Nice POA1 Instructions And Warnings For Installation And Use

POA1
Control unit
EN - Instructions and warnings for installation and use
GENERAL SAFETY WARNINGS AND PRECAUTIONS
Original instructions
Safety warnings
• IMPORTANT! – This manual contains important instructions and warnings for personal safety. Incorrect installation could cause serious physical
injury. Read all parts of the manual carefully before starting work. If in doubt,
interrupt installation and contact the Nice Service Centre for clarifications.
• IMPORTANT! – Important instructions: keep this manual in a safe place
to enable future product maintenance and disposal procedures.
Summary
GENERAL SAFETY WARNINGS AND PRECAUTIONS . . . . . . . . . 1
1 – PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2 – INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2.1 - PRELIMINARY CHECKS FOR INSTALLATION . . . . . . . . . . . . . . 2
2.2 - PRODUCT APPLICATION LIMITS . . . . . . . . . . . . . . . . . . . . . . . 2
2.3 - ELECTRICAL CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.3.1 - Notes on connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.3.2 - Type of ALT input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.4 - INITIAL START-UP AND ELECTRICAL CONNECTIONS . . 3
2.5 - AUTOMATIC LIMIT SWITCH SEARCH . . . . . . . . . . . . . . . . . . . . 3
3 – TESTING AND COMMISSIONING . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.1 - TESTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation warnings
• Before commencing installation, check that the product is suitable for the
intended kind of use (see paragraph 2.2 “Limits of use” and chapter “Product
technical specifications”). If not suitable, do NOT proceed with installation.
• During installation, handle the product with care, avoiding the risk of crushing,
impact, dropping or contact with any type of liquid. Never place the product
near sources of heat or expose to naked flames. This may damage product
components and cause malfunctions, fire or hazardous situations. If this occurs, suspend installation immediately and contact the Nice Service Centre.
• Never make modifications to any part of the product. Operations other than
as specified can only cause malfunctions. The manufacturer declines all liability for damage caused by makeshift modifications to the product.
• The product should not be used by children or people with impaired physical,
sensorial or mental capacities or who have not received adequate training in
the safe use of the product.
• On the power line to the system, install a device for disconnection from the
power mains with a gap between contacts that assures complete disconnection in the conditions of overvoltage category III.
• Connect the control unit to an electric power line equipped with an earthing
system.
• The product’s packaging materials must be disposed of in full compliance
with local regulations.
3.2 - COMMISSIONING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4 – DIAGNOSTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
5 – PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
5.1 - PRESET FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1
PRODUCT DESCRIPTION
5.2 - PROGRAMMABLE FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . 4
5.2.1 - Direct programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
5.2.2 - First level programming: first part . . . . . . . . . . . . . . . . . 4
5.2.3 - First level programming: second part . . . . . . . . . . . . . . 5
5.2.4 - Second level functions . . . . . . . . . . . . . . . . . . . . . . . . . . 5
5.3 - PROGRAMMING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
5.3.1 - First level programming: functions . . . . . . . . . . . . . . . . . 6
5.3.2 - Second level programming: parameters . . . . . . . . . . . . 6
5.3.3 - Deletion of memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5.3.4 - Example of first level programming . . . . . . . . . . . . . . . . 7
5.3.5 - Example of second level programming . . . . . . . . . . . . . 7
5.3.6 - Programming diagrame . . . . . . . . . . . . . . . . . . . . . . . . . 8
6 – FURTHER DETAILS: accessories . . . . . . . . . . . . . . . . . . . . . . . . . . 9
The POA1 control unit has been designed to control POP 24 V electromechanical actuators, for automated swing gates or doors. IMPORTANT! – Any uses
other than those specified herein or in environmental conditions other
than as stated in this manual are to be considered improper and are strictly prohibited!
The POA1 control unit operates on the basis of a current sensitivity system
which checks the load of the motors connected to it. The system automatically
detects travel stops, memorises the running time of each motor and recognises obstacles during normal movement. This feature makes installation easier as
there is no need to adjust the working times nor the leaf delay.
The control unit is pre-programmed for the normal functions, while more specific functions can be chosen following a simple procedure (see chapter 5).
The control unit is designed to be powered by PS124 buffer batteries as emergency power supply in the event of a mains power failure (for further information
see chapter 6.2). It is also designed to be connected to the “Solemyo” solar
energy system (for further information see chapter 6.3).
6.1 - CONNECTING A RADIO RECEIVER . . . . . . . . . . . . . . . . . . . . . . 9
6.2 - CONNECTING MODEL PS124 BUFFER BATTERY . . . . . . . . . . 9
6.3 - CONNECTING THE SOLEMYO SYSTEM . . . . . . . . . . . . . . . . . . 9
7 – TROUBLESHOOTING (troubleshooting guide) . . . . . . . . . . . . . . . 9
8 – PRODUCT MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
DISPOSAL OF THE PRODUCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
TECHNICAL CHARACTERISTICS OF THE PRODUCT . . . . . . . . 10
EC DECLARATION OF CONFORMITY . . . . . . . . . . . . . . . . . . . . . 10
RADIO RECEIVER: SMXI - SMIXS . . . . . . . . . . . . . . . . . . . . . . . . 11
1 - PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2 - AERIAL INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3 - MEMORISING A REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . 11
4 - DELETING ALL TRANSMITTERS . . . . . . . . . . . . . . . . . . . . . . . . 12
TECHNICAL CHARACTERISTICS OF THE PRODUCT . . . . . . . . . . 12
IMAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I - VII
2
INSTALLATION
In order to explain certain terms and aspects of an automatic 2-leaf swing door
or gate system refer to the typical system shown in fig 1.
Key to fig. 1:
1. Electromechanical actuator PP7024 (with integrated POA1 control unit)
2. Electromechanical actuator PP7224 (without control unit)
3. Lucy24 flashing light
4. Key-operated selector switch
5. “PHOTO” pair of photocells
6. “FOTO1” pair of photocells
7. “PHOTO2” pair of photocells
In particular, please note that:
• Refer to the product instructions for the characteristics and connection of the
photocells.
• Activation of the “PHOTO” pair of photocells have no effect on the gate during opening, while they reverse movement during closing.
English – 1
EN
ENGLISH
EN
• Activation of the “PHOTO 1” pair of photocells stops both the opening and
closing manoeuvres.
• Activation of the “PHOTO2” pair of photocells (connected to the suitably programmed AUX input) has no effect during closing while they invert movement
during opening.
To check the parts of the control unit see fig. 2.
Key to fig. 2:
A.
B.
C.
24V power supply connector
M1 motor connector
PS124 buffer battery connector / Solemyo solar energy supply
system (for further details see chapter 6.3)
D.
500mA F type services fuse
E.
Selector switch for delaying the opening of motor M1 or M2
F.
M2 motor terminal
G.
Flashing light output terminal
H.
Gate open indicator or electric lock output terminal
I.
24Vdc terminals for services and phototest
L.
Input terminals
L1…L5.
Input and programming LEDs
M.
Terminal for radio aerial
N.
“SM” radio receiver connector
O.
Programming/diagnostics connector
P1, P2, P3. Programming buttons and LEDs
2.1 - Preliminary checks for installation
Before proceeding with installation, check the condition of the product components, suitability of the selected model and conditions of the intended installation environment:
• Ensure that all conditions of use remain within the limits of product application
and within the “Product technical specifications”.
• Ensure that the selected installation environment is compatible with the overall dimensions of the product.
• Ensure that the selected surfaces for product installation are solid and guarantee a stable fixture.
• Make sure that the fixing zone is not subject to flooding. If necessary, mount
the product raised from the ground.
• Ensure that the space around the product enables easy and safe completion
of manual manoeuvres.
• Make sure that the automation is provided with mechanical stops on both
closing and opening.
2.2 - Product application limits
The product may be used exclusively with POP 24 V gearmotors.
