BandLuxe E504, E538 User Manual

EN-1
P/N: 65012500011 Rev.A
Table of Contents
ABOUT THIS MANUAL ...........................................................................4
PRODUCT OVERVIEW .............................................................. 5
FEATURES.........................................................................................5
PACKAGE CONTENTS ............................................................................5
PARTS AND FUNCTIONS.........................................................................6
MOUNTING AND INSTALLATION ................................................................7
Wall Mounting .................................................................................. 8
Pole Mounting................................................................................... 9
GETTING STARTED ................................................................ 10
INSTALL THE SIM CARD ...................................................................... 10
ASSEMBLE THE OPTIONAL RJ-45 WATER RESISTANT KIT ...................................... 11
GROUNDING THE CPE ........................................................................ 11
CONNECT THE COMPUTERS .................................................................. 12
USING WEB-BASED MANAGEMENT ....................................... 13
LOGIN ........................................................................................... 13
BASIC NETWORK SETTINGS ................................................................. 15
Configure
Configure
Configure
Configure
Mobile Internet Settings .................................................... 15
CPE IP Settings ................................................................ 16
DHCP Services ................................................................. 17
CPE Time......................................................................... 18
STATUS INFORMATION ........................................................................ 19
View Internet Connection Info .......................................................... 19
View CPE Info ................................................................................. 20
View Traffic Info ............................................................................. 20
SIM/PIN SETTINGS .......................................................................... 21
Configure PIN ................................................................................. 21
Unlock SIM .................................................................................... 22
SECURITY SETTINGS .......................................................................... 23
ADMINISTRATOR SETTINGS .................................................................. 24
Change Web Management Password ................................................. 24
Enable Remote Access ..................................................................... 24
Manage LED Light ........................................................................... 25
Select Operation Mode..................................................................... 25
ADVANCED DIAGNOSIS ....................................................................... 26
Enable SysLog ................................................................................ 26
View System Log ............................................................................ 27
Use Ping Test ................................................................................. 27
Use Traceroute Test ........................................................................ 27
EN-2
SYSTEM MAINTENANCE ....................................................................... 28
Backup Configuration ...................................................................... 28
Restore Configuration ...................................................................... 28
Update APN.................................................................................... 29
Restore Factory Defaults .................................................................. 29
Upgrade CPE Firmware .................................................................... 29
NAT SETTINGS ................................................................................ 30
Configure Single Port Forwarding ...................................................... 30
Configure Port Range Forward .......................................................... 31
Configure Port Range Trigger ........................................................... 32
Enable UPnP ................................................................................... 33
Configure DMZ ............................................................................... 33
ENGINEERING MODE .......................................................................... 34
APPENDIX ............................................................................. 35
FAQ ............................................................................................. 35
TROUBLESHOOTING ........................................................................... 36
SPECIFICATIONS ............................................................................... 37
SAFETY INFORMATION ........................................................................ 39
FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT ................. 40
EN-3
LTE Outdoor CPE
About this Manual
The content of this User Manual has been made as accurate as possible.
However, due to continual product improvements, specifications and other
information are subject to change without notice.
EN-4
LTE Outdoor CPE
Product Overview
Congratulations on your purchase of this LTE outdoor CPE.
With this LTE (Long Term Evolution) CPE (which is also known as 4G CPE), you
can share high speed mobile broadband connectivity in a wide range of
computing environment. Before you begin using the LTE outdoor CPE, read this
chapter to familiarize yourself with the device.
Features

Embedded high gain directional antenna

IP66 protection against dust and water

Easy configuration based on Web Interface

Provide 10 – 30dB more coverage gain compared to indoor CPE

Support Passive Power over Ethernet.

