®

OWNER’S MANUAL

Outdoor Patio Heater

Model No. 235000

DANGER

CARBON MONOXIDE HAZARD

• This appliance can produce carbon monoxide which has no odor.

• Using it in an enclosed space can kill you.

• Never use this appliance in an enclosed space such as a camper, tent, car or home.

WARNING

FOR YOUR SAFETY:

For Outdoor Use Only

(outside any enclosure)

WARNING

FOR YOUR SAFETY:

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage.

Read the installation, operation, and maintenance instructions thoroughly before installing or servicing this equipment.

Failure to follow these instructions could result in fire or explosion, which could cause property damage, personal injury, or death.

Made from 70% Bagasse

(Environmentally Friendly Sugar

Cane Pulp By-product)

Table of Contents

Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2

Exploded View & Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Assembly Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Installling LP Gas Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Insert LP Gas Tank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Secure LP Gas Tank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Connect LP Gas Tank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Disconnect LP Gas Tank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Operating Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Checking for Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Before Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Lighting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

When heater is ON. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Re-Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Cleaning Surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Product Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Other Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

The use and installation of this product must conform to local codes. In absence of local codes, use the National Fuel Gas Code, ANSI Z223.1/NFPA 54, CAN/CGA-B149.1, Natural Gas and

Propane Installation Code.

California Proposition 65: Chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm are created by the combustion of propane.

Save these instructions for future reference. If you are assembling this unit for someone else, give this manual to him or her to read and save for future reference.

Manufactured in China for:

Blue Rhino Global Sourcing, Inc

Winston-Salem, NC 27105 USA

1.800.762.1142, www.bluerhino.com

© 2007 Blue Rhino Global Sourcing, Inc. All Rights Reserved

Endless Summer

®

is a Registered Trademark of Blue Rhino Global Sourcing, Inc. All Rights Reserved

U.S. Patent Number: 6,6102,031; 6,470,877; Hong Kong Patent Number: 1108587.1; All Other Foreign Patents May Apply.

235000-OM-112 E

®

Outdoor Patio Heater Model No. 235000

DANGERS and WARNINGS: FOR YOUR SAFETY

If you smell gas -

1. Shut off gas to appliance.

2. Extinguish any open flame.

DANGER

3. If odor continues, immediately call your gas supplier or your fire department.

WARNING

FOR YOUR SAFETY

1. Do not store spare LP cylinder within 10 feet (3.05 m) of this appliance.

2. Do not store or use gasoline or other flammable vapors and liquids within 25 feet (7.62 m) of this or any other appliance.

3. An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.

DANGER: Failure to follow the dangers, warning and cautions in this manual may result in serious bodily injury or death, or in a fire or an explosion causing damage to property.

WARNING:

This heater is for outdoor use only, and shall not be used in a building, garage, or any other enclosed area.

Always maintain at least 36” clearance (top), and 24” clearance (side) from combustible materials.

This heater is for use with liquid propane (LP) gas only. The conversion to or attempted use of natural gas in this LP gas heater is dangerous and will void your warranty.

LP gas Characteristics: a. LP gas is flammable and hazardous if handled improperly. Become aware of the characteristics before using any LP gas product. b. LP gas is explosive under pressure, heavier than air, and settles and pools in low areas. c. LP gas in its natural state has no odor. For your safety, an odorant is added that smells like rotten cabbage. d. Contact with LP gas can cause freeze burns to skin.

LP gas tank needed to operate. Only tanks marked “propane” may be used.

The LP gas supply tank must be constructed and marked in accordance with the Specifications for LP gas Cylinders of the U.S. Department of

Transportation (DOT) or the National Standard of Canada, CAN/CSA-

B339, Cylinders, Spheres and Tubes for the Transportation of Dangerous

Goods; and Commission.

LP gas tank must be arranged for vapor withdrawal.

The LP gas tank must have a listed overfilling prevention device (OPD).

Only use 20-pound cylinders equipped with a cylinder connection device compatible with the connection for outdoor cooking appliances.

The LP gas tank must have a tank collar to protect the tank valve.

Never use an LP gas tank with a damaged body, valve, collar, or footing.

Dented or rusted LP gas tanks may be hazardous and should be checked by your LP gas supplier prior to use.

