SMA STP3.0-3AV-40 Operating Manual

Operating manual
SUNNY TRIPOWER 3.0 / 4.0 / 5.0 / 6.0
SUN
ENGLISH
NY
ER
OW
TRIP
STP3-6-3AV-40-BE-en-13 | Version 1.3
Legal Provisions
SMA Solar Technology AG
Legal Provisions
The information contained in these documents is the property of SMA Solar Technology AG. No
part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or
by any means, be it electronic, mechanical, photographic, magnetic or otherwise, without the prior
written permission of SMA Solar Technology AG. Internal reproduction used solely for the purpose
of product evaluation or other proper use is allowed and does not require prior approval.
SMA Solar Technology AG makes no representations or warranties, express or implied, with
respect to this documentation or any of the equipment and/or software it may describe, including
(with no limitation) any implied warranties of utility, merchantability, or fitness for any particular
purpose. All such representations or warranties are expressly disclaimed. Neither SMA Solar
Technology AG nor its distributors or dealers shall be liable for any indirect, incidental, or
consequential damages under any circumstances.
The exclusion of implied warranties may not apply in all cases under some statutes, and thus the
above exclusion may not apply.
Specifications are subject to change without notice. Every attempt has been made to make this
document complete, accurate and up-to-date. Readers are cautioned, however, that product
improvements and field usage experience may cause SMA Solar Technology AG to make changes
to these specifications without advance notice, or per contract provisions in those cases where a
supply agreement requires advance notice. SMA Solar Technology AG shall not be responsible for
any damages, including indirect, incidental or consequential damages, caused by reliance on the
material presented, including, but not limited to, omissions, typographical errors, arithmetical errors
or listing errors in the content material.
SMA Warranty
You can download the current warranty conditions from the Internet at www.SMA-Solar.com.
Software Licenses
The licenses for the installed software modules (open source) can be found in the user interface of
the product.
Trademarks
All trademarks are recognized, even if not explicitly identified as such. Missing designations do not
mean that a product or brand is not a registered trademark.
SMA Solar Technology AG
Sonnenallee 1
34266 Niestetal
Germany
Tel. +49 561 9522-0
Fax +49 561 9522-100
www.SMA.de
Email: [email protected]
Status: 10/8/2019
Copyright © 2019 SMA Solar Technology AG. All rights reserved.
2
STP3-6-3AV-40-BE-en-13
Operating manual
SMA Solar Technology AG
Table of Contents
Table of Contents
1
2
Information on this Document.................................................
6
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
Validity ........................................................................................................................
Target Group..............................................................................................................
Content and Structure of this Document ...................................................................
Levels of Warning Messages ....................................................................................
Symbols in the Document ..........................................................................................
Typographies in the Document..................................................................................
Designation in the document .....................................................................................
Additional Information ...............................................................................................
6
6
6
6
7
7
8
8
Safety ........................................................................................
9
2.1
2.2
9
9
Intended Use ..............................................................................................................
IMPORTANT SAFETY INSTRUCTIONS....................................................................
3
Scope of Delivery ..................................................................... 14
4
Product Overview .................................................................... 15
4.1
4.2
4.3
4.4
4.5
5
15
16
17
19
21
22
23
Mounting................................................................................... 24
5.1
5.2
6
Product Description ....................................................................................................
Symbols on the Product .............................................................................................
Interfaces and Functions ............................................................................................
LED Signals .................................................................................................................
System Overview .......................................................................................................
4.5.1
Circuitry Overview..................................................................................
4.5.2
Communication Overview .....................................................................
Requirements for Mounting ....................................................................................... 24
Mounting the Inverter................................................................................................. 26
Electrical Connection ................................................................ 28
6.1
6.2
6.3
6.4
6.5
6.6
Overview of the Connection Area ............................................................................
AC Connection...........................................................................................................
6.2.1
Requirements for the AC Connection ....................................................
6.2.2
Connecting the Inverter to the Utility Grid ............................................
6.2.3
Connecting Additional Grounding ........................................................
Connecting the Network Cables...............................................................................
Connecting RS485 Devices.......................................................................................
Mounting the WLAN Antenna ..................................................................................
DC Connection...........................................................................................................
Operating manual
STP3-6-3AV-40-BE-en-13
28
28
28
30
31
32
34
35
35
3
Table of Contents
6.6.1
6.6.2
6.6.3
6.6.4
7
35
37
39
42
Commissioning Procedure .........................................................................................
Commissioning the Inverter........................................................................................
Selecting a configuration option ...............................................................................
Starting the Self-Test (for Italy and Dubai)................................................................
44
45
46
48
Operation ................................................................................. 49
8.1
8.2
8.3
8.4
8.5
8.6
8.7
8.8
8.9
8.10
8.11
8.12
8.13
8.14
8.15
8.16
8.17
8.18
8.19
9
Requirements for the DC Connection ....................................................
Assembling the DC Connectors .............................................................
Connecting the PV Array........................................................................
Disassembling the DC Connectors ........................................................
Commissioning ......................................................................... 44
7.1
7.2
7.3
7.4
8
SMA Solar Technology AG
Establishing a connection to the user interface ........................................................
8.1.1
Establishing a Direct Connection via Ethernet ......................................
8.1.2
Establishing a direct connection via WLAN .........................................
8.1.3
Establishing a Connection via Ethernet in the local network ...............
8.1.4
Establishing a Connection via WLAN in the Local Network ...............
Logging In and Out of the User Interface.................................................................
Start Page Design of the User Interface....................................................................
Activating the Smart Inverter Screen.........................................................................
Starting the Installation Assistant ...............................................................................
Activate WPS Function...............................................................................................
Switching WLAN On and Off...................................................................................
Switching the Dynamic Power Display Off...............................................................
Changing the Password.............................................................................................
Changing Operating Parameters..............................................................................
Configuring the Country Data Set.............................................................................
Configuring the Active Power Mode ........................................................................
Configuring the Modbus Function.............................................................................
Activating the Receipt of Control Signals (Only for Italy)........................................
Deactivating Grounding Conductor Monitoring......................................................
Setting the Rated Residual Current of the Residual-Current Device ........................
Saving the Configuration in a File.............................................................................
Adopting a Configuration from a File.......................................................................
Updating the Firmware ..............................................................................................
49
49
49
51
52
53
55
57
58
59
59
60
61
61
62
63
64
65
65
66
66
66
67
Disconnecting the Inverter from Voltage Sources ................. 69
10 Cleaning the Inverter ............................................................... 71
11 Troubleshooting........................................................................ 72
11.1
4
Forgotten Password.................................................................................................... 72
STP3-6-3AV-40-BE-en-13
Operating manual
SMA Solar Technology AG
11.2
11.3
11.4
Table of Contents
Event Messages ......................................................................................................... 73
Checking the PV System for Ground Faults.............................................................. 89
Problems with streaming services .............................................................................. 93
12 Decommissioning the Inverter................................................. 94
13 Technical Data .......................................................................... 97
13.1
13.2
13.3
13.4
13.5
13.6
13.7
DC/AC ....................................................................................................................... 97
13.1.1
Sunny Tripower 3.0 / 4.0...................................................................... 97
13.1.2
Sunny Tripower 5.0 / 6.0...................................................................... 98
General Data ............................................................................................................. 100
Climatic Conditions .................................................................................................... 101
Protective Devices ...................................................................................................... 101
Equipment ................................................................................................................... 102
Torques ....................................................................................................................... 102
Data Storage Capacity.............................................................................................. 102
14 Contact ......................................................................................103
15 EU Declaration of Conformity .................................................105
Operating manual
STP3-6-3AV-40-BE-en-13
5
1 Information on this Document
1
1.1
SMA Solar Technology AG
Information on this Document
Validity
This document is valid for:
• STP3.0-3AV-40 (Sunny Tripower 3.0) from firmware version ≥ 3.00.00.R
• STP3.0-3AV-40 (Sunny Tripower 3.0) from firmware version ≥ 3.00.00.R
• STP3.0-3AV-40 (Sunny Tripower 3.0) from firmware version ≥ 3.00.00.R
• STP3.0-3AV-40 (Sunny Tripower 3.0) from firmware version ≥ 3.00.00.R
1.2
Target Group
This document is intended for qualified persons and end users. Only qualified persons are allowed
to perform the activities marked in this document with a warning symbol and the caption
"Qualified person". Tasks that do not require any particular qualification are not marked and can
also be performed by end users. Qualified persons must have the following skills:
• Knowledge of how an inverter works and is operated
• Training in how to deal with the dangers and risks associated with installing, repairing and
using electrical devices and installations
• Training in the installation and commissioning of electrical devices and installations
• Knowledge of all applicable laws, standards and directives
• Knowledge of and compliance with this document and all safety information
1.3
Content and Structure of this Document
This document describes the mounting, installation, commissioning, configuration, operation,
troubleshooting and decommissioning of the product as well as the operation of the product user
interface.
You will find the latest version of this document and further information on the product in PDF format
and as eManual at www.SMA-Solar.com. You can also call up the eManual via the user interface
of the product.
Illustrations in this document are reduced to the essential information and may deviate from the real
product.
1.4
Levels of Warning Messages
The following levels of warning messages may occur when handling the product.
DANGER
Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
WARNING
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
6
STP3-6-3AV-40-BE-en-13
Operating manual
1 Information on this Document
SMA Solar Technology AG
CAUTION
Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE
Indicates a situation which, if not avoided, can result in property damage.
1.5
Symbols in the Document
Symbol
Explanation
Information that is important for a specific topic or goal, but is not safety-relevant
෩
Indicates a requirement for meeting a specific goal
෪
Desired result
๖
A problem that might occur
Example
Sections describing activities to be performed by qualified persons only
1.6
Typographies in the Document
Typography
Use
Example
bold
• Messages
• Terminals
• Elements on a user interface
• Elements to be selected
• Elements to be entered
• Connect the insulated
conductors to the terminals
X703:1 to X703:6.
• Enter 10 in the field
Minutes.
>
• Connects several elements to be
selected
• Select Settings > Date.
[Button]
[Key]
• Button or key to be selected or
pressed
• Select [Enter].
#
• Placeholder for variable
components (e.g., parameter
names)
• Parameter WCtlHz.Hz#
Operating manual
STP3-6-3AV-40-BE-en-13
7
1 Information on this Document
1.7
SMA Solar Technology AG
Designation in the document
Complete designation
Designation in this document
Sunny Tripower
Inverter, product
1.8
Additional Information
For more information, please go to www.SMA-Solar.com.
Title and information content
Type of information
"Application for SMA Grid Guard Code"
Form
"PUBLIC CYBER SECURITY - Guidelines for a Secure PV System
Communication"
Technical information
"SMA GRID GUARD 10.0 - Grid management services through
SMA Inverter"
Technical Information
"Efficiency and Derating"
Efficiency and derating behavior of the SMA inverters
Technical Information
"Parameters and Measured Values"
Overview of all inverter operating parameters and their configuration options
Technical Information
"SMA and SunSpec Modbus® Interface"
Information on the Modbus interface
Technical Information
"Modbus® parameters and measured values"
Device-specific register HTML file
Technical Information
"SMA SPEEDWIRE FIELDBUS"
Technical information
"RS485 Cabling Plan"
Installation Manual
"Temperature Derating"
Technical Information
8
STP3-6-3AV-40-BE-en-13
Operating manual
2 Safety
SMA Solar Technology AG
2
2.1
Safety
Intended Use
The Sunny Tripower is a transformerless PV inverter which converts the direct current of the PV array
to grid-compliant three-phase current and feeds it into the utility grid.
The product is suitable for indoor and outdoor use.
The product must only be operated with PV modules of protection class II in accordance with
IEC 61730, application class A. The PV modules must be compatible with this product.
The product is not integrated with a transformer and therefore has no galvanic isolation. The
product must not be operated with PV modules whose outputs are grounded. This can cause the
product to be destroyed. The product may be operated with PV modules whose frame is grounded.
PV modules with a high capacity to ground must only be used if their coupling capacity does not
exceed 2.25 μF (for information on how to determine the coupling capacity, see the Technical
Information "Leading Leakage Currents" at www.SMA-Solar.com).
All components must remain within their permitted operating ranges and their installation
requirements at all times.
The product must only be used in countries for which it is approved or released by SMA Solar
Technology AG and the grid operator.
Use SMA products only in accordance with the information provided in the enclosed
documentation and with the locally applicable laws, regulations, standards and directives. Any
other application may cause personal injury or property damage.
Alterations to the SMA products, e.g., changes or modifications, are only permitted with the express
written permission of SMA Solar Technology AG. Unauthorized alterations will void guarantee and
warranty claims and in most cases terminate the operating license. SMA Solar Technology AG
shall not be held liable for any damage caused by such changes.
Any use of the product other than that described in the Intended Use section does not qualify as the
intended use.
The enclosed documentation is an integral part of this product. Keep the documentation in a
convenient, dry place for future reference and observe all instructions contained therein.
This document does not replace and is not intended to replace any local, state, provincial, federal
or national laws, regulations or codes applicable to the installation, electrical safety and use of the
product. SMA Solar Technology AG assumes no responsibility for the compliance or noncompliance with such laws or codes in connection with the installation of the product.
The type label must remain permanently attached to the product.
2.2
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This section contains safety information that must be observed at all times when working.
The product has been designed and tested in accordance with international safety requirements. As
with all electrical or electronical devices, there are residual risks despite careful construction. To
prevent personal injury and property damage and to ensure long-term operation of the product,
read this section carefully and observe all safety information at all times.
Operating manual
STP3-6-3AV-40-BE-en-13
9
2 Safety
SMA Solar Technology AG
DANGER
Danger to life due to electric shock when live components or DC cables are
touched
When exposed to light, the PV modules generate high DC voltage which is present in the DC
cables. Touching live DC cables results in death or lethal injuries due to electric shock.
• Do not touch non-insulated parts or cables.
• Disconnect the product from voltage sources and make sure it cannot be reconnected
before working on the device.
• Do not disconnect the DC connectors under load.
• Wear suitable personal protective equipment for all work on the product.
DANGER
Danger to life due to electric shock when live components are touched on
opening the product
High voltages are present in the live parts and cables inside the product during operation.
Touching live parts and cables results in death or lethal injuries due to electric shock.
• Do not open the product.
DANGER
Danger to life due to electric shock from touching an ungrounded PV module
or array frame
Touching ungrounded PV modules or array frames results in death or lethal injuries due to electric
shock.
• Connect and ground the frame of the PV modules, the array frame and the electrically
conductive surfaces so that there is continuous conduction. Observe the applicable local
regulations.
DANGER
Danger to life due to electric shock when touching live system components in
case of a ground fault
If a ground fault occurs, parts of the system may still be live. Touching live parts and cables
results in death or lethal injuries due to electric shock.
• Disconnect the product from voltage sources and make sure it cannot be reconnected
before working on the device.
• Touch the cables of the PV array on the insulation only.
• Do not touch any parts of the substructure or frame of the PV array.
• Do not connect PV strings with ground faults to the inverter.
10
STP3-6-3AV-40-BE-en-13
Operating manual
2 Safety
SMA Solar Technology AG
DANGER
Danger to life due to electric shock in case of overvoltages and if surge
protection is missing
Overvoltages (e. g. in the event of a flash of lightning) can be further conducted into the building
and to other connected devices in the same network via the network cables or other data cables
if there is no surge protection. Touching live parts and cables results in death or lethal injuries due
to electric shock.
• Ensure that all devices in the same network are integrated in the existing overvoltage
protection.
• When laying the network cable outdoors, ensure that there is suitable surge protection at
the network cable transition from the product outdoors to the network inside the building.
• The Ethernet interface of the inverter is classified as "TNV-1" and offers protection against
overvoltages of up to 1.5 kV.
WARNING
Danger to life due to fire or explosion
In rare cases, an explosive gas mixture can be generated inside the inverter under fault
conditions. In this state, switching operations can cause a fire inside the inverter or explosion.
Death or lethal injuries due to hot or flying debris can result.
• In the event of a fault, do not perform any direct actions on the inverter.
• Ensure that unauthorized persons have no access to the inverter.
• Do not operate the DC load-break switch on the inverter in the event of ground fault
• Disconnect the PV array from the inverter via an external disconnection device. If there is no
disconnecting device present, wait until no more DC power is applied to the inverter.
• Disconnect the AC circuit breaker, or keep it disconnected in case it has already tripped,
and secure it against reconnection.
• Only perform work on the inverter (e.g., troubleshooting, repair work) when wearing
personal protective equipment for handling of hazardous substances (e.g., safety gloves,
eye and face protection, respiratory protection).
WARNING
Risk of injury due to toxic substances, gases and dusts.
In rare cases, damages to electronic components can result in the formation of toxic substances,
gases or dusts inside the inverter. Touching toxic substances and inhaling toxic gases and dusts
can cause skin irritation, burns or poisoning, trouble breathing and nausea.
• Only perform work on the inverter (e.g., troubleshooting, repair work) when wearing
personal protective equipment for handling of hazardous substances (e.g., safety gloves,
eye and face protection, respiratory protection).
• Ensure that unauthorized persons have no access to the inverter.
Operating manual
STP3-6-3AV-40-BE-en-13
11
2 Safety
SMA Solar Technology AG
WARNING
Danger to life due to electric shock from destruction of the measuring device
due to overvoltage
Overvoltage can damage a measuring device and result in voltage being present in the
enclosure of the measuring device. Touching the live enclosure of the measuring device results in
death or lethal injuries due to electric shock.
