80140502-001
User Manual
Spectrum Pro
PCI PTS 4.X Hybrid Insert Reader
USB / RS232 Interface
80140502-001
Rev. A 5/17/2017
International Technologies & Systems Corporation
10721 Walker Street, Cypress, CA 90630-4720; Tel: (714) 761-6368; Fax: (714) 761-8880 www.idtechproducts.com
Spectrum Pro User Manual
Copyright © 2017 ID TECH. All rights reserved.
ID TECH
10721 Walker St.
Cypress, CA 90630 [email protected] Visit: http://www.idtechproducts.com
This document, as well as the software and hardware described in it, is furnished under license and may be used or copied online in accordance with the terms of such license.
The content of this document is furnished for information use only, is subject to change without notice, and should not be construed as a commitment by ID TECH. While every effort has been made to ensure the accuracy of the information provided, ID TECH assumes no responsibility or liability for any unintentional errors or inaccuracies that may appear in this document.
Except as permitted by such license, no part of this publication may be reproduced or transmitted by electronic, mechanical, recording, or otherwise, or translated into any language form without the express written consent of ID TECH.
ID TECH and ViVOpay are trademarks or registered trademarks of ID TECH.
Warranty Disclaimer: The services and hardware are provided "as is" and "as-available" and the use of the services and hardware is at its own risk. ID TECH does not make, and hereby disclaims, any and all other express or implied warranties, including, but not limited to, warranties of merchantability, fitness for a particular purpose, title, and any warranties arising from a course of dealing, usage, or trade practice. ID TECH does not warrant that the services or hardware will be uninterrupted, error-free, or completely secure.
Copyright © 2017, International Technologies & Systems Corp. All rights reserved.
Page 2 of 15
Spectrum Pro User Manual
Revision History
Revision Date
50 2/23/2015
Description of Changes
Preliminary Version
51 3/10/2015 Revise low power mode
52
A
10/27/2015 Expanded description of Features and Benefits
Default sleep timeout value is 120 seconds
5/17/2017 Update status LED table, add low-power mode details, correct various items.
By
CH
CH
KT
KT
Copyright © 2017, International Technologies & Systems Corp. All rights reserved.
Page 3 of 15
Spectrum Pro User Manual
Table of Contents
1.
INTRODUCTION .............................................................................................................................. 5
2.
FEATURES AND BENEFITS ................................................................................................................ 5
3.
ABBREVIATIONS.............................................................................................................................. 5
4.
APPLICABLE DOCUMENTS ............................................................................................................... 6
5.
FRONT AND BACK VIEW .................................................................................................................. 6
6.
SPECIFICATIONS .............................................................................................................................. 7
6.1
S UPPLY POWER
................................................................................................................................. 7
6.2
R ELIABILITY AND E NVIRONMENT
..................................................................................................... 8
6.3
E NVELOPE D RAWING
........................................................................................................................ 9
6.4.1
RS232 C OMMUNICATION S ETTINGS
........................................................................................... 10
7.
MOUNTING INSTRUCTIONS .......................................................................................................... 11
8.
LED MANAGEMENT ...................................................................................................................... 12
8.1
F RONT LED S TATUS
....................................................................................................................... 12
8.2
D IAGNOSTIC LED S TATUS
.............................................................................................................. 12
9.
OPERATION PROCEDURE .............................................................................................................. 15
Copyright © 2017, International Technologies & Systems Corp. All rights reserved.
Page 4 of 15
Spectrum Pro User Manual
1.
Introduction
Spectrum Pro is a PCI PTS 4.X and SRED certified outdoor hybrid insert reader which can read both magstripe cards and chip cards. Meeting the latest requirements of the payment industry, the Spectrum Pro is EMV Level 1 and Level 2 approved, and features
DUKPT key management with Triple DES (TDES) encryption to ensure MagStripe and
Smart card data will always be protected.
