Owner’s Manual & Safety Instructions

Save This Manual

Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference. 17h

Visit our website at: http://www.harborfreight.com

Email our technical support at: [email protected]

When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-888-866-5797 as soon as possible.

Copyright © 2015 by Harbor Freight Tools ® . All rights reserved.

No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.

Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein.

Tools required for assembly and service may not be included.

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

IMPORTANT SAFETY INSTRUCTIONS!

READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT!

Safety Warnings and Precautions

WARNING: When using product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment.

Read all instructions before using this product!

1. Keep work area clean . Cluttered areas invite injuries.

2. Observe work area conditions . Keep work area well lighted.

3. Store idle equipment . When not in use, the Service Cart must be stored in a safe and clean location. Always lock up products and keep out of reach of children.

4. Use the right product for the job . There are certain applications for which the

Service Cart was designed. Do not modify the Service Cart and do not use the Service

Cart for a purpose for which it was not intended.

5. Check for damaged parts . Before using any product, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for any broken or damaged parts and any other conditions that may affect its operation. Replace or repair damaged or worn parts immediately.

6. Replacement parts and accessories . When servicing, use only identical replacement parts. Use of any other parts will void the warranty.

7. Do not operate product if under the influence of alcohol or drugs . Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the product.

8. Use eye protection . Always wear ANSI approved impact safety goggles.

9. Do not exceed the product’s maximum load capacity of 500 lb.

10. Only use on a flat surface capable of supporting the Service Cart and its maximum capacity load of 500 lb. It is easy to lose control of the Service Cart if attempting to pull a load on a sloping or uneven surface.

11. Do not allow children to play on, stand upon or climb on the Service Cart. The

Service Cart is not for carrying people or animals.

12. Always check hardware and assembled parts after assembling. All connections should be tight and hardware tightened.

13. Always distribute objects in the Service Cart evenly. Uneven weight distribution could cause tipping. Do not lean or climb on the Service Cart.

Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.

SKU 62703 For technical questions please call 1-888-866-5797. Page 2

Specifications

Maximum Capacity

Tray Size

Casters

ASSEMBLY

500 lb.

36″ L x 24″ W x 3″ Deep

2 fixed and 2 swivel, 5″ diameter x 1″ Wide, Casters

Your Service Cart will require complete assembly. It is important that you read the entire manual to become familiar with the product BEFORE you assemble and use the Service

Cart. Before operating the Service Cart be sure that you have all parts described in the

Parts List and Assembly Diagram located on the last pages of this manual. Refer to the

Assembly Diagram on page 7 when assembling this product.

1. Place one Table Board (2) upside down on the work surface. Locate the Handle (3).

Turn it upside down with the cup holder toward the Table Board and the hand holes on the outside. Using a rubber mallet, tap the Handle down into the grooves on the Table

Board. Slide Rod (11) into handle to secure in place. - see Assembly diagram.

2. Locate two Legs (4). Place one on the Table Board (2) corner nearest the Handle (3), and place one on the diagonal corner located on the outside of the Table Board as in the Assembly diagram. Make certain that the end with the screw holes is facing upward. Using a rubber mallet, tap the Legs (4) down into the Table Board.

Note: Position the Legs so that the flange in each matches the space in the Table

Board.

3. Place the other two Legs (4) on the Table Board (2) corner nearest the Handle (3), and place one on the diagonal corner located on the outside of the Table Board as in the

Assembly diagram. Make certain that the end with the screw holes is facing upward.

Using a rubber mallet, tap the Legs (4) down into the Table Board.

4. Insert Screws (7) down through the Table Board (2) and into each Leg (4) - see

Assembly diagram.

5. Locate the second Table Board (2) and turn it upside down. Set the second Table

Board onto the Legs (4) making certain that both Table Boards are facing the same way.

6. Turn the Service Cart right-side up. Set the Covers (1) down onto each corner of the top Table Board (2) - see Assembly diagram.

SKU 62703 For technical questions please call 1-888-866-5797. Page 3

Swivel Caster (5)

Table Board (2)

Figure 1

7. Turn the Service Cart upside down again. Attach the Swivel Casters (5) using eight

Bolts (10) and secured in place with Split Washers (9) and Nuts (8).

8. Attach the two Fixed Casters (6) with eight Bolts (10), Split Washers (9) and Nuts (8).

9. Turn the Service Cart upright. Make certain that all hardware is tight. Make certain that the Fixed Casters (6) and Swivel Casters (5) roll properly.

SKU 62703 For technical questions please call 1-888-866-5797. Page 4

Record Product’s Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.

SKU 62703 For technical questions please call 1-888-866-5797. Page 5

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM

IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES

ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED

TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS

OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT

ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED

TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF

HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT

OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

SKU 62703 For technical questions please call 1-888-866-5797. Page 6

PARTS LIST and assembly diagram

Part Description Qty.

1 Cover

2 Table Board

3 Handle

4 Leg

5 Swivel Caster

6 Fixed Caster

7 Screw

8 Nut

9 Split Washer

10 Bolt

11 Rod

1

4

4

2

2

2

16

16

16

16

1 3

2

11

7

9

5

8

6

4

10

1

Note: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts.

SKU 62703 For technical questions please call 1-888-866-5797. Page 7

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF

MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797