NEC projector Reference manual

ಪಿಡಿಎಫ್

ದಾಖಲೆ

ಜಾಹಿರಾತು

Projector

Control Command

Reference Manual

Revision 4.0

Introduction

This manual describes the commands used to control an NEC-made projector from a PC or other external device. A projector can be controlled by exchanging commands with an external device connected via a serial port or network.

The manual assumes basic knowledge of projectors. For information about the functions of the model in use and how to adjust the device, see the operation manual of the projector .For information about the connection between the projector and an external device, see "1 Connecting an External Device" (page 5). Connect an external device as appropriate for the usage environment of the projector.

Models for which the control commands are available

See the Appendix "Connecting an External Device".

Conventions

For information about how commands and responses are expressed in this manual, see "2.1 Understanding command details" (page 10).

NOTES

1. The contents of this reference manual may not be reprinted in part or whole without permission.

2. The contents of this reference manual are subject to change without notice.

3. Great care has been taken in the preparation of this reference manual; however, should you notice any questionable points, errors or omissions, please contact us.

4. Notwithstanding article 3. NEC will not be responsible for any claims on loss of profit or other matters deemed to result from using this reference manual.

Projector Control Command Reference Manual ........................................................................... 1

Introduction ............................................................................................................................................................... 2

Contents ................................................................................................................................................................... 3

Connecting an External Device ............................................................................................... 5

1.1

Connection interface ...................................................................................................................................... 5

1.2

Communication conditions ............................................................................................................................. 7

Command List .......................................................................................................................... 8

2.1

Understanding command details ...................................................................................................................10

2.2

Parameters...................................................................................................................................................10

2.3

Responses ................................................................................................................................................... 11

2.4

Error code list ...............................................................................................................................................12

Command details ................................................................................................................... 13

3.1

[ 009. ERROR STATUS REQUEST ] .............................................................................................................13

3.2

[ 015. POWER ON ] ......................................................................................................................................15

3.3

[ 016. POWER OFF ] ....................................................................................................................................16

3.4

[ 018. INPUT SW CHANGE ] .........................................................................................................................17

3.5

[ 020. PICTURE MUTE ON ] .........................................................................................................................19

3.6

[ 021. PICTURE MUTE OFF ] .......................................................................................................................20

3.7

[ 022. SOUND MUTE ON ] ............................................................................................................................21

3.8

[ 023. SOUND MUTE OFF ] ..........................................................................................................................22

3.9

[ 024. ONSCREEN MUTE ON ] .....................................................................................................................23

3.10

[ 025. ONSCREEN MUTE OFF ] ...................................................................................................................24

3.11

[ 030-1. PICTURE ADJUST ] .........................................................................................................................25

3.12

[ 030-2. VOLUME ADJUST ] .........................................................................................................................27

3.13

[ 030-12. ASPECT ADJUST ].........................................................................................................................29

3.14

[ 030-15. OTHER ADJUST ] ..........................................................................................................................30

3.15

[ 037. INFORMATION REQUEST ] ................................................................................................................32

3.16

[ 037-3. FILTER USAGE INFORMATION REQUEST ] ...................................................................................33

3.17

[ 037-4. LAMP INFORMATION REQUEST 3 ] ................................................................................................34

3.18

[ 037-6. CARBON SAVINGS INFORMATION REQUEST ] .............................................................................36

3.19

[ 050. REMOTE KEY CODE ] ........................................................................................................................38

3.20

[ 053. LENS CONTROL ] ..............................................................................................................................40

3.21

[ 053-1. LENS CONTROL REQUEST ] ..........................................................................................................42

3.22

[ 053-2. LENS CONTROL 2 ].........................................................................................................................44

3.23

[ 053-3. LENS MEMORY CONTROL ] ...........................................................................................................46

3.24

[ 053-4. REFERENCE LENS MEMORY CONTROL ] .....................................................................................48

3.25

[ 053-5. LENS MEMORY OPTION REQUEST ] .............................................................................................50

3.26

[ 053-6. LENS MEMORY OPTION SET ] .......................................................................................................51

3.27

[ 053-7. LENS INFORMATION REQUEST ] ...................................................................................................53

3.28

[ 053-10. LENS PROFILE SET ] ....................................................................................................................54

3.29

[ 053-11. LENS PROFILE REQUEST ] ..........................................................................................................55

3.30

[ 060-1. GAIN PARAMETER REQUEST 3 ] ...................................................................................................56

3.31

[ 078-1. SETTING REQUEST ] ......................................................................................................................58

3.32

[ 078-2. RUNNING STATUS REQUEST ] .......................................................................................................59

3.33

[ 078-3. INPUT STATUS REQUEST ] ............................................................................................................60

3.34

[ 078-4. MUTE STATUS REQUEST ] .............................................................................................................62

3.35

[ 078-5. MODEL NAME REQUEST ] ..............................................................................................................64

3.36

[ 078-6. COVER STATUS REQUEST ] ..........................................................................................................65

3.37

[ 079. FREEZE CONTROL ] ..........................................................................................................................66

3.38

[ 084. INFORMATION STRING REQUEST ] ..................................................................................................67

3.39

[ 097-8. ECO MODE REQUEST ] ..................................................................................................................68

3.40

[ 097-45. LAN PROJECTOR NAME REQUEST ] ...........................................................................................69

3.41

[ 097-155. LAN MAC ADDRESS STATUS REQUEST2 ] ................................................................................70

3.42

[ 097-198. PIP/PICTURE BY PICTURE REQUEST ] ......................................................................................71

3.43

[ 097-243-1. EDGE BLENDING MODE REQUEST ] ......................................................................................73

3.44

[ 098-8. ECO MODE SET ] ............................................................................................................................74

3.45

[ 098-45. LAN PROJECTOR NAME SET ] .....................................................................................................75

3.46

[ 098-198. PIP/PICTURE BY PICTURE SET ] ................................................................................................76

3.47

[ 098-243-1. EDGE BLENDING MODE SET ] ................................................................................................78

3.48

[ 305-1. BASE MODEL TYPE REQUEST ] .....................................................................................................79

3.49

[ 305-2. SERIAL NUMBER REQUEST ] .........................................................................................................80

3.50

[ 305-3. BASIC INFORMATION REQUEST ] ..................................................................................................81

3.51

[ 319-10. AUDIO SELECT SET ] ....................................................................................................................83

Revision History ..................................................................................................................... 85

Connecting an External Device

This chapter describes how to connect the projector to an external device and communication conditions.

1.1 Connection interface

The projector can be connected to a PC or other external device using the methods mentioned below.

For information about the connection method supported by the model in use, see the Appendix "Connecting an

External Device".

・ Connection using a serial port

・ Connection via a network

Connection using a serial port

This method connects a PC and the projector using a serial cable (cross cable).

Connect the serial cable to the PC CONTROL port of the projector. The pin assignment of the serial cable is shown below.

Projector Pin number

(Not used)

RxD

TxD

(Not used)

GND

(Not used)

RTS

CTS

(Not used)

External device

(Not used)

TxD

RxD

(Not used)

GND

(Not used)

CTS

RTS

(Not used)

Connection via a network

Information

・ Before connecting an external device via a network, check with the network administrator.

・ Some models cannot receive commands in standby mode. See Appendix "Standby Mode setting for receiving commands".

4 Connection using a wired LAN

This method connects a PC and the projector using a LAN cable. For information about the type of LAN cable to be used (straight or cross), contact the network administrator. The pin assignment of the LAN port is shown below.

Pin number

－

RD-

－

Function

TD+

TD-

RD+

－

Description

Transmit Data (+)

Transmit Data (-)

Receive Data (+)

Not used

Receive Data (-)

Not used

4 Connection using a wireless LAN

This method connects a PC via a wireless LAN by connecting a wireless LAN unit to the projector. For information about the available wireless LAN units, see the operation manual of the model in use.

1.2 Communication conditions

For information about the connection methods available for the model in use, see the Appendix "Connecting an

External Device".

Serial connection

The RS-232C-compliant communication method is supported. Specify the communication settings of the software used to send and receive commands, as shown below.

Detail Item

Baud rate

Data length

Parity bit

Stop bit

Communication mode

115200/38400/19200/9600/4800 bps

8 bits

None

1 bit

Full duplex

LAN connection

4 Wired LAN

Item

Data rate

Supported standard

Detail

Auto switchable (10/100 Mbps)

IEEE802.3 (10BASE-T)

IEEE802.3u (100BASE-TX, Auto-Negotiation)

4 Wireless LAN

See the operation manual of the wireless LAN unit to be used.

4 Port number

Use TCP port number "7142" for sending and receiving commands.

Command List

Command Description

009. ERROR STATUS REQUEST

015. POWER ON

016. POWER OFF

018. INPUT SW CHANGE

020. PICTURE MUTE ON

021. PICTURE MUTE OFF

022. SOUND MUTE ON

023. SOUND MUTE OFF

024. ONSCREEN MUTE ON

025. ONSCREEN MUTE OFF

030-1. PICTURE ADJUST

030-2. VOLUME ADJUST

030-12. ASPECT ADJUST

060-1. GAIN PARAMETER REQUEST 3

Gets information about errors occurring in the projector.

Turns on the power of the projector.

Turns off the power of the projector.

Switches the input terminal or entry list.

Turns the picture mute on.

Turns the picture mute off.

Turns the sound mute on.

Turns the sound mute off.

Turns the onscreen mute on.

Turns the onscreen mute off.

Adjusts the picture.

Adjusts the sound volume.

Adjusts the aspect.

030-15. OTHER ADJUST

037. INFORMATION REQUEST

037-3. FILTER USAGE INFORMATION REQUEST

Adjusts the various gains.

Gets the information of the projector.

Gets filter usage information such as usage time.

037-4. LAMP INFORMATION REQUEST 3 Gets lamp information such as usage time and remaining life.

037-6. CARBON SAVINGS INFORMATION REQUEST Gets the Carbon Saving values on the projector.

050. REMOTE KEY CODE

053. LENS CONTROL

053-1. LENS CONTROL REQUEST

053-2. LENS CONTROL 2

053-3. LENS MEMORY CONTROL

053-4. REFERENCE LENS MEMORY CONTROL

053-5. LENS MEMORY OPTION REQUEST

Sends the key code for remote control.

Adjusts the lens position.

Gets adjusted values of the lens position.

Adjusts the lens position.

Controls the lens memory.

Controls the reference lens memory.

Gets the value set for the lens memory.

053-6. LENS MEMORY OPTION SET

053-7. LENS INFORMATION REQUEST

053-10. LENS PROFILE SET

053-11. LENS PROFILE REQUEST

Sets the lens memory.

Gets information about the lens of the projector.

Selects the profile number of the reference lens memory.

Gets the selected profile number of the reference lens memory.

Gets adjusted values of the picture, volume, and backlight.

