydraulic locking device.
and/or
OPTION Jib head electrovalve.
1st ASSEMBLY
A
C
B
C
2nd ASSEMBLY
A
B
MT 940/1240 L Turbo MONO-ULTRA Série 2
BUTTON A : Controls the lifting of the load and the tilt of the carriage.
- The lever backwards when lifting.
- The lever forwards when lowering.
- The lever to the left for reverse tilt.
- The lever to the right for forward tilt.
BUTTON B : Controls the telescoping and an additional attachment.
- The lever backwards for the retraction.
- The lever forwards for the extension.
- The lever to the left and to the right for the additional attachment.
NOTE : MT 1240 L Turbo MONO-ULTRA Série 2
When completely retracting the telescopes, insistently operate the control so as to allow all the telescopes to retract fully.
BUTTON C : OPTION Attachment hydraulic locking device.
and/or
OPTION Jib head electrovalve.
BUTTON D : Controls the tilting corrector.
- The lever to the left when tilting the lift truck on the left.
- The lever to the right when tilting the lift truck on the right.
NOTE : Tilt can be corrected up to the carriage articulation axle height of
3m50 from the ground, with the jib retracted.
MT 1233 S Turbo MONO-ULTRA Série 2
BUTTON A : Controls the lifting of the load and the tilt of the carriage.
- The lever backwards when lifting.
- The lever forwards when lowering.
- The lever to the left for reverse tilt.
- The lever to the right for forward tilt.
BUTTON B : Controls the telescoping and an additional attachment.
- The lever backwards for the retraction.
- The lever forwards for the extension.
- The lever to the left and to the right for the additional attachment.
NOTE : When completely retracting the telescopes, insistently operate the control so as to allow all the telescopes to retract fully.
1st ASSEMBLY
A
D
C
B
1st ASSEMBLY
D
E
A
B
C
C
D
2nd ASSEMBLY
A
B
2nd ASSEMBLY
A
D
E
B
C
2 - 54
INTRODUCTION TO SAFETY
BUTTON C : OPTION Attachment hydraulic locking device.
and/or
OPTION Jib head electrovalve.
BUTTON D : Controls the L.H. stabiliser.
- The lever backwards when lifting.
- The lever forwards when lowering.
BUTTON E : Controls the R.H. stabiliser.
- The lever backwards when lifting.
- The lever forwards when lowering.
NOTE : The stabilisers can only be lifted after the jib have been retracted.
MT 1337 SL Turbo MONO-ULTRA Série 2
BUTTON A : Controls the lifting of the load and the tilt of the carriage.
- The lever backwards when lifting.
- The lever forwards when lowering.
- The lever to the left for reverse tilt.
- The lever to the right for forward tilt.
BUTTON B : Controls the telescoping and an additional attachment.
- The lever backwards for the retraction.
- The lever forwards for the extension.
- The lever to the left and to the right for the additional attachment.
NOTE : When completely retracting the telescopes, insistently operate the control so as to allow all the telescopes to retract fully.
BUTTON C : OPTION Attachment hydraulic locking device.
and/or
OPTION Jib head electrovalve.
BUTTON D : Controls the L.H. stabiliser.
- The lever backwards when lifting.
- The lever forwards when lowering.
BUTTON E : Controls the R.H. stabiliser.
- The lever backwards when lifting.
- The lever forwards when lowering.
NOTE : The stabilisers can only be lifted after the jib have been retracted.
BUTTON F : Controls the tilting corrector.
- The lever to the left when tilting the lift truck on the left.
- The lever to the right when tilting the lift truck on the right.
NOTE : Tilt can be corrected up to the carriage articulation axle height of
3m50 from the ground, with the jib retracted.
1st ASSEMBLY
D
E
A
B
F
C
C
F
2nd ASSEMBLY
A
D E
B
2 - 55
INTRODUCTION TO SAFETY
MT 1637 SL Turbo MONO-ULTRA Série 2
BUTTON A : Controls the lifting of the load and the tilt of the carriage.
- The lever backwards when lifting.
- The lever forwards when lowering.
- The lever to the left for reverse tilt.
- The lever to the right for forward tilt.
BUTTON B : Controls the telescoping of the telescopes I and II and an additional attachment.
- The lever backwards for the retraction.
- The lever forwards for the extension.
- The lever to the left and to the right for the additional attachment.
BUTTON C : Controls the telescoping of the telescope III and an option.
- The lever backwards for the retraction.
- The lever forwards for the extension.
- The lever to the left and to the right for :
OPTION Attachment hydraulic locking device.
1st ASSEMBLY
A
F
D
E
C
B
C
2nd ASSEMBLY
A
F
D
E
B and/or
OPTION Jib head electrovalve.
NOTE : When completely retracting the telescopes, insistently operate the control so as to allow all the telescopes to retract fully.
The telescoping of the telescope III can only be carried out with the stabilizers extended in lower position. For safety reasons, the telescope III should be the last to be extended and the first to be retracted.
BUTTON D : Controls the L.H. stabiliser.
- The lever backwards when lifting.
- The lever forwards when lowering.
BUTTON E : Controls the R.H. stabiliser.
- The lever backwards when lifting.
- The lever forwards when lowering.
NOTE : The stabilisers can only be lifted after the jib have been retracted.
BUTTON F : Controls the tilting corrector.
- The lever to the left when tilting the lift truck on the left.
- The lever to the right when tilting the lift truck on the right.
NOTE : Tilt can be corrected up to the carriage articulation axle height of 3m50 from the ground, with the jib retracted.
2 - 56
INTRODUCTION TO SAFETY
22 - L
OAD CHARTS FILE
This file includes the description of the hydraulic controls and the load charts of the attachments used on the lift truck.
23 - H
EATER CONTROL
Allows the temperature inside the cab to be adjusted.
A - With the valve closed, the fan delivers fresh air.
B - With the valve opened completely, the fan delivers warm air.
The intermediate positions allow the temperature to be adjusted.
A B
24 - W
INDSCREEN DEMIST VENTS
For optimum effectiveness, close the heating ventilators.
25 - H
EATING VENTS
These heating vents enable the air to be directed to the interior of the cabin and onto the side windows.
26 - O
PENING BUTTON FOR ACCESS PANEL HYDRAULIC OIL AND FUEL FILLING
- Push the button to open the access panel.
- Push the panel to close it.
27 - D
OOR LOCK
Two keys are provided with the lift truck to enable the cabin to be locked.
28 - L
OCKING HANDLE FOR UPPER HALF DOOR
29 - R
ELEASING BUTTON FOR UPPER HALF DOOR
30 - H
ANDLE FOR REAR WINDOW OPENING
EMERGENCY EXIT
Use the rear window as an emergency exit, if it is impossible to leave the cab by the door.
31 - D
OCUMENT HOLDER
Ensure that the operator's manual is in its place in the document holder.
NOTE : An OPTION waterproof document holder exists.
2 - 57
INTRODUCTION TO SAFETY
32 - F
RONT LIGHTS
A - Left front indicator.
B - Left front dipped headlight.
C - Left front main beam.
D - Left front sidelight.
E - Right front indicator.
F - Right front dipped headlight.
G - Right front main beam.
H - Right front sidelight.
MT 845 Série 2 + Turbo + Turbo MONO-ULTRA
MT 940 L Série 2 + Turbo + Turbo MONO-ULTRA
MT 1233 S Série 2 + Turbo + Turbo MONO-ULTRA
MT 1240 L Série 2 + Turbo + Turbo MONO-ULTRA
MT 1330 SL Série 2 + Turbo
G
E H
F
D
C
B
A
MT 1337 SL Série 2 + Turbo + Turbo MONO-ULTRA
MT 1637 SL Série 2 + Turbo + Turbo MONO-ULTRA
MT 1740 SL Série 2 + Turbo
E
G
H
F
D
C
B
33 - R
EAR LIGHTS
A - Left rear indicator.
B - Left rear stoplight.
C - Left tail light.
D - Left rear reverse light.
E - Left rear fog light (OPTION).
F - Right rear fog light (OPTION).
G - Right rear reverse light.
H - Right tail light.
I - Right rear stoplight.
J - Right rear indicator.
A B C D E
34 - F
LASHING LIGHT
The flashing light is dismountable to make it possible, for example, to reduce the height of the lift truck or to avoid being stolen.
- Unscrew the screw 1 and lay down the flashing light.
- Protect the bracket 2 with the cap 3.
F G H I J
3
1
2
A
2 - 58
INTRODUCTION TO SAFETY
35 - S
PIRIT LEVEL
As assembly
Enables the operator to check that the lift truck is in the horizontal position.
36 - S
TEERING WHEEL REGULATING HANDLE
MT 845 Turbo MONO-ULTRA Série 2
MT 940/1240 L Turbo MONO-ULTRA Série 2
MT 1233 S Turbo MONO-ULTRA Série 2
MT 1337/1637 SL Turbo MONO-ULTRA Série 2
This handle enables the angle and height of the steering wheel to be adjusted.
- Turn handle 1 towards A to loosen and adjust steering wheel.
- Turn handle 1 towards B to lock steering wheel in the position required.
37 - T
ILTING INDICATOR
MT 940 L Série 2 + Turbo + Turbo MONO-ULTRA
MT 1240 L Série 2 + Turbo + Turbo MONO-ULTRA
MT 1330 SL Série 2 + Turbo
MT 1337 SL Série 2 + Turbo + Turbo MONO-ULTRA
MT 1637 SL Série 2 + Turbo + Turbo MONO-ULTRA
MT 1740 SL Série 2 + Turbo
The indicator informs the user about the tilting given to the lift truck.
- The tip of the retracted indicator indicates the tilting towards the left.
- The tip of the extended indicator indicates the tilting towards the right.
2 - 59
B
1
A
INTRODUCTION TO SAFETY
TOWING PIN AND HOOK
Located at the rear of the lift truck, this device is used to attach a trailer. Its capacity is limited for each lift truck by the
Authorised Gross Vehicle Weight (A.G.V.W), tractive effort and maximum vertical force on the coupling point. This information is given on the manufacturer's plate fixed to each lift truck (See chapter : IDENTIFICATION OF THE LIFT TRUCK in paragraph
: 2 - DESCRIPTION).
- To use a trailer, see current regulations in your country (Maximum running speed, braking, maximum weight of trailer, etc.).
- Verify the trailer's condition before using it (Tyre condition and pressures, electrical connection, hydraulic hose, braking system…).
Do not tow a trailer or accessory which is not in perfect working order. Using a trailer in poor condition may effect the lift truck's steering and braking, and hence safety.
If a third party helps in coupling or uncoupling the trailer, this person must be permanently visible to the driver and wait until the lift truck has stopped, the handbrake is on and the engine is switched off before performing the operation.
NOTE : There is an OPTIONAL rear-view mirror which allows the lift truck to be approached more closely to the trailer ring.
A - T
OWING PIN
(F
IG
. A)
MT 845 Série 2 + Turbo + Turbo MONO-ULTRA
MT 940 L Série 2 + Turbo + Turbo MONO-ULTRA
MT 1240 L Série 2 + Turbo + Turbo MONO-ULTRA
MT 1337 SL Série 2 + Turbo + Turbo MONO-ULTRA
MT 1637 SL Série 2 + Turbo + Turbo MONO-ULTRA
MT 1740 SL Série 2 + Turbo
COUPLING AND UNCOUPLING THE TRAILER
- To couple the trailer, position the lift truck as close as possible to the trailer ring.
- Put the handbrake on and switch off the IC engine.
- Remove the clip 1, lift the trailer pin 2 and place or remove the trailer ring.
Be careful not to get your fingers caught or crushed during this operation.
Do not forget to put clip 1 back in place.
When uncoupling, make sure that the trailer is supported independently.
A
2
1
B - P
ROJECTING HOOK
(F
IG
. B)
MT 1233 S Série 2 + Turbo + Turbo MONO-ULTRA
MT 1330 SL Série 2 + Turbo
COUPLING AND UNCOUPLING THE TRAILER
- To couple the trailer, position the lift truck as close as possible to the trailer ring.
- Put the handbrake on and switch off the IC engine.
- Remove the clip 1, lift the trailer pin 2 and place or remove the trailer ring.
Be careful not to get your fingers caught or crushed during this operation.
Do not forget to put clip 1 back in place.
When uncoupling, make sure that the trailer is supported independently.
2
B
1
2 - 60
INTRODUCTION TO SAFETY
C - A
DJUSTABLE PROJECTING HOOK
(O
PTION
) (F
IG
. C)
COUPLING AND UNCOUPLING THE TRAILER
- To couple the trailer, position the lift truck as close as possible to the trailer ring.
- Put the handbrake on and switch off the engine.
- Set the coupling fitting 1 according to the height of the trailer ring.
Do not forget to put rods and clips back in place.
- Remove pin 2, lift the towing pin 3 and insert or remove the trailer ring.
Be careful not to get your fingers caught or crushed during this operation.
Do not forget to put clip 2 back in place.
When uncoupling, make sure that the trailer is supported independently.
D - E
LECTRICAL CONNECTION
(O
PTION
) (F
IG
. D)
- Connect the male plug to the female socket 1 on the lift truck and make sure the trailer lights work properly.
D
1
C
3
2
1
E - C
ONNECTING THE BRAKING SYSTEM
(O
PTION
) (F
IG
. E)
- Connect the brake hose to the provided brake unit 2 on the lift truck.
- Make sure the trailer brakes are working properly and test the effects of braking before taking the trailer onto the public highway.
E
2
2 - 61
INTRODUCTION TO SAFETY
DESCRIPTION AND USE OF ELECTRIC AND HYDRAULIC OPTIONS
1 - R
EAR ELECTRIC SOCKET
Enables power supply connection for a trailer (See chapter : TOWING PIN AND HOOK in paragraph : 2 - DESCRIPTION) or signalling bar.
Rear stoplight
Right tail light
Left rear indicator
Left tail light
Earth
Right rear indicator
2 - B
ATTERY CUT
-
OFF
3 - S
ERVICE PLATE
4 - S
ERVICE PLATE LIGHTING
5 - P
REHEATING ROD
Enables the motor unit to be kept warm during prolonged periods of stoppage and thus, ensures the improved start-up of the I.C. engine.
SUPPLY CHARACTERISTICS OF PREHEATING SYSTEM :
• Rated range of power : 220-240V ; 50-60Hz
• Current consumed : 4,5A
• Equipment in class 1
• Equipment connectable only on feeder circuit TT or TN
• Category of insulation 2
ENVIRONMENTAL CONDITIONS IN USE :
• Maximum ambient temperature for using preheating : + 25° C
• Pollution level 2
CONDITIONS FOR CONNECTION AND USE OF PREHEATING :
- The preheating system should not be used for an external ambient temperature higher than + 25° C.
- It is essential that the power supply to the preheating system is :
• Effected with a cable that conforms to the installation standards in force and contains a protective earth conductor.
• Contains an appropriate sectioning system.
• Incorporates an appropriate safety system against short circuits (fuses or circuit breaker) and a differential circuit breaker with 30mA sensitivity.
- Only connect to and disconnect from the power supply while the unit is off and the I.C.
engine is stopped.
2 - 62
INTRODUCTION TO SAFETY
6 - DIGICODE
ANTI
-
THEFT SYSTEM
7 - E
LECTRICAL JIB PROVISION
Enables an electrical or hydraulic function to be used at the head of the jib.
8 - I
NTERIOR DRAIN
-
BACK
MT 1233 S Série 2 + Turbo + Turbo MONO-ULTRA
MT 1240 L Série 2 + Turbo + Turbo MONO-ULTRA
MT 1330 SL Série 2 + Turbo
MT 1337 SL Série 2 + Turbo + Turbo MONO-ULTRA
Enables connection of an attachment for which drain-back is required.