• Only use measuring devices with a DC input voltage range of 1000 V or higher.
CAUTION
Risk of burns due to hot enclosure parts
Some parts of the enclosure can get hot during operation. Touching hot enclosure parts can
result in burn injuries.
• During operation, do not touch any parts other than the enclosure lid of the inverter.
CAUTION
Risk of injury due to weight of product
Injuries may result if the product is lifted incorrectly or dropped while being transported or
mounted.
• Transport and lift the product carefully. Take the weight of the product into account.
• Wear suitable personal protective equipment for all work on the product.
NOTICE
Damage due to cleaning agents
The use of cleaning agents may cause damage to the product and its components.
• Clean the product and all its components only with a cloth moistened with clear water.
NOTICE
High costs due to inappropriate Internet tariff
Depending on use, the data volume of the product transferred via the Internet may vary in size.
The data volume depends, for example, on the number of inverters in the system, the frequency
of device updates, the frequency of data transfer to Sunny Portal or the use of FTP push. High
costs for the Internet connection can be the result.
• SMA Solar Technology AG recommends using an Internet flat rate.
12
STP3-6-3AV-40-BE-en-13
Operating manual
2 Safety
SMA Solar Technology AG
Change to the names and units of grid parameters to comply with the gridconnection requirements in accordance with Regulation (EU) 2016/631
(valid from April 27, 2019)
To comply with the EU grid-connection requirements (valid from April 27, 2019) the names
and units of grid parameters were changed. This change is valid from firmware version
≥ 3.00.00.R if a country data set for fulfilling the EU grid-connection requirements (valid from
2019-04-27) is set. Names and units of grid parameters for inverters with firmware version
≤ 2.99.99.R are not affected by this change and remain valid. This also applies from firmware
version ≥ 3.00.00.R if a country data set that is valid for countries outside the EU is set.
Operating manual
STP3-6-3AV-40-BE-en-13
13
3 Scope of Delivery
3
SMA Solar Technology AG
Scope of Delivery
Check the scope of delivery for completeness and any externally visible damage. Contact your
distributor if the scope of delivery is incomplete or damaged.
$
%
&
'
B
*
+
)
(
,
-
Figure 1: Components included in the scope of delivery
Position
Quantity
Designation
A
1
Inverter
B
1
Wall mounting bracket
C
3
Pan head screw M5x12
D
2
Positive DC connector
E
2
Negative DC connector
F
4
Sealing plug
G
1
AC connector
H
1
RJ45 protective sleeve: swivel nut, cable support sleeve, threaded
sleeve
I
1
WLAN antenna
J
1
Quick reference guide with password label on the rear side
The label contains the following information:
• PIC (Product Identification Code) identification key for
registering the system in Sunny Portal
• RID (Registration Identifier) registration ID for registering the
system in Sunny Portal
• WLAN password WPA2-PSK (WiFi Protected Access 2 Preshared Key) for direct connection to the inverter via WLAN
14
STP3-6-3AV-40-BE-en-13
Operating manual
4 Product Overview
SMA Solar Technology AG
4
Product Overview
4.1
Product Description
&
$
6811
%
<%2<
Figure 2: Design of the product
Position
Designation
A
DC load-break switch
B
LEDs
The LEDs indicate the operating state of the product.
C
Type label
The type label clearly identifies the product. The type label must remain permanently attached to the product. You will find the following information on
the type label:
• Device type (Model)
• Serial number (Serial No. or S/N)
• Date of manufacture
• Identification key (PIC) for registration in Sunny Portal
• Registration ID (RID) for registration in Sunny Portal
• WLAN password (WPA2-PSK) for the direct connection to the user
interface of the inverter via WLAN
• Device-specific characteristics
Operating manual
STP3-6-3AV-40-BE-en-13
15
4 Product Overview
4.2
SMA Solar Technology AG
Symbols on the Product
Symbol
Explanation
Beware of a danger zone
This symbol indicates that the product must be additionally grounded if additional grounding or equipotential bonding is required at the installation site.
Beware of electrical voltage
The product operates at high voltages.
Beware of hot surface
The product can get hot during operation.
PLQ
Danger to life due to high voltages in the inverter; observe a waiting time of 5
minutes
High voltages that can cause lethal electric shocks are present in the live components of the inverter.
Prior to performing any work on the inverter, disconnect it from all voltage
sources as described in this document.
Observe the documentation
Observe all documentation supplied with the product.
Observe the documentation
Together with the red LED, this symbol indicates an error.
Inverter
Together with the green LED, this symbol indicates the operating state of the inverter.
Data transmission
Together with the blue LED, this symbol indicates the status of the network connection.
Grounding conductor
This symbol indicates the position for connecting a grounding conductor.
Three-phase alternating current with neutral conductor
WEEE designation
Do not dispose of the product together with the household waste but in accordance with the disposal regulations for electronic waste applicable at the installation site.
16
STP3-6-3AV-40-BE-en-13
Operating manual
4 Product Overview
SMA Solar Technology AG
Symbol
Explanation
CE marking
The product complies with the requirements of the applicable EU directives.
RoHS labeling
The product complies with the requirements of the applicable EU directives.
5R+6
RCM (Regulatory Compliance Mark)
The product complies with the requirements of the applicable Australian standards.
ANATEL
The product complies with the requirements of the Brazilian standards for
telecommunication.
Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e
não pode causar interferência a sistemas operando em caráter primário.
The product complies with the Moroccan safety and EMC requirements for
electronic products.
4.3
Interfaces and Functions
The inverter is equipped with the following interfaces and functions:
User interface for monitoring and configuration
The product is equipped as standard with an integrated webserver, which provides a user interface
for configuring and monitoring the product. The product user interface can be called up via the web
browser if there is an existing connection to an end device (e.g. computer, tablet PC or
smartphone).
Smart Inverter Screen
The Smart Inverter Screen enables you to view the status display and to display the current power
and consumption on the user interface login page. This gives you an overview of the most important
inverter data without having to log into the user interface.
The Smart Inverter Screen is deactivated by default. The Smart Inverter Screen can be activated via
the user interface once the inverter has been commissioned.
SMA Speedwire
The product is equipped with SMA Speedwire as standard. SMA Speedwire is a type of
communication based on the Ethernet standard. SMA Speedwire is designed for a data transfer
rate of 100 Mbps and enables optimum communication between Speedwire devices within
systems.
Operating manual
STP3-6-3AV-40-BE-en-13
17
4 Product Overview
SMA Solar Technology AG
SMA Webconnect
The inverter is equipped with a Webconnect function as standard. The Webconnect function
enables direct data transmission between the inverters and Internet portals Sunny Portal and
Sunny Places without any additional communication device and for a maximum of 4 inverters per
visualized system. In PV systems with more than 4 inverters, there is the option of establishing data
transmission between the inverters and Sunny Portal via the data logger (e.g.,
SMA Data Manager) or distributing the inverters over several systems. If there is an existing WLAN
or Ethernet connection, you can directly access your visualized system via the web browser on your
end device.
WLAN
The product is equipped with a WLAN interface as standard. The inverter is delivered with the
WLAN interface activated as standard. If you do not want to use WLAN, you can deactivate the
WLAN interface.
Modbus
The product is equipped with a Modbus interface. The Modbus interface is deactivated by default
and must be configured as needed.
The Modbus interface of the supported SMA products is designed for industrial use – via SCADA
systems, for example – and has the following tasks:
• Remote query of measured values
• Remote setting of operating parameters
• Setpoint specifications for system control
RS485 Interface
The inverter is equipped with an RS485 interface as standard. The inverter can communicate via
cables with SMA communication products or with up to three gateways for the TS4 module
technology via the RS485 interface (information on supported SMA products at www.SMASolar.com).
Integration of TS4-R module technology
The inverter is equipped with an RS485 interface and the Cloud Connect function as standard to
integrate the TS4 module technology. Up to three gateways in line topology can be connected to
the inverter via the RS485 interface. The use of a separate Cloud Connect Advanced
communication unit is not required. The Cloud Connect function has the following functions:
• Easy integration of the TS4 module technology components into the system
• Easy commissioning and configuration via the user interface of the inverter
• Visualization and monitoring via Sunny Portal
Grid management services
The product is equipped with service functions for grid management.
Depending on the requirements of the grid operator, you can activate and configure the functions
(e.g. active power limitation) via operating parameters.
18
STP3-6-3AV-40-BE-en-13
Operating manual
4 Product Overview
SMA Solar Technology AG
Parallel Operation of the DC Inputs A and B
You have the option of operating the inverter DC inputs A and B in parallel. As a result, and as
opposed to normal operation, several parallel-connected strings can be connected to the inverter.
The inverter automatically detects the parallel operation of the DC inputs A and B.
SMA ShadeFix
The inverter is equipped with the shade management system SMA ShadeFix. SMA ShadeFix uses
an intelligent MPP tracking system to determine the operating point with the highest output during
shading conditions. With SMA ShadeFix, inverters use the best possible energy supply from the PV
modules at all times to increase yields in shaded systems. SMA ShadeFix is enabled by default. The
time interval of SMA ShadeFix is usually six minutes. This means that the inverter determines the
optimum operating point every six minutes. Depending on the PV system or shading situation, it may
be useful to adjust the time interval.
All-pole sensitive residual-current monitoring unit
The all-pole sensitive residual-current monitoring unit detects alternating and direct differential
currents. In single-phase and three-phase inverters, the integrated differential current sensor detects
the current difference between the neutral conductor and the line conductor(s). If the current
difference increases suddenly, the inverter disconnects from the utility grid.
SMA Smart Connected
SMA Smart Connected is the free monitoring of the inverter via the SMA Sunny Portal. Thanks to
SMA Smart Connected, the PV system operator and qualified person will be informed automatically
and proactively about inverter events that occur.
SMA Smart Connected is activated during registration in Sunny Portal. In order to use SMA Smart
Connected, it is necessary that the inverter is permanently connected to Sunny Portal and the data
of the PV system operator and qualified person is stored in Sunny Portal and up-to-date.
4.4
LED Signals
The LEDs indicate the operating state of the inverter.
LED signal
Explanation
The green LED is flashing
(two seconds on and
two seconds off)
Waiting for feed-in conditions
The conditions for feed-in operation are not yet met. As soon as the
conditions are met, the inverter will start feed-in operation.
The green LED flashes
quickly
Update of central processing unit
The central processing unit of the inverter is being updated.
The green LED is glowing
Feed-in operation
The inverter feeds in with a power of at least 90%.
The green LED is pulsing
Feed-in operation
The inverter is equipped with a dynamic power display via the green
LED. Depending on the power, the green LED pulses fast or slow. If
necessary, you can switch off the dynamic power display via the
green LED.
Operating manual
STP3-6-3AV-40-BE-en-13
19
4 Product Overview
SMA Solar Technology AG
LED signal
Explanation
The green LED is off
The inverter is not feeding into the utility grid.
The red LED is glowing
Event occurred
If an event occurs, a distinct event message and the corresponding
event number will be displayed in addition on the inverter user interface or in the communication product (e.g. SMA Data Manager).
The blue LED flashes slowly Communication connection is being established
for approx. one minute
The inverter is establishing a connection to a local network or is establishing a direct connection to an end device via Ethernet (e.g.
computer, tablet PC or smartphone).
The blue LED flashes quickly WPS active
for approx. two minutes
The WPS function is active.
(0.25 s on and 0.25 s off).
The blue LED is glowing
20
Communication active
There is an active connection with a local network or there is a direct connection with an end device via Ethernet (e.g. computer,
tablet PC or smartphone).
STP3-6-3AV-40-BE-en-13
Operating manual
4 Product Overview
SMA Solar Technology AG
4.5
System Overview
87,/,7<
*5,'
6811<3257$/
6RODUHQHUJ\
$OWHUQDWLQJFXUUHQW
&RPPXQLFDWLRQ
6811<
+20(0$1$*(5
60$(1(5*<0(7(5
/2$'6
&86720(56<67(0
60$396<67(0
60$6725$*(6<67(0
Operating manual
STP3-6-3AV-40-BE-en-13
21
4 Product Overview
4.5.1
SMA Solar Technology AG
Circuitry Overview
',675,%87,21%2$5'
6811<
+20(0$1$*(5
60$(1(5*<0(7(5
*5,'&211(&7,21
32,17ZLWKHQHUJ\PHWHU
RIWKHJULGRSHUDWRU
PD[$
PD[
$
PD[
$
6811<
75,32:(5
6811<%2<
6725$*(
/2$'
87,/,7<
*5,'
765
%$77(5<
6(&85(
32:(56833/<
9$
3902'8/(
&DEHO'&
&DEHO'&²
/LQHFRQGXFWRU
1HXWUDOFRQGXFWRU
*URXQGLQJFRQGXFWRU
&RQWUROFDEOH
Figure 3: Circuitry overview (example)
22
STP3-6-3AV-40-BE-en-13
Operating manual
4 Product Overview
SMA Solar Technology AG
4.5.2
Communication Overview
6811<3257$/
3XEOLF,QWHUQHW
(WKHUQHW/$1
56
&$1
5DGLR
,17(51(7
765
6811<
75,32:(5
5287(5
*$7(:$<
6:,7&+
6811<
+20(0$1$*(5
60$(1(5*<0(7(5
6811<%2<
6725$*(
%$77(5<
60$%$&.83
81,7&21752//(5
Figure 4: Design of system communication
Operating manual
STP3-6-3AV-40-BE-en-13
23
5 Mounting
5
5.1
SMA Solar Technology AG
Mounting
Requirements for Mounting
Requirements for the Mounting Location:
WARNING
Danger to life due to fire or explosion
Despite careful construction, electrical devices can cause fires. This can result in death or serious
injury.
• Do not mount the product in areas containing highly flammable materials or gases.
• Do not mount the product in potentially explosive atmospheres.
☐ A solid support surface must be available (e.g., concrete or masonry). When mounted on
drywall or similar materials, the product emits audible vibrations during operation which could
be perceived as annoying.
☐ The mounting location must be inaccessible to children.
☐ The mounting location must be suitable for the weight and dimensions of the product (see
Section 13 "Technical Data", page 97).
☐ The mounting location must not be exposed to direct solar irradiation. If the product is
exposed to direct solar irradiation, the exterior plastic parts might age prematurely and
overheating might occur. When becoming too hot, the product reduces its power output to
avoid overheating.
☐ The mounting location should be freely and safely accessible at all times without the need for
any auxiliary equipment (such as scaffolding or lifting platforms). Non-fulfillment of these
criteria may restrict servicing.
☐ The DC load-break switch of the product must always be freely accessible.
☐ All ambient conditions must be met (see Section 13, page 97).
☐ To ensure optimum operation, the ambient temperature should be between -25°C and
+40°C.
Permitted and prohibited mounting positions:
☐ The product may only be mounted in a permitted position. This will ensure that no moisture can
penetrate the product.
☐ The product should be mounted such that the LED signals can be read off without difficulty.
ƒ
Figure 5: Permitted and prohibited mounting positions
24
STP3-6-3AV-40-BE-en-13
Operating manual
5 Mounting
SMA Solar Technology AG
Dimensions for mounting:
[
[
83
‘
[
Figure 6: Position of the anchoring points(Dimensions in mm)
Recommended clearances:
If you maintain the recommended clearances, adequate heat dissipation will be ensured. Thus, you
will prevent power reduction due to excessive temperature.
☐ Maintain the recommended clearances to walls as well as to other inverters or objects.
☐ If multiple inverters are mounted in areas with high ambient temperatures, increase the
clearances between the inverters and ensure sufficient fresh-air supply.
Operating manual
STP3-6-3AV-40-BE-en-13
25
5 Mounting
SMA Solar Technology AG
Figure 7: Recommended clearances(Dimensions in mm)
5.2
Mounting the Inverter
Additionally required mounting material (not included in the scope of delivery):
☐ 3 screws, suitable for the support surface and the weight of the inverter (diameter: minimum
6 mm)
☐ 3 washers, suitable for the screws (outer diameter: minimum 18 mm)
☐ Where necessary, three screw anchors suitable for the support surface and the screws
CAUTION
Risk of injury due to weight of product
Injuries may result if the product is lifted incorrectly or dropped while being transported or
mounted.
• Transport and lift the product carefully. Take the weight of the product into account.
• Wear suitable personal protective equipment for all work on the product.
Procedure:
CAUTION
1.
Risk of injury due to damaged cables
There may be power cables or other supply lines (e.g., gas or water) routed in the wall.
• Ensure that no lines are laid in the wall which could be damaged when drilling holes.
26
STP3-6-3AV-40-BE-en-13
Operating manual
5 Mounting
SMA Solar Technology AG
2. Align the wall mounting bracket horizontally on the
wall and mark the position of the drill holes. Use at
least one hole on the right- and left-hand side and
the lower hole in the middle of the wall mounting
bracket. Tip: When mounting on a post, use the
upper and lower central holes of the wall mounting
bracket.
83
3. Set the wall mounting bracket aside and drill the marked holes.
4. Insert screw anchors into the drill holes if the support surface requires them.
5. Secure the wall mounting bracket horizontally using
screws and washers.
83
6. Hook the inverter into the wall mounting bracket.
When doing so, the two right- and left-hand keys on
the ribs on the rear side of the inverter must be
hooked into the respective keyways in the wall
mounting bracket.
83
7. Ensure that the inverter is securely in place.
8. Secure the inverter to the wall mounting bracket. To
do so, insert one pan head screw M5x12 each into
the lower screw hole on both sides of the inverter
anchorage bracket respectively and tighten them
using a Torx screwdriver (TX 25, torque: 2.5 Nm).
