VIEW SIZE THE WORLD
Driver 4–
NOTE
Quick Start
For full installation, configuration, and operation details, please refer to the Driver 4 user manual, which is available at www.rgblink.com.
This guide provides quick start instructions for an experienced installer
to set up and operate the Driver 4.
Installation and cabling features
Rear Panel
Connections
1 Audio Input Interface
2 DVI Input Interface
3 HDMI Input Interface
Step 2-Audio Input
Connect to microphone or the device with audio interface.
Step 3-DVI Input
Use to input DVI from DVI player or computer with DVI connector.
Step 4-HDMI Input
Can receive video signal from HD player,
DVD and computer.
Step 5-USB Interface
5
9
10
6 7
Step 6-Gigabit Copper Port
8 Gigabit Copper Port
Switch
Power
4 USB Interface
Step 1-Mounting
Turn off or disconnect all equipment power sources.
Use to cascade the device. Currently, Driver 4 can only cascade 2 pieces, and only available for Colorlight Q7e sending card.
Local Control Front Panel Operation
Function Button
1
2 3
Nixie Tube
Function Button
4
5
USB control Port of
Sending Card
LED Indicator
Nixie Tube
Can control the brightness of LED sending card, and the nixie tube will display the brightness value.
Function Button
Button 2: Down key, can switch to the top level brightness value.
Button 3: Up key, can switch to the next level brightness value.
USB Control Port of Sending Card
User can connect PC via USB cable and control sending card software.
LED Indicator
Red: Power indicator, it lights when device has power supply.
Green: Signal indicator, it lights when device has signal input.
Connect to LED screen through cable.
Operation Manual
Step 7-Power
Plug in power cord which has IEC connector, Driver 4 supports AC power from 85 to 264V, 50-60Hz, which means world wide compatible.
Power On
Connect one end of the power with the device, the other end into a socket, and push power switch to ON position. Red power indicator light means the device works normally.
How to connect
Connect the HD player, DVD or computer to the
HDMI input interface with HDMI cable.
Connect the DVI player or computer with DVI interface to the DVI interface with DVI cable.
Connect the computer to the USB control port of sending card with USB cable.
Connect the receiving card of LED Display to the
Gigabit Copper Port with cable.
Address: S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone, Xiamen, Fujian Province, P.R.C
Tel: 00865925771197 Fax:00865925771202
Email: [email protected] http://www.rgblink.cn
Driver 4 Quick Start
Rev 1.0
Page 1 of 2
Connect the microphone or other devices with audio interface to the audio interface with 3.5mm headphone cable.
Plug in power cord with IEC connector.
How to work
Push power button to ON position, the red indicator is on if the device is in normal operation.
When input DVI and HDMI signal simultaneously, the
HDMI signal has priority, green signal indicator lights, and the device output HDMI signal. Pull out the HDMI cable, green signal indicator lights, and then the device output DVI signal.
How to cascade the device
1. First, make sure the device is in normal operation.
2. Connect any USB interface in back panel to any USB
interface in back panel of the second piece of Driver 4
with USB cable.
3. Connect the other USB interface in back panel to the
other USB interface in back panel of the second piece
of Driver 4 with USB cable.
4. Cascade the device is finished.
Currently, Driver 4 can only cascade 2 pieces,
and only available for Colorlight Q7e sending
card.
How to control the brightness of sending card
1. First, make sure the device is in normal operation.
2. Choose the brightness value according to actual need
via UP/DOWN keys, the adjustment value range is
0~16 for Colorlight Q7e sending card and 0~64 for
Nova MSD300 sending card, the higher the
brightness value, the brighter sending card will be.
Common Questions and Solution
Nixie tube can not display brightness value
It usually occurs in Nova sending card. When Nova sending card connected to PC software via USB, the key operation of control brightness is invalid, and nixie tube will not display the brightness value. User can only control the brightness via PC software or pull out the
USB cable to recover the key brightness controlling.
No output on LED display
1. Check whether input the signal.
2. Check whether the cable is connected, and in good
connection.
3. Check whether the input and output cable are normal.
Address: S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone, Xiamen, Fujian Province, P.R.C
Tel: 00865925771197 Fax:00865925771202
Email: [email protected] http://www.rgblink.cn
Driver 4 Quick Start
Rev 1.0
Page 2 of 2