9 - E
XTERIOR DRAIN
-
BACK
Enables connection of an attachment for which drain-back is required.
10 - H
YDRAULIC ATTACHMENT LOCKING
Enables attachment locking to be controlled on the carriage and the use of a hydraulic attachment on the same hydraulic circuit (See chapter : PICKING UP THE
ATTACHMENTS in paragraph : 4 - ADAPTABLE ATTACHMENTS IN OPTION ON THE
RANGE).
2 - 63
INTRODUCTION TO SAFETY
11 - J
IB HEAD ELECTROVALVE
Enables use of two hydraulic functions on the attachment circuit.
NOTE : Certain jib head electrovalves have a decompression button 1 for quick connection of easy-fit connectors.
FUNCTIONING
MT 845 Série 2 + Turbo
MT 940/1240 L Série 2 + Turbo
MT 1233 S Série 2 + Turbo
MT 1330/1337 SL Série 2 + Turbo
- Button 2 not engaged, the lever controls a hydraulic function.
- Pressing button 2, the lever controls another hydraulic function.
2
FUNCTIONING
MT 845 Turbo MONO-ULTRA Série 2
MT 940/1240 L Turbo MONO-ULTRA Série 2
MT 1233 S Turbo MONO-ULTRA Série 2
MT 1337 SL Turbo MONO-ULTRA Série 2
- When pressing the button 3, the lever to the right or to the left controls one hydraulic function.
- When pressing the button 4, the lever to the right or to the left controls another hydraulic function.
1st ASSEMBLY
4
3
2nd ASSEMBLY
3
4
1
2 - 64
INTRODUCTION TO SAFETY
12 - J
I B H E A D E L E C T R OVA LV E
+
P R E A R R A N G E D H Y D R AU L I C
ATTACHMENT LOCKING
The addition of these two options enables the combining of several hydraulic functions.
13 - N/A
C
UT
-
OFF OF
"S
IMPLE
"
OR
"W
ORSENING
"
HYDRAULIC MOVEMENTS
Up to machine Nr : 147615
The switch 1 enables the cut-off of "SIMPLE" or "WORSENING" hydraulic movements to be used or not.
OPERATION
THE SWITCH 1 IN POSITION A (LAMP SWITCHED ON) :
With no cut-off of "SIMPLE" or "WORSENING" hydraulic movements so as to carry out for example earth work.
Only the red signal light C indicates that the lift truck reaches 100 % of the maximum authorized load.
No cut-off of the hydraulic movements.
The sound alarm is disconnected.
C
B
A
1
See operator’s manual for the operation and description of this option.
THE SWITCH 1 IN POSITION B (LAMP SWITCHED OFF) :
With cut-off of "SIMPLE" or "WORSENING" hydraulic movements.
The red signal light C indicates that the lift truck reaches 100 % of the maximum authorized load and that all the hydraulic movements are neutralised.
The sound alarm goes off at the same time as the red signal light C.
CUT-OFF OF "SIMPLE" HYDRAULIC MOVEMENTS
To restart the hydraulic movements, proceed as follows :
- Place the switch 1 into position A.
- Carry out the positive hydraulic movements in the following order ; Lifting and retracting of the jib.
- Replace the switch 1 into position B.
CUT-OFF OF "WORSENING" HYDRAULIC MOVEMENTS
To restart the hydraulic controls, carry out the positive hydraulic movements (Lifting and retracting the jib).
NOTE : When the jib is retracted, the function cut-off of "SIMPLE" or "WORSENING" hydraulic movements is disconnected.
2 - 65
INTRODUCTION TO SAFETY
13 - N/A
C
UT OUT
"S
IMPLE
"
OR
"A
GGRAVATING
"
HYDRAULIC MOVEMENTS
From machine Nr : 147616
Switch 1 enables or disables the "SIMPLE" or "AGGRAVATING" hydraulic movement cut out device.
OPERATION
SWITCH 1 TO POSITION A (INDICATOR LAMP ON) :
The "SIMPLE" or "AGGRAVATING" hydraulic movement cut out device is disabled, e.g.
for earth moving works.
Only the visual alarm C is in operation to indicate the load status.
C1 - 4 green leds : The lift truck is operating in perfect safety.
C2 - 2 yellow leds : The lift truck is approaching the maximum rated load.
C3 - 1 red led : The lift truck has reached the maximum rated load.
C4 - 1 red led : The lift truck is overloaded.
1
B
A
C1
C1
C1
C4
C3
C2
C2
C1
C
No cut-out of hydraulic movements.
The buzzer is disconnected.
See instruction manual for a description and utilization of this option.
SWITCH 1 TO POSITION B (INDICATOR LAMP OFF) :
With cut out "SIMPLE" or "AGGRAVATING" hydraulic movements.
Leds C4 and C3 indicate that the lift truck has reached 100% of the maximum rated load and all hydraulic movements have been neutralized.
The buzzer is simultaneously set off.
CUT OUT "SIMPLE" HYDRAULIC MOVEMENTS
To recover the hydraulic controls, proceed as follows :
- Turn switch 1 to position A.
- Carry out the positive hydraulic movements in the following order : raise and retract the jib.
- Turn switch 1 to position B.
CUT OUT "AGGRAVATING" HYDRAULIC MOVEMENTS
To recover the hydraulic controls carry out the positive hydraulic movements (Raise and retract the jib).
NOTE : When the jib is retracted, the "SIMPLE" or "AGGRAVATING" hydraulic movement cut out function is disabled.
2 - 66
INTRODUCTION TO SAFETY
14 - P
REARRANGED TRAILER LOCKING
Enables the hydraulic connection of a braked trailer (See chapter : TOWING PIN AND
HOOK in paragraph : 2 - DESCRIPTION).
OPERATION
- Connect the trailer braking hose onto the rear braking coupling.
- Press the switch 1 into lower position (Lamp lighted up) so as to set into operation the trailer braking.
When using a braked trailer, the hose must be connected and the switch 1 switched on. When not using a braked trailer, the switch 1 must necessarily be switched off.
15 - P
REARRANGED HYDRAULIC CONTROL REAR SINGLE OR DOUBLE
EFFECT
Enables the use of a hydraulic rear hook or of a trailer with hydraulic tipping.
- Single or double effect rear hydraulic control functions with hydraulic control of the additional accessory (See chapter : 21 - HYDRAULIC CONTROLS in paragraph : 2 -
DESCRIPTION) according to the position of tap 1.
- Position A : Hydraulic control of the additional accessory at the front of the lift truck.
- Position B : Hydraulic control of the additional accessory at the rear of the lift truck.
1
A
1
B
2 - 67
INTRODUCTION TO SAFETY
2 - 68
INTRODUCTION TO SAFETY
3 - 1
INTRODUCTION TO SAFETY
3 - 2
INTRODUCTION TO SAFETY
FILTERS CARTRIDGES AND BELTS
MT 845 Série 2 + Turbo + Turbo MONO-ULTRA
MT 940 L Série 2 + Turbo + Turbo MONO-ULTRA
1 2 3 4 5 6 7 8 9 10
11 12
DESIGNATION
1 - Engine oil filter
MT 845 Série 2
MT 940 L Série 2
MT 845 Turbo Série 2 + MONO-ULTRA
MT 940 L Turbo Série 2 + MONO-ULTRA
2 - Dry air filter cartridge
3 - Safety dry air filter cartridge
4 - Transmission oil filter
5 - Fuel filter cartridge
6 - Hydraulic return oil filter cartridge
7 - Suction strainer for hydraulic oil tank
8 - Filter cap for hydraulic oil tank
9 - Alternator belt
10 - Fan belt
Up to machine Nr : 143987
From machine Nr : 143988 and up to machine Nr : 170837
From machine Nr : 170838
11 - Cyclonic pre-filter (As assembly)
12 - Automatic vacuum-cleaning pre-filter
PART NUMBER
133755
133755
476954
476954
563416
563415
561749
49660
221174
77402
62415
563270
223258
229300
238795
224713
226611
CLEAN
50 H *
1000 H
10 H
CHANGE
500 H
500 H
500 H
500 H
500 H *
1000 H *
500 H
500 H
500 H
1000 H
* : This periodicity is given for information only (See chapter : SERVICING SCHEDULE in paragraph : 3 - MAINTENANCE) for cleaning and changing.
3 - 3
INTRODUCTION TO SAFETY
MT 1233 S Série 2 + Turbo + Turbo MONO-ULTRA
MT 1240 L Série 2 + Turbo + Turbo MONO-ULTRA
MT 1330 SL Série 2 + Turbo
MT 1337 SL Série 2 + Turbo + Turbo MONO-ULTRA
1 2 3 4 5 6 7 8 9 10
11 12
DESIGNATION
1 - Engine oil filter
MT 1233 S Série 2
MT 1240 L Série 2
MT 1330/1337 SL Série 2
MT 1233 S Turbo Série 2 + MONO-ULTRA
MT 1240 L Turbo Série 2 + MONO-ULTRA
MT 1330 SL Turbo Série 2
MT 1337 SL Turbo Série 2 + MONO-ULTRA
2 - Dry air filter cartridge
3 - Safety dry air filter cartridge
4 - Transmission oil filter
5 - Fuel filter cartridge
6 - Hydraulic return oil filter cartridge (Qty 2)
7 - Suction strainer for hydraulic oil tank
8 - Filter cap for hydraulic oil tank
9 - Alternator belt
10 - Fan belt
Up to machine Nr : 143987
From machine Nr : 143988 and up to machine Nr : 170837
From machine Nr : 170838
11 - Cyclonic pre-filter (As assembly)
12 - Automatic vacuum-cleaning pre-filter
PART NUMBER CLEAN
133755
133755
133755
476954
476954
476954
476954
563416
563415
561749
49660
221174
19910
62415
563270
223258
229300
238795
224713
226611
50 H *
1000 H
10 H
1000 H
* : This periodicity is given for information only (See chapter : SERVICING SCHEDULE in paragraph : 3 - MAINTENANCE) for cleaning and changing.
CHANGE
500 H
500 H
500 H
500 H
500 H
500 H
500 H
500 H *
1000 H *
500 H
500 H
500 H
3 - 4
INTRODUCTION TO SAFETY
MT 1637 SL Série 2 + Turbo + Turbo MONO-ULTRA
MT 1740 SL Série 2 + Turbo
1 2 3 4 5 6 7 8 9 10
11 12
DESIGNATION
1 - Engine oil filter
MT 1637 SL Série 2
MT 1740 SL Série 2
MT 1637 SL Turbo Série 2 + MONO-ULTRA
MT 1740 SL Turbo Série 2
2 - Dry air filter cartridge
3 - Safety dry air filter cartridge
4 - Transmission oil filter
5 - Fuel filter cartridge
6 - Hydraulic return oil filter cartridge (Qty 2)
7 - Suction strainer for hydraulic oil tank
8 - Filter cap for hydraulic oil tank
9 - Alternator belt
10 - Fan belt
Up to machine Nr : 143987
From machine Nr : 143988 and up to machine Nr : 170837
From machine Nr : 170838
11 - Cyclonic pre-filter (As assembly)
12 - Automatic vacuum-cleaning pre-filter
PART NUMBER
133755
133755
476954
476954
563416
563415
561749
49660
221174
77402
62415
563270
223258
229300
238795
224713
226611
CLEAN
50 H *
1000 H
10 H
CHANGE
500 H
500 H
500 H
500 H
500 H *
1000 H *
500 H
500 H
500 H
1000 H
* : This periodicity is given for information only (See chapter : SERVICING SCHEDULE in paragraph : 3 - MAINTENANCE) for cleaning and changing.
3 - 5
INTRODUCTION TO SAFETY
LUBRICANTS AND FUEL
I.C. ENGINE
COMPONENT
I.C. ENGINE
COOLING CIRCUIT
CAPACITY
7,75 Liters
RECOMMENDATION
Shell: Rotella 15w40
Citgo: C-600 15w40
23,5 Liters Tulco 50/50 premix anti-freeze
FUEL TANK
TRANSMISSION
COMPONENT
TRANSMISSION
ANGLE GEAR BOX
TRANSMISSION UNIVERSAL JOINT
JIB
COMPONENT
JIB PADS
GREASING OF THE JIB
HYDRAULICS
COMPONENT
HYDRAULIC OIL TANK
MT 845 Série 2 + Turbo + Turbo MONO-ULTRA
MT 940 L Série 2 + Turbo + Turbo MONO-ULTRA
MT 1233 S Série 2 + Turbo + Turbo MONO-ULTRA
MT 1240 L Série 2 + Turbo + Turbo MONO-ULTRA
MT 1330 SL Série 2 + Turbo
MT 1337 SL Série 2 + Turbo + Turbo MONO-ULTRA
MT 1637 SL Série 2 + Turbo + Turbo MONO-ULTRA
MT 1740 SL Série 2 + Turbo
BRAKE
COMPONENT
BRAKE CIRCUIT
CAB
COMPONENT
CAB DOOR
WINDSCREEN WASHER TANK
135 Liters
CAPACITY
126 Liters
126 Liters
126 Liters
175 Liters
175 Liters
Diesel fuel (*)
CAPACITY RECOMMENDATION
9,4 Liters Shell: Donax TG Dexron III
Citgo: Transgard ATF Dexron III
2,25 Liters Shell: Spirax DH 80w90
Citgo: Premium Gear MP 80w90
Shell: Rentinax Am
Citgo: Lithoplex CM-2
RECOMMENDATION
Shell: Rentinax Am
Citgo: Lithoplex CM-2
Shell: Rentinax Am
Citgo: Lithoplex CM-2
RECOMMENDATION
Shell: Tellus T46
120 Liters Citgo: Transgard THF Lo-Temp
120 Liters
126 Liters
RECOMMENDATION
Shell: Donax TG Dexron III
Citgo: Transgard ATF Dexron III
RECOMMENDATION
Windscreen washer fluid
3 - 6
INTRODUCTION TO SAFETY
FRONT AND REAR AXLES (Up to machine Nr : 147615)
COMPONENT
FRONT AXLE DIFFERENTIAL
REAR AXLE DIFFERENTIAL
FRONT WHEELS REDUCERS
CAPACITY RECOMMENDATION
7,3 Liters Shell: Donax TD
Citgo: Transgard Tractor Hyd Fluid
7,3 Liters Shell: Donax TD
Citgo: Transgard Tractor Hyd Fluid
1,65 Liter Shell: Spirax DH 80w90
Citgo: Premium Gear MP 80w90
REAR WHEELS REDUCERS 1,65 Liter Shell: Spirax DH 80w90
Citgo: Premium Gear MP 80w90
FRONT AND REAR WHEELS REDUCERS PIVOTS
REAR AXLE OSCILLATION
FRONT AXLE OSCILLATION
Shell: Rentinax Am
Citgo: Lithoplex CM-2
Shell: Rentinax Am
Citgo: Lithoplex CM-2
Shell: Rentinax Am
Citgo: Lithoplex CM-2
FRONT AND REAR AXLES (From machine Nr : 147616)
COMPONENT
FRONT AXLE DIFFERENTIAL
REAR AXLE DIFFERENTIAL
FRONT WHEELS REDUCERS
CAPACITY
7 Liters
RECOMMENDATION
Shell: Donax TD
Citgo: Transgard Tractor Hyd Fluid
7 Liters Shell: Donax TD
Citgo: Transgard Tractor Hyd Fluid
0,65 Liter Shell: Spirax DH 80w90
Citgo: Premium Gear MP 80w90
REAR WHEELS REDUCERS 0,65 Liter Shell: Spirax DH 80w90
Citgo: Premium Gear MP 80w90
FRONT AND REAR WHEELS REDUCERS PIVOTS
REAR AXLE OSCILLATION
FRONT AXLE OSCILLATION
Shell: Rentinax Am
Citgo: Lithoplex CM-2
Shell: Rentinax Am
Citgo: Lithoplex CM-2
Shell: Rentinax Am
Citgo: Lithoplex CM-2
CHASSIS
TILTING CORRECTER
STABILIZERS
COMPONENT RECOMMENDATION
Shell: Rentinax Am
Citgo: Lithoplex CM-2
Shell: Rentinax Am
Citgo: Lithoplex CM-2
USE THE RECOMMENDED LUBRICANTS :
- For topping up, oils do not necessarily have to be miscible.
