GDC G-HUB Quick start manual

G-HUB Wireless Sensors &

Ethernet Gateway User’s Guide

G-HUB Ethernet Gateway Quick Start

Create a Monnit user account with assigned wireless gateways and sensors.

Attach the antenna to the antenna connector on the back panel of the Ethernet gateway

(make sure the connection is snug, but do not overtighten).

Plug an Ethernet cable with internet connectivity into the gateway

Plug the power supply into a power outlet then connect to the gateway.

Once all three lights turn green, your network is ready to bring sensors online.

www.gdcworld.com

1. Create a G-HUB User Account and Setup Sensor Network

If this is your first time using the iG-HUB online system site, you will need to create a new account. If you have already created an account you can skip to the “Logging into the

Online System” section. The following instructions will guide you through the account creation process.

1. In a web browser, navigate to https://www.G-HUB.com.

2. Click the “Get Started Here” button to create an account.

3. Follow the on-screen instructions to enter your account and contact

information.

4. After entering your account and contact information, you will be prompted to

create your first sensor network. Simply enter a name for this network.

5. Add the information from your G-HUBLink

™

gateway then click the “Assign Gateway”

button.

Contains FCC ID: ZTL-RFSC1 and IC: 9794A-RFSC1

This device complies with Part 15 of the

FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful

interference and

(2) this device must accept any interference

received, including interference that may

cause undesired operation.

ID: ######

Code: XXXXXX

6a. Add the information from your first G-HUB wireless sensor then click the

“Assign Sensor” button.

Peel

_

+

Back of Sensor

Contains: FCC ID: ZTL-RFSC1

IC: 9794A-RFSC1

Sensor ID: ######

Sensor Code: XXXXXX

6b. On the next screen, enter a name for the wireless sensor and use the

drop down to tell us how you are going to be using the wireless sensor.

(This allows us to suggest settings for your sensor.) When finished, click

the “Continue” button.

PAGE 2

7. Confirmation Screen.

When you have finished adding the sensor, you will see a confirmation screen. At this point you can assign notifications to the sensor (see Using The iG-HUB™ Online Wireless Sensor System) , assign additional sensors to your account or click “Done” to go to your sensors overview page.

2. Using the G-HUBLink

™

Ethernet Gateway

1. Understanding the Ethernet Gateway Lights

1 2 3

Front of Ethernet Gateway

Light 1 - Indicates the Ethernet cable is plugged in. A green light indicates ready and working, a red light indicates there is a problem.

Light 2 - Indicates the Ethernet has internet connectivity and can reach the online monitoring system. A green light indicates ready and working, a red light indicates there is a problem. A flashing green light indicates network traffic to the internet.

Light 3 - Indicates sensor network activity. A green light indicates ready and working, a red light indicates there is a problem. A flashing green light indicates radio traffic from the sensors.

For help troubleshooting Ethernet gateway lights view: http://www.G-HUB.com/support/hardware/gateways/ethernet/troubleshooting-a-G-

HUBlink-ethernet-gateway

2. Ethernet Gateway Controls

Back Panel

Power Plug

Control Button

Ethernet Port RP SMA Antenna Connector

Using the Control Button:

1) A short press will trigger the gateway to immediately send all stored sensor messages to the online system and download any pending system messages to deliver to the sensors. (The default heartbeat for the Ethernet gateway is 5 minutes.)

2) Press and hold to reset the gateway to factory settings. Factory settings will be reset to defaults, including the heartbeat setting of 5 minutes on both the gateway and in the online system. DHCP, server addressing and port are all restored to default settings, for example. You will need to login to the online system after resetting the gateway to reconfigure the gateway to your desired settings.

Note: If your gateway powers up with the lights scrolling from left to right, it has entered into boot loader mode accidentally. Make sure the button is free from obstruction and reboot the gateway by removing the power plug, waiting for 10 seconds then reinserting the power plu g.

PAGE 3

3. Configuring The Ethernet Gateway

The Ethernet Gateway collects data from all sensors within range and is preconfigured to batch deliver the sensor messages to the online system every 5 minutes.

