Epson Document Camera DC-13 Document Camera User's guide

Document Camera
User's Guide
Meaning of Symbols in the Guide
• Symbols for Safety
The documentation and this product use graphical symbols to show how to use this product safely.
The indications and their meaning are as follows. Make sure you understand and respect these caution symbols to avoid injury to persons or property.
Warning
This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.
Caution
This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.
• Symbols for General Information
Attention
Indicates information that, if ignored, could cause the product to malfunction or cause damage.
a
Indicates additional information and points which may be useful to know regarding a topic.
[Name]
Indicates button names for the remote control or the control panel.
Example: [Return] button
s
Menu Name
Indicates a page where detailed information regarding a topic can be found.
Displays Configuration menu items.
Example:
Select Brightness from Picture Quality.
Picture Quality - Brightness
Safety Instructions
Read this User's Guide and follow all safety instructions for your document camera. Keep this guide at hand for future reference.
Environmental Precautions
Warning
Do not use or store the document camera or remote control in a hot location, such as near a heater, in direct sunlight, or in a closed vehicle. Thermal damage, fire, or
malfunction may occur.
Do not use or store the document camera outdoors for an extended length of time, or where it may be exposed to rain, water, or excessive humidity. Fire or electric shock
may result.
Do not use or store the document camera where it may be exposed to smoke, steam, corrosive gases, or excessive dust. Fire or electric shock may result.
Caution
Do not set up the document camera near high-voltage electrical wires or sources of magnetic fields. This may interfere with correct operation.
Operate in the proper environmental conditions. s "General Specifications" p.57
Do not place or store the document camera where it is accessible to small children. It may drop or tip over, causing personal injury.
Do not place the document camera where it may be exposed to vibration or shock.
Electrical Precautions
Warning
Never open any covers on the document camera except as specifically explained in this User's Guide. Never attempt to disassemble or modify the document camera. Refer
all repairs to qualified service technicians.
Unplug the document camera from the outlet and contact your local dealer or Epson for help under the following conditions:
• If smoke, strange odors, or strange noises come from the device
• If liquid or foreign objects get inside the device
• If the device has been dropped or the housing has been damaged
Continuing to use under these conditions may result in fire or electric shock.
Do not attempt to use any adapter other than the AC adapter and power cord included with the device. Using an improper adapter may cause damage, overheating, fire, or
electric shock.
Be sure to use the AC adapter with the proper voltage indicated in this guide. Use of a different power source may result in fire or electric shock.
If the AC adapter, power cord, or document camera is damaged, turn the power off, unplug the AC adapter from the electrical outlet, and contact your local dealer or
Epson for help.
Do not touch the device, the AC adapter, or the plug with wet hands. Otherwise, you may receive an electric shock.
Do not use a power cord that is damaged. This may result in fire or electric shock. Take the following precautions when handling the power cord:
• Do not modify the power cord.
• Do not place heavy objects on the power cord.
• Do not bend, twist or pull the power cord excessively.
• Keep the power cord away from hot electrical appliances.
Take the following precautions when handling the plug. Failure to comply with these precautions could result in fire or electric shock.
• Do not overload wall outlets, extension cables, or power strips.
• Do not insert the plug into a dusty outlet.
• Insert the plug firmly into the outlet.
• Do not pull the power cord when disconnecting the plug; always be sure to hold the plug when disconnecting it.
Do not touch the plug during an electrical storm. Otherwise, you may receive an electric shock.
The cords included with this product contain chemicals, including lead, known to the State of California to cause birth defects or other reproductive harm. Wash hands
after handling. (This notice is provided in accordance with Proposition 65 in Cal. Health & Safety Code § 25249.5 and following.)
Caution
Turn off the document camera and unplug it after use.
Make sure the power is turned off, the plug is disconnected from the outlet, and all cables are disconnected before moving the document camera.
If a malfunction occurs due to static electricity, thunder, and so on, the product begins recovery operations. During recovery operations, do not touch any switches on the
product.
Installation Precautions
Warning
Do not use adhesives to prevent the screws from loosening and do not use oils or lubricants. This may cause the document camera housing to crack and could cause
serious injury.
Caution
Do not place the document camera in an unstable location, such as on a shaky table or slanted surface. The document camera may drop or tip over, causing personal
injury. If you use a table, cart, or stand, make sure it is stable and will not fall over.
When using the mounting points under the document camera to secure it to a table, cart, or stand, fasten the two bolts securely but do not overtighten them. Do not use
adhesives.
Do not place the document camera in a poorly ventilated place where heat can accumulate.
Do not place the document camera on a carpet, blanket, and so on, or cover it during use.
Do not install the document camera in a hot location, such as near a heater.
Route cables so that they are not a tripping hazard. Otherwise, they could trip someone and cause a fall or injury.
Cleaning Precautions
Warning
Use a dry cloth (or, for stubborn stains, a moist cloth that has been wrung dry) for cleaning. Do not use liquid, aerosol cleaners, or solvents such as alcohol, thinner or
benzine.
Do not place any containers of liquid on top of or near the document camera.
Do not spill liquid or spray fine mist into the document camera. Liquids entering the document camera may cause malfunction, fire, or electric shock. If you spilled liquid,
turn the power off, unplug the AC adapter from the electrical outlet, and contact your local distributor. Using the damaged device may cause fire or electric shock.
Never allow objects of any kind to enter any openings in the document camera. Do not leave objects, especially flammable objects, near the document camera. Doing so
may result in fire or electric shock.
Caution
Unplug the AC adapter from the outlet before cleaning to prevent electric shock.
Usage Precautions
Caution
Do not look into the lens when the LED illumination lamp is on. The bright light can damage your eyes.
Do not use excessive force when adjusting the document camera. The document camera may be broken, resulting in personal injury.
Do not place heavy objects on document camera. Otherwise, it may be damaged.
Do not try to press the arm flat or fold it backwards. Otherwise, it may be damaged.
Battery Precautions
Warning
Incorrect battery usage may cause batteries to rupture and leak battery fluid, which could result in fire, injury, or corrosion of the remote control.
If battery fluid gets in your eyes, do not rub your eyes. Wash them well with clean water and contact a doctor immediately.
If battery fluid enters your mouth, rinse immediately with plenty of water and contact a doctor immediately.
If battery fluid comes in contact with your skin or clothes, wash with water to prevent possible skin damage.
Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
Prepare two replacement manganese or alkaline AA batteries. Do not install batteries of different types, or mix new and old batteries.
Insert batteries so that the polarities (+ and -) are correct. Not doing so may cause leakage, overheating, or explosion.
Be sure to replace both batteries with new ones of the same type. Not doing so may cause leakage, overheating, or explosion.
Remove the batteries if you will not be using the remote control for a long period of time. When a battery runs down, take it out of the remote control immediately. If a
used-up battery is left inside for a long time, gas emitted from the battery may cause leakage, overheating, explosion, or damage to the remote control.
Do not expose batteries to heat, flame, or water.
Dispose of used batteries according to local regulations.
Contents
8
Meaning of Symbols in the Guide . . . . . . . . . . . . . . . . . . . 2
Projecting
Positioning the Document Camera . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Projecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Introduction
Included Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Document Camera Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Top/Side/Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Camera Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Plugging In and Turning On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
12
12
13
14
14
Remote Control Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Projector operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Document camera operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Switching the Projected Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Outputting Images and Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Freezing an Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Projecting Small Objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displaying Whiteboard Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Projecting Through a Microscope . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
25
25
26
26
26
27
Turning Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Displaying Saved Images as a Slideshow
Saving Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Recording Movies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Displaying a Slideshow (SD Card Viewer Function) . . . . . . . . . . . . 32
Connecting
Connecting the Document Camera Directly to a Projector . . . . . 18
Connecting Using a Computer Cable (Supplied) . . . . . . . . . . . . . . . . . . . . . . . . . 18
Connecting Using an HDMI Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
When Using a Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Dividing the Screen and Displaying Two Images (Split Screen) . . . . . . . . . . .
