Lanner NCA-1040SE User Manual
Werbung
Werbung
Network Appliance Platforms
NCA-1040SE
User Manual
Version: 1.3
Date of Release: 2023-08-28
1
NCA-1040SE User Manual
This manual describes the overview of the various functionalities of this product, and the information you need to get it ready for operation. It is intended for those who are:
responsible for installing, administering and troubleshooting this system for Information Technology professionals.
assumed to be qualified in the servicing of computer equipment, such as professional system integrators, or service personnel and technicians.
The latest version of this document can be found on Lanner’s official website, available either through the product page or through the Lanner Download Center page with a login account and password.
The icons are used in the manual to serve as an indication of interest topics or important messages.
Icon Usage
Note or Information
This mark indicates that there is something you should pay special attention to while using the product.
Warning or Important
This mark indicates that there is a caution or warning and it is something that could damage your property or product.
To obtain additional documentation resources and software updates for your system, please visit the Lanner
Download Center . As certain categories of documents are only available to users who are logged in, please be registered for a Lanner Account at http://www.lannerinc.com/ to access published documents and downloadable resources.
In addition to contacting your distributor or sales representative, you could submit a request at our Lanner
Technical Support and fill in a support ticket to our technical support department.
Your feedback is valuable to us, as it will help us continue to provide you with more accurate and relevant documentation. To provide any feedback, comments or to report an error, please email [email protected]
. Thank you for your time.
This document is copyrighted © 2023 by Lanner Electronics Inc. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable. However, the original manufacturer assumes no responsibility for its use, nor for any infringements upon the rights of third parties that may result from such use.
2
NCA-1040SE User Manual
Taiwan Corporate Headquarters
Lanner Electronics Inc.
7F, No.173, Sec.2, Datong Rd.
Xizhi District, New Taipei City 22184,
Taiwan
立端科技股份有限公司
221 新北市汐止區
大同路二段 173 號 7 樓
T: +886-2-8692-6060
F: +886-2-8692-6101
USA
Lanner Electronics Inc.
47790 Westinghouse Drive
Fremont, CA 94539
T: +1-855-852-6637
F: +1-510-979-0689
Europe
Lanner Europe B.V.
Wilhelmina van Pruisenweg 104
2595 AN The Hague
The Netherlands
T: +31 70 701 3256
China
Beijing L&S Lancom Platform Tech. Co., Ltd.
Guodong LOFT 9 Layer No. 9 Huinan Road,
Huilongguan Town, Changping District, Beijing
102208 China
T: +86 010-82795600
F: +86 010-62963250
Canada
Lanner Electronics Canada Ltd
3160A Orlando Drive
Mississauga, ON
L4V 1R5 Canada
T: +1 877-813-2132
F: +1 905-362-2369
3
NCA-1040SE User Manual
Intel® and Intel® Celeron® are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
1.
An unshielded-type power cord is required in order to meet FCC emission limits and also to prevent interference to the nearby radio and television reception. It is essential that only the supplied power cord be used.
2.
Use only shielded cables to connect I/O devices to this equipment.
3.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
1.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
2.
This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules.
Follow these guidelines to ensure general safety:
Keep the chassis area clear and dust-free during and after installation.
Do not wear loose clothing or jewelry that could get caught in the chassis. Fasten your tie or scarf and roll up your sleeves.
Wear safety glasses if you are working under any conditions that might be hazardous to your eyes.
Do not perform any action that creates a potential hazard to people or makes the equipment unsafe.
Disconnect all power by turning off the power and unplugging the power cord before installing or removing a chassis or working near power supplies
Do not work alone if potentially hazardous conditions exist.
Never assume that power is disconnected from a circuit; always check the circuit.
Suivez ces consignes pour assurer la sécurité générale :
Laissez la zone du châssis propre et sans poussière pendant et après l’installation.
4
NCA-1040SE User Manual
Ne portez pas de vêtements amples ou de bijoux qui pourraient être pris dans le châssis. Attachez votre cravate ou
écharpe et remontez vos manches.
Portez des lunettes de sécurité pour protéger vos yeux.
N’effectuez aucune action qui pourrait créer un danger pour d’autres ou rendre l’équipement dangereux.
Coupez complètement l’alimentation en éteignant l’alimentation et en débranchant le cordon d’alimentation avant d’installer ou de retirer un châssis ou de travailler à proximité de sources d’alimentation.
Ne travaillez pas seul si des conditions dangereuses sont présentes.
Ne considérez jamais que l’alimentation est coupée d’un circuit, vérifiez toujours le circuit. Cet appareil génère, utilise et émet une énergie radiofréquence et, s’il n’est pas installé et utilisé conformément aux instructions des fournisseurs de composants sans fil, il risque de provoquer des interférences dans les communications radio.
There is risk of explosion if the battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
Installation should be conducted only by a trained electrician or only by an electrically trained person who knows all installation procedures and device specifications which are to be applied.
Do not carry the handle of power supplies when moving to another place.
Please conform to your local laws and regulations regarding safe disposal of lithium battery.
Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery can result in an explosion.
Leaving a battery in an extremely high temperature environment can result in an explosion or the leakage of flammable liquid or gas.
A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.