Key to figs. 2 - 3a - 3b - 3c:
Terminals Function
L-N1÷3
1÷3
4÷5
6÷7
8
9
10
11
12
13
14
15
16
17÷18
Power supply line
Motor 1
Motor 2
Flashing light
Open Gate indicator /
Elect.Lock
Common 24 V
(with
Everything in stand by /
phototest)
0V
24 V
Common 24 V
STOP
PHOTO
PHOTO 1
STEP BY STEP
AUX
Aerial
2.3 - Electrical connections
IMPORTANT!
– All electrical connections must be made with the unit disconnected from
the mains power supply and with the buffer battery disconnected, if present in the automation.
– Connections must be made exclusively by qualified personnel.
– Make sure that all the electric cables used are of a suitable type.
01. Loosen the screws of the cover.
02. Prepare the electrical cable routing holes.
03. Connect the cables as shown in the wiring diagram in fig. 3a - 3b - 3c. To
connect the electric power cable, see fig. 4. Note – To facilitate cable connections, the terminals can be removed from their seats.
• With the exception of the photocell inputs when the PHOTOTEST function is
activated, if the inputs of the NC (Normally Closed) contacts are not in use
they should be jumped with the “COMMON” terminal. Refer to paragraph
2.4.3 for further information.
• If there is more than one NC contact on the same input, they must be connected in SERIES.
• If the inputs of the NO (Normally Open) contacts are not used they should be
left free.
• If there is more than one NO contact on the same input, they must be connected in PARALLEL.
• The contacts must be electromechanical and potential-free. Stage connections, such as those defined as “PNP”, “NPN”, “Open Collector”, etc. are not
allowed.
• If the leafs overlap, use jumper E (fig. 2) to select which motor starts up first
during opening.
2.3.1 - Notes about connections
Most connections are extremely simple and many of them are direct connections to a single user point or contact. The following figures show examples of
how to connect external devices:
• Everything in stand by / Phototest connection
The “Everything in stand by” function is active as standard. It is excluded automatically only when the Phototest function is activated. Note - The “Everything in
stand by” and Phototest functions are alternatives as one excludes the other.
The “Everything in stand by” function allows consumptions to be reduced. Three
types of connections can be obtained:
- with “Everything in stand by” active (energy saving); see electrical diagram in
fig. 3a
- standard connection: without “Everything in stand by” and without “Phototest”;
see electrical diagram in fig. 3b
- without “Everything in stand by” and with “Phototest”; see electrical diagram in
fig. 3c
Description
Type of cable
Mains power supply
M1 motor connection
M2 motor connection (Note 1)
Connection of flashing light 24 V
max 25 W
Connection for Open Gate Indicator 24 V
max 5 W or Electric lock 12 V
max 25 VA (“See chapter 5 - Programming”)
Power Supply +24 V
for TX photocells with phototest (max. 100 mA); “COMMON”
for all inputs, safety, with “Everything in stand by” function activated (Note 2)
3 x 1,5 mm2
3 x 1,5 mm2
3 x 1,5 mm2
2 x 1 mm2
SCA:
Electric lock:
1 x 0,5 mm2
Power supply 0 V
for services
Power input for services, without “Everything in stand by” (24 V
max 200 mA)
Common for all inputs (+24 V ) without “Everything in stand by”
Input with STOP function (emergency, safety shutdown) (Note 3)
NC Input for safety devices (photocells, sensitive edges)
NC Input for safety devices (photocells, sensitive edges)
Input for cyclical functioning (OPEN-STOP-CLOSE-STOP)
Auxiliary input (Note 4)
Connection for the radio receiver aerial
1 x 0,5 mm2
1 x 0,5 mm2
1 x 0,5 mm2
1 x 0,5 mm2
1 x 0,5 mm2
1 x 0,5 mm2
1 x 0,5 mm2
1 x 0,5 mm2
screened cable type RG58
2 x 0,5 mm2
2 x 1 mm2
Note 1 – This is not used for single leaf gates (the control unit automatically recognises if only one motor has been installed).
Note 2 – The “Everything in stand by” function serves to reduce consumptions. For further details on the electrical connections refer to paragraph 2.4.1 “Everything in stand by/Phototest connection” and for programming refer to chapter 5.2.3 “Everything in stand by/Phototest function”.
Note 3 – The STOP input can be used for “NC” or constant resistance 8.2 kΩ contacts (please refer to the “Programming” chapter)
Note 4 – The AUX factory auxiliary input is programmed with the “Partial open type 1” function but can be programmed with any of the following functions:
Function
PARTIAL OPEN TYPE 1
PARTIAL OPEN TYPE 2
OPEN
CLOSE
PHOTO 2
DISABLED
2 – English
Input type
NO
NO
NO
NO
NC
—
Description
Fully opens the upper leaf
Opens the two leaf half way
Only carries out the opening manoeuvre
Only carries out the closing manoeuvre
PHOTO 2 function
No function
2.3.2 - STOP type input
The POA1 control unit can be programmed for two types of STOP input:
- NC type STOP for connecting up to NC type contacts.
- Constant resistance STOP. It enables the user to connect up to the control
unit of devices with 8.2kΩ constant resistance (e.g. sensitive edges). The
input measures the value of the resistance and disables the manoeuvre when
the resistance is outside the nominal value. Devices with normally open “NO”
or normally closed “NC” contacts, or multiple devices, even of different types,
can be connected to the constant resistance STOP input, provided that
appropriate adjustments are made; see Table 1.
WARNING! – If the constant resistance STOP input is used to connect
devices with safety functions, only the devices with 8.2 KΩ constant will
resistance output guarantee the fail-safe category 3.
second device type:
TABLE 1
1st device type:
NC
8,2 KΩ
2.4 - Initial start-up and electrical connections
IMPORTANT! – Connections must be made exclusively by qualified personnel.
After powering up the control unit, check that all the LEDs flash rapidly for a few
seconds, then perform the following checks:
1. Check that there is a voltage of approximately 30Vdc on terminals 9-10. If
not, unplug the unit immediately and carefully check the connections and
input voltage.
2. After initially flashing rapidly, the P1 LED will indicate the control unit is working correctly by flashing regularly at 1 second intervals. When there is a variation in the inputs, the “P1” led will rapidly flash twice to show that the input
has been recognised.
3. If the connections are correct, the LED for the “NC”-type inputs will be on,
while those for the “NO” type inputs must be off. See fig. A and Table 2.
A
TABLE 2
INPUT
STOP
PHOTO
FOTO1
STEP-BY-STEP
AUX
INPUT TYPE
STOP NC
CONSTANT RESISTANCE
STOP 8.2 KΩ
NC
NC
NO
OPEN PARTIALLY type 1 - NO
OPEN PARTIALLY type 2 - NO
OPEN ONLY - NO
CLOSE ONLY - NO
FOTO2 - NC
STATUS LED
L1 On
L1 On
L2 On
L3 On
L4 Off
L5 Off
L5 Off
L5 Off
L5 Off
L5 On
4. Check that the relative LEDs switch on and off when the devices connected
to the inputs are operated.
5. Check that by pressing P2 both motors perform a short opening manoeuvre,
and the motor of the upper leaf starts first. Block the manoeuvre by pressing P2 again. If the motors do not start up for opening, invert the polarities of
the motor cables. If, however, the first one to move is not the upper leaf,
operate jumper E (fig. 2).
NO
NC
8,2 KΩ
In parallel (note 1)
(note 2)
In parallel
(note 2)
In series (note 3)
In series
2.5 - Automatic search system for the limit switches
In parallel
In series
(note 4)
On the successful completion of the various controls, start the automatic
search system phase for the limit switches. This work is necessary as the POA1
control unit must “measure” how long the opening and closing manoeuvres
take This procedure is completely automatic and detects the mechanical opening and closing stops by measuring the load on the motors.
