Owner’s Manual
InVision Element Table™
37128
Important
Before using this product:
• Read this manual
• Comply with all safety and operating instructions
• Ensure all parts and correct quantities are included
Any parts damaged during shipment must be reported
within 5 days of receipt. To report information regarding
missing parts or damage, to purchase parts or accessories, or if you have any questions, please contact us.
Thank you for purchasing Spectrum products!
Spectrum Industries, Inc
925 First Avenue, Chippewa Falls, WI 54729 USA
800 235 1262
715 723 6750
www.spectrumfurniture.com
0118729R2 Page 1 of 11
Important Safety and Care Instructions
• Read this owner’s manual before assembly or operation.
• Do not allow children to move the table.
• For indoor use only. Do not install or store the table where it will be
exposed to moisture.
• Do not block the ventilation openings.
• Do not allow anyone to sit, stand, or climb on the table.
• Use a damp, soft-cloth, or sponge, with mild soap or detergent solution
to clean dirty surfaces. Do not use harsh solvents or abrasives.
• This table is intended for institutional use. It does not have any userserviceable parts or user-maintenance requirements. If servicing is
necessary, please contact Spectrum Industries for assistance.
Warning - Relocating audio and/or video equipment to furniture not specifically
designed to support audio and/or video equipment may result in death or
serious injury due to the furnishing collapsing or over turning onto a child.
Warning - Death or serious injury may occur when children climb
on audio and/or video equipment furniture. A remote control or toys
placed on the furnishing may encourage a child to climb on the
furnishing and as a result the furnishing may tip over on to the child.
General Electrical Safety:
• Keep power switches in the OFF position before plugging or
unplugging from the wall outlet.
• Be sure total device / equipment load does not exceed 12-amps.
• Do not plug power cords into an extension cord.
• Inspect power cords for damage before each use. Do not use cords
that are damaged.
• Unplug power cord from electrical outlet by gripping the cord-do not
unplug by pulling only on the cord.
• Do not step on, drive over, drag, or place objects on power cords.
• For added safety, plug into a grounded outlet controlled by a GFI
(Ground Fault Interrupter) circuit breaker.
• Damaged electrical components can create significant hazards to
users and is not covered by the warranty. Repairs should always be
performed by a qualified electrician.
• Electrical devices are not toys. Children are often unaware of the
hazards associated with electrical devices. This table must always
be used by adults or with adult supervision.
0118729R2 Page 2 of 11
Components
Standard Worksurface
60”L x 42”W worksurface
72”L x 42”W worksurface
96”L x 42”W worksurface
• Blank
0118512
0118518
0118549
0118513
0118519
0118550
0118514
0118520
0118551
0118515
0118521
0118552
0118516
0118522
0118553
0118517
0118548
0118554
• 1 Cove cutout
• 2 Cove cutouts
• Display Stand
cutout
• 1 Cove cutout
• Display Stand
cutout
• 2 Cove cutouts
• Display Stand
cutout
Note: One worksurface is included. The above information only applies to standard worksurfaces (without custom cutouts) only.
0118729R2 Page 3 of 11
T-Leg Components
Corner Post Components
(See p.5 for assembly)
(See p.6 for assembly)
(2) T-Leg assembly
0118384 - 27”H
0118385 - 30”H
0118386 - 42”H
(4) 037779
5/16-18 Glide
(4) 037779
5/16-18 Glide
(20) 026064
1/4-20 x 5/8”
PHMS
(44) 026064
1/4-20 x 5/8”
PHMS
(20) 0100167
8-32 x 1/2” PH
Thread-cutting
screw
(2) 0100167
8-32 x 1/2” PH
Thread-cutting
screw
(4) Post Leg assembly
0118387 - 27”H
0118388 - 30”H
(8) 041289
1/4-20 x 1-3/4”
PHMS
Wire Tray Components
AV Equipment Channel Components
(See p.5 for assembly)
(See p.8 for assembly)
(1) Tray-left
(1) Tray-right
(2) Side Panel
0118478 - 60”L Element
0118639 - 72”L Element
0118641 - 96”L Element
0118477 - 60”L Element
0118638 - 72”L Element
0118640 - 96”L Element
0119837 - 60”L Element
0119574 - 72”L Element
0119600 - 96”L Element
(1) 0119571
Front upright
(1) 0119572
Rear upright
(1) 0118483
End Cap
(2) 0100167
8-32 x 1/2” PH
thread-cutting screw
(1) Lower Channel
0119863 - 60”L Element
0119584 - 72”L Element
0119601 - 96”L Element
026064
1/4-20 x 5/8” PHMS
(20) - 60”L Element
(16) - 72”L Element
(12) - 96”L Element
(3) 059984
2” Snap-in
Grommet
(12) 052605
1/4-20 x 15mm
JC bolt
0118729R2 Page 4 of 11
Table with T-Legs and Wire Tray
Assembly / Setup
1. Attach T-Legs to worksurface
Glide
1. Place the worksurface upside-down (laminate side-down) onto a flat,
non-abrasive surface like another table. Figure A1.