Displaying live images and images on an SD card . . . . . . . . . . . . . . . . . .
Displaying two images on an SD card . . . . . . . . . . . . . . . . . . . . . . . . . .
Available combinations for the Split Screen function . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
33
34
35
36
Image Adjustments and Effects
Connecting to a Projector Using a Computer . . . . . . . . . . . . . . . . . 20
Using the On-screen Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
On-Screen Menu Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Image Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Function Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SD Card Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Info Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
39
40
41
42
Contents
9
Using the Computer Software
Symbols Indicating the Device Meets the IEC60950-1 A2 Safety
Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Using Easy Interactive Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
General Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Operating Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Uninstalling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Copyrights and Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Using Other Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Uninstalling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Solving Problems
Problems and Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Operation Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Image Quality Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SD Card Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Problems Connecting a Laptop . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
49
49
49
50
Epson Projector Contact List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
EUROPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AFRICA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MIDDLE EAST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NORTH, CENTRAL AMERICA & CARIBBEAN ISLANDS . . . . . . . . . . . . . . . .
SOUTH AMERICA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ASIA AND OCEANIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
51
53
53
54
54
54
Notices
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Responsible Use of Copyrighted Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Introduction
You can use this document camera to capture and project pages from books or other documents, and even three-dimensional objects. You can also use the
software supplied to operate the document camera from a computer.
Included Items
•
•
•
•
•
•
•
•
Remote control with 2 AA batteries
Power cord and adapter
Computer cable
USB cable
EPSON Document Camera Software CD-ROM
Document CD-ROM
Quick Start Guide
Microscope adapter
11
Document Camera Parts
12
Name
Top/Side/Rear
G Security cable installation
point
Function
Lets you attach a commercially available security
cable to lock the document camera in place.
Camera Head
Name
Function
A Camera head
s "Camera Head" p.12
B Remote receiver
Receives signals from the remote control.
C Control panel
s "Control Panel" p.13
D SD card slot
Lets you save and display images on an SD card.
s "Displaying Saved Images as a Slideshow"
p.29
A Microphone
Captures sound when you record a video.
B [
Changes the LED lamp status in three steps: bright,
dim, and off.
E Security slot
The security slot is compatible with the Microsaver
security system manufactured by Kensington.
C LED lamp
Provides additional light when there is not enough
light on your document.
F Interface
s "Interface" p.14
D Image rotation dial
Rotates the projected image by ±90 degrees.
Name
] Lamp switch
Function
Document Camera Parts
Name
13
Function
E Camera lens
Captures the image.
F Camera arm
Extends or retracts to adjust the height of the camera
head.
Name
B [Source] button
[ ][
]
C [Menu] button
Opens and closes the menu.
D [ ][ ][ ][ ]
buttons
When the menu screen is displayed, pressing these
buttons selects menu items and setting values.
[
Control Panel
[
Name
A [t] power button
Function
Turns the document camera on or off.
Switches the output image to the device connected
to the Display Out port.
[ ]: Projects images (live or on an SD card) from
the document camera.
[
]: Projects images from a computer connected
to the Computer In port.
Attention
Do not rub the lens with harsh materials or subject it to shock, as it can be
easily damaged. Use a soft cloth to gently wipe the lens.
Function
][
][
] buttons
] buttons
Adjusts the brightness of the image if pressed while
projecting images from the document camera.
Adjusts the focus of the image if pressed while
projecting images from the document camera.
E [Enter] button
• When the menu is displayed, pressing this button
confirms the current item.
• Displays the SD Card menu and images on the SD
card if pressed while projecting live images.
s "Displaying a Slideshow (SD Card Viewer
Function)" p.32
F [Esc] button
Stops the current function. When the menu is
displayed, pressing this button moves to the
previous menu level.
G [Zoom] button
[z] [x]
Enlarges or reduces the image without changing the
projection size.
H [Capture] button
[ ]
Captures still images.
s "Saving Images" p.30
I [Focus] button
Focuses the image automatically.
The document camera cannot focus on objects that
are approximately 10 cm (4 inches) or less from the
surface of the camera lens.
J [Freeze] button
Freezes live images. Press the button again to resume
projection.
Document Camera Parts
Name
K [Record] button
[ ]
14
Function
Starts and stops video recording.
Base
Interface
Name
Name
Function
A Mounting points
A Power (AC adapter/DC In) Connects the supplied power cord and adapter.
port
B Computer In port
Inputs image signals from a computer.
C Display Out port
Outputs images to image devices such as projectors.
D HDMI port
Outputs images and audio to a video device that is
compatible with HDMI signals.
E USB-B (TypeB) port
Connects the document camera to your computer
with the USB cable supplied. By using the software
supplied, you can operate the document camera
from a computer.
Function
You can attach the document camera to a table, cart,
or stand with commercially available M4 bolts. You
can thread them to a maximum depth of 9 mm
(0.35 inch).
Attention
Fasten the bolts securely but do not
overtighten them. Do not use adhesives.
B Security cable installation
point
Lets you attach a commercially available security
cable to lock the document camera in place.
Remote Control Buttons
Remote Control
15
Projector operations
Name
Function
A [t] power button
When used with an Epson projector, turns the
projector on or off.* You cannot operate the
document camera with this button.
B [A/V Mute] button
Turns the video and audio of an Epson
projector on or off.*
C [Source Search] button
Changes the input source connected to an Epson
projector.*
* This is not supported by some projectors. For more details, contact your local
dealer or the nearest service center provided in this guide.
s "Epson Projector Contact List" p.51
Document camera operation
Name
Function
D [t] power button
Turns the document camera on or off. You cannot
operate a projector with this button.
E [Auto Focus] button
Focuses the image automatically.
The document camera cannot focus on objects that
are approximately 10 cm (4 inches) or less from the
surface of the camera lens.
F [Rotate Image] button
[ ]
Lets you turn an image upside-down.
G [Menu] button
Opens and closes the menu.
H [ ][ ][ ][ ]
buttons
When the menu screen is displayed, pressing these
buttons selects menu items and setting values.
I [Enter] button
• When the menu is displayed, pressing this button
confirms the current item.
• Displays the SD Card menu and images on the SD
card if pressed while projecting live images.
Remote Control Buttons
Name
16
Function
J [Brightness] button
[
][ ]
Adjusts the projected image brightness.
K [SD Card Viewer] button
Projects images and movies on the SD card as a
slideshow. Press the [Single] button to display the
image on one screen, and press the [Split] button to
display two images on the left and right.
s "Displaying a Slideshow (SD Card Viewer
Function)" p.32
L [Camera] buttons
Projects live images from the document camera.
M [Zoom] button
[z] [x]
Enlarges or reduces the image without changing the
projection size.
N [Focus] button
[ ][ ]
Adjusts the focus of the image manually.
O [Esc] button
Stops the current function. When the menu is
displayed, pressing this button moves to the
previous menu level.
P [Record] button
[ ]
Starts and stops video recording.
Q [Capture] button
[ ]
Captures still images.
R [Freeze] button
Freezes live images. Press the button again to resume
projection.
