PXIe-6396
DAQ GETTING STARTED GUIDE
PXI/PXI Express
This document provides basic installation instructions for National Instruments PXI and
PXI Express DAQ modules. Refer to the documentation specific to your DAQ module for
more information.
Unpacking the Kit
Caution To prevent electrostatic discharge (ESD) from damaging the device,
1.
2.
ground yourself using a grounding strap or by holding a grounded object, such as
your computer chassis.
Touch the antistatic package to a metal part of the computer chassis.
Remove the device from the package and inspect the device for loose components or any
other sign of damage.
Caution Never touch the exposed pins of connectors.
Note Do not install a device if it appears damaged in any way.
3.
Unpack any other items and documentation from the kit.
Store the device in the antistatic package when the device is not in use.
Installing the Software
Back up any applications before upgrading your software. You must be an Administrator to
install NI software on your computer. Refer to the NI-DAQmx Readme on the software media
for supported application software and versions.
1. If applicable, install an application development environment (ADE), such as LabVIEW,
Microsoft Visual Studio®, or LabWindows™/CVI™.
2.
Install the NI-DAQmx driver software.
Installing the Module
1.
(Optional) If you are using a MXI-Express connected chassis, turn off your computer.
Note For more information about using MXI-Express chassis, refer to your
chassis manual.
2.
Power off and unplug the PXI/PXI Express chassis. Refer to your chassis manual to
install or configure the chassis.
Caution Refer to the Read Me First: Safety and Electromagnetic
Compatibility with your PXI/PXI Express chassis or device before removing
covers or connecting or disconnecting signal wires.
Figure 1. Installing a PXI/PXI Express Module in the Chassis
1
PX
I-1
2
000
B
7
3
6
5
4
1. PXI/PXI Express Chassis
2. PXI/PXI Express Chassis or MXI-Express
Controller
3. PXI/PXI Express Module
4. Injector/Ejector Handle
3.
5. Front-Panel Mounting Screws
6. Module Guides
7. Power Switch
Identify a supported PXI/PXI Express slot in the chassis.
Some modules have PXI/PXI Express slot requirements; for information, refer to the
module documentation.
Figure 2. Symbols for PXI Express/PXI Express Hybrid/PXI Slots
NI PXIe-1062Q
1
1. PXI Express System Controller Slot
2. PXI Peripheral Slot
2
3
4
3. PXI Express Hybrid Peripheral Slot
4. PXI Express System Timing Slot
If you are using a PXI Express chassis, you can place PXI modules in the PXI slots. If a
PXI module is hybrid slot compatible, you can use the PXI Express Hybrid slots.
PXI Express modules can be placed only in PXI Express slots and PXI Express Hybrid
slots. Refer to the chassis documentation for details.
4.
Remove the filler panel of an unused PXI/PXI Express slot.
2 |
ni.com |
DAQ Getting Started Guide for PXI/PXI Express
5.
Touch any metal part of the chassis to discharge static electricity.
6.
Ensure that the PXI/PXI Express module injector/ejector handle is not latched and swings
freely.
7.
Place the PXI/PXI Express module edges into the module guides at the top and bottom of
the chassis.
8.
Slide the module into the PXI/PXI Express slot to the rear of the chassis.
9.
When you begin to feel resistance, pull up on the injector/ejector handle to latch the
device.
10. Secure the module front panel to the chassis using the front-panel mounting screws.
11. Plug in and power on your PXI/PXI Express chassis.
12. (Optional) If you are using a MXI-Express connected chassis, turn on your computer.
13. If applicable, install accessories and/or terminal blocks as described in the installation
guides.
14. Attach sensors and signal lines to the device, terminal block, or accessory terminals.
Refer to the documentation for your DAQ device or accessory for terminal/pinout
information.
Configuring the Device in NI MAX
Use NI MAX, installed automatically with NI-DAQmx, to configure your National
Instruments hardware.
1. Launch NI MAX.
2.
In the Configuration pane, double-click Devices and Interfaces to see the list of installed
devices. The module is nested under the chassis.
If you do not see your device listed, press <F5> to refresh the list of installed devices.
3.
Right‑click the device and select Self-Test to perform a basic verification of hardware
resources.
4.