Easy installation and use
Package Contents
The following items come with your package. If any of them is damaged or
missing, please contact your retailer.
Mounting bracket
LTE Outdoor CPE
Optional:
Plug head water
resistant kits (RJ-45)
Passive PoE adapter
NOTE
 The pictures are for reference only, actual items may slightly differ.
EN-5
LTE Outdoor CPE
Parts and Functions




   
No.
Item
Description
1
Power
Blue LED lights up when the power is on.
2
Signal strength
More lighted LEDs indicate stronger signal.
3
Mount base
Attach the mount bracket.
4
Earth ground
terminal
Use a spring washer and an M4x8L screw to
ground and protect your CPE from lightning. See
“Grounding the CPE” on page 11 for more details.
5
Ethernet port
Connect to a computer/ Passive PoE using an
Ethernet cable.
6
Reset button
 Short press to restart the device.
 Long press for 5 seconds to reset the settings to
factory default settings.
7
SIM card slot
SIM card placement.
8
USB port
For technician use only.
EN-6
LTE Outdoor CPE
Mounting and Installation
This CPE is weatherproof and designed for outdoor use. You can mount it to a
wall or to a pole.
Mounting kit includes the following items:
A. Kit-1
Quantity: 1
B. Kit-2
Quantity: 1
C. Hex Head Bolt (M8x50mm)
Quantity: 2
D. M8 Spring Washer
Quantity: 3
E. Washer M8x22 (OD) mm
Quantity: 2
F. M8 Hexagon Nuts
Quantity: 2
G. Hex Head Bolt (M5x35mm)
Quantity: 2
H. Spring Washer (M5)
Quantity: 6
I. Kit-3
Quantity: 1
J. Washer (M8)
Quantity: 1
K. Hex. Head Bolt (M5x20mm)
Quantity: 4
L. Washer (M5)
Quantity: 4
M. Kit-4
Quantity: 1
N. 1/2” U Bolt DN63
Quantity: 1
O. M13 Washer
Quantity: 2
P. M13 . Spring Washer
Quantity: 2
Q. 1/2 Hexagon Nuts
Quantity: 2
NOTE
 The illustrations are for reference only, actual items may slightly differ.
EN-7
LTE Outdoor CPE
Before installing the CPE, consider the ambient temperature, device weight,
antenna clearance, and device orientation on wall/pole for proper installation.
1. Choose a hard and stable wall or pole to mount the CPE.
2. The ambient temperature must be within -40°C to 55°C.
3. Mount on a wall or pole that can sustain the weight of the CPE.
4. Mount upright on a wall or pole that has a clear view of the signal source.
Wall Mounting
1.
2.
Align the mounting bracket on the wall. Using the bracket as mounting
template, mark the positions to drill the holes.
Assemble the bracket as shown in the illustration.
3.
Attach the bracket to the back of the
CPE.
4.
Hang the CPE to the wall and secure the
bracket using the designated screws
and washers.
EN-8
LTE Outdoor CPE
Pole Mounting
To mount the CPE to a pole, follow the steps below:
1. Assemble the mounting bracket as shown in the illustration.
2.
3.
Attach the bracket to the back of the CPE.
Align a pole on the bracket and assemble the pole bracket as shown.
4.
Adjust the CPE position to an appropriate direction and secure the pole
bracket using the designated screws and washers.
EN-9
LTE Outdoor CPE
Getting Started
This chapter will guide you on how to use your outdoor CPE.
Install the SIM card
This CPE is specially designed for the 4G LTE network.
NOTE
Check the availability of service and plan rates of data connections with your
network service provider.
1.
Unscrew the SIM card slot.
2.
Insert a valid SIM card into the SIM card slot.
Push it fully until it clicks into place.
3.
Screw the cap back on tightly.
Remove the SIM card
Push to eject the SIM card from the slot.
NOTE
 Once the SIM is reinserted, you must restart the CPE to read the SIM card
properly.
EN-10
LTE Outdoor CPE
Assemble the Optional RJ-45 Water
Resistant Kit
1.
Unpack the RJ-45 water resistant kit.
2.
Assemble one end of the Ethernet cable as shown in the illustration.
NOTE
 The Ethernet cable is not included in the package.
 For details on the head assembly, refer to the Quick Installation Guide that is
included with the RJ-45 head water resistant kit.
Grounding the CPE
For safety use, use the earth ground terminal to ground the CPE housing before
making any connections.
You need the following:
 Spring washer
 M 4x8 L screw
NOTE
 The spring washer and M4x8L screw are not included in your package.
To ground the CPE:
1.
2.
3.
4.
Insert the washer to the M4x8L screw.
Attach the screw halfway into the
earth ground terminal.
Insert the grounding cable under
the washer.
Tighten the screw.
EN-11
LTE Outdoor CPE
Connect the Computers
To use the Internet connection and configure the CPE settings, you must connect
your CPE to a computer.
Prepare two Ethernet cables for connection.
1. Unscrew the Ethernet port and insert one end of the Ethernet cable into the
port.
2.
Insert the other end of the Ethernet cable to the P+D OUT port of the PoE.
3.
Connect another Ethernet cable to a Network Hub/Router or directly to a
PC/Laptop via PoE adapter (Data/IN port).
4.
Plug the adapter to an electrical outlet.
Single Computer Connection
Multiple Computers Connection
EN-12
LTE Outdoor CPE
Using Web-based
Management
This chapter will guide you on how to configure your CPE via the web-based
utility.
Login
1. Launch a web browser.
2. On the address bar, enter http://192.168.168.168, then press Enter.
3. On the opening screen, enter the username (admin) and password (admin).
4. Click OK to login to the main screen.
5. Select preferred language, and click Apply.
EN-13
LTE Outdoor CPE
6. Click one of the header tabs and click the left navigation submenu items to
configure the system.
Header categories
Submenu items
Submenu categories
EN-14
LTE Outdoor CPE
Basic Network Settings
With Basic Mode, you can configure the basic settings of CPE and view CPE
status.
Configure Mobile Internet Settings
Set up your 4G mobile broadband connection.
1. Click Basic Mode tab and select Network Settings.
2. Click Mobile Internet Settings.
3. Configure the APN setting.
If there is a need for manual setting, enter the APN name, User Name and
Password.
4. Click APPLY to save changes.
NOTE
 If you are not sure of the details, contact your 4G internet service provider
for more information.
EN-15
LTE Outdoor CPE
Configure CPE IP Settings
Modify the IP address configuration of your CPE.
1. Click Basic Mode tab and select Network Settings.
2. Click CPE IP Settings.
3. Modify the necessary settings.

