Chief PAN1 Panamorph & Anamorphic Lens Support Installation Manual
Add to My manuals8 Pages
Chief PAN1 is a lens support compatible with any RPA projector mount. It is designed to provide flexibility and precision in adjusting the position of the projector lens, allowing for optimal image alignment and projection. The PAN1 features:
-
Adjustable pitch: 20 degrees down and 10 degrees up, enabling you to angle the lens for precise image placement.
-
Variable extension: Up to 3 inches from the projector mount, giving you the flexibility to position the lens at the desired distance from the screen.
-
Lateral shift: 6-1/4 inches, allowing you to move the lens left or right to center it with the projector lens.
advertisement
▼
Scroll to page 2
of
8
INSTALLATION INSTRUCTIONS PAN-1 Lens Support The PAN-1 Lens Support is compatible with any RPA projector mount. PAN-1 LENS SUPPORT BEFORE YOU BEGIN • CAUTION: To prevent damage to the mount, which could affect or void the Factory warranty, thoroughly study all instructions and illustrations before you begin to install the mount brackets. Pay particular attention to the “Important Warnings and Cautions” on Page 2. • If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-582-6480. CHIEF MANUFACTURING INC. 1-800-582-6480 952-894-6280 FAX 952-894-6918 8401 EAGLE CREEK PARKWAY, SUITE 700 SAVAGE, MINNESOTA 55378 USA 8802-000178 (Rev. A) 2005 Chief Manufacturing www.chiefmfg.com 02/05 Instruction Instructions PAN-1 IMPORTANT WARNINGS and CAUTIONS! WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions. • WARNING Improper installation can result in serious personal injury! Make sure that the mounting surface can support a redundant weight factor five times the total weight of the equipment: if not, reinforce the structure before installing the PAN-1 on the projector. • WARNING Be aware of the potential for personal injury or damage to the unit if it is not adequately mounted. • CAUTION Inspect the unit for shipping damage. CONTENTS TOOLS REQUIRED FOR INSTALLATION................... 2 INSPECT PARTS BEFORE ASSEMBLY ..................... 3 Remove and Inspect the PAN-1 ................................ 3 PAN-1 INSTALLATION PROCEDURES....................... 4 Removing Projector from Ceiling Mount.................... 4 Attaching PAN-1 to RPA............................................ 5 Installing and Adjusting Lens..................................... 6 Adjusting PAN-1 to Projector Lens ............................ 7 Pitch Adjustment ................................................... 7 Extension Adjustment ........................................... 7 Lateral Shift Adjustment ........................................ 7 Height Adjustment................................................. 7 Adjustment Notes.................................................. 7 2 TOOLS REQUIRED FOR INSTALLATION • Phillips screwdriver • 9/64” Allen wrench or Hex wrench NOTE: Other tools may be required depending on the method of installation. Instruction Instructions PAN-1 INSPECT PARTS BEFORE ASSEMBLY Table 1. PAN-1 Parts Remove and Inspect the PAN-1 1. Open the shipping container and remove the PAN-1 from the container. 2. Carefully inspect the PAN-1 for shipping damage. If any damage is apparent, call your carrier claims agent and do not continue with the assembly procedure until the carrier has reviewed the damage. NOTE: Read all assembly instructions before starting assembly. 3. Carefully inspect all components for damage. See Table 1, Figure 1, and Figure 2 for details. ITEM PART NAME QTY 10 MAIN PLATE 1 20 FRONT ADJUSTABLE PLATE 1 30 SEMS SCREW, PAN, SELF-TAPPING, PHILLIPS 4 40 FRONT PLATE 1 50 1/4-20 X 3/4” CARRIAGE BOLT 1 60 KNOB 1 70 10-24 X 1-1/4” PHILLIPS HEAD MACHINE SCREW BZ 2 80 10-24 X 5/8” PHILLIPS HEAD MACHINE SCREW BZ (NOT SHOWN) 4 90 #10 SAE FLAT WASHER BZ 4 NYLON SPACER 2 100 70 20 10 60 30 and 90 50 40 Figure 1. PAN-1 Lens Support Figure 2. PAN-1 Lens Support (Top View) 3 Instruction Instructions PAN-1 PAN-1 INSTALLATION PROCEDURES To install the PAN-1 Lens Support (hereinafter called the PAN-1), perform the following procedures: • Removing Projector from Ceiling Mount Removing Projector from Ceiling Mount The projector must be removed from the mount before installing this accessory. With an assistant, remove projector from RPA ceiling mount as follows: • Attaching PAN-1 to RPA • Installing and Adjusting Lens • Adjusting PAN-1 to Projector Lens NOTE: If your projector is not installed on the RPA ceiling mount, proceed to the next procedure. RPA Ceiling Mount 1. Power-off the projector (see Figure 4). 2. Disconnect the power cord that supplies electric power to the projector. 3. Disconnect the audio/video cables from the projector. 