Magic Leap PEQ Series Quick Start Manual

QUICK START GUIDE
EARLY ACCESS PROGRAM (PEQ SERIES) R EV. 3.16.2022
What’s in the Box
Your Magic Leap 2 Early Access Program (PEQ Series) box contains:
● Headset
● Compute Pack
● Controller
● Enterprise Charger or Health Care Charger, as applicable - 2 x
45W USB-C charger and cables for Compute Pack and Controller
● Fit Kit for Headset. A set of nose pads and forehead pads to
customize the fit
● Optional Overhead Strap to support in-motion use and slippage
● Frame with eye cups
● Shoulder strap for crossbody wearing
● Controller lanyard to attach to users wrist
● Carry Case and Cleaning Cloth, robust case to carry Headset,
Compute Pack and Controller
Pictured: Magic Leap 2 Headset, Compute Pack and Controller.
Attach Your Compute Pack to a Pocket…
Slide the Compute Pack onto a pocket until it moves past the clip.
Please don’t put the Compute Pack in a pouch or pocket while in use or
block the vents.
The Compute Pack easily clips onto your pocket.
… Or to the Shoulder Strap
Clip the carabiners on the Shoulder Strap to the corresponding
fasteners on the Compute Pack. Get comfortable by adjusting the
length.
Fasten the carabiners on the ends of the Shoulder Strap to the Compute Pack to
hold it into place.
Put on your Headset
Gently stretch the back of your Headset headband until it comfortably
fits over your head. Insert required pads and nosepiece from the
included Fit Kit for an individualized comfortable fit for you. For the best
comfort and visual experience, follow the steps outlined in the Fit and
Eye Calibration app accessible from the Home menu.
The Headset adjusts to the width of your head by gently stretching the temples of
the device.
Prevent Tangling the Cords
Be sure to prevent the cord from getting tangled or wrapped around the
headband.
The Headset cord should be clear of the headband accessory and torsion band.
Turn On Your Early Access Program (PEQ Series) Magic Leap
Press the button on the front of the Compute Pack and wait until the
lights are fully illuminated.
The five lights towards the top of the Compute Pack will be illuminated when fully
powered.
Identifying Buttons and Controls
Review the corresponding illustrations to become familiar with the
buttons and controls of your new Magic Leap 2.
Identify the buttons and controls on the Magic Leap 2 Controller Compute Pack
pictured.
Set Up Your Device
Your device needs to be set up before you can use it.
1. Your Controller should be paired out of the box. If not, connect the
Controller to the Compute Pack using the USB-C to USB-C cable.
2. Connect to WiFi using the Settings app.
a. Click on Network and internet.
b. Click on Wi-Fi.
c. Scroll through the list of WiFi using the touchpad and choose
your preferred network.
d. For secure networks, a virtual keyboard will popup: Enter your
password using the Controller.
e. Click “connect” on the WiFi screen.
Connect to WiFi through the Home > Setting > WiFi menu, pictured here.
Charge, Clean, and Store Safely
Charge
For the best experience, make sure the device is fully charged every
time you use it.
Clean
Make sure the device is turned off while cleaning. Remove the Forehead
Pad, Nose Pad, and Lens Insert. Use a damp, but not wet, isopropyl
alcohol wipe or sterile, lint-free cloth to gently clean the Headset,
Compute Pack, and Controller. Use a damp, sterile, lint-free cloth to
rinse and a dry one to finish.
Store
Safely store the device in the Carry Case or box provided.
Always keep it out of direct sunlight to avoid damage.
For the full safety instructions, see the Magic Leap 2 – PEQ Series
Safety Guide & Regulatory Information.
Keep up to date
We may update this guide from time to time. For the latest version,
please visit magicleap.com/start
Need more help?
Contact Customer Support by visiting our Early Access Program Customer
Care page.
Copyright © 2018 - 2022 Magic Leap, Inc.