BURG secuENTRY Set ENTRY 7601 PIN Pincode-Set Instruction manual

Contents index
English
Initial setup
secuENTRY easy
ENTRY 7601 PIN
2
Further languages at:
www.burg.biz
Foreword
Dear Customer,
Thank you very much for deciding on the secuENTRY Set
ENTRY 7601 PIN, consisting of the ENTRY 7600 CYL cylinder and
the ENTRY 7711 Keypad PIN.
The system was developed in Germany according to the most
modern technical capabilities and fulfils the latest high safety
requirements.
Setup with app
BURGsmart
The ENTRY 7600 CYL electronic cylinder can be easily installed
in any door with a mortise lock, up to a door thickness of
118 mm (59/59 mm, measured in the centre of the forend
screw). No drilling or laying of cables is required and it is
ideally suited for both new installations and retrofitting. The
ENTRY 7600 CYL can be fitted to house and interior doors.
Using the ENTRY 7711 Keypad PIN, you can unlock and lock the
door with a 6-digit user code. The ENTRY 7711 Keypad PIN can
be installed up to approx. four metres from the locking unit,
depending on preference and conditions.
The ENTRY 7600 CYL is setup and operated using the free
smartphone app BURGsmart*. The transmission is wireless, the
cylinder uses the modern Bluetooth 5.2 standard.
*
Video instructions
Simple instructions on the
setup and operation of your
secuENTRY components.
Follow the QR code or go to...
BURG-WÄCHTER KG
Altenhofer Weg 15
58300 Wetter
Germany
Alternatively, the cylinder can also be operated by keypad (e.g. ENTRY 7712
Keypad FP), the radio key ENTRY sE-Key 7713, as well as other add-on products
(all items available separately. For a complete list of all compatible products,
please refer to page 13 of these instructions). The BURGsmart app is however
always required for the setup.
https://t1p.de/burgsmart-app
www.burg.biz
! Important:
Please read the entire operating instructions
before you start the installation.
We hope you enjoy your new locking system!
Set contents
Technical data - ENTRY 7600 CYL Cylinder
II
I
I
ENTRY easy 7600 CYL Cylinder
II ENTRY 7711 Keypad PIN
III Adapter 1 incl. 2x M2x10 screws
V
IV Adapter 2 incl. 1x 2.9x13 screw
IV
III
V Emergency lock cover (2x)
VI Emergency key
VII Forend screw
XI
VI
VIII Adhesive pads (4x)
XIV
VII
Cylinder unit power supply
2x Mignon LR6 AA Alkaline
Permitted ambient conditions
-15 °C/+50 °C / up to 95 %
relative humidity (non-condensing)
Radio standard
Bluetooth 5.2 LE
Transmission power
≤ 10 dBm
Frequency range
2.4 - 2.483 GHz
Range
Approx. 4 m
Number of access media
Up to 2,000 user codes (incl. one administrator
code)*, sE keys** or BURGsmart connections,
of which max. 45 fingerprints*** when using
a fingerprint keypad or 300 when using the
PC software****.
Blocking times
After 3x incorrect entries of an opening media
1 minute, thereafter 3 minutes each time
IX Dowels (3x)
XII
X Screws (3x)
VIII
IX
XI Hexagon spanner SW2
XIII
XII Screwdriver TX8
XIII QR-Code sticker
X
XIV Quick Start Guide plus warranty
and disposal instructions
Fig. 1
! Note:
The integrated manipulation protection in the cylinder ensures that the cylinder is blocked for
one minute after three incorrect entries of an opening media. From the fourth incorrect entry,
the cylinder is blocked for three minutes each time.
QR code/Administrator code
The QR codes (I) are required later when setting
up the set using the BURG-WÄCHTER BURGsmart
app (Fig. 1).
The sets are delivered from the factory with a random administrator code (II) (Fig. 1), consequently
a code change is not mandatory.
! Attention:
Neither the QR codes nor the factory-gen-
erated administrator code are stored by
BURG-WÄCHTER. Recovery is not possible
if the codes are lost. It is important to keep
the QR code stickers enclosed with the set
in a safe place. We further recommend that
you photograph the stickers and also archive
them digitally.
