STOPPING
To stop the motor, simply depress the stop switch until the motor comes to a complete stop. Fig 13
Stop
Switch
ADJUSTING TRIMMING
LINE LENGTH
Your trimmer is equipped with a Bump Feed Cutting
Head that allows the operator to release more trimming line without stopping the motor.
To release additional line, lightly tap the trimming head on the ground while operating the trimmer at high speed. Fig 14
If excess line is released, a blade in the guard will automatically cut the line to the proper length. Fig 15
NOTE: Always keep the trimming line fully extended. Line release becomes more difficult as cutting line becomes shorter.
Fig 13
Fig 14
Fig 15
Blade
CAUTION: Do not remove or alter the line cutting blade on the guard. Excessive line length will cause clutch to overheat and may result in serious personal injury.
REPLACING
EXHAUSTED CUT-
TING LINE
Remove bump head knob by turning anticlockwise. Remove spool and spring from spindle. Fig 16.
Cut 2 x 2.2m lengths of cutting line and insert one end of each line into the two spool holes as illustrated in Fig 17.
Fig 16
Fig 17
Install the spring over the spindle. Insert each end of the cutting line through the eyelets in the cutting head assembly and lower the spool while feeding the line as illustrated in Fig 20.
Once the spool is in place, apply pressure on the spool compressing the spring.
Pull each end of the line sharply to unlock the line from the slots. Continue to apply pressure to the spool until the knob can be threaded clockwise onto the spindle. Tighten the knob securely. Fig 21.
Fig 20
Fig 21
QUICK FIT SYSTEM
Your Ryobi trimmer is equipped with a Quick Fit
System, which enables optional attachments to be connected to your trimmer.
Ask your Ryobi retailer for a list of available optional attachments.
To replace the cutting head with an optional attachment, loosen the knob anticlockwise. Fig 22
Depress the release button and remove the cutting head shaft. Fig 23
Depress release button, and insert shaft of optional add on attachment. Fig 24
When the shaft clicks into place, tighten the knob.
Fig 22
Release Button
Fig 24
Fig 23
AIR FILTER It is recommended that the air filter is cleaned on a regular basis.To clean the air filter, depress the air filter cover latch and remove the cover. Fig 25.
Remove and wash the filter with soap and water.
Allow to completely air dry before replacing the filter.
After replacing the filter secure the air filter cover.
Fig 25
Wind cutting lines clockwise as illustrated in
Fig 18, with each line separated by the spool divider.
Wind to within
15 cm of the end of the line.
Lock each end of the cutting line into the slots on opposite sides of the spool as illustrated in
Fig 19
Spool
Divider
Fig 19
Slots
Fig 18
STORAGE
1.
2.
tor.
If the trimmer will be stored for an extended period of time, use the following storage procedure:
Drain all fuel from the fuel tank into a container.
Start the motor and allow it to run until it stalls. This ensures that all the fuel has been drained from the carbure-
3.
Allow the motor to cool. Remove the spark plug and put approximately 30ml of any high quality oil or 2 stroke oil into the cylinder. Pull the starter rope slowly to distribute the oil. Reinstall the spark plug. Leave the spark plug wire off for storage.
4.
Inspect for any damaged or loose parts. Repair or replace any damaged parts and tighten loose screws, nuts or bolts.
Page 5
RYOBI TECHNOLOGIES AUSTRALIA PTY. LTD.
GUARANTEE
Subject to the guarantee condition below, this Ryobi tool
(hereinafter called “the product”) is guaranteed by Ryobi
(hereinafter called “the Company”) to be free from defects in material or workmanship for a period of 12 months from the date of original purchase covering both parts and labour. Under the terms of this guarantee, the repair or replacement of any part shall be the opinion of the Company or its authorised agent. Should service become necessary during the guarantee period, the owner should contact the Authorised Ryobi Retailer from whom the Product was purchased, or the nearest
Company Branch Office. In order to obtain guarantee service, the owner must present the sales docket and
Guarantee Certificate to confirm date of purchase. This product is sold by the dealer or agent as principal and the dealer has no authority from the Company to give any additional guarantee on the Company’s behalf except as herein contained or herein referred to.
Guarantee Conditions
This guarantee only applies provided that the Product has been used in accordance with the manufacturer’s recommendations under normal use and reasonable care (in the opinion of the Company) and such guarantee does not cover damage, malfunction or failure resulting from misuse, neglect, abuse, or used for a purpose for which it was not-designed or is not suited; and no repairs, alterations or modifications have been attempted by other than an Authorised Service Agent. This guarantee will not apply if the tool is damaged by accident or if repairs arise from normal wear and tear.
The Company accepts no additional liability pursuant to this guarantee for the costs of travelling or transportation of the Product or parts to and from the service dealer or agent - which costs are not included in this guarantee.
Certain legislation, including the Trade Practices Act,
1974 (as amended) and other state and territorial laws give rights to the buyer and impose liability on the seller in certain circumstances. Nothing herein shall have the effect of excluding, restricting or modifying any condition, guarantee, right or liability imposed, to the extent only that such exclusion, restriction or modification would render any term herein void.