Warning! – If this procedure has already been carried out, in order to
reactivate it, the user must first delete the memory (see the “Memory deletion” chapter). In order to check whether the memory contains any limit
switch parameters, turn the power supply to the control unit on and then
off again. If all the LEDs flash rapidly for approximately 6 seconds, the
memory is empty. If, however, they only flash for 3 seconds, the memory
already contains some limit switch parameters.
Notes to Table 1:
Note 1 – Any number of NO devices can be connected to each other in parallel, with an 8.2 KΩ termination resistance (fig. 7a). For electrical connections
with the “Everything in stand by” function active, see “Everything in stand
by/Phototest function” in this paragraph 2.4.1.
Note 2 – The NO and NC combination can be obtained by placing the two contacts in parallel, and placing an 8.2 KΩ resistance in series with the NC contact.
It is, therefore, possible to combine 3 devices: NO, NC and 8.2 KΩ (fig. 7b).
Note 3 – Any number of NC devices can be connected in series to each other
and to an 8.2 KΩ resistance (fig. 7c).
Note 4 – Only one device with an 8.2 KΩ constant resistance output can be
connected; multiple devices must be connected “in cascade” with a single 8.2
KΩ termination resistance (fig. 7d).
Before starting limit switch searching, make sure that all the safety devices are
enabled (STOP, PHOTO and PHOTO1). The procedure will be immediately
interrupted if a safety device triggers or a command arrives. Ideally the doors
should be half open, although they can be in any position.
Procedure – Press the P2 button (fig. 2) to start begin searching which
includes:
- Both motors open briefly.
- Motor closes the lower leaf until it reaches the mechanical closing stop.
- The upper leaf motor closes until it reaches the mechanical closing stop.
- The motor of the upper leaf begins to open.
- After the programmed delay, opening of the lower leaf begins. If the delay is
insufficient, block the search by pressing P1 (fig. 2), then modify the time (see
chapter 5).
- The control unit measures the movement required for the motors to reach the
opening mechanical stops.
- Complete closing manoeuvre. The motors can start at different times, the aim
is to prevent the leafs from shearing by maintaining a suitable delay.
- End of the procedure with memorisation of all measurements.
All these phases must take place one after the other without any interference
from the operator. If the procedure does not continue correctly, it must be interrupted with the P1 button. Repeat the procedure, modifying some parameters if
necessary, for example the current sensitivity cut-in thresholds (see chapter 5).
English – 3
EN
When the “Everything in stand by” function is active, 1 minute after the end of a
manoeuvre the control unit goes into “Everything in stand by”, turning off the Inputs
and Outputs to reduce consumptions. The status is indicated by the “OK” LED
which begins to flash more slowly. WARNING – If the control unit is powered from
a photovoltaic panel (“Solemyo” system) or a buffer battery, the “Everything in
stand by” function must be activated as shown in the electrical diagram in fig. 3a.
When the “Everything in stand by” function is not required, the “Phototest” function may be activated. This verifies at the beginning of a manoeuvre that the connected photocells operate correctly. To use this function, first connect the photocells appropriately (see electrical diagram in fig. 3c) and then activate the function. Note – When the phototest is activated, the inputs subjected to the test
procedure are PHOTO, PHOTO1 and PHOTO2. If one of these inputs is not used
it must be connected to terminal no. 8.
• Key switch connection
Example 1 (fig. 5a): How to connect the switch in order to perform the STEPBY-STEP and STOP functions
Example 2 (fig. 5b): How to connect the switch in order to perform the STEPBY-STEP and one of the auxiliary input functions (PARTIAL OPENING, OPEN
ONLY, CLOSE ONLY …)
Note – For electrical connections with the “Everything in stand by” function
active, see “Everything in stand by/Phototest function” in this paragraph 2.4.1.
• Connection for Gate Open Indicator / Electric lock (fig. 6)
If the gate open indicator has been programmed, the output can be used as an
open gate indicator light. The light, flashes slowly during opening and quickly
during closing; If it is on but does not flash, this indicates that the gate is open.
If the light is off, the gate is closed. Se the output has been programmed as an
electric lock, it is activated for 3 seconds each time opening begins.
EN
3
4
TESTING AND COMMISSIONING
These are the most important phases of automation set-up for ensuring maximum system safety. The test can also be performed as a periodic check of
automation devices. Testing and commissioning of the automation must be
performed by skilled and qualified personnel, who are responsible for the tests
required to verify the solutions adopted according to the risks present, and for
ensuring observance of all legal provisions, standards and regulations, and in
particular all requirements of the standard EN 12445, which establishes the test
methods for checking automations for doors and gates.
The additional or optional devices must undergo a specific test for functionality
and correct interaction with POA1. Refer to the instruction manuals of the individual devices.
3.1 - Testing
The testing sequence refers to the control unit programmed with the preset
functions. See paragraph 5.1:
• Make sure that the activation of the STEP-BY-STEP input generates the following sequence of movements: “Open, Stop, Close, Stop”.
DIAGNOSTICS
The diagnostics LED P2 (fig. 2) indicates any problems or malfunctions revealed by the control unit during the manoeuvre.
A sequence with a certain number of flashes indicates the type of problem and
remains active until the following manoeuvre begins. The table below summarises this information:
Number
Led P2 flashes
1
2
3
4
5
• Make sure that the activation of the AUX input (Type 1 partial opening function)
manages the “Open, Stop, Close, Stop” sequence of the motor of the upper
leaf only, while the motor of the lower leaf remains in the closed position.
5
Type of malfunction
M1 current sensitivity device triggering
M2 current sensitivity device triggering
STOP input cut-in during the manoeuvre
Phototest error
Output overcurrent gate open indicator or electric lock
PROGRAMMING
• Perform an opening manoeuvre and check that:
- the gate continues the opening manoeuvre when PHOTO is engaged
- the opening manoeuvre stops when PHOTO1 is engaged and only continues
when PHOTO1 is disengaged
- The manoeuvre stops when PHOTO2 (if installed) is engaged and the closing
manoeuvre starts
• Make sure that the motor switches off when the door reaches the mechanical
stop.
• Perform an opening manoeuvre and check that:
- The manoeuvre stops when PHOTO is engaged and the opening manoeuvre
starts
- The manoeuvre stops when PHOTO1 is engaged and the opening manoeuvre starts again when PHOTO1 is disengaged
- the gate continues the closing manoeuvre when PHOTO 2 is engaged
• Check that the stopping devices connected to the STOP input immediately
stop all movement.
• Check that the level of the obstacle detection system is suitable for the application:
- During both the opening and the closing manoeuvres, prevent the leaf from
moving by placing an obstacle and check that the manoeuvre inverts before
exceeding the force set down by law
• Other checks may be required depending on which devices are connected to
the inputs.
Warning – If an obstacle is detected as moving in the same direction for 2
consecutive manoeuvres in the same direction, the control unit partially
inverts both motors for just 1 second. At the following command, the leafs
begin the opening manoeuvre and the first current sensitivity cut-in for
each motor is considered as a mechanical stop during the opening cycle.
The same happens when the mains power supply is switched on: the first
command is always an opening manoeuvre and the first obstacle is
always considered as a mechanical stop during the opening cycle.
3.2 - Commissioning
Commissioning can only be performed after positive results of all test
phases.
1 Prepare the automation technical documentation, which must contain the
following documents: overall drawing of the automation, electrical wiring
diagram, risk assessment and relative solutions adopted (refer to the relevant forms on our website www.niceforyou.com), manufacturer’s declaration of conformity for all devices used and installer’s declaration of conformity.
2 Affix a dataplate on the gate, specifying at least the following data: type of
automation, name and address of manufacturer (responsible for commissioning), serial number, year of construction and CE mark.
3 Before commissioning the automation, ensure that the owner is adequately
informed of all associated risks and hazards.
The POA1 control unit features some programmable functions. These functions
are pre-set in a typical configuration which satisfies most automatic systems.
These functions can be changed at any time, both before and after searching
automatically for limit switches, by carrying out the relevant programming procedure; see paragraph 5.3.