Operating manual
STP3-6-3AV-40-BE-en-13
27
6 Electrical Connection
6
SMA Solar Technology AG
Electrical Connection
6.1
Overview of the Connection Area
$
$
%
˗
˗
%
$&
56
&
'
(
)
*
Figure 8: Connection areas at the bottom of the inverter
Position
Designation
A
One positive and one negative DC connector, input A
B
One positive and one negative DC connector, input B
C
Jack with protective cap for RS485 communication connection
D
Network port with protective cap
E
Jack with protective cap for the WLAN antenna
F
Jack for the AC connection
G
Connection point for an additional grounding
6.2
AC Connection
6.2.1
Requirements for the AC Connection
AC cable requirements as follows:
☐ Conductor type: copper wire
☐ External diameter: 8 mm to 21 mm
☐ Conductor cross-section: 1.5 mm² to 6 mm²
☐ Insulation stripping length: 12 mm
☐ Sheath stripping length: 50 mm
☐ The cable must be dimensioned in accordance with the local and national directives for the
dimensioning of cables. The requirements for the minimum wire size derive from these
directives. Examples of factors influencing cable dimensioning are: nominal AC current, type of
cable, routing method, cable bundling, ambient temperature and maximum desired line losses
(for calculation of line losses, see the design software "Sunny Design" from software
version 2.0 at www.SMA-Solar.com).
28
STP3-6-3AV-40-BE-en-13
Operating manual
6 Electrical Connection
SMA Solar Technology AG
Grounding cable requirements:
Use of fine-stranded conductors
You can use an inflexible or a flexible, fine-stranded conductor.
• When using a fine-stranded conductor, it has to be double crimped by a ring terminal lug.
Make sure that no insulated conductor is visible when pulling or bending. This will ensure
sufficient strain relief by means of the ring terminal lug.
☐ Grounding cable cross-section: max. 10 mm²
Load-break switch and cable protection:
NOTICE
Damage to the inverter due to the use of screw-type fuses as load-break
switches
Screw-type fuses (e.g. DIAZED fuse or NEOZED fuse) are not load-break switches.
• Do not use screw-type fuses as load-break switches.
• Use a load-break switch or circuit breaker as a load disconnection unit (for information and
design examples, see the Technical Information "Circuit Breaker" at www.SMA-Solar.com).
☐ In PV systems with multiple inverters, protect each inverter with a separate circuit breaker.
Make sure to observe the maximum permissible fuse protection (see Section 13 "Technical
Data", page 97). This will prevent residual voltage from being present at the corresponding
cable after disconnection.
☐ Loads installed between the inverter and the circuit breaker must be fused separately.
Residual-current monitoring unit:
The inverter does not require an external residual-current device when operating. If local
regulations require the use of a residual-current device, the following must be observed:
☐ The inverter with firmware version 3.00.00.R is compatible with type A/B residual-current
devices that have a rated residual current of 30 mA or higher (information about the selection
of a residual-current device see technical information "Criteria for Selecting a Residual-Current
Device" at www.SMA-Solar.com). Each inverter in the system must be connected to the utility
grid via a separate residual-current device.
☐ When using residual-current devices with a rated residual current of 30 mA, the rated residual
current must be set in the inverter (see Section 8.16, page 66). In this way the inverter
reduces the operational leakage currents and prevents a false triggering of the residual-current
device.
Overvoltage category:
The inverter can be used in grids of overvoltage category III or lower in accordance with
IEC 60664-1. That means that the inverter can be permanently connected to the grid-connection
point of a building. In case of installations with long outdoor cabling routes, additional measures to
reduce overvoltage category IV to overvoltage category III are required (see the Technical
Information "Overvoltage Protection" at www.SMA-Solar.com).
Operating manual
STP3-6-3AV-40-BE-en-13
29
6 Electrical Connection
SMA Solar Technology AG
Grounding conductor monitoring:
The inverter is equipped with a grounding conductor monitoring device. This grounding conductor
monitoring device detects when there is no grounding conductor connected and disconnects the
inverter from the utility grid if this is the case. Depending on the installation site and grid
configuration, it may be advisable to disable the grounding conductor monitoring. This can be
necessary, for example, in a Delta IT system or other grid configurations if there is no neutral
conductor present and you intend to install the inverter between two line conductors. If you are
uncertain about this, contact your grid operator or SMA Solar Technology AG.
• Grounding conductor monitoring must be disabled after initial start-up depending on the grid
configuration (see Section 8.15, page 65).
Safety in accordance with IEC 62109 when the grounding conductor
monitoring is deactivated
In order to guarantee safety in accordance with IEC 62109 when the grounding conductor
monitoring is deactivated, you have to connect an additional grounding conductor to the
inverter.
• Connect an additional grounding conductor that has an cross-section of at least 10 mm
(see Section 6.2.3, page 31). This prevents touch current in the event of the grounding
conductor on the AC connector bush insert failing.
Connection of an additional grounding conductor
In some countries, an additional grounding conductor is generally required. In each case,
observe the locally applicable regulations.
• If an additional grounding conductor is required, connect the one that has an crosssection of at least 10 mm (see Section 6.2.3, page 31). This prevents touch current in
the event of the grounding conductor on the AC connector bush insert failing.
6.2.2
Connecting the Inverter to the Utility Grid
Requirements:
☐ The connection requirements of the grid operator must be met.
☐ The grid voltage must be within the permissible range. The exact operating range of the
inverter is specified in the operating parameters.
Procedure:
1. Disconnect the circuit breaker and secure it against reconnection.
2. Dismantle the AC cable by 50 mm.
3. Shorten L1, L2, L3 and N by 8 mm each so that the grounding conductor is 8 mm longer. This
ensures that the grounding conductor is the last to be pulled from the screw terminal in the
event of tensile strain.
4. Strip the insulation of L1, L2, L3, N and the grounding conductor 12 mm.
5. In the case of fine stranded wire, L1, L2, L3, N and the grounding conductor are to be fitted
with bootlace ferrules.
30
STP3-6-3AV-40-BE-en-13
Operating manual
6 Electrical Connection
SMA Solar Technology AG
6. Assemble the AC connector and connect the conductor to the AC connector (see manual of
the AC connector).
7. Ensure that all conductors are securely connected to the AC connector.
8. Plug the AC connector into the jack for the AC
connection. When doing so, align the AC connector
so that the key on the inverter AC jack is inserted
into the keyway on the AC connector bush insert.
6.2.3
Connecting Additional Grounding
If additional grounding or equipotential bonding is required locally, you can connect additional
grounding to the inverter. This prevents touch current if the grounding conductor on the AC
connector fails. The necessary ring terminal lug and the screw are included in the scope of delivery
of the inverter.
Additionally required material (not included in the scope of delivery):
☐ 1 grounding cable
Grounding cable requirements:
Use of fine-stranded conductors
You can use an inflexible or a flexible, fine-stranded conductor.
• When using a fine-stranded conductor, it has to be double crimped by a ring terminal lug.
Make sure that no insulated conductor is visible when pulling or bending. This will ensure
sufficient strain relief by means of the ring terminal lug.
☐ Grounding cable cross-section: max. 10 mm²
Procedure:
1. Strip the grounding cable insulation.
2. Insert the stripped part of the grounding cable into
the ring terminal lug and crimp using a crimping
tool.
Operating manual
STP3-6-3AV-40-BE-en-13
31
6 Electrical Connection
SMA Solar Technology AG
3. Insert the pan head screw M5x12 into the screw
hole in the ring terminal lug and screw the ring
terminal lug with screw firmly onto the connection
point for additional grounding using a Torx
screwdriver (TX 25, torque: 2.5 Nm).
6.3
Connecting the Network Cables
DANGER
Danger to life due to electric shock in case of overvoltages and if surge
protection is missing
Overvoltages (e. g. in the event of a flash of lightning) can be further conducted into the building
and to other connected devices in the same network via the network cables or other data cables
if there is no surge protection. Touching live parts and cables results in death or lethal injuries due
to electric shock.
• Ensure that all devices in the same network are integrated in the existing overvoltage
protection.
• When laying the network cable outdoors, ensure that there is suitable surge protection at
the network cable transition from the product outdoors to the network inside the building.
• The Ethernet interface of the inverter is classified as "TNV-1" and offers protection against
overvoltages of up to 1.5 kV.
NOTICE
Damage to the inverter due to moisture ingress
Moisture penetration can damage the inverter and impair its functionality.
• Connect the network cable with the supplied RJ45 protective sleeve to the inverter.
Additionally required material (not included in the scope of delivery):
☐ 1 network cable
32
STP3-6-3AV-40-BE-en-13
Operating manual
6 Electrical Connection
SMA Solar Technology AG
Network cable requirements:
The cable length and quality affect the quality of the signal. Observe the following cable
requirements.
☐ Cable type: 100BaseTx
☐ Cable category: minimum CAT5e
☐ Plug type: RJ45 of Cat5, Cat5e or higher
☐ Shielding: SF/UTP, S/UTP, SF/FTP or S/FTP
☐ Number of insulated conductor pairs and insulated conductor cross-section: at least 2 x 2 x
0.22 mm²
☐ Maximum cable length between two nodes when using patch cables: 50 m (164 ft)
☐ Maximum cable length between two nodes when using installation cables: 100 m (328 ft)
☐ UV-resistant for outdoor use.
Procedure:
DANGER
1.
Danger to life due to electric shock
• Disconnect the inverter from all voltage sources (see Section 9, page 69).
2. Unscrew the protective cap from the network port.
3. Press the cable support sleeve out of the threaded sleeve.
4. Thread the swivel nut and threaded sleeve over the
network cable. At the same time, thread the network
cable through the opening in the cable support
sleeve.
5. Press the cable support sleeve into the threaded
sleeve.
Operating manual
STP3-6-3AV-40-BE-en-13
33
6 Electrical Connection
SMA Solar Technology AG
6. Plug the network cable connector into the network
port on the inverter and screw the threaded sleeve
onto the network port thread on the inverter.
7. Screw the swivel nut onto the threaded sleeve.
8. If you would like to establish a direct connection, connect the other end of the network cable
directly to the end device.
9. If you would like to integrate the inverter into a local network, connect the other end of the
network cable to the local network (e.g., via a router).
6.4
Connecting RS485 Devices
Additionally required material (not included in the scope of delivery):
☐ One communication cable for RS485 communication
☐ One M12 plug, 4-pole
Signal assignment:
Pin connec- Signal
tor
TS4 Gateway
Sunny We Sunny Boy
Insulated
bBox
Control
conductor
color
1
GND
-
5
5
2
+12 V
+
-
-
3
Data-
B
7
8
4
Data+
A
2
3
Procedure:
DANGER
1.
Danger to life due to electric shock
• Disconnect the inverter from all voltage sources (see Section 9, page 69).
2. Assemble the M12 plug and connect the RS485 cable to the plug (see manual of the M12
connector).
34
STP3-6-3AV-40-BE-en-13
Operating manual
6 Electrical Connection
SMA Solar Technology AG
3. Ensure that all conductors are correctly connected to the M12 plug.
4. Unscrew the protective cap from the jack for the
RS485 communication connection.
5. Plug the M12 connector into the jack for the RS485
communication connection and screw tight. When
doing so, align the connector so that the key on the
inverter AC jack is inserted into the keyway on the
plug.
56
56
6.5
Mounting the WLAN Antenna
Requirement:
☐ The WLAN antenna supplied must be used.
Procedure:
DANGER
1.
Danger to life due to electric shock
• Disconnect the inverter from all voltage sources (see Section 9, page 69).
2. Remove the protective cap from the jack on the inverter.
3. Plug the WLAN antenna into the jack and screw
tight (torque: 1 Nm).
4. Pull on the WLAN antenna to ensure that the WLAN antenna is securely in place.
6.6
DC Connection
6.6.1
Requirements for the DC Connection
Connection options:
The inverter has two DC inputs, to each of which one string can be connected in normal operation.
Operating manual
STP3-6-3AV-40-BE-en-13
35
6 Electrical Connection
SMA Solar Technology AG
You have the option of operating the DC inputs A and B in parallel, and therefore of connecting
several strings to the inverter.
%
$
$
%
˗
˗
56
$&
ː
ː
B
B
Figure 9: Connection overview for normal operation
%
$
$
%
˗
˗
56
$&
ː
ː
B
B
B
Figure 10: Connection overview for parallel connection of the DC inputs A and B
36
STP3-6-3AV-40-BE-en-13
Operating manual
6 Electrical Connection
SMA Solar Technology AG
Requirements for the PV modules per input:
☐ All PV modules should be of the same type.
☐ All PV modules should be aligned and tilted identically.
☐ On the coldest day based on statistical records, the open-circuit voltage of the PV array must
never exceed the maximum input voltage of the inverter.
☐ The same number of series-connected PV modules must be connected to each string.
☐ The maximum input current per string must be maintained and must not exceed the throughfault current of the DC connectors (see Section 13 "Technical Data", page 97).
☐ The thresholds for the input voltage and the input current of the inverter must be adhered to
(see Section 13 "Technical Data", page 97).
☐ The positive connection cables of the PV modules must be equipped with positive DC
connectors (see Section 6.6.2, page 37).
☐ The negative connection cables of the PV modules must be equipped with the negative DC
connectors (see Section 6.6.2, page 37).
Use of Y adapters for parallel connection of strings
The Y adapters must not be used to interrupt the DC circuit.
• Do not use the Y adapters in the immediate vicinity of the inverter. The adapters must not
be visible or freely accessible.
• In order to interrupt the DC circuit, always disconnect the inverter as described in this
document (see Section 9, page 69).
6.6.2
Assembling the DC Connectors
DANGER
Danger to life due to electric shock when live components or DC cables are
touched
When exposed to light, the PV modules generate high DC voltage which is present in the DC
cables. Touching live DC cables results in death or lethal injuries due to electric shock.
• Do not touch non-insulated parts or cables.
• Disconnect the product from voltage sources and make sure it cannot be reconnected
before working on the device.
• Do not disconnect the DC connectors under load.
• Wear suitable personal protective equipment for all work on the product.
Operating manual
STP3-6-3AV-40-BE-en-13
37
6 Electrical Connection
SMA Solar Technology AG
NOTICE
Destruction of the inverter due to overvoltage
If the open-circuit voltage of the PV modules exceeds the maximum input voltage of the inverter,
the inverter can be destroyed due to overvoltage.
• If the open-circuit voltage of the PV modules exceeds the maximum input voltage of the
inverter, do not connect any strings to the inverter and check the design of the PV system.
For connection to the inverter, all PV module connection cables must be fitted with the DC
connectors provided. Assemble the DC connectors as described in the following. The procedure is
identical for both connectors (+ and -). The graphics for the procedure are shown for only the
positive connector as an example. Pay attention to the correct polarity when assembling the DC
connectors. The DC connectors are marked with the symbols "+" and "-".
Figure 11: Negative (A) and positive (B) DC connectors
Cable requirements:
☐ Cable type: PV1-F, UL-ZKLA, USE2
☐ External diameter: 5 mm to 8 mm
☐ Conductor cross-section: 2.5 mm² to 6 mm²
☐ Qty single wires: minimum 7
☐ Nominal voltage: minimum 1000 V
☐ Using bootlace ferrules is not allowed.
Procedure:
1. Strip 12 mm of the cable insulation.
2. Insert the stripped cable into the DC connector up to
the stop. When doing so, ensure that the stripped
cable and the DC connector are of the same
polarity.
3. Press the clamping bracket down until it audibly
snaps into place.
38
STP3-6-3AV-40-BE-en-13
Operating manual
6 Electrical Connection
SMA Solar Technology AG
☑ The stranded wire can be seen inside the
clamping bracket chamber.
4. If the stranded wire is not visible in the chamber, the cable is not correctly inserted and the
connector must be reassembled. To do this, the cable must be removed from the connector.
• Release the clamping bracket. To do so, insert
a screwdriver (blade width: 3.5 mm) into the
clamping bracket and pry the clamping bracket
open.
• Remove the cable and go back to step 2.
5. Push the swivel nut up to the thread and tighten (torque: 2 Nm).
6.6.3
Connecting the PV Array
NOTICE
Destruction of the inverter due to overvoltage
If the open-circuit voltage of the PV modules exceeds the maximum input voltage of the inverter,
the inverter can be destroyed due to overvoltage.
• If the open-circuit voltage of the PV modules exceeds the maximum input voltage of the
inverter, do not connect any strings to the inverter and check the design of the PV system.
Operating manual
STP3-6-3AV-40-BE-en-13
39
6 Electrical Connection
SMA Solar Technology AG
WARNING
Danger to life due to electric shock from destruction of the measuring device
due to overvoltage
Overvoltage can damage a measuring device and result in voltage being present in the
enclosure of the measuring device. Touching the live enclosure of the measuring device results in
death or lethal injuries due to electric shock.
• Only use measuring devices with a DC input voltage range of 1000 V or higher.
NOTICE
Damage to the DC connectors due to the use of contact cleaner of other
cleaning agents
Some contact cleaners or other cleaning agents may contain substances that decompose the
plastic of the DC connectors.
• Do not use contact cleaners or other cleaning agents for cleaning the DC connectors.
NOTICE
Damage to the inverter due to ground fault on DC side during operation
Due to the transformerless topology of the product, the occurance of ground faults on DC side
during operation can lead to irreparable damage. Damages to the product due to a faulty or
damaged DC installation are not covered by warranty. The product is equipped with a protective
device that checks whether a ground fault is present during the starting sequence. The product is
not protected during operation.