RYOBI TECHNOLOGIES AUSTRALIA PTY. LTD.
A.C.N. 002 277 509 Incorporated in N.S.W.
SYDNEY: 359-361 Horsley Road, Milperra, N.S.W.
2214, Phone: (02) 9772 2444 email: [email protected]
MELBOURNE: 960 Stud Road, Rowville, Vic, 3178,
Phone: (03) 9764 8655
HOBART:
BRISBANE:
All Enquiries Phone: 1300 361 505
All Enquiries Phone: 1300 361 505
PERTH: 33-35 Sorbonne Crescent, Canning Vale,
WA, 6155, Phone: (08) 9455 7775
ADELAIDE: All Enquiries Phone: 1300 361 505
TOWNSVILLE: All Enquiries Phone: 1300 361 505
RYOBI TECHNOLOGIES NEW ZEALAND LIMITED
Auckland: 503 Mt Wellington Highway,
Mt Wellington, NZ, Phone: (09) 573 0230 email: [email protected]
THIS GUARANTEE FORM
SHOULD BE RETAINED BY THE CUSTOMER AT ALL TIMES
For your record and to assist in establishing date of purchase (necessary for in-guarantee service) please keep your purchase docket and this form completed with the following particulars.
PURCHASED FROM _______________________________________________________
ADDRESS OF DEALER _____________________________________________________
DATE _________________MODEL NO ___________SERIAL NO ___________________
Present This Form With Your Purchase Docket When Guarantee Service Is Required
OWNER’S OPERATING MANUAL
TRIMMERS
RLT2500QF
RYT2500QF
RST2500QF
SPECIFICATION
Motor
Ignition
Carburetor
Cutting Head
Cutting Line
Width Of Cut
Steel Blade
Weight
RLT2500QF RYT2500QF
25cc 2 Stroke 25cc 2 Stroke
Electronic
Diaphragm, all position
Twin line bump feed
2.5 mm
43 cm
4.9 kg
Electronic
Diaphragm, all position
Twin line bump feed
2.5 mm
46 cm
5.3 kg
RST2500QF
25cc 2 Stroke
Electronic
Diaphragm, all position
Twin line bump feed
2.5 mm
46 cm
Yes
6.0 kg
THANK YOU FOR BUYING A RYOBI TRIMMER.
Your new Trimmer has been engineered and manufactured to Ryobi's high standard for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble free performance.
CAUTION: Carefully read through this entire owner's manual before using your new Trimmer.
Pay close attention to the Rules for Safe Operation, Warnings and Cautions. If you use your Trimmer properly and only for what it is intended, you will enjoy years of safe, reliable service.
Thank You again for buying Ryobi tools.
RULES FOR SAFE OPERATION
The purpose of safety rules is to attract your attention to possible dangers. The safety symbols and the explanations with them, require your careful attention and understanding.
The safety warnings do not by themselves eliminate any danger. The instruction or warnings they give are not substitutes for proper accident prevention measures.
SAFETY ALERT SYMBOL.
Indicates caution or warning. May be used in conjunction with other symbols or pictures.
WARNING: Failure to obey a safety warning can result in serious injury to yourself or to others.
Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
WARNING: Do not attempt to operate this tool until you have read thoroughly and understood completely, safety rules, etc. contained in this manual. Failure to comply can result in accidents involving fire, electric shock or serious personal injury. Save owners manual and review frequently for continuing safe operation and instructing others who may use this tool.
The operation of any tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend Wide
Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields.
10. ALWAYS WEAR SAFETY GLASSES.
Everyday eyeglasses have only impact resistant lenses, they are not safety glasses.
11. PROTECT YOUR LUNGS.
Wear a dust mask if operation is dusty.
12. PROTECT YOUR HEARING.
Wear hearing protection during extended periods of operation.
13. DON'T OVERREACH.
Keep proper footing and balance at all times. Do not use tool on a ladder or unstable support. Secure tools when working at elevated levels.
14. MAINTAIN TOOLS WITH CARE.
Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories.
15. REMOVE ADJUSTING KEYS AND WRENCHES.
Form a habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on.
16. NEVER USE IN AN EXPLOSIVE ATMOSPHERE.
Normal sparking of the motor could ignite fumes.
17. KEEP HANDLES DRY, CLEAN AND FREE FROM OIL
AND GREASE.
Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum based products, or any strong solvents to clean your tool.
18. STAY ALERT AND EXERCISE CONTROL.
Watch what you are doing and use common sense. Do not operate tool when you are tired. Do not rush.
19. CHECK DAMAGED PARTS.
Before further use of the tool, a guard or any other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or any other part that is damaged should be properly repaired or replaced by an authorised service centre.
20. DO NOT USE TOOL IF SWITCH DOES NOT TURN IT
ON AND OFF.
Have defective switches replaced by authorised service centre.
21. DO NOT OPERATE THIS TOOL WHILE UNDER THE
INFLUENCE OF DRUGS, ALCOHOL OR ANY
MEDICATION.
1. KNOW YOUR POWER TOOL.
Read owners manual carefully. Learn its applications and limitations as well as the specific potential hazards related to this tool.