The Ethernet Gateway uses DHCP (Dynamic Host Configuration Protocol) to automatically acquire a network address from the LAN (Local Area Network). In the event that it needs to have an address manually assigned to it, you can assign an IP address as well as a gateway mask and default DNS through the online interface. For more information on configuring the G-HUB Ethernet Gateway please view the support documentation at http://www.G-HUB.com/pdf/Ethernet_Gateway_Configuration.pdf.

Note: This advanced configuration is NOT required in most instances. In the event that it is required, you can initialize the gateway on a network that uses the default DHCP settings, or you can follow the instructions for changing the configuration settings on a PC, which are included later in this User’s

Guide.

Upon logging into the online system as an administrator, select “My Account” then choose the edit icon next to your sensor network. From there you can alter the heartbeat of the Ethernet Gateway as well as edit any other configurations available. There is also a quick link to reset all gateway settings to factory defaults.

3. Using Your G-HUB Wireless Sensors

Insert Batteries Into Wireless Sensors

Important: Make sure your sensors are at least 3ft. away from Ethernet Gateway.

Peel back the black sticker cover of the battery slot and slide the coin cell battery into the sensor as shown in fig.1. It will power on within 10-20 seconds. Once online, your sensor is ready to be deployed. If you wish to change a sensor configuration, change the parameter in the software. The new parameters will be transmitted to the sensor on the next heartbeat. If you need a more immediate response from the sensor, power cycle the sensor by removing, then re-inserting the battery.

Notes:

- If the sensor status indicator does not change, reset

the sensor by removing the battery.

- Wait 60 seconds then re-insert the battery.

- When inserting the battery, make sure to push the

battery all the way back using a paper clip.

Battery

Insertion fig.1

- Note the proper orientation of battery in fig.1

Warning: Your sensors ship with a 2 hour heartbeat.

It is recommended that unless you are using the AA battery

_

+ solution, you should set the heartbeat to no faster than one hour to preserve battery life. When changing a sensor’s heartbeat, the new configuration information will be sent to the sensor on it’s next heartbeat. If you want to update the sensors immediately you can reset them manually.

Manual Sensor Reset Process:

1 - Using the end of a paper clip, push the batteries out of the sensors through the small hole

in the top of the sensor

2 - Change the sensor heartbeat through the online system

3 - Re-insert the batteries into the sensors

PAGE 4

4. Using The iG-HUB

™

Online Wireless Sensor System

1. Understanding The Online Interface

When you log into the online system, the default view shows all of your sensors last recorded data.

Menu System View / Sort Features

Date Range Selector

Sensors Overview Sensor Details View

Menu System

Overview

Notifications

- Shows all sensors in the account and their last readings.

- Manage sensor notifications and show all sent notifications.

Manage

Reports

- Manage networks, sensors and gateways.

- Printable account and sensor network reports.

Sensor Maps - Visual maps to help you track sensor placement.

Support - Support information for using sensors and software.

View / Sort Features

This section allows you to sort the sensors being viewed and search for sensors on your account.

Sensor Overview

Displays sensors on your account with their last reading and status information. Clicking on a sensor row expands the “Sensor Detail View” allowing you to view detailed information for the selected sensor.

PAGE 5

To the left side of each sensor row is an indicator to help you understand the current status of the sensor.

Sensor is checking in and within user defined safe parameters.

Sensor has met or exceeded a user defined threshold or triggered event.

Sensor has not checked in (inactivity alert sent).

No sensor readings will be recorded (Inactive)

Sensor Details View

Clicking on a sensor row on the “Overview” page expands the row to include a detailed sensor view for the selected sensor.

Select a tab to change between:

History - Displays a history of the selected sensor’s data.

Chart - Displays a graphical view of the selected sensor’s data.

Notifications - Allows you to manage notifications for the sensor.

Export - Allows you to archive data by exporting as a .csv file.

Edit - Allows you to manage sensor settings.

Calibrate - Available on certain sensor types to provide more accurate data.

Note: The data shown on the chart, notification, history and export tabs is based on the date range indicated on the upper right side of the sensor detail information. To change the date range, click inside the date box.

2. History and Chart Views.

Clicking on the “History” or “Chart” tabs within the sensor detail panel allows you to view the sensor’s data history as time stamped data or in a graphical chart format.

3. Configuring Sensor Settings

To edit a sensors operation settings, click on the sensor overview row to display the details view. Click on the “Edit” tab to access the sensor configuration panel.