- For oil changes, MANITOU oils are perfectly suitable.
DIAGNOSTIC ANALYSIS OF OIL
In the event of a maintenance or service contract with the dealer you may be requested to provide a sample of a selected component's oil, for diagnostic analysis.
3 - 7
INTRODUCTION TO SAFETY
(*) FUEL SPECIFICATION
CETANE RATING : 45 minimum
VISCOSITY
DENSITY
: 2 - 4,5 Centistokes at 40° C
: 0,820 - 0,860 kg/litre
SULPHUR
DISTILLATION
: 0,2 % mass maximum
: 85 % at 350° C
- The cetane rating is a measure of the ignition quality of a diesel fuel. A fuel with a low cetane index may cause problems with cold starts and affect combustion.
- Viscosity is the resistance to flow. If the viscosity is outside the limits, I.C. engine performance may be affected.
- A low density reduces the power of the I.C. engine, a high density increases the power of the I.C. engine and the exhaust fumes.
- A high sulphur content (Not usually found in europe, north america or australasia) may cause wear to the I.C. engine. If only fuels with a high sulphur content are available, it is necessary to use a highly alkaline greasing oil in the I.C. engine or to replace the greasing oil more frequently.
- Distillation : this indicates the mixture of different hydrocarbons in the fuel. A high ratio of light hydrocarbons can affect the characteristics of combustion.
- Fuels for low temperatures : special winter fuels may be available for use in the I.C. engine at temperatures below 0°C.
These fuels have a lower viscosity and thus reduce the formation of paraffin in the fuel at low temperatures. The formation of paraffin can prevent filtration of the fuel.
3 - 8
INTRODUCTION TO SAFETY
3 - 9
INTRODUCTION TO SAFETY
SERVICING SCHEDULE
A = AJUST
C = CHECK
D = DESCALE
G = GREASE
N = CLEAN
P = BLEED
R = CHANGE
V = DRAIN
I.C. ENGINE
I.C. engine oil level . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cooling liquid level . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cyclonic prefilter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dry air filter cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . .
Radiator core . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fan belt tension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alternator/crankshaft belt tension . . . . . . . . . . . . . . . . .
I.C. engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I.C. engine oil filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel filter cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel feed pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Blanking cap on the induction manifold . . . . . . . . . . . . .
Fuel tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety dry air filter cartridge . . . . . . . . . . . . . . . . . . . . . .
I.C. engine silent blocks . . . . . . . . . . . . . . . . . . . . . . . . .
I.C. engine rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Valves clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cooling liquid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Radiator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water pump and the thermostat . . . . . . . . . . . . . . . . . .
Alternator and the starter motor . . . . . . . . . . . . . . . . . . .
Turbocompressor (Only for the "Turbo") . . . . . . . . . . . . . . .
Bleed the fuel system . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRANSMISSION
Transmission oil level . . . . . . . . . . . . . . . . . . . . . . . . . . .
Angle gear box oil level . . . . . . . . . . . . . . . . . . . . . . . . .
Transmission oil filter . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transmission oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transmission housing strainer . . . . . . . . . . . . . . . . . . . .
Angle gear box oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transmission silent blocks . . . . . . . . . . . . . . . . . . . . . . .
Transmission controls . . . . . . . . . . . . . . . . . . . . . . . . . .
Transmission pressures . . . . . . . . . . . . . . . . . . . . . . . . .
Converter pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TYRES
Tyres pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel nuts torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Condition of wheels and tyres . . . . . . . . . . . . . . . . . . . .
Change a wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
JIB
Jib pads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jib . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jib pads wear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Condition of jib unit . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bearings and articulation rings . . . . . . . . . . . . . . . . . . . .
After the first 50 hours
Day or
10 hours
50 hours
250 hours
1 year or
500 hours
1 year or
1000 hours
2000 hours
4000 hours
A
A
V
R
R
C**
R
V
V
C
C
C
N
C
C
C
G*
N
N
C
G
A
A
C
R
V
R
R
N
C
R
N
R
C**
C**
C**
V
N
V
C**
C**
C**
C**
V
N/D**
C**
C**
C**
C**
C**
C**
C**
HYDRAULICS
Hydraulic oil level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic return oil filter cartridge . . . . . . . . . . . . . . . . .
Balancing valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Suction strainer for hydraulic oil tank . . . . . . . . . . . . . . .
Filter cap for hydraulic oil tank . . . . . . . . . . . . . . . . . . . .
Speeds of hydraulic movements . . . . . . . . . . . . . . . . . .
Hydraulic pump pipe filter . . . . . . . . . . . . . . . . . . . . . . .
Condition of hoses and flexibles pipes . . . . . . . . . . . . . .
Condition of cylinders (leakage, shafts) . . . . . . . . . . . . .
Hydraulic circuit pressures . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic circuit outputs . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic oil tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
R
C
C
R
C
V
N
R
C**
N**
C**
C**
C**
C**
N**
PAGE
3-12
3-12
3-12
3-13
3-16/3-29
3-16
3-16
3-24
3-24
3-28
3-28
3-29
3-30
3-34
3-36
3-36
3-42
3-44
3-13
3-25
3-30
3-37
3-37
3-38
3-13
3-13
3-45
3-14
3-16
3-19
3-31
3-31
3-39
3-39
3-39
3 - 10
INTRODUCTION TO SAFETY
A = AJUST
C = CHECK
D = DESCALE
G = GREASE
N = CLEAN
P = BLEED
R = CHANGE
V = DRAIN
BRAKE
Brake oil level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking brake mechanism . . . . . . . . . . . . . . . . . . . . . . .
Brake oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake circuit pressure . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CAB
Windscreen washer liquid level . . . . . . . . . . . . . . . . . . .
Cab door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Seat belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Condition of the rear view mirrors . . . . . . . . . . . . . . . . .
Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
After the first 50 hours
Day or
10 hours
50 hours
250 hours
1 year or
500 hours
1 year or
1000 hours
2000 hours
4000 hours
C
C
G
A
G
V**
P**
C**
A**
C
C**
C**
ELECTRICITY
Battery electrolyte level . . . . . . . . . . . . . . . . . . . . . . . . .
Battery electrolyte density . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Condition of wiring harness and cables . . . . . . . . . . . . .
Lights and signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warning indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjust the front headlamps . . . . . . . . . . . . . . . . . . . . . .
C
C
C**
C**
C**
FRONT AND REAR AXLES
Front wheels reducers pivots . . . . . . . . . . . . . . . . . . . . .
Rear wheels reducers pivots . . . . . . . . . . . . . . . . . . . . .
Front axle oscillation . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear axle oscillation . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transmission universal joint . . . . . . . . . . . . . . . . . . . . . .
Front axle differential oil level . . . . . . . . . . . . . . . . . . . .
Rear axle differential oil level . . . . . . . . . . . . . . . . . . . . .
Front wheels reducers oil level . . . . . . . . . . . . . . . . . . .
Rear wheels reducers oil level . . . . . . . . . . . . . . . . . . . .
Front axle differential oil . . . . . . . . . . . . . . . . . . . . . . . . .
Rear axle differential oil . . . . . . . . . . . . . . . . . . . . . . . . .
Front wheels reducers oil . . . . . . . . . . . . . . . . . . . . . . . .
Rear wheels reducers oil . . . . . . . . . . . . . . . . . . . . . . . .
Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wearing of front axle brake discs . . . . . . . . . . . . . . . . . .
Wearing of rear axle brake discs . . . . . . . . . . . . . . . . . .
Front wheels reducers universal joint . . . . . . . . . . . . . .
Rear wheels reducers universal joint . . . . . . . . . . . . . . .
Steering swivel joints . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front wheels reducers clearance . . . . . . . . . . . . . . . . . .
Rear wheels reducers clearance . . . . . . . . . . . . . . . . . .
CHASSIS
Tilting corrector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stabilizers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bearings and articulation rings . . . . . . . . . . . . . . . . . . . .
ATTACHMENTS
Forks wear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attachment carriage . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Condition of attachments . . . . . . . . . . . . . . . . . . . . . . . .
LIFT TRUCK
Tow the lift truck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sling the lift truck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transport the lift truck on a platform . . . . . . . . . . . . . . .
V
V
V
V
G
G
G
G
G
G
G
C
C
C
C
V
V
C**
V
V
C**
C**
C**
G/C**
G/C**
C**
C**
G/C**
G/C**
G/C**
C**
C**
C**
C**
C**
C**
C**
(*) : Every 10 hours during the first 50 hours, then once at 250 hours.
(**) : Consult your dealer.
3-19
3-25
3-32
3-20
3-20
3-40
3-20
3-32
3-48
3-21
3-21
3-21
3-21
3-21
3-26
3-26
3-27
3-27
3-33
3-33
3-40
3-40
3-22
3-22
3-46
3-46
3-47
3 - 11
INTRODUCTION TO SAFETY
A - DAILY OR EVERY 10 HOURS SERVICE
A1 - I.C.
ENGINE OIL LEVEL
CHECK
Place the lift truck on level ground with the I.C. engine stopped, and let the oil drain into the sump.
- Open the I.C. engine bonnet.
- Remove the dipstick 1 (Fig. A1).
- Clean the dipstick and check the level between the two MAXI and MINI notches.
- If necessary, add oil (See chapter : LUBRICANTS AND FUEL in paragraph : 3 -
MAINTENANCE) by the filler port 2 (Fig. A1).
A1
2
A2 - C
OOLING LIQUID LEVEL
CHECK
Place the lift truck on level ground with the I.C. engine stopped, and allow the I.C.
engine to cool.
- Open the I.C. engine bonnet.
- Slowly turn the cap of the radiator 1 (Fig. A2) anticlockwise up to the safety stop.
- Allow the pressure and vapour to escape.
- Press down and turn the cap so as to release the cap.
- If necessary, add cooling liquid (See chapter : LUBRICANTS AND FUEL in paragraph :
3 - MAINTENANCE) in order to top up the level to 12 mm below the filler port 2 (Fig.
A2).
- Lubricate slightly the filler neck in order to facilitate the setting and the removal of the radiator cap.
If the cooling liquid is very hot, add only hot cooling liquid (80°C). In an emergency, you can use water as a cooling liquid, then change the cooling circuit liquid as soon as possible (See chapter : F1 - COOLING LIQUID in paragraph : 3 - MAINTENANCE).
A3 - F
UEL LEVEL
CHECK
Keep the fuel tank full, to reduce as much as possible any condensation due to the atmospheric conditions.
- Open the access panel for fuel filling.
- Remove cap 1 (Fig. A3) and set it on its bracket.
- Fill the fuel tank with clean fuel (See chapter : LUBRICANTS AND FUEL in paragraph :
3 - MAINTENANCE), filtered through a strainer or a clean, lint free cloth, through filler port 2 (Fig. A3).
- Put the cap back 1 (Fig. A3) and close the access panel for fuel filling.
Never smoke or approach with a flame during filling operations or when the tank is open. Never refill while engine is running.
The fuel tank is degassed via the filler plug. When changing it, always use an original part, with degassing hole.
1
A2
2
A3
1
2
1
3 - 12
INTRODUCTION TO SAFETY
A4 - C
YCLONIC PREFILTER
CLEAN
The cleaning interval is given as a guide, however the prefilter must be emptied as soon as impurities reach the MAXI level on the tank.
- Loosen nut 1 (Fig. A4), remove cover 2 (Fig. A4) and empty the tank.
- Clean the prefilter unit with a clean dry cloth and reassemble the unit.
When cleaning, take care not to let impurities into the dry air filter.
A4
1
2
A5 - T
RANSMISSION OIL LEVEL
CHECK
The level of transmission oil can be checked with the I.C. engine idling or stopped, according to the type of dipstick.
LEVEL OF OIL WITH I.C. ENGINE IDLING (1st Assembly)
• Identification on dipstick :
MIN MAX
- Park the lift truck on level ground with the jib raised, the I.C. engine cold and idling.
LEVEL OF OIL WITH I.C. ENGINE STOPPED (2nd Assembly)
• Identification on dipstick :
MIN MAX MOTOR STOP
- Park the lift truck on level ground with the jib raised, the I.C. engine cold and stopped.
Carry out the control within 5 minutes of the i.c. engine being stopped.
- Remove the plastic cap 1 (Fig. A5).
- Remove the dipstick 2 (Fig. A5).
- Wipe the dipstick and check the correct level between the two MIN and MAX marks.
- If necessary, add oil (See chapter : E3 - TRANSMISSION OIL in paragraph : 3 -
MAINTENANCE).
A6 - T
YRES PRESSURE AND WHEEL NUTS TORQUE
CHECK
- Check the condition of the tyres, to detect cuts, protuberances, wear, etc.
- Check the torque load of the wheel nuts (See fig. A6). Non compliance with this instruction can cause damage and rupture to the wheel bolts and distortion to the wheels.
- Check and adjust the tyre pressures if necessary (See chapter : CHARACTERISTICS paragraph : 2 - DESCRIPTION).
Check that the air hose is correctly connected to the tyre valve before inflating and keep all persons at a distance during inflation. Respect the recommended tyre pressures given.
A5
1
2
A6
WHEEL NUTS
TIGHTENING TORQUE
FRONT TYRES
630 ± 15 %
N.m
REAR TYRES
630 ± 15 %
N.m
3 - 13
INTRODUCTION TO SAFETY
A7 - J
IB PADS
CLEAN - GREASE
To be carried out every 10 hours during the first 50 hours service, then once at 250 hours.
- Extend the jib completely.
- With a brush, apply a coat of grease (See chapter : LUBRICANTS AND FUEL in paragraph : 3 - MAINTENANCE) on the 4 sides of the telescope(s) (Fig. A7).
- Telescope the jib several times in order to spread the coat of grease evenly.
- Remove the surplus of grease.
If the lift truck is used in an abrasive environment (Dust, sand, coal…) Use lubricating varnish (MANITOU Reference : 483 536). In this respect, consult your dealer.
NOTE : MT 845 Série 2 + Turbo + Turbo MONO-ULTRA
MT 940 L Série 2 + Turbo + Turbo MONO-ULTRA
MT 1233 S Série 2 + Turbo + Turbo MONO-ULTRA
MT 1240 L Série 2 + Turbo + Turbo MONO-ULTRA
MT 1330 SL Série 2 + Turbo
MT 1337 SL Série 2 + Turbo + Turbo MONO-ULTRA
A jib sealing kit is available as an OPTION.
A7
3 - 14
INTRODUCTION TO SAFETY
3 - 15
INTRODUCTION TO SAFETY
B - EVERY 50 HOURS SERVICE
Carry out the operations described previously as well as the following operations.
B1 - D
RY AIR FILTER CARTRIDGE
CHECK - CLEAN
In case of use in a heavily dust laden atmosphere, there are pre-filtration cartridges (See chapter : FILTERS CARTRIDGES
AND BELTS in paragraph : 3 - MAINTENANCE). Also, the checking and cleaning periodicity of the cartridge must be reduced.
If the clogging indicator light comes on, this operation must be carried out as quickly as possible (1 hour maximum). The cartridge must not be cleaned more than seven times, after which the cartridge must be changed.
- For the disassembly and reassembly of the cartridge, see chapter : D3 - DRY AIR FILTER CARTRIDGE in paragraph : 3 -
MAINTENANCE.