S [Source] button
[
][ ]
Switches the output image to the device connected
to the Display Out port.
[
]: Projects images from a computer connected
to the Computer In port.
[ ]: Projects images (live or on an SD card) from
the document camera.
T Remote control lightemitting area
Outputs remote control signals.
Connecting
Follow the instructions in this section to set up the document camera.
Connecting the Document Camera Directly to a Projector
You can connect the document camera directly to image devices, such as a
projector or external monitor, using a computer cable or HDMI cable.
a
18
the document camera are output from the projector. Only audio from the
SD card is output.
You can also connect the document camera to a projector through a
computer.
s "Connecting to a Projector Using a Computer" p.20
Connecting Using a Computer Cable (Supplied)
Connect the Display Out port on the document camera to a projector using
the computer cable. Images (live or on an SD card) from the document
camera are output from the projector. Audio is not output.
a
When image devices that support the HDMI CEC standard are
connected to the document camera, operations for the document
camera and the image device can be linked together. Set HDMI Link
on the document camera. s Function - HDMI Link p.40
For necessary settings on the image device, see the documentation
provided with the device.
When Using a Computer
Connecting Using an HDMI Cable
Connect the HDMI port on the document camera to a projector using an
HDMI cable (commercially available). Images (live or on an SD card) from
When the Computer In port on the document camera is connected to a
computer using a computer cable, you can project PowerPoint slides or
images from any other application from a projector.
Connecting the Document Camera Directly to a Projector
a
• This connection method is only available when the document
camera is connected to a computer using a computer cable. If the
computer you are using does not have a VGA output port, connect
the computer directly to the projector.
• Images on the computer connected to the document camera are only
output from the Display Out port.
You can switch the projected image between [ ] or [ ] using
the [Source] button on the document camera or the remote control.
[
[
]: Projects images from a computer.
]: Projects images (live or on an SD card) from the document camera.
19
Connecting to a Projector Using a Computer
When the document camera is connected to a computer using a USB cable,
you can operate the document camera from the computer. Using the
software supplied, you can save images and video, adjust picture quality,
zoom, and so on.
s "Using the Computer Software" p.43
Connect the USB-B port on the document camera to a computer using a
USB cable.
Next, connect the computer to the projector. The cable used to create the
connection differs depending on the computer and projector you are using.
See the documentation provided with the computer and projector you are
using.
a
• You cannot project images by directly connecting the document
camera to a projector with a USB cable.
• Connect the document camera to a USB 2.0 port of a computer. If
you connect it to a USB 3.0 port, it may not function properly.
• Do not connect multiple document cameras to one computer at the
same time.
20
Projecting
Positioning the Document Camera
a
Raise the camera arm with one hand while holding the base of the
camera with your other hand.
b
Rotate the camera arm as shown.
22
Attention
Do not try to press the arm flat or fold it backwards. Otherwise, the
document camera may be damaged.
The camera arm can only rotate within the range shown below.
c
Position the camera head above the projection area.
Plugging In and Turning On
Connect the document camera to the projector with a cable before turning
on the document camera. s "Connecting" p.17
a
Connect the power cord as shown and plug the cord into a wall
outlet.
b
Press the [t] power button on the document camera or remote
control.
The power indicator flashes blue. When startup is complete, the
power indicator and the camera indicator are lit blue. Startup takes
approximately 15 seconds.
c
Turn on your projector.
23
d
Select the appropriate source on the projector depending on the
port to which you connected.
Live images from the document camera are projected from the
projector.
Projecting
a
24
Place your document on the table under the camera head. Align
the center of your document with the
mark on the side of the
document camera.
a
• When projecting A4-size or letter size paper, align the edge of
the paper with the guides on the side of the document
camera.
• The maximum paper size that can be projected is A3
landscape.
a
c
If necessary, you can adjust the brightness of the image using
the [
] or [
] on the document camera or remote control.
Press the [Focus] button on the document camera or the [Auto
Focus] button on the remote control.
The focus is adjusted automatically.
a
b
Slide the [
] lamp switch to illuminate the document.
d
To sharpen hard-to-focus objects, use the [
]/[
the document camera, or the [Focus] buttons [
remote control.
] buttons on
]/[
] on the
To zoom in on part of the image, press the [Zoom] - [z] button on
the document camera or remote control. Press the [Zoom] - [x]
button to zoom out.
Projecting
a
25
• You can zoom up to 16x. When using the zoom function, you can
scroll (Pan/Tilt) the enlarged image by pressing the [ ], [ ], [ ],
and [
] buttons.
• Image quality declines when using the zoom function.
Outputting Images and Sound
When connecting multiple devices to one document camera, the image and
audio are output as follows.
When [
Switching the Projected Image
When a computer is connected to the document camera, you can switch the
image projected from the projector using the [Source] button on the
document camera or the remote control.
] is selected using the Source button
• Display Out port: Images from the computer
• HDMI port: Live images from the document camera
• USB-B port: Live images from the document camera and audio from
the internal microphone
a
When [
Images on the computer connected to the document camera are only
output from the Display Out port.
] is selected using the Source button
When projecting live images from the document camera
• Display Out port: Live images from the document camera
• HDMI port: Live images from the document camera
• USB-B port: Live images from the document camera and audio from
the internal microphone
a
[
[
]: Projects images from a computer.
]: Projects images (live or on an SD card) from the document camera.
When recording live images or taking photos using the document
camera, images and audio cannot be output from the USB-B port.
When projecting images from an SD card
• Display Out port: Images from the SD card
• HDMI port: Images and audio from the SD card
a
When a computer is connected to the USB-B port, the SD card viewer
is unavailable.
Projecting
26
Freezing an Image
Press and release the [Freeze] button on the document camera or the
remote control to freeze the image.
After freezing the image, you can remove your document while leaving its
image displayed on the screen. Place your next document under the camera
lens and press the [Freeze] button again; your presentation continues
without interruption.
Projecting Small Objects
To project a small object, lower the camera arm. You can place the camera
head within approximately 10 cm (4 inches) of the object.
To zoom in on part of the image, press the [Zoom] - [z] button on the
document camera or remote control. Press the [Zoom] - [x] button to
zoom out.
b
Press the [Focus] button on the document camera or the [Auto
Focus] button on the remote control.
Displaying Whiteboard Images
You can use the document camera to display a lecture or presentation at
the front of a room, or to capture images of a whiteboard or chalkboard.
a
a
Press the [Rotate Image] button [ ] on the remote control to turn
an image upside-down. You can also rotate the image by pressing
the [Menu] button and then selecting Image > Image Rotation > 180
degrees.
Rotate the camera head and set it in the direction of the object.
The image is automatically focused.
a
You can make an audio/video recording of your projection. The
recorded images are saved to the SD card.
s "Recording Movies" p.31
Projecting
27
Projecting Through a Microscope
Projected image
To display objects as seen through a microscope, use the included
microscope adapter.
a
• Before installing the document camera, make the following settings:
- Focus the microscope and adjust the zoom
- Press the [Menu] button, and then select Image > Microscope >
On.
• Images may not be displayed correctly depending on the optical
properties of your microscope.
a
Attach the microscope adapter to the image rotation dial. Push the
adapter while holding down the attachment buttons on the
microscope adapter.
b
Position the camera head on the microscope lens. Extend the
adapter ring and attach it to the microscope's eye piece. You can
extend the adapter ring by up to 5 mm (1/4 inch).
Turning Off
Turn off the document camera after use.
a
Press the [t] power button on the document camera or remote
control.