Risque d’explosion si la pile est remplacée par une autre d’un mauvais type.
Jetez les piles usagées conformément aux instructions.
L’installation doit être effectuée par un électricien formé ou une personne formée à l’électricité connaissant toutes les spécifications d’installation et d’appareil du produit.
Ne transportez pas l’unité en la tenant par le câble d’alimentation lorsque vous déplacez l’appareil.
Electrical equipment generates heat. Ambient air temperature may not be adequate to cool equipment to acceptable operating temperatures without adequate circulation. Be sure that the room in which you choose to operate your system has adequate air circulation.
Ensure that the chassis cover is secure. The chassis design allows cooling air to circulate effectively. An open chassis permits air leaks, which may interrupt and redirect the flow of cooling air from internal components.
Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. ESD damage occurs when electronic components are improperly handled and can result in complete or intermittent failures. Be sure to follow
ESD-prevention procedures when removing and replacing components to avoid these problems.
Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact. If no wrist strap is available, ground yourself by touching the metal part of the chassis.
Periodically check the resistance value of the antistatic strap, which should be between 1 and 10 megohms (Mohms).
L’équipement électrique génère de la chaleur. La température ambiante peut ne pas être adéquate pour refroidir l’équipement à une température de fonctionnement accept able sans circulation adaptée. Vérifiez que votre site propose une circulation d’air adéquate.
Vérifiez que le couvercle du châssis est bien fixé. La conception du châssis permet à l’air de refroidissement de bien circuler. Un châssis ouvert laisse l’air s’échapper, ce qui peut interrompre et rediriger le flux d’air frais destiné aux composants internes.
Les décharges électrostatiques (ESD) peuvent endommager l’équipement et gêner les circuits électriques. Des dégâts d’ESD surviennent lorsque des composants électroniques sont mal manipulés et peuvent causer des pannes totales ou intermittentes. Suivez les procédures de prévention d’ESD lors du retrait et du remplacement de composants.
5
NCA-1040SE User Manual
Portez un bracelet antiESD et veillez à ce qu’il soit bien au contact de la peau. Si aucun bracelet n’est disponible, reliez votre corps à la terre en touchant la partie métallique du châssis.
Vérifiez régulièrement la valeur de résistance du bracelet antistatique, qui doit être comprise entre 1 et 10 mégohms
(Mohms).
Mounting Installation Precautions
The following should be put into consideration for rack-mount or similar mounting installations:
Do not install and/or operate this unit in any place that flammable objects are stored or used in.
The installation of this product must be performed by trained specialists; otherwise, a non-specialist might create the risk of the system’s falling to the ground or other damages.
Lanner Electronics Inc. shall not be held liable for any losses resulting from insufficient strength for supporting the system or use of inappropriate installation components.
Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of airflow required for safe operation of the equipment is not compromised.
Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.
Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.
Reliable Grounding - Reliable grounding of rack mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).
Installation & Operation
This equipment must be grounded. The power cord for product should be connected to a socket-outlet with earthing connection.
Cet équipement doit être mis à la terre. La fiche d'alimentation doit être connectée à une prise de terre correctement câblée
Suitable for installation in Information Technology Rooms in accordance with Article 645 of the National Electrical Code and NFPA 75.
Peut être installé dans des salles de matériel de traitement de l'information conformément à l'article 645 du National
Electrical Code et à la NFPA 75.
The machine can only be used in a restricted access location and must be installed by a skilled person.
Les matériels sont destinés à être installés dans des EMPLACEMENTS À ACCÈS RESTREINT.
Some USB devices may not be compatible with the system. If you encounter an error, please remove the USB device and restart the system.
Warning
Class I Equipment. This equipment must be earthed. The power plug must be connected to a properly wired earth ground socket outlet. An improperly wired socket outlet could place hazardous voltages on accessible metal parts.
Product shall be used with Class 1 laser device modules.
Avertissement
Équipement de classe I. Ce matériel doit être relié à la terre. La fic he d’alimentation doit être raccordée à une prise de terre correctement câblée. Une prise de courant mal câblée pourrait induire des tensions dangereuses sur des parties métalliques accessibles.
Le produit doit être utilisé avec des modules de dispositifs laser de classe 1.
6
NCA-1040SE User Manual
Before turning on the device, ground the grounding cable of the equipment. Proper grounding (grounding) is very important to protect the equipment against the harmful effects of external noise and to reduce the risk of electrocution in the event of a lightning strike. To uninstall the equipment, disconnect the ground wire after turning off the power. A ground wire (green-and-yellow) is required and the part connecting the conductor must be greater than 4 mm2 or 10
AWG.
Avant d’allumer l’appareil, reliez le câble de mise à la terre de l’équipement à la terre.
Une bonne mise à la terre (connexion à la terre) est très importante pour protéger l’équipement contre les effets néfastes du bruit externe et réduire les risques d’ électrocution en cas de foudre.
Pour désinstaller l’équipement, débranchez le câble de mise à la terre après avoir éteint l’appareil.
Un câble de mise à la terre est requis et la zone reliant les sections du conducteur doit faire plus de 4 mm2 ou 10 AWG.
Connect the grounding cable to the ground.
The protection device for the DC power source must provide 30 A current.
This protection device must be connected to the power source before DC power.