The sensor edit panel allows you to set the primary configurations for the sensor. Mousing over the question mark icon by each setting will provide an explanation of that setting. When you have finished making changes, press the “Save” button at the bottom of this section.

Note: Be sure to click the “Save” button anytime you make a change to any of the sensor parameters.

All changes made to the sensor settings will be downloaded to the sensor on the next sensor heartbeat

(check-in). Once a change has been made and “Saved,” you will not be able to edit that sensor’s configurations again until the sensor has downloaded the new setting.

PAGE 6

Note: To change the date range of the viewable information, click on the date range box at the top right of the sensor detail panel.

PAGE 7

4. Sensor and/or Gateway Notification(s).

Notifications for a single sensor can be created, deleted or edited by clicking the

“Notifications” tab in a sensor’s detail view.

• Advanced Notifications - Allows the user to set notifications based on advanced rules, such as comparing past data points with the current one to determine if a notification should be sent.

• Existing Notifications - Use notifications that have already been created on your account with the selected sensor.

Notification Settings

This area allows the user to set notification parameters such as naming the notification, customizing the notification message and setting sensor conditions that will trigger the notification.

People to Notify

The list on the left shows all available users on the account. You can type into the search box to filter large lists of users. Select the user(s) to receive the notification and click the arrow button to add them to the recipient list. By default, email notifications are activated.

Clicking the notification delivery method icon toggles them on and off (green is on, grey is off). If the user should receive text message notifications, click on the phone icon to turn it green.

Notifications can be created, deleted or edited for any sensor or group of sensors by clicking on “Notifications” in the main menu.

Create a New

Notification

Toggle On/Off Click to Open Detail View Send Test Edit Delete

When creating a notification, you will need to select the type of notification to create.

• Sensor Reading Notification - Reading notifications are sensor specific (i.e. water sensor = trigger alert when water present, temp sensor = trigger alert when temp is above

70F, etc.). When creating a sensor reading notification, you will need to choose the sensor type you are creating the alert for. The select box will only show sensor types that are currently being used on your sensor network.

• Battery Notification - Allows users to define a battery power percentage level that will trigger an alert from the system, warning them to replace batteries.

PAGE 8

• Inactivity Notification - Set-up “Inactivity” notifications to alert you when your sensors have stopped communicating with the servers. Failure to set up an “Inactivity” notification will result in no email/SMS text being sent should your sensors stop communicating with the servers.

Sent From

Allows you to assign devices (sensors and gateways) that will cause the notification to be sent. When a notification is sent from the system, it will automatically include the device name and the data that caused the notification to be sent. A single notification can be assigned to multiple sensors or gateways. Sensor reading notifications can only be assigned to sensors of the same type. General notifications such as “battery status”, can be assigned to any or all sensors.

PAGE 9

Devices to Notify

If you have a G-HUB Control or Notifier A/V device on your network, you will also see a “Devices to Notify” tab. This will allow the notification to interact with these types of devices. Select a device from the list on the left and click the arrow button to add it to the recipient list. Clicking the control icon toggles their setting.

Certain wireless sensors can be calibrated for more accurate readings (ex. temperature sensors). If calibration is possible for a sensor, the “Calibrate” tab will be visible in the detail view. To calibrate a sensor, replace the last reading with the more accurate reading and click

“Calibrate”. All future readings from the sensor will be based off the new calibration setting.

Note: Control devices have two relays per device that are controlled separately. You can turn a relay on, off or toggle the state. You can also set a duration by clicking on the timer icon. This will perform the selected toggle (on/off/toggle) for a set duration, then change back.

5. Exporting Sensor Data

Clicking on the “Export” tab within the sensor data window allows you to export sensor data to a comma separated value (.csv) file or send the sensor data to an external web source.

To export sensor data you must first select the date range for the data you want to export.

Once the date range is selected, determine whether you want sensor data from the selected sensor only, from all sensors in the network or all sensors assigned to the account.

When you are finished, click on “Export Data” at the bottom of this window. The data will be exported to a comma separated value (.csv) file format.

Note: Only the first 2,500 records within the selected date range will be exported.

