Philips TAT1209 Headphones User Manual

Headphones
1000 Series
TAT1209
User manual
Register your product and get support at
www.philips.com/support
Contents
1 Important safety instructions
2
2 Your True wireless earpieces
4
Hearing safety
General information
What's in the box
Other devices
Overview of your True wireless
earpieces
2
2
4
4
5
3 Get started
6
4 Use your earpieces
9
5 Reset the earpieces
11
6 Technical data
11
7 Notice
12
Charge the battery
6
How to wear
7
Pair for the �rst time
7
Pair with another Bluetooth device 8
Connect to your Bluetooth device 9
Power on/off
9
Manage your calls and music
9
Voice Assistant
10
Earpieces LED indicator status
10
Charging box LED indicator status 10
Declaration of conformity
Disposal of your old product
and battery
Remove the integrated battery
Compliance with EMF
Environmental information
Notice of compliance
12
12
12
13
13
13
8 Trademarks
15
9 Frequently asked questions
16
1 Important
safety
instructions
Hearing safety
Danger
 To avoid hearing damage, limit the time you
use headphones at high volume and set the
volume to a safe level. The louder the volume,
the shorter the safe listening time is.
Be sure to observe the following
guidelines when using your headphones.
• Listen at reasonable volumes for
reasonable periods of time.
• Be careful not to adjust the volume
continuously upwards as your
hearing adapts.
• Do not turn up the volume so high
that you can't hear what's around
you.
• You should use caution or
temporarily discontinue use in
potentially hazardous situations.
• Excessive sound pressure from
earpieces and headphones can
cause hearing loss.
• Using headphones with both ears
covered while driving is not
recommended and may be illegal in
some areas.
• For your safety, avoid distractions
from music or phone calls while in
traffic or other potentially dangerous
environments.
2
EN
General information
To avoid damage or malfunction:
Caution
 Do not expose headphones to excessive heat.
 Do not drop your headphones.
 Headphones shall not be exposed to dripping
or splashing. (Refer to the IP rating of speci�c
product)
 Do not allow your headphones to be
submerged in water.
 Do not charge your headphones when the
connector or socket is wet.
 Do not use any cleaning agents containing
alcohol, ammonia, benzene, or abrasives.
 Use a clean, damp cloth to clean your
headphones - especially the sound conduits and
the microphone holes - regularly and avoid
buildup of substances such as sweat or earwax.
 If any sweat or water droplets are left in the
sound conduits, air holes or microphone holes,
the sound level will temporarily drop or cut out
entirely. This is not a malfunction. Use a soft,
damp cloth to dry the headphones thoroughly.
Alternatively, remove the earbud tips, turn the
sound conduits downward and gently tap the
headphones about �ve times on a dry cloth or
similar to remove any water collected inside.
 Be sure the headphones are completely dry
before charging and using. Avoid using
disposable alcohol pads or other substances for
cleaning.
 The integrated battery shall not be exposed to
excessive heat such as sunshine, �re or the like.
 Danger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type.
 To achieve the speci�c IP rating, the charging
slot cover must be closed.
 Disposal of a battery into �re or a hot oven, or
mechanically crushing or cutting a battery, can
result in an explosion.
 Leaving a battery in an extremely high
temperature surrounding environment can
result in an explosion or the leakage of
�ammable liquid or gas.
 A battery subjected to extremely low air
pressure may result in an explosion or the
leakage of �ammable liquid or gas.
 Replacement of a battery with an incorrect type
risks severely damaging the headphones and
the battery (for example, in the case of some
lithium battery types).
 If the headset is not used for a long time, the
rechargeable battery will begin to lose its
charge. To avoid this loss, please fully charge
the battery at least once every three months.
 To avoid risk of �re, the equipment is supplied
only by external power source which output
shall comply with PS1 (with output capacity less
than 15W).
Operating and storage temperatures and
humidity
• Store in a place where the
temperature is between -20°C (-4°F)
and 50°C (122 °F) with up to 90%
relative humidity.
• Operate in a place where the
temperature is between 0°C (32°F)
and 45°C (113 °F) with up to 90%
relative humidity.
• Battery life may be shorter in high or
low temperature conditions.
3
EN
2 Your True
wireless
earpieces
Congratulations on your purchase, and
welcome to Philips! To fully bene�t from
the support that Philips offers, register
your product at www.philips.com/support.