Branchez le câble de mise à la terre à la terre.
L’appareil de protection pour la source d’alimentation CC doit fournir 30 A de courant.
Cet appareil de protection doit être branché à la source d’alimentation avant l’alimentation CC.
7
NCA-1040SE User Manual
8
NCA-1040SE User Manual
9
NCA-1040SE User Manual
NCA-1040SE is a compact desktop appliance empowered by Intel® Atom® x6413E / Intel® Celeron®
N6210/J6412 ( codenamed Elkhart lake) processor. The NCA1040SE’s form factor, relatively low power consumption, robust processing capability, up to 32GB DDR4 3200MHz SODIMM and its various I/O ports together make it ideal for edge deployments, branch offices and retail settings.
Your package contains the following items:
1x NCA-1040SE Network Security Platform
1x Power Adaptor
1x Power Cable
1x Console Cable
4x Rubber Foot
SKU No.
NCA-1040SEA
NCA-1040SEB
NCA-1040SEC
Main Features
4-core 1.5GHz, Intel® Atom® X6413E (Elkhart Lake), 4x 2.5GbE RJ45, 1x DDR4
SO-DIMM, 1x PoE+, 1x TPM, Wi-Fi/LTE/5G Module Support, 40W Adapter
4-core 2.0GHz, Intel® Celeron® J6412 (Elkhart Lake), 4x 2.5GbE RJ45, 1x DDR4
SO-DIMM, 1x PoE+, 1x TPM, Wi-Fi/LTE/5G Module Support, 40W Adapter
2-core 1.2GHz, Intel® Celeron® N6210 (Elkhart Lake), 4x 2.5GbE RJ45, 1x DDR4
SO-DIMM, 40W Adapter
Model
5G Kit
LTE Kit
Wi-Fi Kit
5G Module Card and Antenna Kit
Description
LTE Module Card, and Antenna Kit
Wi-Fi Module Card, and Antenna Kit
PoE Kit PoE+ Power Adapter Kit
Rackmount Kit 1U Rackmount kit (long ear bracket with adapter holder, 2-sided design)
Wall Mount Kit Wall Mount Kit for NCA-1040
Note: If you seek any specific compatible components or kits, please contact your dealer for assistance.
10
NCA-1040SE User Manual
Form Factor
Platform
BIOS
Networking
I/O Interface
Storage
Expansion
System Memory
PoE+ Support
Processor Options
Frequency
CPU Cores
Chipset
Technology
Max. Capacity
Socket
Controller
Interface
Bypass
# of PoE+ (PSE) Ports
Standard
PoE+ Power Input
Reset Button
LED Indicators
Power Button
Console Port
USB Port
Display Port
Power Input
Antenna Hole
Onboard Slots
Mini-PCIe
SIM Card Slot
Watchdog
Miscellaneous
Cooling
Environmental
Mechanical
Power
OS Support
Approvals and Compliance
Internal RTC with Li Battery YES
TPM
Processor
System
Temperature
Humidity (RH)
(WxDxH)
Weight
Mounting
Type/Watts
Input
SKU A/B: YES
SKU C: N/A
Passive CPU Heatsink
Fanless (Default), 1x 5-pin Fan Connector (By Project)
0~40ºC Operating, -20~70ºC Non-Operating
5~90% Operating, 5~ 95% Non-Operating
183 x 32 x 168mm
0.9 kg
Rackmount; Wall Mount (Optional Kit)
1x 40W Power Adapter
AC 100~240V @50~60 Hz
Linux, Yocto
RoHS, CE/FCC Class B (Class A with PoE), UL, VCCI, UKCA
11
Fanless Desktop
SKU A: Intel® Atom® X6413E (Elkhart Lake)
SKU B: Intel® Celeron® J6412 (Elkhart Lake)
SKU C: Intel® Celeron® N6210 (Elkhart Lake)
1.5GHz/2.0GHz/1.2GHz
4 / 4 / 2
SoC
AMI SPI Flash BIOS
DDR4 3200MT/s SO-DIMM
Up to 32 GB
1x 260pin SO-DIMM
Intel® i226V
4x 2.5GbE RJ45 Ports;
N/A
SKU A/B: 1x PoE+ Port
SKU C: N/A
IEEE 802.3at
4-pin power connector with 65W PoE+ adapter
1x Reset Button
Power/Status/Storage/M.2/Mini PCIe, refer to Appendix A
1x Power Button with LED
1x RJ45 (Default Bard rate : 115200) Console Port
1x USB 3.0 Port
1x Display Port (without Audio Function)
1x DC Jack with Lock
4x Antenna Holes for Wi-Fi/LTE/5G (SKU A/B Only)
1x M.2 (SATA) 2280 B-Key
SKU A/B : 1x Mini-PCIe (PCIe/USB2.0) for Wi-Fi ;
1x M.2 3042/3052 B-Key for 5G/LTE
SKU C : N/A
SKU A/B : 2x Nano SIM Card Slots
SKU C : N/A
YES
NCA-1040SE User Manual
No.
