MOUNTUP MU6002-A Dual Monitor Desk Mount Instruction manual
Add to My manuals12 Pages
MOUNTUP MU6002-A is a dual monitor desk mount designed to provide ergonomic comfort and flexibility in your workspace. With its sturdy construction and adjustable features, it can accommodate monitors weighing up to 17.6 lbs each and supports various sizes from 75x75mm to 100x100mm VESA patterns. The gas spring mechanism allows for effortless height adjustment, while the tilt, swivel, and rotation capabilities ensure optimal viewing angles.
advertisement
▼
Scroll to page 2
of
12
Dual Monitor Desk Mount Instruction Manual 75x75mm 100x100mm (4.4~17.6LBS)x2 (2~8KG)x2 80002-MA11-24-US4.0 If you have any questions, please feel free to contact Customer Service via Amazon before returning. WARNING! If you have any confusions or are not quite sure about the installation, please do not hesitate to ask for our help. Before assembly, please check and make sure all necessary accessories are included and undamaged. Improper installation, such as use the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use. The kit contains small items that could be choking hazards if swallowed. Please keep them OUT OF REACH OF CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED. PACKAGE CONTENTS A (x2) A1 (x2) Upper Arm B (x2) Cable Cover C (x1) Lower Arm D (x1) Base Clamp All are included in D E1(x1) Pad E2(x2) Pad H (x1) 3mm Allen Key M-A (x8) M4x12mm F (x1) Wingnut G (x1) D1 Bracket Carriage Bolt I (x1) J (x1) 5mm Allen Key M-C (x8) M4x25mm D3 Bolt D4 Clip Plate K (x2) Bolt M6x8mm 6mm Allen Key M-B (x8) D2 Bolt Y Spacer H10mm M-D (x4) M6x8mm (Spare) NOTE: Not all hardware included will be used. (17.6LBS)x2 (8KG)x2 DO NOT EXCEED WEIGHT CAPACITY. 01 ASSEMBLY STEPS Warm Tips You could also refer to the Video Guide about installation on our product page. STEP 1: Apply Pads to the Base Bottom E2 Apply pads (E1&E2) to the base bottom to avoid desk scratches. E1 E2 STEP 2: Clamp Installation or Grommet Base Installation OPTION A: Clamp Installation Remove the plastic cover from Base (C). Mount Clamp (D) to the bottom of Base (C) by tightening bolts (K) with 5mm Allen Key (I). I Plastic Cover K C D Adjust the Clamp width to fit your desk. Secure stand to the desktop by tightening clamp (D). Fix the plastic cover to Base (C). Plastic Cover 0-1.97'' 0-50mm 02 STEP 2: (Continued) OPTION B: Grommet Base Installation If existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before installing the desk mount. Firstly detach Bracket (D1) from Clamp (D). ø ø 0.39~2.36" 10~60mm D D1 DESK DESK Then remove the plastic cover from Base (C). Run Carriage Bolt(G) through Base (C). Plastic Cover G C C By tightening Wingnut (F) after making Bracket (D1) through Carriage Bolt (G) and stacked above Wingnut (F), Base (C) would be fixed to your desk securely. Install the plastic cover to Base (C) finally. C 0-3.15'' 0-80mm G D1 F 03 STEP 3: Arm Installation Install the lower arm (B) to the base (C). Secure the arm by tightening the inside screw using 3mm Allen key (H). Note: If VESA plate is crooked, please hold it with both hands and rotate vigorously to make up arrows pointing up. B DO NOT tighten the screw excessively or it might be stripped. Note: Please note that the side with the label“ ” is installed on the base(C) when installing the lower arm(B) to the base (C). H C If the inside screws are stripped, you can use M-D spare screws. D If the inside screws are missing, you can use M-D spare screws. A H DO NOT tighten the screw excessively or it might be stripped. 