- Clean the filter cartridge using a compressed air jet (Max. pressure 3 bar) directed from the top to the bottom and from the inside towards the outside at a minimum distance of 30 mm from the cartridge wall.
- Cleaning is completed when there is no more dust on the cartridge.
Respect the safety distance of 30 mm between the air jet and the cartridge to avoid tearing or making a hole in the cartridge.
The cartridge must not be blown anywhere near the air filter box. Never clean the cartridge by tapping it against a hard surface. Your eyes must be protected during this intervention.
- Clean the cartridge seal surfaces with a damp, clean lint-free cloth and grease with a silicone lubricant (MANITOU Reference :
479 292).
Do not clean the dry air filter cartridge by washing it in liquid. Do not clean by any means the safety cartridge located inside the filter cartridge, change it for a new one if it is dirty or damaged.
B2 - R
ADIATOR CORE
CLEAN
- Open the I.C. engine bonnet.
In order to prevent the radiator becoming clogged, clean the radiator with a compressed air jet directed from inside to outside.
This is the only way to clean the core of debris.
When handling straw, grain or cereal, clean the radiator core daily. Do not use water jet or high pressure steam as this could damage the radiator fins.
B3 - F
UEL FILTER
CHECK
- Open the I.C. engine bonnet.
- Visually check for the presence of water in tank 1 (Fig. B3) and drain if necessary.
- Place a receptacle under the tank and loosen drain plug 2 (Fig. B3) by two of three turns.
- Leave the diesel fuel to flow out until it is free from impurities and water.
- Tighten the drain plug while the diesel fuel is running out.
1
B3
2
B4 - J
IB
GREASE
To be carried out weekly, if the lift truck has been operated for less than 50 hours during the week.
In the event of prolonged use in an extremely dusty or oxidising atmosphere, reduce this interval to 10 working hours or every day.
3 - 16
INTRODUCTION TO SAFETY
Clean and lubricate the following points with grease (See chapter : LUBRICANTS AND FUEL in paragraph : 3 -
MAINTENANCE) and remove the surplus of grease.
MT 845 Série 2 + Turbo + Turbo MONO-ULTRA
MT 940 L Série 2 + Turbo + Turbo MONO-ULTRA
1 - Lubricators of the jib axle (2 lubricators) (Fig. B4/1).
2 - Lubricators of the carriage axle (2 lubricators) (Fig. B4/2).
3 - Lubricator of the tilt cylinder foot axle (1 lubricator) (Fig. B4/3).
4 - Lubricator of the tilt cylinder head axle (1 lubricator) (Fig. B4/4).
5 - Lubricators of the carriage connecting rod axle (3 lubricators) (Fig. B4/2 and B4/5).
6 - Lubricators of the lifting cylinders foot axle (2 lubricators) (Fig. B4/6).
7 - Lubricators of the lifting cylinders head axle (2 lubricators) (Fig. B4/7).
8 - Lubricators of the compensation cylinders foot axle (2 lubricators) (Fig. B4/8).
9 - Lubricators of the compensation cylinders head axle (2 lubricators) (Fig. B4/9).
B4/1 B4/2 B4/3
5
3
1
1
2
2
B4/4
4
B4/5
5
5
B4/6
6
B4/7 B4/8
8
B4/9
9 9
7 7
3 - 17
INTRODUCTION TO SAFETY
MT 1233 S Série 2 + Turbo + Turbo MONO-ULTRA
MT 1240 L Série 2 + Turbo + Turbo MONO-ULTRA
MT 1330 SL Série 2 + Turbo
MT 1337 SL Série 2 + Turbo + Turbo MONO-ULTRA
MT 1637 SL Série 2 + Turbo + Turbo MONO-ULTRA
MT 1740 SL Série 2 + Turbo
10 - Lubricators of the jib axle (2 lubricators) (Fig. B4/10).
11 - Lubricators of the carriage axle (2 lubricators) (Fig. B4/11).
12 - Lubricator of the tilt cylinder foot axle (1 lubricator) (Fig. B4/12).
13 - Lubricator of the tilt cylinder head axle (1 lubricator) (Fig. B4/13).
14 - Lubricators of the lifting cylinder foot axle (2 lubricators) (Fig. B4/14).
15 - Lubricators of the lifting cylinder head axle (2 lubricators) (Fig. B4/15).
16 - Lubricators of the compensation cylinder foot axle (2 lubricators) (Fig. B4/16).
17 - Lubricators of the compensation cylinder head axle (2 lubricators) (Fig. B4/17).
B4/10 B4/11
10
10
11 11
B4/14
14
13
B4/13
15
B4/12
12
B4/15
15
B4/16
16
B4/17
17 17
3 - 18
INTRODUCTION TO SAFETY
B5 - H
YDRAULIC OIL LEVEL
CHECK
Place the lift truck on level ground with the I.C. engine stopped, and the jib retracted and lowered as far as possible.
- Refer to gauge 1 (Fig. B5/1).
- The oil level is correct when it is at the level of the red point.
- If necessary, add oil (See chapter : LUBRICANTS AND FUEL in paragraph : 3 -
MAINTENANCE).
- Open the access panel for hydraulic oil filling.
- Remove cap 2 (Fig. B5/2).
- Add oil by filler port 3 (Fig. B5/2).
Use a clean funnel and clean the underside of the oil drum before filling.
- Put the cap back and close the access panel for hydraulic oil filling.
Always maintain the oil level at maximum as cooling depends on the oil flowing through the tank.
2
1
B5/1
B5/2
3
B6 - B
RAKE OIL LEVEL
CHECK
Place the lift truck on level ground.
- Loosen screws 1 (Fig. B6/1) and remove the access panel for braking oil tank 2 (Fig.
B6/1).
- The level is correct when it is at the MAXI level on the tank.
- If necessary, add oil (See chapter : LUBRICANTS AND FUEL in paragraph : 3 -
MAINTENANCE) by the filler port 3 (Fig. B6/2).
If the braking oil level is abnormally low, consult your dealer.
B6/1
2
1
1
3
B6/2
3 - 19
INTRODUCTION TO SAFETY
B7 - W
INDSCREEN WASHER LIQUID LEVEL
CHECK
- Remove filler cap 1 (Fig. B7).
- Check visually the level.
- If necessary add windscreen washer liquid (See chapter : LUBRICANTS AND FUEL in paragraph : 3 - MAINTENANCE) by filler port 2 (Fig. B7).
1
2
B7
B8 - C
AB DOOR
GREASE
Clean and lubricate the points 1 (4 lubricators) (Fig. B8) with grease (See chapter :
LUBRICANTS AND FUEL in paragraph : 3 - MAINTENANCE) and remove the surplus of grease.
B8
1
1
B9 - B
ATTERY ELECTROLYTE LEVEL
CHECK
Check the electrolyte level in each cell of the battery.
If the lift truck is working in a high temperature environment, check the level more frequently than every 50 hours service.
- Open the I.C. engine bonnet.
- Open battery cowl 1 (Fig. B9/1) and hold it open with locking device 2 (Fig. B9/1).
- Remove caps 3 (Fig. B9/2) from each cell of the battery.
- The level is correct when it is 1,5 cm above the top of the plates in the battery.
- If necessary, top up the cells with clean distilled water that has been stored in a glass container.
- Clean and dry caps 3 (Fig. B9/2) and refit in place and screw in firmly.
- Check the terminal connections and lightly smear them with petroleum jelly to prevent the formation of verdigris.
- Close the battery cowl.
Handling and servicing a battery can be dangerous, take the following precautions :
- Wear protective goggles.
- Keep the battery horizontal.
- Never smoke or work near a naked flame.
- Work in a well-ventilated area.
- In the event of electrolyte being spilled onto the skin or splashed in the eyes, rinse thoroughly with cold water for 15 minutes and call a doctor.
3 - 20
3
B9/1
1
B9/2
2
INTRODUCTION TO SAFETY
B10 - F
RONT AND REAR WHEELS REDUCERS PIVOTS
GREASE
Clean and lubricate the points 1 (8 lubricators) (Fig. B10) with grease (See chapter :
LUBRICANTS AND FUEL in paragraph : 3 - MAINTENANCE) and remove the surplus of grease.
B10
1
B11 - F
RONT AXLE OSCILLATION
GREASE
MT 940/1240 L Série 2 + Turbo + Turbo MONO-ULTRA
MT 1330/1740 SL Série 2 + Turbo
MT 1337/1637 SL Série 2 + Turbo + Turbo MONO-ULTRA
Clean and lubricate the points 1 (2 lubricators) (Fig. B11) with grease (See chapter :
LUBRICANTS AND FUEL in paragraph : 3 - MAINTENANCE) and remove the surplus of grease.
B11
1
B12 - R
EAR AXLE OSCILLATION
GREASE
Clean and lubricate the points 1 (2 lubricators) (Fig. B12) with grease (See chapter :
LUBRICANTS AND FUEL in paragraph : 3 - MAINTENANCE) and remove the surplus of grease.
B13 - T
RANSMISSION UNIVERSAL JOINT
GREASE
Clean and lubricate the following points with grease (See chapter : LUBRICANTS AND
FUEL in paragraph : 3 - MAINTENANCE) and remove the surplus of grease.
B13/1
Transmission / Front axle (3 lubricators)
(Fig. B13/1).
Transmission / Rear axle (3 lubricators)
(Fig. B13/2).
3 - Lubricators of the universal joint I.C.
engine / Angle gear box (2 lubricators)
(Fig. B13/3).
1
1
1
1
B12
1
3 - 21
INTRODUCTION TO SAFETY
2
2
B13/2
2
3
B13/3
3
B14 - T
ILTING CORRECTOR
GREASE
MT 940/1240 L Série 2 + Turbo + Turbo MONO-ULTRA
MT 1330/1740 SL Série 2 + Turbo
MT 1337/1637 SL Série 2 + Turbo + Turbo MONO-ULTRA
Clean and lubricate the following points with grease (See chapter : LUBRICANTS AND
FUEL in paragraph : 3 - MAINTENANCE) and remove the surplus of grease.
1 - Lubricator of the tilting corrector cylinder foot axle (1 lubricator) (Fig. B14/1).
2 - Lubricator of the tilting corrector cylinder head axle (1 lubricator) (Fig. B14/2).
1
B14/1
B14/2
B15 - S
TABILIZERS
GREASE
MT 1233 S Série 2 + Turbo + Turbo MONO-ULTRA
MT 1330/1740 SL Série 2 + Turbo
MT 1637/1337 SL Série 2 + Turbo + Turbo MONO-ULTRA
Clean and lubricate the following points with grease (See chapter : LUBRICANTS AND
FUEL in paragraph : 3 - MAINTENANCE) and remove the surplus of grease.
1 - Lubricators of the stabilizer cylinder foot axle (2 lubricators) (Fig. B15/1).
2 - Lubricators of the stabilizer cylinder head axle (2 lubricators) (Fig. B15/2).
3 - Lubricators of the stabilizer axles (2 lubricators) (Fig. B15/3).
B15/1 B15/2
2
B15/3
1
2
3 - 22
2
3
INTRODUCTION TO SAFETY
3 - 23
INTRODUCTION TO SAFETY
C - EVERY 250 HOURS SERVICE
Carry out the operations described previously as well as the following operations.
C1 - F
AN BELT TENSION
CHECK - ADJUST
- Open the I.C. engine bonnet.
- Check the belt for signs of wear and cracks and change if necessary (See chapter :
FILTERS CARTRIDGES AND BELTS in paragraph : 3 - MAINTENANCE).
- Loosen screw 1 (Fig. C1/1) on the tension pulley.
- Loosen lock nut 2 (Fig. C1/1 and C1/2) and screw 3 (Fig. C1/1 and C1/2).
- Bring the belt just into contact with pulley 4 (Fig. C1/1) (On the lift truck, check this operation by feel).
- Make a mark on the head of screw 3 (Fig. C1/1 and C1/2) and tighten, turning it 5 times.
- Tighten the lock nut 2 (Fig. C1/1 and C1/2).
- Retighten screw 1 (Fig. C1/1) on the tension pulley.
When changing the fanbelt, tighten screw 3 (Fig. C1/1 and C1/2) by one and a half turns, having allowed the I.C. engine to idle for 30 minutes.
1
2
C1/1
3
C1/2
4
3
2
C2 - A
LTERNATOR
/
CRANKSHAFT BELT TENSION
CHECK - ADJUST
- Open the I.C. engine bonnet.
- Unscrew the fastening screws 1 (Fig. C2/1).
- Lay down the protective guard 2 (Fig. C2/1).
- Check the belt for signs of wear and cracks and change if necessary (See chapter :
FILTERS CARTRIDGES AND BELTS in paragraph : 3 - MAINTENANCE).
- Check the belt tension between the pulleys of the crankshaft and of the alternator.
- Under a normal pressure exerted with the thumb (45N), the tension should be approximately 10 mm.
- Carry out adjustments if necessary.
- Untighten screws 3 (Fig. C2/2) by two to three thread turns.
- Swivel the alternator assembly so as to obtain the belt tension required.
- Retighten screws 3 (Fig. C2/2).
- Put the protective guard back 2 (Fig. C2/1).
If the alternator belt has to be changed, check the tension again after the first 20 hours of operation.
C2/1
1
1
2
1
C2/2
3
3
3 - 24
INTRODUCTION TO SAFETY
C3 - A
NGLE GEAR BOX OIL LEVEL
CHECK
Place the lift truck on level ground with the I.C. engine stopped.
- Remove the plastic cap 1 (Fig. C3).
- Remove level plug 2 (Fig. C3).
- Wipe the dipstick and check the correct level between the MINI and MAXI marks.
- If necessary, add oil (See chapter : E5 - ANGLE GEAR BOX OIL in paragraph : 3 -
MAINTENANCE).
1
C3
2
C4 - P
ARKING BRAKE
CHECK - ADJUST
Place the lift truck on a slope less than 15 % with the rated load in the transport position.
- Check the tightening adjustment by locking the parking brake in position A (Fig. C4/1).
- The adjustment is correct when the lift truck is held stationary on a slope.
- Carry out adjustments if necessary.
ADJUSTMENT OF THE PARKING BRAKE CABLE ON THE FRONT AXLE
- Press and release the brake pedal, then release the parking brake, putting it in position
B (Fig. C4/1).
- Remove the cover plate 1 (Fig. C4/2).
- Unscrew nuts 2 (Fig. C4/3).
- Adjust the cable by untightening nuts 2 (Fig. C4/3), until a clearance of 1.5 mm between cams 3 (Fig. C4/3) and stops 4 (Fig. C4/3) is obtained.
The adjustment of the stops performed by the manufacturer must not be modified under any circumstances.
ADJUSTMENT OF THE PARKING BRAKE
- Leave the parking brake in position B (Fig. C4/1).
- Progressively tighten the end piece of the lever 5 (Fig. C4/1) and recheck braking.
- Repeat the operation until the correct braking adjustment is obtained.
B
C4/1
A
5
C4/2
1
4
3
3 - 25
C4/3
3
2
2
4
INTRODUCTION TO SAFETY
C5 - F
RONT AXLE DIFFERENTIAL OIL LEVEL
CHECK
Place the lift truck on level ground with the I.C. engine stopped.
Up to machine Nr : 147615
- Remove level plug 1 (Fig. C5/1). The oil should be flush with the edge of the hole.
- If necessary, add oil (See chapter : LUBRICANTS AND FUEL in paragraph : 3 -
MAINTENANCE) by the filler port 2 (Fig. C5/1).
- Replace and tighten the level plug 1 (Fig. C5/1).
From machine Nr : 147616
- Remove level plug 1 (Fig. C5/2). The oil should be flush with the edge of the hole.
- If necessary, add oil (See chapter : LUBRICANTS AND FUEL in paragraph : 3 -
MAINTENANCE) by the same hole.
