PAX TECHNOLOGY INC.
Stylus pen
Touch screen and
Contactless reader area
Magnetic stripe reader
Privacy shield
Keypad
Smart card reader
Cable retention
cover plate
Communication ports - located under cover plate
Speakers
Regulatory label
Part number/ serial number label
Communication module
MAC address label
PAX TECHNOLOGY INC.
P x terminals standard with that one include a
Ethernet default communication module come port and RS
232,
USB
, and PUSB network capabilities . However , if the default communication module your is replaced with an choice of these optional additional communication network capabilities module , are available :
• A second Et hernet port
• Po we r over Et hernet
• An Et hernet hub
• Wi -Fi and Bl uetooth LE
• Wi -Fi and Ce llular GS M
The commu nication mo dule is located on the underside of the termi nal.
Communication ports are labeled and color-coded:
Communication module
White Red Yellow Black Blue Green
WARNING:
Power down and remove all power from the terminal before removing or installing a communication module. A communication module must be installed before power can be applied to the terminal.
3
Power can be supplied via the power port or a single data cable that carries power. This power can be provided via a “powered cable” where the connected POS terminal provides the power
(i.e. PUSB or Power over Ethernet) or by connecting a P power supply directly to the data cable (i.e. RS232 or USB).
1) Power Port
Insert the power connector into the green POWER port. Turn the power connector, locking the tab behind the short plastic wall. Dress the cable through the retention clips. A separate data cable is also required.
2) POS Cable
Insert the cable connector into the appropriate port on the terminal. Dress the cable through the retention clips opposite the port. Connect power supply to cable as required. The cash register could also supply power to terminal.
3) Power over Ethernet (PoE)
Power is available over the red LAN1 port when the optional
PoE communication module is installed.
Cable Retention Cover Plate
After power and data cables are connected and dressed through retention clips, install the cable retention cover plate and secure with captive screw.
Screw
Working Environment: Temperature -10 ° C ～ 50 ° C (14 ° F ～ 122 ° F)
R .
H .: 10% ～ 93% (non-condensing)
Storage Environment: Temperature 20 ° C ～ 60 ° C (-4 ° F ～ 140 °
R .
H .: 5% ～ 95% ( non-condensing)
F )
PAX TECHNOLOGY INC.
4
1)
Mo unting
Locations
2) Stylus Port
3 )
Re tention
Cl ips
1) Align stylus holder over metal screw openings at left side or top of terminal. Insert tabs into indentations along edge. Attach with captive screws.
2) Insert connector end of stylus pen into stylus port on left side of terminal.
3) Use enclosed plastic card to press stylus cord into retention clips on left side of terminal.
5
Insert tabs and snap shield firmly in place to left and right of keypad. Not designed to be removable. Removing the shield breaks the retention tabs and the ability to remotely track the status of the shield is lost.
Decorative Plug – If a privacy shield is not installed, a non-removable decorative plug may be installed in its place. This plug does not provide any PIN entry privacy.
1 Privacy Shield
CAUTION :
If the privacy shield is not installed, you must use PCI-approved alternative methods to secure the PIN pad.
Decorative Plug
6
1) Stylus Holder Plug
If required, to prevent stylus pen from being inserted vertically into stylus holder, firmly insert plug into opening in holder, aligning with curve of stylus holder.
1) Stylus
Holder
Plug
2) Smart Card Reader Plug
If required, insert smart card reader plug into smart card receptacle slot.
To remove, if required, gently pry out the plug using a small screwdriver in the slit along top of plug.
3) Ethernet Plug
An Ethernet plug is included in case
2) Smart Card Reader Plug you want to block an inactive LAN port.
Align plug so that it matches the shape of the port and gently push into opening.
To remove, if required, gently pry off using a small screwdriver in the slit along the top of the plug.
Note: LAN2 port is enabled only when
Ethernet hub or PoE and Ethernet hub communication module is installed.
3) Ethernet
Plug
PAX TECHNOLOGY INC.
7
If required, restart the terminal by pressing in and holding the reset button for 2-3 seconds
Reset
Button
Audio Jack
Stylus Port
If required, a visually disabled person can connect a headphone to the terminal for audio prompting using the
3.5mm output audio jack.
8
If required, insert customer-provided cable lock into K-Slot®. Loop cable around permanent object to secure in place.
9
If required, the P x terminal may be mounted to a stand .
Instructions may vary depending on stand specifications .
Carefully route the required cables up through the stand pipe and out the top. Connect the cables to the
Route
Cables
Insert the three mounting slots on the underside of the terminal into the three metal prongs on the stand base.
Slide the terminal firmly into position, locking the terminal in place on the stand. Secure with fastening screw or locking device as required.
Mounting
Slots
P/N:200312000000224
This docume nt is provided to you for informa tional purposes only. All features and specifications are subject to change without notice. PAX's name and PAX's logo are registered tradema rks of PAX Technology Inc. All rights reserved.
PAX Technology Inc.
4901 Belfort Road, Suite 130
Jacksonville, FL 32256, US A
T: 877-859-0099
W: ww w.pax.us
E: sales@p ax.us
PAX TECHNOLOGY INC.
10
WARNING:
Do not use industrial strength or abrasive cleaner as it may damage or scratch the screen.
Do not immerse device in water (or liquid.)
Do not spray water or cleaner into the MSR slot, Smart Card
Reader or ports.
To clean screen, apply distilled water or mild glass cleaner onto a soft, lint-free cloth and gently wipe terminal screen.
To clean terminal, apply distilled water or plastic-safe cleaner onto a soft, lint-free cloth and gently wipe terminal.
11
RS232 Cable
200204020000140
Requires Power Supply
9
USB Cable
200204020000141
Requires Power Supply
Power Supply
200310110000070
Requires Power Cord
Power Cord
200311020000023
Requires Power Supply
Stylus Pen
200209090000929
Stylus Holder Plug
200209090000930
Privacy Shield
200209060000040
10
Decorative Privacy
Shield Plug
2002090900001037
FCC Regulations:
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications . However , there is no particular guarantee installation that
If interference will this equipment does not occur cause in a harmful interference to determined by radio or television turning the reception
, which can be equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-
Reorient or relocate the receiving antenna
.
Increase the separation between the equipment and receiver .
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-
Consult the dealer technician for help or
.
an experienced radio
/
TV
11
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user ' s authority to operate the equipment.
RF Exposure Information
This device meets the government
' s requirements for exposure to radio waves.This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the
Federal Communications Commission of the U.S.
Government.
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches ) during normal operation .
12
5
PAX TECHNOLOGY INC.