04 STEP 4: Attach Monitor Monitor Monitor Monitor OPTION A: Flat Back Monitor M-A mm 3-5 75m 2.95m " 100m m 3.9" M-A Firstly choose suitable screws (M-A) according to the hole size of your monitor back; then assemble two of them with 3-5mm space left. Next hang your monitor onto VESA plate of Upper Arm (A). Finally finish the attachment by using a 6mm Allen Key (J) to tighten all chosen screws (M-A). Please make sure you don’t tighten the screws much excessively or it may cause your monitor damage. J M-A A monitor 75mm 2.95" 100mm 3.9" monitor OPTION B: Curved Back Monitor M-C M-B monitor m -5m 3 M-B M-C Firstly choose suitable screws (M-B) according to the hole size of your monitor back; then assemble two of them and Spacers (M-C) with 3-5mm space left. Next hang your monitor onto VESA plate of Upper Arm (A). Finally finish the attachment by using a 6mm Allen Key (J) to tighten all chosen screws (M-B) along Spacers (M-C). Please make sure you don’t tighten the screws much excessively or it may cause your monitor damage. J M-B A 05 M-C STEP 5: Tilt Adjustment Problem: Monitor tilts down. Solution: 1. Loosen the tilting bolt. 2. Hold the bottom of monitor with one hand and adjust to determine your desired tilt angle. 3. Retighten the tilting bolt to fix the intended angle. J 06 STEP 6: Adjust Tension The gas spring is pre-set to minimum tension. For intended functioning of the mount, you will need to adjust the tension of Upper Arm (A) in accordance with your monitor weight by 6 mm Allen Key (J). J NOTE: Be sure to keep the arm in a horizontal position during adjustment. Or else it would be difficult to adjust the mount or damage the mount. CAUTION Situation 1: Arm falls down Upper Arm with monitor falls down and fails to stay where intended. Solution: Turn the inside screw counterclockwise(“+”direction) to increase gas spring tension until the arm can stay as intended. Situation 2: Arm rises up or can't press down Upper Arm with monitor rises up and fails to stay where intended. Solution: Turn the inside screw clockwise(“-”direction) to decrease gas spring tension until the arm can stay as intended. 07 STEP 7: 5: Cable (Continued) STEP Management 7-1 Remove Cable Cover ● For lower arm: Remove the bottom plastic cover from lower arm as shown in the diagram below. Push and Slide 7-2 Attach Cable Cover ● For lower arm: Run cables through the cable cover, then insert and slide the cover down for reattachment; ● For upper arm: Run cables through the cable cover, then with both hands slightly press inwards the tabs inside the cover and insert it to upper arm. Insert and Push Press A1 Press Insert 08 Adjust as Desired Adjust monitor position and rotation. Tilt Swivel Rotation Height Swivel Swivel 360° 180° +90° 360° Tilt Swivel Rotation -45° 270° Height DESK DESK Please do not move stand outside desk for safety! Note: To ensure stability, the tightness of the rotating axis has been preset, so it would be kind of difficult to rotate the VESA plate. Suggestion: Please attach the monitor first, then hold the sides of it with both hands, and rotate vigorously. If that doesn't work out, please do not hesitate to ask for our help. 09 Product Dimensions 180° 200mm-280mm 1.97“ 50mm 2.95" 75mm 160mm 7.87"-11" 4.5" 114mm 360° 6.3“ 3.94" 100mm 270° +90° -45° 2.95" 100mm 160-415mm 4.5" 114mm 360° 6.3"-16.3" 3.94" 9.4" 240mm 75mm 10 CAUTION AND MAINTENANCE: ● Don't allow children to climb, stand, hang, or play on any part of monitor or stand. ● This product is intended for indoor use only. Using this product outdoors may lead to product damage or personal injury. ● Check if that the bracket is secure and safe to use at regular intervals (at least every three months).
advertisement
Key Features
- Supports two monitors up to 17.6 lbs each
- Adjustable height, tilt, swivel, and rotation for ergonomic positioning
- Gas spring mechanism for smooth and effortless adjustments
- Cable management system to keep cords organized
- Clamp and grommet mounting options for versatile installation
- Durable construction for stability and longevity
Related manuals
Frequently Answers and Questions
What is the maximum weight capacity of the mount?
Each arm can support up to 17.6 lbs, for a total weight capacity of 35.2 lbs.
Can the mount be used with monitors of different sizes?
Yes, the mount supports VESA patterns from 75x75mm to 100x100mm, accommodating monitors of various sizes.
Does the mount come with cable management features?
Yes, the mount includes cable covers to help keep cords organized and out of sight.
Can I adjust the height of the monitors independently?
No, the mount does not allow for independent height adjustment of each monitor.
advertisement