With these Philips True wireless earpieces
you can:
• Enjoy convenient wireless
handsfree calls
• Enjoy and control music wirelessly
• Switch between calls and music
Quick start guide
Warranty
Safety lea�et
What's in the box
Other devices
A mobile phone or device (e.g. notebook,
tablet, Bluetooth adapters, MP3 players
etc) which supports Bluetooth and is
compatible with the earpieces.
Philips True wireless earpieces
Philips TAT1209
Eartips x 3 pairs
Type-C charging cable (for charging only)
4
EN
Overview of your True
wireless earpieces
1
2
3
4
5
1 LED indicator (earpieces)
2 Multi-function touch (MFT)
3 Bluetooth pair button
4 LED indicator (battery state or
charging state)
5 USB-C charging slot
5
EN
3 Get started
Charge the battery
Note
Earpieces
Place the earpieces in the charging box.
•
•
The earpieces start charging and the
white LED light goes on
When the earpieces are fully charged,
the white light will go off
 Before you use your headphones, place them in
the charging box and charge the battery for 2
hours for optimum battery capacity and
lifetime.
 Use only the original USB-C charging cable to
avoid any damage.
 Finish your call before charging. Connecting the
earpieces to charge will power them off.
 If the headset is not used for a long time, the
rechargeable battery will begin to lose its
charge. To avoid this loss, please fully charge
the battery at least once every three months.
Charging Box
Plug one end of the USB-C cable into the
charging box and the other end into the
power source.
Tip
 The charging box serves as a portable backup
battery for charging the earpieces. When the
charging box is fully charged, it will fully
recharge the earpieces 2 times.
6
EN
Tip
 Normally, a full charge takes 2 hours (for the
earpieces or charging box) by USB cable.
How to wear
Select suitable ear tips for optimum �t
A tight, secure �t will provide the best
sound quality and noise-cancellation.
1
2
Test which ear tips provide you with
the best sound and wearing comfort.
Pair the earpieces with
your Bluetooth device for
the �rst time
1 Make sure that the earpieces are fully
charged and powered off.
2 Open the cover of the charging box,
the earpieces will be in pairing mode
and ready to connect.
3 sizes of silicone ear tips are
provided : large, medium, small.
L
M
The LEDs on both earpieces �ash
white and blue alternately
The earpieces are now in pairing
mode and are ready to pair with a
Bluetooth device
(e.g. a mobile phone)
S
3 Turn on the Bluetooth function of
your Bluetooth device.
4 Pair the earpieces with your
Bluetooth device, refer to the user
manual of your Bluetooth device.
Insert the earpieces
1 Check left or right orientation of the
earpieces.
2 Insert the earpieces into the ears
and twist slightly until a secure �t is
achieved.
Note
 After powering on, if the earpieces can not �nd
any previously connected Bluetooth device,
please put them into pairing mode (press button
on box for 3 seconds with both earpieces inside
and the cover open).
The following example shows you
how to pair the earpieces with your
Bluetooth device.
1
Turn on the Bluetooth function of
your Bluetooth device, select
Philips TAT1209.
7
EN
2
Enter the earpieces' password “0000”
(4 zeros) if prompted. For those
devices featuring Bluetooth 3.0 or
higher, there is no need to enter a
password.
Philips TAT1209
Pair the earpieces with
another Bluetooth device
If you want to pair another Bluetooth
device with the earpieces, just put them
into pairing mode, (press button on box for
3 seconds with both earpieces inside and
the cover open), then discover the second
device as per normal pairing.
Single earpiece (Mono mode)
03"
Take either right or left earpiece out
from charging box for Mono use. The
earpiece will power on automatically.
Note
 Take the second earpiece from the charging box
and they will pair with each other automatically.
8
EN
Note
 The earpieces store 4 devices in the memory.
If you try to pair more than 4 devices, the earliest
paired device is replaced by the new one.
4 Use your
earpieces
Connect the earpieces to
your Bluetooth device
1 Turn on the Bluetooth function of
Power on/off
Task
MFT
Operation
Turn the
earpieces on
Open the
charging box
to power on
Turn the
earpieces off
Close the
charging box
to power off
your Bluetooth device.