Page to

29 see

Command

078-1. SETTING REQUEST

078-2. RUNNING STATUS REQUEST

078-3. INPUT STATUS REQUEST

078-4. MUTE STATUS REQUEST

078-5. MODEL NAME REQUEST

078-6. COVER STATUS REQUEST

079. FREEZE CONTROL

084. INFORMATION STRING REQUEST

097-8. ECO MODE REQUEST

097-45. LAN PROJECTOR NAME REQUEST

097-155. LAN MAC ADDRESS STATUS REQUEST2

097-198. PIP/PICTURE BY PICTURE REQUEST

097-243-1. EDGE BLENDING MODE REQUEST

098-8. ECO MODE SET

098-45. LAN PROJECTOR NAME SET

098-198. PIP/PICTURE BY PICTURE SET

098-243-1. EDGE BLENDING MODE SET

305-1. BASE MODEL TYPE REQUEST

305-2. SERIAL NUMBER REQUEST

305-3. BASIC INFORMATION REQUEST

319-10. AUDIO SELECT SET

Description

Gets information of the projector.

Gets the information about the operation status of the projector.

Gets the information about the input signal status of the projector.

Gets the mute status of the projector.

Gets the model name of the projector.

Gets the status of the mirror cover or lens cover.

Controls whether to turn the freeze function on or off.

Gets information strings (English) displayed on the projector.

Gets the value set for the eco mode.

Gets the projector name.

Gets the MAC address of the projector.

Gets the value set for the picture in picture and picture by picture.

Gets the value set for the edge blending.

Sets the eco mode.

Sets the projector name.

Sets the picture in picture or picture by picture.

Sets the edge blending.

Gets the base model type of the projector.

Gets the serial number of the projector.

Gets the operation status of the projector.

Sets the audio select.

Page to see

2.1 Understanding command details

In this manual, commands and responses are expressed as follows.

20h 88h <ID1> <ID2> 0Ch <DATA01> - <DATA12> <CKS>

Command/response

Parameter

A series of strings enclosed in a frame represents a command or response (in hexadecimal notation).

A character string in italic enclosed in brackets represents a parameter.

For information about the parameters that are common to the control commands

(ID1, ID2, CKS, LEN, ERR1, and ERR2), see "2.2 Parameters" (page 10). For information about those parameters whose content varies from command to command (DATA), see the description of the relevant command.

2.2 Parameters

The parameters that are used in the control commands are listed below.

Parameter name Description

ID1

ID2

CKS

LEN

Control ID

Model code

Checksum

The value of the "control ID" set for the projector is used.

This varies depending on the model in use.

The checksum is calculated as follows.

① Add all preceding bytes of data.

② Use the value of the low-order one byte (eight bits) of the addition result obtained in ① as the checksum.

Data length This indicates the data length of the data part (DATA??) following LEN (in bytes).

Variable length data This varies depending on the character string stored. DATA??

ERR1

ERR2

Response error

Example of checksum calculation

The cause of an error is represented by a combination of error codes.

For information about error codes, see "2.4 Error code list" (page 12).

20h 81h 01h 60h 01h 00h <CKS>

① Add all the data preceding the checksum.

"20h + 81h + 01h + 60h + 01h + 00h = 103h"

② Use the low-order one byte "03h" of the addition result obtained in ① as the checksum.

2.3 Responses

After a command is sent to the projector, its result is returned as a response. How a response is returned differs depending on the execution result of the command.

When the execution of a command succeeds

When the command does not request data, a response is returned with no data part.

When the command requests data, a response is returned with data added to data parts.

When the execution of a command fails

A response is returned with the cause of the failed command execution indicated in <ERR1> and <ERR2>.

(Example) POWER ON

4 Command

02h 00h 00h 00h 00h 02h

4 Response

A2h 00h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

2.4 Error code list

The following table lists the combinations of error codes (ERR1 and ERR2) and describes the error indicated by each combination.

0Ch

0Dh

0Eh

0Fh

00h

01h

02h

04h

06h

07h

08h

09h

0Ah

ERR2

00h

01h

00h

01h

02h

00h

02h

03h

02h

03h

02h

ERR1

00h

01h

02h

Error description

The command cannot be recognized.

The command is not supported by the model in use.

The specified value is invalid.

The specified input terminal is invalid.

The specified language is invalid.

Memory allocation error

Memory in use

The specified value cannot be set.

Forced onscreen mute on

Viewer error

No signal

A test pattern or filer is displayed.

No PC card is inserted.

Memory operation error

An entry list is displayed.

The command cannot be accepted because the power is off.

The command execution failed.

There is no authority necessary for the operation.

The specified gain number is incorrect.

The specified gain is invalid.

Adjustment failed.

Command details

3.1 [ 009. ERROR STATUS REQUEST ]

Gets information about errors occurring in the projector.

Command

00h 88h 00h 00h 00h 88h

Response

4 When the command succeeds

20h 88h <ID1> <ID2> 0Ch <DATA01> - <DATA12> <CKS>

4 When the command fails

A0h 88h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

Data part

DATA1 - DATA12 ............. Error information is provided. A bit set to "0" indicates that the data is normal, and a bit set to "1" indicates an error. For an error information list, see the next page.

DATA01

Item

DATA02

DATA03

DATA04

DATA05 - 08

DATA09

DATA10 - 12

Description

Error status (1)

Bit0

Bit1

Bit2

Cover error

Temperature error (bi-metallic strip)

None (fixed to 0)

Bit4

Bit5

Bit6

Fan error

Power error

Lamp (or lamp 1) off or backlight off

Lamp (or lamp 1) in a replacement moratorium

Bit3 Fan error Bit7

Error status (2)

Bit0 Lamp (or lamp 1) usage time exceeded the limit

Bit1 Formatter error

Bit2

Bit3

Lamp 2 off

None (fixed to 0)

Error status (3)

Bit0 None (fixed to 0)

Bit1

Bit2

Bit3

FPGA error

Temperature error (temperature sensor)

Lamp (or lamp 1) not present

Bit4

Bit5

Bit6

Bit7

Bit4

Bit5

Bit6

Bit7

Error status (4)

Bit0 Lamp 2 not present

Bit1 Lamp 2 data error

Bit2

Bit3

Temperature error due to dust

Foreign matter sensor error

Reserved for the system

Extended status

Bit0 The portrait cover side is up

Bit1 The interlock switch is open.

Bit2

Bit3

System error has occurred.

(Slave CPU)

System error has occurred

(Formatter)

Reserved for the system

Bit7

Bit4

Bit5

Bit6

Bit7

Bit4

Bit5

Bit6

None (fixed to 0)

Refer to the extend status.

Lamp (or lamp 1) data error

Mirror cover error

Lamp 2 in a replacement moratorium

Lamp 2 usage time exceeded the limit

None (fixed to 0)

Ballast communication error

Iris calibration error

The lens is not installed properly.

None (fixed to 0)

3.2 [ 015. POWER ON ]

Turns on the power of the projector.

Information

While this command is turning on the power, no other command can be accepted.

Command

02h 00h 00h 00h 00h 02h

Response

4 When the command succeeds

22h 00h <ID1> <ID2> 00h <CKS>

4 When the command fails

A2h 00h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.3 [ 016. POWER OFF ]

Turns off the power of the projector.

Information

While this command is turning off the power (including the cooling time), no other command can be accepted.

Command

02h 01h 00h 00h 00h 03h

Response

4 When the command succeeds

22h 01h <ID1> <ID2> 00h <CKS>

4 When the command fails

A2h 01h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.4 [ 018. INPUT SW CHANGE ]

Switches the input terminal or entry list.

Command

02h 03h 00h 00h 02h 01h <DATA01> <CKS>

Data part

Item Description

DATA01 Input terminal

Information

For the values of input terminal, see the Appendix "Supplementary Information by Command".

4 Command example

The following command switches the input terminal to a video port (DATA01: 06h).

02h 03h 00h 00h 02h 01h 06h 0Eh

Response

4 When the command succeeds

22h 03h <ID1> <ID2> 01h <DATA01> <CKS>

Data part

DATA01

Item

4 When the command fails

Description

Execution result

00h

FFh

Ended successfully.

Ended with an error (no signal switch is made).

A2h 03h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.5 [ 020. PICTURE MUTE ON ]

Turns the picture mute on.

Information

If any of the following operations is done, the picture mute is turned off.

・ Input terminal switch

・ Video signal switch

Command

02h 10h 00h 00h 00h 12h

Response

4 When the command succeeds

22h 10h <ID1> <ID2> 00h <CKS>

4 When the command fails

A2h 10h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.6 [ 021. PICTURE MUTE OFF ]

Turns the picture mute off.

Command

02h 11h 00h 00h 00h 13h

Response

4 When the command succeeds

22h 11h <ID1> <ID2> 00h <CKS>

4 When the command fails

A2h 11h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.7 [ 022. SOUND MUTE ON ]

Turns the sound mute on.

Information

If any of the following operations is done, the sound mute is turned off.

・ Input terminal switch

・ Video signal switch

・ Sound volume adjustment

Command

02h 12h 00h 00h 00h 14h

Response

4 When the command succeeds

22h 12h <ID1> <ID2> 00h <CKS>

4 When the command fails

A2h 12h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.8 [ 023. SOUND MUTE OFF ]

Turns the sound mute off.

Command

02h 13h 00h 00h 00h 15h

Response

4 When the command succeeds

22h 13h <ID1> <ID2> 00h <CKS>

4 When the command fails

A2h 13h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.9 [ 024. ONSCREEN MUTE ON ]

Turns the onscreen mute on.

Information

If any of the following operations is done, the onscreen mute is turned off.

・ Input terminal switch

・ Video signal switch

Command

02h 14h 00h 00h 00h 16h

Response

4 When the command succeeds

22h 14h <ID1> <ID2> 00h <CKS>

4 When the command fails

A2h 14h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.10 [ 025. ONSCREEN MUTE OFF ]

Turns the onscreen mute off.

Command

02h 15h 00h 00h 00h 17h

Response

4 When the command succeeds

22h 15h <ID1> <ID2> 00h <CKS>

4 When the command fails

A2h 15h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.11 [ 030-1. PICTURE ADJUST ]

Adjusts the picture.

Command

03h 10h 00h 00h 05h <DATA01> FFh <DATA02> - <DATA04> <CKS>

Data part

DATA01

DATA02

Item Description

Adjustment target

00h

01h

02h

03h

Brightness

Contrast

Color

Hue

04h

Adjustment mode

00h

Sharpness

Specify an absolute value

01h Specify a relative value

Adjustment value (low-order 8 bits)

Adjustment value (high-order 8 bits)

DATA03

DATA04

4 Command example

① The following command sets brightness to "10".

03h 10h 00h 00h 05h 00h FFh 00h 0Ah 00h 21h

② The following command sets brightness to "-10".

03h 10h 00h 00h 05h 00h FFh 00h F6h FFh 0Ch

Response

4 When the command succeeds

23h 10h <ID1> <ID2> 02h <DATA01> <DATA02> <CKS>

Data part

DATA01

DATA02

Item

4 When the command fails

Description

Execution result

0000h Ended successfully.