• Ensure that the DC installation is carried out correctly and no ground fault occurs during
operation.
Procedure:
1. Ensure that the circuit breaker is switched off and that it cannot be reconnected.
2. If an external DC load-break switch is installed, disconnect the external DC load-break switch
from all voltage sources.
3. Set the DC load-break switch of the inverter to
position O.
4. Measure the PV array voltage. Ensure that the maximum input voltage of the inverter is
adhered to and that there is no ground fault in the PV array.
40
STP3-6-3AV-40-BE-en-13
Operating manual
6 Electrical Connection
SMA Solar Technology AG
5. Check whether the DC connectors have the correct polarity.
If the DC connector is equipped with a DC cable of the wrong polarity, the DC connector must
be reassembled. The DC cable must always have the same polarity as the DC connector.
6. Ensure that the open-circuit voltage of the PV array does not exceed the maximum input
voltage of the inverter.
7. Connect the assembled DC connectors to the
inverter.
B
☑ The DC connectors snap into place.
8. Ensure that all DC connectors are securely in place.
NOTICE
9.
Damage to the product due to sand, dust and moisture ingress if the DC
inputs are not closed
The product is only properly sealed when all unused DC inputs are closed with DC
connectors and sealing plugs. Sand, dust and moisture penetration can damage the product
and impair its functionality.
• Seal all unused DC inputs using the DC connectors and sealing plugs as described in
the following. When doing so, do not plug the sealing plugs directly into the DC inputs
on the inverter.
10. For unused DC connectors, push down the clamping bracket and push the swivel nut up to the
thread.
11. Insert the sealing plug into the DC connector.
12. Insert the DC connectors with sealing plugs into the
corresponding DC inputs on the inverter.
B
☑ The DC connectors snap into place.
13. Ensure that the DC connectors with sealing plugs are securely in place.
Operating manual
STP3-6-3AV-40-BE-en-13
41
6 Electrical Connection
6.6.4
SMA Solar Technology AG
Disassembling the DC Connectors
To disassemble the DC connectors (e.g. due to faulty assembly), proceed as follows.
DANGER
Danger to life due to electric shock when touching exposed DC conductors or
DC plug contacts if the DC connectors are damaged or loose
The DC connectors can break or become damaged, become free of the DC cables, or no longer
be connected correctly if the DC connectors are released and disconnected incorrectly. This can
result in the DC conductors or DC plug contacts being exposed. Touching live DC conductors or
DC plug connectors will result in death or serious injury due to electric shock.
• Wear insulated gloves and use insulated tools when working on the DC connectors.
• Ensure that the DC connectors are in perfect condition and that none of the DC conductors
or DC plug contacts are exposed.
• Carefully release and remove the DC connectors as described in the following.
Procedure:
1. Release and remove the DC connectors. To do so,
insert a flat-blade screwdriver or an angled
screwdriver (blade width: 3.5 mm) into one of the
side slots and pull the DC connectors out. When
doing so, do not lever the DC connectors out, but
insert the tool into one of the side slots only to
release the locking mechanism, and do not pull on
the cable.
2. Remove the DC connector swivel nut.
3. Unlock the DC connector. To do this, insert a flatblade screwdriver (blade width: 3.5 mm) into the
side catch mechanism and pry the catch mechanism
open.
4. Carefully pull the DC connector apart.
42
STP3-6-3AV-40-BE-en-13
Operating manual
6 Electrical Connection
SMA Solar Technology AG
5. Release the clamping bracket. To do so, insert a flatblade screwdriver (blade width: 3.5 mm) into the
clamping bracket and pry the clamping bracket
open.
6. Remove the cable.
Operating manual
STP3-6-3AV-40-BE-en-13
43
7 Commissioning
7
SMA Solar Technology AG
Commissioning
7.1
Commissioning Procedure
Commissioning an inverter that is captured in a communication device
When the inverter is captured in a communication device, the communication device (e.g.
SMA Data Manager) is the unit for configuring the total system. The configuration is
transferred to all inverters in the system. The system password assigned via the communication
device is also the password for the user interface of the inverter.
• Commission the inverter (see Section 7.2, page 45).
• The initial configuration of the inverter is made via the communication device. The
configuration is transferred to the inverter and the settings of the inverter are overwritten.
• Deactivate the Webconnect function of the inverter via the Sunny Portal. This prevents
unnecessary connection attempts of the inverter with Sunny Portal.
This section describes the commissioning procedure and gives an overview of the steps you must
perform in the prescribed order.
Procedure
44
See
1.
Commission the inverter.
2.
Establish a connection to the user interface of the inverter. Section 8.1, page 49
There are various connection options to choose from for
this:
• Direct connection via WLAN
• Direct connection via Ethernet
• Connection via WLAN in the local network
• Connection via Ethernet in the local network
3.
Log into the user interface.
4.
Select the inverter configuration option. Please note that
Section 7.3, page 46
the SMA Grid Guard code for changing the grid-relevant
parameters must be available after completion of the first
ten feed-in hours or installation assistant (see "Application
for the SMA Grid Guard code" available at www.SMASolar.com).
5.
Ensure that the country data set has been configured correctly.
Section 8.11, page 62
6.
For PV systems in Italy or Dubai: Start the self-test.
Section 7.4, page 48
7.
Make further inverter settings as needed.
Section 8, page 49
STP3-6-3AV-40-BE-en-13
Section 7.2, page 45
Section 8.2, page 53
Operating manual
7 Commissioning
SMA Solar Technology AG
7.2
Commissioning the Inverter
Requirements:
☐ The AC circuit breaker must be correctly rated and mounted.
☐ The inverter must be correctly mounted.
☐ All cables must be correctly connected.
Procedure:
1. Switch on the AC circuit breaker.
2. Turn the DC load-break switch of the inverter to
position I.
☑ All three LEDs light up. The start-up phase begins.
☑ During start-up phase of the inverter, the desired firmware is being installed.
☑ All three LEDs go out again after approximately 90 seconds.
☑ The green LED starts to flash and, if the inverter is connected via Speedwire, the blue LED
also starts to flash. If the green LED is still flashing after some time, the conditions for
activating feed-in operation are not yet met. As soon as the conditions for feed-in
operation are met, the inverter starts with feed-in operation and, depending on the
available power, the green LED will light up continuously or it will pulse.
3. If th red LED is glowing, an error has occurred that must be rectified (see Section 11,
page 72).
Operating manual
STP3-6-3AV-40-BE-en-13
45
7 Commissioning
7.3
SMA Solar Technology AG
Selecting a configuration option
After having assigned the password to the Installer or User, the Configuring the Inverter page
opens.
A
B
E
D
C
Figure 12: Layout of the Configuring the Inverter page
Position
Designation
Description
A
Device information
Provides the following information:
• Device name
• Inverter serial number
• Inverter firmware version
B
User information
Provides brief information on the listed configuration
options
C
Skip configuration
Offers the option of skipping the inverter configuration and go directly to the user interface (not recommended)
D
Checkbox
Allows you to choose not to have the displayed page
displayed again when the user interface is called up
again
E
Configuration options
Provides a selection of the various configuration options
Configuration options:
On the Configuring the Inverter page, different configuration options are available to choose
from. Select one of the options and proceed for the selected option as described below. SMA
Solar Technology AG recommends carrying out the configuration with the installation assistant. This
way, you ensure that all relevant parameters are set for optimal inverter operation.
46
STP3-6-3AV-40-BE-en-13
Operating manual
7 Commissioning
SMA Solar Technology AG
• Adoption of configuration from a file
• Configuration with the installation assistant (recommended)
• Manual configuration
Accepting the settings
Saving the made settings is indicated by an hourglass symbol on the user interface. If the DC
voltage is sufficient, the data is transferred directly to the inverter and accepted. If the DC
voltage is too low (e. g. in the evening), the settings are saved, but they cannot be directly
transferred to or accepted by the inverter. As long as the inverter has not yet received and
accepted the settings, the hourglass symbol will continue to be displayed on the user interface.
The settings will be accepted when there is sufficient DC voltage applied and the inverter
restarts. As soon as the hourglass symbol appears on the user interface, the settings have been
saved. The settings will not be lost. You can log off of the user interface and leave the system.
Adopting the Configuration from a File
You can adopt the inverter configuration from a file. To do this, there must be an inverter
configuration saved to a file.
Procedure:
1. Select the configuration option Adopting configuration from a file.
2. Select [Browse...] and select the desired file.
3. Select [Import file].
Configuring the Installation Assistant (Recommended)
1. Select the configuration option Configuration with Installation Assistant.
☑ The installation assistant will open.
2. Follow the installation assistant steps and make the settings appropriate for your system.
3. For every setting made in a step, select [Save and next].
☑ In the last step, all made settings are listed in a summary.
4. To correct settings you made, select [Back], navigate to the desired step, correct settings and
select [Save and continue].
5. Once all settings are correct, select [Next] in the summary.
6. To save the settings to a file, select [Export a summary] and save the file on your end
device.
7. To export all parameters and their settings, select [Export all parameters]. This exports all
parameters and their settings into an HTML file.
☑ The start page of the user interface opens.
Manual configuration
You can configure the inverter manually by setting the desired parameters.
Operating manual
STP3-6-3AV-40-BE-en-13
47
7 Commissioning
SMA Solar Technology AG
Procedure:
1. Select the configuration option Manual Configuration.
☑ The Device Parameters menu on the user interface will open and all available
parameter groups of the inverter will be displayed.
2. Select [Edit parameters].
3. Select the desired parameter group.
☑ All available parameters of the parameter group will be displayed.
4. Set the desired parameters.
5. Select [Save all].
☑ The inverter parameters are set.
7.4
Starting the Self-Test (for Italy and Dubai)
The self-test is only required for inverters that are to be commissioned in Italy or Dubai. The Italian
standard CEI 0-21 and the DEWA (Dubai Electricity and Water Authority) stipulate that all inverters
that feed into the utility grid are equipped with a self-test function. During the self-test, the inverter
will consecutively check the reaction times for overvoltage, undervoltage, maximum frequency and
minimum frequency.
The self-test changes the upper and lower disconnection values for each protective function on a
linear basis for frequency monitoring and voltage monitoring. As soon as the measured value
exceeds the permitted disconnection threshold, the inverter disconnects from the utility grid. In this
way, the inverter determines the reaction time and checks itself.
After the self-test has been completed, the inverter automatically switches back to feed-in operation,
resets the original disconnection conditions and connects to the utility grid. The test takes
approximately three minutes.
Requirements:
☐ The country data set of the inverter must be set to CEI 0-21 internal or DEWA 2016
internal.
Procedure:
1. Select the menu Device Configuration.
2. Select [Settings].
3. Select [Starting the Self-Test] in the subsequent context menu.
4. Follow the instructions appearing in the dialog and save the report of the self-test where
necessary.
48
STP3-6-3AV-40-BE-en-13
Operating manual
8 Operation
SMA Solar Technology AG
8
Operation
8.1
Establishing a connection to the user interface
8.1.1
Establishing a Direct Connection via Ethernet
Requirements:
☐ The product must be commissioned.
☐ An end device (e.g. computer) with an Ethernet interface must be available.
☐ The product must be connected directly to the end device.
☐ The respective latest version of one of the following web browsers must be installed: Chrome,
Edge, Firefox, Internet Explorer or Safari.
☐ The SMA Grid Guard code of the Installer must be available for the changing of grid-relevant
settings after completion of the first ten feed-in hours or installation assistant (see "Application
for SMA Grid Guard Code" at www.SMA-Solar.com).
IP address of the inverter
• Standard inverter IP address for the direct connection via Ethernet: 169.254.12.3
Procedure:
1. Open the web browser of your end device, enter the IP address 169.254.12.3 in the address
bar and press the enter key.
2.
Web browser signals a security vulnerability
After the IP address has been entered, a message might appear indicating that the
connection to the user interface of the product is not secure. SMA Solar Technology AG
guarantees the security of the user interface.
• Continue loading the user interface.
☑ The login page of the user interface opens.
8.1.2
Establishing a direct connection via WLAN
Requirements:
☐ The product must be commissioned.
☐ An end device (e.g. computer, tablet PC or smartphone) must be available.
☐ The respective latest version of one of the following web browsers must be installed: Chrome,
Edge, Firefox, Internet Explorer or Safari.
☐ JavaScript must be enabled in the web browser of the end device.
☐ The SMA Grid Guard code of the Installer must be available for the changing of grid-relevant
settings after completion of the first ten feed-in hours or installation assistant (see "Application
for SMA Grid Guard Code" at www.SMA-Solar.com).
Operating manual
STP3-6-3AV-40-BE-en-13
49
8 Operation
SMA Solar Technology AG
SSID, IP address and WLAN password
• SSID in WLAN: SMA[serial number] (e.g. SMA0123456789)
• Device-specific WLAN password: see WPA2-PSK on the type label of the product or the
rear side of the manual included in delivery
• Standard access address for a direct connection via WLAN outside of a local network:
http://smalogin.net or 192.168.12.3
Importing and exporting files with end devices having an iOS operating
system is not possible.
For technical reasons, importing and exporting files (e.g., importing an inverter configuration,
saving the current inverter configuration or exporting events and parameters) is not possible
with mobile end devices having an iOS operating system.
• Use an end device that does not have an iOS operating system for importing and
exporting files.
You have several options to connect the product to an end device. The procedure can be different
depending on the end devices. If the procedures described do not apply to your end device,
establish the direct connection via WLAN as described in the manual of your end device.
The following connection options ar available:
• Connection with WPS
• Connection with WLAN network search
Connection with WPS
Requirement:
☐ The end device must have a WPS function.
Procedure:
1. Enable the WPS function on the inverter. To do this, tap on the enclosure lid of the inverter
twice.
☑ The blue LED flashes quickly for approx. two minutes. The WPS function is active during
this time.
2. Enable the WPS function on your end device.
☑ The end device automatically connects to the inverter. The web browser of your end
device opens and the login page of the user interface is displayed.
3. If the web browser of your end device does not open automatically and the login page of the
user interface is not displayed, open the web browser and enter http://smalogin.net in the
address bar.
Connection with WLAN network search
1. Search for WLAN networks with your end device.
2. Select the SSID of the inverter SMA[serial number] in the list with the found WLAN
networks.
50
STP3-6-3AV-40-BE-en-13
Operating manual
8 Operation
SMA Solar Technology AG
3. Enter the device-specific WLAN password (see WPA2-PSK on the type label of the product or
the rear side of the manual included in delivery).
4. Open the web browser of your end device and enter http://smalogin.net in the address
bar.
☑ The login page of the user interface is displayed.
5. If the login page of the user interface does not open, enter the IP address 192.168.12.3 or, if
your end device supports mDNS services, SMA[serial number].local or http://SMA[serial
number] in the address bar of the web browser.
8.1.3
Establishing a Connection via Ethernet in the local
network
New IP address for connecting with a local network
If the product is connected to a local network (e.g. via a router), the product will receive a new
IP address. Depending on the type of configuration, the new IP address will be assigned
automatically by the DHCP server (router) or manually by you. Upon completion of the
configuration, the product can only be reached via the following access addresses:
• Generally applicable access address: IP address manually assigned or assigned by the
DHCP server (router) (identification via network scanner software or network
configuration of the router).
• Access address for Apple and Linux systems: SMA[serial number].local (e.g.
SMA0123456789.local)
• Access address for Windows and Android systems: http://SMA[serial number] (e.g.,
http://SMA0123456789)
Requirements:
☐ The product must be connected to the local network via a network cable (e.g. via a router).
☐ The product must be integrated into the local network. Tip: There are various methods of
integrating the product into the local network with the aid of the installation assistant.
☐ An end device (e.g. computer, tablet PC or smartphone) must be available.
☐ The end device must be in the same local network as the product.
☐ The respective latest version of one of the following web browsers must be installed: Chrome,
Edge, Firefox, Internet Explorer or Safari.
☐ The SMA Grid Guard code of the Installer must be available for the changing of grid-relevant
settings after completion of the first ten feed-in hours or installation assistant (see "Application
for SMA Grid Guard Code" at www.SMA-Solar.com).
Procedure:
1. Open the web browser of your end device, enter the IP address of the inverter in the address
bar of the web browser and press the enter key.
Operating manual
STP3-6-3AV-40-BE-en-13
51
8 Operation
SMA Solar Technology AG
Web browser signals a security vulnerability
2.
After the IP address has been confirmed by pressing the enter key, a message might
appear indicating that the connection to the user interface of the inverter is not secure.
SMA Solar Technology AG guarantees that calling up the user interface is secure.
• Continue loading the user interface.
☑ The login page of the user interface opens.
8.1.4
Establishing a Connection via WLAN in the Local Network
New IP address for connecting with a local network
If the product is connected to a local network (e.g. via a router), the product will receive a new
IP address. Depending on the type of configuration, the new IP address will be assigned
automatically by the DHCP server (router) or manually by you. Upon completion of the
configuration, the product can only be reached via the following access addresses:
• Generally applicable access address: IP address manually assigned or assigned by the
DHCP server (router) (identification via network scanner software or network
configuration of the router).
• Access address for Apple and Linux systems: SMA[serial number].local (e.g.
SMA0123456789.local)
• Access address for Windows and Android systems: http://SMA[serial number] (e.g.,
http://SMA0123456789)
Requirements:
☐ The product must be commissioned.