The LP gas tank should not be dropped or handled roughly.

Tanks must be stored outdoors out of the reach of children and must not be stored in a building, garage, or any other enclosed area. Your tank must never be stored where temperatures can reach over 125°F.

Never keep a filled LP gas tank in a hot car or car trunk. Heat will cause the gas pressure to increase, which may open the relief valve and allow gas to escape.

Do not store a spare LP gas tank under or near this appliance.

Never fill the tank beyond 80 percent full.

Never attempt to attach this heater to the self-contained LP gas system of a camper trailer, motor home, or house.

The use of alcohol, or prescription or non-prescription drugs may impair the consumer’s ability to properly assemble or safely operate the appliance.

Your heater has been checked at all factory connections for leaks.

Recheck all connections, as movement in shipping can loosen connections.

Check for leaks even if your unit was assembled for you by someone else.

Do not operate if gas leak is present. Gas leaks may cause a fire or explosion.

You must follow all leak-checking procedures before operating. To prevent fire or explosion hazard when testing for a leak: a. Always perform leak test before lighting the heater and each time the tank is connected for use.

b. No smoking. Do not use or permit sources of ignition in the area while conducting a leak test. c. Conduct the leak test outdoors in a well-ventilated area. d. Do not use matches, lighters, or a flame to check for leaks. e. Do not use heater until any and all leaks are corrected.

If you are unable to stop a leak, disconnect the LP gas supply. Call a gas appliance serviceman or your local LP gas supplier.

Do not store or use gasoline or other flammable liquids or vapors within

25 feet (7.62 m) of this appliance.

Do not use in an explosive atmosphere. Keep heater area clear and free from combustible materials, gasoline and other flammable vapors and liquids.

Keep all combustible items and surfaces away from the heater at all times. DO NOT use this heater or any gas product under any overhead or near any unprotected combustible constructions.

Combustion of propane creates carbon monoxide, which, when used in enclosed areas, can kill you.

It is essential to keep the heater’s valve compartment, burners, and circulating air passages clean. Inspect heater before each use.

Installation and repair should be done by a qualified service person.

Do not alter heater in any manner.

Do not use the heater unless it is COMPLETELY assembled and all parts are securely fastened and tightened.

This heater should be thoroughly inspected before each use. Clean and inspect the hose before each use of the appliance. If there is evidence of abrasion, wear, cuts, or leaks, the hose must be replaced prior to the appliance being put into operation.

Use only the regulator and hose assembly provided. The replacement regulator and hose assembly shall be that specified by the manufacturer.

Inspect heater before each use. If a damaged part is detected, do not operate until an original equipment replacement part has been properly installed.

Use only Blue Rhino Global Sourcing, Inc. factory authorized parts. The use of any part that is not factory authorized can be dangerous. This will also void your warranty.

Dome and burner are extremely hot to the touch during operation. Never touch the dome or burner while the heater is operating. Wait for unit to cool down (approximately 45 minutes) after use.

During operation, do not touch burner assembly. The surface of heater’s emitter can reach temperatures approaching 1600ºF.

Do not install or use in or on boats or recreational vehicles.

Do not use heater in winds that exceed 10 m.p.h..

Unit will operate at reduced efficiency below 40ºF (5ºC).

Do not leave a lit heater unattended, especially keep children and pets away from heater at all times.

Always use extreme caution when near heater. Alert both children and adults to the hazards of high temperatures, especially to avoid burns or clothing catching fire.

Do not attempt to move heater when in use. Allow the heater to cool before moving or storing.

Storage of heater indoors is permissible only if the tank is disconnected, removed from the heater and properly stored outdoors.

Do not attempt to disconnect the gas regulator from the tank or any gas fitting while the heater is in use.

Always place your heater on a hard, level surface.

Use extreme caution on wooden decks.

Move gas hoses as far away as possible from hot surfaces.

Keep all electrical cords away from a hot heater.

Do not use heater for indoor cooking or heating. TOXIC fumes can accumulate and cause asphyxiation.

Keep sprinklers and other water sources away from burner and controls.

Do not hang clothing or other flammable materials either on or near heater.

Always allow heater to cool before attempting service.