Other than 0000h Ended with an error.

A3h 10h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.12 [ 030-2. VOLUME ADJUST ]

Adjusts the sound volume.

Command

03h 10h 00h 00h 05h 05h 00h <DATA01> - <DATA03> <CKS>

Data part

DATA01

Item Description

Adjustment mode

00h

01h

Specify an absolute value

Specify a relative value

Adjustment value (low-order 8 bits)

Adjustment value (high-order 8 bits)

DATA02

DATA03

4 Command example

The following command set the sound volume to "10".

03h 10h 00h 00h 05h 05h 00h 00h 0Ah 00h 27h

Response

4 When the command succeeds

23h 10h <ID1> <ID2> 02h <DATA01> <DATA02> <CKS>

Data part

DATA01

DATA02

Item

4 When the command fails

Description

Execution result

0000h Ended successfully.

Other than 0000h Ended with an error.

A3h 10h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.13 [ 030-12. ASPECT ADJUST ]

Adjusts the aspect.

Command

03h 10h 00h 00h 05h 18h 00h 00h <DATA01> 00h <CKS>

Data part

Item Description

DATA01 Value set for the aspect

Information

For information about the values set for the aspect, see the Appendix "Supplementary Information by

Command".

Response

4 When the command succeeds

23h 10h <ID1> <ID2> 02h <DATA01> <DATA02> <CKS>

Data part

DATA01

DATA02

Item

4 When the command fails

Description

Execution result

0000h Ended successfully.

Other than 0000h Ended with an error.

A3h 10h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.14 [ 030-15. OTHER ADJUST ]

Adjusts the various gains.

Command

03h 10h 00h 00h 05h <DATA01> - <DATA05> <CKS>

Data part

DATA01

DATA02

DATA03

Item

DATA04

DATA05

DATA01

96h

Adjustment mode

00h

01h

DATA02

FFh

Description

Adjustment target

LAMP ADJUST / LIGHT ADJUST

Specify an absolute value

Specify a relative value

Adjustment value (low-order 8 bits)

Adjustment value (high-order 8 bits)

Response

4 When the command succeeds

23h 10h <ID1> <ID2> 02h <DATA01> <DATA02> <CKS>

Data part

DATA01

DATA02

Item

4 When the command fails

Description

Execution result

0000h Ended successfully.

Other than 0000h Ended with an error.

A3h 10h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.15 [ 037. INFORMATION REQUEST ]

Gets the information of the projector.

Command

03h 95h 00h 00h 00h 98h

Response

4 When the command succeeds

23h 8Ah <ID1> <ID2> 62h <DATA01> - <DATA98> <CKS>

Data part

Item

DATA01 - 49

DATA50 - 82

DATA83 - 86

DATA87 - 90

DATA91 - 98

4 When the command fails

Description

Projector name (NUL: termination character string).

Reserved for the system

Lamp usage time (seconds)

Filter usage time (seconds)

Reserved for the system

A3h 8Ah <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

4 Response example

When the lamp usage time is18000 seconds (5 hours)

23h 8Ah <ID1> <ID2> 62h <DATA01> - <DATA82> 50h 46h 00h 00h

<DATA87> - <DATA98> <CKS>

Lamp usage time (DATA83 – DATA86) = 18000 / 3600 = 5 hours

Information

While the usage time can be obtained in one-second units, the information is updated at one-minute intervals.

3.16 [ 037-3. FILTER USAGE INFORMATION REQUEST ]

Gets filter usage information such as usage time.

Command

03h 95h 00h 00h 00h 98h

Response

4 When the command succeeds

23h 95h <ID1> <ID2> 08h <DATA01> - <DATA08> <CKS>

Data part

Item

DATA01 - 04

DATA05 - 08

Filter usage time (seconds)

Filter alarm start time (seconds)

Information

If no time is defined, "-1" is returned.

4 When the command fails

Description

A3h 95h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.17 [ 037-4. LAMP INFORMATION REQUEST 3 ]

Gets lamp usage information such as usage time or remaining life. When the eco mode is enabled, the values in the obtained information reflect the eco mode.

Command

03h 96h 00h 00h 02h <DATA01> <DATA02> <CKS>

Data part

Item Description

DATA01

DATA02

Target

00h

01h

Content

01h

04h

Lamp 1

Lamp 2

Lamp usage time (seconds)

Lamp remaining life (%)

Information

"01h" (Lamp 2) in DATA01 is effective only for two-lamp projector models.

4 Command example

The following command gets the lamp usage time.

03h 96h 00h 00h 02h 00h 01h 9Ch

Response

4 When the command succeeds

23h 96h <ID1> <ID2> 06h <DATA01> - <DATA06> <CKS>

Data part

DATA01

Item

DATA02

DATA03 - 06

4 When the command fails

Description

Target

00h

01h

Content

01h

Lamp 1

Lamp 2

Lamp usage time (seconds)

04h

Obtained information

Lamp remaining life (%)

A3h 96h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

4 Response example

When the lamp usage time is18000 seconds (5 hours)

23h 96h <ID1> <ID2> 06h 00h 01h 50h 46h 00h 00h <CKS>

Lamp usage time (DATA03 - DATA06) = 18000 / 3600 = 5 hours

Information

・ While the lamp usage time can be obtained in one-second units, the information is updated at one-minute intervals.

・ If the lamp replacement deadline is exceeded, a negative value is returned as the lamp remaining life (%).

3.18 [ 037-6. CARBON SAVINGS INFORMATION REQUEST ]

Gets the Carbon Saving values on the projector.

Command

03h 9Ah 00h 00h 01h <DATA01> <CKS>

Data part

DATA01

Item

Target

00h

01h

Description

Total Carbon Savings

Carbon Savings during operation

Response

4 When the command succeeds

23h 9Ah <ID1> <ID2> 09h <DATA01> - <DATA09> <CKS>

Data part

DATA01

Item

DATA02 - 05

DATA06 - 09

4 When the command fails

Description

Target

00h Total Carbon Savings

01h Carbon Savings during operation

Carbon Savings (Kilogram Maximum: 99999[kg])

Carbon Savings (Milligram Maximum:999999[mg])

A3h 9Ah <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

4 Response example

When the Carbon Savings value is 2460.06375[kg].

23h 9Ah <ID1> <ID2> 09h 00h 9Ch 90h 00h 00h 06h F9h 00h 00h

<CKS>

3.19 [ 050. REMOTE KEY CODE ]

Sends the key code for remote control.

Command

02h 0Fh 00h 00h 02h <DATA01> <DATA02> <CKS>

Data part

132

133

138

163

Key code

DATA01

DATA02

Item

4Bh

4Ch

4Fh

51h

84h

85h

8Ah

A3h

0Ah

0Bh

0Ch

0Dh

0Fh

10h

13h

29h

DATA01

02h

03h

05h

06h

07h

08h

09h

Description

Key code (WORD type)

For the combinations of key codes, see Table "Key code list".

00h

DATA02

00h

POWER ON

POWER OFF

AUTO

DOWN

RIGHT

LEFT

ENTER

EXIT

HELP

MAGNIFY UP

MAGNIFY DOWN

MUTE

PICTURE

COMPUTER1

COMPUTER2

VIDEO1

S-VIDEO1

VOLUME UP

VOLUME DOWN

FREEZE

ASPECT

Key name

Key code

215

238

DATA01

D7h

EEh

DATA02

00h

4 Command example

The following command sends the key code "AUTO".

SOURCE

LAMP MODE/ECO

Key name

02h 0Fh 00h 00h 02h 05h 00h 18h

Response

4 When the command succeeds

22h 0Fh <ID1> <ID2> 01h <DATA01> <CKS>

Data part

DATA01

Item

4 When the command fails

Description

Execution result

00h

FFh

Ended successfully.

Ended with an error.

A2h 0Fh <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.20 [ 053. LENS CONTROL ]

Adjusts the lens position.

Command

02h 18h 00h 00h 02h <DATA01> <DATA02> <CKS>

Data part

Item Description

DATA01

DATA02

Target

00h

01h

02h

03h

Content

00h

01h

02h

03h

7Fh

81h

FDh

FEh

FFh

Zoom

Focus

Lens Shift (H)

Lens Shift (V)

Stop

Drives for 1 second in the direction of plus

Drives for 0.5 second in the direction of plus

Drives for 0.25 second in the direction of plus

Drives in the direction of plus

Drives in the direction of minus

Drives for 0.25 second in the direction of minus

Drives for 0.5 second in the direction of minus

Drives for 1 second in the direction of minus

Information

After sending "7Fh" (Drives in the direction of plus) or "81h" (Drives in the direction of minus) in DATA02, you can stop driving lens by sending "00h".

Response

4 When the command succeeds

22h 18h <ID1> <ID2> 01h <DATA01> <CKS>

Data part

DATA01

Item

4 When the command fails

Description

Execution result

00h

FFh

Ended successfully.

Ended with an error.

A2h 18h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

Information

While the lens is being driven, you can control the lens position without a stop by issuing the same command.

3.21 [ 053-1. LENS CONTROL REQUEST ]

Gets adjusted values of the lens position.

Command

02h 1Ch 00h 00h 02h <DATA01> 00h <CKS>

Data part

DATA01

Item

Target

00h

01h

02h

03h

Zoom

Focus

Lens Shift (H)

Lens Shift (V)

Description

Response

4 When the command succeeds

22h 1Ch <ID1> <ID2> 08h <DATA01> 00h <DATA02> - <DATA07> <CKS>

Data part

DATA01

Item

DATA02

DATA03

DATA04

DATA05

DATA06

DATA07

4 When the command fails

Description

Target

00h

01h

02h

03h

Zoom

Focus

Lens Shift (H)

Lens Shift (V)

Upper limit of the adjustment range (low-order 8 bits)

Upper limit of the adjustment range (high-order 8 bits)

Lower limit of the adjustment range (low-order 8 bits)

Lower limit of the adjustment range (high-order 8 bits)

Current value (low-order 8 bits)

Current value (high-order 8 bits)

A2h 1Ch <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.22 [ 053-2. LENS CONTROL 2 ]

Adjusts the lens position.

Command

02h 1Dh 00h 00h 04h <DATA01> - <DATA04> <CKS>

Data part

DATA01

DATA02

Item Description

Target

00h

01h

02h

03h

Zoom

Focus

Lens Shift (H)

Lens Shift (V)

FFh

Adjustment mode

00h

Stop

Specify an absolute value

02h Specify a relative value

Adjustment value (low-order 8 bits)

Adjustment value (high-order 8 bits)

DATA03

DATA04

Information

If specifying “Stop” in DATA01, the Adjustment mode and Adjustment value are not referenced.