The following message is displayed on the projected image.
b
Press the [t] power button again.
c
Disconnect the power cord and any other connected cables, and
then fold down the camera arm.
The projected image disappears, and the power indicator turns off.
28
Displaying Saved Images as a Slideshow
You can save live images from the document camera to an SD card and then display the saved images and movies as a slideshow.
This section explains how to perform operations using the document camera or the remote control. You can save images using software on your computer.
s "Using the Computer Software" p.43
a
• FAT16 SD cards (up to 2 G) and FAT32 SDHC cards (up to 32 GB) are supported.
• EX-FAT SDXC cards are not supported.
• SD cards with a security function cannot be used.
Attention
In the following situations, data on the SD card may be lost or corrupted.
• If the card is subjected to static electricity or electronic noise
• If the card is not handled correctly
• If a malfunction occurs or during repairs
• If damage occurs due to a natural disaster
Note that Epson accepts no responsibility for lost or corrupted data, even if the loss occurs during the warranty period.
Saving Images
30
You can save images from the document camera to an SD card as still
images.
a
• Images are saved in JPEG format (1920 x 1080).
• You can change the background color for the image in Background
Color. When White is set and the image is saved, if you print the
image on white paper, the area around the image may not stand
out. s Function - Background Color p.40
a
Insert an SD card into the SD card slot on the document camera.
b
c
Project the image you want to save.
Press the [Capture] [
] button to capture the image.
The number of photos available is displayed at the top right of the
screen next to
, and captured images are saved to the following
folder on the SD card:
d
Repeat steps 2 and 3 for any additional images you want to save.
a
If there is no space on the SD card, the message "No free space
on the SD Card." is displayed, and the image is not saved.
Recording Movies
31
You can save images and audio from the document camera to an SD card
as movies.
a
The recording indicator is lit blue while recording.
a
• Movies are saved in AVI format (images: Motion JPEG 720p/30 fps,
audio: Linear PCM).
• You can record individual files at the following sizes:
Capacity: up to 2 GB
Recording time: up to approximately 29 minutes
If the maximum capacity or recording time are exceeded while
recording, the movie up to that point is saved and the recording
ends.
• The following operations are available while recording.
Freeze, Zoom (Pan/Tilt), Auto Focus, Brightness adjustment,
Focus adjustment
Note that operation sounds are also recorded.
• While recording, a blue screen is displayed on the computer
connected to the document camera using a USB cable.
• Set Sleep Mode to Off to prevent the power turning off while
recording. s Function - Sleep Mode p.40
a
b
c
Project the image you want to save.
Press the [Record] button [
] to start recording.
• If there is no space on the SD card, the message "No free
space on the SD Card." is displayed, and the movie is not
saved.
• Do not remove the SD card while recording.
• You can check the amount of available free space on the SD card in
SD Card Info. s SD Card - SD Card Info. p.41
Insert an SD card into the SD card slot on the document camera.
• While recording, the elapsed time is displayed at the top right
of the screen. This is not displayed on the saved image.
d
To stop recording, press the [
] button again.
While saving recordings, the recording indicator flashes blue, and
when saving is complete the indicator turns off. Movies are saved to
the following folder on the SD card:
Displaying a Slideshow (SD Card Viewer Function)
32
You can display images saved on an SD card as a slideshow.
a
This function is unavailable in the following situations:
• When the document camera is connected to a computer using a USB
cable
• When recording a movie
• When a 480p signal is being output from the HDMI port
Files that can be played as a slideshow
Type
File Type
Still im‐
ages
JPEG
(DCF-compliant)
Files with a resolution over 7680 x 5760 pixels
cannot be played.
Movies
AVI
(images: Motion JPEG,
audio: Linear PCM)
Files that are larger than 2 GB cannot be
played.
a
You can start a slideshow using the [Enter] button on the
document camera or the remote control. Press the [Enter]
button while projecting a live image, and then select Single
Screen from the SD Card menu.
Notes
You can also display files that were not captured by the document
camera as a slideshow. To display files, they must be saved to the
specified folder. See the following for more details.
Thumbnails
s "SD Card Problems" p.49
a
Press the [Single] button on the remote control.
a
b
The final file and thumbnail on the SD card are displayed.
If a file cannot be displayed because it is damaged or too big, a
black screen is displayed.
Press the [ ] [ ] buttons to select the thumbnail for the file you
want to display.
Press the [
] [
] buttons to change the thumbnails page.
Displaying a Slideshow (SD Card Viewer Function)
c
33
Press the [Enter] button to hide the thumbnails.
Thumbnail *2
[ ] button: Displays the previous file.
*1
*2
[ ] button: Displays the next file.
[Esc] button: Displays the thumbnails again.
d
If the images on the SD card are rotated when displayed by the
document camera, the original image can be saved as the rotated
image. Backup data on the SD card to other media as often as
necessary.
f
e
Press the [Menu] button to access the following functions.
Rotate to
Right *1
Rotates the image 90 degrees to the right.
Rotate to Left *1
Rotates the image 90 degrees to the left.
Delete
Deletes the selected file.
Split Screen *1
The screen switches to a split screen display, and
you can display a live image and an image on the
SD card on the left and right.
Return to Camera
The slideshow is closed and a live image is
displayed.
This is not available while a movie is being displayed.
This is not displayed while thumbnails are displayed.
Attention
Hide the thumbnails, and then press the [Enter] button to play the
movie.
Press the [Enter] button to pause/play the movie.
Displays thumbnails.
End the slideshow by pressing the [Camera] button on the remote
control.
a
You can also close the slideshow by pressing the [Esc] button
when thumbnails are displayed.
Dividing the Screen and Displaying Two Images
(Split Screen)
You can display live images and images on an SD card side-by-side on the
screen. You can also display two images on an SD card at the same time.
Displaying a Slideshow (SD Card Viewer Function)
34
Displaying live images and images on an SD card
a
a
Press the [Split] button on the remote control.
c
When projecting a live image from the document camera, you
cannot display a movie from the SD card.
Press the [Enter] button to hide the thumbnails.
[ ] button: Displays the previous file.
[ ] button: Displays the next file.
[Esc] button: Displays the thumbnails again.
A live image and an image on the SD card are displayed side-by-side
on the screen.
a
d
You can start the split screen projection using the [Enter]
button on the document camera or the remote control. Press
the [Enter] button while projecting a live image, and then select
Split Screen from the SD Card menu.
Press the [Menu] button to access the following functions.
Some functions are not available depending on the image being
projected.
*
b
] [
] buttons to change the thumbnails page.
Rotates the image 90 degrees to the right.
Rotate to Left
Rotates the image 90 degrees to the left.
Single Screen
Changes to a single image display.
Flip
Switches the images on the left and right.
Camera/SD
Mode
SD/SD Mode
Changes the combination of displayed images.
• Live Image and Image on SD card
• Two Files on SD Card
Return to Camera
The slideshow is closed and a live image is
displayed.
Thumbnail *
Displays thumbnails.
This is not displayed while thumbnails are displayed.
a
Press the [ ] [ ] buttons to select the thumbnail for the image
you want to display.
Press the [
Rotate to Right
e
You can use the following adjustment functions for live images.
Brightness adjustment, Focus adjustment (automatic and
manual), Freeze, Zoom (Pan/Tilt)
End the slideshow by pressing the [Camera] button on the remote
control.
Displaying a Slideshow (SD Card Viewer Function)
a
35
You can also close the slideshow by pressing the [Esc] button
when thumbnails are displayed.
