advertisement
INSTALLATION MANUAL
KPF-2120
Single Handle Pull-Down
Kitchen Faucet
www.kraususa.com I toll free: 1.800.775.0703 I © 2013-2014 Kraus USA Inc.
Congratulations on your new Kraus purchase!
We would like to take this opportunity to thank you for your business with Kraus USA.
It is our sincere hope that you are completely satisfied with your Kraus experience.
We welcome any questions or comments you may have, and look forward to assisting you in the future.
For more information about Kraus products, please visit our website at:
www.kraususa.com.
In order to allow us to serve you better, we recommend registering your new Kraus product at: www.kraususa.com/product-registration
Sincerely,
Kraus Customer Service Department
Prior to Installation
•
Make sure that the cold and hot water lines are turned off
•
Wrap all threaded connections with Teflon tape. Always wrap in a clockwise direction
•
Cover your drain to avoid losing parts
•
Do not disassemble the main faucet body, as it has been factory assembled by
Kraus for stress-free installation.
•
Using condition: Working pressure at 0.05-1.0MPa (including cold & hot water pressure) with applicable water temperature: 40C-900C
•
Remove the check valve assembly (30) at the end of the hose (2)
• Remove plastic nut (28) and metal nut (27) from the mounting pipe (32)
•
Discard plastic caps from the hot and cold inlets
KPF-2120 Diagram and Parts List
Tools you will need:
Wrench
(Included)
Phillips
Screwdriver
2
3
1
11
9
10
6
7
25
24
32
26
27
28
30
Spanner
(Included)
Aerator
Key
5
19
SHORT: COLD
LONG: HOT
20
21
22
23
18
17
12
15
16
14
13
31
29
Adjustable
Wrench
Faucet
Extender
4
Included Parts:
1. Spray Head
2. Hose
3. Plastic Cover
4. O-Ring
5. Spout
6. O-Ring
7. Sleeve
8. O-Ring
9. Sleeve
10. Sleeve
11. Set Screw
12. Handle
13. Index Button
14. Set Screw
15. Cartridge Holder
16. Locking Nut
17. Cartridge
18. Faucet Body
19. Plastic Base Ring
20. O-Ring
21. Faucet Extender
22. Rubber U-Washer
23. Metal U-Washer
24. Weight
25. Screws (2)
26. Metal O-Ring
27. Metal Nut
28. Plastic Nut
29. Hot & Cold Waterlines
30. Check Valve Assembly
31. Supply Pipe
32. Mounting Pipe
Dimension Drawings
245 mm
(9.64”)
45˚
45˚ Ø 31mm
(1.22”)
415 mm (16.33”)
Ø 62 mm
(2.44”)
160 mm
(6.3”)
190 mm (7.48”)
120 mm (4.72”)
90 mm (3.54”)
Safety Tips
•
If soldering the water connections when installing the faucet, remove the O-rings, cartridges, and washers before applying any heat
•
Protect your eyes with safety glasses when cutting or soldering
M19X1
G1/2
G1/2
Ø 18 mm
(0.7”)
˚
25
205 mm (8.07”)
Dimension Drawings
415 mm (16.33”)
190 mm (7.48”)
245 mm
(9.64”)
45˚
45˚ Ø 31mm
(1.22”)
˚
25
205 mm (8.07”)
120 mm (4.72”)
90 mm (3.54”)
Ø 62 mm
(2.44”)
160 mm
(6.3”)
M19X1
G1/2
G1/2
Ø 18 mm
(0.7”)
Safety Tips
•
Do not overtighten fixing screws/nuts. Tighten finger-tight, then use a wrench/ screwdriver to tighten the fixing screw/nut until snug
Faucet Installation Procedures
Step 1
Insert faucet body (18) on the predrilled hole 1-3/8”
6
6
6
18 18
21
32
22
27
23
26
Step 2
32
21
32
22
27
32
23
26 rubber u-washer (22), and metal u-washer (23) on the mounting pipe (32) until it touches the base of the countertop. Place metal o-ring