- Replace and tighten the level plug 1 (Fig. C5/2) (Tightening torque 34 to 49 N.m).
C5/1
Up to machine Nr : 147615
1
2
C5/2
From machine Nr : 147616
1
C6 - R
EAR AXLE DIFFERENTIAL OIL LEVEL
CHECK
Place the lift truck on level ground with the I.C. engine stopped.
Up to machine Nr : 147615
- Remove level plug 1 (Fig. C6/1). The oil should be flush with the edge of the hole.
- If necessary, add oil (See chapter : LUBRICANTS AND FUEL in paragraph : 3 -
MAINTENANCE) by the filler port 2 (Fig. C6/1).
- Replace and tighten the level plug 1 (Fig. C6/1).
From machine Nr : 147616
- Remove level plug 1 (Fig. C6/2). The oil should be flush with the edge of the hole.
- If necessary, add oil (See chapter : LUBRICANTS AND FUEL in paragraph : 3 -
MAINTENANCE) by the filler port 2 (Fig. C6/2).
- Replace and tighten the level plug 1 (Fig. C6/2) (Tightening torque 34 to 49 N.m).
C6/1
Up to machine Nr : 147615
1
2
C6/2
From machine Nr : 147616
2
1
3 - 26
INTRODUCTION TO SAFETY
C7 - F
RONT AND REAR WHEELS REDUCERS OIL LEVEL
CHECK
Place the lift truck on level ground with the I.C. engine stopped.
Up to machine Nr : 147615
- Check the level on each front wheel reducer.
- Place level plug 1 (Fig. C7/1) in the horizontal position.
- Remove the level plug ; the oil should be flush with the edge of the hole.
- If necessary, add oil (See chapter : LUBRICANTS AND FUEL in paragraph : 3 -
MAINTENANCE) by the same hole.
- Replace and tighten the level plug 1 (Fig. C7/1) (Tightening torque 98 to 127 N.m).
- Repeat the same operation on each rear wheel reducer.
From machine Nr : 147616
- Check the level on each front wheel reducer.
- Place level plug 1 (Fig. C7/2) in the horizontal position.
- Remove the level plug ; the oil should be flush with the edge of the hole.
- If necessary, add oil (See chapter : LUBRICANTS AND FUEL in paragraph : 3 -
MAINTENANCE) by the same hole.
- Replace and tighten the level plug 1 (Fig. C7/2) (Tightening torque 34 to 49 N.m).
- Repeat the same operation on each rear wheel reducer.
C7/1
Up to machine Nr : 147615
C7/2
From machine Nr : 147616
1
1
3 - 27
INTRODUCTION TO SAFETY
D - EVERY 500 HOURS SERVICE
Carry out the operations described previously as well as the following operations.
D1 - I.C.
ENGINE OIL
D2 - I.C.
ENGINE OIL FILTER
DRAIN
CHANGE
Place the lift truck on level ground, let the I.C. engine run at idle for a few minutes, then stop the I.C. engine.
DRAINING THE OIL
- Open the I.C. engine bonnet.
- Place a container under drain plug 1 (Fig. D1/1) and unscrew the plug 2 (Fig. D1/1).
- Take drain hose 3 (Fig. D1/2).
- Place the end of the drain hose in the container and screw fully the union on draining port 4 (Fig. D1/3).
- Remove filler cap 5 (Fig. D1/4) in order to ensure that the oil is drained properly.
Dispose of the drain oil in an ecological manner.
REPLACEMENT OF THE FILTER
- Open the battery cowl 6 (Fig. D1/5) and maintain it in open position by using the knurled nut 7 (Fig. D1/5).
- Remove I.C. engine oil filter 8 (Fig. D1/6) ; discard the filter and the filter seal.
- Clean the filter bracket with a clean, lint-free cloth.
- Fill the new oil filter (See chapter : FILTERS CARTRIDGES AND BELTS in paragraph
: 3 - MAINTENANCE) with I.C. engine oil and lightly grease the seal.
- Refit the oil filter on the filter bracket.
Tighten the oil filter by hand pressure only and lock the filter in place by a quarter turn.
FILLING UP THE OIL
- Loosen, clean and put back in place the drain hose 3 (Fig. D1/2).
- Refit and tighten drain plug 2 (Fig. D1/1).
- Fill up with oil (See chapter : LUBRICANTS AND FUEL in paragraph : 3 -
MAINTENANCE) by filler port 5 (Fig. D1/4).
- Wait a few minutes to allow the oil to flow into the sump.
- Start the I.C. engine and let it run for a few minutes.
- Check for possible leaks at the drain plug and the oil filter.
- Stop the I.C. engine, wait a few minutes and check the level between the two MAXI and MINI notches on dipstick 9 (Fig. D1/4).
- Top up the level if necessary.
1
3
D1/1
D1/2
D1/3
2
4
D1/4
5
D1/5 D1/6
7
8
9
6
3 - 28
INTRODUCTION TO SAFETY
D3 - D
RY AIR FILTER CARTRIDGE
CHANGE
In case of use in a heavily dust laden atmosphere, there are pre-filtration cartridges, see chapter : FILTERS CARTRIDGES AND BELTS in paragraph : 3 - MAINTENANCE.
Also, the checking and cleaning periodicity of the cartridge must be reduced (up to 250 hours in a heavily laden dust atmosphere and with pre-filtration).
Change the cartridge in a clean location, with the I.C. engine stopped. Never run the
I.C. engine with the air filter removed or damaged.
- Open the I.C. engine bonnet.
- Loosen the bolts and remove cover 1 (Fig. D3).
- Gently remove the cartridge 2 (Fig. D3), taking care to avoid spilling the dust.
- Leave the safety cartridge in place.
- The following parts must be cleaned with a damp, clean lint-free cloth.
• The inside of the filter and cover.
• The inside of the filter inlet hose.
• The gasket surfaces in the filter and in the cover.
- Check pipes and connections between the air filter and the I.C. engine and the connection and state of the clogging indicator on the filter.
- Before mounting check the state of the new cartridge (See chapter : FILTERS
CARTRIDGES AND BELTS in paragraph : 3 - MAINTENANCE).
- Introduce the cartridge into the filter axis and push it in, pressing the edges and not the middle.
- Reassemble the cover, guiding the valve downwards.
D4 - F
UEL FILTER CARTRIDGE
CHANGE
- Open the I.C. engine bonnet.
- Carefully clean the exterior of the filter and this bracket to prevent the dust from entering the system.
- Place a receptacle under the tank and empty using drain plug 1 (Fig. D4).
- Unscrew locking screw 2 (Fig. D4).
- Remove housing 3 (Fig. D4) and discard cartridge 4 (Fig. D4) as well as the seals of the cartridge.
- Clean the inside of the filter head and the housing, using a brush immersed in clean diesel oil.
- Refit the assembly with a new cartridge and new seals (See chapter : FILTERS
CARTRIDGES AND BELTS in paragraph : 3 - MAINTENANCE).
- If necessary, bleed the fuel circuit (See chapter : G1 - FUEL SYSTEM in paragraph : 3
- MAINTENANCE).
4
3
1
D3
D4
2
1
2
3 - 29
INTRODUCTION TO SAFETY
D5 - F
UEL LIFT PUMP
CLEAN
1st Assembly
- Open the I.C. engine bonnet.
- Unscrew retaining screw 1 (Fig. D5/1).
- Remove the strainer 2 (Fig. D5/1).
- Carefully clean the interior of fuel lift pump, strainer and cover using a brush immersed in clean diesel oil.
- Refit the assembly and make sure that the connection between the cover and the body of pump is correctly aligned with no leaks.
- Re-prime the system by activating fuel feed pump.
- If necessary, bleed the system (See chapter : G1 - FUEL SYSTEM in paragraph : 3 -
MAINTENANCE).
2nd Assembly
- Open the I.C. engine bonnet.
- Loosen connection 1 (Fig. D5/2), lift hose 2 (Fig. D5/2) and protect the aperture.
- Remove connection 3 (Fig. D5/3) and lift strainer (Fig. D5/3).
- Carefully clean the strainer and connection using a brush soaked in clean diesel fuel and dry them with a low pressure jet of compressed air.
- Reassemble connection 3 (Fig. D5/3) ensuring that the watertight seal is in the correct position (Tightening torque 20 N.m).
- Reconnect hose 2 (Fig. D5/2) and check that the feed pump is watertight.
- Re-prime the system by activating fuel feed pump.
- If necessary, bleed the system (See chapter : G1 - FUEL SYSTEM in paragraph : 3 -
MAINTENANCE).
2
1
2
D5/1
D5/2
1
D6 - T
RANSMISSION OIL FILTER
CHANGE
- Remove the cover plate 1 (Fig. D6/1).
- Unscrew and discard the transmission oil filter 2 (Fig. D6/2).
- Carefully clean the filter head with a clean, lint-free cloth.
- Slightly lubricate the new seal and fit the seal on the filter.
- Fill up the new transmission oil filter (See chapter : FILTERS CARTRIDGES AND
BELTS in paragraph : 3 - MAINTENANCE) with oil (See chapter : LUBRICANTS AND
FUEL in paragraph : 3 - MAINTENANCE).
- Refit the filter, making sure that the seal is correctly positioned and tightened.
Tighten the transmission oil filter by hand pressure only and lock the filter in place by a quarter turn.
- Put back the cover plate 1 (Fig. D6/1).
D6/1
D5/3
3
4
D6/2
2
1
3 - 30
INTRODUCTION TO SAFETY
D7 - H
YDRAULIC RETURN OIL FILTER CARTRIDGE
CHANGE
One filter for : MT 845 Série 2 + Turbo + Turbo MONO-ULTRA
MT 940 L Série 2 + Turbo + Turbo MONO-ULTRA
Two filters for : MT 1233 S Série 2 + Turbo + Turbo MONO-ULTRA
MT 1240 L Série 2 + Turbo + Turbo MONO-ULTRA
MT 1330/1740 SL Série 2 + Turbo
MT 1337/1637 SL Série 2 + Turbo + Turbo MONO-ULTRA
Thoroughly clean the outside of the filter and its surroundings before any intervention in order to prevent any risk of polluting the hydraulic circuit.
- Remove the shroud 1 (Fig. D7/1).
- Unscrew the locking screws of the cover 2 (Fig. D7/2).
- Remove the hydraulic return oil filter cartridge 3 (Fig. D7/2), and fit new replacement cartridge (See chapter : FILTERS CARTRIDGES AND BELTS in paragraph : 3 -
MAINTENANCE).
- Make sure that the cartridge is correctly positioned and refit cover 2 (Fig. D7/2).
- Put back the shroud 1 (Fig. D7/1).
1
D7/1
2
D7/2
3
D8 - B
ALANCING VALVE
CHECK
To be performed after the first 50 hours of operation and then every 500 hours.
Stop the lift truck on horizontal ground, put the handbrake on and set the reverse gear to neutral.
ROLE OF BALANCING VALVES
- The balancing valves protect the user from any risk due to a fall in hydraulic pressure or an exploding hose during hydraulic operations.
Keep everyone well away during these inspections.
In all cases, the balancing valve(s) concerned must be repaired or replaced if hydraulic movement continues after the engine has been switched off.
Never use the lift truck with a defective balancing valve.
TESTING EACH HYDRAULIC MOVEMENT
LIFTING CIRCUIT :
- Start up the lift truck and raise the jib by about 45°.
- With the engine running at mid- speed, lower the jib. While the jib is being lowered, switch off the internal combustion engine; movement should slow down as the engine speed falls and stop when the engine stops.
TELESCOPING CIRCUIT :
- Start up the lift truck and raise the jib as far as it will go, extending the telescope(s) completely.
- With the engine running at mid- speed, retract the telescope(s). When retracting the jib, switch off the internal combustion engine; movement should slow down as the engine speed falls and stop when the engine stops.
3 - 31
INTRODUCTION TO SAFETY
TILT CIRCUIT :
- Place the nominal load on the forks, anchor it correctly to prevent it from falling off during the test.
- Start up the lift truck and tilt the carriage backwards, lifting the jib sufficiently to allow the carriage to tilt.
- With the engine running at mid-speed, tilt the carriage forwards. While it is tilting, switch off the internal combustion engine; movement should slow down as the engine speed falls and stop when the engine stops.
TILT CORRECTOR CIRCUIT :
MT 940/1240 L Série 2 + Turbo + Turbo MONO-ULTRA
MT 1330/1740 SL Série 2 + Turbo
MT 1337/1637 SL Série 2 + Turbo + Turbo MONO-ULTRA
- Start up the lift truck and tilt it completely towards the right or left.
- With the engine running at mid-speed, restore it to a level position. While performing this operation, switch off the internal combustion engine; movement should slow down as the engine speed falls and stop when the engine stops.
STABILIZERS CIRCUIT :
MT 1233 S Série 2 + Turbo + Turbo MONO-ULTRA
MT 1330/1740 SL Série 2 + Turbo
MT 1337/1637 SL Série 2 + Turbo + Turbo MONO-ULTRA
- Carry out the control on the two stabilizers.
- Place the nominal load on the forks, anchor it correctly to prevent it from falling off during the test.
- Start up the lift truck and lower a stabilizer completely.
- With the engine running at mid- speed, raise the stabilizer. When raising the stabilizer, switch off the internal combustion engine; movement should slow down as the engine speed falls and stop when the engine stops.
D9 - P
ARKING BRAKE MECHANISM
GREASE
- Clean and grease articulation axles 1 (Fig. D9) with grease (See chapter :
LUBRICANTS AND FUEL in paragraph : 3 - MAINTENANCE).
D9
1
1
1
D10 - B
ATTERY ELECTROLYTE DENSITY
CHECK
D10
The electrolyte density varies depending on the temperature concerned, but a minimum of 1260 at 16°C must be maintained. In the shaded area (Fig. D10), the battery is in a normal charge condition. Readings above this zone indicate that the battery needs to be recharged.
The density should not vary more than 0.025 units between cells.
1.240
1.250
1.260
1.270
1.280
- Check the electrolyte density in each battery cell using a hydrometer.
- Do not carry out this check immediately after topping up with distilled water. Recharge
1.290
1.300
the battery for at least an hour before checking the battery electrolyte density.
°C -18 -10 0 10 20 30
Handling and servicing a battery can be dangerous, take the following precautions :
- Wear protective goggles.
- Keep the battery horizontal.
- Never smoke or work near a naked flame.
°F 0 14 32 50 68 86
- Work in a well-ventilated area.
- In the event of electrolyte being spilled onto the skin or splashing in the eyes, rinse thoroughly with cold water for 15 minutes and call a doctor.
40
104
3 - 32
INTRODUCTION TO SAFETY
D11 - F
RONT AXLE DIFFERENTIAL OIL
DRAIN
Place the lift truck on level ground with the I.C. engine stopped and the differential oil still warm.
Dispose of the drain oil in an ecological manner.
Up to machine Nr : 147615
- Place a container under drain plugs 1 (Fig. D11/1) and unscrew the plugs.
- Remove level plug 2 (Fig. D11/1) and filler plug 3 (Fig. D11/1) in order to ensure that the oil is drained properly.
- Refit and tighten drain plugs 1 (Fig. D11/1).
- Fill up with oil (See chapter : LUBRICANTS AND FUEL in paragraph : 3 -
MAINTENANCE) by filler port 3 (Fig. D11/1).
- The level is correct when the oil level is flush with the edge of port 2 (Fig. D11/1).
- Check for any possible leaks at the drain plugs.
- Refit and tighten level plug 2 (Fig. D11/1) and filler plug 3 (Fig. D11/1).
From machine Nr : 147616
- Place a container under drain plugs 1 (Fig. D11/2) and unscrew the plugs.