2 Open the charging box cover.
The blue LED �ashes.
The earpieces will search the last
connected Bluetooth device and
reconnect to it automatically. If
the last connected one is not
available, the earpieces will search
and reconnect to the second last
connected device.
Tip
 If you turn on the Bluetooth function of your
Bluetooth device after turning on the earpieces,
you have to go to the Bluetooth menu of the
device and connect the earpieces to the device
manually.
Note
 In some Bluetooth devices, connection may not
be automatic. In this case, you have to go to the
Bluetooth menu of your device and connect the
earpieces to the Bluetooth device manually.
Manage your calls and
music
Music control
Task
MFT
Operation
Play or pause
music
Next track
Right
earpiece
Right
earpiece
Double tap
Previous track Left
earpiece
Triple tap
Adjust
volume +
Right
earpiece
Adjust
volume -
Left
earpiece
Tap once
then long
touch
Tap once
then long
touch
Tap and
hold
Dynamic bass Left
on/off
earpiece
Triple tap
9
EN
Call control
Operation
Task
MFT
Pick up/
Hang up call
Right/Left Single tap
earpiece
Hang up call/
Reject call
Right/Left Double tap
earpiece
Voice Assistant
Task
MFT
Operation
Trigger Voice
(Siri/Google)
Assistant
Right
earpiece
Continue
touching
after beep
Stop Voice
Assistant
Right
earpiece
Single tap
Gaming mode
(low latency mode)
Task
MFT
Operation
Gaming mode
on/off
Left
earpiece
Double tap
10
EN
Earpieces LED indicator
status
Earpieces status
Indicator
The earpieces are
connected to a
Bluetooth device
The earpieces are
ready for pairing
White LED blinks
once
The earpieces are
on but not
connected to a
Bluetooth device
Low battery level
(earpieces)
Battery is fully
charged
(charging box)
The LED �ashes
blue and white
alternately
White LED blinks
every second
(auto turn off after
3 minutes)
White LED blinks 3x
every 5 seconds
Refer to case LED
Charging box LED indicator
status
When charging
Indicator
Battery low
Amber LED lights
up
Relative adequate
battery
White LED lights
up
In use and cover
is open
Indicator
Battery low
White LED slowly
blinks for 4 cycles
Relatively
adequate battery
Off
5 Reset the
earpieces
If you encounter any pairing or connection
issue, you can follow the following
procedure to reset your earpieces to
factory default settings.
1
On your Bluetooth device, go to the
Bluetooth menu and remove Philips
TAT1209 from the device list.
2
Turn off the Bluetooth function of
your Bluetooth device.
3
Return earpieces to charging box
and open the lid.
4
Press button on box twice.
5
Follow steps in “Use your earpiecesconnect the earpieces to your
Bluetooth device.”
6
Pair the earpieces with your
Bluetooth device, select Philips
TAT1209.
If there is no response from the
earpieces, you can follow the below step
to reset the hardware of your earpieces.
Return earpieces to charging box and
open the lid, press the button on box
for more than 10 seconds.
6 Technical data
Music play time : 6 + 12 hours
Standby time: 200 hours
Charging time: 2 hours
Lithium-ion battery 40 mAh on
each earpiece, Lithium-ion battery
300 mAh on charging box
Bluetooth version: 5.3
Compatible Bluetooth pro�les:
•
HFP (Hands-Free Pro�le)
•
A2DP (Advanced Audio
Distribution Pro�le)
•
AVRCP (Audio Video Remote
Control Pro�le)
Supported audio codecs: SBC
Frequency range: 2.402-2.480 GHz
Transmitter power: < 10 dBm
Operating range: Up to 10 meters
(33 feet)
USB-C port for charging
Low battery warning: available
Note
 Speci�cations are subject to change without
notice.
11
EN
7 Notice
Declaration of conformity
Hereby, TP Vision Europe B.V. declares that
the product is in compliance with the
essential requirements and other relevant
provisions of RED Directive 2014/53/EU and
UK Radio Equipment Regulations SI 2017
No 1206. You can �nd the Declaration of
Conformity on www.philips.com/support.
Remove the integrated
battery
If there is no collection/recycling system
for electronic products in your country,
you can protect the environment by
removing and recycling the battery before
disposing of the earpieces.