(26) and thread metal nut (27) onto the mounting pipe (32)
Spanner
Tool
21
32
32
22
27
23
26
Spanner
Tool
32
28
18
32
Spanner
Tool
31
30
32
28
31
30
2
2
30
31
30
30
2
30
2
24
2
2
24
25
25
2 24
25
24
25
2
24
25
2
24
25
29
29
29
29
2 2
29
29
2
2
1
2
1
1
2
1
12
12
1
1
12
6
21
32
22
27
23
26
18
Step 3
32
28
Tighten the metal nut (27) on the mounting pipe (32) with the provided spanner until snug underneath the countertop
21
32
22
27
23
26
18
Step 4
32
26
27
Spanner
Tool
Place the plastic nut (28) on the mounting pipe (32) and tighten with an adjustable wrench (not included) until snug
Note: The plastic nut only tightens at the end of the mounting pipe (32)
32
28
31
30
32
Spanner
Tool
6
2
31
30
30
2
30
2
24
25
2
24
25
2
24
25
2
24
25
29
29
29
2
29
2
2
1
2
1
1
12
1
12
21
32
22
27
23
26
21
32
22
27
23
26
32
Spanner
Tool
18
18 32
32
Spanner
Tool
28
6
Step 5
Secure the check valve assembly
(30) onto the supply pipe (31).
Tighten with an adjustable wrench until snug
32
28
31
30
Step 6
6
2
30
31
30
30
2
Secure the end of the hose (2) onto the check valve assembly (30) and tighten with an adjustable wrench until snug
Note: Check if O-rings are installed in the check valve assembly (30) before installing hose (2)
2
24
25
2
24
25
2
24
25
29
2
29
24
25
2
29
2
1
29
2
1
12
2
1
1
12
6
18
21
32
22
27
23
26
21
32
22
27
23
26
29
32
Spanner
Tool
32
Spanner
Tool
18
18
21
32
22
27
23
26
32
28
32
Spanner
Tool
32
28
32
28
31
30
6
2
30
31
30
30
31
30 6
2
Install the weight (24) at the lowest
2
Phillips head screwdriver
2
2
24
25
2
24
25
30
2
29
2
Step 8
24
25
2
24
25
24
25
29
2
Connect hot & cold waterlines
(29) to the faucet hot and cold tighten with an adjustable wrench until snug
Note: Check if O-rings are installed on both ends of the hot & cold waterlines (29)
2
1
29
2
1
1
12
1
12
2
2
1
1
12
21
32
22
27
23
26
6
18
32
Spanner
Tool
18
6
32
28
32
28
21
32
22
27
23
26
32
Spanner
Tool
31
30
2
30
31
30
2
24
25
2
24
25
2
30
2
24
25
2
24
29
25
29
Step 9
29
Thread hot & cold waterlines (29) onto the angle stops and tighten with an adjustable wrench until snug
2
Step 10
29
2
Remove spray head (1) and turn the faucet on while holding the tip of the hose (2) to flush any debris 2
1
2
1
1
12
1
12
21
32
22
27
23
26
6
18
32
21
Spanner
Tool 32
22
27
23
26
32
32
22
27
23
26
18
32
Spanner
Tool
18
32
28
6
6
31
30
32
32
28
Spanner
Tool
31
30
2
31
30
2
30
2
30
2
24
2 25
24
25
2
2
24
24
25
25
30
2
24
25
2
24
29
25
29
29
2
29
29
2
29
2
1
2
Step 11
Step 12
2
1
12
2
1
Secure the spray head (1) onto the hose (2) and hand-tighten only
12
1
1
Note: Check if O-ring is visible in the hose (2) prior to reinstalling the spray head (1)
Turn the faucet on and check if the spray head (1) switches modes properly by pressing the button
1
12
Care & Maintenance
*To keep the product clean & shining, follow the steps below:
1.
2.
3.
4.
Rinse with clean water & dry with a soft cloth
Do not clean with soaps, acid, polish, abrasives, or harsh cleaners
Do not use a cloth with a coarse surface
Unscrew the aerator and clean when necessary
*This installation manual is subject to change without further notice.