Any guard or other protective device removed for servicing the heater must be replaced prior to operating the heater.

Certain materials or items, when stored under heater, will be subjected to radiant heat and could be seriously damaged.

After a period of storage and/or nonuse, check for leaks, burner obstructions and inspect for any abrasion, wear, cuts to the hose.

If at any time you are unable to light burner and smell gas, wait 5 minutes to allow gas to dissipate before attempting to light heater.

Failure to not wait 5 minutes to allow the gas to clear if the heater does not light, may result in an explosive flame-up.

Be careful when attempting to manually ignite this heater. Holding in the control knob for more than 10 seconds before igniting the gas will cause a ball of flame upon ignition.

Avoid inhaling fumes emitted from the heater’s first use. Smoke and odor from the burning of oils used in manufacturing will appear. Both smoke and odor will dissipate after approximately 30 minutes. The heater should NOT produce thick black smoke.

If heater is not in use, the gas must be turned off at the supply tank.

Do not use this appliance without reading “Operating Instructions” in this manual.

Deaths, serious injury or damage to property may occur if the above is not followed exactly.

Contact 1.800.762.1142 for assistance. Do not return to place of purchase.

Outdoor Patio Heater Model No. 235000 Contact 1.800.762.1142 for assistance. Do not return to place of purchase.

Parts List

1 Large Dome

2 Medium Dome

3 Small Dome

4 Insulation Cone*

5 Emitter Screen*

6 Burner*

7 Pilot Heat Shield*

8 Pilot Assembly*

9 Burner Orifice*

10 Electronic Igniter*

11 Igniter Button*

12 Control Knob*

13 Access Panel*

14 Valve*

15 Valve bracket*

16 Tip Switch*

17 Valve Housing*

18 Gas Line

56-01-309

56-01-257

56-01-258

56-01-114

56-01-113

56-01-334

56-01-151

56-01-127

56-01-131

56-01-142

56-01-188

56-01-156

56-01-140

56-01-144

56-01-148

56-01-019

56-01-146

56-01-190

19 Pole

20 Platform Cover

21 Shroud

56-01-340

56-01-403

56-01-164

22 Platform

23 Gas Line Clip

56-01-165

56-01-213

24 Leg (3) 56-01-193

25 Regulator/Hose Assembly 56-01-192

26 Tank Retention Chain

27 Wheel Hole Plug (2)

28 Base

29 Weight Plate

* Pre Assembled

56-01-186

56-01-402

56-01-196

56-01-384

Exploded View

22

2

27

25

1

4

3

5

6

7

17

18

20

19 16

15

14

8

9

10

13

11

12

21

23

24

26

28

29

Hardware

A

Screw

B

Screw

C Bolt

D

Bolt

E

Bolt

F

Nut

1/4” - 20 x 10 Stainless Steel Round Head

1/4” - 20 x 10 Nickel Plated Philips Head

5/32” - 32 x 8 Stainless Steel Hex Head Bolt

1/4” - 20 x 20 Nickel Plated Head Bolt

3/8” - 16 x 95 Nickel Plated Hex Head Bolt

1/4” - 20 Nickel Plated Hex Nut

G Nut

H

Nut

3/8” - 16 Stainless Steel Hex Nut

3/8” - 16 Nickel Plated Cap Nut

I

Lock Washer ø6 Nickel Plated Lock Washer

J Lock Washer ø10 Nickel Plated Lock Washer

K

Battery AA Battery

4 pcs

1 pc

6 pcs

12 pcs

1 pc

12 pcs

1 pc

3 pcs

12 pcs

1 pc

1 pc

Tools Required for Assembly (Not Included)

7/16” Wrench

9/16” Wrench

3/4” Wrench

7/16” Socket and Socket Wrench

7/16"

#2 Phillips Head Screwdriver page no.

3

®

Outdoor Patio Heater Model No. 235000

Assembly Instructions

1

DO NOT RETURN PRODUCT TO STORE.

For assistance call 1.800.762.1142 toll free. Please have your owner’s manual and serial number available for reference.

For Easiest Assembly:

• To avoid losing any small components or hardware, assemble your product on a hard level surface that does not have cracks or openings.