You can alternately send your sensors’ incoming data to a 3rd party by clicking on the “Configure data push” button at the bottom of the window. From this area you can pass data from your wireless sensor network devices to another service in real time. This is done by coding the data into a url query then sending the data via http get request at the time data is received.

There is an extensive list of parameters that can be passed, as listed in the viewed window, that allow you to send detailed information about both the data and the sensor.

6. Calibrating Sensor Data

PAGE 10

7. Manage Sensor Networks

To view or edit information about your wireless sensor network(s), click on “Manage” in the main navigation. This area allows you to edit network details, create new sensor networks, and manage wireless gateways and sensors for your network(s).

Click to

Manage

Create a new network

Select which network to view

Edit network information

Clear sensor history and data

Add a device to the network

Remove device from network

Note: Some buttons and features are only visible if there is more than one sensor network setup on the account, such as the network selection box in the upper right corner.

If more than one sensor network is setup on the account, you can easily move gateways and sensors from one network to another by clicking on the “Move Device” button at the far right of the device’s “Status” section.

If you clear a sensor’s data, the data history is deleted from the entire system and can not be recovered. We recommend exporting a sensor’s data history using the export function in the sensor details view

(“Overview” page) before clearing the sensor’s data if you want to have a record of the data.

PAGE 11

5. Advanced Settings and Interfacing with the G-HUB Ethernet

Gateway Through iG-HUB.

1. Ethernet Gateway Edit Screen

When you log into the online system, the default view shows all of your sensors last recorded data.

To set the Static IP, uncheck the Use DHCP box and fill in the settings:

The force transmit on Aware box tells the gateway to deliver immediately the messages marked as Aware from the sensors. If this box is unchecked and the setting is saved, then the gateway only dumps the sensor messages it has been collecting on the Heartbeat Interval. This allows for controlled communication when sporadic communication from the gateway is either unacceptable or not ideal.

2. External Interfaces:

Data collected by the Ethernet Gateway from the sensors in the network can be accessed when these interfaces are turned on. Multiple interfaces can be active at the same time.

All interfaces require that the Ethernet gateway be set to a Static IP address. (By default, the unit uses DHCP).

Real Time TCP Interface

Poll on the gateway’s assigned port to retrieve gateway and sensor data.

The name can be edited to whatever you prefer.

The gateway type should NOT be edited, unless you are directed to do so by a G-HUB

Support Representative.

The unit’s MAC Address is viewable here, should you need to access it.

The heartbeat dictates how often the gateway communicates with the server. This is both for communication passed up to the server from the gateway and the communication passed to the gateway from the server. Exceptions to this interval include Aware messages from sensors.

The Enterprise Server Host address and Communication Port will always be one of G-

HUB’s servers and ports by default, but should you require that the gateway be pointed to your private servers, the gateway can be configured to do so. Make sure to set the appropriate port as well, if port 3000 will not be used.

Mark the interface active and Save. The default port is 3500, but can be edited.

PAGE 12 PAGE 13

MODBUS TCP Interface

Use MODBUS TCP software to pull in gateway and sensor data. G-HUB provides a register map. Check the box to make the interface Active and Save.

Data 1

Data 2

Data 3

Data 4

Data 5

Data 6

Data 7

Data 8

Sensor Data Field 1

Sensor Data Field 2

Sensor Data Field 3

Sensor Data Field 4

Sensor Data Field 5

Sensor Data Field 6

Sensor Data Field 7

Sensor Data Field 8

40109

40110

40111

40112

40113

40114

40115

40116

108

109

110

111

112

113

114

115

SNMP Poll and Trap Interface

Use SNMP software to pull in gateway and sensor data. G-HUB provides a .MIB file.

There are four available interfaces. Set the SNMP Interface Address for each one the address of the device sending the SNMP request). Mark the interface Active and Save.