- Remove level plug 2 (Fig. D11/2) to ensure that the oil is drained properly.
- Refit and tighten drain plugs 1 (Fig. D11/2) (Tightening torque 34 to 49 N.m).
- Fill up with oil (See chapter : LUBRICANTS AND FUEL in paragraph : 3 -
MAINTENANCE) by level port 2 (Fig. D11/2).
- The level is correct when the oil level is flush with the edge of the hole.
- Check for any possible leaks at the drain plugs.
- Refit and tighten level plug 2 (Fig. D11/2) (Tightening torque 34 to 49 N.m).
D11/1
Up to machine Nr : 147615
2
3
1
1
1
D11/2
From machine Nr : 147616
2
D12 - R
EAR AXLE DIFFERENTIAL OIL
DRAIN
Place the lift truck on level ground with the I.C. engine stopped and the differential oil still warm.
Dispose of the drain oil in an ecological manner.
Up to machine Nr : 147615
- Place a container under drain plugs 1 (Fig. D12/1) and unscrew the plugs.
- Remove level plug 2 (Fig. D12/1) and filler plug 3 (Fig. D12/1) in order to ensure that the oil is drained properly.
- Refit and tighten drain plugs 1 (Fig. D12/1).
- Fill up with oil (See chapter : LUBRICANTS AND FUEL in paragraph : 3 -
MAINTENANCE) by filler port 3 (Fig. D12/1).
- The level is correct when the oil level is flush with the edge of port 2 (Fig. D12/1).
- Check for any possible leaks at the drain plugs.
- Refit and tighten level plug 2 (Fig. D12/1) and filler plug 3 (Fig. D12/1).
From machine Nr : 147616
- Place a container under drain plugs 1 (Fig. D12/2) and unscrew the plugs.
- Remove level plug 2 (Fig. D12/2) and filler plug 3 (Fig. D12/2) in order to ensure that the oil is drained properly.
- Refit and tighten drain plugs 1 (Fig. D12/2) (Tightening torque 34 to 49 N.m).
- Fill up with oil (See chapter : LUBRICANTS AND FUEL in paragraph : 3 -
MAINTENANCE) by filler port 3 (Fig. D12/2).
- The level is correct when the oil level is flush with the edge of port 2 (Fig. D12/2).
- Check for any possible leaks at the drain plugs.
- Refit and tighten level plug 2 (Fig. D12/2) (Tightening torque 34 to 49 N.m) and filler plug 3 (Fig. D12/2) (Tightening torque 34 to 49 N.m).
3 - 33
1
1
D12/1
Up to machine Nr : 147615
1
2
3
1
1
1
D12/2
From machine Nr : 147616
3
2
1
1
1
INTRODUCTION TO SAFETY
D13 - B
LANKING CAP ON THE INDUCTION MANIFOLD
CHECK
MT 845 Série 2
MT 940/1240 L Série 2
MT 1233 S Série 2
MT 1330/1337/1637 SL Série 2
(Only for I.C. Engine AR 81026 up to serial Nr U 170804 H)
If the cap on the induction manifold 1 (Fig. D13) have craks or heat damage, renew the cap immediately.
Failure to change a cracked or damaged rubber cap may cause the entry of air that is not filtered, this can result in severe damage to the I. C. engine. If any other type of cap is found to be fitted, it is to removed and the correct cap fitted immediately.
D13
1
3 - 34
INTRODUCTION TO SAFETY
3 - 35
INTRODUCTION TO SAFETY
E - EVERY 1000 HOURS SERVICE
Carry out the operations described previously as well as the following operations.
E1 - F
UEL TANK
CLEAN
While carrying out these operations, do not smoke or work near a flame.
Place the lift truck on level ground with the I.C. engine stopped.
- Inspect the parts susceptible to leaks in the fuel circuit and in the tank.
- In the event of a leak, contact your dealer.
Never try to carry out a weld or any other operation by yourself, this could provoke an explosion or a fire.
- Place a container under drain plug 1 (Fig. E1/1) and unscrew the plug.
- Open the access panel for fuel filling.
- Remove cap 2 (Fig. 1/2) and set it on its bracket.
- Let the fuel flow and clean with 10 litres of clean fuel by filler port 3 (Fig. E1/2).
- Refit and tighten drain plug 1 (Fig. E1/1) (Tightening torque 29 to 39 N.m).
- Fill the fuel tank with clean fuel (See chapter : LUBRICANTS AND FUEL in paragraph :
3 - MAINTENANCE) filtered through a strainer or a clean, lint-free cloth and refit the filler plug 2 (Fig. E1/2).
- Close the access panel for fuel filling and open the I.C. engine bonnet.
- Re-prime the system by activating fuel feed pump 4 (Fig. E1/3).
- If necessary, bleed the system (See chapter : G1 - FUEL SYSTEM in paragraph : 3 -
MAINTENANCE).
2
E1/1
1
E1/2
3
E2 - S
AFETY DRY AIR FILTER CARTRIDGE
CHANGE
- For the disassembly and reassembly of the cartridge, see chapter : D3 - DRY AIR
FILTER CARTRIDGE in paragraph : 3 - MAINTENANCE.
- Gently remove the dry air filter safety cartridge 1 (Fig. E2), taking care to avoid spilling the dust.
- Clean the gasket surface on the filter with a damp, clean lint-free cloth.
- Before mounting check the state of the new safety cartridge (See chapter : FILTERS
CARTRIDGES AND BELTS in paragraph : 3 - MAINTENANCE).
- Introduce the cartridge into the filter axis and push it in, pressing the edges and not the middle.
NOTE : The periodicity for changing the safety cartridge is given for information only.
The safety cartridge must be changed for every two changes of the air filter cartridge.
3 - 36
1
E2
E1/3
4
INTRODUCTION TO SAFETY
E3 - T
RANSMISSION OIL
E4 - T
RANSMISSION HOUSING STRAINER
DRAIN
CLEAN
Place the lift truck on level ground with the I.C. engine stopped, the transmission oil still warm.
Up to machine Nr : 147615
DRAINING THE OIL
- Place a container under drain plugs 1 (Fig. E3/1) and under cover 2 (Fig. E3/1) and unscrew the drain plugs.
- Remove cover plate 3 (Fig. E3/2).
- Remove dipstick 4 (Fig. E3/3) and unscrew filling plug 5 (Fig. E3/3) in order to ensure that the oil is drained properly.
Dispose of the drain oil in an ecological manner.
CLEANING THE STRAINER
- Remove cover 2 (Fig. E3/1) and set aside the O-ring joint and sealing washer.
- Allow the rest of the oil to drain away.
- Remove and clean the strainer using a compressed air jet.
- Clean the magnetic section on the plate.
- Refit the assembly and tighten up plate 2 (Fig. E3/1) (Tightening torque 18 to 31 N.m).
FILLING UP THE OIL
- Refit and tighten drain plugs 1 (Fig. E3/1) (Tightening torque 34 to 54 N.m).
- Fill up with oil (See chapter : LUBRICANTS AND FUEL in paragraph : 3 -
MAINTENANCE) by filler port 6 (Fig. E3/3) and refit the plug.
- Check the level with the dipstick 4 (Fig. E3/3) (See chapter : A5 - TRANSMISSION OIL
LEVEL in paragraph : 3 - MAINTENANCE).
- Check any possible leaks from the drain plugs or cover.
- Put back the cover plate 3 (Fig. E3/2).
1
4
E3/1
E3/2
3
E3/3
1
2
5
6
From machine Nr : 147616
DRAINING THE OIL
- Place a container under drain plug 1 (Fig. E3/4) and under cover 2 (Fig. E3/5) and unscrew the drain plug.
- Remove cover plate 3 (Fig. E3/6).
- Remove dipstick 4 (Fig. E3/7) and unscrew filling plug 5 (Fig. E3/7) in order to ensure that the oil is drained properly.
Dispose of the drain oil in an ecological manner.
3 - 37
E3/4
1
INTRODUCTION TO SAFETY
CLEANING THE STRAINER
- Remove cover 2 (Fig. E3/5) and set aside the O-ring joint and sealing washer.
- Allow the rest of the oil to drain away.
- Remove and clean the strainer using a compressed air jet.
- Clean the magnetic section on the plate.
- Refit the assembly and tighten up plate 2 (Fig. E3/5) (Tightening torque 18 to 31 N.m).
Filling up the oil
- Refit and tighten drain plug 1 (Fig. E3/4) (Tightening torque 34 to 54 N.m).
- Fill up with oil (See chapter : LUBRICANTS AND FUEL in paragraph : 3 -
MAINTENANCE) by filler port 5 (Fig. E3/7) and refit the plug.
- Check the level with the dipstick 4 (Fig. E3/7) (See chapter : A5 - TRANSMISSION OIL
LEVEL in paragraph : 3 - MAINTENANCE).
- Check any possible leaks from the drain plug or cover.
- Put back the cover plate 3 (Fig. E3/6).
E3/5
E3/6
3
E5 - A
NGLE GEAR BOX OIL
DRAIN
Place the lift truck on level ground with the I.C. engine stopped, the angle gear box oil still warm.
- Place a container under drain plug 1 (Fig. E5/1) and unscrew the plug.
- Remove cover plate 2 (Fig. E5/2).
- Remove dipstick 3 (Fig. E5/3) and unscrew filler cap 4 (Fig. E5/3) in order to ensure that the oil is drained properly.
Dispose of the drain oil in an ecological manner.
- Refit and tighten drain plug 1 (Fig. E5/1) (Tightening torque 20 to 29 N.m).
- Fill up with oil (See chapter : LUBRICANTS AND FUEL in paragraph : 3 -
MAINTENANCE) by filler port 4 (Fig. E5/3) and refit the filler cap (Tightening torque 20 to 29 N.m).
- Check the correct level between the MINI and MAXI marks on dipstick 3 (Fig. E5/3).
- Check any possible leaks from the drain plug.
- Put back the cover plate 2 (Fig. E5/2).
E5/1 E5/2
2
1
3 - 38
5
E3/7
4
3
E5/3
4
2
INTRODUCTION TO SAFETY
E6 - H
YDRAULIC OIL
E7 - S
UCTION STRAINER FOR HYDRAULIC OIL TANK
E8 - F
ILTER CAP FOR HYDRAULIC OIL TANK
DRAIN
CLEAN
CHANGE
Place the lift truck on level ground with the I.C. engine stopped and telescope jib retracted and lowered as far as possible.
Before any intervention, thoroughly clean the area surrounding the drain plug and the suction cover on the hydraulic tank.
DRAINING THE OIL
- Place a container under drain plug 1 (Fig. E6/1) and unscrew the plug.
- Open the access panel for hydraulic oil filling.
- Remove filler cap 2 (Fig. E6/2) in order to ensure that the oil is drained properly.
Dispose the drain oil in an ecological manner.
CLEANING THE STRAINER
- Remove the shroud 3 (Fig. E6/3).
- Remove suction cover 4 (Fig. E6/4).
- Remove and clean the strainer using a compressed air jet, check its condition and replace if necessary (See chapter : FILTERS CARTRIDGES AND BELTS in paragraph
: 3 - MAINTENANCE).
- Refit the strainer and tighten the suction cover 4 (Fig. E6/4) making sure the seal is in the correct position.
FILLING UP THE OIL
- Clean and refit drain plug 1 (Fig. E6/1) (Tightening torque 29 to 39 N.m).
- Fill up with oil (See chapter : LUBRICANTS AND FUEL in paragraph : 3 -
MAINTENANCE) by filler port 5 (Fig. E6/2).
Use a clean container and funnel and clean the underside of the oil drum before filling.
- Observe the oil level on dipstick 6 (Fig. E6/5) ; the oil level should be at the level of the red point.
- Check for any possible leaks at the drain plug.
- Replace filler plug 2 (Fig. E6/2) with a new filler plug (See chapter : FILTERS
CARTRIDGES AND BELTS in paragraph : 3 - MAINTENANCE).
POLLUTION ABATEMENT OF THE HYDRAULIC CIRCUIT
- Let the I.C. engine run (Accelerator pedal at halfway travel) for 5 minutes without using anything on the lift truck, then for 5 more minutes while using completely the hydraulic movements (Except the steering system and the service brakes).
- Accelerate the I.C. engine at full speed for 1 minute, then activate the steering system and the service brakes.
E6/4
- This operation makes a pollution abatement of the circuit possible through the hydraulic return oil filter.
4
2
3
6
E6/1
1
E6/2
E6/3
E6/5
5
3 - 39
INTRODUCTION TO SAFETY
E9 - S
EAT BELT
CHECK
SEAT BELT WITH TWO ANCHORING POINTS
- Check the following points :
• Fixing of the anchoring points on the seat.
• Cleanness of the strap and the locking mechanism.
• Triggering of the locking mechanism.
• Condition of the strap (cuts, curled edges).
REELED SEAT BELT WITH TWO ANCHORING POINTS
- Check the points listed above together with the following points :
• The correct winding of the belt.
• Condition of the reel guards.
• Roller locking mechanism when the strap is given a sharp tug.
NOTE : After an accident, replace the seat belt.
Under no circumstances should you use the lift truck if the seat belt is faulty (fixing, locking, it has cuts or tears, etc). Repair or replace the seat belt immediately.
E10 - N/A
L
OAD STATUS INDICATOR DEVICE
GREASE
Up to machine Nr : 147615
- Clean lubricator 1 (Fig. E10).
- Lubricate with grease (See chapter : LUBRICANTS AND FUEL in paragraph : 3 -
MAINTENANCE).
- Remove the surplus of grease.
E10
1
E11 - F
RONT AND REAR WHEELS REDUCERS OIL
DRAIN
Place the lift truck on level ground with the I.C. engine stopped and the reducers oil still warm.
Dispose the drain oil in an ecological manner.
Up to machine Nr : 147615
- Drain and change each front wheel reducer.
- Place drain plug 1 (Fig. E11/1) in position A.
- Place a container under the drain plug and unscrew the plug.
- Let the oil drain fully.
- Place the drain port in position B, i.e. in a level port.
- Fill up with oil (See chapter : LUBRICANTS AND FUEL in paragraph : 3 -
MAINTENANCE) by level port 1 (Fig. E11/1).
- The level is correct when the oil level is flush with the edge of the hole.
- Refit and tighten the drain plug 1 (Fig. E11/1) (Tightening torque 98 to 127 N.m).
- Repeat this operation on each rear wheel reducer.
3 - 40
E11/1
Up to machine Nr : 147615
A
1
B
INTRODUCTION TO SAFETY
From machine Nr : 147616
- Drain and change each front wheel reducer.
- Place drain plug 1 (Fig. E11/2) in position A.
- Place a container under the drain plug and unscrew the plug.
- Let the oil drain fully.
- Place the drain port in position B, i.e. in a level port.
- Fill up with oil (See chapter : LUBRICANTS AND FUEL in paragraph : 3 -
MAINTENANCE) by level port 1 (Fig. E11/2).
- The level is correct when the oil level is flush with the edge of the hole.
- Refit and tighten the drain plug 1 (Fig. E11/2) (Tightening torque 34 to 49 N.m).
- Repeat this operation on each rear wheel reducer.
E11/2
From machine Nr : 147616
1
B
A
3 - 41
INTRODUCTION TO SAFETY
F - EVERY 2000 HOURS SERVICE
Carry out the operations described previously as well as the following operations.
F1 - C
OOLING LIQUID
DRAIN
These operations are to be carried out if necessary or every two years at the beginning of winter. Place the lift truck on level ground with the I.C. engine stopped and cold.
DRAINING THE LIQUID
- Open the I.C. engine bonnet.
- Remove the shroud 1 (Fig. F1/1).
- Place a container under drain plug 2 (Fig. F1/2) of the radiator and drain plug 3 (Fig.
F1/3) of the I.C. engine block and unscrew the plugs.