☐ The product must be integrated into the local network. Tip: There are various methods of
integrating the product into the local network with the aid of the installation assistant.
☐ An end device (e.g. computer, tablet PC or smartphone) must be available.
☐ The end device must be in the same local network as the product.
☐ The respective latest version of one of the following web browsers must be installed: Chrome,
Edge, Firefox, Internet Explorer or Safari.
☐ The SMA Grid Guard code of the Installer must be available for the changing of grid-relevant
settings after completion of the first ten feed-in hours or installation assistant (see "Application
for SMA Grid Guard Code" at www.SMA-Solar.com).
Importing and exporting files with end devices having an iOS operating
system is not possible.
For technical reasons, importing and exporting files (e.g., importing an inverter configuration,
saving the current inverter configuration or exporting events and parameters) is not possible
with mobile end devices having an iOS operating system.
• Use an end device that does not have an iOS operating system for importing and
exporting files.
52
STP3-6-3AV-40-BE-en-13
Operating manual
8 Operation
SMA Solar Technology AG
Procedure:
• Enter the IP address of the inverter in the address bar of the web browser.
☑ The login page of the user interface opens.
8.2
Logging In and Out of the User Interface
After a connection to the user interface of the inverter has been established, the login page opens.
Log onto the user interface as described below.
Usage of cookies
For the correct display of the user interface, cookies are required. The cookies are used for
convenience only. By using this user interface you agree to the placement of cookies.
Log in as Installer or User for the First Time
Password assignment for user and installer
The passwords for the user groups Installer and User must be assigned when accessing the
user interface for the first time. If the inverter was registered in a communication device (e.g.,
SMA Data Manager) and the system password was assigned, the system password is also the
installer password. In this case, only the user password must be assigned.
• If you as a specialist assign the user password, only pass the password on to persons to
access the inverter data via the user interface.
• If you as a user assign the installer password, only pass the password on to persons to
receive access to the system.
Installer password for inverters registered in a communication device or in
Sunny Portal
To be able to register the inverter in a communication device (e.g., SMA Data Manager) or in
a Sunny Portal system, the password for the user group Installer must match the system
password. If you assign a password for the user group Installer via the user interface of the
inverter, the same password must also be used as the system password.
• Assign a uniform installer password to all SMA devices in the system.
Procedure:
1. In the drop-down list Language, select the desired language.
2. In the Password field, enter a password for the User user group.
3. In the Repeat password field, enter the password again.
4. Click on Save.
5. In the New password field, enter a password for the Installer user group. Assign a uniform
password to all SMA devices to be registered in a system. The installer password is also the
system password.
6. In the Repeat password field, enter the password again.
7. Click on Save and log in.
☑ The Configuring the Inverter page opens.
Operating manual
STP3-6-3AV-40-BE-en-13
53
8 Operation
SMA Solar Technology AG
Log in as the User or Installer
1. In the drop-down list Language, select the desired language.
2. In the User group drop-down list, select the entry Installer or User.
3. Enter the password in the field Password.
4. Select Login.
☑ The start page of the user interface opens.
Log Out as the User or Installer
1. On the right-hand side of the menu bar, select the menu User Settings.
2. In the subsequent context menu, select [Logout].
☑ The login page of the user interface opens. The logout was successful.
54
STP3-6-3AV-40-BE-en-13
Operating manual
8 Operation
SMA Solar Technology AG
8.3
Start Page Design of the User Interface
A
B
C
F
E
D
Figure 13: Design of the user interface's start page (example)
Operating manual
STP3-6-3AV-40-BE-en-13
55
8 Operation
SMA Solar Technology AG
Position
Designation
Description
A
Menu
Provides the following functions:
• Home
Opens the user interface homepage
• Instantaneous values
Current measured values of the inverter
• Device Parameters
The various operating parameters of the inverter can
be viewed and configured here depending on the
user group.
• Events
All events that have occurred in the selected time
period are displayed here. The event types are
Information, Warning and Error. Currently
existing events of the types Error and Warning will
be additionally displayed in the Device status
viewlet. However, only the higher-priority event is
displayed. If, for example, there is a Warning and an
Error present at the same time, only the Error will be
displayed.
• Device configuration
Various settings for the inverter can be made here.
The selection available is dependent on which user
group you are logged in as and the operating system
of the device with which the user interface has been
called up.
• Data
You will find all data that is saved in the internal
memory of the inverter or on an external storage
medium on this page.
B
User settings
Provides the following functions, depending on the user
group logged in:
• Starting the installation assistant
• SMA Grid Guard login
• Logout
C
Help
Provides the following functions:
• Displaying information on Open Source licenses used
• Link to the website of SMA Solar Technology AG
56
STP3-6-3AV-40-BE-en-13
Operating manual
8 Operation
SMA Solar Technology AG
Position
Designation
Description
D
Status bar
Displays the following information:
• Inverter serial number
• Inverter firmware version
• IP address of the inverter within the local network
and/or IP address of the inverter during WLAN
connection
• With WLAN connection: Signal strength of WLAN
connection
• User group logged in
• Date and device time of the inverter
E
Current power and cur- Temporal progression of the PV power and the power
rent consumption
consumption of the household over the selected time period. Please note, the power consumption will only be displayed if an energy meter is installed in the PV system.
F
Status display
8.4
The various areas display information on the current status
of the PV system.
• Device status
Displays whether the inverter is currently in a faultfree operating state or whether there is an Error or
Warning present.
• Current power
Displays the power currently being generated by the
inverter.
• Modular technology status
Displays how many module technology components
are available and the status of each one (only
present if the TS4 module technology is connected).
• Yield
Displays the energy yield of the inverter.
• Grid supply
Displays the energy supply from the utility grid.
• Power at the grid connection point
Indicates which power is currently fed in or obtained
at the grid-connection point.
Activating the Smart Inverter Screen
With the Smart Inverter Screen, the most important inverter data is displayed directly on the user
interface login page. To activate the Smart Inverter Screen, proceed as listed in the following.
Operating manual
STP3-6-3AV-40-BE-en-13
57
8 Operation
SMA Solar Technology AG
Procedure:
1. Activate the user interface (see Section 8.1, page 49).
2. Log in as Installer or User.
3. Select the menu User Settings (see Section 8.3, page 55) on the start page of the user
interface.
4. Select [Smart Inverter Screen].
☑ The Smart Inverter Screen has been activated.
8.5
Starting the Installation Assistant
The installation assistant leads you step-by-step through the steps necessary for the initial
configuration of the inverter.
Layout of the installation assistant
A
C
B
Figure 14: Layout of the installation assistant (example)
Position
Designation
Description
A
Configuration steps
Overview of the installation assistant steps. The number of
steps depends on the type of device and the additionally
installed modules. The current step is highlighted in blue.
B
User information
Information about the current configuration step and the
setting options of the configuration step.
C
Configuration field
You can make settings in this field.
Requirement:
☐ When configuring after completion of the first ten feed-in hours or after exiting the installation
assistant, the SMA Grid Guard code must be available in order to change the grid-relevant
parameters (see "Application for SMA Grid Guard Code" at www.SMA-Solar.com).
58
STP3-6-3AV-40-BE-en-13
Operating manual
8 Operation
SMA Solar Technology AG
Procedure:
1. Open the user interface (see Section 8.1, page 49).
2. Log in as Installer.
3. Select the menu User Settings (see Section 8.3, page 55) on the start page of the user
interface.
4. In the context menu, select [Starting the installation assistant].
☑ The installation assistant will open.
8.6
Activate WPS Function
The WPS function can be used for different purposes:
• Automatic connection to a network (e.g. via router)
• Direct connection between the product and an end device
Depending on the intended application of the WPS function, the procedure for activation will vary.
Activating WPS function for automatic connection to a network
Requirements:
☐ WLAN must be activated in the product.
☐ WPS must be activated on the router.
Procedure:
1. Activate the user interface (see Section 8.1, page 49).
2. Log in as Installer.
3. Start the installation assistant (see Section 8.5, page 58).
4. Select Network configuration.
5. Select WPS for WLAN network button in the WLAN tab.
6. Select Activate WPS.
7. Select Save and next and exit the installation assistant.
☑ The WPS function is activated and the automatic connection to the network can be
established.
Activating the WPS function for direct connection to the end device.
• Activate the WPS function on the inverter. To do this, tap on the enclosure lid of the inverter
twice.
☑ The blue LED flashes quickly for approx. two minutes. The WPS function is active during
this time.
8.7
Switching WLAN On and Off
The inverter is equipped with an activated WLAN interface as standard. If you do not want to use
WLAN, you can switch the WLAN function off and switch it on again whenever needed. In doing
so, you can switch the WLAN direct connection and the WLAN connection in the local network on
independently of each other.
Operating manual
STP3-6-3AV-40-BE-en-13
59
8 Operation
SMA Solar Technology AG
Switching on the WLAN function only possible via Ethernet connection
If you switch off both the WLAN function for the direct connection and for the connection in
the local network, access to the inverter user interface and therefore reactivation of the WLAN
interface is only possible via an Ethernet connection.
The basic procedure for changing operating parameters is explained in another section (see
Section 8.10 "Changing Operating Parameters", page 61).
Switching WLAN Off
If you would like to switch the WLAN function off completely, you must switch off both the direct
connection and the connection in the local network.
Procedure:
• To switch off the direct connection in the parameter group PV system communication >
WLAN, select the parameter Soft-access-point is turned on and set this to No.
• To switch off the connection in the local network in the parameter group PV system
communication > WLAN, select the parameter WLAN is turned on and set this to No.
Switching WLAN On
If you have switched the WLAN function for direct connection or for connection in the local network
off, you can switch the WLAN function back on in accordance with the following procedure.
Requirement:
☐ If the WLAN function was previously switched off completely, the inverter must be connected
to a computer or router via Ethernet.
Procedure:
• To switch on the WLAN direct connection, in the parameter group PV system
communication > WLAN, select the parameter Soft-access-point is turned on and set this
to Yes.
• To switch on the WLAN connection in the local network, in the parameter group System
communication > WLAN, select the parameter WLAN is turned on and set this to Yes.
8.8
Switching the Dynamic Power Display Off
As standard, the inverter signals its power dynamically via the pulsing of the green LED. When
doing so, the LED flashes on and off uniformly or is permanently lit at full power. The various
gradations are related here to the set active power limit of the inverter. If this display is not desired,
switch this function off in accordance with the following procedure. Once this has been done, the
green LED is lit permanently to signalize feed-in operation.
The basic procedure for changing operating parameters is explained in another section (see
Section 8.10 "Changing Operating Parameters", page 61).
Procedure:
• In the parameter group Device > Operation, select the parameter Dynamic power
display via green LED and set this to Off.
60
STP3-6-3AV-40-BE-en-13
Operating manual
8 Operation
SMA Solar Technology AG
8.9
Changing the Password
The password for the inverter can be changed for both user groups. Furthermore, the user group
Installer can change the password for the user group User as well as its own password.
PV systems registered in a communication product
With PV systems that are registered in a communication product (e.g. Sunny Portal,
Cluster Controller), you can also assign a new password for the user group Installer via the
communication product. The password for the user group Installer is also the system
password. If you assign a password for the user group Installer via the user interface of the
inverter that does not correspond to the system password in the communication product, the
inverter can no longer be reached by the communication product.
• Ensure that the password for the user group Installer is the same as the system password
in the communication product.
Procedure:
1. Activate the user interface (see Section 8.1, page 49).
2. Log into the user interface (see Section 8.2, page 53).
3. Call up the menu Device Parameters.
4. Select [Edit parameters].
5. In the parameter group User Rights > Access Control change the password of the desired
user group.
6. Select [Save all] to save the changes.
8.10 Changing Operating Parameters
The operating parameters of the inverter are set to certain values by default. You can change the
operating parameters to optimize the performance of the inverter.
This section describes the basic procedure for changing operating parameters. Always change
operating parameters as described in this section. Some function-sensitive parameters can only be
viewed by qualified persons and can only be changed by qualified persons by entering the
personal SMA Grid Guard code.
No configuration via Sunny Explorer
Sunny Explorer does not support the configuration of inverters with their own user interface.
The inverter can be detected via Sunny Explorer, however it is expressly not recommended to
use Sunny Explorer to configure this inverter. SMA Solar Technology AG does not accept
liability for missing or incorrect data and possibly resulting yield losses.
• Use the user interface for the configuration of the inverter.
Requirements:
☐ Changes to grid-relevant parameters must be approved by the responsible grid operator.
Procedure:
1. Open the user interface (see Section 8.1, page 49).
2. Log into the user interface (see Section 8.2, page 53).
Operating manual
STP3-6-3AV-40-BE-en-13
61
8 Operation
SMA Solar Technology AG
3. Call up the menu Device Parameters.
4. Click on [Edit parameters].
5. Log in using the SMA Grid Guard code to change those parameters designated by a lock
(only for installers):
• Select the menu User Settings (see Section 8.3, page 55).
• In the subsequent context menu, select [SMA Grid Guard login].
• Enter the SMA Grid Guard code and select [Login].
6. Expand the parameter group that contains the parameter which is to be configured.
7. Change the desired parameters.
8. Select [Save all] to save the changes.
☑ The inverter parameters are set.
Accepting the settings
Saving the made settings is indicated by an hourglass symbol on the user interface. If the DC
voltage is sufficient, the data is transferred directly to the inverter and accepted. If the DC
voltage is too low (e. g. in the evening), the settings are saved, but they cannot be directly
transferred to or accepted by the inverter. As long as the inverter has not yet received and
accepted the settings, the hourglass symbol will continue to be displayed on the user interface.
The settings will be accepted when there is sufficient DC voltage applied and the inverter
restarts. As soon as the hourglass symbol appears on the user interface, the settings have been
saved. The settings will not be lost. You can log off of the user interface and leave the system.
8.11 Configuring the Country Data Set
By default, the inverter is set to a universally valid country data set. You must adjust the country
data set for the installation site.
The country data set must be set correctly.
If you select a country data set which is not valid for your country and purpose, it can cause a
disturbance in the PV system and lead to problems with the grid operator. When selecting the
country data set, you must always observe the locally applicable standards and directives as
well as the properties of the PV system (e.g. PV system size, grid-connection point).
• If you are not sure which standards and directives are valid for your country or purpose,
contact the grid operator.
62
STP3-6-3AV-40-BE-en-13
Operating manual
8 Operation
SMA Solar Technology AG
Change to the names and units of grid parameters to comply with the gridconnection requirements in accordance with Regulation (EU) 2016/631
(valid from April 27, 2019)
To comply with the EU grid-connection requirements (valid from April 27, 2019) the names
and units of grid parameters were changed. This change is valid from firmware version
≥ 3.00.00.R if a country data set for fulfilling the EU grid-connection requirements (valid from
2019-04-27) is set. Names and units of grid parameters for inverters with firmware version
≤ 2.99.99.R are not affected by this change and remain valid. This also applies from firmware
version ≥ 3.00.00.R if a country data set that is valid for countries outside the EU is set.
The basic procedure for changing operating parameters is explained in another section (see
Section 8.10 "Changing Operating Parameters", page 61).
Procedure:
• In the parameter group Grid monitoring > Grid monitoring select the parameter Set
country standard and set the required country data set.
8.12 Configuring the Active Power Mode
Starting the installation assistant
1. Open the user interface (see Section 8.1, page 49).
2. Log in as Installer.
3. Start the installation assistant (see Section 8.5, page 58).
4. Select [Save and continue] after each step up until the step Grid management service.
5. Make the settings as described in the following.
Make the settings for systems with external setpoint
1. Set theGrid connection point regulation to [Off].
2. In the tab Active power mode set the switch Active power setpoint to [On].
3. In the drop-down list Operating mode active power setpoint, select the entry External
setpoint.
4. In the drop-down list Fallback behavior, select the entry Apply fallback values.
5. In the field Fallback value of the maximum active power enter the value to which the
inverter is to limit its nominal power in case of a communication failure to the higher control
unit at the end of the timeout time.
6. In the field Timeout, enter the time that the inverter is to wait before it limits its nominal power
to the set fallback value.
7. If, in the event of a 0% or 0 W specification, the inverter is not permitted to feed small amounts
of active power into the utility grid, select the entry Yes in the drop-down list Grid
disconnection for 0% active power setpoint. This ensures that in the event of a 0% or 0 W
specification, the inverter disconnects from the utility grid and does not feed in active power.
Operating manual
STP3-6-3AV-40-BE-en-13
63
8 Operation
SMA Solar Technology AG
Make the settings for systems with manual setpoint
1. In the tab Active power mode set the switch Grid connection point regulation to [On].
2. Enter the total PV array power in the field Nominal PV system power.
3. In the drop-down list Operating mode active power setting, select whether active power
limitation is to be performed via a fixed specification in percent or in watts.
4. In the field Set active power limit, enter the value to which the active power at the gridconnection point is to be limited. The value must be set to 0 for zero power output.
5. Set the Active power setpoint to [On].
6. Select the entry Manual setpoint in % or Manual setpoint in W for manual specification
and enter the respective setpoint value.
7. If the inverter itself is to control active power at the grid-connection point, perform the following
steps:
• In the drop-down list Operating mode active power setting, select the entry External
setting.
• In the drop-down list Fallback behavior, select the entry Apply fallback values.
• In the drop-down list Grid disconnection for 0% active power setting select the entry
No.
8.13 Configuring the Modbus Function
The Modbus interface is deactivated by default and the communication ports 502 set.