5.1 - Preset functions
•
•
•
•
•
•
•
•
•
•
•
•
•
Motor movement:
Automatic closing:
Condominium function:
Pre-flashing
Close after photo:
Opening delay:
Everything in stand by / Phototest:
Gate open indicator/Electric Lock:
STOP input:
Heavy gates:
Proportional gate open indicator:
Pause time:
Auxiliary input:
• Current sensitivity:
fast
enabled
disabled
disabled
disabled
level 2 (10%)
Everything in stand by
Gate open indicator
NC type
disabled
disabled
20 seconds
type 1 partial opening (only the
upper leaf motor is activated)
Level 2
5.2 - Programmable functions
To ensure the system is best suited to the user’s requirements, and safe in the
various different conditions of use, the POA1 control unit offers the possibility to
programme several functions or parameters, as well as the function of a number of inputs and outputs.
5.2.1 - Direct programming
• Slow/rapid movement: The user can choose the speed of movement of the
gate, at any time (with the motor arrested) simply by operating the P3 key (fig.
2) at any time the control unit is not being programmed. If LED L3 is off, this
shows that the slow movement has been set, if on the fast one has.
5.2.2 - Level one programming: part one
• Automatic closing: This function features an automatic closing cycle after
the programmed pause time; the pause time is factory set to 20 seconds but
it can be modified to 5, 10, 20, 40 or 80 seconds.
If the function is not activated, the system will run “semi-automatically”.
• “Condominium” function: This function is useful when the automatic system is radio-commanded by many different people. If this function is active,
each command received triggers an opening manoeuvre that cannot be interrupted by further commands. If the function has been deactivated, a command causes: OPEN-STOP-CLOSE-STOP.
• Pre-flashing: This function activates the flashing light before the manoeuvre
begins for a time that can be programmed to 3 seconds.
If the function is disabled, the light will start flashing when the manoeuvre
starts.
• Close after photo: During the automatic closing cycle, this function reduces
the pause time to 4 seconds after the PHOTO photocell has disengaged, i.e.
the gate closes 4 seconds after the user has passed through it. If the function
is disabled, the whole programmed pause time will pass.
• Opening delay: During opening, this function causes a delay in the activation
4 – English
5.2.3 - Level one programming: part two
• Stand By / Phototest function: The control unit has the “Everything in stand
by” function preset. If this function is active, 1 minute after the end of a
manoeuvre the control unit turns off the “Everything in stand by” output (terminal no. 8) and all the Inputs and other Outputs to reduce consumptions
(see electrical diagram in fig. 3a). This function is obligatory if the control unit
is powered exclusively with Solemyo photovoltaic panels. It is also recommended if the control panel is powered from the electric mains and if you
wish to extend emergency operation with the buffer battery PS124. As an
alternative to the “Everything in stand by” function, the “Phototest” function
may be activated. This verifies at the beginning of a manoeuvre that the connected photocells operate correctly. To use this function, connect the photocells correctly (see electrical diagram in fig. 3c) and then activate the function.
• Open gate indicator light / electric lock: If the function is activated, terminals 6-7 can be used to connect up the electric lock. If the function is deactivated, terminals 6-7 can be used to connect up a 24V gate open indicator.
• NC Type or Constant Resistance STOP Input: If the function is activated,
the STOP input is set to “8.2KΩ Constant Resistance”. In this case, there
must be a 8.2KΩ +/-25% resistance between the common and the input to
enable the operation. If the function is not set, the configuration of the STOP
input will enable it to function with NC type contacts.
• Light/heavy gates: If the function is activated, the control unit enables the
user to manage heavy gates, setting the acceleration ramps and slowdown
speeds during closing differently. If the function is deactivated, the control unit
will be set to manage light gates.
• Proportional gate open indicator: If the function is activated, the gate open
indicator output will be set with the proportional flashing light. This means that
during opening, the flashing becomes more intense as the leafs come nearer
to the opening stops; vice-versa, for closing, the flashing becomes less
intense as the leafs come nearer to the closing stops. If the function is deactivated, the light will flash slowly during opening and rapidly during closing.
5.2.4 - Level two functions
• Pause time: The pause time, namely the time which lapses between opening
and closing during automatic functioning, can be programmed to 5, 10, 20,
40, and 80 seconds.
• Auxiliary input AUX: The control unit offers an auxiliary input which can be
set to carry out one of the following 6 functions:
- Partial opening type 1: this carries out the same function as the STEP-BYSTEP input. It causes only the upper leaf to open. It only works if the gate is
closed completely, otherwise the command is interpreted as if it were a
STEP-BY-STEP comman.
- Partial opening type 2: this carries out the same function as the STEP-BYSTEP input. It causes the two leafs to open for half the time it would take
them to open completely. It only works if the gate is closed completely, otherwise the command is interpreted as if it were a STEP-BY-STEP command.
- Open only: this input only causes opening in the Open-Stop-Open-Stop
sequence.
- Close only: this input only causes closing in the Open-Stop-Open-Stop
sequence.
- Photo 2: this carries out the function of the “PHOTO 2” safety device.
- Disabled: the input will not carry out any function
• Discharge time: At the end of the Closing manoeuvre, after the leafs have
reached the totally closed position, the motor continues to “push” the leaf for
a brief interval, to ensure perfect closure. Immediately afterwards, this function activates a very brief inversion of movement to reduce excessive pressure exerted by the motor on the leafs.
• Current sensitivity: The control unit is equipped with a system which measures the current absorbed by the two motors used to detect the mechanical
stops and any obstacles when the gate is moving. Since the current absorbed depends on a number of conditions, including the weight of the gate,
friction, wind and variations in voltage, the cut-in threshold can be changed.
There are 6 levels: 1 is the most sensitive (minimum force), 6 is the least sensitive (maximum force).
By increasing the amperometric sensitivity level the deceleration speed
increases during the closing phase of the manoeuvre.
WARNING! – If the “current sensitivity” function (together with other
vital features) is adjusted correctly, the system will comply with European standards, EN 12453 and EN 12445, which require techniques or
devices to be used to limit force and danger during the functioning of
automatic gates and doors are moved.
The P1, P2 and P3 buttons are used for all the programming phases, while the
5 LEDs (L1, L2…L5) indicate the selected parameter.
There are two different programming levels:
• At level 1, the functions can be enabled or disabled. Each Led (L1, L2…L5)
corresponds to a function: if the Led is on, the function is active; if it is off, it is
deactivated.
Level one consists in 2 parts which can be selected using the P3 button. The
corresponding LED P3 indicates which of the 2 parts has been selected.
Level one (P1 Led lit): part one ( P3 Led off)
L1 Led
L2 Led
L3 Led
L4 Led
L5 Led
Closing
Automatic
Function
Condominium
Pre-flash
Close after
photo
Delay in
opening
L1 Led
L2 Led
L3 Led
L4 Led
L5 Led
Everything in
stand by /
Phototest
Electric lock
Resistance
stop
Heavy gates
Gate open
proportional
Level one (P1 Led lit): part two (P3 Led lit)
• It is possible to pass to the second level from level one of part one. At this
second level the user can choose the parameter relating to the function. A
different value corresponds to each LED which must be associated to the
parameter.
Level one (P1 Led lit): part one (led P3 off)
L1 Led
L2 Led
L3 Led
L4 Led
L5 Led
Closing
automatic
Function
condominium
Pre-flashing
Close after
photo
Delay in
opening
Level two:
Parameter:
Parameter:
Parameter:
Parameter:
Parameter:
Time
pause
L1: 5s
AUX input
Time
discharge
L1: no
discharge
L2: 0.3s
Current
sensitivity
L1: Level 1
(more sensitive)
L2: Level 2
Leaf delay
L2: 10%
L3: 20%
L2: 10s
L1: Open
partial TYPE 1
L2: Open
partial TYPE 2
L1: 5%s
L3: 20s
L3: Open Only
L3: 0.7s
L3: Level 3
L4: 40s
L4: Close Only
L4: 1.3s
L4: Level 4
L4: 30%
L5: 80s
L5: Photo 2
L5: 2s
L5: Level 5
(less sensitive)
L5: 40%
All LEDs off:
input
not used
All LEDs off:
Level 6
(max current
sensitività )
Level one (P1 Led lit): part two (P3 Led lit)
L1 Led
L2 Led
L3 Led
L4 Led
L5 Led
Everything in
stand by /
Phototest
Electric lock
Resistance
stop
Heavy gates
Gate open
proportional
• Leaf delay: The delay in starting up the motor of the lower leaf can be programmed to 5, 10, 20, 30 or 40% of the working time.