2 I English
Technical data - ENTRY 7711 Keypad PIN
I
Keypad power supply
Permitted ambient conditions
I
QR
QR
Radio standard
Transmission power
Frequency range
Range
Weather protection class (IP class)
II
2x Mignon LR6 AA Alkaline
-15 °C/+50 °C / up to 95 %
relative humidity (non-condensing)
Bluetooth 5.2
≤ 10 dBm
2.4 - 2.483 GHz
Approx. 4 m
IP53
The user code can only be used as an opening media in conjunction with the ENTRY 7711 keypad PIN, ENTRY 7712 keypad FP or
ENTRY 7722 keypad FP (available as an option. ENTRY 7711 PIN included in the set).
Radio key ENTRY sE-Key 7713 available as an option.
***
The fingerprint can only be used as an opening media in conjunction with the fingerprint keypad ENTRY 7712 Keypad FP or
ENTRY 7722 Keypad FP (available as an option).
****
Additional input of fingerprints is possible using Windows software ENTRY 7783 Pro and the programming device ENTRY 7073 Enrolment
(both available as an option).
*
**
Cylinder QR code sticker
Keypad QR code sticker
Fig. 1
secuENTRY easy | ENTRY 7601 PIN
Set the keypad to programming mode
ENTRY 7711 Keypad PIN
The ENTRY 7711 Keypad PIN can be used to operate electronic secuENTRY cylinders from
BURG-WÄCHTER. Communication between the keypad and the profile cylinder is 128-bit AES
encrypted.
Operation on the illuminated keypad is carried out via push-buttons. Consequently, the keypad
can be easily operated even in poor lighting conditions.
The ENTRY 7711 Keypad PIN enables the door to be opened and closed with the aid of a 6-digit PIN
code (= 1 million number combinations).
The keypad is splash-proof on all sides according to IP53 certification.
Please refer to this chapter if the keypad
has to be set to programming mode
in the course of the setup. Position the
smartphone and keypad within Bluetooth range of each other and carry out
the following steps.
Fig. 2
1 When you reach the view shown in
the illustration (Fig. 1), briefly lay the
smartphone aside and set the keypad
to programming mode using the
following steps.
Fig. 3
In order for the data transfer
! Attention:
between smartphone and keypad to
occur, the smartphone must be in direct
proximity to the keypad for the following step (Bluetooth range)
ON button
Entry prompt
2 Activate the keypad with the ON button
(Fig. 2).
Status LED
CLOSE button
Status LED
Fig. 4
Fig. 5
Fig. 6
The security code can be found
! Note:
on the enclosed QR code sticker (Fig. 3).
The security code (SCD) serves as
! Note:
manipulation and theft protection
Cylinder status
Fig. 1
Activates the keypad. An entry "Opened" (ON button) or "Closed"
(CLOSE button) is generated in the secuENTRY cylinder history.
This allows for the "Open" and "Close" operations to be differentiated
CLOSE button
in the history.
The two LEDs next to the X symbol will illuminate if an invalid number
Error message
combination is entered or if general errors occur.
The system monitors the keypad and cylinder battery voltage.
The user is alerted as soon as the battery voltage reaches a critical
Battery status
range. Batteries must be changed as soon as possible after the battery
status symbol illuminates.
When the number combination entered is correct, the cylinder status
Cylinder status
symbol will illuminate and the door can be unlocked or locked.
The LEDs illuminate one after the other in a clockwise direction when
Status LED
the keypad is in programming mode (see chapter below).
3 I English
Fig. 1
3 Enter the security code (SCD) provided
using the keypad.
Battery status
ON button
5 seconds
4 Press and hold the CLOSE button for
five seconds (Fig. 4) until the signal
LEDs on the keypad illuminate one
after the other in a clockwise direction
(Fig. 5).
5 The keypad is now in programming
mode. Perform the further steps using
the smartphone again (Fig. 6).
secuENTRY easy | ENTRY 7601 PIN
ENTRY easy 7601 PIN activation
I - User
1 First of all, download the BURGsmart
app in order to be able to set up your
new locking system. This can be found
in the iOS App Store and Google Play
Store (Fig. 1).
BURGsmart
Fig. 1
The Android version of the
! Note:
BURGsmart app has been used for these
4
I
User data
5
3 Enter your name and a mail address
(Fig. 3).
3 An overview of the user data appears.
If you have created a new user, first
enter the first name and surname of
the user (I) (Fig. 3).
Access data
This section allows you to enter
! Note:
the desired opening media (e.g. user
6
Fig. 2
Fig. 3
5 Read through and agree to the terms of
use and privacy policy (Fig. 3).
code or fingerprint) for the user (II)
(Fig. 3). The lock opening by smartphone is automatically stored in the
administrator's user profile.