Displaying two images on an SD card
a
Press the [Split] button on the remote control.
b
Press the [Menu] button on the document camera or the remote
control, and then select SD/SD Mode.
A live image and an image on the SD card are displayed side-by-side
on the screen.
Two files on the SD card are displayed side-by-side on the screen.
a
You can start the split screen projection using the [Enter]
button on the document camera or the remote control. Press
the [Enter] button while projecting a live image, and then select
Split Screen from the SD Card menu.
You can change the file surrounded by the orange frame.
c
Press the [ ] [ ] buttons to select the thumbnail for the file you
want to display.
Press the [
d
] [
] buttons to change the thumbnails page.
To move the orange frame between the right and left of the
screen to re-select the file, press the [Menu] button while
thumbnails are displayed, and then select Change Focus.
Displaying a Slideshow (SD Card Viewer Function)
36
Left Source
Right Source
SD Card Movie
SD Card Image
a
e
Press the [Enter] button to hide the thumbnails.
[ ] button: Displays the previous file.
[ ] button: Displays the next file.
[Esc] button: Displays the thumbnails again.
f
End the slideshow by pressing the [Camera] button on the remote
control.
a
You can also close the slideshow by pressing the [Esc] button
when thumbnails are displayed.
Available combinations for the Split Screen function
Left Source
Right Source
Live Image
SD Card Image
SD Card Image
Live Image
SD Card Image
SD Card Image
Movies cannot be displayed on the right-hand side of the screen.
Image Adjustments and Effects
The document camera provides a full range of image adjustments and effects, including freeze image, black-and-white, and the ability to change the display for
color images.
Using the On-screen Menu
Press the [Menu] button on the document camera or remote control to
view the on-screen menu. See the following for details on each item in the
on-screen menu.
s "On-Screen Menu Table" p.39
The following menu is displayed:
Use the [ ] [ ] [ ] [ ] buttons to navigate the menu and adjust the
settings. Press [Enter] to select a setting. When you are done adjusting the
settings, press the [Menu] or [Esc] button to close the menu and save your
settings.
a
The menu cannot be displayed when connecting to a computer using a
USB cable.
38
On-Screen Menu Table
39
Image Menu
Setup Item
Explanation/Select
White Balance
Select the setting according to the lighting in the room where you are using the document camera.
Auto*: Automatically adjusts the image color according to the display environment.
Cloudy: Suitable for use in cloudy weather.
Daylight: Suitable for use in fair weather.
Fluorescent: Suitable for use in a room with fluorescent lighting.
Incandescent: Suitable for use in a room with incandescent lamps.
Image Mode
You can select from the following settings to adjust for the image type you are displaying:
Normal*: Default setting.
Text: Suitable for projecting black-and-white text.
Display: Suitable for projecting images from a tablet display, and so on.
Color/B&W/Negative
Select the display method for color images.
Color*: Displays the image in color.
Black&White: Displays the image in black-and-white.
Negative: Displays a photographic negative in true color.
Image Rotation
Lets you rotate the image.
Normal*: Displays the image as it actually is.
180 degrees: Displays the image upside-down.
Microscope
Optimizes the image settings for use with a microscope.
On: Sets the optimal image settings for use with a microscope.
Off*: Returns to the normal settings.
Noise Reduction
Settings related to Noise Reduction for the live image.
Off: Deactivates Noise Reduction.
NR1, NR2, NR3: Enables Noise Reduction. Use this setting if noise occurs.
Advanced
Makes advanced settings of live image.
Exposure: Adjusts the light volume of images.
Contrast: Adjusts the difference between bright and dark areas of images.
Color Adjustment: Adjusts the reddish and bluish colors of the whole image.
Edge Enhancement: Adjusts the emphasis on the contours of the image.
Gamma: Adjusts the coloring that occurs while displaying the image.
On-Screen Menu Table
40
Setup Item
Explanation/Select
Resets the Image menu settings to the default values.
Reset
* Default setting at time of purchase
Function Menu
Setup Item
Explanation/Select
Output Resolution
Sets the output resolution when connecting a computer cable to the Display Out port.
Auto*: Sets automatically according to the resolution of the image device.
XGA 1024x768
WXGA 1280x800
WXGA 1360x768
SXGA 1280x1024
Full HD 1920x1080
HDMI Output
Sets the output resolution when connecting an HDMI cable to the HDMI port.
Auto*: Sets automatically according to the resolution of the image device.
SDTV (480p)
HDTV (720p)
HDTV (1080p)
Mic. Volume
Sets the volume for the internal microphone.
HDMI Link
When image devices that support the HDMI CEC standard are connected to the document camera, operations for the
document camera and the image device can be linked together.
HDMI Link: Set to On* to enable the HDMI Link function. The changes are enabled when you turn off the document
camera.
Power On/Off Link: When this is set to On, the connected device turns on when the document camera is turned on.
Also, when the connected device is turned off, the document camera turns off. The default setting is Off.
Sleep Mode
Operation settings when the document camera is inactive.
On: The power automatically turns off if the document camera is inactive for a certain amount of time.
Off*: The power remains on even if the document camera is inactive for a certain amount of time.
On-Screen Menu Table
41
Setup Item
Explanation/Select
Sleep Mode Timer
Sets the time from when the document camera is last operated until the power automatically turns off in Sleep
Mode.
1 to 6 hour(s)
Background Color
Select the display background for the projected image.
Black*
White
Flicker Reduction
Eliminates flicker when giving presentations in regions with different electrical systems.
50Hz*
60Hz
Language
Changes the on-screen menu language.
Reset
Resets the Function menu settings to the default values.
* Default setting at time of purchase
SD Card Menu
You can only make settings when an SD card has been inserted in the document camera.
Setup Item
Explanation/Select
Single Screen
The slideshow starts.
Split Screen
Split screen projection starts.
SD Card Info.
Displays information about the SD card.
Memory Status: Displays the usage ratio of the SD card.
Recordable Images: Displays the number of images that can be stored on the SD card.
Total Memory: Displays the total capacity of the SD card.
On-Screen Menu Table
42
Info Menu
Setup Item
Explanation
Output(HDMI)
Displays the set content for HDMI Output. s "Function Menu" p.40
Output(RGB)
Displays the output resolution for the image signal.
Version
Displays the firmware version for the document camera.
Serial Number
Displays the serial number for the document camera.
Using the Computer Software
The included software lets you operate the document camera from a computer.
The software also lets you capture live images and record them as movies.
Using Easy Interactive Tools
44
When using the Easy Interactive Tools camera screen, you can display
images from the document camera on a computer connected via a USB
cable. You can adjust the image size, brightness, and so on, and save it as
an image file or a movie file.
For more details on Easy Interactive Tools, see the Easy Interactive Tools
Operation Guide.
a
When projecting an image using a projector that supports the
interactive pen or touch operations, you can operate the Easy
Interactive Tools on the projected image.