In order to access SMA invertes with SMA Modbus® or SunSpec® Modbus®, the Modbus interface
must be activated. After activating the interface, the communication ports of both IP protocols can
be changed. For information on commissioning and configuration of the Modbus interface, see the
technical information "SMA and SunSpec Modbus® Interface" at www.SMA-Solar.com.
For information on which Modbus registers are supported, see the technical information "Modbus®
parameters and measured values" at www.SMA-Solar.com.
Data security during enabled Modbus interface
If you enable the Modbus interface, there is a risk that unauthorized users may access and
manipulate the data or devices in your PV system.
To ensure data security, take appropriate protective measures such as:
• Set up a firewall.
• Close unnecessary network ports.
• Only enable remote access via VPN tunnel.
• Do not set up port forwarding at the communication port in use.
• In order to disable the Modbus interface, reset the inverter to the default settings or
disable the parameter again.
Procedure:
• Activate the Modbus interface and adjust the communication ports if necessary (see the
technical information "SMA and SunSpec Modbus® Interface" at www.SMA-Solar.com).
64
STP3-6-3AV-40-BE-en-13
Operating manual
8 Operation
SMA Solar Technology AG
8.14 Activating the Receipt of Control Signals (Only for
Italy)
In order for PV systems in Italy to receive control commands from the grid operator, set the
following parameters.
The basic procedure for changing operating parameters is explained in another section (see
Section 8.10 "Changing Operating Parameters", page 61).
Parameter
Value/range
Resolution
Default
Application ID
0 to 16384
1
16384
1
01:0C:CD:01:00:00
GOOSE-Mac address 01:0C:CD:01:00:00 to
01:0C:CD:01:02:00
Procedure:
1. Select the parameter group External communication > IEC 61850 configuration.
2. In the field Application ID, enter the application ID of the grid operator gateway. You will
receive this value from your grid operator. You can enter a value between 0 and 16384. The
value 16384 indicates "deactivated".
3. In the field GOOSE-Mac address, enter the MAC address of the grid operator gateway
from which the inverter is to receive the control commands. You will receive this value from
your grid operator.
☑ The receipt of control signals from the grid operator is activated.
8.15 Deactivating Grounding Conductor Monitoring
If the inverter is to be installed in an IT network or another grid configuration in which deactivation
of the grounding conductor monitoring is required, deactivate the grounding conductor monitoring
as follows.
The basic procedure for changing operating parameters is explained in another section (see
Section 8.10 "Changing Operating Parameters", page 61).
Procedure:
• In the parameter group Grid monitoring > Grid monitoring > Country standard set the
parameter PE connection monitoring to Off.
Operating manual
STP3-6-3AV-40-BE-en-13
65
8 Operation
SMA Solar Technology AG
8.16 Setting the Rated Residual Current of the ResidualCurrent Device
When using residual-current devices with a rated residual current of 30 mA, set the rated residual
current to 30 mA. In this way the inverter reduces the operational leakage currents and prevents a
false triggering of the residual-current device (for further information, see technical information
"Leading Leakage Currents" at www.SMA-Solar.com).
The basic procedure for changing operating parameters is explained in another section (see
Section 8.10 "Changing Operating Parameters", page 61).
Procedure:
• Select the parameter RCD adjustment and set it to 30 mA.
8.17 Saving the Configuration in a File
You can save the current configuration of the inverter in a file. You can use this file as a data
backup for this inverter and then import this file into this inverter again or another inverter from the
same type or device family to configure the inverter. When saving, only the device parameters will
be saved, not any passwords.
Procedure:
1. Activate the user interface (see Section 8.1, page 49).
2. Log into the user interface (see Section 8.2, page 53).
3. Select the menu Device Configuration.
4. Select [Settings].
5. In the context menu, select [Saving the configuration in a file].
6. Follow the instructions in the dialog.
8.18 Adopting a Configuration from a File
To configure the inverter, you can adopt the configuration from a file. To be able to do this, you
must first save the configuration of another inverter from the same type or device family in a file (see
Section 8.17 "Saving the Configuration in a File", page 66). When saving, only the device
parameters will be adopted, not any passwords.
Requirements:
☐ Changes to grid-relevant parameters must be approved by the responsible grid operator.
☐ The SMA Grid Guard code must be available (see "Application for SMA Grid Guard Code"
at www.SMA-Solar.com).
Procedure:
1. Open the user interface (see Section 8.1, page 49).
2. Log into the user interface as an Installer (see Section 8.2, page 53).
66
STP3-6-3AV-40-BE-en-13
Operating manual
8 Operation
SMA Solar Technology AG
3. Select the menu Device Configuration.
4. Select [Settings].
5. In the context menu, select [Adopting the configuration from a file].
6. Follow the instructions in the dialog.
8.19 Updating the Firmware
If no automatic update is set in the communication product (e.g. SMA Data Manager or
Sunny Home Manager) or in Sunny Portal, you have the option of carrying out a manual firmware
update.
You have the following options to update the firmware:
• Update the firmware with the existing update file via the user interface of the inverter.
• Search and install the firmware via the user interface of the inverter.
Update the firmware with the existing update file via the user interface of the
inverter.
Requirements:
☐ An update file with the desired inverter firmware must be available. The update file is, for
example, available for download on the product page of the inverter at www.SMA-Solar.com.
To download the update file, it is necessary to enter the serial number of the inverter.
Procedure:
1. Open the user interface (see Section 8.1, page 49).
2. Log into the user interface as an Installer (see Section 8.2, page 53).
3. Select the menu Device Configuration.
4. In the inverter row, click on the gear icon and select Update firmware.
5. Select [Browse] and select the update file for the inverter.
6. Select Update firmware.
7. Follow the instructions in the dialog.
Search and install the firmware via the user interface of the inverter.
Requirements:
☐ The inverter must be connected to the Internet.
Procedure:
1. Open the user interface (see Section 8.1, page 49).
2. Log into the user interface as an Installer (see Section 8.2, page 53).
3. Click on [Edit parameters].
4. Go to Device > Update.
Operating manual
STP3-6-3AV-40-BE-en-13
67
8 Operation
SMA Solar Technology AG
5. Select the parameter Check for update and install it and set it to Execute.
6. Click on [Save all].
☑ The firmware is updated in the background.
68
STP3-6-3AV-40-BE-en-13
Operating manual
9 Disconnecting the Inverter from Voltage Sources
SMA Solar Technology AG
9
Disconnecting the Inverter from Voltage Sources
Prior to performing any work on the inverter, always disconnect it from all voltage sources as
described in this section. Always adhere to the prescribed sequence.
WARNING
Danger to life due to electric shock from destruction of the measuring device
due to overvoltage
Overvoltage can damage a measuring device and result in voltage being present in the
enclosure of the measuring device. Touching the live enclosure of the measuring device results in
death or lethal injuries due to electric shock.
• Only use measuring devices with a DC input voltage range of 1000 V or higher.
Procedure:
1. Disconnect the AC circuit breaker and secure it against reconnection.
2. Set the DC load-break switch of the inverter to O.
3. Wait until the LEDs have gone out.
4. Use a current clamp to ensure that no current is
present in the DC cables.
$
B
Operating manual
STP3-6-3AV-40-BE-en-13
69
9 Disconnecting the Inverter from Voltage Sources
SMA Solar Technology AG
DANGER
5.
Danger to life due to electric shock when touching exposed DC
conductors or DC plug contacts if the DC connectors are damaged or
loose
The DC connectors can break or become damaged, become free of the DC cables, or no
longer be connected correctly if the DC connectors are released and disconnected
incorrectly. This can result in the DC conductors or DC plug contacts being exposed.
Touching live DC conductors or DC plug connectors will result in death or serious injury due
to electric shock.
• Wear insulated gloves and use insulated tools when working on the DC connectors.
• Ensure that the DC connectors are in perfect condition and that none of the DC
conductors or DC plug contacts are exposed.
• Carefully release and remove the DC connectors as described in the following.
6. Release and remove the DC connectors. To do so,
insert a flat-blade screwdriver or an angled
screwdriver (blade width: 3.5 mm) into one of the
side slots and pull the DC connectors out. When
doing so, do not lever the DC connectors out, but
insert the tool into one of the side slots only to
release the locking mechanism, and do not pull on
the cable.
7. Ensure that no voltage is present between the
positive terminal and negative terminal at the DC
inputs using a suitable measuring device.
B
B
9
8. Ensure that no voltage is present between the positive terminal and ground as well as between
the negative terminal and ground on the DC inputs using a suitable measuring device.
9. Unscrew the AC connector and pull it out of the jack
for the AC connection.
70
STP3-6-3AV-40-BE-en-13
Operating manual
10 Cleaning the Inverter
SMA Solar Technology AG
10 Cleaning the Inverter
NOTICE
Damage due to cleaning agents
The use of cleaning agents may cause damage to the product and its components.
• Clean the product and all its components only with a cloth moistened with clear water.
• Ensure that the inverter is free of dust, foliage and other dirt.
Operating manual
STP3-6-3AV-40-BE-en-13
71
11 Troubleshooting
SMA Solar Technology AG
11 Troubleshooting
11.1 Forgotten Password
If you have forgotten the password for the inverter, you can unlock the inverter with a Personal
Unlocking Key (PUK). For each inverter, there is one PUK for each user group (User and Installer).
Tipp: With PV systems that are registered in a communication product, you can also assign a new
password for the user group Installer via the communication product. The password for the user
group Installer is the same as the system password in the communication product.
Procedure:
1. Request PUK (application form available at www.SMA-Solar.com).
2. Open the user interface (see Section 8.1, page 49).
3. Enter the PUK instead of the password into the field Password.
4. Select Login.
5. Call up the menu Device Parameters.
6. Click on [Edit parameters].
7. In the parameter group User Rights > Access Control change the password of the desired
user group.
8. Select [Save all] to save the changes.
Password assignment for inverters that are registered in a communication
product
The password for the user group Installer is also the system password for the system in the
communication product. Changing the password of the user group Installer can lead to the
inverter no longer being able to be reached by the communication product.
• In the communication product, assign the changed password of the user group Installer
as the new system password (see the manual of the communication product).
72
STP3-6-3AV-40-BE-en-13
Operating manual
11 Troubleshooting
SMA Solar Technology AG
11.2 Event Messages
Event number
101
102
103
202
203
205
Operating manual
Message, cause and corrective measures
Grid fault
The grid voltage or grid impedance at the connection point of the inverter is
too high. The inverter has disconnected from the utility grid.
Corrective measures:
• Check whether the grid voltage at the connection point of the inverter is
permanently in the permissible range.
If the grid voltage is outside the permissible range due to local grid
conditions, contact the grid operator. The grid operator must agree with
an adjustment of the voltage at the feed-in point or with a change of the
monitored operating limits.
If the grid voltage is permanently within the permissible range and this
message is still displayed, contact Service.
Grid fault
The utility grid has been disconnected, the AC cable is damaged or the grid
voltage at the connection point of the inverter is too low. The inverter has disconnected from the utility grid.
Corrective measures:
• Ensure that the circuit breaker is switched on.
• Ensure that the AC cable is not damaged and that it is connected
correctly.
• Ensure that the country data set has been configured correctly.
• Check whether the grid voltage at the connection point of the inverter is
permanently in the permissible range.
If the grid voltage is outside the permissible range due to local grid
conditions, contact the grid operator. The grid operator must agree with
an adjustment of the voltage at the feed-in point or with a change of the
monitored operating limits.
If the grid voltage is permanently within the permissible range and this
message is still displayed, contact the Service.
STP3-6-3AV-40-BE-en-13
73
11 Troubleshooting
Event number
SMA Solar Technology AG
Message, cause and corrective measures
301
Grid fault
The ten-minute average value of the grid voltage is no longer within the permissible range. The grid voltage or grid impedance at the connection point is
too high. The inverter disconnects from the utility grid to maintain power quality.
Corrective measures:
• During the feed-in operation, check whether the grid voltage at the
connection point of the inverter is permanently in the permissible range.
If the grid voltage is outside the permissible range due to local grid
conditions, contact the grid operator. The grid operator must agree with
an adjustment of the voltage at the feed-in point or with a change of the
monitored operating limits.
If the grid voltage is permanently within the permissible range and this
message is still displayed, contact Service.
302
Active power limit AC voltage
The inverter has reduced its power due to a too-high grid voltage to ensure
grid stability.
Corrective measures:
• If possible, check the grid voltage and observe how often fluctuations
occur. If fluctuations occur frequently and this message is displayed often,
contact the grid operator and request approval to change the operating
parameters of the inverter. If the grid operator gives his approval, discuss
any changes to the operating parameters with the Service.
401
404
74
Grid fault
The inverter has disconnected from the utility grid. A stand-alone grid or a very
large change in the power frequency was detected.
Corrective measures:
• Check the grid connection for significant short-term frequency fluctuations.
STP3-6-3AV-40-BE-en-13
Operating manual
11 Troubleshooting
SMA Solar Technology AG
Event number
Message, cause and corrective measures
501
Grid fault
The power frequency is not within the permissible range. The inverter has disconnected from the utility grid.
Corrective measures:
• If possible, check the power frequency and observe how often
fluctuations occur.
If fluctuations occur frequently and this message is displayed often,
contact the grid operator and request approval to change the operating
parameters of the inverter.
If the grid operator gives his approval, discuss any changes to the
operating parameters with the Service.
601
Grid fault
The inverter has detected an excessively high proportion of direct current in
the grid current.
Corrective measures:
• Check the grid connection for direct current.
• If this message is displayed frequently, contact the grid operator and
check whether the monitoring threshold on the inverter can be raised.
701
Frequency not permitted > Check parameter
The power frequency is not within the permissible range. The inverter has disconnected from the utility grid.
Corrective measures:
• If possible, check the power frequency and observe how often
fluctuations occur.
If fluctuations occur frequently and this message is displayed often,
contact the grid operator and request approval to change the operating
parameters of the inverter.
If the grid operator gives his approval, discuss any changes to the
operating parameters with the Service.
Operating manual
STP3-6-3AV-40-BE-en-13
75
11 Troubleshooting
Event number
SMA Solar Technology AG
Message, cause and corrective measures
901
PE connection missing > Check connection
The grounding conductor is not correctly connected.
Corrective measures:
• Ensure that the grounding conductor is correctly connected.
1001
L / N swapped > Check connection
The connection of L and N is swapped.
Corrective measures:
• Ensure that L and N are correctly connected.
1101
Installation fault > Check connection
A second line conductor is connected to N.
Corrective measures:
• Connect the neutral conductor to N.
1302
Waiting for grid voltage > Installation failure grid connection > Check
grid and fuses
L or N not connected.
Corrective measures:
• Ensure that L and N are connected.
• Ensure that the circuit breaker is switched on.
• Ensure that the AC cable is not damaged and that it is connected
correctly.
1501
Reconnection fault grid
The changed country data set or the value of a parameter you have set does
not correspond to the local requirements. The inverter cannot connect to the
utility grid.
Corrective measures:
• Ensure that the country data set has been configured correctly. To do this,
select the parameter Set country standard and check the value.
76
STP3-6-3AV-40-BE-en-13
Operating manual
11 Troubleshooting
SMA Solar Technology AG
Event number
Message, cause and corrective measures
3301
3302
3303
Unstable operation
There is not enough power at the DC input of the inverter for stable operation.
The inverter cannot connect to the utility grid.
Corrective measures:
• Ensure that the PV array is designed correctly.
• Ensure that the PV array is not covered by snow or otherwise shaded.
• Ensure that the PV array is free of errors.
3401
3402
3407
DC overvoltage > Disconnect generator
Overvoltage at the DC input. This can destroy the inverter.
This message is signalized additionally by rapid flashing of the LEDs.
Corrective measures:
• Immediately disconnect the inverter from all voltage sources.
• Check whether the DC voltage is below the maximum input voltage of
the inverter. If the DC voltage is below the maximum input voltage of the
inverter, reconnect the DC connectors to the inverter.
• If the DC voltage exceeds the maximum input voltage of the inverter,
ensure that the PV array has been correctly rated or contact the installer
of the PV array.
• If this message is repeated frequently, contact the Service.
3501
Insulation failure > Check generator
The inverter has detected a ground fault in the PV array.
Corrective measures:
• Check the PV system for ground faults.
3701
Residual current too high > Check generator
The inverter has detected a residual current due to temporary grounding of the
PV array.
Corrective measures:
• Check the PV system for ground faults.
Operating manual
STP3-6-3AV-40-BE-en-13
77
11 Troubleshooting
Event number
3801
3802
3805
SMA Solar Technology AG
Message, cause and corrective measures
DC overcurrent > Check generator
Overcurrent at the DC input. The inverter briefly interrupts feed-in operation.
Corrective measures:
• If this message is displayed frequently, ensure that the PV array has been
correctly rated and wired.
3901
3902
Waiting for DC start conditions > Start conditions not met
The feed-in conditions for the utility grid are not yet fulfilled.
Corrective measures:
• Ensure that the PV array is not covered by snow or otherwise shaded.
• Wait for higher irradiation.
• If this message is displayed frequently in the morning, increase the
voltage limit for starting grid feed-in. Change the parameter Critical
voltage to start feed-in.
• If this message is displayed frequently with medium irradiation, ensure
that the PV array is correctly rated.
4011
Bridged strings determined
The DC inputs A and B are connected in parallel.
4012
No bridged strings determined
The DC inputs A and B are not connected in parallel.
6002-6412
Self-diagnosis > Interference device
The cause must be determined by the Service.