5.3 - Programming
All the functions described in paragraph 5.2 “Programmable functions” chapter
can be selected by means of a programming phase which terminates by memorising the choices made. The control unit therefore has a memory which stores
the functions and parameters relative to the automation process.
English – 5
EN
of the lower leaf motor compared with the upper one This is necessary in
order to prevent the leafs from getting stuck. There is always a standard delay
during closing, calculated automatically by the control unit in order to ensure
the same delay as the one programmed for opening.
EN
5.3.1 - Level one programming: functions
At level 1, the functions can be enabled or disabled. At level one, LED P1 is
always on; if LEDs L1, L2…L5 are on, the functions are activated; if the LEDs
are off, the functions are deactivated. A flashing LED indicates which function
has been selected, short flashes indicate the function has been deactivated;
long flashes indicate the function has been activated. Press P3 to pass from
part one programming to part two programming, and vice-versa.
TABLE A1 - Entering level one programming
01. Press and hold down buttons P1 and P2 for at least 3 seconds
The programming mode has been entered if all the Leds start flashing quickly
P1
P2
TABLE A2 - Activating or deactivating a function
01. Press P1 repeatedly until the flashing Led reaches the function required
P1
02. Press P1 repeatedly until the flashing Led reaches the function required
P2
TABLE A3 - To pass from part one to part two of level one (and vice-versa)
01. Press P3. button
P3
TABLE A4 - To exit level one and save the modifications
01. Press P1 and then immediately P2, holding them both down for at least 3 seconds
P1
P2
3s
TABLE A5 - Exiting level one and delete the modifications
01. Either press P1 for at least 3 seconds, or wait for 1 minute, or disconnect the power supply
3s
or
P1
60s
or
5.3.2 - Level two programming: parameters
The function parameter can be chosen at level two. Level two can only be
reached from level one. At level 2 the P1 Led flashes quickly while the 5 Leds
(L1, L2…L5) indicate the selected parameter.
TABLE B1 - Entering level two programming
01. Enter level one programming by pressing P1 and P2 for at least 3 seconds
P1
P2
3s
02. Select the function by pressing P1 until the flashing Led reaches the point required
P1
03. Enter level two by pressing the P2 button for at least 3 seconds
P2
3s
TABLE B2 - Selecting the parameter
01. Press P2 repeatedly until the Led reaches the desired parameter
P2
TABLE B3 - Returning to level one
01. Press P1
P1
TABLE B4 - Exiting level one and saving modifications
01. Press P1 and then immediately P2, holding them both down for at least 3 seconds
P1
P2
TABLE B5 - Exiting level one and cancelling modifications
01. Either press P1 for at least 3 seconds, or wait for 1 minute, or disconnect the power supply
3s
P1
or
60s
or
5.3.3 - Memory deletion
Each new programme replaces the previous settings. It is usually unnecessary
to “delete all” the parameters”. If required, the memory can be totally deleted by
6 – English
performing this simple operation: WARNING – As all the functions return to
their pre-set values after the memory is deleted, a new search for the limit switches must be carried out.
EN
TABLE C1 - Delete memory
01. Switch the power supply to the control box off, and wait until all the LEDs have gone off (remove fuse F1 if necessary)
02. Press P1 and P2 on the board down and keep them pressed down
P1
P2
P1
P2
03. Switch the power supply on again
04. Wait at least 3 seconds before releasing the two keys
3s
If the memory was deleted correctly, all the Leds will switch off for 1 second
5.3.4 - Example of level one programming
the “Condominium” function, for example, and prepare the “Gate Open Indica-
The following examples show how to activate or deactivate a level one function,
tor” output in order to activate the electric lock.
Example of level one programming:
activate the “Condominium” function and “Electric lock” output
01. Access the level one programming mode by pressing P1 and P2, and keeping them pressed down for at least 3 seconds
02. Press P1 once to move the flashing Led to the Led 2 (the flashes will be short)
P1
P2
3s
P1
P2
3s
P1
P2
3s
2
P1 x1
03. Activate the “Condominium” function by pressing P2 (the flashes will be longer)
P2
04. Press P3 once in order to activate part two (the P3 LED will switch on)
P3
05. Press P1 once to move the flashing Led to the Led 2 (the flashes will be short)
2
P1
06. Activate the “Electric lock” output by pressing P2 (the flashes will be longer)
P2
07. Exit programming (with memorisation) by pressing P1 and then immediately P2, holding them both down
for at least 3 seconds
5.3.5 - Example of level two programming
This example shows how to modify a level two parameter, for example, how to
modify current sensitivity intil “level 5”.
Example of level two programming: modifying “current sensitivity”
01. Access the level one programming mode by pressing P1 and P2 for at least 3 seconds
02. Press P1 three times to move the flashing Led to the Led 4
4
P1 x3
03. Access level two by pressing P2 for at least 3 seconds
04. Press P2 three times until Led 5 switches on
P2
5
P2 x3
05. Return to level one by pressing P1
06. Exit programming (with memorisation) by pressing P1 and then immediately P2, holding them both down
for at least 3 seconds
3s
P1
P1
P2
3s
English – 7
EN
5.3.6 - Programming diagram
The following figure shows the complete programming diagram of the functions
and relative parameters.
This figure also shows the functions and parameters either as they were initially
or following total memory deletion.
Normal
operation
P1
Led P1 Slow flashing
ALT
Photo Photo
1
Step
by
step
AUX
P2
P3
P1+P2
for 3 secs
P1
for 3 secs
(NO SAVE)
P1+P2
for 3 secs
(SAVE)
P1
Level one
Led P1 On permanently
Autom. Cond. PreClose
closing
flashing after
Photo
Opening
delay
P2
P3
P1
On
Off
P3
Every- Electric Resist. Heavy Proportional
Gate
thing in Lock STOP. gates
Open
stand
by /
Phototest
P2
P3
PAUSE TIME
P2
for 3 secs
P1
P1
5
10
20
40
80
P2
seconds
P3
AUXILIARY INPUT (*)
P1
Level two
Led P1 Rapid flashing
type 1 type 2 only
only Photo 2
p.o
p.o opening closing
P2
P3
DISCHARGE
P1
0
0,3
0,7
1,3
2
P2
seconds
P3
CURRENT SENSITIVITY
P1
1
2
3
4
5
P2
(*)
a.p. type 1
Level
P3
type 1 partial open, upper leaf
moves [N.O.]
a.p. type 2
type 2 partial opening, both
motors move for 1/2 the working
time set [N.O.]
Only open
open ➔ stop ➔ open ➔ stop…
[N.O.]
P2
Only closed
close ➔ stop ➔ close ➔ stop…
[N.O.]
P3
Photo 2
used as photo 2 [N.C.]
All Leds off · max. current sensitivity
OPENING DELAY
P1
5
10
20
30
40
%
8 – English
On
Off
the mechanical stops, therefore). This is considered as an obstacle and
causes an inversion. To find out if the current sensitivity device has triggered,
count how many times the Diagnostics LED flashes: 1 flash indicates that the
current sensitivity device triggered on account of motor 1, 2 flashes indicate
that this was caused by motor 2.