Access data | User code
6 Tap on "Register" (Fig. 3).
!
II
To do so, tap the "+" in the top righthand corner (II) (Fig. 2).
2 You will be shown licence provisions
for the use of the app when you open
it for the first time. Carefully read them
and then confirm by clicking "OK" in the
bottom right-hand corner (Fig. 2).
4 Select them the item: "BURG-WÄCHTER
Cloud" this is not required for the setup
and can therefore be ignored for the
time being ( Fig. 3). An explanatory
note on this subject can be found in the
master operating instructions on our
website (see link on the title page).
2 A list of the users that have already
been created is displayed. A user profile
with a lock opening via smartphone has
already been automatically created for
the administrator. Tap on this (I) (Fig. 2).
Alternatively, a new additional
! Note:
user profile can be created at this point.
3
instructions. The iOS version can be
slightly different visually, but the work
steps are identical.
1 Tap on the menu item "I - User" (Fig. 1).
Fig. 1
Fig. 2
I
II
III
4 Enter a required 6 digit user code under
"Enter 6-digit code" (III) (Fig. 3).
Note: An e-mail window opens with
a mail template which you can use to
send the registration data to the specified e-mail address. This is necessary,
for example, when using the secuENTRY
Windows software. It is not required for
the setup described here. The data can
also be called up again in the app at
a later time if required.
Fig. 3
7 The BURGsmart app main screen
appears. Open the "My System" menu
at the bottom left (Fig. 4).
Fig. 4
4 I English
secuENTRY easy | ENTRY 7601 PIN
If you wish to enter opening
! Note:
media for other users, go back one
Access data | Enter RFID tag
5 An RFID transponder ENTRY 7710 RFID
(optionally available) can be entered
at this point. Instructions on how to
set this up can be found in the RFID
transponder instructions (I) (Fig. 4).
!
menu and select the respective user
(Fig. 7). Repeat the steps in this chapter
for this user.
8 You can now leave the menu (I - User).
Return to the "My System" menu (Fig. 8).
Attention: This cylinder in this set
requires the add-on article ENTRY
7174 RFID Extender for the use of RFID
transponders. For a complete list of all
compatible products, please refer to
page 14 of these instructions.
I
II
III
Access data | Enter sE-Key
6 A radio key ENTRY sE-Key 7713
(optionally available) can be stored
at this point (II) (Fig. 4). Instructions
on how this is setup can be found in
the radio key instructions.
Fig. 4
Fig. 7
Fig. 8
Access data | Smartphone as key
The lock opening by smartphone
! Note:
is automatically stored in the administrator's user profile (III) (Fig. 4). A different smartphone as the electronic key
can be stored in this field for additional
users. An instructions on this subject
can be found in the master operating
instructions on our website (see link on
the title page).
Manage fingerprint
7 If you have the optional fingerprint
keypad (e.g. ENTRY 7712 FP), you
can store then register a finger as
the opening media in this section.
Instructions on how to set this up can
be found in the instructions for the
respective item (Fig. 5).
Fig. 5
Fig. 6
The ENTRY 7711 PIN pincode
! Note:
keypad is included in this set.
5 I English
secuENTRY easy | ENTRY 7601 PIN
II - secuENTRY units
5 The capture window of the camera
opens. Scan the QR code.
1 Tap on the second menu item
"II - secuENTRY units" (Fig. 1).
6 A message appears containing data
regarding your cylinder; confirm this
with "OK" at the bottom right (Fig. 4).
2 The app displays a list of the cylinders
that have already been registered. This
is empty during the initial setup. Setup
a new cylinder by tapping on the "+" in
the top right-hand corner (Fig. 2).
7 In the following window, you will be
prompted to assign a name for the
cylinder. Where several cylinders and
secuENTRY components are used, it is
recommended to name the cylinder in
such a way that you can directly identify
what it is and where the cylinder is
located or attached. In the example in
these instructions, the cylinder is titled
"Front door cylinder". Confirm the name
with "OK" (Fig. 5).
Fig. 1
3 A prompt will appear asking you to scan
the cylinder QR code provided using
your smartphone camera (Fig. 3). The
QR code is on the sticker enclosed in
the packaging (Fig 4.).