4. Loosen the thumbscrews securing the projector to the RPA ceiling mount (see Figure 3). 5. Carefully slide the projector forward until the projector releases from the RPA ceiling mount. 6. Remove the projector. Thumbscrews (3 to 6 Places) Figure 3. Completely Installed PAN-1 — Example Disconnect audio/video cables from projector Disconnect AC power cord to projector Figure 4. Video Projector — Typical 4 Instruction Instructions PAN-1 Attaching PAN-1 to RPA Attach the PAN-1 to the RPA projector mount, as follows: NOTE: The four screws and washers removed from the RPA are located closest to the projector lens. Do not remove the screws and washers from the second set of slotted holes on the RPA. 1. On the RPA, remove two screws from the first set of slotted holes on the RPA (see Figure 5). RPA Remove screw pair closest to projector NOTE: 2nd screw pair on opposite side of RPA not shown 2. Remove the two center screws from the RPA. 3. On the PAN-1, loosen the two screws on each side to allow the bracket to extend backward and forward. Figure 5. Remove front screw pair from RPA 4. Slide the PAN-1 over the RPA projector mount, as shown in Figure 6. 5. Align the slotted holes on the PAN-1 with the slotted holes on the RPA. For reference, see step 1. RPA PAN-1 Install 80 and 90 6. Locate the parts bag supplied with the PAN-1. Find four 5/8” screws (80) and four #10 washers (90). NOTE: Leave the four screws (80) loose. These screws will be adjusted and tightened later. 7. Attach the PAN-1 to the RPA by installing four screws (80) and washers (90) into the threaded holes on the RPA (see Figure 6). NOTE: 2nd screw pair on opposite side of RPA not shown 8. Find two 1-1/4” Phillips screws (70) in the parts bag. NOTE: Stop threading each screw (70) when the end protrudes through the bracket hole approximately ¼” as shown in Figure 7. Figure 6. Attach PAN-1 to RPA 9. Install two screws (70) in the threaded tabs on the PAN-1 (see Figure 7). 70 Figure 7. Install Angle Adjustment Screws 5 Instruction Instructions PAN-1 Installing and Adjusting Lens Install and adjust the PAN-1 lens, as follows: 1. With an assistant, install your projector back on the ceiling mount at this time. Secure all thumbnuts and audio/video cables. Do not restore power to the projector at this time. See Figure 8. Projector Ceiling Mount 2. Install the PAN-1 lens at this time, as follows: a. Align the threaded holes in the PAN-1 lens with the holes in the front plate (40). b. Attach the PAN-1 lens using two nylon spacers (100) and two thumb knobs (supplied). c. Place the PAN-1 lens in the desired position and tighten the thumb knobs (see Figure 9. Figure 8. Install Projector on Ceiling Mount Nylon Spacer PAN-1 Lens Thumb Knobs (Supplied by Panamorph) Figure 9. Install PAN-1 Lens 6 Instruction Instructions PAN-1 Adjusting PAN-1 to Projector Lens The PAN-1 lens support can be adjusted to accommodate different projector models and lens placement. See Table 2. Lateral Shift Adjustment 3. To adjust lateral shift, do the following: a. Loosen the knob (60) and slide the lens left or right to the center of the projector lens. Table 2. PAN-1 Specification Chart Pitch: 20o down and 10o up Extension: 3 inches from projector mount Lateral Shift: 6-1/4 inches Height Adjustment: 3-5/8 inches up and down on front lens plate. b. Tighten the knob (60). Refer to Figure 10 and adjust the PAN-1 lens to the RPA projector lens, as follows: Pitch Adjustment 1. To adjust lens pitch, adjust the two angle screws to raise or lower the lens. This adjustment aligns the conversion lens with the projector lens. Extension Adjustment 2. To adjust lens extension (raise or lower the lens), do the following: a. Loosen four screws (30) and washers (90) on the side of the front adjustable plate (20). Height Adjustment 4. For height adjustment, do the following: a. Loosen the knob (60) and slide the PAN-1 lens up or down. b. Tighten the knob (60). Adjustment Notes NOTE: Except for fine-tuning, the PAN-1 is adjusted after completing the adjustment process. However, after restoring power to the projector, you may want to repeat a particular adjustment procedure in order to make minor changes. NOTE: Depending on your projector model, it may be necessary to adjust the lens at a slight angle to the projector lens, which helps to correct keystone. Or, loosen the lens knobs and tilt the PAN-1 lens as needed. b. Slide the front adjustable plate (20) back so the lens is approximately 1/8” to 1/4” from the projector lens. c. Tighten the four screws (30) and washers (90). Pitch Adjustment Extension Adjustment Lateral Shift Adjustment Height Adjustment Figure 10. Adjust PAN-1 Lens 7 Instruction Instructions PAN-1 THIS PAGE INTENTIONALLY LEFT BLANK 8
advertisement
Related manuals
advertisement