IP Address: Enter the IP address of the CPE.
By default, the IP address is 192.168.168.168.

Subnet Mask: Display the mask used to divide the IP address.

Device Name: Type a device name to use to access the web-based
utility instead of entering the IP address on the address bar. In the case
of the above illustration, you may type http://E500.CPE on the address
bar to access the web-based utility.
4. Click APPLY to save changes.
EN-16
LTE Outdoor CPE
Configure DHCP Services
Configure your CPE to use the Dynamic Host Configuration Protocol (DHCP).
With DHCP service, your CPE will automatically assign an IP address to each
computer on your network.
1. Click Basic Mode tab and select Network Settings.
2. Click DHCP Services.
3. Modify the necessary settings.

DHCP Server: Select to enable/disable the DHCP server.

Start IP Address: Assign the first IP from the range to be leased.

Maximum Number of Users: Enter the maximum number of IP
addresses to be leased.

Client Lease Time: Set the amount of time that the IP address will still
be reserved for the computer after it has been disconnected from the CPE.
4. Click APPLY to save changes.
EN-17
LTE Outdoor CPE
Configure CPE Time
Adjust the current system date and time.
1. Click Basic Mode tab and select Network Settings.
2. Click Time.
3. Modify the necessary settings.

Current Time: Display the current date and time. Click SYNC WITH
HOST to synchronize with the computer date and time.

Time Zone: Select your local time zone from the list.
4. Click APPLY to save changes.
EN-18
LTE Outdoor CPE
Status Information
View the CPE status information.
View Internet Connection Info
Display information on 4G status, 4G signal strength, network, and internet
connection.
1. Click Basic Mode tab and select Status.
2. Click Mobile Internet. The following sections are shown:

Signal Quality: Displays the Rx signal strength.

U/SIM Status: Displays the SIM card status.

Register Network: Displays the network information and status.
Home/Roaming displays whether the network is in Home or Roaming
mode.

Internet Connection: Displays the Internet connection information,
such as type, IP address, gateway, and DNS server.
EN-19
LTE Outdoor CPE
View CPE Info
Display your CPE firmware version, local network settings, and DHCP client
information.
1. Click Basic Mode
tab and select
Status.
2. Click CPE.
View Traffic Info
Display your CPE memory and network (WAN/LAN) data usage.
1. Click Basic Mode
tab and select
Status.
2. Click Traffic
Usage.
EN-20
LTE Outdoor CPE
SIM/PIN Settings
You can protect the 4G SIM card installed on your CPE from unauthorized users
by requiring the PIN code or entering a password.
Configure PIN
Set the PIN code to enable SIM card lock.
1. Click Advanced Mode tab and select Mobile Internet Settings.
2. Click PIN Management.
3. Modify the necessary settings.