The MODBUS TCP Interface will store all data values in 16-bit registers. The registers and their data fields are mapped below:

PAGE 14

Field Description

GATEWAY

Gateway ID_High The first 16 bytes of a 32 byte serial ID number

REGISTERS Gateway ID_Low The last 16 bytes of a 32 bytes serial ID number

SENSOR

Gateway Version

Gateway Device

Count

Sensor ID_High

The version of gateway firmware on the device

The number of devices

(sensors & gateways) in its network

The first 16 bytes of a 32 byte serial ID number

REGISTERS

Sensor ID_Low The last 16 bytes of a 32 bytes serial ID number

Device Type The unique type identifier for the sensor profile

Data Age

Is Device Active

Is Aware

Voltage

The number of seconds that have elapsed since the last data was retrieved

0 indicates no data for this slot

Becomes aware when a sensor threshold has been breached

Battery voltage

RSSI Signal Strength indicator

0-100%

Register Data

Address

40001 0

40002

40003

40004

40101

40102

40103

40104

40105

40106

40107

40108

1

2

3

100

101

102

103

104

105

106

107

The MIB file is available through here: resources.G-HUB.com/content/downloads/G-HUBEGW-MIB_v1

The MIB Tree looks like this:

PAGE 15

Ethernet Gateway MIB tree with a short description of each field:

EGW Data

*GW Section

*GW Serial

*Version

*WD Count

*WNetSection

*WD Entry

*Index

*Serial

*Type

*Age

*Active

*Alarming

*Voltage

*RFSignal

*Data1

*Data2

*Data3

*Data4

*Data5

*Data6

*Data7

*Data8

Description

Gateway Section

Gateway Serial ID

Gateway Firmware Version

Wireless Device Count

Wireless Network Seciont

Wireless Device Entry

Index Number

Wireless Device Serial ID

Device Type (eg temp, water, motion sensor, etc)

Number of seconds since last data recording

Indicates if the wireless device is reporting in as expected

Indicates if the wireless device has detected data that is urgent or breaches a threshold

Battery voltage recorded at the time of data reading

Signal Strength recorded on data reading delivery

Data recorded by wireless device (eg temperature, water detected, motion detected, etc)

Data recorded by wireless device (eg temperature, water detected, motion detected, etc)

Data recorded by wireless device (eg temperature, water detected, motion detected, etc)

Data recorded by wireless device (eg temperature, water detected, motion detected, etc)

Data recorded by wireless device (eg temperature, water detected, motion detected, etc)

Data recorded by wireless device (eg temperature, water detected, motion detected, etc)

Data recorded by wireless device (eg temperature, water detected, motion detected, etc)

Data recorded by wireless device (eg temperature, water detected, motion detected, etc)

PAGE 16

6. Setting up the Ethernet gateway for use with iG-HUB Express

iG-HUB Express (PC Software) Setup

Visit http://www.G-HUB.com/support/downloads/ to download and install the iG-HUB

Express software.

• Launch the iG-HUB Express installer and follow the on-screen instructions.

• Launch the iG-HUB Express program.

• Activate the Express software with the code you received when purchasing.

• Add the gateway(s) and wireless sensors to the software.

Contains FCC ID: ZTL-RFSC1 and IC: 9794A-RFSC1

This device complies with Part 15 of the

FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful

interference and

(2) this device must accept any interference

received, including interference that may

cause undesired operation.

ID: ######

Code: XXXXXX

• Verify that the gateway was added successfully by checking the Gateways list.

PAGE 17

• Click on “About”, then “Local IP Addresses” and make note of the IP address that your computer is using on your network.

• Connect the Ethernet Gateway directly to the Ethernet port of your PC using a standard

Ethernet cable. Confirm that the PC has no other internet connection (turn off Wi-Fi).

Confirm the PC firewall does not prohibit an inbound connection. Plug power cable into the Ethernet gateway.

• Plug in the power cable.

• While the device is booting, press and hold the Reset Button on the back of the gateway.

The button must be held in the down position by the time the third green light illuminates, or else another attempt will need to be made. When the device finishes booting, all three lights will toggle red, green. Release the button and the device is in local configuration mode. Do not hold the Reset button for more than four seconds (that will factory reset the device).

The lights will flash green once every other second while the device attempts to resolve

Ethernet Link State. The lights will flash green once every second while the device attempts to resolve IP addresses with the host PC. Finally, the lights will flash green twice every second when device is waiting for valid web traffic.

• Once the PC has setup the direct network, use a web browser (e.g. Chrome) and go to

“192.168.100.1”. The Ethernet gateway Setup screen should now be displayed.

Note: The lights will all turn solid green once this connection has been established.

• Click on the “Data Interfaces” tab.