• Clear an area large enough to layout all components and hardware.

• When applicable, tighten all hardware connections by hand first. Once the step is completed go back and fully tighten all hardware.

• Follow all steps in order to properly assemble your product.

To complete assembly you will need:

• (1) Leak Detection Solution (Instructions on how to make solution are included in step Operations Section)

• (1) Precision Filled LP Gas Grill Tank with Acme Type 1 external threaded valve connection (4-5 gallon size)

Note: You must follow all steps to properly assemble heater.

Typical assembly: approximately 1 (one) hour.

2

Attach Legs and Tank Retention Chain

x 6 x 6

I x 6 D

F

3

Attach weight plate

Note: If you plan to anchor your heater permanently, be sure to line up two outer holes in base with those in weight plate so that your anchor bolt will pass through both holes.

4

Attach Platform

TIP: To tighten use a 7/16” wrench on Bolt and a 7/16” socket wrench on Nut.

Contact 1.800.762.1142 for assistance. Do not return to place of purchase.

E

G x 1 x 1

J x 1

D x 6

F x 6

I x 6

Assembly Instructions

Outdoor Patio Heater Model No. 235000 Contact 1.800.762.1142 for assistance. Do not return to place of purchase.

5

Insert Gas Line and Shroud

6

Attach Medium Dome and Small Dome

page no.

5 x 6

C

7

Attach Engine Assembly

Note: Make sure gas line comes out bottom of pole before securing engine to pole.

8

Attach Platform Cover and Post

Note: Secure setscrews in platform and tighten bottom screws then top screws.

Note: Post MUST BE straight (perpendicular to base). Failure to do so will adversely affect burner performance.

A x 4

Assembly Instructions (continued)

9

Attach Gas Line

®

11

Attach Dome Assembly

Outdoor Patio Heater Model No. 235000

10

Attach Gas Line Clip

Side View

B

Gas Line Clip

Bottom View

Gas Line

x 1

B

12

Attach Control Knob

Contact 1.800.762.1142 for assistance. Do not return to place of purchase.

H x 3

Assembly Instructions (continued)

Outdoor Patio Heater Model No. 235000

13

Insert Battery

Contact 1.800.762.1142 for assistance. Do not return to place of purchase.

page no.

7

Installing LP Gas Tank

To operate you will need (1) precision-filled standard grill LP gas tank (20 lbs.) with external valve threads.

Note: An empty standard grill LP gas tank weighs approximately

18 lbs. A precision-filled standard grill LP gas tank should weigh no more than 38 lbs.

Insert LP Gas Tank

Place precision filled LP gas tank upright into hole in patio heater so it is arranged for vapor withdrawal.

Secure LP Gas Tank

Secure tank in place by attaching loose end of tank restraint chain to hole in right leg.

K x 1

Connect LP Gas Tank

Before connecting, be sure that there is no debris caught in the head of the LP gas tank, head of the regulator valve or in the head of the burner and burner ports.

Connect gas line to tank by turning knob clockwise until it stops.

Disconnect LP Gas Tank

Before disconnecting make sure the LP gas tank valve OFF.

Disconnect gas line to tank by turning knob counterclockwise until it is loose.

Need a tank of gas? Try tank exchange service. It’s easy, fast, safe, and available at tens of thousands of conveniently located retail outlets nationwide. You can purchase a new full tank or exchange your empty for a precision filled one.

®

Outdoor Patio Heater Model No. 235000

Operating Instructions

Checking for Leaks

Burner Connections

Make sure the regulator valve and hose connections are securely fastened to the burner and the tank.

If your unit was assembled for you, visually check the connection between the burner pipe and orifice. Make sure the burner pipe fits over the orifice.

WARNING: Failure to inspect this connection or follow these instructions could cause a fire or an explosion which can cause death, serious bodily injury, or damage to property.

If the burner pipe does not rest flush to the orifice, please contact 1.800.762.1142 for assistance.

Have a question or are having problems visit www.bluerhino.com or call 1.800.762.1142.

Note: the burner may be noisy when initially turned on. To eliminate excessive noise from the burner, turn the control knob to the pilot position. Then, turn the knob to the level of heat desired.