U/SIM PIN Verification: Enter the PIN code.

U/SIM PIN Management: Enable/Disable PIN protection after typing a
PIN code and clicking APPLY. The PIN Protection field shows the state
you want to change to.

U/SIM’s Change PIN: Change the PIN code.
4. Click APPLY to save changes.
EN-21
LTE Outdoor CPE
Unlock SIM
Unlock SIM is applicable only for other types of SIM to which the services are
originally locked. When the SIM card is accessed and an invalid SIM is displayed
on the screen, you must enter the SIM unlock password to unlock the SIM card.
1. Click Advanced Mode tab and select Mobile Internet Settings.
2. Click SIM Management.
3. Enter the password.
4. Click UNLOCK to unlock the SIM card.
NOTE
 If you are not sure of the details, contact your 4G internet service provider
for more information.
EN-22
LTE Outdoor CPE
Security Settings
Configure firewall settings to suit your requirement.
1. Click Advanced Mode tab and select Security.
2. Click Firewall.
3. Modify the necessary settings.

Ping from WAN Filter: Select to enable/disable Ping permit from WAN.
If this function is enabled, you can remotely ping the network device from
the WAN side.

Block port scan: Port scanning means intruder across the network is
scanning your computer for open ports possibly to see if there are any
services running on your computer for hacking. Select whether to enable
or disable the block port scan function.

Block SYN Flood: SYN Flood is a common Denial of Service (DoS) attack
in which an attacker sends a succession or flood of SYN packets.
Select whether to enable or disable the block SYN flood function.

SPI Firewall: SPI (Stateful Packet Inspection) Firewall filters more kinds
of attacks by closely examining packet data structures. Select whether to
enable or disable the SPI Firewall function.
4. Click APPLY to save changes.
EN-23
LTE Outdoor CPE
Administrator Settings
Change the administrator password, configure remote access setting, set the
timer duration for LED light, and select the operation mode of your CPE.
Change Web Management Password
Change the administrator password.
1. Click Advanced Mode tab and select Admin.
2. Click Management.
3. On Administrator Settings, do the following:

Password: Enter the new password.

Confirm Password: Enter again the new password for confirmation.
4. Click APPLY to save changes.
Enable Remote Access
Configure remote access settings.
1. Click Advanced Mode tab and select Admin.
2. Click Management.
EN-24
LTE Outdoor CPE
3. On Remote Access, select Enable from the drop-down list to enable
remote management function.
4. Click APPLY to save changes.
Manage LED Light
Set the duration for the LED light to stay on.
1. Click Advanced Mode tab and select Admin.
2. Click Management.
3. On LED Light On Timer, select the desired length of time from the
drop-down list.
4. Click APPLY to save changes.
Select Operation Mode
Set the operation mode of the CPE.
1. Click Advanced Mode tab and select Admin.
2. Click Management.
3. On Operation Mode, select one of the following options:

Bridge: Select Bridge mode if you will have another router in your
network to be set as the DHCP server. Clients in your network will directly
receive IP address assigned by the server. After selecting Bridge mode,
you may connect other routers or network devices. To access the CPE
web-based utility in bridge mode, you must configure the IP address of
the computer connected to the CPE with the IP address of the CPE.

Router: Select Router mode to use the CPE as a router. This is the
default mode.
4. Click APPLY to save changes.
EN-25
LTE Outdoor CPE
Advanced Diagnosis
Set the system log, view the system log entries, and configure Ping and
Traceroute tests settings.
Enable SysLog
Configure the system log settings.
1. Click Advanced Mode tab and select Admin.
2. Click Diagnosis.
EN-26
LTE Outdoor CPE
3. On Enable Syslog, do the following:

Enable Syslog: Click Enable to enable the system log.

Syslog IP: Specify the IP address of the server that will receive the
system log.
4. Click APPLY to save changes.
View System Log
View the current system log entries.
1. Click Advanced Mode tab and select Admin.
2. Click Diagnosis.
3. On System Log, it displays the current system log entries.

Click REFRESH to refresh the log shown on the screen.