Fig. 2
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Note: The randomly generated ad! ministrator
code can be found on the
enclosed QR code sticker under “ADM”.
(Fig. 9). The administrator code can be
changed at any time at a later date. Refer to the master operating instructions
on our website for an explanation on
this subject (see link on the title page).
QR
The set comes with two
! Attention:
QR code stickers, one for the cylinder
and one for the keypad. You can
identify the QR code required here
for the cylinder by the administrator
code at the bottom of the sticker,
marked "ADM" (Fig. 3).
8 A message appears informing you that
you can change your administrator
code. As you received a randomly generated administrator code at the time
of delivery, this step is optional. You can
bypass this with “Skip” (Fig. 6).
9 In order for the keypad to receive the
information on which cylinder it is to
control, this cylinder must be available
and assigned within the app.
Fig. 3
Cylinder QR code sticker
4 Tap on "Next" (Fig. 4). You may be
asked to confirm the app's access to
the camera.
Fig. 4
The next menu (Fig. 8) offers you the
following three options:
• „Link to an existing keypad“: You have
already setup a keypad in the app and
want to link it again.
• „Link to a new keypad“: You have
another keypad and want to link it to
the app.
• „Skip“: Carry out this step at a later
date.
QR
The keypad of the ENTRY 7601
! Note:
PIN set is already set up at the factory
and connected to the locking cylinder.
Consequently, you can skip this menu
item and continue directly to the next
chapter.
10 Tap on „Skip“ (Fig. 8).
6 I English
Fig. 9
Cylinder QR code sticker
secuENTRY easy | ENTRY 7601 PIN
6 Here you will be asked to verify yourself
with your administrator code. Enter the
code and confirm with “OK” (Fig. 5).
III - Locking plan
1 Use this menu to define the locking
plan, namely which user is allowed to
open which lock. The data is then transferred to the cylinder.
The factory administrator code
! Note:
can be found on the QR code sticker of
the cylinder under “ADM” (Fig. 9).
2 Open the “My System” menu (I) (Fig. 1).
3 Tap on the fourth menu item
“III - Locking plan” (Fig. 1).
I
I
II
Fig. 1
Fig. 2
info: This table is of interest when
! For
you have several cylinders and users.
This allows you to clearly determine
in one step who is allowed to access
which cylinder. Fig. 3 provides an
example of what a completed table
with corresponding cylinders and users
might look like.
II
9 You will be asked to set the keypad to
programming mode (Fig. 8). Instructions on how to do this can be found
in the chapter “Setting the keypad into
programming mode” on page 3. As soon
as the keypad is in programming mode,
indicated by the LEDs on the keypad
flashing continuously, tap the “LEDs
flashing continuously, continue” key in
the app (Fig. 8).
Fig. 5
Fig. 6
Fig. 7
Fig. 8
10 Nach einem kurzen Moment erhalten
Sie eine Rückmeldung, dass die Daten
übertragen wurden. Bestätigen Sie mit
„OK“.
The following step requires
! Attention:
the smartphone, keypad and cylinder
The setup is now completed.
Repeat the steps in the respective
chapters if you wish to integrate further
components into your system at a later
date, change access data or create
additional users.
to be in direct proximity to each other
(Bluetooth range).
5 If any changes have been made to
the locking plan, the display of the
respective cylinder appears red and
the „Program“ button is displayed. This
indicates that the settings have not yet
been transferred to the cylinder. To do
this, tap the red „Program“ button for
the respective cylinder (Fig. 4).
I
8 Select the required keypad (Fig. 7).
II
4 A table is displayed consisting of the
existing cylinders (horizontal) and
the configured users (vertical) (Fig. 2).
Select the checkbox where you wish to
authorise the respective user to use the
corresponding lock (I) (Fig. 2) and then
click on the button „Save changes“ (II)
(Fig. 2).
7 The data will be transferred. A confirmation will appear after a brief moment
and at the same time a request to now
assign the keypad. Tap on the confirmation message (Fig. 6).
Fig. 3
Fig. 4
Please note: All changes and additions
are carried out within the app and must
then be transferred to the respective
secuENTRY component. This last
chapter, “Locking plan” (page 8) must be
completed in each case in order to be
able to use them in your components.
QR
Fig. 9
QR-Code
Aufkleber Zylinder
7 I English
secuENTRY easy | ENTRY 7601 PIN
Opening the secuENTRY lock via the keypad (user code)
Using the cylinder and keypad
1 Activate the keypad by pressing either
the ON key or the CLOSE key (I) (Fig. 4).
