JAYPRO PVB SERIES CLASSIC STEEL COLLEGIATE NET SYSTEM
Installation and Operating Instructions
Applicable Part Numbers/Models:
PVB-3000: Classic Steel Collegiate Net system
JSL-Inst042
www.jayprosports.com
PVB Series Classic Steel Collegiate Net System Instructions
Table of Contents
1
Safety................................................................................................................ 2
2
Specifications .................................................................................................. 2
3
Introduction ..................................................................................................... 2
4
Required Tools ................................................................................................. 3
5
Included Hardware & Components ............................................................ 4
5.1 System Components.............................................................................. 4
5.2 Hardware................................................................................................. 5
6
Assembly .......................................................................................................... 6
7
Maintenance .................................................................................................. 9
- 1 of 9JSL-Inst042
www.jayprosports.com
UPDATED 9/25/2018
PVB Series Classic Steel Collegiate Net System Instructions
1
•
•
•
•
•
Safety
WARNING: Do not attempt to remove the height adjuster pin if the net is under
tension.
WARNING: Always use protective padding around each upright during use.
WARNING: Uprights are heavy. Do not attempt to lift or install without assistance.
IMPORTANT: Follow all warning labels on equipment.
IMPORTANT: Inspect for damage before and after each use.
2
Specifications
PVB-3000
3
UPRIGHT
OUTER
DIAMETER
HEIGHT RANGE
POSITIONS
3”
(76mm)
6’6” to 8’2”
(2.0m to 2.5m)
16
Pin Stops
WEIGHT
UPPER
UPRIGHT
MATERIAL
LOWER
UPRIGHT
MATERIAL
157 lbs
(71kg)
Aluminum
6063
Steel
# OF
Introduction
Note: The Flex Net supplied with this system will stretch slightly during the first few uses.
This is a natural consequence of the headband fibers being stretched under tension.
During this break-in period, the headband and net body may sag during use. Simply
increase tension (center if necessary) to remove the sag.
These instructions assume that the appropriate ground sleeves have been correctly
installed:
• The inside bottom surface of the ground sleeves must be 10” below ground level
(Figure 3-1).
•
The standards will fit most 3” inner diameter ground sleeves (or 4” ID sleeves with
adapter).
•
The Flex-Net will work with ground sleeves spaced 35’ to 37’ apart on center1.
Please consult the instructions and specifications supplied with your ground sleeves for
more information.
If you require additional information or support to install or operate your volleyball system,
please contact the Jaypro Sports customer support team, Monday through Friday,
8:30AM to 5:00 PM (EST), at 1-800-243-0533.
NCAA and NFHS rules require that the upright standards must be installed at least 3’3”
(1m) outside the court boundaries. Jaypro recommends 36’ spacing on center to satisfy
both regulations.
1
- 2 of 9JSL-Inst042
www.jayprosports.com
UPDATED 9/25/2018
PVB Series Classic Steel Collegiate Net System Instructions
Figure 3-1: Correct Ground Sleeve Dimensions
4
Required Tools
Before continuing, please verify that you have the following tools required to complete
the installation and setup of your PVB Series Collegiate Net System.
▪ Adjustable wrench
▪ Hex keys – 3/16”, 5/16”
- 3 of 9JSL-Inst042
www.jayprosports.com
UPDATED 9/25/2018
PVB Series Classic Steel Collegiate Net System Instructions
5
Included Hardware & Components
Before continuing, please open all packages to verify that you have all the required
hardware for installation and setup. If any of the following items are missing, contact the
Jaypro Sports customer support team, Monday through Friday, 8:30AM to 5:00 PM (EST),
at 1-800-243-0533.
5.1
System Components
Figure 5-1: PVB-3000 Standard Upright (PVB300B, 2X).
Figure 5-2: Winch with strap (PVBWINCH, 1X).
Figure 5-3: Flex-Net (PVBN-6, 1X)
- 4 of 9JSL-Inst042
www.jayprosports.com
UPDATED 9/25/2018
PVB Series Classic Steel Collegiate Net System Instructions
Figure 5-4: Antennae and Net Tapes (VBA-80, 1 pair)
5.2
Hardware
Figure 5-5: Net extension cord 31 inches (PVBN6R2, 2X)
Figure 5-6: Socket Cap Screw (HS5082, 1X)
Figure 5-8: Centering Strap (PVB604, 1X)
Figure 5-9: Acorn Nut (HN6112, 2X)
Figure 5-10 Spacer (HM6347, 1X)
Figure 5-11: Button Head Screw (HS5240, 1X)
Figure 5-12: Carabiner (HM5054, 2X)
- 5 of 9JSL-Inst042
www.jayprosports.com
UPDATED 9/25/2018
PVB Series Classic Steel Collegiate Net System Instructions
6
Assembly
WARNING: Uprights are heavy. Do not attempt to lift or install without assistance.
1. Install each upright into the ground sleeves.
2. Follow instructions included with winch to set the winch clamp to the correct
upright diameter (3”).
3. Install winch to one upright using the socket cap screw and acorn nut (Figure 6-1,
items 1 & 2).
4. Fasten the clamp together using the cap screws supplied with the winch (Figure
6-1, item 4-1).
Figure 6-1: Winch installation.
- 6 of 9JSL-Inst042
www.jayprosports.com
UPDATED 9/25/2018
PVB Series Classic Steel Collegiate Net System Instructions
5. Install 31 inch net extension cord and the centering strap assembly to the upright
without the winch. (Figure 6-2).
Figure 6-2: Install net extension cord to anchor side.
- 7 of 9JSL-Inst042
www.jayprosports.com
UPDATED 9/25/2018
PVB Series Classic Steel Collegiate Net System Instructions
6. Attach one end of net to 31 inch Extension Cord with the Carabiner
provided, then attach other end of the extension cord to the winch
strap (Figure 6-3).
Figure 6-3
: Attach net to straps.
7. Set the height of the uprights using the installed height adjust pin (Figure 6-4).
***WARNING: Do not attempt to remove the height adjuster pin if the net is under tension.
Figure 6-4: Set upright height.
***The net will stretch ~6 – 8 inches when tension is applied so you must factor this
in before applying tension when centering the net.
- 8 of 9JSL-Inst042
www.jayprosports.com
UPDATED 9/25/2018
PVB Series Classic Steel Collegiate Net System Instructions
8. Tension the net by turning the winch handle clockwise2. Adjust anchor strap as
necessary to keep net centered.
9. Verify net heights and net centering. The uprights will deflect inward and
downward due to net tension; you may need to adjust their heights and/or recenter the net. WARNING: Release tension from the net before removing height
adjust pin.
10. Attach the bottom net straps to each upright as shown in Figure 6-5. Wrap Velcro
straps around buckles for additional player safety.
Figure 6-5 : Secure bottom net straps to uprights.
11. Attach net antennae and tapes according to instructions included with
antennae set.
12. Install pads around each upright.
7
Maintenance
Your PVB Series Classic Steel Collegiate Net System is designed to provide years of play;
however, it is recommended that the components be inspected at least once every
season, for signs of excessive wear. Key areas to inspect include (but are not limited to):
▪ Strap webbing
▪ Net
▪ Spring clips and D-rings
▪ Winch mechanism
▪ Screws and nuts
If you require additional information or support maintaining your volleyball system, please
contact the Jaypro Sports customer support team, Monday through Friday, 8:30AM to
5:00 PM (EST), at 1-800-243-0533.
NCAA and NFHS rules stipulate that there be no more than ¾” of sag in the net
headband when fully tensioned.
2
- 9 of 9JSL-Inst042
www.jayprosports.com
UPDATED 9/25/2018
">