2. Attach the two T-legs as shown with 1/4-20 x 1-3/4” PHM screws.
Make sure the holes on the vertical leg tubes face inward.
3. Install the four glides.
T-leg
Phillips
screwdriver
Tools Required
A
or
Cordless drill with
Phillips driver
(best)
These holes
face inward
Note: Start all screws by hand
to prevent cross-threading.
1/4-20 x 1-3/4” PHMS
(4 per)
Worksurface
Figure A1
1. Attach the left and right wire tray to the worksurface as shown
with 1/4-20 x 5/8” PHM screws. Figure A2.
2. Install the end cap with (2) 1/4-20 x 5/8” PHMS, and (2) 8-32 x
1/2” PH thread-cutting screws and tighten securely.
Note: Do not install the end cap if any power modules or
devices will be installed in worksurface cutouts later. This
will provide easier access during module installation.
One of the wire trays can also be left off to provide access.
Phillips
screwdriver
Tools Required
2. Attach Wire Tray to worksurface
or
Cordless drill with
Phillips driver
(best)
These holes
face inward
Wire Tray-right
Wire Tray-left
(2) 8-32 x 1/2”
PH thread-cutting
screws
1/4-20 x 5/8” PHMS
(multiple required)
End cap
(2) 1/4-20 x
5/8” PHMS
Figure A2
(When complete, proceed to p.7)
0118729R2 Page 5 of 11
B Table with Post Legs and Wire Tray
1. Place the worksurface upside-down (laminate side-down) onto a
flat, non-abrasive surface like another table. Figure B1.
2. Attach each post leg as shown with (8) 1/4-20 x 5/8” PHM screws.
3. Install the four glides.
Note: Start all screws by hand
to prevent cross-threading.
Glide
Tools Required
1. Attach Post legs to worksurface
Assembly / Setup
Post leg
Phillips
screwdriver
or
Cordless drill with
Phillips driver
(best)
1/4-20 x 5/8” PHMS
(8 per)
Worksurface
Figure B1
Tools Required
2. Attach Wire Tray to worksurface
1. Attach the left and right wire tray to the worksurface as
shown with 1/4-20 x 5/8” PHM screws. Figure B2.
2. Install the end cap with (2) 1/4-20 x 5/8” PHMS, and (2)
8-32 x 1/2” PH thread-cutting screws and tighten securely.
Note: Do not install the end cap if any power modules or
devices will be installed in worksurface cutouts later. This
will provide easier access during module installation.
One of the wire trays can also be left off to provide access.
Wire
Tray
-right
Phillips
screwdriver
or
Cordless drill with
Phillips driver
(best)
Wire
Tray
-left
(2) 8-32 x 1/2”
PH thread-cutting
screws
End cap
(2) 1/4-20 x
5/8” PHMS
Figure B2
(When complete, proceed to p.7)
0118729R2 Page 6 of 11
3. Flip Table upright
1. Carefully flip the table upright-this will take 3-4 people. Figure 3.
2. If necessary, adjust glides to level table.
CAUTION
Do not allow the legs to contact the floor until
the table is completely rotated. Side-loading
of the table legs could cause damage.