- Remove filler cap 4 (Fig. F1/4) of the radiator.
- Let the cooling circuit drain entirely while ensuring that the ports do not get clogged.
- Check the condition of the hoses as well as the fastening devices and change the hoses if necessary.
- Rinse the circuit with clean water and use a cleaning agent if necessary.
MT 845 Turbo Série 2 + T M-U
MT 940/1240 L Turbo Série 2 + T M-U
MT 1233 S Turbo Série 2 + T M-U
MT 1330/1740 SL Turbo Série 2
MT 1337/1637 SL Turbo Série 2 + T M-U
- Disconnect hoses 5 and 6 (Fig. F1/5) of the oil cooler and rinse via outlet hole 5 (Fig.
F1/5) until clean water flows from input hole 6 (Fig. F1/5).
- Reconnect the two hoses.
FILLING THE LIQUID
- Retighten drain plug 2 (Fig. F1/2) (Tightening torque 20 N.m) and 3 (Fig. F1/3)
(Tightening torque 7 to 12 N.m).
- Slowly fill up the cooling circuit (See chapter : LUBRICANTS AND FUEL in paragraph :
3 - MAINTENANCE) to 12 mm under filler port 7 (Fig. F1/4).
- Put back filler cap 4 (Fig. F1/4).
- Run the I.C. engine at idle for a few minutes.
- Check for any possible leaks.
- Put back the shroud 1 (Fig. F1/1)
- Check the level and refill if necessary.
The I.C. engine does not contain any corrosion resistor and must be filled during the whole year with a mixture containing 25 % of ethylene glycol-based antifreeze.
1
F1/1
F1/2
F1/3
2
3
F1/4
4
7
3 - 42
F1/5
6
5
INTRODUCTION TO SAFETY
3 - 43
INTRODUCTION TO SAFETY
G - OCCASIONAL MAINTENANCE
G1 - F
UEL SYSTEM
BLEED
These operations are to be carried out only in the following cases :
- A component of the fuel system replaced or drained.
- A drained tank.
- Running out of fuel.
Ensure that the level of fuel in the tank is sufficient, turn the ignition key to notch 1 to establish electrical contact and bleed in the following order :
- Open the I.C. engine bonnet.
BLEEDING THE FUEL FILTER
- Loosen bleed screw 1 (Fig. G1/1).
- Activate feed pump 2 (Fig. G1/2) until the diesel fuel flows out free from air at the bleed screw.
NOTE : If the lever on the feed pump is in the maximum raised position, turn the crankshaft by one turn.
- Tighten the bleed screw while the diesel fuel is flowing out.
G1/1
1
G1/2
2
BLEEDING THE HEATER PLUG
- Loosen connection 3 (Fig. G1/3) on the heater plug.
- Activate feed pump 2 (Fig. G1/2) until the diesel fuel is flowing out free from air at the connection.
- Tighten the connection while the diesel fuel is flowing out.
Immobilise the heater plug with a spanner before loosening connection 3 (Fig. G1/3).
3
G1/3
BLEEDING THE INJECTION PUMP
- Loosen connection 4 (Fig. G1/4) of the low pressure fuel return circuit on the regulator housing.
- Activate feed pump 2 (Fig. G1/2) until the diesel fuel is flowing out free from air at the connection.
- Tighten the connection while the diesel fuel is flowing out.
G1/4
4
3 - 44
INTRODUCTION TO SAFETY
BLEEDING THE INJECTORS
- Loosen high pressure connectors 5 (Fig. G1/5) of two of the injectors.
- Activate the starter until the diesel fuel flows out free of air at connections 5 (Fig. G1/5).
- Tighten the connection while the diesel fuel is flowing out (Tightening torque 22 N.m).
The I.C. engine is then ready to be started up.
Turn the I.C. engine over slowly for 5 minutes immediately after bleeding the fuel feed circuit, in order to ensure that the injection pump has been bled thoroughly.
NOTE : If the I.C. engine functions correctly for a short time then stops or functions irregularly, check for possible leaks in the low pressure circuit. If in doubt,
contact your dealer.
G1/5
5
5
5 5
G2 - W
HEEL
CHANGE
In the event of a wheel being changed on the public highway, make sure of the following points :
- Stop the lift truck, if possible on even and hard ground.
- To pass on stop of lift truck (See chapter : DRIVING INSTRUCTIONS in paragraph : 1
- OPERATING AND SAFETY INSTRUCTIONS).
- Put the warning lights on.
- Immobilise the lift truck in both directions on the axle opposite to the wheel to be changed.
- Unlock the nuts of the wheel to be changed.
- Place the jack under the flared axle tube, as near as possible to the wheel and adjust the jack (Fig. G2/1).
- Lift the wheel until it comes off the ground and put in place the safety support under the axle (Fig. G2/2).
For this operation, we advise you to use the hydraulic jack MANITOU Reference 505
507 and the safety support MANITOU Reference 554 772.
- Completely unscrew the wheel nuts and remove them.
- Free the wheel by reciprocating movements and roll it to the side.
- Slip the new wheel on the wheel hub.
- Refit the nuts by hand, if necessary grease them.
- Remove the safety support and lower the lift truck with the jack.
- Tighten the wheel nuts with a torque wrench (See chapter : A - DAILY OR EVERY 10
HOURS SERVICE in paragraph : 3 - MAINTENANCE for tightening torque).
G2/1
G2/2
3 - 45
INTRODUCTION TO SAFETY
G3 - L
IFT TRUCK
TOW
Do not tow the lift truck at more than 25 km/h.
- Put the forward/reverse lever and the gear shift in neutral.
- Release the parking brake.
- Put the warning lights on.
- If the I.C. engine is not running there will be no steering or braking assistance. Operate the steering and pedal slowly avoiding sudden jerky movements.
G4 - L
IFT TRUCK
SLING
- Take into account the position of the lift truck gravity center for lifting (Fig. G4/1).
- Place the hooks in the fastening points provided (Fig. G4/2 and G4/3).
G4/1
B A
MT 845 Série 2 + T + T M-U
A = 1695 mm B = 1075 mm
MT 940 L Série 2 + T + T M-U
A = 1630 mm B = 1140 mm
MT 1233 S Série 2 + T + T M-U
A = 1375 mm B = 1395 mm
MT 1240 L Série 2 + T + T M-U
A = 1460 mm B = 1310 mm
MT 1330 SL Série 2 + T
A = 1300 mm B = 1470 mm
MT 1337 SL Série 2 + T + T M-U
A = 1560 mm B = 1210 mm
MT 1637 SL Série 2 + T + T M-U
A = 1580 mm B = 1190 mm
MT 1740 SL Série 2 + T
A = mm B = mm
G4/2 G4/3
MT 845 Série 2 + T + T M-U
MT 940/1240 L Série 2 + T + T M-U
MT 1337/1637 SL Série 2 + T + T M-U
MT 1740 SL Série 2 + T
G4/3
MT 1233 S Série 2 + T + T M-U
MT 1330 SL Série 2 + T
3 - 46
INTRODUCTION TO SAFETY
G5 - L
IFT TRUCK ON A PLATFORM
TRANSPORT
Ensure that the safety instructions connected to the platform are respected before the loading of the lift truck and that the driver of the means of transport is informed about the dimensions and the weight of the lift truck (See chapter :
CHARACTERISTICS in paragraph : 2 - DESCRIPTION).
Ensure that the platform has got dimensions and a load capacity sufficient for transporting the lift truck. Check also the pressure on the contact surface allowable for the platform in connection with the lift truck.
For lift trucks equipped with a turbo-charged I.C. engine, block off the exhaust outlet to avoid rotation of the turbo shaft without lubrication when transporting the vehicle.
LOAD THE LIFT TRUCK
- Block the wheels of the platform.
- Fix the loading ramps so that you obtain an angle as little as possible to lift the lift truck.
- Load the lift truck parallel to the platform.
- Stop the lift truck (See chapter : DRIVING INSTRUCTIONS in paragraph : 1 -
OPERATING AND SAFETY INSTRUCTIONS).
STOW THE LIFT TRUCK
- Fix the chocks to the platform at the front and at the back of each tyre (Fig. G5/1).
- Fix also the chocks to the platform in the inside of each tyre (Fig. G5/2).
- Stow the lift truck on the platform with enough resisting ropes. At the front of the lift truck, on the fastening points 1 (Fig. G5/3) and at the back, on the towing pin 2 (Fig.
G5/4).
- Tighten the ropes (Fig. G5/5).
G5/1
G5/2
1
G5/3
1
G5/4
MT 845 Série 2 + T + T M-U
MT 940/1240 L Série 2 + T + T M-U
MT 1337/1637 SL Série 2 + T + T M-U
MT 1740 SL Série 2 + T
G5/4
MT 1233 S Série 2 + T + T M-U
MT 1330 SL Série 2 + T
G5/5
2
3 - 47
2
INTRODUCTION TO SAFETY
G6 - F
RONT HEADLAMPS
RECOMMENDED SETTING
(As per standard ECE-76/756 76/761 ECE20)
Set to - 2% of the dipped beam in relation to the horizontal line of the headlamp.
ADJUSTING PROCEDURE
- Place the lift truck unloaded and in the transport position and perpendicular to a white wall on flat, level ground (Fig.
G6).
- Check the tyre pressures (See chapter : A6 - TYRES
PRESSURE AND WHEEL NUTS TORQUE in paragraph :
3 - MAINTENANCE).
- Put the gear reverser lever in neutral and release the parking brake.
h2 = h1 - (l x 2 / 100)
+%
-% h1 h2 h1
-2%
G6 l
CALCULATING THE HEIGHT OF THE DIPPED BEAM (h2)
• h1 = Height of the dipped beam in relation to the ground.
• h2 = Height of the adjusted beam.
• l = Distance between the dipped beam and the white wall.
ADJUST
3 - 48
INTRODUCTION TO SAFETY
4 - ADAPT ABLE
A TT ACHMENTS
4 - 1
INTRODUCTION TO SAFETY
4 - 2
INTRODUCTION TO SAFETY
INTRODUCTION
- A wide range of attachments studied and perfectly adapted to your lift truck is available and guaranteed by the manufacturer.
- The attachments are delivered with a load chart concerning your lift truck. The operator's manual and the load chart should be kept in the places provided in the lift truck. For standard attachments, their use is governed by the instructions contained on this notice.
We would remind users that the MT 1637 SL Série 2 + Turbo + Turbo MONO-ULTRA et MT 1740 SL Série 2 + Turbo, are lift trucks essentially intended for handling. Occasional use with the buckets CBC 800 and CBR 900 is authorised, but under no circumstances is intensive use for difficult applications (quarry, waste, cereals, agriculture, etc) permissible.
In addition, use of the lift truck with the buckets CBC 800 and CBR 900 should be with the jib completely retracted, in order to reduce the constraints on the jib head.
Use other buckets CBA, CBC, CBR, CB, CBG and manure forks FF, FFGR is forbidden.
- Some particular uses require the adaptation of the attachment which is not provided in the price-listed options. Optional solutions exist, consult your dealer.
It is COMPULSORY for all ATTACHMENTS WITH SUSPENDED LOAD (Hoist, crane jib, crane jib with winch, hook, etc.) to be used with a fork lift fitted with AUTOMATIC HYDRAULIC MOVEMENT CUT-OFF.
Only attachments approved by the manufacturer are to be used on our lift trucks (See chapter : TECHNICAL SPECIFICATIONS
OF ATTACHMENTS in paragraph : 4 - ADAPTABLE ATTACHMENTS IN OPTION ON THE RANGE). The manufacturer's liability will be denied in case of modification or of attachment adaptation carried out without his knowing it.
The single side-shift carriage (TSDL) is only compatible with the following attachments:
• floating fork carriage (TFF)
• tilting fork carriage (PFB)
• loading bucket (CBR)
• concrete bucket (BB, BBG)
• spout bucket (GL)
• crane jib and crane jib with winch (P, PT, PO, PC)
• winch (H)
• fixed platform, swivelling platform, roofer’s platform.
It is prohibited to use any other attachments on the TSDL.
Attachments authorised for use on the TSDL must comply strictly with the applications for which they are designed.
It is prohibited to use them for any other application (for example, earth moving, excavation, desurfacing, back scraping, etc.
for the loading bucket CBR) or any application placing abnormal stress on the structure of the TSDL : risk of deformation which could cause the load to fall.
Depending on their size, certain attachments may, when the jib is lowered and retracted, come into contact with the front tyres and cause damage to them, if reverse tilt is activated in the forward tilt direction. TO REMOVE THIS RISK, EXTEND THE
TELESCOPE TO A SUFFICIENT EXTENT FOR THE PARTICULAR LIFT TRUCK AND ATTACHMENT SO THAT THIS CONTACT
IS NOT POSSIBLE.
Maximum loads are defined by the capacity of a lift truck taking account of the attachment’s weight and centre of gravity. In the event of the attachment having less capacity than the lift truck, never exceed this limit.
4 - 3
INTRODUCTION TO SAFETY
PICKING UP THE ATTACHMENTS
A - A
TTACHMENT WITHOUT HYDRAULICS AND HAND LOCKING DEVICE
B - A
TTACHMENT WITHOUT HYDRAULICS AND HYDRAULIC LOCKING DEVICE
(O
PTION
)
MT 845 Série 2 + Turbo
MT 940/1240 L Série 2 + Turbo
MT 1233 S Série 2 + Turbo
MT 1330/1740 SL Série 2 + Turbo
MT 1337/1637 SL Série 2 + Turbo
C - A
TTACHMENT WITHOUT HYDRAULICS AND HYDRAULIC LOCKING DEVICE
(O
PTION
)
MT 845 Turbo MONO-ULTRA Série 2
MT 940/1240 L Turbo MONO-ULTRA Série 2
MT 1233 S Turbo MONO-ULTRA Série 2
MT 1337/1637 SL Turbo MONO-ULTRA Série 2
D - H
YDRAULIC ATTACHMENT AND HAND LOCKING DEVICE
MT 845 Série 2 + Turbo
MT 940/1240 L Série 2 + Turbo
MT 1233 S Série 2 + Turbo
MT 1330/1740 SL Série 2 + Turbo
MT 1337/1637 SL Série 2 + Turbo
E - H
YDRAULIC ATTACHMENT AND HAND LOCKING DEVICE
MT 845 Turbo MONO-ULTRA Série 2
MT 940/1240 L Turbo MONO-ULTRA Série 2
MT 1233 S Turbo MONO-ULTRA Série 2
MT 1337/1637 SL Turbo MONO-ULTRA Série 2
F - H
YDRAULIC ATTACHMENT AND HYDRAULIC LOCKING DEVICE
(O
PTION
)
MT 845 Série 2 + Turbo
MT 940/1240 L Série 2 + Turbo
MT 1233 S Série 2 + Turbo
MT 1330/1740 SL Série 2 + Turbo
MT 1337/1637 SL Série 2 + Turbo
G - H
YDRAULIC ATTACHMENT AND HYDRAULIC LOCKING DEVICE
(O
PTION
)
MT 845 Turbo MONO-ULTRA Série 2
MT 940/1240 L Turbo MONO-ULTRA Série 2
MT 1233 S Turbo MONO-ULTRA Série 2
MT 1337/1637 SL Turbo MONO-ULTRA Série 2
4 - 4
INTRODUCTION TO SAFETY
4 - 5
INTRODUCTION TO SAFETY
A - A
TTACHMENT WITHOUT HYDRAULICS AND HAND LOCKING DEVICE
TAKING UP AN ATTACHMENT
- Ensure that the attachment is in a position facilitating the locking to the carriage. If it is not correctly oriented, take the necessary precautions in order to move it safely.
- Check that the locking pin and the clip are in position in the bracket (Fig. A).