Windows 10
CPU
Intel Core2 Duo 1.2 GHz or faster
Recommended: Intel Core i3 or faster
Amount of Memory
1 GB or more
Recommended: 2 GB or more
Hard Disk
Space
100 MB or more
Display
Resolutions no lower than XGA (1024 x 768) and no
higher than WUXGA (1920 x 1200)
Display color of 16-bit color or more
Operating Requirements
* Service Pack 2 or later
Windows
OS
Home 32/64 bit
Pro 32/64 bit
Enterprise 32/64 bit
Education 32/64 bit
Windows Vista*
Windows 7
Windows 8
Windows 8.1
Ultimate 32 bit
Enterprise 32 bit
Business 32 bit
Home Premium 32 bit
Home Basic 32 bit
Ultimate 32/64 bit
Enterprise 32/64 bit
Professional 32/64 bit
Home Premium 32/64 bit
Home Basic 32 bit
Windows 8 32/64 bit
Windows 8 Pro 32/64 bit
Windows 8 Enterprise 32/64 bit
Windows 8.1 32/64 bit
Windows 8.1 Pro 32/64 bit
Windows 8.1 Enterprise 32/64 bit
Mac
OS *
OS X 10.7.x
OS X 10.8.x
OS X 10.9.x
OS X 10.10.x
OS X 10.11.x
macOS 10.12.x
CPU
Intel Core2 Duo 1.2 GHz or faster
Recommended: Intel Core i5 or faster
Amount of Memory
1 GB or more
Recommended: 2 GB or more
Hard Disk
Space
100 MB or more
Using Easy Interactive Tools
Resolutions no lower than XGA (1024 x 768) and no
higher than WUXGA (1920 x 1200)
Display color of 16-bit color or more
Display
* Requires QuickTime 7.7 or later.
Installing
a
• The software should be installed by a user with administrator access.
• Close all running applications before starting the installation.
Windows
a
b
Turn on your computer.
Insert the EPSON Document Camera Software CD-ROM in your
computer.
The installer screen is automatically displayed.
c
Select Drawing on the Camera screen on the installer screen to
start installation.
45
Uninstalling
Windows Vista/Windows 7
a
b
c
Click Start, and then Control Panel.
Click Uninstall a program.
Select Easy Interactive Tools Ver.X.XX, and then click
Uninstall.
Windows 8/Windows 8.1
a
b
c
Select Search on the Charms, and then search for Easy
Interactive Tools Ver.X.XX.
Right-click (press and hold) Easy Interactive Tools Ver.X.XX, and
then select Uninstall from the app bar.
Select Easy Interactive Tools Ver.X.XX, and then select
Uninstall.
Windows 10
Double-click the Install Navi icon in the EPSON window.
a
b
c
d
Select Drawing on the Camera screen on the installer screen to
start installation.
Mac
Mac
a
b
Turn on your computer.
Insert the EPSON Document Camera Software CD-ROM in your
computer.
The installer screen is automatically displayed.
c
d
a
Right click Start.
Click Control Panel.
Click Uninstall a program.
Select Easy Interactive Tools Ver.X.XX, and then click
Uninstall.
Double-click Application - Easy Interactive Tools Ver.X.XX.
Using Easy Interactive Tools
b
c
Run Easy Interactive Tools Uninstaller from the Tools folder.
Follow the on-screen instructions to uninstall.
46
Using Other Software
You need to install TWAIN Driver for Epson Document Camera (Ver. 2.00
or later) to use software that supports TWAIN. (Supports Windows only)
Installing
a
b
c
Insert the EPSON Document Camera Software CD-ROM in your
computer.
Double-click Computer - TWAIN Driver for Epson Document
Camera - setup.exe.
Follow the instructions on the screen to install all the software.
Windows Vista/Windows 7
Click Start - Control Panel.
Click Uninstall a program.
Select TWAIN Driver for Epson Document Camera Ver.X.XX, and
then click Uninstall.
Windows 8/Windows 8.1
a
Right-click (and hold) on TWAIN Driver for Epson Document
Camera Ver.X.XX, and then select Uninstall from the application
bar.
c
Select TWAIN Driver for Epson Document Camera Ver.X.XX, and
then select Uninstall.
Windows 10
Uninstalling
a
b
c
b
Turn on your computer.
The installer screen is automatically displayed.
d
47
Select Search from the Charm bar, and then search for TWAIN
Driver for Epson Document Camera Ver.X.XX.
a
b
c
d
Right click Start.
Click Control Panel.
Click Uninstall a program.
Select TWAIN Driver for Epson Document Camera Ver.X.XX, and
then click Uninstall.
Solving Problems
Problems and Solutions
Operation Problems
No image appears on the screen
• After you press the [t] power button, wait a few moments for the
image to appear. It takes approximately 15 seconds for the document
camera to output an image.
• Make sure all necessary cables are securely connected and the power is
on for the projector and the document camera.
s "Connecting the Document Camera Directly to a Projector" p.18
s "Connecting to a Projector Using a Computer" p.20
• If you have connected a laptop, see the following.
s "Problems Connecting a Laptop" p.50
• To project live images from the document camera, press the [Source] [ ] button on the document camera or the remote control.
• Select the correct source on your projector. The source refers to the
port on the projector to which you have connected the cable.
• Press the projector's power button to wake it from standby or sleep
mode. Make sure the image has not been "muted" or turned off. Also
see if your document camera is in sleep mode.
• If the power indicator on the document camera flashes, reconnect the
power cord. If no images are output even after pressing the [t] power
button again, stop using the document camera, contact your local dealer
or the nearest service center provided in this guide. s "Epson
Projector Contact List" p.51
Image Quality Problems
49
• Make sure the camera head is at least 10 cm (4 inches) away from the
object you are viewing.
• If you are using a projector to display the image, check its focus.
The image brightness or colors are incorrect
• To illuminate your document, slide the [
] lamp switch on the side
of the camera head.
• Press the [
] or [
] button to increase or decrease image brightness.
• Set the White Balance setting to Auto to adjust the color automatically.
If the colors are still not correct, select the best setting for the type of
lighting in your environment (Cloudy, Daylight, Fluorescent, or
Incandescent).
s "Image Menu" p.39
• If the document camera was used with a microscope, make sure you set
the Microscope setting to Off when you return to displaying
documents.
s "Image Menu" p.39
Other image problems
• If the image is stretched or has black bars, change the Output
Resolution or the HDMI Output from the Function menu.
s "Function Menu" p.40
a
To return all image settings to their initial values, select the Reset
menu.
s "Image Menu" p.39
The image is fuzzy or out of focus
• If the surroundings are dark and the contrast in the projected image is
low, the document camera's auto focus function may not work correctly.
Press the [ ] [ ] buttons on the document camera or the [Focus]
buttons [
manually.
] [
] on the remote control, and then adjust the contrast
SD Card Problems
Some images do not appear
Check the file format when copying images to the SD card from a
computer.
Problems and Solutions
• Images must be DCF-compliant, JPEG files to be displayed, such as
from a digital camera. Do not edit the images, as this may change their
format and prevent them from being displayed.
• Images must be named using the format ABCD1234.JPG, where ABCD
is any combination of upper- or lowercase letters and 1234 is any
combination of numbers. (For example: Pict0001, Pict0002)
• Images must be placed in a folder named DCIM\123ABCDE, where 123
is any combination of numbers and ABCDE is any combination of
upper- or lowercase letters. If this folder structure does not exist, first
create a folder named DCIM, then create a folder within it with the
desired name. (For example: 100EPSON)
Image files do not have the correct time stamp
The document camera does not have a built-in clock. Therefore, when you
view captured image files from your computer, the actual time they were
created is not displayed.
Problems Connecting a Laptop
If images are not displayed from a PC laptop, you need to set up the laptop
to display on an external monitor. If images are not displayed from a Mac
laptop, you need to set up the laptop for mirrored display. (See your laptop
manual for details.)