Response

4 When the command succeeds

22h 1Dh <ID1> <ID2> 02h <DATA01> <DATA02> <CKS>

Data part

DATA01

Item

DATA02

4 When the command fails

Description

Target

00h

01h

02h

03h

FFh

Adjustment mode

00h

02h

Zoom

Focus

Lens Shift (H)

Lens Shift (V)

Stop

Specify an absolute value

Specify a relative value

A2h 1Dh <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.23 [ 053-3. LENS MEMORY CONTROL ]

Controls the lens memory.

Information

See [ 053-4. REFERENCE LENS MEMORY CONTROL ] for controlling the reference lens memory.

Command

02h 1Eh 00h 00h 01h <DATA01> <CKS>

Data part

DATA01

Item

Operation

00h

01h

02h

STORE

MOVE

RESET

Description

Response

4 When the command succeeds

22h 1Eh <ID1> <ID2> 02h <DATA01> <DATA02> <CKS>

Data part

DATA01

DATA02

Item

4 When the command fails

Description

Operation

00h

01h

02h

Execution result

00h

FFh

STORE

MOVE

RESET

Ended successfully.

Ended with an error.

A2h 1Eh <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.24 [ 053-4. REFERENCE LENS MEMORY CONTROL ]

Controls the reference lens memory.

Information

・ See [ 053-3. LENS MEMORY CONTROL ] for controlling the lens memory.

・ This command controls the profile number specified in [053-10 LENS PROFILE SET ].

Command

02h 1Fh 00h 00h 01h <DATA01> <CKS>

Data part

DATA01

Item

Operation

00h

01h

02h

STORE

MOVE

RESET

Description

Response

4 When the command succeeds

22h 1Fh <ID1> <ID2> 02h <DATA01> <DATA02> <CKS>

Data part

DATA01

DATA02

Item

4 When the command fails

Description

Operation

00h

01h

02h

Execution result

00h

FFh

STORE

MOVE

RESET

Ended successfully.

Ended with an error.

A2h 1Fh <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.25 [ 053-5. LENS MEMORY OPTION REQUEST ]

Gets the value set for the lens memory.

Command

02h 20h 00h 00h 01h <DATA01> <CKS>

Data part

Item

DATA01 Target

00h

01h

Response

4 When the command succeeds

Description

LOAD BY SIGNAL

FORCED MUTE

22h 20h <ID1> <ID2> 02h <DATA01> <DATA02> <CKS>

Data part

Item

DATA01

DATA02

4 When the command fails

Target

00h

01h

Setting value

00h

01h

Description

LOAD BY SIGNAL

FORCED MUTE

OFF

A2h 20h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.26 [ 053-6. LENS MEMORY OPTION SET ]

Sets the lens memory.

Command

02h 21h 00h 00h 02h <DATA01> <DATA02> <CKS>

Data part

DATA01

Item

DATA02

Target

00h

01h

Setting value

00h

01h

Description

LOAD BY SIGNAL

FORCED MUTE

OFF

Response

4 When the command succeeds

22h 21h <ID1> <ID2> 02h <DATA01> <DATA02> <CKS>

Data part

DATA01

DATA02

Item

4 When the command fails

Description

Target

00h

01h

Execution result

00h

01h

LOAD BY SIGNAL

FORCED MUTE

Ended successfully.

Ended with an error.

A2h 21h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.27 [ 053-7. LENS INFORMATION REQUEST ]

Gets information about the lens of the projector.

Command

02h 22h 00h 00h 01h 00h 25h

Response

4 When the command succeeds

22h 22h <ID1> <ID2> 02h 00h <DATA01> <CKS>

Data part

Item

DATA01 Target

Bit0

Bit1

Bit2

Bit3

Lens memory

0 Stop

During operation 1

Zoom

0 Stop

During operation 1

Focus

0 Stop

1 During operation

Lens Shift (H)

Stop

During operation

4 When the command fails

Description

Bit4

Bit5

Bit6

Bit7

Lens Shift (V)

0 Stop

1 During operation

Reserved for the system

A2h 22h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.28 [ 053-10. LENS PROFILE SET ]

Selects the profile number of the reference lens memory.

Command

02h 27h 00h 00h 01h <DATA01> <CKS>

Data part

Item

DATA01 Profile number

00h

01h

Response

4 When the command succeeds

Profile 1

Profile 2

Description

22h 27h <ID1> <ID2> 02h <DATA01> <DATA02> <CKS>

Data part

DATA01

DATA02

Item

4 When the command fails

Description

Profile number

00h

01h

Execution result

00h

01h

Profile 1

Profile 2

Ended successfully.

Ended with an error.

A2h 27h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.29 [ 053-11. LENS PROFILE REQUEST ]

Gets the selected profile number of the reference lens memory.

Command

02h 28h 00h 00h 00h 2Ah

Response

4 When the command succeeds

22h 28h <ID1> <ID2> 02h <DATA01> <DATA02> <CKS>

Data part

Item

DATA01

DATA02

4 When the command fails

Profile number

00h

01h

Profile 1

Profile 2

Reserved for the system

Description

A2h 28h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.30 [ 060-1. GAIN PARAMETER REQUEST 3 ]

Gets adjusted values of the picture, volume, and so on.

Command

03h 05h 00h 00h 03h <DATA01> 00h 00h <CKS>

Data part

DATA01

Item Description

Adjusted value name

00h

01h

02h

03h

PICTURE / BRIGHTNESS

PICTURE / CONTRAST

PICTURE / COLOR

PICTURE / HUE

04h

05h

96h

PICTURE / SHARPNESS

VOLUME

LAMP ADJUST / LIGHT ADJUST

4 Command example

The following command gets the adjusted value of the picture (brightness).

03h 05h 00h 00h 03h 00h 00h 00h 0Bh

Response

4 When the command succeeds

23h 05h <ID1> <ID2> 10h <DATA01> - <DATA16> <CKS>

Data part

DATA01

Item

DATA02

DATA03

DATA04

DATA05

DATA06

DATA07

DATA08

DATA09

DATA10

DATA11

DATA12

DATA13

DATA14

DATA15

DATA16

4 When the command fails

Description

Adjusted value status

00h Display not possible

01h

02h

FFh

Adjustment not possible

Adjustment possible

The specified gain does not exist.

Upper limit of the adjustment range (low-order 8 bits)

Upper limit of the adjustment range (high-order 8 bits)

Lower limit of the adjustment range (low-order 8 bits)

Lower limit of the adjustment range (high-order 8 bits)

Default value (low-order 8 bits)

Default value (high-order 8 bits)

Current value (low-order 8 bits)

Current value (high-order 8 bits)

Wide adjustment width (low-order 8 bits)

Wide adjustment width (high-order 8 bits)

Narrow adjustment width (low-order 8 bits)

Narrow adjustment width (high-order 8 bits)

Whether the default value is valid or invalid

00h

01h

The default value is invalid.

The default value is valid.

Reserved for the system

A3h 05h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.31 [ 078-1. SETTING REQUEST ]

Gets information of the projector.

Command

00h 85h 00h 00h 01h 00h 86h

Response

4 When the command succeeds

20h 85h <ID1> <ID2> 20h <DATA01> - <DATA32> <CKS>

Data part

Item

DATA01 - 03

DATA04

DATA05

Description

Base model type

Sound function

00h

01h

Profile number

00h

Not available

Available

Not available

01h

02h

03h

Clock function

Sleep timer function

Clock function and Sleep timer function

Reserved for the system DATA06 - 32

Information

For the values of the base model types, see the Appendix "Supplementary Information by Command".

4 When the command fails

A0h 85h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.32 [ 078-2. RUNNING STATUS REQUEST ]

Gets the information about the operation status of the projector.

Command

00h 85h 00h 00h 01h 01h 87h

Response

4 When the command succeeds

20h 85h <ID1> <ID2> 10h <DATA01> - <DATA16> <CKS>

Data part

Item

DATA01 - 02

DATA03

Reserved for the system

Power status

00h Standby

DATA04

DATA05

DATA06

01h Power on

Cooling process

00h Not executed

01h During execution

Power On/Off process

00h Not executed

01h During execution

Operation status

00h

04h

Standby (Sleep)

Power on

05h

06h

Cooling

Standby (error)

DATA07 - 16 Reserved for the system

4 When the command fails

Description

A0h 85h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

FFh

－

Not supported

－

FFh

－

Not supported

－

FFh

－

Not supported

－

0Fh

10h

FFh

－

Standby (Power saving)

Network standby

Not supported

－

3.33 [ 078-3. INPUT STATUS REQUEST ]

Gets the information about the input signal status of the projector.

Command

00h 85h 00h 00h 01h 02h 88h

Response

4 When the command succeeds

20h 85h <ID1> <ID2> 10h <DATA01> - <DATA16> <CKS>

Data part

Item

DATA01

DATA02

DATA03

DATA04

Signal switch process

00h Not executed

01h During execution

Signal list number

00h –

C7h

Signal list number - 1

Selection signal type 1

01h 1

02h

03h

Selection signal type 2

01h

02h

03h

COMPUTER

VIDEO

S-VIDEO

04h

05h

07h

COMPONENT

Reserved for the system

VIEWER(1-5)

Description

FFh

－

Not supported

－

FFh Not supported

04h

05h

－

20h

21h

22h

23h

FFh

―

DVI-D

HDMI

DisplayPort

VIEWER(6-10)

Not Source Input

－

Item

DATA05

DATA06

DATA07 - 08

DATA09

Signal list type

00h Default

01h User

Test pattern display

00h

01h

Not displayed

Displayed

Reserved for the system

Content displayed

00h Video signal displayed

01h

02h

No signal

Viewer displayed

Reserved for the system

Description

FFh

－

Not supported

－

FFh

－

Not supported

－

03h

04h

FFh

Test pattern displayed

LAN displayed

Not supported

DATA10 - 16

Information

・ A value which is "1" smaller than a practical value will be returned as a signal list number. For finding out a practical number, add "1" to the returned value.

・ For information about the Selection signal type, see the Appendix "Supplementary Information by

Command".

4 When the command fails

A0h 85h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

4 Response example

When the signal list number is10.

20h 85h <ID1> <ID2> 10h <DATA01> 09h <DATA03> - <DATA16> <CKS>

3.34 [ 078-4. MUTE STATUS REQUEST ]

Gets the mute status of the projector.

Command

00h 85h 00h 00h 01h 03h 89h

Response

4 When the command succeeds

20h 85h <ID1> <ID2> 10h <DATA01> - <DATA16> <CKS>

Data part

DATA01

Item

DATA02

DATA03

Picture mute

00h

01h

FFh

Sound mute

00h

01h

FFh

Onscreen mute

00h

01h

FFh

Off

Not supported

Off

Not supported

Off

Not supported

Description

DATA04

DATA05

Item

DATA06 - 16

4 When the command fails

Forced onscreen mute

00h

01h

FFh

Off

Not supported

Description

Onscreen display

00h

01h

FFh

Not displayed

Displayed

Not supported

Reserved for the system

A0h 85h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.35 [ 078-5. MODEL NAME REQUEST ]

Gets the model name of the projector.