Click CLEAR to clear the current system log data.
Use Ping Test
Allow the CPE to ping the network devices to verify their connection.
1. Click Advanced Mode tab and select Admin.
2. Click Diagnosis.
3. On Ping test, do the following:

IP or Address: Enter the IP address of the network device that you want
to ping.

Packet size: Enter the packet size.

Number of Pings: Enter the number of pings.
4. Click APPLY to ping other network device.
Use Traceroute Test
Allow the CPE to trace the route that test packets take from one web destination
to another. This function is commonly used to troubleshoot network problems
and identify routing problems or firewalls that may be blocking access to a web
site.
1. Click Advanced Mode tab and select Admin.
2. Click Diagnosis.
3. On Traceroute test, enter the IP or the domain name on IP or Address.
4. Click APPLY to monitor a network trace.
EN-27
LTE Outdoor CPE
System Maintenance
Configure the settings to back up and restore the CPE configurations, upgrade
the APN and CPE firmware, and reset the CPE to factory default settings.
Backup Configuration
Back up the CPE configuration to your computer.
1. Click Advanced Mode tab and select Admin.
2. Click Recover & Renewal.
3. On Backup, click EXPORT to export the current configurations to your
computer.
Restore Configuration
Restore the previously saved backup of the CPE configuration.
1. Click Advanced Mode tab and select Admin.
2. Click Recover & Renewal.
EN-28
LTE Outdoor CPE
3. On Restore, click the Browse button and select the previously saved
configuration file in your computer.
4. Click IMPORT to update the CPE configuration.
Update APN
Update the APN database.
1. Click Advanced Mode tab and select Admin.
2. Click Recover & Renewal.
3. On APN Update, click START UPGRADE to update the APN.
Restore Factory Defaults
Reset your CPE to the factory default settings.
1. Click Advanced Mode tab and select Admin.
2. Click Recover & Renewal.
3. On Factory Defaults, click LOAD DEFAULT to reset all configuration
parameters to the factory defaults settings.
Upgrade CPE Firmware
Update the firmware of your CPE.
1. Click Advanced Mode tab and select Admin.
2. Click Recover & Renewal.
3. On Firmware Upgrade, click the Browse button and select the latest
firmware in your computer.
4. Click START UPGRADE to upgrade the CPE firmware.
EN-29
LTE Outdoor CPE
NAT Settings
Configure the network address translation (NAT) settings of the CPE.
Configure Single Port Forwarding
Single Port Forward allows users on the Internet to access this server by using
the WAN port address and the matched external port number. When users send
these types of request to your WAN port IP address via the Internet, the CPE
will forward those requests to the appropriate servers on your LAN. Configured
single port forward settings are listed on the table at the bottom of the screen.
1. Click Advanced Mode tab and select NAT.
2. Click Single Port Forward.
3. To configure the port forwarding, do the following:

Application: Enter a rule name.

LAN IP: Enter the local network IP address of the system hosting the
server.
EN-30
LTE Outdoor CPE


Port

External: Enter the external port to be redirected to Internal port.

Internal: Enter the port used by the device to receive data.

Protocol: Select the protocol from the drop-down list.
Single Port Forward

Firewall enable or disable: Select Enable from the drop-down list
to enable firewall.
4. Click APPLY to save the configuration rules.
Configure Port Range Forward
Port Range Forward allows users on the Internet to access this server by using
the WAN port IP address and the pre-defined range of ports. When users send
these types of request to your WAN port IP address via the Internet, the CPE
will forward those requests to the appropriate servers on your LAN. Configured
port range forward settings are listed on the table at the bottom of the screen.
1. Click Advanced Mode tab and select NAT.
2. Click Port Range Forward.
EN-31
LTE Outdoor CPE
3. To configure the port forwarding, do the following:

Application: Enter a rule name.

LAN IP: Enter the local network IP address of the system hosting the
server.

WAN Port


Port Range: Enter the start-port and end-port used by the public
port from the WAN side.

Protocol: Select the protocol from the drop-down list.
Port Range Forward

Enabled/Disabled: Select Enable from the drop-down list to enable
firewall.
4. Click APPLY to save the configuration rules.
Configure Port Range Trigger
Port trigger allows the device to monitor firstly if traffic on certain ports of a
computer is being triggered or being sent out; if so, the incoming traffic from
the Internet on certain ports will be allowed to pass into the same computer.
1. Click Advanced Mode tab and select NAT.
2. Click Port Range Trigger.
EN-32
LTE Outdoor CPE
3. To configure the settings, do the following:


Application

Application: Enter a rule name.