Trouble - Shooting
If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps:
P R O B L E M C A U S E A C T I O N
Leakage under the handle
Water will not shut off completely
Leaking between spray head and the hose
Locking nut has come loose
Cartridge may need to be adjusted or replaced
Remove the index button on the side of the handle.
Loosen set screw with a hex wrench. Remove handle and unscrew cartridge holder by hand.
Tighten locking nut with an adjustable wrench or shower wrench (if applicable)
Remove the index button on the side of handle. Loosen set screw with a hex wrench.
Remove the handle and unscrew cartridge cover by hand. Unscrew the locking nut with an adjustable wrench or shower wrench (if applicable). Remove ceramic disc cartridge. Check for cracks
Spray head may be loose or washer is not seated correctly in the hose connection
Tighten the spray head by hand until snug. Make sure the washer is seated correctly
Low/No pressure Check valve assembly may be clogged with debris or washers are not seated correctly
Remove check valve assembly and soak it in warm soapy water to remove any debris for 5 minutes. Make sure the washers are seated correctly
Codes/Standards Applicable:
Specified model meets or exceeds the following: ANSI/ASME A112.18.1, cUPC,
AB1953
KRAUS LIMITED LIFETIME WARRANTY
This product has been manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”). We offer our customers thoughtfully crafted fixtures
& accessories, engineered for enduring performance over years of use.
WHO IS COVERED BY THE WARRANTY
This warranty extends to the original purchaser only. This warranty is not transferable, between homes or owners and is only applicable to residential use.
WHAT IS COVERED BY THE WARRANTY
Kraus warranties this product against defects due to material or craftsmanship error during the warranty period: Kraus will provide replacement parts at no charge, or at its option, replace any product or part of the product that is deemed defective, under normal installation, use, service and maintenance. If
Kraus is unable to provide a replacement and repair is not practical or cannot be made in timely fashion, Kraus may elect to refund the purchase price in exchange for the return of the product.
CONDITIONS AND EXCLUSIONS
Like other home fixtures, Kraus products will require light maintenance to ensure proper function. We provide you with complete knowledge to perform this maintenance and can also recommend resources if you are unable to fulfill this service.
A. Kraus will not be responsible for product failures due to lack of maintenance or proper use. Please read your care and maintenance documentation to determine the limits of proper use.
B.
The original sales receipt, order number, and/or proof of purchase must be presented at the time of the warranty claim, without exception, for this warranty to be applied to all Kraus products.
C. Kraus recommends installing all Kraus products with a licensed, professional plumber. Kraus will not be held responsible for any damage or product failure due to improper installation, misuse, or failure to use a licensed professional.
Please read your care and maintenance documentation to determine the limits of proper use.
D.
Commercial use will automatically void this warranty.
E. This warranty is not applicable to Kraus products purchased from an unauthorized seller. For a complete list of authorized sellers please visit http://www.
kraususa.com/where-to-buy.html
NON-APPLICABILITY OF THIS WARRANTY
By the purchase and use of our products, you agree that Kraus is not liable for incidental, consequential or special damages associated with the return, replacement, installation or use of your product. This includes freight costs, cartridge replacement, labor, travel time, lost profit, home damages and other contingent liabilities and costs (including, without limitation, costs associated with experts, investigations, analyses, attorneys and other professionals and services). The Kraus warranty is a comprehensive and explicit limit of liability, and all items outside of it are not addressable by or the responsibility of
Kraus. Certain states have variances regarding implied warranties and in those situations we remain fully compliant.
KRAUS USA Inc. makes no implication that products comply with any or all local building or plumbing codes. It is the consumer’s responsibility to determine local code compliance. This warranty extends to the original purchaser and first consumer.
HELP LINE
For additional assistance at any point in the installation process, please call us at
1.800.775.0703 or email us at [email protected]
Our customer service hours are Monday – Friday, 9am – 8pm EST.
Be sure to visit our website at www.kraususa.com.
www.kraususa.com
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement