NTI ST-2FODP14-LC9 DisplayPort 1.4 Extender over Duplex Single-mode Fiber User Manual

ST-2FODP14-LC9

DisplayPort 1.4 Extender over Duplex Single-mode Fiber

User Manual

MAN404 REV 5/19/21

Introduction

The XTENDEX ® 8K DisplayPort 1.4 Extender via LC Fiber Optic Cable locates an Ultra-HD 8K 4320p 30Hz DisplayPort display away from a DP computer up to 3,937 feet (1,200 meters) via duplex LC single mode fiber optic cable. Each extender consists of a transmitter that connects to a DisplayPort source, and a receiver that connects to a DisplayPort display.



Signal transmission via two-strand single mode 9-micron LC fiber optic cable.



Supports Ultra-HD 8K resolutions to 7680x4320 @30Hz YUV 4:2:2, Ultra-HD 4Kx2K resolutions to 3840x2160 @60Hz

YUV 4:4:4, and HDTV resolutions to 1080p @144Hz.



DisplayPort features supported: o DisplayPort 1.4 o Multi-Stream Transport (MST) o Up to 36-bit Deep Color o LPCM o YCbCr 4:4:4, YCbCr 4:2:2, and RGB o HDR o Bandwidth up to 23.76Gbps



HDCP compliant



EDID pass-through for the support of any DisplayPort display device.



Cables can be installed in conduit prior to extender installation.



Supports Plug-n-Play specifications.



Low RFI/EMI for sensitive applications.

Cables



Use DP14-xx-MM to connect a DisplayPort source/display up to 15 feet from the transmitter/receiver. o Two 3-ft DisplayPort 1.4 cables (DP14-3-MM) included. o ST-2FODP14-LC9 only supports 8K@30Hz (4:2:2, 8-bit) and 4K@120Hz (4:2:2, 8-bit) resolutions (23.76Gbps) when used with NTI ’ s DP14-xx-MM cables. All other DP 1.4 cables will support resolutions to

3840x2160@60Hz ( 4:4:4, 8-bit ).



Use DP8K-FO-xxM-MMLC to connect a DisplayPort source/display up to 100 meters from the transmitter/receiver(not included). o Maximum resolution supported with ST-2FODP14-LC9 is 3840x2160@60Hz.



Use USB3C-DP4K-xx-MM to connect a computer, tablet, or smartphone with USB Type C connector up to 10 feet from the transmitter (not included).



Use DP-VGA-xx-MM to connect a VGA display up to 15 feet from the receiver (not included). o Supports resolutions to1920x1200@60Hz.



Use a duplex LC single mode 9/125-micron fiber optic cable to extend the receiver from the transmitter up to 3,637 feet

(1,200 meters) (not included).

Material Supplied with this kit:

ST-2FODP14-LC9 Local and Remote Unit

2- DP14-3-MM 3FT DisplayPort Male-to-Male cable

2- In:100 to 240V, 50/60Hz ; Out: DC 5V, 3A

2- Multi-country line cord

Note: DP14-x-MM cables are available from NTI in 3, 6, 10 and 15 foot lengths.

Features and Functions

Local Unit

1. LED Light (LINK LED)

Fiber link indicator. LED is solid BLUE when Source unit is linked to a Receiver.

2. Fiber Link Port

Duplex LC optical transceiver port. Extension link to

Duplex LC fiberoptic cable.

3. LED Light (Power LED)

5V Power indicator. LED is solid BLUE when DC is supplied to the Transmitter.

4. Power Jack

5VDC 3A Power supply connects here.

5. LED Light (Display/Monitor LED)

Display/Monitor connection indicator. LED is solid BLUE when display is connected to the Receiver.

6. LED Light (Source LED)

DisplayPort source connection indicator. LED is solid

BLUE when DisplayPort source is connected.

7. DP Source Port

DisplayPort cable connects between here and the host computer with

DisplayPort output port.

Remote Unit

1. LED Light (LINK LED)

Fiber link indicator. LED is solid BLUE when Receiver unit is linked to a Transmitter.

2. Fiber Link Port

Duplex LC optical transceiver port. Extension link to

Duplex LC fiberoptic cable.

3. LED Light (Power LED)

5V Power indicator. LED is solid BLUE when DC is supplied to the Receiver.

4. Power Jack

5VDC 3A Power supply connects here.

5. LED Light (Computer LED)

Computer connection indicator. LED is solid BLUE when computer(source) is connected to the Transmitter.

6. LED Light (Sink LED)

DisplayPort sink connection indicator. LED is solid

BLUE when DisplayPort monitor (sink) is connected.

7. DP Sink Port

DisplayPort cable connects between this port and the monitor with

DisplayPort input port.

Installation

This extender system is composed of two individual units, the Transmitter and the Receiver, interconnected by duplex singlemode fiber optic cable. Single-mode fiber optic Duplex cabling with LC connectors is required for extension up to 1.2km.

Note: The maximum possible extension distance depends on your host-side DisplayPort output.

Step 1. Connecting the Transmitter (Local Unit) to the Receiver (Remote Unit)

Connect the Transmitter and the Receiver unit using a duplex LC single-mode fiber optic cable.

Step 2. Installing the Receiver

1. Connect the supplied DP14-3-MM DisplayPort cable between the Receiver and your DisplayPort monitor input.

2. Connect the supplied power adapter to the Receiver.

Step 3. Installing the Transmitter

1. Place the Transmitter near the computer.

2. Connect another supplied DP14-3-MM DisplayPort cable between your host computer and the Transmitter.

3. Connect the supplied power adapt e r to the Transmitter.

Specifications

Extension Range (Point-to-point)

Maximum Resolution

Up to 1.2k

m over Duplex Single-mode Fiber

7680*4320@30Hz (YCbCr 4:2:2)

DPCP

HDR

Supported

Supported

DP Compliance DP 1.4

HDCP Compliant

Operating Temperature

Storage Temperature

Humidity

32 to 122°F (0 ˚ to 50 ˚ C )

-4 to 158°F (-20 ˚ to 70 ˚ C)

20-80% Operating, 10-90% Storage Relative

Humidity Non-Condensing

Power (Local and Remote) o Input: 100 to 240 VAC at 50 or 60Hz via AC adapter. o Output: 5VDC, 3A

2.95x5.63x1.15 in. (75x143x29 mm). Dimensions (Local and Remote)

WxDxH

Approvals CE, FCC, RoHS

Video Connector

Fiber Connector

Max. data rate

Power Consumption

Net Weight

Transmitter (Local Unit)

DisplayPort Female

Duplex LC x1

23.76Gbps

Receiver (Remote Unit)

DisplayPort Female

Duplex LC x1

23.76Gbps

5V/ 620 mA 5V/6 00 mA

2 66 g 2 63 g