Corrective measures:
• Contact the Service.
78
STP3-6-3AV-40-BE-en-13
Operating manual
11 Troubleshooting
SMA Solar Technology AG
Event number
6501
6502
6509
6512
6602
6603
6604
6801
6802
6901
6902
6701
6702
Operating manual
Message, cause and corrective measures
Self-diagnosis > Overtemperature
The inverter has switched off due to excessive temperature.
Corrective measures:
• Clean the cooling fins on the rear of the enclosure and the air ducts on
the top using a soft brush.
• Ensure that the inverter has sufficient ventilation.
• Ensure that the ambient temperature does not exceed +40 °.
• Ensure that the inverter is not exposed to direct solar irradiation.
Minimum operating temperature not reached
The inverter will only recommence grid feed-in once the temperature has
reached at least −25°C.
Self-diagnosis > Overload
The cause must be determined by the Service.
Corrective measures:
• Contact the Service.
Self-diagnosis > Input A defective
Corrective measures:
• Check whether a string is connected to input A.
• Contact the service.
Self-diagnosis > Input B defective
Corrective measures:
• Check whether a string is connected to input B.
• Contact the service.
Communication disturbed
Error in the communication processor, the inverter continues feeding in, however. The cause must be determined by the Service.
Corrective measures:
• If this message is displayed frequently, contact the Service.
STP3-6-3AV-40-BE-en-13
79
11 Troubleshooting
Event number
SMA Solar Technology AG
Message, cause and corrective measures
7102
Parameter file not found or defective
The parameter file was not found or is defective. The update failed. The inverter continues to feed in.
Corrective measures:
• Copy the parameter file to the correct folder again.
7105
Parameter setting failed
Parameters could not be set using the memory card. The inverter continues to
feed in.
Corrective measures:
• Ensure that the parameters are set correctly.
• Ensure that the SMA Grid Guard code is available.
7106
Update file defective
The update file is defective. The update failed. The inverter continues to feed
in.
7110
No update file found
No new update file was found on the SD memory card. The update failed.
The inverter continues to feed in.
7112
Update file successfully copied
7113
The memory card is full or write-protected
7201 to 7202
Data storage not possible
7303
Update main CPU failed
The cause must be determined by the Service.
Corrective measures:
• Contact the Service.
7320
The device was successfully updated
The firmware update was completed successfully.
7330
Condition test failed
The testing of the update conditions was successful. The firmware update
package is suitable for this inverter.
7331
Update transport started
Update file is being copied.
80
STP3-6-3AV-40-BE-en-13
Operating manual
11 Troubleshooting
SMA Solar Technology AG
Event number
Message, cause and corrective measures
7332
Update transport successful
Update file was copied successfully to the inverter's internal memory.
7333
Update transport failed
Update file could not be copied to the inverter's internal memory. In the event
of connection with the inverter via WLAN, a poor connection quality can be
the cause.
Corrective measures:
• Retry update.
• For WLAN connection: Improve the WLAN connection quality (e.g., via
WLAN repeater) or establish connection with the inverter via Ethernet.
• If this message is displayed again, contact the Service.
7341
Update Bootloader
The inverter is performing a bootloader update.
7342
Update Bootloader failed
The bootloader update failed.
Corrective measures:
• Retry update.
• If this message is displayed again, contact the Service.
7347
Incompatible file
The configuration file is not suitable for this inverter.
Corrective measures:
• Ensure that the selected configuration file is suitable for this inverter.
• Retry import.
7348
Incorrect file format
The configuration file is not of the required format or is damaged.
Corrective measures:
• Ensure that the selected configuration file is of the required format and is
not damaged.
• Retry import.
Operating manual
STP3-6-3AV-40-BE-en-13
81
11 Troubleshooting
SMA Solar Technology AG
Event number
Message, cause and corrective measures
7349
Incorrect login rights for configuration file
The user group logged in does not have the user rights necessary to be able
to import a configuration.
Corrective measures:
• Log in as Installer.
• Import configuration file again.
7350
Transfer of a configuration file has started
The configuration file is being transferred.
7351
Update WLAN
The inverter is updating the WLAN module.
7352
Update of WLAN not successful
The update of the WLAN module failed.
Corrective measures:
• Retry update.
• If this message is displayed again, contact the Service.
7353
Update time zone database
The inverter is updating the time zone database.
7354
Update of time zone database not successful
The update of the time zone database failed.
Corrective measures:
• Retry update.
• If this message is displayed again, contact the Service.
7355
Update WebUI
The inverter is updating the inverter user interface.
7356
Update of the WebUI not successful
The update of the inverter user interface failed.
Corrective measures:
• Retry update.
• If this message is displayed again, contact the Service.
82
STP3-6-3AV-40-BE-en-13
Operating manual
11 Troubleshooting
SMA Solar Technology AG
Event number
Message, cause and corrective measures
7500 to 7501
Fan fault > Check inverter electr. and fan
Corrective measures:
• Contact the Service.
7619
Communication fault with meter unit > Check communication to meter
The inverter is not receiving any data from the energy meter.
Corrective measures:
• Ensure that the energy meter is correctly integrated into the same network
as the inverter (see energy meter manual).
• For WLAN connection: Improve the WLAN connection quality (e.g., via
WLAN repeater) or connect the inverter with the DHCP server (router) via
Ethernet.
7702
Interference device
The cause must be determined by the Service.
Corrective measures:
• Contact the Service.
8003
Active power limit Temperature
The inverter has reduced its power output for more than ten minutes due to excessive temperature.
Corrective measures:
• Clean the cooling fins on the rear of the enclosure and the air ducts on
the top using a soft brush.
• Ensure that the inverter has sufficient ventilation.
• Ensure that the ambient temperature does not exceed +40 °.
• Ensure that the inverter is not exposed to direct solar irradiation.
8101 to 8104
Communication disturbed
The cause must be determined by the Service.
Corrective measures:
• Contact the Service.
Operating manual
STP3-6-3AV-40-BE-en-13
83
11 Troubleshooting
Event number
SMA Solar Technology AG
Message, cause and corrective measures
9002
SMA Grid Guard code invalid
The SMA Grid Guard code entered is incorrect. The operating parameters are
still protected and cannot be changed.
Corrective measures:
• Enter the correct SMA Grid Guard code.
9003
Grid parameter locked
Changes to the grid parameters are now blocked. In order to be able to make
changes to the grid parameters, from now on you must log in using the SMA
Grid Guard code.
9005
Changing of grid parameters not possible > Ensure DC supply
This error can have the following causes:
• The parameters to be changed are protected.
• The DC voltage at the DC input is not sufficient to run the main CPU.
Corrective measures:
• Enter the SMA Grid Guard code.
• Ensure that at least the DC start voltage is available (green LED is
flashing, pulsing or glowing).
9007
Abort self-test
The self-test (Italy only) was terminated.
Corrective measures:
• Ensure that the AC connection is correct.
• Restart the self-test.
10108
Time adjusted / old time
10109
Time adjusted / new time
10110
Time synchronization failed: |tn0|
No time information could be called up from the set NTP server.
Corrective measures:
• Ensure that the NTP server was configured correctly.
• Ensure that the inverter is integrated into a local network with Internet
connection.
84
STP3-6-3AV-40-BE-en-13
Operating manual
11 Troubleshooting
SMA Solar Technology AG
Event number
Message, cause and corrective measures
10118
Parameter upload complete
The configuration file was loaded successfully.
10248
[Interface]: network busy
The network is busy. Data exchange between the devices is not at an optimum
and is greatly delayed.
Corrective measures:
• Increase the query intervals.
• If necessary, reduce the number of devices in the network.
10249
[Interface]: network overloaded
The network is overloaded. There is no data exchange between the devices.
Corrective measures:
• Reduce the number of devices in the network.
• If necessary, increase the data query intervals.
10250
[Interface]: package error rate [ok / high]
The package error rate has changed. If the package error rate is high, the network is overloaded or the connection to the network switch or DHCP server
(router) is disturbed.
Corrective measures if the package error rate is high:
• Ensure that with an Ethernet connection, the network cable and the
network connector are not damaged and that the network connectors are
correctly plugged.
• If necessary, increase the data query intervals.
• If necessary, reduce the number of devices in the network.
10251
Operating manual
[Interface]: communication status goes to [OK / Warning / Error /
Not connected]
The communication status to the network switch or DHCP server (router) has
changed. An additional error message may be displayed.
STP3-6-3AV-40-BE-en-13
85
11 Troubleshooting
Event number
SMA Solar Technology AG
Message, cause and corrective measures
10252
[Interface]: communication disrupted
There is no valid signal on the network line.
Corrective measures:
• Ensure that with an Ethernet connection, the network cable and the
network connector are not damaged and that the network connectors are
correctly plugged.
• Ensure that the DHCP server (router) and any network switches are
signalizing correct operation.
10253
[Interface]: connection speed goes to [100 Mbit / 10 Mbit]
The data transfer rate has changed. The cause for the status [10 Mbit] can be
a defective plug, a defective cable or the pulling or plugging of the network
connector.
Corrective measures if the status is [10 Mbit]:
• Ensure that with an Ethernet connection, the network cable and the
network connector are not damaged and that the network connectors are
correctly plugged.
• Ensure that the DHCP server (router) and any network switches are
signalizing correct operation.
10254
[Interface]: duplex mode goes to [Full / Half]
The duplex mode (data transfer mode) has changed. The cause for the status
[Half] can be a defective plug, a defective cable or the pulling or plugging of
the network connector.
Corrective measures if the status is [Half]:
• Ensure that with an Ethernet connection, the network cable and the
network connector are not damaged and that the network connectors are
correctly plugged.
• Ensure that the DHCP server (router) and any network switches are
signalizing correct operation.
10255
[Interface]: Network load OK
The network load has returned to a normal range after being busy.
86
STP3-6-3AV-40-BE-en-13
Operating manual
11 Troubleshooting
SMA Solar Technology AG
Event number
Message, cause and corrective measures
10282
[User group]-Login via [protocol] locked
After several incorrect login attempts, login has been blocked for a limited
time. In this case, the User login will be blocked for 15 minutes, the
Grid Guard login for 12 hours.
Corrective measures:
• Wait until the given time has expired and then retry login.
10283
WLAN module faulty
The WLAN module integrated in the inverter is defective.
Corrective measures:
• Contact the Service.
10284
No WLAN connection possible
The inverter does not currently have a WLAN connection to the selected network.
Corrective measures:
• Ensure that the SSID, the WLAN password and the encryption method
have been entered correctly. The encryption method is specified by your
WLAN router or WLAN Access Point and can be changed there.
• Ensure that the WLAN router or WLAN Access Point is in range and is
signalizing correct operation.
• If this message is displayed often, improve the WLAN connection by
using a WLAN repeater.
10285
WLAN connection established
Connection to the selected WLAN network has been established.
10286
WLAN connection lost
The inverter has lost WLAN connection to the selected network.
Corrective measures:
• Ensure that the WLAN router or WLAN Access Point is still active.
• Ensure that the WLAN router or WLAN Access Point is in range and is
signalizing correct operation.
• If this message is displayed often, improve the WLAN connection by
using a WLAN repeater.
10339
Operating manual
Webconnect enabled
The Webconnect function has been enabled.
STP3-6-3AV-40-BE-en-13
87
11 Troubleshooting
SMA Solar Technology AG
Event number
Message, cause and corrective measures
10340
Webconnect disabled
The Webconnect function has been disabled.
10502
Active power limit AC frequency
The inverter has reduced its power due to a too-high power frequency to ensure grid stability.
Corrective measures:
• If possible, check the power frequency and observe how often
fluctuations occur. If fluctuations occur frequently and this message is
displayed often, contact the grid operator and request approval to
change the operating parameters of the inverter. If the grid operator
gives his approval, discuss any changes to the operating parameters with
the Service.
10901
Self-test start [xx]
The self-test is running.
10902
Current disconnection limit for voltage increase protection [xxx] V
Preliminary result of the self-test
10903
Current disconnection limit for voltage monitoring lower maximum
threshold [xxx] V
Preliminary result of the self-test
10904
Current disconnection limit for voltage monitoring upper minimum
threshold [xxx] V
Preliminary result of the self-test
10905
Current disconnection limit for voltage monitoring middle minimum
threshold [xxx] V
Preliminary result of the self-test
10906
Current disconnection limit for frequency monitoring switchable maximum threshold |xxx| Hz
Preliminary result of the self-test
10907
Current disconnection limit for frequency monitoring switchable minimum threshold [xxx] Hz
Preliminary result of the self-test
10908
Current disconnection limit for frequency monitoring switchable minimum threshold [xxx] Hz
Preliminary result of the self-test
10909
Current disconnection limit for frequency monitoring upper minimum
threshold [xxx] Hz
Preliminary result of the self-test
88
STP3-6-3AV-40-BE-en-13
Operating manual
11 Troubleshooting
SMA Solar Technology AG
Event number
Message, cause and corrective measures
10910
Measured disconnection threshold for the running test point [xxx]
[xx]
Preliminary result of the self-test
10911
Measured disconnection threshold for the running test point [xxx]
[xx]
Preliminary result of the self-test
10912
Measured disconnection time for the running test point [xx] s
Preliminary result of the self-test
27103
Set parameter
The parameter changes are being adopted.
27104
Parameters set successfully
The parameter changes were successfully adopted.
27107
Update file OK
The update file found is valid.
27301
Update communication
The inverter is updating the communication component.
27302
Update main CPU
The inverter is updating the inverter component.
27312
Update completed
The inverter has successfully completed the update.
29001
Installer code valid
The entered Grid Guard code is valid. Protected parameters have now been
unlocked and you can adjust the parameters. The parameters will be automatically locked again after ten feed-in hours.
29004
Grid parameters unchanged
Changing the grid parameters is not possible.
11.3 Checking the PV System for Ground Faults
If the red LED is glowing and the event number 3501, 3601 or 3701 is being displayed in the
Results menu on the inverter user interface, there may be a ground fault present. The electrical
insulation from the PV system to ground is defective or insufficient.
Operating manual
STP3-6-3AV-40-BE-en-13
89
11 Troubleshooting
SMA Solar Technology AG
DANGER
Danger to life due to electric shock when touching live system components in
case of a ground fault
If a ground fault occurs, parts of the system may still be live. Touching live parts and cables
results in death or lethal injuries due to electric shock.
• Disconnect the product from voltage sources and make sure it cannot be reconnected
before working on the device.
• Touch the cables of the PV array on the insulation only.
• Do not touch any parts of the substructure or frame of the PV array.
• Do not connect PV strings with ground faults to the inverter.
WARNING
Danger to life due to electric shock from destruction of the measuring device
due to overvoltage
Overvoltage can damage a measuring device and result in voltage being present in the
enclosure of the measuring device. Touching the live enclosure of the measuring device results in
death or lethal injuries due to electric shock.
• Only use measuring devices with a DC input voltage range of 1000 V or higher.
Procedure:
In order to check the PV system for ground faults, perform the following actions in the prescribed
order. The exact procedure is described in the following sections.
• Check the PV system for ground faults by measuring the voltage.
• If the voltage measurement was not successful, check the PV system via insulation resistance
measurement for ground faults.
Test by Measuring the Voltage
Proceed as follows to check each string in the PV system for ground faults.
Procedure:
DANGER
1.
Danger to life due to high voltages
• Disconnect the inverter from all voltage sources (see Section 9, page 69).
2. Measure the voltages:
• Measure the voltage between the positive terminal and the ground potential (PE).
• Measure the voltage between the negative terminal and the ground potential (PE).
90
STP3-6-3AV-40-BE-en-13
Operating manual
11 Troubleshooting
SMA Solar Technology AG
• Measure the voltage between the positive and negative terminals.
If the following results are present at the same time, there is a ground fault in the PV
system:
☑ All measured voltages are stable.
☑ The sum of the two voltages to ground potential is approximately equal to the
voltage between the positive and negative terminals.
3. If a ground fault is present, determine the location of the ground fault via the ratio of the two
measured voltages and eliminate the ground fault.
4. If a definite ground fault cannot be measured and the message is still displayed, measure the
insulation resistance.
5. Reconnect the strings without ground faults to the inverter and recommission the inverter (see
inverter installation inverter).
Location of the ground fault
The example shows a ground fault between the second and third PV module.
V1 = 200 V
100 V
V2 = 300 V
100 V
100 V
100 V
100 V
+
Test by Measuring the Insulation Resistance
If the voltage measurement does not provide sufficient evidence of a ground fault, the insulation
resistance measurement can provide more exact results.
Operating manual
STP3-6-3AV-40-BE-en-13
91
11 Troubleshooting
SMA Solar Technology AG
+
Figure 15: Schematic diagram of the measurement
Calculating the insulation resistance
The expected total resistance of the PV system or of an individual string can be calculated
using the following formula:
total
The exact insulation resistance of a PV module can be obtained from the module manufacturer
or the datasheet.
For the resistance of a PV module an average value can be assumed: for thin-film PV modules
approximately 40 MOhm and for polycrystalline and monocrystalline PV modules
approximately 50 MOhm per PV module (for further information on calculating the insulation
resistance see the Technical Information "Insulation Resistance (Riso) of Non-Galvanically
Isolated PV Systems" at www.SMA-Solar.com).
Required devices:
☐ Suitable device for safe disconnection and short-circuiting
☐ Measuring device for insulation resistance
Device required for safe disconnection and short-circuiting of the PV array
The insulation resistance can only be measured with a suitable device for safe disconnection
and short-circuiting of the PV array. If no suitable device is available, the insulation
measurement must not be carried out.