F1
F2
F3
F4
F5
F2
F3
F4
F5
F1 F1
Antennas
Reset Button
LED Indicators
Console Port
USB Port
Description
2x SMA Antenna Holes (SKU A/B Only: Support Wi-Fi/LTE/5G Module)
1x Reset Button
Power/Status/Storage/M.2/Mini-PCIe, refer to Appendix A
1x RJ45 Console Port
1x USB 3.0 Port
12
NCA-1040SE User Manual
No.
R1
R2
R3
R4
R5
R6
R1
R2
R3 R4
R5
R6
R1
Antennas
Power Button
Power Inlet
PoE+ (PSE) Port
LAN Ports
Display Port
Description
2x SMA Antenna Holes (SKU A/B Only: Support Wi-Fi/LTE/5G Module)
1x Power Button with LED
1x DC Jack with Lock
1x 4-pin 54V Input Port with Lock (ATX4P) for PoE+ (Optional, SKU A/B Only)
4x 2.5GbE RJ45 Ethernet Ports with LED
1x Display Port (without Audio Function)
13
NCA-1040SE User Manual
The following displays the connectors and jumpers on the motherboard layout.
14
NCA-1040SE User Manual
The following references the pin assignments and internal connectors of NCA-1040SE.
JCOMS1: RTC Reset
Pin
1-2
2-3
Description
Clear RTC_TEST
Clear RTC_RST
1
2
3
J8: Reset Option
Pin
1-2
2-3 (Default)
Description
Hardware Reset
Software Reset
1
2
3
PW2: Power Supply Connector of PSE
Pin Description
1
2
3
GND
GND
+P54V
4 +P54V
JPW1: SATA Power Connector 1x4 Pins 2.54mm
Pin
1
Description
+P12V_S
4
1
2
3
4
GND
GND
+P5V_S
LAN1: 1x4 RJ45 w/o transformer
Pin Description
3
4
1
2
5
6
7
8
MD0+
MD0-
MD1+
MD2+
MD2-
MD1-
MD3+
MD3-
8
4 3 2 1
1
15
4
5
6
7
Pin
1
2
3
8
9
10
NCA-1040SE User Manual
COM1: RJ45 Console
Pin
1
Description
Request to Send (RTS)
6
7
8
2
3
4
5
NC
Transmitted Data (TxD)
Signal Ground
Signal Ground
Received Data (RxD)
NC
Clear to Send (CTS)
USB1: USB 3.0 single CONN
Pin Description
3
4
1
2
+P5V_USB1
USB20_N1
USB20_P1
GND
5
6
7
USB30_RXN0
USB30_RXP0
GND
8
9
USB30_TXN0
USB30_TXP0
DP1: Display Port 20P 0.6mm
Description
DP1_C_DATAP0
GND
DP1_C_DATAN0
DP1_C_DATAP1
GND
DP1_C_DATAN1
DP1_C_DATAP2
GND
DP1_C_DATAN2
DP1_C_DATAP3
14
15
16
17
Pin
11
12
13
18
19
20
Description
GND
DP1_C_DATAN3
DDI1_AUX_EN_P13
CONFIG2
DDI1_DDC_CLK_AUX_DP
GND
DDI1_DDC_DAT_AUX_DN
DP1_HPD
GND
+P3V3_DP
16
8 1
11
12
13
14
7
8
9
10
Pin
1
2
3
4
5
6
15
16
17
NCA-1040SE User Manual
SIM1/2: Nano SIM push-push
Pin Description
3
4
5
1
2
UIMx_PWR
UIMx_RST#
UIMx_CLK
UIMx_DETECT
GND
6
7
NC
UIMx_DAT
SATA1:180
°
SATA Connector
Pin
1
2
3
Description
GND
TX+
TX-
4
5
6
7
PCIE1: MiniPCIe Socket
GND
RX-
RX+
GND
Description
NC, PMC_WAKE#
+P3V3_S
NC
GND
NC
+P1V5_S
PCIE_CLKREQ5#
NC
GND
NC
REFCLK-
NC
REFCLK+
NC
GND
NC
NC
37
38
39
40
33
34
35
36
Pin
27
28
29
30
31
32
41
42
43
Description
GND
+P1V5_S
GND
NC, SMB_CLK
PCIE_TXN
NC, SMB_DATA
PCIE_TXP
GND
GND
USB20_N0
GND
USB20_P0
+P3V3_S
GND
+P3V3_S
NC
GND
17
NCA-1040SE User Manual
37
39
41
43
29
31
33
35
45
47
49
51
15
17
19
21
23
25
27
5
7
1
3
9
11
13
18
19
20
21
22
23
GND
NC
PH, +P3V3_S
GND
MPCIE_RST#
PCIE_RXN
24
25
26
+P3V3_S
PCIE_RXP
GND
M2_1: M.2 B-Key for Storage
Pin Description
B-KEY
B-KEY
B-KEY
NC
NC
NC
GND
NC
GND
GND
NC
NC
GND
B-KEY
NC
NC
GND
NC
NC
GND
SATA_C_RXP0
SATA_C_RXN0
GND
SATA_C_TXN0
SATA_C_TXP0
GND
38
40
42
44
30
32
34
36
46
48
50
52
16
18
20
22
10
12
14
24
26
28
Pin
2
4
6
8
44
45
46
47
48
49
50
51
52
LED_WLAN_N
NC
NC
NC
+P1V5_S
NC
GND
NC
+P3V3_S
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