Figure 3
Optional
Display
Stand
4. Power Modules and Wiring
1. If your worksurface has cutouts for optional power modules or other
components, install the devices then route and secure the cords
using the cord channel underneath. Figure 4.
2. If removed, install any remaining cord channels to the worksurface
with 1/4-20 x 5/8” PHM screws.
3. If removed, install the end cap with (2) 1/4-20 x 5/8” PHMS, and (2)
8-32 x 1/2” PH thread-cutting screws and tighten securely.
Figure A2, Figure B2.
Cord Channel
Optional Power
module
End cap
Wiring
channel
Figure 4
0118729R2 Page 7 of 11
Assembly / Setup
1. Assemble AV Equipment Channel
1. Attach the front and rear uprights to the lower channel with
1/4-20 x 5/8” PHM screws. (10 per upright). Figure C1.
2. Tighten securely.
3. Install the (3) 2” snap-in grommets.
1/4-20 x 5/8” PHMS
(8 per)
Rear Upright
(with grommet hole)
Tools Required
C Table with T-Legs and AV Equipment Channel
Phillips
screwdriver
or
Cordless drill with
Phillips driver
(best)
2” Snap-in
grommet
Front
Upright
2” Snap-in
grommet
Lower
Channel
Note: Start all screws by hand
to prevent cross-threading.
Figure C1
2” Snap-in
grommet
Tools
Required
2. Attach T-Legs to AV Equipment Channel
1. Install glides onto T-legs. Figure C2-1.
2. Attach each T-leg to the AV equipment channel with (6) 1/4-20
x 15mm JC Bolts and tighten securely. Figure C2-2.
3. Flip the entire assembly upright. (Glides down).
4mm Hex
wrench
AV Equipment
Channel
Glide
(6) 1/4-20 x
15mm JC bolts
T-leg
T-leg
Figure C2.1
Figure C2.2
0118729R2 Page 8 of 11
1.
2.
3.
4.
5.
6.
Tools Required
3. Attach Worksurface
Move leg assembly into the final location in the room.
Set the worksurface onto the assembled legs and align mounting holes. Figure C3.1.
Install (4) 1/4-20 x 40mm JC bolts through each leg to secure the worksurface. Figure C3.2.
Install (4) 1/4-20 x 5/8” PHM screws through each upright to secure the worksurface.
Tighten all screws securely.
If necessary, adjust glides to level table.
Note: Start all screws by hand
to prevent cross-threading.
Phillips
screwdriver
or
Cordless drill with
Phillips driver
(best)
Worksurface
1/4-20 x 1/2” PHMS
(4 per upright)
1/4-20 x 1-3/4”
PHMS
(4 per leg)
Figure C3.1
Side Panel
Figure C3.2
4. Side Panels
1. Install any worksurface-mounted or internal equipment and route all cables.
2. Secure the side panels using the slots and 1/4-20 x 5/8” PHM screws
into the worksurface. Figure C4.
Side Panel
Figure C4
Note: The slots and tabs provided for the side panel can hold
the panel temporarily while the screws are being installed.
5. Display Stand
Display stand
1. If you have the optional display stand, proceed with the installation
at this time. (Instructions included with stand.) Figure 5.
Note: Requires mounting holes and
cutout on flat end of worksurface.
Figure 5
0118729R2 Page 9 of 11
Accessories
(Available separately after initial configured purchase)
Element Display Stand - 37130
•
•
•
•
Bolts directly to worksurface
Integrated cable management routes and hides wires
Adjustable (VESA-compatible) mount
Requires worksurface mounting holes and cutout
Monitor size range:
Weight capacity:
Vertical adjustment
(worksurface-to-center)
Tilting
Shipping weight:
Display stand
32”-55” [81.3 cm-139.7 cm] diagonal
200 lb [45.4 kg]
• 23.5”H [59.7 cm]
• 21.5”H [54.6 cm]
(5 vertical positions
• 19.5”H [49.5 cm]
in 2” increments)
• 17.5”H [44.5 cm]
• 15.5”H [39.4 cm]
15° range
35 lb [15.9 kg]
Mounting holes and cutouts
needed on flat end of worksurface
™
Cove Power Module - 99044
• Two power receptacles
• Two USB charge ports
(not data-compatible)
• Thumbscrew clamps
Cutout required:
Power cord:
Power receptacles:
USB charging ports:
Dimensions:
Unit weight:
• Requires worksurface cutout
• ETL listed
• Available in Black or Silver
5.25”W [13.3 cm] x 2”D [5.1 cm]
(mounts to surface thicknesses up to 1.5”)
9’ [274 cm] with 90° flat plug with 45° rotation
12A, 120 VAC spill-resistant
2.1A (10.5W)
6”W [15.2 cm] x 2.5”D [6.35 cm] x 3.18”H
[8.1 cm]
2.29 lb [1 kg]
See spectrumfurniture.com for the latest
accessories and detailed warranty information.