Command

00h 85h 00h 00h 01h 04h 8Ah

Response

4 When the command succeeds

20h 85h <ID1> <ID2> 20h <DATA01> - <DATA32> <CKS>

Data part

Item

DATA01 - 32

4 When the command fails

Description

Model name (NUL: termination character string)

A0h 85h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.36 [ 078-6. COVER STATUS REQUEST ]

Gets the status of the mirror cover or lens cover.

Command

00h 85h 00h 00h 01h 05h 8Bh

Response

4 When the command succeeds

20h 85h <ID1> <ID2> 01h <DATA01> <CKS>

Data part

Item

DATA01

4 When the command fails

Status

00h

01h

Description

Normal (cover opened)

Cover closed

A0h 85h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.37 [ 079. FREEZE CONTROL ]

Controls whether to turn the freeze function on or off.

Command

01h 98h 00h 00h 01h <DATA01> <CKS>

Data part

Item

DATA01 Operation

01h

02h

Response

4 When the command succeeds

Description

Turns the freeze function on.

Turns the freeze function off.

21h 98h <ID1> <ID2> 01h <DATA01> <CKS>

Data part

DATA01

Item

4 When the command fails

Description

Execution result

00h

01h

Ended successfully.

Ended with an error.

A1h 98h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.38 [ 084. INFORMATION STRING REQUEST ]

Gets the information strings (English) displayed on the projector.

Command

00h D0h 00h 00h 03h 00h <DATA01> 01h <CKS>

Data part

DATA01

Item

Response

4 When the command succeeds

Description

Information type

03h

04h

Horizontal synchronous frequency

Vertical synchronous frequency

20h D0h <ID1> <ID2> LEN <DATA01> 01h <DATA02> - <DATA??> <CKS>

Data part

DATA01

Item

DATA02

DATA03 - ??

4 When the command fails

Description

Information type

03h

04h

Horizontal synchronous frequency

Vertical synchronous frequency

Label/information string length (excluding NUL characters)

Label/information strings (NUL: termination character string)

A0h D0h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.39 [ 097-8. ECO MODE REQUEST ]

Gets the value set for the eco mode.

Information

Depending on the projector, the value for the "Light mode" or "Lamp mode" will be returned.

Command

03h B0h 00h 00h 01h 07h BBh

Response

4 When the command succeeds

23h B0h <ID1> <ID2> 02h 07h <DATA01> <CKS>

Data part

Item Description

DATA01 Value set for the eco mode

Information

For information about the values set for the eco mode, see the Appendix "Supplementary Information by

Command".

4 When the command fails

A3h B0h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.40 [ 097-45. LAN PROJECTOR NAME REQUEST ]

Gets the projector name.

Command

03h B0h 00h 00h 01h 2Ch E0h

Response

4 When the command succeeds

23h B0h <ID1> <ID2> 12h 2Ch <DATA01> - <DATA17> <CKS>

Data part

Item

DATA01 - 17

4 When the command fails

Description

Projector name (NUL: termination character string)

A3h B0h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.41 [ 097-155. LAN MAC ADDRESS STATUS REQUEST2 ]

Gets the MAC address of the projector.

Command

03h B0h 00h 00h 02h 9Ah 00h 4Fh

Response

4 When the command succeeds

23h B0h <ID1> <ID2> 08h 9Ah 00h <DATA01> - <DATA06> <CKS>

Data part

Item

DATA01 - 06

4 When the command fails

MAC address

Description

A3h B0h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

4 Response example

When the MAC address of the projector is "01h-23h-45h-67h-89h-ABh", the following response is returned.

23h B0h <ID1> <ID2> 08h 9Ah 00h 01h 23h 45h 67h 89h ABh <CKS>

3.42 [ 097-198. PIP/PICTURE BY PICTURE REQUEST ]

Gets the value set for the picture in picture and picture by picture.

Command

03h B0h 00h 00h 02h C5h <DATA01> <CKS>

Data part

DATA01

Item

Target

00h

01h

02h

Description

MODE

START POSITION

SUB INPUT

Response

4 When the command succeeds

23h B0h <ID1> <ID2> 03h C5h <DATA01> <DATA02> <CKS>

Data part

DATA01

DATA02

Item Description

Target

00h MODE

01h

02h

START POSITION

SUB INPUT

Setting value (when DATA01 is 00h "MODE")

00h

01h

PIP

PICTURE BY PICTURE

Setting value (when DATA01 is 01h "START POSITION")

00h

01h

TOP-LEFT

TOP-RIGHT

02h

03h

BOTTOM-LEFT

BOTTOM-RIGHT

Sub input setting value (when DATA01 is 02h "SUB INPUT")

Information

For the values of the Sub input setting value, see the Appendix "Supplementary Information by Command".

4 When the command fails

A3h B0h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.43 [ 097-243-1. EDGE BLENDING MODE REQUEST ]

Gets the value set for the edge blending.

Command

03h B0h 00h 00h 02h DFh 00h 94h

Response

4 When the command succeeds

23h B0h <ID1> <ID2> 03h DFh 00h <DATA01> <CKS>

Data part

Item

DATA01

4 When the command fails

Setting value

00h

01h

OFF

Description

A3h B0h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.44 [ 098-8. ECO MODE SET ]

Sets the eco mode.

Information

Depending on the projector, the "Light mode" or "Lamp mode" will be set.

Command

03h B1h 00h 00h 02h 07h <DATA01> <CKS>

Item Description

DATA01 Value set for the eco mode

Information

For information about the values set for the eco mode, see the Appendix "Supplementary Information by

Command".

Response

4 When the command succeeds

23h B1h <ID1> <ID2> 02h 07h <DATA01> <CKS>

Data part

DATA01

Item

4 When the command fails

Description

Execution result

00h

01h

Ended successfully.

Ended with an error.

A3h B1h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.45 [ 098-45. LAN PROJECTOR NAME SET ]

Sets the projector name.

Command

03h B1h 00h 00h 12h 2Ch <DATA01> - <DATA16> 00h <CKS>

Data part

Item

DATA01 - 16

Response

Projector name (up to 16 bytes)

4 When the command succeeds

Description

23h B1h <ID1> <ID2> 02h 2Ch <DATA01> <CKS>

Data part

DATA01

Item

4 When the command fails

Description

Execution result

00h

01h

Ended successfully.

Ended with an error.

A3h B1h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.46 [ 098-198. PIP/PICTURE BY PICTURE SET ]

Sets the picture in picture or picture by picture.

Command

03h B1h 00h 00h 03h C5h <DATA01> <DATA02> <CKS>

Data part

DATA01

DATA02

Item Description

Target

00h

01h

MODE

START POSITION

02h SUB INPUT

Setting value (when DATA01 is 00h "Mode")

00h

01h

PIP

PICTURE BY PICTURE

Setting value (when DATA01 is 01h "START POSITION")

00h

01h

TOP-LEFT

TOP-RIGHT

02h

03h

BOTTOM-LEFT

BOTTOM-RIGHT

Sub input setting value (when DATA01 is 02h "SUB INPUT")

Information

For the values of the Sub input setting value, see the Appendix "Supplementary Information by Command".

Response

4 When the command succeeds

23h B1h <ID1> <ID2> 03h C5h <DATA01> <DATA02> <CKS>

Data part

DATA01

DATA02

Item

4 When the command fails

Description

Target

00h

01h

02h

Execution result

00h

01h

MODE

START POSITION

SUB INPUT

Ended successfully.

Ended with an error.

A3h B1h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.47 [ 098-243-1. EDGE BLENDING MODE SET ]

Sets the edge blending.

Command

03h B1h 00h 00h 03h DFh 00h <DATA01> <CKS>

Data part

Item

DATA01 Setting value

00h

01h

Response

4 When the command succeeds

00h

01h

Description

23h B1h <ID1> <ID2> 03h DFh 00h <DATA01> <CKS>

Data part

DATA01

Item

4 When the command fails

Description

Execution result

00h

01h

Ended successfully.

Ended with an error.

A3h B1h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.48 [ 305-1. BASE MODEL TYPE REQUEST ]

Gets the base model type of the projector.

Command

00h BFh 00h 00h 01h 00h C0h

Response

4 When the command succeeds

20h BFh <ID1> <ID2> 10h 00h <DATA01> - <DATA15> <CKS>

Data part

DATA01

DATA02

DATA03 - 11

DATA12

DATA13

DATA14

DATA15

Item

Base model type

Model name (NUL: termination character string)

Base model type

Reserved for the system

Description

Information

For the values of the base model types, see the Appendix "Supplementary Information by Command".

4 When the command fails

A0h BFh <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.49 [ 305-2. SERIAL NUMBER REQUEST ]

Gets the serial number of the projector.

Command

00h BFh 00h 00h 02h 01h 06h C8h

Response

4 When the command succeeds

20h BFh <ID1> <ID2> 12h 01h 06h <DATA01> - <DATA16> <CKS>

Data part

Item

DATA01 - 16

4 When the command fails

Description

Serial number (NUL: termination character string)

A0h BFh <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.50 [ 305-3. BASIC INFORMATION REQUEST ]

Gets the basic information about the operation status of the projector.

Command

00h BFh 00h 00h 01h 02h C2h

Response

4 When the command succeeds

20h BFh <ID1> <ID2> 10h 02h <DATA01> - <DATA15> <CKS>

Data part

Item

DATA01

DATA02

DATA03

Operation status

00h Standby (Sleep)

04h Power on

05h Cooling

Content displayed

00h

01h

02h

03h

Video signal displayed

No signal

Viewer displayed

Test pattern displayed

Selection signal type 1

01h 1

02h

03h

Description

06h

0Fh

10h

Standby (error)

Standby (Power saving)

Network standby

04h

05h

10h

－

LAN displayed

Test pattern (user) displayed

Signal being switched

－

04h

05h

－

DATA04

Item

DATA05

DATA06

DATA07

DATA08

DATA09

Description

Selection signal type 2

01h

02h

03h

04h

05h

07h

COMPUTER

VIDEO

S-VIDEO

COMPONENT

Reserved for the system

VIEWER(1-5)

20h

21h

22h

23h

FFh

―

DVI-D

HDMI

DisplayPort

VIEWER(6-10)

Not Source Input

－

Display signal type (effective only when DATA04 is 02h or 03h)

00h NTSC3.58 09h NTSC3.58 SQZ

01h

02h

NTSC4.43

PAL

0Ah

0Bh

COMPONENT(60Hz)

COMPONENT(50Hz)

03h

04h

05h

PAL60

SECAM

B/W60

0Ch

0Dh

0Eh

Unknown

NTSC

PAL-M

06h

07h

08h

B/W50

PALNM

NTSC3.58 LBX

0Fh

FFh

―

PAL-L

Not Video Input

－

Video mute

00h Off

Sound mute

00h Off

Onscreen mute

00h Off

Freeze status

00h Off

Reserved for the system

01h

DATA10 - 15

Information

For information about which parameters are supported, see the Appendix "Supplementary Information by

Command".