•
Make sure the earpieces are
disconnected from the charging box
before removing the battery.
•
Make sure the charging box is
disconnected from the USB charging
cable before removing the battery.
Disposal of your old
product and battery
Your product is designed and manufactured
with high quality materials and components
which can be recycled and reused.
This symbol on a product means that the
product is covered by European Directive
2012/19/EU.
This symbol means that the product
contains a built-in rechargeable battery
covered by European Directive 2013/56/EU
which cannot be disposed of with normal
household waste. We strongly advise you to
take your product to an official collection
point or a Philips service centre to have a
professional remove the rechargeable
battery. Inform yourself about the local
separate collection system for electrical and
electronic products and rechargeable
batteries. Follow local rules and never
dispose of the product and rechargeable
batteries with normal household waste.
Correct disposal of old products and
rechargeable batteries helps prevent
negative consequences for the environment
and human health.
12
EN
Environmental information
All unnecessary packaging has been
omitted. We have tried to make the
packaging easy to separate into three
materials: cardboard (box), polystyrene
foam (buffer) and polyethylene (bags,
protective foam sheet.)
Your system consists of materials which
can be recycled and reused if
disassembled by a specialized company.
Please observe the local regulations
regarding the disposal of packaging
materials, exhausted batteries and old
equipment.
Notice of compliance
The device complies with the FCC rules,
Part 15. Operation is subject to the
following two conditions:
1. This device may not cause harmful
interference, and
2. This device must accept any
interference received, including
interference that may cause
undesired operation.
FCC rules
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to part 15
of the FCC Rules. These limits are
designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses and can
radiate radio frequency energy and, if
not installed and used in accordance with
the instruction manual, may cause
harmful interference to radio
communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or
television reception, which can be
determined by turning the equipment
off and on, the user is encouraged to try
to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between
equipment and receiver
Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC
radiation exposure limits set forth for an
uncontrolled environment.
This transmitter must not be co-located
or operating in conjunction with any
other antenna or transmitter.
Caution: The user is cautioned that
changes or modi�cations not expressly
approved by the party responsible for
compliance could void the user's
authority to operate the equipment.
Canada:
This device contains licence-exempt
transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence- exempt
RSS(s). Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference, and
(2) This device must accept any
interference received, including
interference that may cause undesired
operation of the device.
CAN ICES-003(B)/NMB-003(B)
IC Radiation Exposure Statement:
This equipment complies with Canada
radiation exposure limits set forth for
uncontrolled environments.
This transmitter must not be co-located
or operating in conjunction with any
other antenna or transmitter.
13
EN
Avis de conformité
Cet appareil satisfait aux règlements de
la FCC partie 15 du Code of Federal
Regulations. Son fonctionnement est
assujetti aux deux conditions suivantes :
1. Cet appareil ne doit pas causer
d’interférence préjudiciable et
2. l’appareil doit accepter toute
interférence reçue, y compris les
interférences qui peuvent causer un
fonctionnement non désiré.
Règlement de la FCC
Cet équipement a été testé et jugé
compatible avec les limites s’appliquant
aux appareils numériques de la classe B,
conformément à l’article 15 du
règlement de la FCC. Ces limites ont été
dé�nies pour fournir une protection
raisonnable contre les interférences
nuisibles dans le cadre d’une installation
résidentielle. Cet équipement génère,
utilise et peut émettre de l’énergie
radiofréquence et, s’il n’est pas installé ni
utilisé conformément aux instructions,
peut causer des interférences gênantes
pour les communications radio.
Rien ne garantit toutefois que des
interférences ne surviendront pas dans
une installation particulière. Si cet
équipement cause des interférences
nuisibles pour la réception de la radio ou
de la télévision, ce qui peut être
déterminé en mettant l’équipement hors
tension puis sous tension, l’utilisateur
devra essayer de corriger ces
interférences en effectuant une ou
plusieurs des opérations suivantes :
• Déplacez l’antenne de réception.
• Augmentez la distance entre
l’équipement et le récepteur.
• Branchez l’équipement à une prise
d’un circuit autre que celui sur lequel
le récepteur est branché.
14
EN
• Consultez le détaillant ou un
technicien de radiotélévision
expérimenté.
Canada :
Le présent appareil est conforme aux
CNR d’Industrie Canada applicables aux
appareils radio exempts de licence.