50
• Windows
Hold down the laptop's Fn key and press the key labeled with
or
CRT/LCD. (See your laptop manual for details.) Wait a few seconds for
an image to appear. To display on both the laptop's monitor and the
projector, try pressing the same keys again. If the same image is not
displayed by the laptop and projector, check the Windows Display
utility to make sure the external monitor port is enabled and extended
desktop mode is disabled. (See your computer or Windows manual for
instructions.)
• Mac
From the Apple menu, open the System Preferences utility and select
Displays. Click the Arrangement tab and select the Mirror Displays
checkbox.
Epson Projector Contact List
51
See the following contact list if any problems occur when using the
document camera outside Japan.
http://www.mrservis.hr
See the Web Home Page provided with each contact for the latest contact
information. If the country you are in is not provided, see the main home
page, www.epson.com.
CYPRUS
Mechatronic Ltd.
EUROPE
ALBANIA
ITD Sh.p.k.
http://www.itd-al.com
AUSTRIA
Epson Deutschland GmbH
http://www.epson.at
BELGIUM
Epson Europe B.V.
Branch office Belgium
http://www.epson.be
BOSNIA AND HERZEGOVINA
NET d.o.o. Computer Engineering
http://www.net.com.ba
BULGARIA
Epson Service Center, Bulgaria
http://www.kolbis.com
CROATIA
MR servis d.o.o.
http://www.mechatronic.com.cy
CZECH REPUBLIC
Epson Europe B.V.
Branch Office Czech Republic
http://www.epson.cz
DENMARK
Epson Denmark
http://www.epson.dk
ESTONIA
Epson Service Center, Estonia
http://www.epson.ee
FINLAND
Epson Finland
http://www.epson.fi
FRANCE and DOM-TOM TERRITORIES
Epson France S.A.
http://www.epson.fr
GERMANY
Epson Deutschland GmbH
http://www.epson.de
Epson Projector Contact List
52
GREECE
Oktabit S.A.
LUXEMBURG
Epson Europe B.V. Branch office Belgium
http://www.oktabit.gr
http://www.epson.be
HUNGARY
Epson Europe B.V.
Branch Office Hungary
MACEDONIA
Digit Computer Engineering
http://www.digit.com.mk
http://www.epson.hu
IRELAND
Epson (UK) Ltd.
NETHERLANDS
Epson Europe B.V. Benelux sales office
http://www.epson.nl
http://www.epson.ie
ISRAEL
Epson Israel
NORWAY
Epson Norway
http://www.epson.no
http://www.epson.co.il
ITALY
Epson Italia s.p.a.
POLAND
Epson EUROPE B.V. Branch Office Poland
http://www.epson.pl
http://www.epson.it
KAZAKHSTAN
Epson Kazakhstan Rep. Office
PORTUGAL
Epson Ibérica S.A.U. Branch Office Portugal
http://www.epson.pt
http://www.epson.kz
LATVIA
Epson Service Center, Latvia
ROMANIA
Epson Europe B.V. Branch Office Romania
http://www.epson.ro
http://www.epson.lv
LITHUANIA
Epson Service Center Lithuania
http://www.epson.lt
RUSSIA
Epson CIS
http://www.epson.ru
Epson Projector Contact List
53
UKRAINE
Epson Kiev Rep Office
UK
Epson (UK) Ltd.
http://www.epson.ua
http://www.epson.co.uk
SERBIA
AVG d.o.o. Beograd
http://www.a-v-g.rs
SLOVAKIA
Epson EUROPE B.V. Branch Office Czech Republic
Indication of the manufacturer and the importer in accordance with
requirements of EU directive
Manufacturer: SEIKO EPSON CORPORATION
Address: 3-5, Owa 3-chome, Suwa-shi, Nagano-ken 392-8502 Japan
Telephone: 81-266-52-3131
http://www.epson.com/
http://www.epson.sk
SLOVENIA
Birotehna d.o.o
http://www.birotehna.si
Importer: EPSON EUROPE B.V.
Address: Atlas Arena, Asia Building, Hoogoorddreef 5,1101 BA Amsterdam Zuidoost
The Netherlands
Telephone: 31-20-314-5000
http://www.epson.com/europe.html
SPAIN
Epson Ibérica, S.A.U.
http://www.epson.es
SWEDEN
Epson Sweden
http://www.epson.se
SWITZERLAND
Epson Deutschland GmbH Branch office Switzerland
http://www.epson.ch
TURKEY
Tecpro Bilgi Teknolojileri Tic. ve San. Ltd. Sti.
http://www.tecpro.com.tr
AFRICA
http://www.epson.co.za or http://www.epson.fr
SOUTH AFRICA
Epson South Africa
http://www.epson.co.za
MIDDLE EAST
Epson (Middle East)
http://www.epson.ae
Epson Projector Contact List
NORTH, CENTRAL AMERICA & CARIBBEAN
ISLANDS
CANADA
Epson Canada, Ltd.
http://www.epson.ca
COSTA RICA
Epson Costa Rica, S.A.
http://www.epson.co.cr
MEXICO
Epson Mexico, S.A. de C.V.
http://www.epson.com.mx
ECUADOR
Epson Ecuador
http://www.epson.com.ec
U.S.A.
Epson America, Inc.
54
http://www.epson.com.ar
BRAZIL
Epson do Brasil
http://www.epson.com.br
CHILE
Epson Chile S.A.
http://www.epson.cl
COLOMBIA
Epson Colombia Ltd.
http://www.epson.com.co
PERU
Epson Peru S.A.
http://www.epson.com.pe
VENEZUELA
Epson Venezuela S.A.
http://www.epson.com.ve
http://www.epson.com
ASIA AND OCEANIA
SOUTH AMERICA
ARGENTINA
Epson Argentina S.R.L.
AUSTRALIA
Epson Australia Pty. Ltd.
http://www.epson.com.au
CHINA
Epson (CHINA) CO., Ltd.
Epson Projector Contact List
55
http://www.epson.com.cn
PHILIPPINES
Epson Philippines Co.
HONG KONG
Epson Hong Kong Ltd.
http://www.epson.com.ph
http://www.epson.com.hk
SINGAPORE
Epson Singapore Pte. Ltd.
INDIA
Epson India Pvt., Ltd.
http://www.epson.com.sg
http://www.epson.co.in
TAIWAN
Epson Taiwan
Technology & Trading Ltd.
INDONESIA
PT. Epson Indonesia
http://www.epson.com.tw
http://www.epson.co.id
JAPAN
SEIKO EPSON CORPORATION
TOYOSHINA OFFICE
http://www.epson.jp
KOREA
Epson Korea Co., Ltd.
http://www.epson.co.kr
MALAYSIA
Epson Malaysia Sdn. Bhd.
http://www.epson.com.my
NEW ZEALAND
Epson New Zealand
http://www.epson.co.nz
THAILAND
Epson (Thailand) Co., Ltd.