Procedure:
1. Calculate the expected insulation resistance per string.
DANGER
2.
Danger to life due to high voltages
• Disconnect the inverter from all voltage sources (see Section 9, page 69).
3. Install the short circuit device.
4. Connect the measuring device for insulation resistance.
5. Short-circuit the first string.
92
STP3-6-3AV-40-BE-en-13
Operating manual
SMA Solar Technology AG
11 Troubleshooting
6. Set the test voltage. The test voltage should be as close as possible to the maximum system
voltage of the PV modules but must not exceed it (see datasheet of the PV modules).
7. Measure the insulation resistance.
8. Eliminate the short circuit.
9. Measure the remaining strings in the same manner.
☑ If the insulation resistance of a string deviates considerably from the theoretically
calculated value, there is a ground fault present in that string.
10. Reconnect to the inverter only those strings from which the ground fault has been eliminated.
11. Reconnect all other strings to the inverter.
12. Recommission the inverter.
13. If the inverter still displays an insulation error, contact the Service (see Section 14, page 103).
The PV modules might not be suitable for the inverter in the present quantity.
11.4 Problems with streaming services
If you use the streaming service in your local network (in which the inverter is also included), there
may be interference to the transfer of data. In this case, the IGMP settings of the inverter can be
changed via operating parameters.
• Contact the Service and change IGMP settings in consultation with the Service department.
Operating manual
STP3-6-3AV-40-BE-en-13
93
12 Decommissioning the Inverter
SMA Solar Technology AG
12 Decommissioning the Inverter
To decommission the inverter completely upon completion of its service life, proceed as described
in this Section.
CAUTION
Risk of injury due to weight of product
Injuries may result if the product is lifted incorrectly or dropped while being transported or
mounted.
• Transport and lift the product carefully. Take the weight of the product into account.
• Wear suitable personal protective equipment for all work on the product.
Procedure:
DANGER
1.
Danger to life due to high voltages
• Disconnect the inverter from all voltage sources (see Section 9, page 69).
CAUTION
2.
Risk of burns due to hot enclosure parts
• Wait 30 minutes for the enclosure to cool down.
3. Unscrew the RS485 plug and pull it out of the jack.
56
4. Screw the protective cap onto the RS485 jack.
5. Unscrew the swivel nut from the threaded sleeve for
the network cable.
56
94
STP3-6-3AV-40-BE-en-13
Operating manual
SMA Solar Technology AG
6. Unscrew and remove the threaded sleeve from the
network port thread on the inverter.
12 Decommissioning the Inverter
7. Release the network cable plug and pull it out of the
jack on the inverter.
8. Take the cable support sleeve out of the threaded
sleeve and remove the network cable from the cable
support sleeve.
9. Lead the network cable out of the threaded sleeve
and the swivel nut.
10. Screw the protective cap onto the network port.
11. Unscrew and remove the antenna.
Operating manual
STP3-6-3AV-40-BE-en-13
95
12 Decommissioning the Inverter
SMA Solar Technology AG
12. If there is a protective cap available, plug the
protective cap onto the jack for connecting the
antenna.
13. If an additional grounding or an equipotential
bonding is connected to the inverter, unscrew the
pan head screw M5x12 (TX25) and remove the
grounding cable.
14. Unscrew the left- and right-hand pan head screws
M5x12 used to secure the inverter to the wall
mounting bracket (TX25).
15. Remove the inverter by lifting it vertically up and off
the wall mounting bracket.
16. Unscrew the screws for fastening the wall mounting
bracket and remove the wall mounting bracket.
83
17. If the inverter is to be stored or shipped, pack the inverter, the AC connector, the DC
connector, the RJ45 protective sleeve, the antenna and the wall mounting bracket. Use the
original packaging or packaging that is suitable for the weight and dimensions of the inverter.
18. Dispose of the inverter in accordance with the locally applicable disposal regulations for
electronic waste.
96
STP3-6-3AV-40-BE-en-13
Operating manual
13 Technical Data
SMA Solar Technology AG
13 Technical Data
13.1 DC/AC
13.1.1 Sunny Tripower 3.0 / 4.0
DC input
STP3.0-3AV-40
STP4.0-3AV-40
Maximum PV array power
6000 Wp
8000 Wp
Maximum input voltage
850 V
850 V
MPP voltage range
140 V to 800 V
175 V to 800 V
Rated input voltage
580 V
580 V
Minimum input voltage
125 V
125 V
Initial input voltage
175 V
175 V
Maximum input current, input A
12 A
12 A
Maximum input current, input B
12 A
12 A
Maximum short-circuit current,
input A*
18 A
18 A
Maximum short-circuit current,
input B*
18 A
18 A
Maximum reverse current into
the PV array
0A
0A
Number of independent MPP
inputs
2
2
Strings per MPP input
1
1
Surge category in accordance
with IEC 60664-1
II
II
* In accordance with IEC 62109-2: ISC PV
AC Output
STP3.0-3AV-40
STP4.0-3AV-40
Rated power at 230 V, 50 Hz
3000 W
4000 W
Maximum apparent AC power at cos φ = 1
3000 VA
4000 VA
Rated grid voltage
230 V
230 V
Nominal AC voltage
Operating manual
3/N/PE, 220 V /
3/N/PE, 220 V /
380 V, 230 V /
380 V, 230 V /
400 V, 240 V / 415 V 400 V, 240 V / 415 V
STP3-6-3AV-40-BE-en-13
97
13 Technical Data
SMA Solar Technology AG
AC voltage range*
STP3.0-3AV-40
STP4.0-3AV-40
180 V to 280 V
180 V to 280 V
Nominal AC current at 220 V
3 x 4.6 A
3 x 6.1 A
Nominal AC current at 230 V
3 x 4.4 A
3 x 5.8 A
Nominal AC current at 240 V
3 x 4.2 A
3 x 5.6 A
Maximum output current
3 x 4.6 A
3 x 6.1 A
Total harmonic distortion of the output current
with total harmonic distortion of the AC voltage
<2%, and AC power >50% of the rated power
< 3%
< 3%
Maximum output current under fault conditions
13 A
15 A
< 20% of the nominal
AC current for a
maximum of 10 ms
< 20% of the nominal
AC current for a
maximum of 10 ms
Rated power frequency
50 Hz
50 Hz
AC power frequency*
50 Hz / 60 Hz
50 Hz / 60 Hz
Operating range at AC power frequency 50 Hz
45 Hz to 55 Hz
45 Hz to 55 Hz
Operating range at AC power frequency 60 Hz
55 Hz to 65 Hz
55 Hz to 65 Hz
1
1
Inrush current
Power factor at rated power
Displacement power factor cos φ, adjustable
0.8 overexcited to 0.8 0.8 overexcited to 0.8
underexcited
underexcited
Feed-in phases
3
3
Phase connection
3
3
Surge category in accordance with
IEC 60664-1
III
III
STP3.0-3AV-40
STP4.0-3AV-40
Maximum efficiency, ηmax
98.2%
98.2%
European weighted efficiency, ηEU
96.5%
97.1%
* Depending on the configured country data set
Efficiency
13.1.2 Sunny Tripower 5.0 / 6.0
STP5.0-3AV-40
STP6.0-3AV-40
Maximum PV array power
9000 Wp
9000 Wp
Maximum input voltage
850 V
850 V
98
STP3-6-3AV-40-BE-en-13
Operating manual
13 Technical Data
SMA Solar Technology AG
STP5.0-3AV-40
STP6.0-3AV-40
MPP voltage range
215 V to 800 V
260 V to 800 V
Rated input voltage
580 V
580 V
Minimum input voltage
125 V
125 V
Initial input voltage
175 V
175 V
Maximum input current, input A
12 A
12 A
Maximum input current, input B
12 A
12 A
Maximum short-circuit current,
input A*
18 A
18 A
Maximum short-circuit current,
input B*
18 A
18 A
Maximum reverse current into
the PV array
0A
0A
Number of independent MPP
inputs
2
2
Strings per MPP input
1
1
Surge category in accordance
with IEC 60664-1
II
II
* In accordance with IEC 62109-2: ISC PV
AC Output
STP5.0-3AV-40
STP6.0-3AV-40
Rated power at 230 V, 50 Hz
5000 W
6000 W
Maximum apparent AC power at cos φ = 1
5000 VA
6000 VA
230 V
230 V
Rated grid voltage
Nominal AC voltage
AC voltage range*
3/N/PE, 220 V /
3/N/PE, 220 V /
380 V, 230 V /
380 V, 230 V /
400 V, 240 V / 415 V 400 V, 240 V / 415 V
180 V to 280 V
180 V to 280 V
Nominal AC current at 220 V
3 x 7.6 A
3 x 9.1 A
Nominal AC current at 230 V
3 x 7.3 A
3 x 8.7 A
Nominal AC current at 240 V
3 x 7.0 A
3 x 8.4 A
Maximum output current
3 x 7.6 A
3 x 9.1 A
< 3%
< 3%
Total harmonic distortion of the output current
with total harmonic distortion of the AC voltage
<2%, and AC power >50% of the rated power
Operating manual
STP3-6-3AV-40-BE-en-13
99
13 Technical Data
SMA Solar Technology AG
STP5.0-3AV-40
Maximum output current under fault conditions
Inrush current
STP6.0-3AV-40
18 A
21 A
< 20% of the nominal
AC current for a
maximum of 10 ms
< 20% of the nominal
AC current for a
maximum of 10 ms
Rated power frequency
50 Hz
50 Hz
AC power frequency*
50 Hz / 60 Hz
50 Hz / 60 Hz
Operating range at AC power frequency 50 Hz
45 Hz to 55 Hz
45 Hz to 55 Hz
Operating range at AC power frequency 60 Hz
55 Hz to 65 Hz
55 Hz to 65 Hz
1
1
Power factor at rated power
Displacement power factor cos φ, adjustable
0.8 overexcited to 0.8 0.8 overexcited to 0.8
underexcited
underexcited
Feed-in phases
3
3
Phase connection
3
3
Surge category in accordance with
IEC 60664-1
III
III
* Depending on the configured country data set
Efficiency
STP5.0-3AV-40
STP6.0-3AV-40
Maximum efficiency, ηmax
98.2%
98.2%
European weighted efficiency, ηEU
97.4%
97.6%
13.2 General Data
Width x height x depth
Weight
435 mm x 470 mm x 176 mm
17.5 kg
Length x width x height of the packaging
495 mm x 595 mm x 250 mm
Transport weight
21.8 kg
Climatic category in accordance with
IEC 60721-3-4
4K4H
Environmental category
Outdoors
Pollution degree outside the enclosure
3
Pollution degree inside the enclosure
2
Operating temperature range
100
STP3-6-3AV-40-BE-en-13
-25°C to +60°C
Operating manual
13 Technical Data
SMA Solar Technology AG
Maximum permissible value for relative humidity
(condensing)
100%
Maximum operating altitude above mean sea
level (MSL)
3000 m
Typical noise emission
25 dB(A)
Power loss in night mode
5W
Maximum data volume per inverter with Speedwire/Webconnect
550 MB/month
Additional data volume when using the
Sunny Portal live interface
660 kB/hour
Topology
Transformerless
Cooling method
Convection
Degree of protection for electronics in accordance with IEC 60529
IP65
Protection class in accordance with
IEC 62109-1
Grid configurations*
I
IT, Delta-IT, TN-C, TN-S, TN-C-S, TT (when VN_PE
< 20 V)
* IT, Delta-IT: When using in these systems, the grounding conductor monitoring must be deactivated
and an additional grounding connected to the inverter.
13.3 Climatic Conditions
Installation in accordance with IEC 60721-3-3, Class 4K4H
Extended temperature range
-25°C to +60°C
Extended humidity range
0% to 100%
Extended air pressure range
79.5 kPa to 106 kPa
Transport in accordance with IEC 60721-3-2, Class 2K3
Temperature range
-25°C to +70°C
13.4 Protective Devices
DC reverse polarity protection
Short-circuit diode
Input-side disconnection point
DC Load-Break Switch
AC short-circuit current capability
Current control
Grid monitoring
Maximum overcurrent protection
Operating manual
SMA Grid Guard 10.0
32 A
STP3-6-3AV-40-BE-en-13
101
13 Technical Data
Ground fault monitoring
All-pole sensitive residual-current monitoring unit
SMA Solar Technology AG
Insulation monitoring: Riso > 200 kΩ
Available
13.5 Equipment
DC connection
SUNCLIX DC connector
AC connection
AC connector
WLAN
As standard
SMA Speedwire/Webconnect
As standard
RS485
As standard
13.6 Torques
Screws for securing the inverter to the wall
mounting bracket
2.5 Nm
Additional grounding
2.5 Nm
SUNCLIX swivel nut
2.0 Nm
13.7 Data Storage Capacity
Energy yields in the course of the day
63 days
Daily yields
30 years
Event messages for users
1024 events
Event messages for installers
1024 events
102
STP3-6-3AV-40-BE-en-13
Operating manual
14 Contact
SMA Solar Technology AG
14 Contact
If you have technical problems with our products, please contact the SMA Service Line. The
following data is required in order to provide you with the necessary assistance:
• Device type
• Serial number
• Firmware version
• Event message
• Mounting location and mounting height
• Type and number of PV modules
• Optional equipment, e.g. communication products
• Use the name of the system in Sunny Portal (if available)
• Access data for Sunny Portal (if available)
• Special country-specific settings (if available)
Deutschland SMA Solar Technology AG
Österreich Niestetal
Schweiz
Sunny Boy, Sunny Mini Central,
Sunny Tripower, Sunny Highpower: +49 561 9522‑1499
Monitoring Systems
(Kommunikationsprodukte):
+49 561 9522‑2499
Hybrid Controller:
+49 561 9522-3199
Sunny Island, Sunny Boy Storage, Sunny Backup:
+49 561 9522-399
Sunny Central, Sunny Central
Storage:
+49 561 9522-299
SMA Online Service Center:
www.SMA-Service.com
Belgien
Belgique
België
Luxemburg
Luxembourg
Nederland
Türkiye
SMA Service Partner DEKOM
Ltd. Şti.
+90 24 22430605
SMA Online Service Center:
www.SMA-Service.com
France
Ελλάδα
Κύπρος
SMA Service Partner AKTOR
FM.
Αθήνα
+30 210 8184550
SMA Online Service Center:
www.SMA-Service.com
SMA France S.A.S.
Lyon
+33 472 22 97 00
SMA Online Service Center :
www.SMA-Service.com
Operating manual
SMA Benelux BVBA/SPRL
Mechelen
+32 15 286 730
for Netherlands: +31 30 2492
000
SMA Online Service Center:
www.SMA-Service.com
Česko
SMA Service Partner TERMS
Magyarország a.s.
+420 387 6 85 111
Slovensko
SMA Online Service Center:
www.SMA-Service.com
STP3-6-3AV-40-BE-en-13
103
14 Contact
SMA Solar Technology AG
España
Portugal
SMA Ibérica Tecnología Solar,
S.L.U.
Barcelona
+34 935 63 50 99
SMA Online Service Center:
www.SMA-Service.com
United Kingdom
SMA Solar UK Ltd.
Milton Keynes
+44 1908 304899
SMA Online Service Center:
www.SMA-Service.com
Italia
SMA Italia S.r.l.
Milano
+39 02 8934-7299
SMA Online Service Center:
www.SMA-Service.com
Australia
SMA Australia Pty Ltd.
Sydney
Toll free for Australia:
1800 SMA AUS
(1800 762 287)
International:
+61 2 9491 4200
India
SMA Solar India Pvt. Ltd.
Mumbai
+91 22 61713888
대한민국
SMA Technology Korea Co.,
Ltd.
서울
+82-2-520-2666
United Arab SMA Middle East LLC
Emirates
Abu Dhabi
+971 2234 6177
SMA Online Service Center:
www.SMA-Service.com
ไทย
SMA Solar (Thailand) Co., Ltd.
กรุงเทพฯ
+66 2 670 6999
South Africa SMA Solar Technology South
Argentina
Africa Pty Ltd.
Brasil
Cape Town
Chile
08600SUNNY (08600 78669) Perú
International: +27 (0)21 826
0699
SMA Online Service Center:
www.SMA-Service.com
SMA South America SPA
Santiago de Chile
+562 2820 2101
Other coun- International SMA Service Line
tries
Niestetal
00800 SMA SERVICE
(+800 762 7378423)
SMA Online Service Center:
www.SMA-Service.com
104
STP3-6-3AV-40-BE-en-13
Operating manual
SMA Solar Technology AG
15 EU Declaration of Conformity
15 EU Declaration of Conformity
within the scope of the EU directives
• Electromagnetic compatibility 2014/30/EU (29.3.2014 L 96/79-106)
(EMC)
• Low Voltage Directive 2014/35/EU (29.3.2014 L 96/357-374) (LVD)
• Radio Equipment Directive 2014/53/EU (22.5.2014 L 153/62) (RED)
• Restriction of the use of certain hazardous substances 2011/65/EU
(L 174/88, June 8, 2011) and 2015/863/EU (L 137/10, March 31,
2015) (RoHS)
SMA Solar Technology AG confirms herewith that the products described in this document are in
compliance with the fundamental requirements and other relevant provisions of the abovementioned directives. The entire EU Declaration of Conformity can be found at www.SMASolar.com.
Operating manual
STP3-6-3AV-40-BE-en-13
105
www.SMA-Solar.com
">