6.1 - Connecting a radio receiver
The control unit has a connector for fitting a 4 channel radio card complete with
SM slot. This remote control device functions by means of transmitters which
act on the inputs as per the following table:
Output Receiver
N° 1
N° 2
N° 3
N° 4
Control unit input
Step by step
AUX (reset value: Partially Open 1)
“Open only”
“Close only”
8
PRODUCT MAINTENANCE
As the POA1 control unit is electronic it requires no particular maintenance.
However, at least every six months the efficiency of the entire system must be
checked according to the information described in chapter 3.
6.2 - Connecting model PS124 buffer battery
PS124 buffer batteries can be used to supply the control unit in case of network blackouts. To install and connect the battery, proceed as shown in fig. 8.
6.3 - Connecting the Solemyo system
The control unit is designed to be powered with the “Solemyo” photovoltaic
system (photovoltaic panel and 24 V battery). To connect the Solemyo battery
to the control unit, use the socket on the control unit that is normally used for
the buffer battery (see paragraph 6.2).
IMPORTANT!
- When the automation is powered by the “Solemyo” system, it MUST
NOT BE POWERED at the same time from the electrical mains.
- The Solemyo system can be used only if the “Everything in stand by”
function on the control unit is ON and the connections are as shown in the
diagram in fig. 3a.
7
TROUBLESHOOTING
(troubleshooting guide)
No LEDs are on:
• Check whether the control unit is powered (measure a voltage of about
30Vdc at terminals 9-10 (or 24 Vdc with battery power).
• Check the 2 fuses, if not even the P1 Led is on or flashing a serious fault has
probably occurred and the control unit must therefore be replaced.
DISPOSAL OF THE PRODUCT
This product is an integral part of the automation, and therefore, they
must be disposed of together.
As for the installation operations, at the end of the life of this product, the dismantling operations must be performed by qualified personnel.
This product is made from different types of materials: some can be recycled,
others must be disposed of. Please inform yourselves on the recycling or disposal systems provided for by the laws in force in your area, for this category of
product.
CAUTION! – some parts of the product can contain polluting or dangerous
substances which, if dispersed in the environment, may cause serious harm to
the environment and human health.
As indicated by the symbol at the side, it is forbidden to
throw this product into domestic refuse. Therefore, follow the
“separated collection” instructions for disposal, according to
the methods provided for by local regulations in force, or
redeliver the product to the retailer at the moment of purchase of a new, equivalent product.
CAUTION! – the regulations in force at local level may envisage heavy sanctions in case of abusive disposal of this product.
The P1 LED flashes regularly but the input LED’s L1, L2...L5 do not reflect
the state of the respective inputs
• Switch the unit off for the moment in order to exit a possible programming
phase.
• Carefully check the connections on terminals 11 to 16.
LED P1 flashes every 4 seconds
• The control unit is in “Everything in stand by” status.
The “Automatic search” procedure does not start up
• The “Automatic search” procedure only starts if it has never been performed
before or if the memory has been deleted. To check whether the memory is
empty switch off the unit for a moment. When it is switched on again, all the
Leds should flash rapidly for about 6 seconds. If they only flash for 3 seconds, the memory already contains valid values. If a new “Automatic search”
is required, the memory must be completely deleted.
The “Automatic search” procedure has never been performed but it either
does not start or it behaves incorrectly
• The system and all the safety devices must be operative in order to activate
the “Automatic search” procedure.
• Make sure that no device connected to the inputs cuts in during the “Automatic search” procedure.
• In order for the “Automatic search” procedure to start correctly, the input
Leds must be on as shown in fig. 9, the P1 Led must flash once a second.
The “Automatic search” procedure was performed correctly but the
manoeuvre does not start
• Check that the safety device (STOP, PHOTO, PHOTO1 and, if installed,
PHOTO2) Leds are on and that the relative command Led (STEP-BY-STEP
or AUX) remains on for the entire duration of the command.
• If the “Phototest” function is activated but the photocells do not function correctly, the DIAGNOSTICS LED indicates the fault by flashing four times.
The gate inverts the direction while moving
An inversion is caused by:
• The photocells triggering (PHOTO2 during the opening manoeuvre, PHOTO
or PHOTO1 during the closing manoeuvre). In this case, check the photocell
connections and input LEDs.
• The current sensitivity device triggers while the motors are moving (not near
English – 9
EN
6
FURTHER DETAILS: accessories
EN
TECHNICAL CHARACTERISTICS OF THE PRODUCT
WARNINGS: • All technical characteristics stated refer to an ambient temperature of 20°C (±5°C). • Nice S.p.a reserves the right to modify the product at any
timee, while maintaining the same functionalities and intended use.
Mains power supply
Max absorbed power
Emergency power supply
Maximum motor current:
Service power output
Phototest Output
Flashing lamp output
Gate open indicator output
STOP Input
Working time
Pause time
Discharge time
Leaf delay in open cycle
Leaf delay in close cycle
2nd motor output
Max. cable length
POA1 Control units:
230 V ±10% 50 ÷ 60 Hz
POA1/V1 Control units: 120 V ±10% 50 ÷ 60 Hz
170 VA
for PS124 buffer batteries and for Solemyo solar kit
3A (with a “level 6” current sensitivity cut in)
24 V
200 mA maximum current (the voltage can vary from 16 to 33 V )
24 V
100 mA maximum current (the voltage can vary from 16 to 33 V )
for flashing lamp 24 V , maximum power 25 W (the voltage can vary from 16 to 33 V )
for indicator lamps at 24 V
maximum power 5 W (the voltage can vary from 16 to 33 V )
or electric locks 12 V 25 W
for NC contacts or constant resistance 8,2 KΩ +/- 25%
automatic detection
programmable at 5, 10, 20, 40, 80 seconds
programmable to 0, 0.3, 0.7, 1.3, 2 seconds
programmable at 5, 10, 20, 30 and 40 % of working time
automatic detection
for motor POP (PP7224)
230 V
power supply
30 m
Solemyo solar power kit
3m
motor
10 m
other inputs/outputs
30 m
flashing light
10 m
SCA
30 m
electric lock
10 m
aerial
20 m (recommended less than 3 m)
Radio receiver
“SM” type coupling for receivers SMXI, SMXIS, OXI (Mode I and Mode II)
Temperatura di esercizio
from - 20 to 50 °C
EC DECLARATION OF CONFORMITY
Note - The contents of this declaration correspond to declarations in the last revision of the official document deposited at the registered offices of Nice Spa available before this
manual was printed. The text herein has been re-edited for editorial purposes.
Number: 173/PP7024
Revision: 3
The undersigned, Luigi Paro, in the role of Managing Director, declares under his sole responsibility, that the product:
Manufacturer’s Name:
NICE s.p.a.
Address:
Via Pezza Alta 13, Z.I. Rustignè, 31046 Oderzo (TV) Italy
Type:
Electromechanical gearmotor with control unit
Models:
PP7024, PP7024/A
Accessories:
No accessory
Conforms to the requirements of the EC directive:
• 98/37/EC DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND COUNCIL of 22 June 1998 regarding the approximation of member state legislation related to machinery
As envisaged in the directive 98/37/EC, start-up of the product specified above is not admitted unless the machine, in which the product is incorporated, has been identified and declared as conforming to directive 98/37/EC.