Protocol: Select the trigger port protocol from the drop-down list.

Triggered Range: Enter the start-port and end-port that will trigger
the device to open ports for incoming data.

Forwarded Range: Enter the start-port and end-port used by the
public port from the WAN side.
Port Range Trigger

Enabled/Disabled: Select Enable from the drop-down list to enable
firewall.
4. Click APPLY to save the configuration rules.
Enable UPnP
Universal Plug and Play (UPnP) allows automatic discovery and control of
services available on the network from other devices without user intervention.
1. Click Advanced Mode tab and select NAT.
2. Click UPnP.
3. On UPnP, select Enable from the drop-down list to enable the UPnP feature.
4. Click APPLY to save changes.
Configure DMZ
A DMZ (Demilitarized Zone) sets a single computer, called a DMZ host, on your
network to receive unrestricted incoming traffic from the Internet.
1. Click Advanced Mode tab and select NAT.
2. Click DMZ.
EN-33
LTE Outdoor CPE
3. On DMZ Settings, do the following:

DMZ Settings: Select Enable from the drop-down list to enable the DMZ
function.

DMZ Address: Enter the IP address of the DMZ host.
4. Click APPLY to save changes.
Engineering Mode
Reset all cellular information.
1. Click Engineering Mode tab.
2. Click Cell Information.
3. Click RESET to reset the cellular information.
EN-34
LTE Outdoor CPE
Appendix
FAQ
This chapter contains a list of frequently asked questions when you set up your
CPE configuration.
Q: What and how to find my computer IP address?
A: IP address is the identifier for a computer or device on a TCP/IP network.
Networks using the TCP/IP protocol route messages based on the IP address
of the destination. The format of an IP address is a 32-bit numeric address
written as four numbers separated by periods. Each number can be zero to
255.
For example, 192.168.168.254 could be an IP address.
To find your computer IP address,
 In Windows, click Start > Run to launch the Command program.
 Type “ipconfig”, then press the Enter button.
 Your computer IP address is listed on the IP Address.
Q: What is Long Term Evolution (LTE)?
A: LTE is a 4th generation (4G) mobile broadband standard and is the successor
to the 3G technologies CDMA/GSM/UMTS. The service is typically much faster
on both uplink/download speeds.
Q: What is a firewall?
A: A firewall is a set of related programs that protects the resources of a private
network from users from other networks.
Q: What is Network Address Translation (NAT)?
A: Network Address Translation (NAT) is the process where a network device,
usually a firewall, assigns a public address to a computer (or group of
computers) inside a private network.
Q: What is Universal Plug and Play (UPnP)?
A: UPnP is an open networking architecture that consists of services, devices,
and control points. The ultimate goal is to allow data communication among
all UPnP devices regardless of media, operating system, programming
language, and wired/wireless connection.
EN-35
LTE Outdoor CPE
Troubleshooting
This chapter contains a list of common problems that you might experience
when using your CPE, and techniques to try and overcome the problem. If you
need additional help, contact your retailer.
Problems
I cannot acquire network
connection.
The Power LED did not light up
when I plugged the adapter.
I cannot access the web
management page.
I forgot my login username
and/or password.
Solutions
Make sure that a 4G SIM card is properly
inserted to the CPE.
• Check if the Ethernet cable is properly
connected.
• If you are using a PoE adapter, make sure
that the Ethernet cables are properly
connected and the power adapter is plugged
into an appropriate power source.
5. Ensure you obtained the correct Access
Point Name (APN) supplied by the SIM card
carrier.
Make sure that the power adapter is
connected to the CPE and plugged in to an
appropriate power source. Use only the
supplied power adapter.
Check that the power source is receiving
sufficient power.
If the error persists, you may have a hardware
problem. In this case, you should contact
technical support.
Make sure you are using the correct IP
address of the CPE.
Your computer and the CPE IP addresses must