Description
+P3V3_S
+P3V3_S
NC
NC
NC
B-KEY
B-KEY
B-KEY
B-KEY
NC
NC
NC
NC
NC
18
NCA-1040SE User Manual
31
33
35
37
23
25
27
29
39
41
43
45
53
55
57
59
61
63
65
67
69
71
NC
NC
GND
NC
NC
NC
NC
NC
GND
GND
9
11
13
15
3
5
7
17
19
21
73
75
GND
NC
74
M2_B_KEY1: M.2 B-Key for 4G/5G
Pin
1
Description
NC
Pin
2
GND
GND
USB2_DP0
USB2_DN0
GND
B-KEY
B-KEY
B-KEY
B-KEY
GND
10
12
14
16
4
6
8
18
20
22
54
56
58
60
62
64
66
68
70
72
NC, WAKE_UP#
DPR
GND
M2_USB30_TXN2
M2_USB30_TXP2
GND
M2_USB30_RXN2
M2_USB30_RXP2
GND
M2_PCIE_RXN1
M2_PCIE_RXP1
GND
32
34
36
38
24
26
28
30
40
42
44
46
Description
+P3V3_A
+P3V3_A
PH ,+P1V8_A
PH, +P3V3_A
LED_M2_WWAN_N
B-KEY
B-KEY
B-KEY
B-KEY
PH ,+P1V8_A
PH, +P3V3_A
NC
PH, +P3V3_A
NC
UIM1_RST#
UIM1_CLK
UIM1_DAT
UIM1_PWR
NC
UIM2_DETECT
UIM2_DAT
UIM2_CLK
UIM2_RST#
19
NC
NC
NC
NC
NC
NC
NC
NC
+P3V3_S
+P3V3_S
+P3V3_S
NCA-1040SE User Manual
47
49
51
59
61
63
65
53
55
57
67
69
71
M2_PCIE_TXN1
M2_PCIE_TXP1
GND
M2_PCIE_CLKN
M2_PCIE_CLKP
GND
NC
NC
NC
NC
NC, M2_RESET#
GND
GND
48
50
52
54
56
58
60
62
64
66
68
70
72
73
75
GND
NC
74
JFAN1: DIP 2.54mm 5-Pin Fan Connector
Pin Description
1
2
3
4
5
GND
TX+
TX-
GND
RX-
UIM2_PWR
NC, PCIE_B_RST#
NC,
M2_PCIE_CLKREQ1#
NC, B_WAKE#
NC
NC
NC
NC
NC
UIM1_DETECT
NC
+P3V3_A
+P3V3_A
+P3V3_A
6 RX+
7 GND
JUSBDOM1: DIP 2.54mm 2x5 Box Header R/A Type
Pin
1
2
3
Description
+P5V_USB2
NC
4
5
6
7
USB20_L_N
NC
USB20_L_P
NC
8
9
10
GND
NC
NC,USB_R_WP
NC
20
1 5
NCA-1040SE User Manual
JDI01: DIP 2.0mm 2x3 Pin Header
Pin Description
1
2
DIO_GPI_1
DIO_GPO_1
3
4
5
DIO_GPI_2
DIO_GPO_2
GND
6 GND
JSPI1: SMD 2.0mm 2x5 Pin Header
Pin
1
3
5
7
9
Description
SPI0_IO3_HOLD#
SPI0_CS0_R#
SPI0_IO1_MISO_R
NC
GND
Pin
2
4
6
8
10
Description
NC
V_3P3_SPI
NC
SPI0_CLK_R
SPI0_IO0_MOSI_R
J2: DIP 2.43mm 1x3 Pin Header for VCCIN debug
Pin
1
Description
SMB_DATA_VR
2
3
SMB_CLK_VR
GND
21
NCA-1040SE User Manual
To reduce the risk of personal injury, electric shock, or damage to the system, please remove all power connections to shut down the device completely and wear ESD protection gloves when handling the installation steps.
1. Power off the system and remove all power connections.
2. Turn the system upside down, with its bottom side facing up, and locate the four footing screws.
3. Remove the four (4) screws.
4. Turn the system right side up and gently lift the top chassis up.
22
NCA-1040SE User Manual
The motherboard supports a DIMM DDR4 3200MHz non-ECC up to 32GB, which is located on the bottom side of the motherboard. Please follow the steps below to install the DIMM memory module properly.
1. Power off the system.
2. Turn the system upside down, with its bottom side facing up.
3. Locate the DIMM socket cover.
4. Unscrew the one (1) screw securing the cover. And gently lift up the DIMM socket cover.
5. Align the notch of the DIMM card with the socket key in the pin slot.
6. Insert the DIMM card at 30 degrees into the socket until it is fully seated.
7. Push down on the module card until the slot latches catches and clicks into place.
Click
Notch
Click
23
NCA-1040SE User Manual
The system supports one M.2 slot for additional data storage (SSD is recommended due to heat and vibration concerns). Please follow the steps for installation.