0118729R2 Page 10 of 11
Warranty
WE WILL MAKE IT RIGHT FOR YOU!
Spectrum is committed to provide complete customer satisfaction. Each of our products is manufactured from the best materials available and each
product is stringently monitored throughout the production process through our P.A.C.E. program (Product Assurance to meet Customer Expectations).
We expressly warrant that Spectrum products will be of good quality and workmanship and free from defect for the period set out in the warranty table below
from the date of delivery. This warranty shall not apply to defects or damage resulting from misuse, abuse, neglect, improper care, modification or repair not
authorized by Spectrum, or any other cause outside the control of Spectrum. Spectrum will, at its sole option, either repair or replace the defective product.
This warranty is exclusive; no other warranty, written or oral, is expressed or implied. This warranty is given by Spectrum to Buyer and to no other person or legal entity. No Spectrum dealer, distributor, agent or employee is authorized to make any modification or addition to this warranty.
NOTWITHSTANDING ANYTHING TO THE CONTRARY, SPECTRUM WILL NOT UNDER ANY CIRCUMSTANCES BE LIABLE FOR INDIRECT OR LIQUIDATED DAMAGES, INCLUDING CONSEQUENTIAL, INCIDENTAL AND SPECIAL DAMAGES. IN NO EVENT SHALL SPECTRUM’S LIABILITY, WHETHER
UNDER CONTRACT OR WARRANTY, IN TORT OR OTHERWISE, EXCEED THE PURCHASE PRICE RECEIVED BY SPECTRUM FOR THE PRODUCT AT
ISSUE AND “RECALL ACTION” EXPENSES. SPECTRUM SHALL NOT BE SUBJECT TO ANY OTHER OBLIGATIONS OR LIABILITIES, WHETHER ARISING OUT OF BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE AND STRICT LIABILITY) OR OTHER THEORIES OF LAW, WITH
RESPECT TO PRODUCTS SOLD OR SERVICES RENDERED BY SPECTRUM, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATING THERETO.
Our Customer Service Department is ready to provide immediate attention to any questions, comments or concerns. They are available to answer your calls
Monday through Friday from 7 am to 5 pm CST. In addition your product comments or concerns are welcome via e-mail at: [email protected].
Warranty Table
Item
Adjustable Crank / Electric Desk Legs
Flat Panel Desk Gas Cylinders
Chairs
• Adjustable Height Chair Parts – including frames, gas
cylinders, wood and plastic parts, control handles, casters
• Adjustable Height Chair Upholstery
• In-Stock Upholstery
• Graded-In Fabrics and Customer Owned Material
Height Adjustable Columns and Lifts
General Use Casters
Warranty Period
effective 1/1/2015
• 1 Year
• 7 Years
• 2 Years
• 2 Years
• No Warranty
• 1 Year
Electrical (including timers and LINAK actuators)
• 2 Years
Keyboard / Mouse Trays
• 1 Year
Flat Panel Monitor Arms
• Flat Panel Monitor Arm – General Parts
• Flat Panel Monitor Arm – Gas Cylinders
• 5 Years
• 2 Years
Desks and Lecterns
• Computer Desk Chassis
• Cart Chassis
• Lectern Chassis
• 10 Years
8
DESIGNED AND MANUFACTURED IN
CHIPPEWA FALLS
WISCONSIN.USA
925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM
© 2015 Spectrum Industries Inc., All rights reserved.
0118729R2 Page 11 of 11
">