To use the cylinder (Fig. 1) and
keypad (Fig. 2), remove the battery
protection strips.
Fig. 1
Fig. 2
Opening the secuENTRY lock
The ENTRY 7601 PIN set enables you to open the lock via the BURGsmart app or the keypad
using a user code, provided you have set up the corresponding opening media in accordance
with these instructions.
Opening the secuENTRY lock with the BURGsmart app
Further details on the history
! Note:
function can be found in the master
operating instructions on our website
(see link on the title page).
1 Open the BURGsmart app and press the
"ACCESS" button in the middle (Fig. 1).
DO NOT TAKE
OUT SCREWS
The BURGsmart app is pro! Note:
grammed so that when more than one
cylinder is used, it automatically adjusts
to the cylinder that is within the shortest distance of the smartphone. Each
cylinder can be opened by pressing the
"ACCESS" button.
!
Note: Further details on the subjects
of administrator and user codes can be
found in the chapters "QR code/administrator code" on page 2 and "I - User" on
page 4, as well asin the in the master
operating instructions on our website
(see link on the title page).
3 When the number combination entered
is correct, the cylinder status symbol
( ) will illuminate and the door can
be unlocked (Fig. 5) or locked (Fig. 6).
Low strength.
!
I
Fig. 4
Fig. 5
max. ca. 0,4 Nm
Note: Depending on the door stop, the
direction of rotation may be reversed.
DO NOT TAKE
OUT SCREWS
2 The cylinder is now released and the
lock can be opened (Fig. 2) or locked
(Fig. 3).
II
2 Enter your 6-digit administrator code or
programmed user code (II) (Fig. 4).
Proceed as follows to open the ENTRY
7600 CYL cylinder and consequently
also the door:
!
I
An entry "Opened" (ON button) or
"Closed" (CLOSE button) is generated in
the cylinder history. This allows for the
"Open" and "Close" operations to be
differentiated in the history.
Fig. 6
Low strength.
max. ca. 0,4 Nm
Fig. 1
Note: Depending on the door stop, the
direction of rotation may be reversed.
DO NOT TAKE
OUT SCREWS
Low strength.
max. ca. 0,4 Nm
Fig. 2
8 I English
Fig. 3
secuENTRY easy | ENTRY 7601 PIN
Opening the secuENTRY lock with the emergency lock
Assembly of the ENTRY easy 7600 CYL
The installation of the ENTRY easy
7600 CYL is explained below. Prior to
installation, please read the installation
instructions carefully.
Should the batteries in the locking
cylinder be completely discharged, the
lock can still be opened mechanically.
The emergency lock is located on the
outer side, below the knob attachment.
!
1 Remove the existing door lock cylinder
by loosening the forend screw in the
door and pulling out the cylinder with
the key inserted (Fig. 1).
Note: When the assembly steps in these
instructions have been completed, the
emergency lock is behind a cover and is
not directly visible.
1 To open the lock, open the emergency
key at the joint and then insert it
through the indicated slot on the
emergency lock cover (Fig. 11).
2 Turn the key 90 degrees clockwise.
If required, move the outside knob
slightly to the right and left in order
to release the mechanism. The lock is
open after at least two full turns of the
cylinder knob.
3 After opening the door, turn the emergency key back to its original position
(90 degrees counterclockwise) and
remove it.
4 To return the locking cylinder to its
regular locking position, turn the outside knob two complete turns in both
directions. This engages the mechanism
and the emergency lock is fully closed.
When the emergency lock is
! Note:
used, the keyhole indication on the
emergency lock cover is torn. A second
cover is included in the set so that it can
be replaced for aesthetic reasons.
9 I English
Fig. 11
Please note, the emergency
! Attention:
lock is designed for emergency openings
only. Please do not use it as a permanent
alternative to the standard locking options.
2 The loosening and fixing of the outer
and inner knob is achieved by means of
an integrated grub screw in the rotary
knob. Loosen the two grub screws
in the two knobs with the enclosed
hexagonal spanner (Fig. 2).
!
Attention: Use the long side of the
hexagonal spanner for this. Turn the
screw four times anticlockwise. Do not
remove the screws from the knob.
3 Pull off the knob on the outside completely and pull the knob on the inside
as far back as possible (Fig. 3).
!