When heater is ON:

Emitter screen will become bright red due to intense heat. The color is more visible at night.

Burner will display tongues of blue and yellow flame. These flames should not be yellow or produce thick black smoke, indicating an obstruction of airflow through the burners. The flame should be blue with straight yellow tops.

If excessive yellow flame is detected, turn off heater and visit www.bluerhino.com or call

1.800.762.1142.

Tank/Gas Line Connection

Make 2-3 oz. of leak solution by mixing one part liquid dishwashing soap with three parts water.

Make sure control knobs are “OFF”.

Turn LP gas tank “ON” at valve.

Spoon leak check solution at all “X” locations

If any bubbles appear turn LP gas tank “OFF”, reconnect and re-test. If you continue to see bubbles after several attempts, disconnect LP gas source and contact

1.800.762.1142 for assistance.

If no bubbles appear after one minute turn tank “OFF”, wipe away solution and proceed.

Before Lighting

Heater should be thoroughly inspected before each use, and by a qualified service person at least annually.

If relighting a hot heater, always wait at least 5 minutes.

Inspect the hose assembly for evidence of excessive abrasion, cuts, or wear. Suspected areas should be leak tested. If the hose leaks, it must be replaced prior to operation. Only use the replacement hose assembly specified by manufacturer.

X

X

X

LP Gas Line

X

X

X

LP Gas Tank Valve

Lighting

Note: this heater is equipped with a pilot light that allows for safer startups and shutdowns.

Pilot must be lit before main burner can be started.

1. Turn tank valve “OFF”.

2. Push control knob in and turn to “OFF”.

View Hole

3. Wait 5 minutes for any gas to clear.

4. Turn tank valve “ON”.

5. Open viewing hole by sliding cover to either side.

6. Push control knob in and rotate to pilot position.

Note: for initial start or after any tank change, hold control knob in for 2 minutes to purge air from gas lines before proceeding.

7. Push igniter button once. Pilot light flame will appear and be visible through viewing hole.

8. Release control knob after 30 seconds.

Pilot light will remain lit. If not, return to step 1.

9. Turn control knob to “HIGH”. Main burner will light immediately. Flame is visible through viewing hole. If not, return to step 1.

10. If for some reason your ignitor fails to deliver a spark, your heater can be started by inserting a lit match through the pilot view hole while pushing the control knob in while in the pilot position.

WARNING: Be careful when attempting to manually ignite this heater. Holding in the control know for more than 10 seconds before igniting the gas will cause a ball of flame upon ignition.

Pilot

(Push in)

(Push in)

Control Knob

Re-lighting

Note: For your safety, control knob cannot be turned

“OFF” without first depressing control knob in PILOT position and then rotating it to “OFF”.

1. Turn control knob to “OFF”.

2. Wait at least 5 minutes, to let gas dissipate, before attempting to relight pilot.

3. Repeat the “Lighting” steps.

Proper flame height.

Shut Down

1. Turn control knob clockwise to pilot. (Normally, burner will make a slight popping sound when extinguished.) Burner will extinguish but pilot will remain “ON”.

2. To extinguish pilot, depress control knob and continue to turn it clockwise to “OFF”.

3. Turn tank valve clockwise to “OFF” and disconnect regulator when heater is not in use.

Note: After use, some discoloration of the emitter screen is normal.

Cleaning and Care

CAUTION: All cleaning and maintenance should be done when patio heater is cool and with the fuel supply disconnected.

CAUTION: DO NOT clean any patio heater part in a self cleaning oven.

The extreme heat will damage the finish.

Notices

1. Abrasive cleaners will damage this product.

2. Never use oven cleaner to clean any part of heater.

3. Do not clean any heater part in a self cleaning oven. The extreme heat will damage the finish.

4. More frequent cleaning may be required as necessary. It is imperative that control compartment, burners and circulating air passageways of the heater be kept clean.

5. Spiders and insects can create a dangerous condition that may damage heater or make it unsafe. Keep burner area clean of all spiders, webs, or insects. Clean burner holes by using a heavy-duty pipe cleaner. Compressed air may help clear away smaller particles.