(Optional) Right‑click the device and select Configure to add accessory information and
configure the device.
5.
Right-click the device and select Test Panels to test device functionality.
Click Start to test the device functions, and then Stop and Close to exit the test panel. If
the test panel displays an error message, refer to ni.com/support.
6.
If your device supports Self-Calibration, right-click the device and select Self-Calibrate.
A window reports the status of the calibration. Click Finish. For more information about
Self-Calibration, refer to the device user manual.
Note Remove all sensors and accessories from your device before SelfCalibrating.
DAQ Getting Started Guide for PXI/PXI Express
|
© National Instruments |
3
Programming
Complete the following steps to configure a measurement using the DAQ Assistant from
NI MAX.
1. In NI MAX, right-click Data Neighborhood and select Create New to open the DAQ
Assistant.
2.
Select NI-DAQmx Task and click Next.
3.
Select Acquire Signals or Generate Signals.
4.
Select the I/O type, such as analog input, and the measurement type, such as voltage.
5.
Select the physical channel(s) to use and click Next.
6.
Name the task and click Finish.
7.
Configure individual channel settings. Each physical channel you assign to a task
receives a virtual channel name. Click Details for physical channel information.
Configure the timing and triggering for your task.
8.
Click Run.
Troubleshooting
For software installation problems, go to ni.com/support/daqmx.
For hardware troubleshooting, go to ni.com/support and enter your device name, or go to
ni.com/kb.
Find device terminal/pinout locations in MAX by right-clicking the device name in the
Configuration pane and selecting Device Pinouts.
To return your National Instruments hardware for repair or device calibration, go to ni.com/
info and enter rdsenn, which starts the Return Merchandise Authorization (RMA) process.
Where to Go Next
Additional resources are online at ni.com/gettingstarted and in the NI-DAQmx Help. To access
NI-DAQmx Help, launch NI MAX and go to Help»Help Topics»NI-DAQmx»NI-DAQmx
Help.
Examples
NI-DAQmx includes example programs to help you get started developing an application.
Modify example code and save it in an application, or use examples to develop a new
application or add example code to an existing application.
To locate LabVIEW, LabWindows/CVI, Measurement Studio, Visual Basic, and ANSI C
examples, go to ni.com/info and enter the Info Code daqmxexp. For additional examples,
refer to ni.com/examples.
4 |
ni.com |
DAQ Getting Started Guide for PXI/PXI Express
Related Documentation
To find the documentation for your DAQ device or accessory—including safety,
environmental, and regulatory information documents—go to ni.com/manuals and enter the
model number.
Worldwide Support and Services
The NI website is your complete resource for technical support. At ni.com/support, you have
access to everything from troubleshooting and application development self-help resources to
email and phone assistance from NI Application Engineers.
Visit ni.com/services for NI Factory Installation Services, repairs, extended warranty, and
other services.
Visit ni.com/register to register your NI product. Product registration facilitates technical
support and ensures that you receive important information updates from NI.
NI corporate headquarters is located at 11500 North Mopac Expressway, Austin, Texas,
78759-3504. NI also has offices located around the world. For telephone support in the United
States, create your service request at ni.com/support or dial 1 866 ASK MYNI (275 6964). For
telephone support outside the United States, visit the Worldwide Offices section of ni.com/
niglobal to access the branch office websites, which provide up-to-date contact information,
support phone numbers, email addresses, and current events.
DAQ Getting Started Guide for PXI/PXI Express
|
© National Instruments |
5
Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for information on NI trademarks. Other product and
company names mentioned herein are trademarks or trade names of their respective companies. For patents covering NI
products/technology, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your media, or the
National Instruments Patent Notice at ni.com/patents. You can find information about end-user license agreements (EULAs)
and third-party legal notices in the readme file for your NI product. Refer to the Export Compliance Information at ni.com/
legal/export-compliance for the NI global trade compliance policy and how to obtain relevant HTS codes, ECCNs, and other
import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES AS TO THE ACCURACY OF THE INFORMATION
CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. U.S. Government Customers: The data contained in
this manual was developed at private expense and is subject to the applicable limited rights and restricted data rights as set forth
in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015.
© 2016 National Instruments. All rights reserved.
376575A-01
Aug16
">