Tip: The knob is in the inner side of the
battery compartment. Pay attention to
the battery compartment cover with
the screw hole (see diagram).
2.
Fig. 1
1.
4x
2 mm
DO NOT TAKE
OUT SCREWS
DO NOT TAKE
OUT SCREWS
Fig. 2
DO NOT TAKE
OUT SCREWS
The knob on the inside
! Attention:
cannot be pulled off. Do not try to loosen it by force, as pulling the knob from
the shaft will destroy the electronics.
The grub screw in the knob serves as
a pull-off protection.
Fig. 3
secuENTRY easy | ENTRY 7601 PIN
4 Adapters may be required depending on
the door thickness.
Door outer side
Door inner side
If the distance between the forend screw
and the outer side of the door (Fig. 4) is...
Forend screw
6 Screw the cylinder into the door and
push the inside and outside knobs up
to the door (Fig. 9).
• < 43 mm = no adapter required
(Fig. 5)
• 44 - 53 mm = Adapter 1 required
(Fig. 6)
Push adapter 1 onto the lock shaft
and screw it tight with the two
M2x10 screws provided.
Distance in mm
Fig. 4
Without adapter
Fig. 9
• 54 - 59 mm = Adapter 1 and 2 required
(Fig. 7)
After adapter 1 has been attached
(see above), then also push adapter 2
onto the lock shaft. Screw it tight with
the 2.9x13 screw provided.
Fig. 5
Adapter 1
DO NOT TAKE
OUT SCREWS
!
emergency lock cover is torn. A second
cover is included in the set so that it
can be replaced for aesthetic reasons.
min. 1 mm
Ensure that the
! ATTENTION:
knob is at least one millimetre
DO NOT TAKE
OUT SCREWSDO NOT TAKE
OUT SCREWS
Attention: Use the long side of
the hexagonal spanner for this.
Turn the screw
clockwise
DO NOT
TAKE with
OUT(max.
SCREWS
minimal force
torque approx. 0.4 Nm).
Low strength.
max. ca. 0,4 Nm
DO NOT TAKE
OUT SCREWS
Adapter 2
Note: Before assembling the cover,
the protective films of the adhesive
pads on the back of the cover must be
removed so that the three adhesive
pads securely fasten the cover to the
cut-out/door.
When the emergency lock is
! Note:
used, the keyhole indication on the
min. 1 mm
away from the door.
Fig. 6
5 From inside the door, push the cylinder
into the mortise lock. Push the emergency lock cover onto the outer side of
the locking shaft (Fig. 8).
7 Screw the grub screws back into
the two knobs (Fig. 10).
8 If you have not already done so,
remove the battery protection
strip from the battery compartment on the inside knob (Fig. 11).
2 mm
Low strength.
max. ca. 0,4 Nm
Low strength.
max. ca. 0,4 Nm
Low strength.
Fig. 10
max. ca. 0,4 Nm
Low strength.
max. ca. 0,4 Nm
Fig. 7
OUTDOOR
!
Fig. 11
INDOOR
1
3
2
< 43 mm = 1
44 - 53 mm = 2
54 - 59 mm = 3
10 I English
Fig. 8
secuENTRY easy | ENTRY 7601 PIN
ENTRY 7711 Keypad PIN installation - screw mounting
The installation of the ENTRY 7711 Keypad PIN is explained below.
There are two options to choose from for installation. The ENTRY 7711 Keypad PIN wall bracket
can either be screwed or adhered directly to the wall.
2 Insert the dowels supplied into
the holes and screw in the screws
provided (Fig. 2).
Prior to installation, please read the installation instructions carefully.
ENTRY 7711 Keypad PIN installation - function test prior to installation
40 mm
1 Drill three holes according to the
dimensions shown in the illustration.
Use a 6 mm diameter drill bit (Fig. 1).
61 mm
ENTRY 7711 Keypad PIN installation
! ATTENTION:
The distance between the cylinder and
the keypad can be up to a maximum
of four metres. This distance may vary,
however, depending on external conditions. In order to ensure that the keypad
functions correctly in the desired
position, we recommend testing it first
before installation.
Ø 6 mm
Fig. 2
3 Remove the screw from the bottom of
the keypad using the Tx8 screwdriver
supplied with the keypad and pull
the battery compartment downwards
(Fig. 3).
max. 4 m
1 Place the keypad in the desired installation location (Fig. 1).
Fig. 1
2 Enter your administrator or user code
and check that the cylinder is activated
(Fig. 2).