be on the same subnet for local network (LAN)
access. You can check the subnet in use by
the CPE on the Basic Network settings.
Press the Reset button for five seconds to
reset the settings to the factory default
settings. Access the web management page.
You can now login with the factory default
username and password “admin”.
EN-36
LTE Outdoor CPE
Specifications
Features
Specifications
Cellular Connectivity and Data Speed
Model
E503
E504
E507
E512
E513
E520
E538
E540
LTE band
Band 3
Band 4
Band 7
Band 12
Band 17
Band 13
Band 20
Band 38
Band 40
-
-
-
-
-
-
-
-
EVDO Band
DL Peak
Data Rate
UL Peak
Data Rate
LTE
Bandwidth
Module
E525
Band 25
Band 2
BC1
(1900)
100Mbps
50Mbps
Up to 20 MHz supported (real allocation depents on LTE channel planning)
M501LC
Antenna
Water Resistant
M505LC
M501LC
M525LC
M501LC
M509LC
M508LC
M528LC
Antenna Type
Embedded high gain directional antenna
Antenna Gain
10~13dB gain (depends on model type)
RX Diversity Antenna
Built-in design
MIMO
Downlink 2x2 SU-MIMO
IP Code
IP66
Ethernet Port
Interface
M505U
RJ45 x 1 (with power riding on Ethernet
cable)
SIM Slot
Yes
USB 2.0
Micro USB 2.0 for debug purpose
Reset Button
Reset to factory default setting
Signal strength indicators: LED x 5
LED Indicator
Power indicator: LED x 1
LED light up timer: 5 min / 15 min / 30 min
(default) / 60 min
Multiple VPN pass-through (IPSec, PPTP,
Router Features
Security
L2TP), Firewall Protection (Block Port
Scan/Block SYN Flood/Filter Ping from WAN),
SPI Firewall
NAT-NAPT
Single Port Forward, Port Range Forward, Port
Range Trigger, DMZ, UPnP
DHCP
DHCP Server/Client
Other features
IPv4, TCP, UDP, ICMPv4, ARP, HTTP/HTTPs
EN-37
LTE Outdoor CPE
Features
CPE Management
Specifications
Two modes of operation: Bridge or Router
CPE Operation Mode
mode
Two types of user account: User and Operator.
System Protection
Evey user account has his own password protected
mechanism
Browser-based
Browser supported: IE, Firefox, Safari, Chrome
Administration GUI
Browser-based
Administration GUI
English
Multi-Language Support
Remote
Management
Power Input
HTTP
Web Browser Interface
Command Line Interface
Telnet, SSH
Passive Power over
Yes, both 12V and 48V passive PoE input
Ethernet Support (PPoE)
power supported
CPE power consumption
Operation Temperature
Environment
Max 6.6 Watts when heater is off
Max 23 Watts when heater is on
-40oC to 65oC (-40oF to 149oF)
( Excluding Power
adaptor)
Power Adapter Operation
0°C to 40°C (32°F to 104°F)
Temperature
Storage Temperature
-40°C to 70°C (-40°F to 158°F)
Operating Humidity
10% to 80% (Non-Condensing)
Storage Humidity
5% to 90% (Non-Condensing)
Dimensions
423.5 (L) x 309.5 (W) x 104 (H) mm
Weight
2kg
Certification
FCC, RoHS
Specifications are subject to change without prior notice.
EN-38
LTE Outdoor CPE
Safety Information
Read and understand all safety information. Failure to follow all instructions listed
below may result in electric shock, fire and/or serious personal injury.
Power Cord Protection



Do not connect the power supply cord on elevated surfaces.
Avoid any obstructions in its path and no heavy items should be placed on
the cord.
Protect the power cord from being walked on or pinched.
Object Entry

Never insert objects of any kind through the openings of the CPE, as they
may touch dangerous voltage points that could result in a fire or electric
shock.
Operating Environment

Do not mount the CPE near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that produce heat.
Accessories

Use only accessories specified by the manufacturer.
Cleaning

Unplug the CPE from the power outlet before cleaning. Use only a dry cloth
to clean the device.
Servicing



Never attempt to disassemble the CPE yourself.
In the unlikely event that smoke, abnormal noise, or strange odor is present,
immediately turn off the CPE.
Refer all servicing to qualified service personnel.
EN-39
LTE Outdoor CPE
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:
‐
‐
‐
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
‐
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
This transmitter must not be co‐located or operating in conjunction with any other antenna
or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
EN-40
">