The product also conforms to the requirements of the following EC directives:
• 2006/95/EEC DIRECTIVE 2006/95/EEC OF THE EUROPEAN PARLIAMENT AND COUNCIL of 12 December 2006 regarding the approximation of member state legislation related to electrical material destined for use within specific voltage limits
According to the following harmonised standards: EN 60335-1:1994+A11:1995+A1:1996+A12:1996
+A13:1998+A14:1998+A15:2000+A2:2000+A16:2001, EN 50366:2003+A1:2006
• 2004/108/EEC DIRECTIVE 2004/108/EEC OF THE EUROPEAN PARLIAMENT AND COUNCIL of 15 December 2004 regarding the approximation of
member state legislation related to electromagnetic compatibility, repealing directive 89/336/EEC
According to the following harmonised standards: EN 61000-6-2:2005; EN 61000-6-3:2007
The product also complies, within the constraints of applicable parts, with the following standards:
EN 60335-1:2002+A1:2004+A11:2004+A12:2006+ A2:2006, EN 60335-2-103:2003,
EN 13241-1:2003; EN 12453:2002; EN 12445:2002; EN 12978:2003
Oderzo, 27.03.09
10 – English
Ing. Luigi Paro (Managing Director)
1
PRODUCT DESCRIPTION
SMXI and SMXIS are 4-channel radio receivers for control units equipped with
SM-type connector. The peculiarity of compatible transmitters is that the identification code is different for each transmitter. Therefore, in order to allow the
receiver to recognise a determined transmitter, the recognition code must be
memorised. This operation must repeated for each transmitter required to communicate with the control unit.
Notes:
– Up to a maximum of 256 transmitters can be memorised in the receiver. No
one transmitter can be cancelled; all the codes must be deleted
– For more advanced functions use the appropriate programming unit.
0682
The receiver features 4 outputs, all available on the underlying connector. To
find out which function is performed by each output, see chapter 6.1.
During the transmitter code memorisation phase, one of these two options may
be chosen:
Mode I - Table B1: Each transmitter button activates the corresponding output in the receiver, that is, button 1 activates output 1, button 2 activates output
2, and so on. In this case there is a single memorisation phase for each transmitter; during this phase, it doesn’t matter which button is pressed and just one
memory sector is occupied.
Mode II - Table B2: Each transmitter button can be associated with a particular output in the receiver, e.g., button 1 activates output 2, button 2 activates
output 1, and so on. In this case, the transmitter must be memorised, pressing
the required button, for each output to activate. Naturally, each button can activate just one output while the same output can be activated by more than one
button. One memory section is occupied for each button.
TABLE B1 - Mode I memorising (All buttons are memorised on the related receiver output)
01. Press and hold down the receiver button for at least 3 seconds
RX
02. Release the button when the Led lights up
3s
RX
03. Push, for at least 2 seconds, any of the buttons of the transmitter to be memorised within 10 seconds
TX
Note – If the procedure was memorised correctly, the Led on the receiver will flash 3 times. If there are other transmitters
to memorise, repeat step 3 within another 10 seconds. The memorisation phase finishes if no new codes are received
for 10 seconds.
2s
x3
TABLE B2 - Mode II memorising (A specific receiver output can be associated to each button)
01. Press and release the receiver button as many times as the number of the desired output (Once for output No. 1,
twice for output No. 2)
RX
02. Check that the LED emits the same number of flashes as the desired output, repeated over 10 seconds in regular
intervals (1 flash if output No. 1, 2 flashes if output No. 2)
03. Within 10 seconds press the desired button on the transmitter to be memorised, holding it down for at least 2 seconds.
TX
Note – If the procedure was memorised correctly, the Led on the receiver will flash 3 times. If there are other transmitters
to memorise, repeat step 3 within another 10 seconds. The memorisation phase finishes if no new codes are received
for 10 seconds.
2
INSTALLING THE AERIAL
The receiver requires an ABF or ABFKIT type aerial to work properly; without an
aerial the range is limited to just a few metres. The aerial must be installed as
high as possible; if there are metal or reinforced concrete structures nearby you
can install the aerial on top. If the cable supplied with the aerial is too short, use
a coaxial cable with 50-Ohm impedance (e.g. low dispersion RG58), the cable
must be no longer than 10 m.
If the aerial is installed in a place that is not connected to earth (masonry structures), the braid’s terminal can be earthed to provide a larger range of action.
The earth point must, of course, be local and of good quality. If an ABF or
ABFKIT aerial cannot be installed, you can get quite good results using the
length of wire supplied with the receiver as the aerial, laying it flat.
3
2s
x3
The procedures for memorising the remote controls must be performed within
a certain time limit; please read and understand the whole procedure before
starting.
In order to carry out the following procedure, it is necessary to use the button
located on the box of the radio receiver (reference A, Fig. 1a), and the corresponding LED (reference B, Fig. 1a) to the left of the button.
1a
MEMORISING A REMOTE CONTROL
WARNING – When the memorisation phase is activated, any transmitter correctly recognised within the reception range of the radio
is memorised. Consider this aspect with care and remove the aerial if necessary to reduce the capacity of the receiver.
English – 11
EN
smxi - smixs radio receiver
EN
Remote memorising
It is possible to enter a new transmitter in the receiver memory without using
the keypad. A previously memorised and operational remote control must be
available. The new transmitter will “inherit” the characteristics of the previously
memorised one. Therefore, if the first transmitter is memorised in mode I, the
new one will also be memorised in mode I and any of the buttons of the transmitter can be pressed. If the first transmitter is memorised in mode II the new
one will also be memorised in mode II but the button activating the required
output must be pressed on the first transmitter as must the button required to
be memorised on the second. You need to read all the instructions in advance
so you can perform the operations in sequence without interruptions. Now, with
the two remote controls (the NEW one requiring code memorisation and the
OLD one that is already memorised), position yourself within the operating
range of the radio controls (within maximum range) and carry out the instructions listed in the table.
TABLE B3 - Remote Memorising
01. Press the button on the NEW transmitter for at least 5 seconds and then release
x5s
TX
02. Press the button on the OLD transmitter 3 times slowly
TX
1s
TX
TX
1s
03. Press the button on the NEW transmitter slowly and then release
TX
TX
1s
x1
Note – If there are other transmitters to memorise, repeat the above steps for each new transmitter.
4
DELETING ALL TRANSMITTERS
All the memorised codes can be deleted as follows:
TABLE B4 - Deleting all transmitters
01. Press the receiver button and hold it down
RX
02. Wait for the Led to light up, then wait for it to switch off and then wait for it to flash 3 times
x3
03. Release the button exactly during the third flash
RX
Note – if the procedure was performed correctly, the Led will flash 5 times after a few moments.
3°
x5
TECHNICAL CHARACTERISTICS OF THE PRODUCT
WARNINGS: • All technical characteristics stated refer to an ambient temperature of 20°C (±5°C). • Nice S.p.a reserves the right to modify the product at any
timee, while maintaining the same functionalities and intended use. • The range of the transmitters and the reception capacity of the receivers may be subject to
interference that may alter their performance. In the event of interference, Nice cannot guarantee the effective capacity of their devices.
Receivers:
SMXI
SMXIS
Decoding
Transmitter compatibility
Rolling code 52 bit FLOR
FLOR, VERY VR, NICE WAY, ERGO, PLANO, NICE ONE
Rolling code 64 bit SMILO
SMILO
Frequency
433.92 MHz
433.92 MHz
Input impedance
Outputs
52 KΩ
4 (on SM connector)
52 KΩ
4 (on SM connector)
Sensitivity
better than 0.5 µV
better than 0.5 µV
Working temp.
from -10°C to + 55° C
from -10°C to + 55° C
Transmitters:
FLO2R
SMILO
Buttons
1, 2 or 4 according to the versions
2 or 4
Power input
12 V
12 V
Absorption
10 mA
Transmission frequency
433.92 MHz
433.92 MHz
Working temp.
from -10°C to + 55° C
from -10°C to + 55° C
Radiated power
estimated approximately 1 mW E.R.P.
estimated approximately 1 mW E.R.P.
Range
estimated 200 m (outdoors); 35 m (indoors)
estimated 200 m (outdoors); 35 m (indoors)
Dimensions / Weight
69 x 39 x 15,5 mm / 31 g.