Fig. 3
The administrator code, if you ha! Note:
ven't already changed it, can be found
QR
on the QR code sticker enclosed with
the secuENTRY cylinder (Fig. 3). For information on how to create a user code,
see the chapter "I - User" on page 4.
3 If the cylinder activates, the signal
strength is sufficient and the keypad
can be installed in the desired location.
If not, try again with a shorter distance
between cylinder and keypad.
Fig. 1
Fig. 2
4 Place the keypad on the screw heads as
shown in the illustration (Fig. 4).
Fig. 3:
QR code sticker for
secuENTRY cylinder.
Factory-assigned
administrator code
Fig. 4
5 Insert the battery compartment back
into the housing and screw it tight
(Fig. 5).
Fig. 5
11 I English
secuENTRY easy | ENTRY 7601 PIN
ENTRY 7711 Keypad PIN installation - adhesive mounting
Battery status display and replacing the batteries
1 Clean the surface to which the keypad
is to be attached (Fig. 6).
ENTRY 7600 CYL cylinder
The battery status is shown on the
display each time a secuENTRY cylinder
is activated via the BURGsmart app
(Fig. 1). When the batteries in the
cylinder are running low, replace them
as soon as possible.
Fig. 6
2 Attach the enclosed adhesive pads to
the positions shown in the illustration
and peel off the backing strips (Fig. 7).
The batteries are located in the
! Note:
cylinder knob on the inside of the
door. If the battery status is ignored
and the batteries become completely
discharged, you can only open the
cylinder from the outside using the
emergency lock. For further information, please refer to chapter "Opening
the secuENTRY lock with the emergency
lock" on page 9.
Instructions on replacing the batteries
are given below:
Fig. 1
Fig. 7
TX8
1 Using the TX8 screwdriver provided,
loosen the screw on the inner side of
the door at the front end of the knob
and open the cover. The screw can only
be unscrewed up to the opening of the
cover and will not fall out. (Fig. 2).
3 Mount the keypad on the wall in the
desired position (Fig. 8).
Fig. 2
2 Remove the old batteries and dispose
of them appropriately.
Fig. 8
Instructions for proper disposal
! Tip:
can be found on page 14 of these
instructions.
3 Insert two new batteries. Make sure that
the polarity is correct according to the
drawing (Fig. 3).
4 Press the keypad against the wall for
approx. one minute (Fig. 9).
! Attention:
Only press the outer edges of the hous-
ing. To avoid damage to the electronics,
do not press within the keypad area.
Fig. 3
1 Min.
4 Replace the front cover and screw it on
tightly (Fig. 4).
!
Fig. 9
TX8
Fig. 4
12 I English
secuENTRY easy | ENTRY 7601 PIN
Compatibility with other secuENTRY products
ENTRY 7711 Keypad PIN
Whether for one front door, several doors or a complete locking system: Simply configure your
individual unit with the secuENTRY modular system.
The system monitors the keypad and
cylinder battery voltage. The user is
alerted as soon as the battery voltage
reaches a critical range. Batteries must
be changed as soon as possible after
the battery status symbol illuminates
on the keypad (Fig. 5).
Your ENTRY 7600 CYL cylinder can be extended with the following components:
secuENTRY Keypad
ENTRY 7711 PIN / 7712 FP
It is recommended that the
! Tip:
batteries in the cylinder and keypad
are always replaced at the same time.
Nonetheless, the battery status of the
cylinder can be checked separately at
any time. The current battery status is
displayed on the BURGsmart app main
screen (Fig. 6).
Instructions on replacing the batteries
are given below:
Fig. 1
Fig. 5
Fig. 6
A keypad ENTRY 7711 Keypad PIN is
already included in this ENTRY 7601
PIN set.
Further information
can be found on
our website:
www.burg.biz
ENTRY 7712 FP:
4003482507124
www.burg.biz
ENTRY 7722 FP:
4003482507223
Further information
can be found on
our website:
www.burg.biz
Fig. 2
secuENTRY Radio key
ENTRY sE-Key 7713
Tip: Instructions for proper disposal
can be found on page 15 of these
instructions.
Fig. 7
Fig. 8
Fig. 3
3 Insert two new batteries. Make sure that
the polarity is correct according to the
drawing (Fig. 9).