- Place the lift truck with the jib lowered in front of and parallel to the attachment, tilt the carriage forwards (Fig. B).
- Bring the carriage under the locking tube of the attachment, slightly lift the jib, incline the carriage backwards in order to position the attachment (Fig. C).
- Lift the attachment off the ground to facilitate locking.
HAND LOCKING
- Take the locking pin and the clip on the bracket (Fig. A) and lock the attachment (Fig.
D). Do not forget to refit the clip.
HAND RELEASING
- Proceed in the reverse order of paragraph HAND LOCKING while making sure you put back the locking pin and the clip in the bracket (Fig. A).
LAYING AN ATTACHMENT
- Proceed in the reverse order of paragraph TAKING UP AN ATTACHMENT while making sure you place the attachment flat on the ground and in closed position.
A
B
C
D
4 - 6
INTRODUCTION TO SAFETY
B - A
TTACHMENT WITHOUT HYDRAULICS AND HYDRAULIC LOCKING
DEVICE
(O
PTION
)
MT 845 Série 2 + Turbo
MT 940/1240 L Série 2 + Turbo
MT 1233 S Série 2 + Turbo
MT 1330/1740 SL Série 2 + Turbo
MT 1337/1637 SL Série 2 + Turbo
TAKING UP AN ATTACHMENT
- Ensure that the attachment is in a position facilitating the locking to the carriage. If it is not correctly oriented, take the necessary precautions in order to move it safely.
- Check that the rods on the locking cylinder are retracted (Fig. A).
- Place the lift truck with the jib lowered in front of and parallel to the attachment, tilt the carriage forwards (Fig. B).
- Bring the carriage under the locking tube of the attachment, slightly lift the jib, incline the carriage backwards in order to position the attachment (Fig. C).
- Lift the attachment off the ground to facilitate locking.
HYDRAULIC LOCKING (OPTION)
- Put the valve in position A (Fig. D), that is to say, the hydraulic circuit of the attachment locking open.
- Push the lever of the distributor 1 (Fig. E) forwards in order to completely lock the attachment on the carriage.
- Close the valve in position B (Fig. D), that is to say, the hydraulic circuit of the attachment locking closed.
Always close the valve in position B (Fig. D) after the locking of the attachment, in order to avoid accidental unlocking and use the attachment safely.
HYDRAULIC RELEASING (OPTION)
- Put the valve in position A (Fig. D), that is to say, the hydraulic circuit of the attachment locking open.
- Pull the lever of the distributor 1 (Fig. E) backwards in order to unlock the attachment on the carriage.
LAYING AN ATTACHMENT
- Proceed in the reverse order of paragraph TAKING UP AN ATTACHMENT while making sure you place the attachment flat on the ground and in closed position.
A
B
C
E
1
D
A
B
4 - 7
INTRODUCTION TO SAFETY
C - A
TTACHMENT WITHOUT HYDRAULICS AND HYDRAULIC LOCKING
DEVICE
(O
PTION
)
MT 845 Turbo MONO-ULTRA Série 2
MT 940/1240 L Turbo MONO-ULTRA Série 2
MT 1233 S Turbo MONO-ULTRA Série 2
MT 1337/1637 SL Turbo MONO-ULTRA Série 2
TAKING UP AN ATTACHMENT
- Ensure that the attachment is in a position facilitating the locking to the carriage. If it is not correctly oriented, take the necessary precautions in order to move it safely.
- Check that the rods on the locking cylinder are retracted (Fig. A).
- Place the lift truck with the jib lowered in front of and parallel to the attachment, tilt the carriage forwards (Fig. B).
- Bring the carriage under the locking tube of the attachment, slightly lift the jib, incline the carriage backwards in order to position the attachment (Fig. C).
- Lift the attachment off the ground to facilitate locking.
HYDRAULIC LOCKING
- Put the valve in position A (Fig. D), that is to say, the hydraulic circuit of the attachment locking open.
- Press the button 1 (Fig. E) of the distributor lever and push the lever to the right so as to completely lock the attachment onto the carriage.
- Close the valve in position B (Fig. D), that is to say, the hydraulic circuit of the attachment locking closed.
Always close the valve in position B (Fig. D) after the locking of the attachment, in order to avoid accidental unlocking and use the attachment safely.
HYDRAULIC RELEASING
- Put the valve in position A (Fig. D), that is to say, the hydraulic circuit of the attachment locking open.
- Press the button 1 (Fig. E) of the distributor lever and push the lever to the left so as to completely unlock the attachment.
LAYING AN ATTACHMENT
- Proceed in the reverse order of paragraph TAKING UP AN ATTACHMENT while making sure you place the attachment flat on the ground and in closed position.
INACTIVATE THE HYDRAULIC RELEASE CONTROL
You can change an attachment without leaving the control post, by cutting the electricity supply to the hydraulic control.
- Leave the valve in position A (Fig. D).
- Use switch 2 (Fig. F) to cut the electricity supply to the hydraulic control. The circuit is out of action when indicator 3 (Fig. F) is on.
Always cut the electrical power to the circuit using switch 2 (Fig. F) after each change of attachment to avoid involuntary release and use the attachment in complete safety.
A
B
C
D
A
B
4 - 8
INTRODUCTION TO SAFETY
E
MT 845 Turbo MONO-ULTRA Série 2
MT 1233 S Turbo MONO-ULTRA Série 2
1st ASSEMBLY 2nd ASSEMBLY
1
1
E
MT 940/1240 L Turbo MONO-ULTRA Série 2
MT 1337 SL Turbo MONO-ULTRA Série 2
MT 1637 SL Turbo MONO-ULTRA Série 2
1st ASSEMBLY 2nd ASSEMBLY
1
1
F
2
3
4 - 9
INTRODUCTION TO SAFETY
D - H
YDRAULIC ATTACHMENT AND HAND LOCKING DEVICE
MT 845 Série 2 + Turbo
MT 940/1240 L Série 2 + Turbo
MT 1233 S Série 2 + Turbo
MT 1330/1740 SL Série 2 + Turbo
MT 1337/1637 SL Série 2 + Turbo
TAKING UP AN ATTACHMENT
- Ensure that the attachment is in a position facilitating the locking to the carriage. If it is not correctly oriented, take the necessary precautions in order to move it safely.
- Check that the locking pin and the clip are in position in the bracket (Fig. A).
- Place the lift truck with the jib lowered in front of and parallel to the attachment, tilt the carriage forwards (Fig. B).
- Bring the carriage under the locking tube of the attachment, slightly lift the jib, incline the carriage backwards in order to position the attachment (Fig. C).
- Lift the attachment off the ground to facilitate locking.
HAND LOCKING AND CONNECTING THE ATTACHMENT
- Take the locking pin and the clip on the bracket (Fig. A) and lock the attachment (Fig.
D). Do not forget to refit the clip.
- Stop the engine.
- Remove the pressure of the hydraulic circuit by using the lever of the distributor 1 (Fig.
E).
- Connect the rapid connectors according to the logic of the attachment’s hydraulic movements.
Make sure that the rapid connectors are clean and protect the holes which are not used, with the caps provided.
HAND RELEASING AND DISCONNECTING THE ATTACHMENT
- Proceed in the reverse order of paragraph HAND LOCKING AND CONNECTING THE
ATTACHMENT while making sure you put back the locking pin and the clip in the bracket (Fig. A).
LAYING AN ATTACHMENT
- Proceed in the reverse order of paragraph TAKING UP AN ATTACHMENT while making sure you place the attachment flat on the ground and in closed position.
A
B
C
D E
1
4 - 10
INTRODUCTION TO SAFETY
E - H
YDRAULIC ATTACHMENT AND HAND LOCKING DEVICE
MT 845 Turbo MONO-ULTRA Série 2
MT 940/1240 L Turbo MONO-ULTRA Série 2
MT 1233 S Turbo MONO-ULTRA Série 2
MT 1337/1637 SL Turbo MONO-ULTRA Série 2
TAKING UP AN ATTACHMENT
- Ensure that the attachment is in a position facilitating the locking to the carriage. If it is not correctly oriented, take the necessary precautions in order to move it safely.
- Check that the locking pin and the clip are in position in the bracket (Fig. A).
- Place the lift truck with the jib lowered in front of and parallel to the attachment, tilt the carriage forwards (Fig. B).
- Bring the carriage under the locking tube of the attachment, slightly lift the jib, incline the carriage backwards in order to position the attachment (Fig. C).
- Lift the attachment off the ground to facilitate locking.
HAND LOCKING AND CONNECTING THE ATTACHMENT
- Take the locking pin and the clip on the bracket (Fig. A) and lock the attachment (Fig.
D). Do not forget to refit the clip.
- Stop the I.C. engine and keep the ignition on the lift truck.
- Remove the pressure of the attachment hydraulic circuit, to do so, press the button 1
(Fig. E) on the distributor lever and operate the lever 4 or 5 times from the left to the right.
- Connect the rapid connectors according to the logic of the attachment’s hydraulic movements.
Make sure that the rapid connectors are clean and protect the holes which are not used, with the caps provided.
HAND RELEASING AND DISCONNECTING THE ATTACHMENT
- Proceed in the reverse order of paragraph HAND LOCKING AND CONNECTING THE
ATTACHMENT while making sure you put back the locking pin and the clip in the bracket (Fig. A).
LAYING AN ATTACHMENT
- Proceed in the reverse order of paragraph TAKING UP AN ATTACHMENT while making sure you place the attachment flat on the ground and in closed position.
D
A
B
C
E
MT 845 Turbo MONO-ULTRA Série 2
MT 1233 S Turbo MONO-ULTRA Série 2
1st ASSEMBLY 2nd ASSEMBLY
1
1
E
MT 940/1240 L Turbo MONO-ULTRA Série 2
MT 1337 SL Turbo MONO-ULTRA Série 2
MT 1637 SL Turbo MONO-ULTRA Série 2
1st ASSEMBLY 2nd ASSEMBLY
1
1
4 - 11
INTRODUCTION TO SAFETY
F - H
YDRAULIC ATTACHMENT AND HYDRAULIC LOCKING DEVICE
(O
PTION
)
MT 845 Série 2 + Turbo
MT 940/1240 L Série 2 + Turbo
MT 1233 S Série 2 + Turbo
MT 1330/1740 SL Série 2 + Turbo
MT 1337/1637 SL Série 2 + Turbo
TAKING UP AN ATTACHMENT
- Ensure that the attachment is in a position facilitating the locking to the carriage. If it is not correctly oriented, take the necessary precautions in order to move it safely.
- Check that the rods on the locking cylinder are retracted (Fig. A).
- Place the lift truck with the jib lowered in front of and parallel to the attachment, tilt the carriage forwards (Fig. B).
- Bring the carriage under the locking tube of the attachment, slightly lift the jib, incline the carriage backwards in order to position the attachment (Fig. C).
- Lift the attachment off the ground to facilitate locking.
HYDRAULIC LOCKING AND CONNECTING THE ATTACHMENT
- Put the valve in position A (Fig. D), that is to say, the hydraulic circuit of the attachment locking open.
- Push the lever of the distributor 1 (Fig. E) forwards in order to completely lock the attachment on the carriage.
- Stop the engine.
- Remove the pressure of the attachment hydraulic circuit by using the lever of the distributor 1 (Fig. E).
- Connect the rapid connectors according to the logic of the attachment’s hydraulic movements.
Make sure that the rapid connectors are clean and protect the holes which are not used, with the caps provided.
- Close the valve in position B (Fig. D), that is to say, the hydraulic circuit of the attachment locking closed.
Always close the valve in position B (Fig. D) after the locking of the attachment, in order to avoid accidental unlocking and use the attachment safely.
HYDRAULIC RELEASING AND DISCONNECTING THE ATTACHMENT
- Close the attachment.
- Put the valve in position A (Fig. D), that is to say, the hydraulic circuit of the attachment locking open.
- Push the lever of the distributor 1 (Fig. E) backwards in order to completely unlock the attachment on the carriage.
- Stop the engine.
- Remove the pressure of the attachment hydraulic circuit by using the lever of the distributor 1 (Fig. E).
- Disconnect the rapid connectors of the attachment.
Make sure that the rapid connectors are clean and protect the holes which are not used, with the caps provided.
LAYING AN ATTACHMENT
- Proceed in the reverse order of paragraph TAKING UP AN ATTACHMENT while making sure you place the attachment flat on the ground and in closed position.
4 - 12
A
B
C
D
A
B
INTRODUCTION TO SAFETY
E
1
4 - 13
INTRODUCTION TO SAFETY
G - H
YDRAULIC ATTACHMENT AND HYDRAULIC LOCKING DEVICE
(O
PTION
)
MT 845 Turbo MONO-ULTRA Série 2
MT 940/1240 L Turbo MONO-ULTRA Série 2
MT 1233 S Turbo MONO-ULTRA Série 2
MT 1337/1637 SL Turbo MONO-ULTRA Série 2
TAKING UP AN ATTACHMENT
- Ensure that the attachment is in a position facilitating the locking to the carriage. If it is not correctly oriented, take the necessary precautions in order to move it safely.
- Check that the rods on the locking cylinder are retracted (Fig. A).
- Place the lift truck with the jib lowered in front of and parallel to the attachment, tilt the carriage forwards (Fig. B).
- Bring the carriage under the locking tube of the attachment, slightly lift the jib, incline the carriage backwards in order to position the attachment (Fig. C).
- Lift the attachment off the ground to facilitate locking.
HYDRAULIC LOCKING AND CONNECTING THE ATTACHMENT
- Put the valve in position A (Fig. D), that is to say, the hydraulic circuit of the attachment locking open.
- Press the button 1 (Fig. E) of the distributor lever and push the lever to the right so as to completely lock the attachment onto the carriage.
- Stop the I.C. engine and keep the ignition on the lift truck.
- Remove the pressure of the attachment hydraulic circuit, to do so, press the button 1
(Fig. E) on the distributor lever and operate the lever 4 or 5 times from the left to the right.
- Connect the rapid connectors according to the logic of the attachment’s hydraulic movements.
Make sure that the rapid connectors are clean and protect the holes which are not used, with the caps provided.
- Close the valve in position B (Fig. D), that is to say, the hydraulic circuit of the attachment locking closed.
Always close the valve in position B (Fig. D) after the locking of the attachment, in order to avoid accidental unlocking and use the attachment safely.
HYDRAULIC RELEASING AND DISCONNECTING THE ATTACHMENT
- Close the attachment.
- Put the valve in position A (Fig. D), that is to say, the hydraulic circuit of the attachment locking open.
- Press the button 1 (Fig. E) of the distributor lever and push the lever to the left so as to completely unlock the attachment.
- Stop the I.C. engine and keep the ignition on the lift truck.
- Remove the pressure of the attachment hydraulic circuit, to do so, press the button 1
(Fig. E) on the distributor lever and operate the lever 4 or 5 times from the left to the right.
- Disconnect the rapid connectors of the attachment.
Make sure that the rapid connectors are clean and protect the holes which are not used, with the caps provided.
LAYING AN ATTACHMENT
- Proceed in the reverse order of paragraph TAKING UP AN ATTACHMENT while making sure you place the attachment flat on the ground and in closed position.
4 - 14
A
B
C
D
A
B
INTRODUCTION TO SAFETY
E
MT 845 Turbo MONO-ULTRA Série 2
MT 1233 S Turbo MONO-ULTRA Série 2
1st ASSEMBLY 2nd ASSEMBLY
1
1
E
MT 940/1240 L Turbo MONO-ULTRA Série 2
MT 1337 SL Turbo MONO-ULTRA Série 2
MT 1637 SL Turbo MONO-ULTRA Série 2
1st ASSEMBLY 2nd ASSEMBLY
1
1
4 - 15
INTRODUCTION TO SAFETY
4 - 16
डाउनलोड
विज्ञापन