6. Inspect heater before each use.

7. Have heater inspected annually and repairs should be made by a qualified service person.

8. Check heater immediately if any of the following conditions exist: a. The smell of gas in conjunction with extreme yellow tipping of burner flames.

b. Heater does not reach proper temperature.

Note: At temperatures less than 40ºF, heat output will be reduced.

c. Heater’s glow is excessively uneven d. Burner makes popping noises during use.

Note: A slight pop is normal when burner is extinguished.

9. Carbon deposits may create a fire hazard. Keep dome and emitter clean at all times.

10. Do not clean heater with combustible or corrosive cleaners. Use warm, soapy water.

11. Do not paint engine, engine access panel or dome.

12. This heater should be thoroughly cleaned on a regular basis.

13. After a period of storage and/or nonuse, check for leaks, burner obstructions and inspect for any abrasion, wear, cuts to the hose.

Contact 1.800.762.1142 for assistance. Do not return to place of purchase.

Outdoor Patio Heater Model No. 235000 Contact 1.800.762.1142 for assistance. Do not return to place of purchase.

page no.

9

Cleaning and Care (continued)

Cleaning Surfaces

1. Wipe surfaces clean with mild dishwashing detergent or baking soda.

2. For stubborn surfaces use a citrus based degreaser and a nylon scrubbing brush.

3. Rinse clean with water.

Note: While cleaning your unit, be sure to keep the area around the burner and pilot assembly dry at all times. Do not submerge the control valve assembly. If the gas control is submerged in water, do NOT use it. It must be replaced.

Maintenance

To enjoy years of outstanding performance from your heater, make sure you perform the following maintenance activities on a regular basis:

1. Keep exterior surfaces clean.

2. Air flow must be unobstructed. Keep controls, burner, and circulating air passageways clean.

Signs of possible blockage include:

Gas odor with extreme yellow tipping of flame.

Heater does NOT reach the desired temperature.

Heater glow is excessively uneven.

Heater makes popping noises.

Note: In a salt-air environment (such as near an ocean), corrosion occurs more quickly than normal. Frequently check for corroded areas and repair them promptly.

TIP: Use high-quality automobile wax to help maintain the appearance of your heater. Apply to exterior surfaces from the pole down. Do not apply to emitter screen or domes.

Storage

Between uses:

1. Turn Control Knob OFF.

2. Disconnect LP source.

3. Store heater upright in an area sheltered from direct contact with inclement weather (such as rain, sleet, hail, snow, dust and debris).

4. If desired, cover heater to protect exterior surfaces and to help prevent build up in air passages.

Note: Wait until heater is cool before covering.

Product Registration

For faster warranty service, please register your product immediately at www.bluerhino.com or call 1.800.762.1142.

Limited Warranty

Blue Rhino Global Sourcing, Inc (“Vendor”) warrants to the original retail purchaser of this product, and to no other person, that if this product is assembled and operated in accordance with the printed instructions accompanying it, then for a period of two (2) years for the burners; and one (1) year for all remaining parts from the date of purchase, all parts in such product shall be free from defects in material and workmanship. Vendor may require reasonable proof of your date of purchase. Therefore, you should retain your sales slip or invoice. This Limited Warranty shall be limited to the repair or replacement of parts, which prove defective under normal use and service and which Vendor shall determine in its reasonable discretion upon examination to be defective. Before returning any parts, you should contact Vendor’s Customer Service Department using the contact information listed below. If

Vendor confirms, after examination, a defect covered by this Limited Warranty in any returned part, and if Vendor approves the claim, Vendor will replace such defective part without charge.

If you return defective parts, transportation charges must be prepaid by you. Vendor will return replacement parts to the original retail purchaser, freight or postage prepaid.

This Limited Warranty does not cover any failures or operating difficulties due to accident, abuse, misuse, alteration, misapplication, improper installation or improper maintenance or service by you or any third party, or failure to perform normal and routine maintenance on the product as set out in this owner’s manual. In addition, the Limited Warranty does not cover damage to the finish, such as scratches, dents, discoloration, rust or other weather damage, after purchase.