4 When the command fails

A0h BFh <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

3.51 [ 319-10. AUDIO SELECT SET ]

Sets the audio select.

Command

03h C9h 00h 00h 03h 09h <DATA01> <DATA02> <CKS>

Data part

Item

DATA01

DATA02

Description

Target

00h HDMI1

01h

02h

HDMI2

DisplayPort

Setting value

00h The terminal specified in

DATA01

01h BNC

03h

04h

05h

02h

－

ETHRENET or HDBaseT

USB-A

USB-B

COMPUTER

－

Response

4 When the command succeeds

23h C9h <ID1> <ID2> 03h 09h <DATA01> <DATA02> <CKS>

Data part

Item

DATA01 Target

00h HDMI1

01h

02h

HDMI2

DisplayPort

DATA02 Execution result

00h Ended successfully.

4 When the command fails

Description

03h

04h

05h

ETHRENET or HDBaseT

USB-A

USB-B

01h Ended with an error.

A3h C9h <ID1> <ID2> 02h <ERR1> <ERR2> <CKS>

Revision History

Revision

4.0

3.0

2.0

Date

December 11, 2015

June 16, 2015

May 29, 2015

August 22, 2014

Description

Corrected the supported command

[053-6]

Added the supported command

[030-15]

Updated the supported command

[060-1]

Added the supported commands

[030-12], [037], [037-6], [053], [053-1], [053-2], [053-3], [053-4], [053-5], [053-6], [053-7],

[053-10], [053-11], [078-1], [078-2], [078-3], [078-4], [078-5], [097-198], [097-243-1],

[098-8], [098-198], [098-243-1], [319-10]

Updated the supported command

[009]

First version 1.0

Projector Control Command

Reference Manual

Projector Control Command Reference Manual Appendixes

The Appendixes provide supplementary information about the control commands.

No.BDT140014

Revision History

Revision

8.0

7.0

6.0

5.0

4.0

Date Description

December 21, 2015 Added the supported models.

December 11, 2015 Added the supported models.

September 28, 2015 Added the supported models.

August 7, 2015

August 3, 2015

Added the supported models.

Corrected [3. Supported

Command List ] sheet.

(NP-U321H : "024. ONSCREEN

MUTE ON" command is not supported.)

Reference

4.0

3.0

Supported models

NP-M403X / NP-M363X / NP-M323X / NP-M283X / NP-M403W / NP-M363W /

NP-M323W / NP-M333XS / NP-M353WS / NP-M303WS /

NP-M403H / NP-M323H / NP-M353HS / NP-M323HS / NP-M303HS

NP-M402W / NP-M362W / NP-M402X / NP-M362X / NP-M322X / NP-M282X /

NP-M322W / NP-M352WS / NP-M302WS / NP-M332XS

NP-P502HL / NP-P502WL

NP-P502H / NP-P502W / NP-P452H / NP-P452W

NP-PA622U / NP-PA522U / NP-PA672W / NP-PA572W / NP-PA722X /

NP-PA622X / NP-PA621U / NP-PA521U / NP-PA671W / NP-PA571W /

NP-PA721X / NP-PA621X

NP-PH1202HL / PH1002HL

NP-PX651X / NP-PX581W

NP-PX602UL / PX602WL

NP-PX803UL

NP-U321H

NP-UM301X / NP-UM301W / NP-UM361X / NP-UM351W / NP-UM352W

NP-V332X / NP-V332W / NP-V302X / NP-V302W / NP-V302H

NP-M403X / NP-M363X / NP-M323X / NP-M283X / NP-M403W / NP-M363W /

NP-M323W / NP-M333XS / NP-M353WS / NP-M303WS /

NP-M403H / NP-M323H / NP-M353HS / NP-M323HS / NP-M303HS

NP-M402W / NP-M362W / NP-M402X / NP-M362X / NP-M322X / NP-M282X /

NP-M322W / NP-M352WS / NP-M302WS / NP-M332XS

NP-P502HL / NP-P502WL

NP-PA622U / NP-PA522U / NP-PA672W / NP-PA572W / NP-PA722X /

NP-PA622X / NP-PA621U / NP-PA521U / NP-PA671W / NP-PA571W /

NP-PA721X / NP-PA621X

NP-PH1202HL / PH1002HL

NP-PX651X / NP-PX581W

NP-PX602UL / PX602WL

NP-PX803UL

NP-U321H

NP-UM301X / NP-UM301W / NP-UM361X / NP-UM351W / NP-UM352W

NP-V332X / NP-V332W / NP-V302X / NP-V302W / NP-V302H

NP-M403X / NP-M363X / NP-M323X / NP-M283X / NP-M403W / NP-M363W /

NP-M323W / NP-M333XS / NP-M353WS / NP-M303WS /

NP-M403H / NP-M323H / NP-M353HS / NP-M323HS / NP-M303HS

NP-M402W / NP-M362W / NP-M402X / NP-M362X / NP-M322X / NP-M282X /

NP-M322W / NP-M352WS / NP-M302WS / NP-M332XS

NP-P502HL / NP-P502WL

NP-PA622U / NP-PA522U / NP-PA672W / NP-PA572W / NP-PA722X /

NP-PA622X / NP-PA621U / NP-PA521U / NP-PA671W / NP-PA571W /

NP-PA721X / NP-PA621X

NP-PH1202HL / PH1002HL

NP-PX651X / NP-PX581W

NP-PX602UL / PX602WL

NP-U321H

NP-UM301X / NP-UM301W / NP-UM361X / NP-UM351W / NP-UM352W

NP-V332X / NP-V332W / NP-V302X / NP-V302W / NP-V302H

NP-M403X / NP-M363X / NP-M323X / NP-M283X / NP-M403W / NP-M363W /

NP-M323W / NP-M333XS / NP-M353WS / NP-M303WS /

NP-M403H / NP-M323H / NP-M353HS / NP-M323HS / NP-M303HS

NP-M402W / NP-M362W / NP-M402X / NP-M362X / NP-M322X / NP-M282X /

NP-M322W / NP-M352WS / NP-M302WS / NP-M332XS

NP-PA622U / NP-PA522U / NP-PA672W / NP-PA572W / NP-PA722X /

NP-PA622X / NP-PA621U / NP-PA521U / NP-PA671W / NP-PA571W /

NP-PA721X / NP-PA621X

NP-PH1202HL / PH1002HL

NP-PX651X / NP-PX581W

NP-PX602UL / PX602WL

NP-U321H

NP-UM301X / NP-UM301W / NP-UM361X / NP-UM351W / NP-UM352W

NP-V332X / NP-V332W / NP-V302X / NP-V302W / NP-V302H

NP-M403X / NP-M363X / NP-M323X / NP-M283X / NP-M403W / NP-M363W /

NP-M323W / NP-M333XS / NP-M353WS / NP-M303WS /

NP-M403H / NP-M323H

NP-M402W / NP-M362W / NP-M402X / NP-M362X / NP-M322X / NP-M282X /

NP-M322W / NP-M352WS / NP-M302WS / NP-M332XS

NP-PA622U / NP-PA522U / NP-PA672W / NP-PA572W / NP-PA722X /

NP-PA622X / NP-PA621U / NP-PA521U / NP-PA671W / NP-PA571W /

NP-PA721X / NP-PA621X

NP-PH1202HL / PH1002HL

NP-PX651X / NP-PX581W

NP-PX602UL / PX602WL

NP-U321H

NP-UM301X / NP-UM301W / NP-UM361X / NP-UM351W / NP-UM352W

NP-V332X / NP-V332W / NP-V302X / NP-V302W / NP-V302H

3.0

June 16, 2015 Added the supported command.

3.0

Same as Revision 2.0.

2.0

1.0

May 29, 2015

Changed the supported models.

Added the supported commands.

August 22, 2014 First version

2.0

1.0

NP-M402W / NP-M362W / NP-M402X / NP-M362X / NP-M322X / NP-M282X /

NP-M322W / NP-M352WS / NP-M302WS / NP-M332XS

NP-PA622U / NP-PA522U / NP-PA672W / NP-PA572W / NP-PA722X /

NP-PA622X / NP-PA621U / NP-PA521U / NP-PA671W / NP-PA571W /

NP-PA721X / NP-PA621X

NP-PH1202HL / PH1002HL

NP-PX651X / NP-PX581W

NP-PX602UL / PX602WL

NP-U321H

NP-UM301X / NP-UM301W / NP-UM361X / NP-UM351W / NP-UM352W

NP4100 / NP4100W

NP-M420X / NP-M420XV / NP-M350X / NP-M300X / NP-M260X / NP-M230X /

NP-M300W / NP-M260W / NP-M350XS / NP-M300XS / NP-M260XS /

NP-M300WS / NP-M260WS

NP-M402W / NP-M362W / NP-M402X / NP-M362X / NP-M322X / NP-M282X /

NP-M322W / NP-M352WS / NP-M302WS / NP-M332XS

NP-M361X / NP-M311X / NP-M271X / NP-M311W / NP-M271W

NP-ME360X / NP-ME310X / NP-ME270X

NP-P501X / NP-P451X / NP-P451W / NP-P401W / NP-PE501X

NP-P420X / NP-P350X / NP-P350W

NP-PE401H

NP-PA622U / NP-PA522U / NP-PA672W / NP-PA572W / NP-PA722X /

NP-PA622X / NP-PA621U / NP-PA521U / NP-PA671W / NP-PA571W /

NP-PA721X / NP-PA621X

NP-PA600X / NP-PA500X / NP-PA550W / NP-PA500U

NP-PH1400U

NP-PH1000U

NP-PX750U / NP-PX700W / NP-PX800X

NP-PX620X / NP-PX550W

NP-U300X / NP-U250X / NP-U310W / NP-U260W

NP-UM330X / NP-UM280X / NP-UM330W / NP-UM280W

NP-V311W / NP-V281W / NP-V311X

NP-V300X / NP-V260X / NP-V300W / NP-V260W / NP-V230X / NP-V260 /

NP-V230 / NP-V260R

NP-VE281X / NP-VE280X / NP-VE281 / NP-VE280

Contents

1. Connecting an External Device

2. Standby Mode setting for receiving commands

3. Supported Command List

4. Supplementary Information by Command

Input terminal

[018. INPUT SW CHANGE]

Aspect

[030-12. ASPECT ADJUST]

Eco mode

[097-8. ECO MODE REQUEST]

[098-8. ECO MODE SET]

Base model type

[078-1. SETTING REQUEST]

[305-1. BASE MODEL TYPE REQUEST]

Selection signal type

[078-3. INPUT STATUS REQUEST]

[305-3. BASIC INFORMATION REQUEST]

Sub input

[097-198. PIP/PICTURE BY PICTURE REQUEST]

[098-198. PIP/PICTURE BY PICTURE SET]

1. Connecting an External Device

○ : Supported

－ : Not supported

■ Projector

Model name

NP-M403X / NP-M363X / NP-M323X / NP-M283X / NP-M403W / NP-

M363W / NP-M323W / NP-M333XS / NP-M353WS / NP-M303WS /

NP-M403H / NP-M323H / NP-M353HS / NP-M323HS / NP-M303HS

NP-M402W / NP-M362W / NP-M402X / NP-M362X / NP-M322X /

NP-M282X / NP-M322W / NP-M352WS / NP-M302WS / NP-M332XS

NP-P502HL / NP-P502WL

NP-P502H / NP-P502W / NP-P452H / NP-P452W

NP-PA622U / NP-PA522U / NP-PA672W / NP-PA572W /

NP-PA722X / NP-PA622X

NP-PA621U / NP-PA521U / NP-PA671W / NP-PA571W /

NP-PA721X / NP-PA621X

NP-PH1202HL / PH1002HL

NP-PX803UL

NP-PX651X / NP-PX581W

NP-PX602UL / PX602WL

NP-U321H

NP-UM301X / NP-UM301W / NP-UM361X / NP-UM351W

NP-UM352W

NP-V332X / NP-V332W / NP-V302X / NP-V302W / NP-V302H

4800bps 9600bps

Serial port

19200bps 38400bps 115200bps

LAN port Wireless LAN unit

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

2. Standby Mode setting for receiving commands

The Standby Mode setting that can receive commands is different depending on the model.