http://www.epson.co.th
Notices
Specifications
57
General Specifications
ELPDC13
Product name
Open (W ^ D ^ H): 270 ^ 317 ^ 447 mm (10.6 ^ 12.5 ^ 17.6 inches)
Folded (W ^ D ^ H): 367 ^ 122 ^ 120 mm (14.4 ^ 4.8 ^ 4.7 inches)
Dimensions
1/2.7 inch CMOS sensor
Type of sensor
F=2.8
Lens
2 megapixel (1920 ^ 1080)
Effective pixels
1080p: Maximum 30.7 ^ 54.8 cm (12.0 ^ 21.5 inches)
XGA: Maximum 30.7 ^ 41.1 cm (12.0 ^ 16.1 inches)
Imaging area
Focus adjustment
Automatic/manual
Zoom adjustment
16x digital zoom
Up to 30 fps
Frame rate
1 (monaural input)
Internal microphone
Power supply
AC adapter
Main unit
Power consumption
100to 240 VAC ±10%, 50/60 Hz
12 VDC
Operating: 13 W
Standby: 0.2 W
Operating temperature
+5 to +35C, without condensation
Storage temperature
-10 to +60C, without condensation
Operating humidity
20 to 80% RH, without condensation
Storage humidity
10 to 90% RH, without condensation
Weight
Approx. 2.8 kg (6.2 lb)
Specifications
58
Input port
Computer In port
1
Mini D-Sub15-pin (female)
Output port
Display Out port
1
Mini D-Sub15-pin (female)
Output: SXGA (1280 x 1024)/XGA (1024 x 768)/WXGA (1280 x 800)/HD (1360 x 768)/1080p
(1920 x 1080)
HDMI port *1
1
HDMI
Output: SDTV (480p)/HDTV (720p, 1080p)
USB-B port *2
1
USB connector (TypeB)
Output: VGA/SVGA/XGA/SXGA/WXGA/720p/1080p
SD card slot
1
SD/SDHC card compatible
Connector port
*1 HDMI CEC is supported, however, the operation of all compatible devices is not guaranteed.
*2 USB 2.0 is supported, however, the operation of all USB compatible devices is not guaranteed.
This product is also designed for IT power distribution system with phase-to-phase voltage 230V.
Symbols Indicating the Device Meets the IEC60950-1 A2 Safety Standards
The following table lists the meaning of the safety symbols labeled on the
equipment.
No.
Symbol mark
Approved
standards
Meaning
A
IEC60417
No.5007
"ON" (power)
To indicate connection to the mains.
B
IEC60417
No.5008
"OFF" (power)
To indicate disconnection from the mains.
C
IEC60417
No.5009
Stand-by
To identify the switch or switch position
by means of which part of the equipment is
switched on in order to bring it into the
stand-by condition.
ISO7000
No.0434B
IEC3864-B3.1
Caution
To identify general caution when using the
product.
IEC60417
No.5041
Caution, hot surface
To indicate that the marked item can be
hot and should not be touched without
taking care.
D
E
F
IEC60417
No.6042
ISO3864-B3.6
Caution, risk of electric shock
To identify equipment that has risk of
electric shock.
G
IEC60417
No.5957
For indoor use only
To identify electrical equipment designed
primarily for indoor use.
H
IEC60417
No.5926
Polarity of d.c. power connector
To identify the positive and negative
connections (the polarity) on a piece of
equipment to which a d.c. power supply
may be connected.
No.
Symbol mark
Approved
standards
59
Meaning
I
IEC60417
No.5001B
Battery, general
On battery powered equipment. To
identify a device for instance a cover for
the battery compartment, or the
connector terminals.
J
IEC60417
No.5002
Positioning of cell
To identify the battery holder itself and to
identify the positioning of the cell(s)
inside the battery holder.
K
IEC60417
No.5019
Protective earth
To identify any terminal which is intended
for connection to an external conductor
for protection against electric shock in
case of a fault, or the terminal of a
protective earth electrode.
L
IEC60417
No.5017
Earth
Indicates a grounding port when No. 11 is
not explicitly called for.
M
IEC60417
No.5032
Alternating current
To indicate on the rating plate that the
equipment is suitable for alternating
current only; to identify relevant
terminals.
N
IEC60417
No.5031
Direct current
To indicate on the rating plate that the
equipment is suitable for direct current
only; to identify relevant terminals.
O
IEC60417
No.5172
Class II equipment
To identify equipment meeting the safety
requirements specified for Class II
equipment according to IEC 61140.
P
ISO 3864
General prohibition
To identify actions or operations that are
prohibited.
Symbols Indicating the Device Meets the IEC60950-1 A2 Safety Standards
No.
Symbol mark
Approved
standards
Meaning
Q
ISO 3864
Contact prohibition
To indicate injury that could occur due to
touching a specific part of the equipment.
R
---
Never look into the optical lens while the
projector is on.
S
---
To indicate that the marked item don't
place anything on projector.
T
ISO3864
IEC60825-1
Caution, laser radiation
To indicate the equipment has a laser
radiation part.
U
ISO 3864
Disassembly prohibition
To indicate a risk of injury, such as electric
shock, if the equipment is disassembled.
V
---
Indicates that you should not look into the
lens while the LED is on.
60
General Notice
61
DECLARATION of CONFORMITY
According to 47CFR, Part 2 and 15
Class B Personal Computers and Peripherals; and/or
CPU Boards and Power Supplies used with Class B Personal Computers
We:
Located at:
Tel:
Epson America, Inc.
3840 Kilroy Airport Way
MS: 3-13
Long Beach, CA 90806
562-981-3840
Declare under sole responsibility that the product identified herein,
complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital
device. Each product marketed, is identical to the representative unit tested
and found to be compliant with the standards. Records maintained continue
to reflect the equipment being produced can be expected to be within the
variation accepted, due to quantity production and testing on a statistical
basis as required by 47CFR 2.909. Operation is subject to the following two
conditions : (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that
may cause undesired operation.
Trade Name:
Type of Product:
Model:
EPSON
Document Camera
ELPDC13/ELPDC21
FCC Compliance Statement
For United States Users
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause interference to radio
and television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this
equipment will invalidate the FCC Certification or Declaration of this
device and may cause interference levels which exceed the limits established
by the FCC for this equipment. It is the responsibility of the user to obtain
and use a shielded equipment interface cable with this device. If this
equipment has more than one interface connector, do not leave cables
connected to unused interfaces. Changes or modifications not expressly
approved by the manufacturer could void the user's authority to operate the
equipment.
For Canadian Users
Copyrights and Trademarks
All rights reserved. No part of this publication may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written permission of Seiko
Epson Corporation. No patent liability is assumed with respect to the use of the
information contained herein. Neither is any liability assumed for damages resulting
from the use of the information contained herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this
product or third parties for damages, losses, costs, or expenses incurred by the
purchaser or third parties as a result of: accident, misuse, or abuse of this product or
unauthorized modifications, repairs, or alterations to this product, or (excluding the
U.S.) failure to strictly comply with Seiko Epson Corporation's operating and
maintenance instructions.
Seiko Epson Corporation shall not be liable against any damages or problems arising
from the use of any options or any consumable products other than those designated as
Original Epson Products or Epson Approved Products by Seiko Epson Corporation.
The contents of this guide may be changed or updated without further notice.
Illustrations in this guide and the actual projector may differ.
Responsible Use of Copyrighted Materials
Epson encourages each user to be responsible and respectful of the
copyright laws when using any Epson product. While some countries' laws
permit limited copying or reuse of copyrighted material in certain
circumstances, those circumstances may not be as broad as some people
assume. Contact your legal advisor for any questions regarding copyright
law.
Trademarks
Mac, OS X and macOS are registered trademarks of Apple Inc.
62
Microsoft, Windows, Windows Vista, and the Windows logo are trademarks
or registered trademarks of Microsoft Corporation in the United States
and/or other countries.
SDHC Logo is a trademark of SD-3C, LLC.
HDMI and High-Definition Multimedia Interface are the trademarks or
registered trademarks of HDMI Licensing LLC.
Other product names used herein are for identification purposes only and
may be trademarks of their respective owners. Epson disclaims any and all
rights in those marks.
This information is subject to change without notice.
© SEIKO EPSON CORPORATION 2017. All rights reserved.
">