• Under “Default Server Configuration” enter the IP address that you noted from the iG-HUB

Express software into the primary and secondary server [URL/IP] boxes, and use 3000 as the default communication port, then click “Save Changes”.

• When finished, click the “Reboot” button on the top right side of the page to restart the gateway.

• When the lights begin flashing on the gateway, you can unplug the power to the gateway and disconnect it from the computer.

• Reactivate the Wi-Fi or other Internet connection for the computer, so it can connect to the network.

• Plug your Ethernet gateway into your Internet router and power up the Ethernet gateway. All three lights should go green now, and your gateway should report into G-

HUB Express.

If it does not, check that the PC has the internet connection turned on, recheck your IP

Address, power up your gateway and make sure the gateway is added into G-HUB

Express. (If you left your secondary set to point to sensorsgateway.com (which is iG-HUB) and the lights on your gateway are green, check iG-HUB to see if the gateway is reporting in there. If so, power cycle the gateway and try again.)

PAGE 18 PAGE 19

Error Reporting, Troubleshooting and Support

For technical support and troubleshooting tips please visit our support library online at http://www.G-HUB.com/support/ . If you are unable to solve your issue using our online support, email G-HUB support at [email protected]

with your contact information and a description of the problem, and a support representative will call you within one business day.

For error reporting, please email a full description of the error to [email protected]

.

Warranty Information

(a) G-HUB warrants that G-HUB-branded products will be free from defects in materials and workmanship for a period of one (1) year from the date of delivery with respect to hardware and will materially conform to their published specifications for a period of one (1) year with respect to software. G-HUB may resell sensors manufactured by other entities and are subject to their individual warranties; G-HUB will not enhance or extend those warranties.

G-HUB does not warrant that the software or any portion thereof is error free. G-HUB will have no warranty obligation with respect to Products subjected to abuse, misuse, negligence or accident. If any software or firmware incorporated in any Product fails to conform to the warranty set forth in this Section, G-HUB shall provide a bug fix or software patch correcting such non-conformance within a reasonable period after G-HUB receives from

Customer (i) notice of such non-conformance, and (ii) sufficient information regarding such non-conformance so as to permit G-HUB to create such bug fix or software patch. If any hardware component of any Product fails to conform to the warranty in this Section, G-HUB shall, at its option, refund the purchase price less any discounts, or repair or replace nonconforming Products with conforming Products or Products having substantially identical form, fit, and function and deliver the repaired or replacement Product to a carrier for land shipment to customer within a reasonable period after G-HUB receives from Customer (i) notice of such non-conformance, and (ii) the non-conforming Product provided; however, if, in its opinion, G-HUB cannot repair or replace on commercially reasonable terms it may choose to refund the purchase price. Repair parts and replacement products may be reconditioned or new. All replacement products and parts become the property of G-HUB.

Repaired or replacement products shall be subject to the warranty, if any remains, originally applicable to the product repaired or replaced. Customer must obtain from G-HUB a Return

Material Authorization Number (RMA) prior to returning any Products to G-HUB. Products returned under this Warranty must be unmodified.

Customer may return all Products for repair or replacement due to defects in original materials and workmanship if G-HUB is notified within ninety (90) days of customer’s receipt of the product. G-HUB reserves the right to repair or replace products at its own and complete discretion. Customer must obtain from G-HUB a Return Material Authorization Number

(RMA) prior to returning any products to G-HUB. Products returned under this Warranty must be unmodified and in original packaging. G-HUB reserves the right to refuse warranty repairs or replacements for any products that are damaged or not in original form. For products outside the ninety-day warranty period repair services are available at G-HUB at standard labor rates for a period of one year from the Customer’s original date of receipt.

PAGE 20

(b) As a condition to G-HUB’s obligations under the immediately preceding paragraphs,

Customer shall return Products to be examined and replaced to G-HUB’s facilities, in shipping cartons which clearly display a valid RMA number provided by G-HUB. Customer acknowledges that replacement products may be repaired, refurbished or tested and found to be complying. Customer shall bear the risk of loss for such return shipment and shall bear all shipping costs. G-HUB shall deliver replacements for Products determined by G-HUB to be properly returned, shall bear the risk of loss and such costs of shipment of repaired products or replacements, and shall credit Customer’s reasonable costs of shipping such returned Products against future purchases.