2. GUARD AGAINST ELECTRICAL SHOCK BY
PREVENTING BODY CONTACT WITH GROUNDED
SURFACES.
For example, pipes, radiators, ranges, refrigerator enclosures.
3. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite accidents.
4. AVOID DANGEROUS ENVIRONMENT.
Don't use power tools in damp or wet locations or expose to rain.
Keep work area well lit.
5. KEEP CHILDREN AND VISITORS AWAY.
Visitors should wear safety glasses and be kept a safe distance from work area. Do not let visitors contact tool or extension cord.
6. STORE IDLE TOOLS.
When not in use, tools should be stored in a dry and high or locked-up place, out of reach of children.
7. DON'T FORCE TOOL.
It will do the job better and safer at the rate at which it was designed.
8. USE RIGHT TOOL.
Don't force small tool or attachment to do the job of a heavy duty tool. Don't use tool for purpose not intended.
9. DRESS PROPERLY.
Do not wear loose clothing or jewellery. They can be caught in moving parts. Rubber gloves and non-skid footwear are recommended when working outdoors. Also wear protective hair covering to contain long hair.
SAVE THESE INSTRUCTIONS
FOR FUTURE REFERENCE
Due to Ryobi's continued product refinement policy, product features and specifications can and will change without notice. Check current features and specifications with your Ryobi retailer.
Page 2
Starter
Rope
Primer
Bulb
Choke
Lever
RLT2500QF RYT2500QF RST2500QF n ASSEMBLY
HANDLE Fig 1.
Insert the handle over the shaft and the handle clamp under the shaft. Align the 2 holes in the handle to the holes in the handle clamp.
Secure with 2 bolts, washers, lock washers and tighten gently.
Adjust the handle to the desired height and tighten securely.
Fig 1
Handle
Clamp
GUARD
Model RLT2500QF Fig 2.
Push the guard onto the shaft clamp assembly. Align the 2 holes in the guard with the 2 recesses in the clamp assembly.
Secure with bolt washer, lock washer and wing nut supplied.
Fig 2
Guard
Twin
Cutting
Line
Throttle
Trigger
Stop
Switch
Handle
Split Boom
Handle
Throttle
Trigger
Stop
Switch
Handle
Split Boom
Guard
Throttle
Trigger
Stop
Switch
Guard
Steel Blade
GUARD
Model RYT2500QF &
RST2500QF Fig 3.
Insert the guard recess into the clamp assembly.
Fig 3
Clamp
Assembly
Guard
Recess
Align the hole in the clamp assembly with the hole in the guard and secure tightly with the bolt supplied.
Fig 4
Fig 4
WARNING: To avoid serious personal injury, never operate the trimmer without the guard securely in place.
Page 3
METAL BLADE
Model RST2500QF
Your Ryobi Model
RST2500QF is supplied with a heavy duty metal blade for slashing long scrub and thick undergrowth. To attach the metal
Locking
Rod Slot
Gear Collar blade, insert the gear collar over the spindle shaft and Fig 5 Spindle Cover align the recess in the gear collar with the recess in the spindle cover. Fig 5
Insert the metal blade, flange and hex nut and hand tighten anticlockwise.
Fig 6
Fig 6
STARTING follow these 3 easy steps
1
Place the choke lever in the Cold Start position. Fig 9
1
2
Fully depress and release the primer bulb
5 to 7 times. Fuel should be visible in the bulb. Fig 10
2
Choke
Lever
Fig 9
Fig 10
Primer Bulb
To prevent the shaft from rotating while tightening the hex nut, insert a metal rod or screwdriver into the
Locking Rod Slot and tighten the hex nut securely using a wrench. Fig 7
Fig 7
Fig 8
3
With the trimmer on firm ground, depress the
Safety Switch
3 safety switch and squeeze the throttle trigger fully.
Release the safety switch while retaining full throttle on the trigger and pull the starter rope briskly until the motor sounds like it wants to start. Fig 11 & 12
Throttle Trigger
Fig 11
On release of the throttle trigger, the choke will return to the warm start position. Pull the starter rope 1 to 3 times to start the motor.
Fig 12
OIL & FUEL MIXTURE
Thoroughly mix 200 ml of
2 stroke oil with 5 litres of fresh unleaded fuel in a container and fill the trimmer fuel tank. Fig 8
Care should be taken not to overfill the fuel tank which will result in fuel splashing onto engine parts.
Starter Rope
Fuel Tank
WARNING: Always stop the motor and allow it to cool before re-filling the fuel tank. Failure to adhere to this warning can result in vapour explosion causing serious personal injury.
WARNING: Always mix petrol and oil in a separate container. Do not mix directly in the trimmer fuel tank which will cause motor damage and void the warranty.
Choke Lever in Cold Start Position
NOTE: If the motor floods while attempting to start the trimmer, ensure the choke lever is in the warm start position, depress the safety switch and squeeze the throttle trigger. Release the safety switch and pull the starter rope briskly. The motor should start within 3 to 8 pulls.
NOTE: Choking is not required when starting a warm motor. Start a warm motor in the warm start position.
Page 4