This Limited Warranty is in lieu of all other express warranties. Vendor disclaims all warranties for products that are purchased from sellers other than authorized retailers or distributors, including the warranty of merchantability or the warranty of fitness for a particular purpose. VENDOR ALSO DISCLAIMS AND ANY ALL IMPLIED WARRANTIES, INCLUDING

WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR

A PARTICULAR PURPOSE. VENDOR SHALL HAVE NO LIABILITY TO PURCHASER OR ANY THIRD

PARTY FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

Vendor further disclaims any implied or express warranty of, and assumes no responsibility for, defects in workmanship caused by third parties.

This Limited Warranty gives the purchaser specific legal rights; a purchaser may have other rights depending upon where he or she lives. Some jurisdictions do not allow the exclusion or limitation of special, incidental or consequential damages, or limitations on how long a warranty lasts, so the above exclusion and limitations may not apply to everyone.

Vendor does not authorize any person or company to assume for it any other obligation or liability in connection with the sale, installation, use, removal, return, or replacement of its equipment, and no such representations are binding on Vendor.

Blue Rhino Global Sourcing, Inc

Winston-Salem, North Carolina 27105 USA

(800) 762-1142

During periods of extended inactivity or when transporting:

1. Turn Control Knob “OFF”.

2. Disconnect LP source and move to a secure, well-ventilated location outdoors.

3. Store heater upright in an area sheltered from direct contact with inclement weather (such as rain, sleet, hail, snow, dust and debris).

4. If desired, cover heater to protect exterior surfaces and to help prevent build up in air passages.

5. Never leave LP tank exposed to direct sunlight or excessive heat.

Note: Wait until heater is cool before covering.

®

Outdoor Patio Heater Model No. 235000

Troubleshooting

If the problem is:

Pilot won’t light

And this condition exists:

Tank valve is closed

Then do this

Open valve

Note: Heater operates at reduced efficiency below 40ºF (5ºC).

Pilot won’t stay lit

Burner won’t light

Blockage in orifice or pilot tube

Air in gas line

Low gas pressure with tank valve fully open

Igniter fails

Dirt built up around pilot

Connection between gas valve and pilot assembly is loose

Thermocouple is not operating correctly

Gas pressure is low

Blockage in orifice

Clean or replace orifice or pilot tube, visit www.bluerhino.com for instructions.

Open gas line and bleed it (pressing control knob in) for not more than 1 - 2 minutes or until you smell gas

Turn tank valve “OFF” and replace tank

Use match to light pilot; obtain new igniter and replace

Clean dirt from around pilot

Tighten connection and perform leak check

Replace thermocouple

Turn tank valve “OFF” and replace tank

Clear blockage

Burner flame is low

Control knob is not in “ON” position

Gas pressure is low

Turn control knob to “ON”

Turn tank valve “OFF” and replace tan

Use a full tank

Emitter glows uneven

Note: Bottom 1” of emitter normally does NOT glow.

Carbon build-up

Thick black smoke

Outdoor temperature is less than 40ºF and tank is less than 1/4 full

Supply hose is bent or kinked

Control knob fully “ON”

Gas pressure is low

Base is not on a level surface

Heater is level

Dirt or film on reflector and emitter

Straighten hose

Check burner and orifices for blockage

Turn tank valvue “OFF” and replace tank

Place heater on a level surface

Clean burner

Clean reflector and emitter

Blockage in burner Remove blockage and clean burner inside and outside

For more assistance please visit us online at www.bluerhino.com or call 1.800.762.1142 for immediate assistance.

Specifications

Certifications:

CSA International Requirement 5.90

Canadian National Standard CAN1-2.23-M82

Rating:

Maximum 40,000 BTU/hr. input

Heat Range:

Up to 20 foot diameter

Fuel:

Liquid Propane Gas (LP)

Tank Size:

Nominal 20 lb / 5 Gallon

Inlet gas supply pressure:

Maximum – 150 PSI

Minimum – 5 PSI

Manifold Pressure:

11.00 in. W.C.

Engine:

IPP E8

Safety Features:

100% Burner shut-off

Tilt Switch

Manufacturer:

Blue Rhino Global Sourcing, Inc

Made In:

China

Optional Accessories

Wheel Kit

For easier portability.

Patio Heater Cover

Helps protect your heater from insects and the elements.

Please call your local supplier for more information.