1. Power off the system and open the chassis cover.
2. Locate the M.2 slot on the motherboard.
3. Align the notch of the M.2 memory card with the socket key in the pin slot.
4. Insert the M.2 memory card pins at 30 degrees into the socket until it is fully seated.
5. Push down on the module card and secure it with a screw.
Notch
24
NCA-1040SE User Manual
The motherboard provides one M.2 slot for LTE/5G module card. Please follow the procedures for installation.
LTE module requires two antennas, and 5G module requires four antennas.
1. Power off the system and open the chassis cover.
2. Locate the M.2 slot on the motherboard.
3. Align the notch of the 5G module card with the socket key in the pin slot.
4. Insert the 5G module card pins at 30 degrees into the socket until it is fully seated.
5. Push down on the module card and secure it with a screw.
Notch
25
NCA-1040SE User Manual
Installing 5G Antennas
Front Panel Rear Panel
A3 A4 A1
1.
Locate the four (4) antenna RF cables. Locate the four (4) IPEX connectors on the 5G module card.
A1
2.
Connect RF cables to the 5G module card.
A3
26
A2
A2
NCA-1040SE User Manual
3.
Screw on the four (4) antennas to the system.
A4
27
NCA-1040SE User Manual
The system supports one mini-PCIe slot for a Wi-Fi or BT module card. Please follow the steps to install the
Wi-Fi module card. Wi-Fi module requires two antennas.
1. Power off the system and open the chassis cover.
2. Locate the mPCIe slot on the motherboard.
3. Align the notch of the Wi-Fi module card with the socket key in the pin slot.
4. Insert the Wi-Fi module card pins at
30 degrees into the socket until it is fully seated.
5. Push down on the module card and secure it with a screw.
Notch
28
NCA-1040SE User Manual
Installing Wi-Fi Antennas
Rear Panel
A1
1.
Locate the two (2) antenna RF cables. Locate the two (2) IPEX connectors on the Wi-Fi module card
2.
Connect the RF cables to the Wi-Fi module card.
3.
Screw on the two (2) antennas to the system.
A1
29
A2
A2
NCA-1040SE User Manual
T he SIM slot on the bottom panel supports the LTE/5G module card. Please follow the steps below for SIM card placement.
1. Power off the system.
2. Turn the system upside down, with its bottom side facing up.
3. Locate the SIM slot cover.
4. Unscrew the one (1) screw securing the cover. And gently remove the SIM slot cover.
5. Insert and push the nano-SIM card all the way in until it clicks into place.
6. To remove the SIM card, use your fingertips to push it once, to have the card automatically eject.
7. Place the slot door back and tighten the one (1) screw.
30
NCA-1040SE User Manual
BIOS (Basic Input / Output System) is the program that controls the computer boot process.
BIOS is a firmware embedded on an exclusive chip on the system’s motherboard. Lanner's BIOS firmware offering including market-proven technologies such as Secure Boot and Intel Boot Guard technology deliver solid commitments for the shield protection against malware, uncertified sequences and other named cyber threats.
To enter the BIOS setup utility, simply follow the steps below:
1.
Boot up the system.
2.
Pressing the <Tab> or <Del> key immediately allows you to enter the Setup utility, and then you will be directed to the BIOS main screen. The instructions for BIOS navigations are as below:
Control Keys
→
<Enter>
+/-
F1
F2
F3
F4
<Esc>
Description select a setup screen select an item/option on a setup screen select an item/option or enter a sub-menu adjust values for the selected setup item/option display General Help screen retrieve previous values, such as the last configured parameters during the last time you entered BIOS load optimized default values save configurations and exit BIOS exit the current screen
Note : The images in the following section are for reference only.
31
NCA-1040SE User Manual
Setup main page contains BIOS information and project version information.
Feature
BIOS Information
Description
BIOS Vendor: American Megatrends
Core Version: AMI Kernel version, CRB code base, X64
Compliancy: UEFI version, PI version
Project Version: BIOS release version
Build Date and Time: MM/DD/YYYY
Access Level: Administrator / User
FSP Information FSP version: Intel FSP binary version.
System Date
System Time
RC version: Intel reference code version.
To set the Date, use <Tab> to switch between Date elements. Default
Range of Year: 2005-2099
Default Range of Month: 1-12
Days: dependent on Month.
To set the Date, use <Tab> to switch between Date elements.
32
NCA-1040SE User Manual
Select the Advanced menu item from the BIOS setup screen to enter the “Advanced” setup screen. Users can select any of the items in the left frame of the screen.
33
NCA-1040SE User Manual
Feature
Hardware
Prefetcher
Adjacent Cache
Line Prefetch
Intel (VMX)
Virtualization Technology
AES
MonitorMWait
AC Split Lock
Options
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Description
To turn ON/OFF the MLC streamer prefetcher
To turn ON/OFF prefetching of adjacent cache lines.
Intel (VMX) Virtualization Technology
Enable/Disable AES (Advanced Encryption Standard)
Enable/Disable MonitorMWait
Enable/Disable AC Split Lock
34
NCA-1040SE User Manual
Feature
Boot Performance
Mode
I ntel® SpeedStep™
RC6
(Render Standby)
Disable Turbo
GT Frequency
Options
Max Battery
Max
Non-Turbo Performance
Turbo Performance
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Description
Select the performance state that the BIOS will set starting from reset vector.