Please see the table below.

Target command: "015. POWER ON"

■ Projector

Setting of the Standby Mode

When connected using a serial cable When connected using via a wired LAN Model name

NP-M403X / NP-M363X / NP-M323X / NP-M283X / NP-M403W / NP-

M363W / NP-M323W / NP-M333XS / NP-M353WS / NP-M303WS /

NP-M403H / NP-M323H / NP-M353HS / NP-M323HS / NP-M303HS

NP-M402W / NP-M362W / NP-M402X / NP-M362X / NP-M322X /

NP-M282X / NP-M322W / NP-M352WS / NP-M302WS / NP-M332XS

NP-P502HL / NP-P502WL

NP-P502H / NP-P502W / NP-P452H / NP-P452W

NP-PA622U / NP-PA522U / NP-PA672W / NP-PA572W /

NP-PA722X / NP-PA622X

NP-PA621U / NP-PA521U / NP-PA671W / NP-PA571W /

NP-PA721X / NP-PA621X

NP-PH1202HL / PH1002HL

NP-PX803UL

NP-PX651X / NP-PX581W

NP-PX602UL / PX602WL

NP-U321H

NP-UM301X / NP-UM301W / NP-UM361X / NP-UM351W

NP-UM352W

NP-V332X / NP-V332W / NP-V302X / NP-V302W / NP-V302H

NORMAL, NETWORK STANDBY

NORMAL, HTBaseT STANDBY

NORMAL, NETWORK STANDBY

NETWORK STANDBY

HTBaseT STANDBY

NETWORK STANDBY

3. Supported Command List

○ : Supported

－ : Not supported

■ Projector

Command

009. ERROR STATUS REQUEST

015. POWER ON

016. POWER OFF

018. INPUT SW CHANGE

020. PICTURE MUTE ON

021. PICTURE MUTE OFF

022. SOUND MUTE ON

023. SOUND MUTE OFF

024. ONSCREEN MUTE ON

025. ONSCREEN MUTE OFF

030-1. PICTURE ADJUST

030-2. VOLUME ADJUST

030-12. ASPECT ADJUST

030-15. OTHER ADJUST

037. INFORMATION REQUEST

037-3. FILTER USAGE INFORMATION REQUEST

037-4. LAMP INFORMATION REQUEST 3

037-6. CARBON SAVINGS INFORMATION REQUEST

050. REMOTE KEY CODE

053. LENS CONTROL

053-1. LENS CONTROL REQUEST

053-2. LENS CONTROL 2

053-3. LENS MEMORY CONTROL

053-4. REFERENCE LENS MEMORY CONTROL

053-5. LENS MEMORY OPTION REQUEST

053-6. LENS MEMORY OPTION SET

053-7. LENS INFORMATION REQUEST

053-10. LENS PROFILE SET

053-11. LENS PROFILE REQUEST

060-1. GAIN PARAMETER REQUEST 3

078-1. SETTING REQUEST

078-2. RUNNING STATUS REQUEST

078-3. INPUT STATUS REQUEST

078-4. MUTE STATUS REQUEST

078-5. MODEL NAME REQUEST

078-6. COVER STATUS REQUEST

079. FREEZE CONTROL

084. INFORMATION STRING REQUEST

097-8. ECO MODE REQUEST

097-45. LAN PROJECTOR NAME REQUEST

097-155. LAN MAC ADDRESS STATUS REQUEST2

097-198. PIP/PICTURE BY PICTURE REQUEST

097-243-1. EDGE BLENDING MODE REQUEST

098-8. ECO MODE SET

098-45. LAN PROJECTOR NAME SET

098-198. PIP/PICTURE BY PICTURE SET

098-243-1. EDGE BLENDING MODE SET

305-1. BASE MODEL TYPE REQUEST

305-2. SERIAL NUMBER REQUEST

305-3. BASIC INFORMATION REQUEST

319-10. AUDIO SELECT SET

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

NP-M403X

NP-M363X

NP-M323X

NP-M283X

NP-M403W

NP-M363W

NP-M323W

NP-M333XS

NP-M353WS

NP-M303WS

NP-M403H

NP-M323H

NP-M353HS

NP-M323HS

NP-M303HS

NP-M402W

NP-M362W

NP-M402X

NP-M362X

NP-M322X

NP-M282X

NP-M322W

NP-M352WS

NP-M302WS

NP-M332XS

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

NP-P502HL

NP-P502WL

NP-P502H

NP-P502W

NP-P452H

NP-P452W

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

NP-PA622U

NP-PA522U

NP-PA672W

NP-PA572W

NP-PA722X

NP-PA622X

NP-PA621U

NP-PA521U

NP-PA671W

NP-PA571W

NP-PA721X

NP-PA621X

NP-PH1202HL

NP-PH1002HL

NP-PX803UL NP-PX651X

NP-PX581W

NP-PX602UL

NP-PX602WL

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

NP-U321H NP-UM301X

NP-UM301W

NP-UM361X

NP-UM351W

NP-V332X

NP-V332W

NP-V302X

NP-V302W

NP-V302H

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

○

－

4. Supplementary Information by Command

018. INPUT SW CHANGE

■Input terminal

Model name

NP-M403X / NP-M363X / NP-M323X / NP-M283X / NP-M403W / NP-

M363W / NP-M323W / NP-M333XS / NP-M353WS / NP-M303WS /

NP-M403H / NP-M323H / NP-M353HS / NP-M323HS / NP-M303HS

NP-M402W / NP-M362W / NP-M402X / NP-M362X / NP-M322X /

NP-M282X / NP-M322W / NP-M352WS / NP-M302WS / NP-M332XS

NP-P502HL / NP-P502WL

NP-P502H / NP-P502W / NP-P452H / NP-P452W

NP-PA622U / NP-PA522U / NP-PA672W / NP-PA572W /

NP-PA722X / NP-PA622X

NP-PA621U / NP-PA521U / NP-PA671W / NP-PA571W /

NP-PA721X / NP-PA621X

NP-PH1202HL / NP-PH1002HL

NP-PX803UL

NP-PX651X / NP-PX581W

NP-PX602UL / NP-PX602WL

NP-U321H

NP-UM352W

NP-UM301X / NP-UM301W / NP-UM361X / NP-UM351W

NP-V332X / NP-V332W / NP-V302X / NP-V302W / NP-V302H

COMPUTER COMPUTER2 COMPUTER3

01h

－

02h

－

9Ch

－

BNC

－

02h

02ｈ

－

02ｈ

－

VIDEO

06h

－

06h

－

06h

BNC(CV)