The Spectrum Pro integrates directly with ID TECH’s SmartPIN L100 keypad for a complete Chip & PIN solution.
Integrators and application developers can create apps that communicate with Spectrum
Pro using ID Tech's Universal SDK, which provides a comprehensive Windows-based development environment for programmatic control of the unit. Developers can also communicate with Spectrum Pro directly using UART and/or USB-HID. For details, see the P/N 80140505-001 Spectrum Pro Low Level API Manual . This manual contains the complete firmware-level API guide for controlling Spectrum Pro directly. The low-level
API manual can be downloaded from: https://atlassian.idtechproducts.com/confluence/display/KB/Spectrum+Pro+-+downloads
2.
Features and Benefits
EMV Level 1 and Level 2 certified
PCI 4.X certification with SRED support
PBOC level 1 and 2
Supports TDES encryption with DUKPT key management
Reads up to 3 tracks of card data
Two SAM modules
Front switch, card seated switch, and latch
IP 65 rating and IK 10
Low power sleep mode and stop mode
3.
Abbreviations
AAMVA
DES
MSR
TDES
PCI
POS
American Association of Motor Vehicle Administrators
Data Encryption Standard
Magnetic Swipe Reader
Triple Data Encryption Standard
Payment Card Industry
Point of Sale
USB
PCI
Universal Serial Bus
Payment Card Industry
SRED Secure Reading and Exchange of Data
EMV Europay, MasterCard, and Visa
Copyright © 2017, International Technologies & Systems Corp. All rights reserved.
Page 5 of 15
Spectrum Pro User Manual
4.
Applicable Documents
ISO/IEC 7813 – Identification cards, Physical Characteristic
ISO/IEC 7811 – Identification cards, Recording Techniques, Magnetic Stripe
80140505-001 – ID Tech Spectrum Pro Low Level API Manual
5.
Front and Back View
Copyright © 2017, International Technologies & Systems Corp. All rights reserved.
Page 6 of 15
Spectrum Pro User Manual
6.
Specifications
6.1
Supply power
Supply voltage:
DC 5V without supporting latch
Additional DC 12V to support latch if latch is needed
Operating current o Idle – 100mA o Max – 120mA
USB suspend current: 200 uA
Sleep mode current: 20 uA
Stop mode current:
with UART wakeup, 16 uA
with no UART wakeup, 10 uA
Reader falls into sleep mode after it is idle for specified time duration. The default time duration is 120 seconds. (This can be adjusted, or even disabled.)
Reader can be commanded to go to Stop mode (which is a special very-low-power consumption mode).
Reader can wake up from Sleep mode by card insertion or via UART command.
Response time: < 100 ms.
Reader can wake up from Stop mode by card insertion.
Power-Off to Power-On time: < 500 ms
Copyright © 2017, International Technologies & Systems Corp. All rights reserved.
Page 7 of 15
Spectrum Pro User Manual
6.2
Reliability and Environment
Reliability
Magnetic Head Life: 1,000,000 passes minimum
Rail and Cover Life: 1,000,000 passes minimum
Environmental Temperature range:
Operating:
-13º F to 158º F ( -25º C to 70º C) non-condensing
Storage:
-40º F to 176º F ( -40º C to 80º C) non-condensing
Relative humidity
10% to 95% non-condensing
ESD
- 6kV contact, and 12 kV air discharge, per ID TECH ESD testing procedure, without permanent damage
Copyright © 2017, International Technologies & Systems Corp. All rights reserved.
Page 8 of 15
Spectrum Pro User Manual
6.3
Envelope Drawing
Copyright © 2017, International Technologies & Systems Corp. All rights reserved.
Page 9 of 15
Spectrum Pro User Manual
6.4.1
RS232 Communication Settings
Parameter
Specification
Transmission protocol Asynchronous
Communication method Full Duplex
Start bit l bit
Data length 8 bits (Bit7: MSB, Bit0: LSB)
Parity
Stop bit
None l bit
Transmission speed
(Baud rate)
115200 bps (default)
Copyright © 2017, International Technologies & Systems Corp. All rights reserved.