Allows more than two frequency ranges to be supported.
Check to enable render standby support.
Enabled: Disables Turbo GT frequency.
Disabled: GT frequency is not limited.
35
NCA-1040SE User Manual
Feature
Me FW Image
Re-Flash
Options
Enabled
Disabled
Description
Enable/Disable ME FW Update function.
36
NCA-1040SE User Manual
Feature
Security Device
Support
SHA-1 PCR Bank
SHA256 PCR Bank
Pending Operation
Platform Hierarchy
Storage Hierarchy
Endorsement
Hierarchy
Options
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
None
TPM Clear
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Description
Enables or disables BIOS support for security device. By disabling this function, OS will not show Security Device. TCG
EFI protocol and INT1A interface will not be available.
Enables or disables SHA-1 PCR Bank.
Enables or disables SHA256 PCR Bank
Schedules an Operation for the Security Device.
NOTE: Your computer will reboot during restart in order to change State of Security Device.
Enables or disables Platform Hierarchy.
Enables or disables Storage Hierarchy
Enables or disables Endorsement Hierarchy.
37
NCA-1040SE User Manual
Feature
Control Legacy PXE
Boot From
Options
Disabled
LAN1
LAN2
LAN3
LAN4
Description
Control PXE Boot from which LAN.
38
NCA-1040SE User Manual
Feature
Serial Port
Device Settings
Options
Enabled
Disabled
NA
Description
Enables or Disables Serial Port 1
IO=3F8h; IRQ=4
39
NCA-1040SE User Manual
40
NCA-1040SE User Manual
Feature
Console Redirection
Options
Enabled
Disabled
Description
Enables or Disables Console Redirection
41
NCA-1040SE User Manual
Feature
Terminal Type
Bits per second
Data Bits
Parity
Stop Bits
Options
VT100
VT100+
VT-UTF8
ANSI
9600
19200
38400
57600
115200
7
8
None
Even
Odd
Mark
Space
1
2
Description
VT100: ASCII char set
VT100+: Extends VT100 to support color, function keys, etc.
VT-UTF8: Uses UTF8 encoding to map Unicode chars onto 1 or more bytes
Selects serial port transmission speed. The speed must be matched on the other side. Long or noisy lines may require lower speeds.
Data Bits
A parity bit can be sent with the data bits to detect some transmission errors.
Indicates the end of a serial data packet.
42
NCA-1040SE User Manual
Flow Control
VT-UTF8 Combo
Key Support
Recorder Mode
Resolution 100x31
Putty KeyPad
None
Hardware
RTS/CTS
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
VT100
LINUX
XTERM86
SCO
ESCN
VT400
Flow Control can prevent data loss from buffer overflow.
Enables VT-UTF8 Combination Key Support for ANSI/VT100 terminals
With this mode enabled, only text will be sent. This is to capture Terminal data
Enables or disables extended terminal resolution
Selects FunctionKey and Keypad on Putty
43
NCA-1040SE User Manual
Feature
SR-IOV Support
Options
Disabled
Enabled
Description
If the system has SR-IOV capable PCIe Devices, this option enables or disables Single Root IO Virtualization Support.
44
NCA-1040SE User Manual
Feature
Legacy USB
Support
XHCI Hand-off
USB Mass Storage
Driver Support
USB transfer time-out
Device reset time-out
Device power-up delay
Description
Enables Legacy USB support.
Auto option disables legacy support if no USB devices are connected;
Disabled option will keep USB devices available only for EFI applications
This is a workaround for OSes without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver.
Enables or disables USB Mass Storage Driver Support
Options
Enabled
Disabled
Auto
Enabled
Disabled
Enabled
Disabled
1 sec
5 sec
10 sec
20 sec
1 sec
5 sec
10 sec
20 sec
Auto
Manual
The time-out value for Control, Bulk, and Interrupt transfers
USB mass storage device Start Unit command time-out
Maximum time the device will take before it properly reports itself to the
Host Controller. Auto uses default value: for a Root port, it is 100ms, for a Hub port the delay is taken from Hub descriptor.
45
NCA-1040SE User Manual
Feature
Network Stack
IPv4 PXE Support
IPv4 HTTP Support
IPv6 PXE Support
IPv6 HTTP Support
PXE boot wait time
Media detect count
Options
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
0
1
Description
Enables or disables UEFI Network Stack
Enables IPv4 PXE Boot Support. If IPv4 is disabled, PXE boot option will not be created.
Enables IPv4 HTTP Boot Support. If IPv4 is disabled, HTTP boot option will not be created.
Enables IPv6 PXE Boot Support. If IPv6 is disabled, PXE boot option will not be created.
Enables IPv6 HTTP Boot Support. If IPv6 is disabled, HTTP boot option will not be created.
Wait time to press <ESC> key to abort the PXE boot
Number of times the presence of media will be checked.
46
NCA-1040SE User Manual
47
NCA-1040SE User Manual
Feature
VT-d
X2APIC
Opt Out
Options
Disable
Enable
Disable
Enable
Description
VT-d capability.
Option to Enable/Disable VT-d.
Enable/Disable X2APIC_OPT_OUT
48
NCA-1040SE User Manual
Feature
SATA Controller(s)
SATA Mode
Selection
Options
Disabled
Enabled
AHCI
Description
Enables/Disables SATA controller
SATA mode support.
