Kogan KABTHDJBLKA Wireless Headphones Midnight Black User Manual

KABTHDJBLKA
USER MANUAL
https://manual-hub.com/
User Manual
What's in the Box.
1. Headphones
2. Micro USB Cable
3. 3.5mm audio cable
Please read carefully this manual before using headphones, and keep a copy handy for
future reference.
https://manual-hub.com/
Know your headphones:
1. Toggle switch - Three Direction – Three Functions
a. Move Upwards: Volume + / Previous track
b. Move Downwards: Volume - / Next track
c. Press it In: Pause / Play
2. Power button / Bluetooth power button
3. Micro USB slot
4. Line in slot
5. Mic
■Specification and Parameter:
Dimension ：200x170x75(mm)
Weight ：175g（bare headphone, without packaging）
Charging interface： Micro USB
Press buttons： two （power button + toggle switch ）
Battery ： 3.7V/250mAh
Charging specification：Micro USB
Charging input ： 5V/1.0A
Charging indication ：
Solid Red LED light
Standby time ： about 100 hours
Successive talking time： about 8 hours
Charging time: 2-3 hours
Volume control：16 ranks, 3dB variation in each rank
Working temperature ： -20～70℃ during the charging period
Storage temperature： -40～80℃
https://manual-hub.com/
■Speaker parameter
Speaker diameter: Φ40mm
Impedance： Impedance: 32Ω
Sensitivity：S.P.L:110dB S.P.L.at 1KHz
Rated power: 20mW
Frequency Response: 100Hz-9000Hz
■Microphone parameter
Microphone Unit: Φ4*1.5mm
Directivity: Omni direction
S.P.L: -42±3dB
Impedance: ≤2.2KΩ
Frequency Response: 20-20,000HZ
Operating voltage: 4.2V
■Bluetooth Mode:
Device Mode Number： BT513
Bluetooth Protocol version： CSR , Version 2.1+EDR
Remote control to the player：
Volume up and down, Previous /Next, Pause/Play
Receiver range: 10m / 360°
Pairing code: 0000
SNR： -82dBm
Carrier frequency: 2402MHz - 2480MHz
Frequency response: 20Hz – 20,000Hz
Successive working time: Approximately 8 hours
Standby time: Approximately 100 hours
https://manual-hub.com/
■Operation
Turn ON： In the state of power-off, press and hold the power button for 1sec, the headset will
send out two “di-di” Prompt tones and blue LED will be on ; the blue and red LED light will
glitters in turn if holding power button for 4 sec.
Turn OFF ： In the state of power-on, press and hold power button for 3 seconds till the blue
LED light glitters three times. There will be four "dodo” voices from loud to low. Now the unit
is turned off.
Pairing： In the state of power-off , press and hold power button for 3s until red and blue LED
light glitters in turn, the headphone enters into pairing mode. In this case, the headset can be
paired with the Bluetooth enabled device.
※ Usually ， Setup procedure relates to the “setup”,” connection” or “Bluetooth” menu in your
mobile phone or Bluetooth device. Click “search for Bluetooth device”, your phone will find the
headphone name ”513” or similar pairing name and ask if you want to connect, then click
“confirm” or “yes”. Afterwards, input the pairing password or PIN code ”0000” and click ”yes” or
“confirm”, the headphone will connect with your Bluetooth device successfully.
※ The headphone will enter in power-on mode if releasing power button before red and blue
LED light glitters in turn. In this case, please turn off the power and operate it once again.
Answering calls: Press the power button once to answer the incoming calls.
Dialing calls: If the headset is paired with the mobile phone, dialing the numbers on the cell
phone will enable the conversation on the headset automatically .
Ending calls: Ongoing conversation on cell phone can be ended by pressing the power key
once.
Redial latest number: The cell phone will automatically dial the last dialed phone number
by double pressing power key on the Bluetooth headset. We can hear the prompt tone from
the headset.
Volume control: In the state of music or calls, move toggle switch upwards to increase the
sound and move it downwards to decrease the sound.
Previous /Next: Move the toggle switch upwards and hold it for a short while to come to
previous song, then move the toggle switch downwards and hold it for a short while to come to
next song.
Pause /Play: Press the toggle switch button inside to pause or play the music.
https://manual-hub.com/
■Wired headphone Function
The headphone can be used as the wired headphone. Just simply attach 3.5mm audio
cable.
In the state of power off: It can be used as the wired stereo headphone by inserting the
3.5mm audio cable. Please adjust the volume of sound sources when it is as the wired
headphone. In this case, the volume control of the headphone can' t be workable.
■Symbol of LED Light ：
Power on---Blue light is on.
Power off---No light.
Charging---Red light is on. No light is on when is fully charged.
Power Shortage---Red light flashes.
Pairing mode---Red and blue lights flash in turn
https://manual-hub.com/