Page 10 of 15
Spectrum Pro User Manual
7.
Mounting Instructions
The reader can be mounted in either a horizontal or vertical orientation. The removal detection points must be pressed down when the unit is mounted. Please refer to the mounting drawing below.
Copyright © 2017, International Technologies & Systems Corp. All rights reserved.
Page 11 of 15
Spectrum Pro User Manual
8.
LED Management
There are two LEDs. One is the user-interface LED on the front bezel of the reader; the other (diagnostic) LED is on the back.
8.1
Front LED Status
The LED turns green in idle waiting.
LED handling for Magstripe card operation:
The LED will turn red to indicate that the recent magstripe card read was bad.
LED handling for smart card operation:
The Green LED will flash after powering on the smart card.
The solid Green LED indicates smart card processing is complete and the ICC powered off. The user can remove the smart card.
State LED Indicating
0
1
2
3
Off
Flashing
Green
Solid
Green
No external power
Powering on the smart card and starting smart card operation
Idle waiting (Smart card processing is complete and the ICC powered off. User can remove the smart card. If the transaction mode was
MSR, magstripe card data is sent out.)
Solid Red The recent magstripe card read was bad. Red lasts 1 second.
8.2
Diagnostic LED Status
The LED on the back of Spectrum Pro can be used for diagnostic purposes.
LED status:
1.
Off
2.
Solid – No communication with its host.
3.
Flashing (1 sec on, 1 sec off) – Communicating with its host.
LED Colors:
Amber – Reader requires on-site service actions.
Green – Reader is ready to read cards.
Red – Reader needs to be sent back to the manufacturer.
Copyright © 2017, International Technologies & Systems Corp. All rights reserved.
Page 12 of 15
Spectrum Pro User Manual
LED
State
1
2
3
4
Green
Off
Solid
Green
Amber
Off
Solid
Amber
Solid
Amber
Red
Off
Solid
Red
Indicating Service action
Check the power cable and power supply No external power
Power is on, but firmware(either K21 or MaxQ) doesn't run
Solid amber normally means the front removal-detection buttons (left side of front bezel) are not depressed.
If this possibility is ruled out, check host connectivity.
Dismount the device and send it back to the manufacture.
Check that the removal detection button is fully depressed. Check the communication cable and if host is running.
Power on. First restart and no command sent. In not ready state, and waiting for host to communicate.
RFU
5
RFU RFU RFU RFU
Off
6
Flashing
Green
Flashing
Amber
7
Solid
Green
8
Flashing
Green Off
Firmware downloading and programming
In ready state but no communication with its host
Command sent to reader; reader waiting for response.
RFU
RFU
RFU
Copyright © 2017, International Technologies & Systems Corp. All rights reserved.
Page 13 of 15
10
11
9
Spectrum Pro User Manual
Flashing
Amber
Removal flag on and communicating with its host
Check removal switch if they are fully engaged and call service center to reactivate the reader.
Solid
Amber
Solid
Red
Reader has no communication with its host, and the crypto driver is not functioning:
Crypto MCU is lost or certificates are invalid (may be tampered)
Dismount the reader and send it back to its manufactory
Flashing
Amber
Reader is communicating with its host, and the crypto driver is not functioning: Crypto
MCU is lost or certificates are invalid (may be tampered)
Dismount the reader and send it back to the manufacturer
Copyright © 2017, International Technologies & Systems Corp. All rights reserved.
Page 14 of 15
Spectrum Pro User Manual
9.
Operation Procedure
A chip card should be inserted with chip side facing up (as shown below). A magstripe card should be inserted with magstripe facing down and to the right side of the reader.
Please see pictures below.
Copyright © 2017, International Technologies & Systems Corp. All rights reserved.
Page 15 of 15