49
NCA-1040SE User Manual
Select the Security menu item from the BIOS setup screen to enter the Security Setup screen. Users can select any of the items in the left frame of the screen.
Feature
Administrator Password
User Password
Description
I f ONLY the Administrator’s password is set, it only limits access to Setup and is only asked for when entering Setup.
I f ONLY the User’s password is set, it serves as a power -on password and must be entered to boot or enter Setup. In Setup, the User will have Administrator rights.
50
NCA-1040SE User Manual
Feature
Secure Boot
Secure Boot
Mode
Options
Disabled
Enabled
Standard
Custom
Description
Secure Boot is activated when Platform Key (PK) is enrolled, System mode is User/Deployed, and CSM function is disabled.
Customizable Secure Boot mode: In Custom mode,
Secure Boot Policy variables can be configured by a physically present user without full authentication.
51
NCA-1040SE User Manual
Feature
Factory Key
Provision
Restore Factory Keys
Enroll Efi Image
Options
Disabled
Enabled
None
None
Description
Provision factory default keys on next re-boot only when
System in Setup Mode.
Force System to User Mode. Configure NVRAM to contain
OEM-defined factory default Secure Boot keys.
Allows the image to run in Secure Boot mode. Enroll SHA
256 hash of the binary into Authorized Signature
Database (db)
52
NCA-1040SE User Manual
Select the Boot menu item from the BIOS setup screen to enter the Boot Setup screen. Users can select any of the items in the left frame of the screen.
Feature
Setup Prompt
Timeout
Bootup NumLock
State
Options
5
ON
OFF
Description
The number of seconds to wait for setup activation key.
65535 means indefinite waiting
Select the keyboard NumLock state
Choose boot priority from boot option group.
Choose specifies boot device priority sequence from available Group device.
53
NCA-1040SE User Manual
Select the Save and Exit menu item from the BIOS setup screen to enter the Save and Exit Setup screen. Users can select any of the items in the left frame of the screen.
■ Save Changes and Rest
When Users have completed the system configuration changes, select this option to save the changes and exit from BIOS Setup in order for the new system configuration parameters to take effect. The following window will appear after selecting the “Save Changes and Exit” option is selected. Select “Yes” to Save
Changes and Exit Setup.
■ Discard Changes and Exit
Select this option to quit Setup without saving any modifications to the system configuration. The following window will appear after the “Discard Changes and Exit” option is selected. Select “Yes” to Discard changes and Exit Setup.
54
NCA-1040SE User Manual
■ Restore Defaults
Restore default values for all setup options. Select “Yes” to load Optimized defaults.
Note: The items under Boot Override may not have the same image. It would depend on the devices connected to the system.
55
NCA-1040SE User Manual
APPENDIX A: LED INDICATOR EXPLANATIONS
Power / Status / Storage / M.2 / mPCIe LED
LED
Power
Status
Storage
M.2 mPCIe
COLOR
Green
OFF
Green
LED ACTION
Steady
N/A
Steady
DESCRIPTION
System is powered ON
System is powered OFF
System is Active
Red
OFF
Steady
N/A
System Error
System is powered OFF
Note: Status bi-color LED controlled by GPIO
Yellow Blinking Storage (SATA/NVME) Active
OFF N/A No Data Access
LED behavior will be determined by the inserted module card (optional)
LED behavior will be determined by the inserted module card (optional)
56
NCA-1040SE User Manual
TERMS AND CONDITIONS
1.
All products are under warranty against defects in materials and workmanship for a period of one year from the date of purchase.
2.
The buyer will bear the return freight charges for goods returned for repair within the warranty period; whereas the manufacturer will bear the after-service freight charges for goods returned to the user.
3.
The buyer will pay for repair (for replaced components plus service time) and transportation charges (both ways) for items after the expiration of the warranty period.
4.
If the RMA Service Request Form does not meet the stated requirement as listed on “ RMA Service, “RMA goods will be returned at customer ’ s expense.
5.
The following conditions are excluded from this warranty:
Improper or inadequate maintenance by the customer
Unauthorized modification, misuse, or reversed engineering of the product
Operation outside of the environmental specifications for the product.
1.
To obtain an RMA number, simply fill out and fax the “ RMA Request Form “ to your supplier.
2.
The customer is required to fill out the problem code as listed. If your problem is not among the codes listed, please write the symptom description in the remarks box.
3.
Ship the defective unit(s) on freight prepaid terms. Use the original packing materials when possible.
4.
Mark the RMA# clearly on the box.
Note : Customer is responsible for shipping damage(s) resulting from inadequate/loose packing of the defective unit(s). All RMA# are valid for 30 days only; RMA goods received after the effective
RMA# period will be rejected.
57
NCA-1040SE User Manual
When requesting RMA service, please fill out the following form. Without this form enclosed, your RMA cannot be processed.
58
Herunterladen
Öffentlicher Link aktualisiert
Der öffentliche Link zu Ihrem Chat wurde aktualisiert. Sie können Ihre Chat-Links nach der Registrierung hier einsehen und verwalten.
Öffentlicher Dokumentenlink
Werbung