L’exploitation est autorisée aux deux
conditions suivantes : (1) l’appareil ne
doit pas produire de brouillage, et (2)
l’utilisateur de l’appareil doit accepter
tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en
compromettre le fonctionnement.
CAN ICES-003(B)/NMB-003(B)
Déclaration d’IC sur l’exposition aux
radiations:
Cet équipement est conforme aux limites
d’exposition aux radiations dé�nies par le
Canada pour des environnements non
contrôlés.
Cet émetteur ne doit pas être installé au
même endroit ni utilisé avec une autre
antenne ou un autre émetteur.
8 Trademarks
Bluetooth
The Bluetooth® word mark and logos are
registered trademarks owned by
Bluetooth SIG, Inc. and any use of such
marks by MMD Hong Kong Holding
Limited is under license. Other
trademarks and trade names are those of
their respective owners.
Siri
Siri is a trademark of Apple Inc., registered
in the U.S. and other countries.
Google
Google and Google Play are trademarks of
Google LLC.
15
EN
9 Frequently
asked
questions
My Bluetooth earpieces do not turn on.
The battery level is low. Charge the
earpieces.
I cannot pair my Bluetooth earpieces
with my Bluetooth device.
The Bluetooth is disabled. Enable the
Bluetooth feature on your Bluetooth
device and turn on the Bluetooth device
before you turn on the earpieces.
Pairing does not work.
• Put both earpieces into charging box.
• Make sure you have disabled the
Bluetooth function of any previously
connected Bluetooth devices.
• On your Bluetooth device, delete
“Philips TAT1209” from the Bluetooth
list.
• Pair your earpieces (see ‘Pair the
earpieces with your Bluetooth device
for the �rst time’ on page 7).
The Bluetooth device cannot �nd the
earpieces.
• The earpieces may be connected to a
previously paired device. Turn off the
connected device or move it out of
range.
• Pairing may have been reset or the
earpieces have been previously paired
with another device. Pair the
earpieces with the Bluetooth device
again as described in the user manual.
(see ‘Pair the earpieces with your
Bluetooth device for the �rst time’ on
page 7).
16
EN
My Bluetooth earpieces are connected to
a Bluetooth stereo-enabled mobile
phone, but music only plays on the
mobile phone speaker.
Refer to the user manual of your mobile
phone. Select to listen to music through
the earpieces.
The audio quality is poor and a crackling
noise can be heard.
• The Bluetooth device is out of range.
Reduce the distance between your
earpieces and Bluetooth device, or
remove obstacles between them.
• Charge your earpieces.
The audio quality is poor when
streaming from a mobile phone is very
slow or streaming does not work at all.
Make sure your mobile phone not only
supports (mono) HFP but also supports
A2DP and is BT4.0x (or higher)
compatible (see ‘Technical data’ on page
11).
Clean your headphones regularly.
• Use a clean, damp cloth to clean your
headphones - especially the sound
conduits and the microphone holes regularly and avoid buildup of
substances such as sweat or earwax.
• If any sweat or water droplets are left
in the sound conduits, air holes or
microphone holes, the sound level
will temporarily drop or cut out
entirely. This is not a malfunction. Use
a soft, damp cloth to dry the
headphones thoroughly.
Alternatively, remove the earbud tips,
turn the sound conduits downward
and gently tap the headphones about
5 times on a dry cloth or similar to
remove any water collected inside.
• Be sure the headphones are
completely dry before charging and
using. Avoid using disposable alcohol
pads or other substances for cleaning.
Charge your headphones regularly.
If the headphones are not used for a
long time, the rechargeable battery will
begin to lose its charge. To avoid this loss,
please fully charge the battery at least
once every three months.
17
EN
2023 © MMD Hong Kong Holding Limited. All rights reserved.
Speci�cations are subject to change without notice. Philips and
the Philips Shield Emblem are registered trademarks of
Koninklijke Philips N.V. and are used under license. This product
has been manufactured by and is sold under the responsibility of
MMD Hong Kong Holding Limited or one of its affiliates, and
MMD Hong Kong Holding Limited is the warrantor in relation to
this product. All other company and product names may be
trademarks of its respective companies with which they are
associated.
UM_TAT1209_00_EN_V1.0
">