Ø 48 mm x H 14 mm - 14 g
Encoding
digital (4.5 x1015 combinations)
digital (18 x 1015 combinations)
12 – English
Batt. 23 A
Batt. 23 A
25 mA
EN
IT
FR
DE
ES
EN - Images
PL
IT - Immagini
NL
FR - Images
ES - Imágenes
DE - Bilder
PL - Zdjęcia
NL - Afbeeldingen
I
1
3
4
5
7
5
2
1
7
6
6
2
M1
L
M2
EN - E = Electric jumper
DE - E = Brücke
IT - E = Ponticello elettrico
PL - E = Mostek elektryczny
FR - E = Cavalier électrique
NL - E = Elektrische
geleidingsbrug
ES - E = Conexión eléctrico
N
E
F
G
H
1 2 3
4 5
6 7
I
L
M
8 9 10 11 12 13 14 15 16
L1...L5
D
P1
P2
C
P3
N
B
A
II
O
3a
EN- Connection with “Everything in stand by” active (energy saving)
TX
RX
IT - Collegamento con “Stand by tutto” attivo (risparmio energetico)
FR - Connexion avec « Stand-by total » actif (économie d’énergie)
ES - Conexión con “Stand by todo” activo (ahorro energético)
DE- Anschluss mit aktivem “Stand by - alles” (Energieeinsparung)”
PL - Połączenie z aktywną funkcją “Stand by całego urządzenia”
(oszczędność energii)
PHOTO2
NL - Aansluiting met “Alles stand by” actief (energiebesparing)
3b
EN- Standard connection: without using “Everything in stand
by” or “Phototest”
TX
RX
IT - Collegamento standard: senza utilizzare “Stand by tutto” e
senza “Fototest”
FR - Connexion standard : sans utiliser « Stand-by total » et sans
« Phototest »
ES - Conexión estándar: sin utilizar “Stand by todo” y sin
“Fototest”
DE- Standardanschluss: ohne Nutzung des “Stand by - alles”
und ohne “Fototest”
PL - Połączenie standard: bez wykorzystywania funkcji “Stand
by całego urządzenia” i bez “Fototestu”
NL - Standaard aansluiting: zonder gebruik van “Alles stand by”
en zonder "Fototest”
III
3c
TX
RX
EN- Connection without “Everything in stand by” with
“Phototest”
IT - Collegamento senza “Stand by tutto” con “Fototest”
FR - Connexion sans “Stand by todo” et avec « phototest »
ES - Conexión sin “Stand by todo” con “Fototest”
DE- Ohne “Stand by - alles” und ohne “Phototest”
PL - Połączenie bez funkcji “Stand by całego urządzenia” i z
funkcją “Fototest”
NL - Aansluiting zonder “Alles stand by” met “Fototest”
4
EN- For the ALT connection with “Everything in stand by” active,
connect terminal no. 8 and not no. 11
5a
STEP BY STEP
ALT
NC NO
C
C
NO NC
IT - Per il collegamento ALT, con “Stand by tutto” attiva, collegare il
morsetto n° 8 e non il n° 11
FR - Pour la connexion HALTE, avec « Stand-by total » actif,
connecter la borne n° 8 et pas la n° 11
ES - Para la conexión ALT, con “Stand by todo” activo, conecte el
borne n° 8 y no el n° 11
DE- Für den Anschluss STOPP, bei aktivem “Stand by - alles”, die
Klemme Nr. 8 und nicht 11 anschließen
15
11
PL - Aby wykonać połączenie STOP z aktywną funkcją ““Stand by
całego urządzenia”należy połączyć zacisk nr 8 a nie nr 11
11
NL - Voor de aansluiting ALT, met actieve “Alles stand by”, sluit u de
klem 8 aan en niet de klem 11
12
IV
5b
6
STEP BY STEP
6
AUX
NC NO
C
C
NO NC
7
33 V
12 V~
max 5 W
max 25 VA
6
15
11
7
11
16
7a
7b
7c
NC
11
11
NA
11
NA
NA
12
12
NC
8,2KΩ
8,2KΩ
NC
8,2KΩ
12
EN- With “Everything in stand by” active connect terminal no. 8 and
not no. 11
DE- Bei aktivem “Stand by - alles”, die Klemme Nr. 8 und und nicht 11
anschließen
IT - Con “Stand by tutto” attiva collegare il morsetto n° 8 e non il
n° 11
PL - Z aktywną funkcją “Stand by całego urządzenia” należy
połączyć zacisk nr 8 a nie nr 11
FR - Avec « Stand-by total » actif connecter la borne n° 8 et pas la
n° 11
NL - Met actieve “Alles stand by” sluit u klem 8 aan en niet klem 11
ES - Con “Stand by todo” activo, conecte el borne n° 8 y no el n° 11
7d
11
12
1
2
n
Sensitive edge
Sensitive edge
Sensitive edge
IT - Bordo sensibile
IT - Bordo sensibile
IT - Bordo sensibile
FR - Bord sensible
FR - Bord sensible
FR - Bord sensible
ES - Banda sensible
ES - Banda sensible
ES - Banda sensible
DE - Schaltleiste
DE - Schaltleiste
DE - Schaltleiste
PL - Listwa optyczna
PL - Listwa optyczna
PL - Listwa optyczna
NL - Contactlijst
NL - Contactlijst
NL - Contactlijst
8,2KΩ
V
8
C
9
VI
A
B
D
Nice Worldwide
Nice SpA
Oderzo TV Italia
Ph. +39.0422.85.38.38
Fax +39.0422.85.35.85
[email protected]
Nice France
Buchelay France
Ph. +33.(0)1.30.33.95.95
Fax +33.(0)1.30.33.95.96
[email protected]
Nice in Italy
Nice France Sud
Aubagne France
Ph. +33.(0)4.42.62.42.52
Fax. +33.(0)4.42.62.42.50
[email protected]
Nice Padova
Padova Italia
Ph. +39.049.87.01.05.1
Fax +39.049.87.07.63.8
[email protected]
Nice Roma
Roma Italia
Ph. +39.06.72.67.17.61
Fax +39.06.72.67.55.20
[email protected]
Nice France Rhône Alpes
Decines Charpieu France
Ph. +33.(0)4.78.26.56.53
Fax +33.(0)4.78.26.57.53
[email protected]
Nice Belgium
Leuven (Heverlee) Belgium
Ph. +32.(0)16.38.69.00
Fax +32.(0)16.38.69.01
[email protected]
www.niceforyou.com
Nice Deutschland
Gelnhausen Deutschland
Ph. +49.(0)6051.91.520
Fax +49.(0)6051.91.52.119
[email protected]
Nice España Madrid
Mostoles Madrid España
Ph. +34.(0)9.16.16.33.00
Fax +34.(0)9.16.16.30.10
[email protected]
Nice España Barcelona
Sant Quirze del Valles
Barcelona España
Ph. +34.(0)9.37.84.77.75
Fax +34.(0)9.37.84.77.72
[email protected]
Nice Australia
Wetherill Park Australia
Ph. +61.(0)2.96.04.25.70
Fax +61.(0)2.96.04.25.73
[email protected]
Nice China
Shanghai P. R. China
Ph. +86.21.575.701.46
Fax +86.21.575.701.44
[email protected]
Nice USA
San Antonio Texas USA
[email protected]
Nice Russia
Odintsovo Moscow Region Russia
Ph. +7.495.739.97.02
Fax +7.495.739.97.02
[email protected]
Nice South Africa
Johannesburg South Africa
[email protected]
Nice Polska
Pruszków Polska
Ph. +48.(022).759.40.00
Fax +48.(022).759.40.22
[email protected]
Nice Portugal
Mem Martins Portugal
Ph. +351.21.922.82.10
Fax +351.21.922.82.19
[email protected]
Nice Romania
Cluj Napoca Romania
Ph./Fax +40.(0)264.453.127
[email protected]
Nice Turkey
Kadikoy Istanbul Turkey
Ph. +90.216.456.34.97
Fax +90.216.455.78.29
[email protected]
Nice UK
Sutton in Ashfield
United Kingdom
Ph. +44.16.23.55.80.86
Fax +44.16.23.55.05.49
[email protected]
IST311.4858 – Rev. 00 – 21-09-2009
Headquarters
">