The cylinder is opened simply by
pressing a button using the ENTRY
sE-Key 7713 radio key. The transmission is encrypted at a high security
level (AES encryption).
secuENTRY Transponder
ENTRY 7710 RFID
Insert the battery compartment back
into the housing and screw it tight
(Fig. 10).
Fig. 4
Fig. 9
13 I English
Further information
can be found on
our website:
The ENTRY 7722 FP display keypad
enables opening with a 6-digit user
code or fingerprint.
2 Remove the old batteries and dispose
of them appropriately.
!
Using the ENTRY 7711 Keypad PIN,
you can unlock and lock the door
with a 6-digit user code. In addition,
with the ENTRY 7712 Keypad FP also
with fingerprint.
secuENTRY Keypad
ENTRY 7722 FP
1 Remove the screw from the bottom
of the keypad using the Tx8
screwdriver supplied (Fig. 7) with
the keypad and pull the battery
compartment downwards (Fig. 8).
ENTRY 7711 PIN:
4003482507117
The modern passive transponder
provides door opening with contactless data transmission.
Attention: The ENTRY 7174 RFID
Extender add-on is additionally
required for use with the
ENTRY 7600 CYL cylinder.
Article number:
4003482507131
Further information
can be found on
our website:
www.burg.biz
Article number:
4003482568200
Further information
can be found on
our website:
www.burg.biz
Fig. 10
secuENTRY easy | ENTRY 7601 PIN
secuENTRY Add-on
ENTRY 7174 RFID-Extender
RFID transponder reader. Can be used
for cylinders or, in conjunction with
an ENTRY 7171 Relay, for external
electronic devices.
Warranty
Article number:
4003482501740
Further information
can be found on
our website:
www.burg.biz
When returning goods due to your right of withdrawal, all parts of the appliance must also be in
their factory settings. Failure to comply with this will invalidate the warranty.
Fig. 5
secuENTRY Add-on
ENTRY 7171 Relay
Fig. 6
Control unit for switching external
electronic devices (shutters, barriers,
light sources, etc.).
secuENTRY Add-on
ENTRY 5670 Bridge
Fig. 7
Your new found freedom: Using the
secuENTRY Bridge via the internet
you can open your door even when
you are out and about.
secuENTRY Add-on
ENTRY 7172 REMOTE
For automatic remote activation.
Control of electronic garage motors,
alarm systems, etc.
In order to deliver a flawless and high quality product to you and to better assist you in case of
service or repair, it is necessary that faulty or defective devices along with the valid administrator
code and the QR code(s) be presented to your dealer together with the original documentation.
Article number:
4003482506707
Further information
can be found on
our website:
Disposal of the device
www.burg.biz
Please help to reduce waste. Should you intend to dispose of this device at any time, please remember that many components of this device contain valuable materials that can be recycled.
Article number:
4003482562802
Further information
can be found on
our website:
www.burg.biz
Article number:
4003482501726
Further information
can be found on
our website:
Article number:
4003482507506
Provides convenient user management of up to 15 users and 8 locks.
Further information
can be found on
our website:
secuENTRY Windows-Software
ENTRY 7783 Software Pro
Article number:
4003482507834
lease note that electrical and electronic devices as well as batteries must not be
P
disposed of with household waste but rather apart from it or separately. Please obtain
information on the collecting points for electrical waste from the responsible authority
of your city/municipality.
URG-WÄCHTER KG hereby declares that this device complies with the Directives
B
2014/53/EU, (RED) and 2011/65/EU (RoHS).
www.burg.biz
The complete text of the EU Declaration of Conformity is available at the following
Internet address https://burg.biz/pages/eu-konformitaetserklaerung.
Fig. 8
secuENTRY Windows-Software
ENTRY 7750 Software Light
Dear customer,
www.burg.biz
Fig. 9
Fig. 10
Designed specifically for companies
and public authorities. Allowing the
management of up to 2,000 users
and up to 1,000 doors per client
(database) or up to 500 doors in
hotel mode.
Further information
can be found on
our website:
www.burg.biz
Printing and typesetting errors as well as technical changes reserved.
14 I English
secuENTRY easy | ENTRY 7601 PIN
BD Initial setup ENTRY easy 7601 PIN EN HBG/SWI 030723
secuENTRY easy
ENTRY 7601 PIN
BURG-WÄCHTER KG
Altenhofer Weg 15
58300 Wetter
Germany
www.burg.biz
www.burg.biz
">