－

06h

06ｈ

－

06ｈ

－

S-VIDEO

－

BNC(Y/C) Component

Input terminal

HDMI

－－ A1h

－

0Bh

－

0Bh

－

0Bh

－

10h

－

A1h

HDMI2

A2h

－

A2h

－

DisplayPort

－

A6h

－

A6h

－

SLOT

－

ABh

－

ABh

－

USB-A

1Fh

－

1Fh

－

1Fh

－

LAN

20h

－

20h

－

ETHERNET HDBaseT

－－

－

20h

－

BFh

20h

－

20h

－

USB-B

22h

－

22h

－

APPS

－

23h

－

23h

－

4. Supplementary Information by Command

030-12. ASPECT ADJUST

■Aspect

Model name

00h 01h 02h

NP-M403X / NP-M363X / NP-M323X / NP-M283X / NP-M403W / NP-

M363W / NP-M323W / NP-M333XS / NP-M353WS / NP-M303WS /

NP-M403H / NP-M323H / NP-M353HS / NP-M323HS / NP-M303HS

NP-M402W / NP-M362W / NP-M402X / NP-M362X / NP-M322X /

NP-M282X / NP-M322W / NP-M352WS / NP-M302WS / NP-M332XS

NP-P502HL / NP-P502WL

NP-P502H / NP-P502W / NP-P452H / NP-P452W

NP-PA622U / NP-PA522U / NP-PA672W / NP-PA572W / NP-PA722X /

NP-PA622X / NP-PA621U / NP-PA521U / NP-PA671W / NP-PA571W /

NP-PA721X / NP-PA621X

NP-PH1202HL / NP-PH1002HL

NP-PX803UL

NP-PX651X / NP-PX581W

NP-PX602UL / NP-PX602WL

NP-U321H

NP-UM301X / NP-UM361X

NP-UM301W / NP-UM351W / NP-UM352W

NP-V332X / NP-V332W / NP-V302X / NP-V302W / NP-V302H

AUTO

WIDE ZOOM

－

WIDE ZOOM

－

CHINEMA

16:9

4:3 (WINDOWS) LETTER BOX WIDE SCREEN

4:3 － 16:9

4:3 (WINDOWS) LETTER BOX WIDE SCREEN

AUTO － 16:9

16:9

03h

NATIVE

－

1.85:1

－

NATIVE

04h

4:3

－

2.35:1

－

4:3

05h

15:9

－

Auto

－

15:9

DATA01

06h

16:10

ZOOM FULL

ZOOM

16:10

FULL

07h

LETTER BOX

－

LETTERBOX

－

08h

－

5:4

－

5:4

－

0Bh

－

5:4

－

0Ch

－

16:10

－

0Dh

－

15:9

－

15:9

－

0Eh

－

NATIVE

Native

NATIVE

－

0Fh

－

AUTO

Auto

AUTO

－

4. Supplementary Information by Command

097-8. ECO MODE REQUEST

098-8. ECO MODE SET

■Eco mode

Model name

00h

NP-M403X / NP-M363X / NP-M323X / NP-M283X / NP-M403W / NP-

M363W / NP-M323W / NP-M333XS / NP-M353WS / NP-M303WS /

NP-M403H / NP-M323H / NP-M353HS / NP-M323HS / NP-M303HS

NP-M402W / NP-M362W / NP-M402X / NP-M362X / NP-M322X /

NP-M282X / NP-M322W / NP-M352WS / NP-M302WS / NP-M332XS

NP-P502HL / NP-P502WL

NP-P502H / NP-P502W / NP-P452H / NP-P452W

NP-PA622U / NP-PA522U / NP-PA672W / NP-PA572W / NP-PA722X /

NP-PA622X / NP-PA621U / NP-PA521U / NP-PA671W / NP-PA571W /

NP-PA721X / NP-PA621X

NP-PH1202HL / PH1002HL

NP-PX803UL

NP-PX651X / NP-PX581W

NP-PX602UL / PX602WL

NP-U321H

NP-UM301X / NP-UM301W / NP-UM361X / NP-UM351W

NP-UM352W

NP-V332X / NP-V332W / NP-V302X / NP-V302W / NP-V302H

OFF

NORMAL

OFF

01h

AUTO ECO

ECO1

AUTO ECO

－

ECO

－

ECO

AUTO ECO

ECO

DATA01

02h

NORMAL

ECO2

NORMAL

－

ECO1

－

ECO1

－

NORMAL

－

03h

ECO

－

ECO

－

ECO2

－

ECO2

－

ECO

－

04h

－

LONG LIFE

－

NP-M402X

NP-M403H

NP-M403W

NP-M403X

NP-P452H

NP-P452W

NP-P502H

NP-P502HL

NP-P502W

NP-P502WL

NP-PA521U

NP-PA522U

NP-PA571W

NP-PA572W

NP-PA621U

NP-PA621X

NP-PA622U

NP-PA622X

NP-PA671W

NP-PA672W

NP-PA721X

NP-PA722X

NP-PH1002HL

NP-PH1202HL

NP-PX581W

NP-PX602UL

NP-PX602WL

NP-PX651X

NP-PX803UL

NP-U321H

NP-UM301W

NP-UM301X

NP-UM351W

NP-UM352W

NP-UM361X

NP-V302H

NP-V302W

NP-V302X

NP-V332W

NP-V332X

NP-M282X

NP-M283X

NP-M302WS

NP-M303HS

NP-M303WS

NP-M322H

NP-M322W

NP-M322X

NP-M323H

NP-M323HS

NP-M323W

NP-M323X

NP-M332XS

NP-M333XS

NP-M352WS

NP-M353HS

NP-M353WS

NP-M362W

NP-M362X

NP-M363W

NP-M363X

NP-M402H

NP-M402W

4. Supplementary Information by Command

078-1. SETTING REQUEST

305-1. BASE MODEL TYPE REQUEST

■Base model type

Model name

078-1. SETTING REQUEST

DATA01 DATA02

305-1. BASE MODEL TYPE REQUEST

DATA01

FFh

DATA02

22h

22H

22h

22H

22h

22H

22h

21h

26h

27h

25h

27h

2Ch

28h

20h

2Ah

21h

22H

22h

22H

22h

21h

22h

22H

DATA12

02h

07h

08h

02H

08h

05h

01h

05h

01h

00h

04h

03h

09h

04H

09h

01h

06h

02h

0Bh

03H

06h

00h

05h

02h

04h

01h

00h

01h

00h

01h

00h

02h

00h

03h

04h

01h

04h

03h

02h

01h

00h

01h

03h

00h

05h

00H

00h

01H

01h

00h

0Ah

04h

00h

02H

03H

DATA03

DATA13

12h

10h

12h

10h

11H

12h

10h

12h

11h

10h

12h

10h

11H

12h

11h

10h

12h

11H

12h

11h

10h

11h

10h

11h

10h

11h

10h

11h

10h

11h

10h

14H

13h

14H

13h

10h

12h

14H

4. Supplementary Information by Command

078-3. INPUT STATUS REQUEST

305-3. BASIC INFORMATION REQUEST

■Selection signal type

Model name

DATA03

DATA04

NP-M403X / NP-M363X / NP-M323X / NP-M283X / NP-M403W / NP-

M363W / NP-M323W / NP-M333XS / NP-M353WS / NP-M303WS /

NP-M403H / NP-M323H / NP-M353HS / NP-M323HS / NP-M303HS

NP-M402W / NP-M362W / NP-M402X / NP-M362X / NP-M322X /

NP-M282X / NP-M322W / NP-M352WS / NP-M302WS / NP-M332XS

NP-P502HL / NP-P502WL

NP-P502H / NP-P502W / NP-P452H / NP-P452W

NP-PA622U / NP-PA522U / NP-PA672W / NP-PA572W /

NP-PA722X / NP-PA622X

NP-PA621U / NP-PA521U / NP-PA671W / NP-PA571W /

NP-PA721X / NP-PA621X

NP-PH1202HL / NP-PH1002HL

NP-PX803UL

NP-PX651X / NP-PX581W

NP-PX602UL / NP-PX602WL

NP-U321H

NP-UM352W

NP-UM301X / NP-UM301W / NP-UM361X / NP-UM351W

NP-V332X / NP-V332W / NP-V302X / NP-V302W / NP-V302H

01h

COMPUTER

Computer1

COMPUTER

01h

02h

VIDEO

BNC(CV)

Video

BNC(CV)

VIDEO

01h

03h

－

BNC(Y/C)

S-Video

BNC(Y/C)

－

01h

06h

－

Component

－

HDMI1(078-3)

－

HDMI1(078-3)

01h

07h

USB-A

－

USB-A

－

USB-A

－

01h

21h

HDMI1

HDMI

－

HDMI

HDMI1(305-3)

HDMI1

HDMI1(305-3)

01h

22h

－

DiaplayPort

Computer3

DiaplayPort

－

01h

23h

－

SLOT

HDMI

SLOT

－

02h

01h

－

BNC

－

BNC

－

02h

06h

－

Computer2

－

HDMI2(078-3)

－

HDMI2(078-3)

02h

07h

LAN

－

HDBaseT

ETHERNET

HDBaseT

－

HDBaseT

－

LAN

－

02h

21h

HDMI2

－

HDBaseT

－

HDMI2(305-3)

HDMI2

HDMI2(305-3)

01h

27h

－

HDBaseT

－

HDBaseT

－

04h

07h

USB-B

－

USB-B

－

05h

07h

－

APPS

－

APPS

－

4. Supplementary Information by Command

097-198. PIP/PICTURE BY PICTURE REQUEST

098-198. PIP/PICTURE BY PICTURE SET

■Sub input

モデル名

NP-PA621U / NP-PA521U / NP-PA671W / NP-PA571W /

NP-PA721X / NP-PA621X

NP-PA622U / NP-PA522U / NP-PA672W / NP-PA572W /

NP-PA722X / NP-PA622X

NP-PH1202HL / NP-PH1002HL

NP-PX803UL

NP-PX602UL / NP-PX602WL

00h

OFF

01h

BNC(CV)

02h

BNC(Y/C)

03h

HDMI1

HDMI

04h

HDMI2

DATA02

05h

DisplayPort

HDMI2

SLOT

DisplayPort

06h

COMPUTER

07h

BNC

08h

ETHERNET

HDBaseT

09h

USB-A

―

ನಮಸ್ಕಾರ! NEC projector Reference manual ನೊಂದಿಗೆ ನಿಮಗೆ ಸಹಾಯ ಮಾಡಲು ನಿರ್ದಿಷ್ಟವಾಗಿ ತರಬೇತಿ ಪಡೆದ AI ಚಾಟ್‌ಬಾಟ್ ನಾನು. ನಾನು ಡಾಕ್ಯುಮೆಂಟ್ ಅನ್ನು ಸಂಪೂರ್ಣವಾಗಿ ಪರಿಶೀಲಿಸಿದ್ದೇನೆ ಮತ್ತು ನಿಮಗೆ ಅಗತ್ಯವಿರುವ ನಿಖರವಾದ ಮಾಹಿತಿಯನ್ನು ಪತ್ತೆಹಚ್ಚಲು ಅಥವಾ ವಿಷಯವನ್ನು ಸ್ಪಷ್ಟ ಮತ್ತು ಸರಳ ಪದಗಳಲ್ಲಿ ವಿವರಿಸಲು ನಾನು ನಿಮಗೆ ಸಹಾಯ ಮಾಡಬಹುದು. ನಿರ್ದಿಷ್ಟ ವೈಶಿಷ್ಟ್ಯಗಳು, ದೋಷನಿವಾರಣೆ ಹಂತಗಳು ಅಥವಾ ಸಾಮಾನ್ಯ ಬಳಕೆಯ ಕುರಿತು ನೀವು ಮಾರ್ಗದರ್ಶನವನ್ನು ಹುಡುಕುತ್ತಿರಲಿ, ನಿಮ್ಮ ಪ್ರಶ್ನೆಗಳನ್ನು ಕೇಳಲು ಮುಕ್ತವಾಗಿರಿ. ನಿಮ್ಮ ಕಾಳಜಿಗಳು ಅಥವಾ ಅಗತ್ಯಗಳ ಬಗ್ಗೆ ನೀವು ಹೆಚ್ಚು ವಿವರಗಳನ್ನು ಒದಗಿಸಿದರೆ, ನಾನು ಹೆಚ್ಚು ನಿಖರವಾಗಿ ಮತ್ತು ಪರಿಣಾಮಕಾರಿಯಾಗಿ ನಿಮಗೆ ಸಹಾಯ ಮಾಡಬಹುದು!

ಸಹಾಯಕ ಟೈಪ್ ಮಾಡುತ್ತಿದ್ದಾರೆ

ಸಹಾಯಕ ಕೀಬೋರ್ಡ್‌ನಿಂದ ಹೊರಗಿದ್ದಾರೆ. ದಯವಿಟ್ಟು, ನಂತರ ಮತ್ತೆ ಪ್ರಯತ್ನಿಸಿ.

ವಿಷಯಗಳ ಕೋಷ್ಟಕ

ಬಹು ಭಾಷೆಗಳಲ್ಲಿ ಬರೆಯಲಾದ ಡಾಕ್ಯುಮೆಂಟ್ ಅನ್ನು ನೀವು ತಲುಪಿದಂತೆ ಕಾಣುತ್ತದೆ, ನಿಮ್ಮ ಸ್ಥಳೀಯ ಭಾಷೆಯಲ್ಲದ ಒಂದು ಭಾಷೆಯೂ ಸೇರಿದಂತೆ. ನೀವು ಇಷ್ಟಪಡದ ಭಾಷೆಯಿಲ್ಲದ ಪುಟಗಳನ್ನು ತಾತ್ಕಾಲಿಕವಾಗಿ ಮರೆಮಾಡಲು ನೀವು ಕೆಳಗಿನ ಲಿಂಕ್‌ಗಳನ್ನು ಬಳಸಬಹುದು.