(c) G-HUB’s sole obligation under the warranty described or set forth here shall be to repair or replace non-conforming products as set forth in the immediately preceding paragraph, or to refund the documented purchase price for non-conforming Products to Customer. G-

HUB’s warranty obligations shall run solely to Customer, and G-HUB shall have no obligation to customers of Customer or other users of the Products.

Limitation of Warranty and Remedies.

THE WARRANTY SET FORTH HEREIN IS THE ONLY WARRANTY APPLICABLE TO

PRODUCTS PURCHASED BY CUSTOMER. ALL OTHER WARRANTIES, EXPRESS

OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY

DISCLAIMED. G-HUB’S LIABIITY WHETHER IN CONTRACT, IN TORT, UNDER ANY

WARRANTY, IN NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE PURCHASE

PRICE PAID BY CUSTOMER FOR THE PRODUCT. UNDER NO CIRCUMSTANCES

SHALL G-HUB BE LIABLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL DAM-

AGES. THE PRICE STATED FOR THE PRODUCTS IS A CONSIDERATION IN LIMITING

G-HUB’S LIABILITY. NO ACTION, REGARDLESS OF FORM, ARISING OUT OF THIS

AGREEMENT MAY BE BROUGHT BY CUSTOMER MORE THAN ONE YEAR AFTER

THE CAUSE OF ACTION HAS ACCRUED.

IN ADDITION TO THE WARRANTIES DISCLAIMED ABOVE, G-HUB SPECIFICALLY DIS-

CLAIMS ANY AND ALL LIABILITY AND WARRANTIES, IMPLIED OR EXPRESSED, FOR

USES REQUIRING FAIL-SAFE PERFORMANCE IN WHICH FAILURE OF A PRODUCT

COULD LEAD TO DEATH, SERIOUS PERSONAL INJURY, OR SEVERE PHYSICAL OR

ENVIRONMENTAL DAMAGE SUCH AS, BUT NOT LIMITED TO, LIFE SUPPORT OR

MEDICAL DEVICES OR NUCLEAR APPLICATIONS. PRODUCTS ARE NOT DESIGNED

FOR AND SHOULD NOT BE USED IN ANY OF THESE APPLICATIONS.

PAGE 21

Certifications

United States FCC

This equipment has been tested and found to comply with the limits for a Class B digital devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications not expressly approved by G-HUB could void

the user’s authority to operate the equipment.

RF Exposure

WARNING:

To satisfy FCC RF exposure requirements for mobile transmitting devices, the antenna used for this transmitter must not be co-located in conjunction with any other antenna or transmitter.

G-HUB Wireless Sensors and Ethernet Gateway Contain: FCC ID: ZTL-RFSC1

This device has been designed to operate with an approved antenna listed below, and having a maximum gain of 5.1 dBi. Antennas not included in this list or having a gain greater than 5.1 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms.

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication.

Approved Antennas

The following antennas are approved for use with G-HUB devices.

• Hyperlink HG905RD-RSP (5.1 dBi Rubber Duck)

• Pulse W1063 (3.0 dBi Rubber Duck)

• ChangHong GSM-09 (2.0 dBi Rubber Duck)

• Specialized Manufacturing MC-ANT-20/4.0C (4” whip)

PAGE 22

Canada (IC)

English

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry

Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

The radio transmitter (IC: 9794A-RFSC1) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

French

Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.

Le présent émetteur radio (IC: 9794A-RFSC1) a été approuvé par Industrie Canada pour fonctionner avec les types d’antenne énumérés ci-dessous et ayant un gain admissible maximal et l’impédance requise pour chaque type d’antenne. Les types d’antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitation de l’émetteur.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, méme si le brouillage est susceptible d’en compromettre le fonctionnement.

Industry

Canada

PAGE 23

Additional Information and Support

For additional information or more detailed instructions on how to use your

G-HUB Wireless Sensors or the iG-HUB Online System, please visit us on the web at http://www.G-HUB.com/support/ .

Global Design Corporation Inc

67 East Park Place Suite 750, Morristown NJ 07960, United States

O 973 437 4329, F 973 206 2288, [email protected], www.gdcworld.com