MicroBT Whats Miner M3 Operation Instruction Manual

Whats Miner All-in-one machine
operation instruction
(Lite version)
V1.2(H3 platform)
Shenzhen MicroBT Electronics Technology Co., Ltd.
1
目录
1. Introduction of M3 Integrated Machine.......................................................................................3
2.Mine wiring, safety warning for operation on the shelf................................................................3
2.1.Matters needing attention in connection of Mine Machine.............................................. 3
2.1.1.Points for attention in connection of Control Panel 12V Power Line......................4
2.1.2.Matters needing attention in connection of Power supply Control Line................ 4
2.1.3.Matters needing attention in connection of Fan Line............................................. 5
2.1.4.Matters needing attention in data wiring connection of Force Plate..................... 6
2.1.5.Matters needing attention in connection of 12V Power Line with Power Plate.....6
2.1.6.Machine wiring inspection.......................................................................................7
2.2.Mining machine handling, on the shelf operation points for attention.............................7
3. Mine machine configuration environment preparation...............................................................8
3.1.Mine machine configuration equipment list...................................................................... 8
3.2.Mining machine network environment.............................................................................. 8
4.Mine machine connection and check before power on................................................................ 9
5.Mine data configuration (configured on the web page)............................................................. 10
5.1.Query dynamic ip address obtained by mining machine................................................. 10
5.1.1.Running WhatsMinerTools Software.....................................................................10
5.1.2.Query the ip address reported by the mine machine........................................... 10
5.2.Mine Pool & Miner data and configuration NTP Server address..................................... 12
5.2.1.Mine Pool & miner disposition.............................................................................. 12
5.2.2.Modify the address of the ntp synchronization server (optional).........................14
5.3. Configure mine machine static IP address (optional)...................................................... 15
5.4. English and Chinese language switching of Mining Machine Page................................. 17
6.Mine machine running condition check...................................................................................... 17
7.Batch data configuration, status check, firmware upgrade........................................................ 19
8.Disassembly and installation of integrated machine.................................................19
8.1. Disassembly and installation of Power supply.................................................................19
8.1.1.Power disassembly machine..................................................................................19
8.1.2.Installation of power supply.................................................................................. 23
8.2.Disassembly and installation of Control Panel..................................................................24
8.2.1.Disassembly of control panel.................................................................................24
8.2.2.Installation of control panel...................................................................................25
8.3.Disassembly and installation of Force Plate..................................................................... 26
8.3.1.Disassembly of force plate.....................................................................................26
8.3.2.Installation of force plate.......................................................................................29
2
1. Introduction of M3 Integrated Machine
Whatsminer M3 integrated machine
Bitcoin miner
The product parameters are as follows:
Computational power: 12TH/S
Chip: 189 28nm ASIC
Power consumption: 0.18~0.19kw/TH
Supporting Power supply: Shenma Power supply P5 (220vU 2250W)
Control board: with ambient
temperature: -5 ℃ ~ 40 ℃ whole
machine size: 375mm*130mm*225mm
2.Mine wiring, safety warning for operation on
the shelf
2.1.Matters needing attention in connection of Mine
Machine
Mine machine 12V power line, power supply control line, fan line must be
correctly connected, if due to the connection error, resulting in control board,
3
force board burning, the whole machine and veneer will not belong to the scope
of warranty!
2.1.1.Points for attention in connection of Control Panel 12V Power Line
When connecting the power cord of the control board, the plug of the power cord
and the clasp at the two ends of the power outlet of the control board must
correspond to each other, and the plug of the power cord cannot be inserted into
the control board socket by force. If backplugged, power on could burn down the
control board and burn out the signal wiring
Correct connection of power cord plugs and sockets:
Wrong connection of power cord plugs and sockets:
2.1.2.Matters needing attention in connection of Power supply Control Line
The power supply control line is 3pin red, black and yellow wire, 3 small ports
face out, the slot is inserted relative bit:
4
2.1.3.Matters needing attention in connection of Fan Line
Fan line is 4pin blue, yellow and red black line, 4 small mouth outside, card
slot relative bit insert:
5
2.1.4.Matters needing attention in data wiring connection of Force Plate
2.1.5.Matters needing attention in connection of 12V Power Line with Power Plate
When connecting the power cord of the force board, the power cord connecting
post and terminal must correspond to each other (yellow power cord is connected
to the red cable, and the red pole is connected to the positive pole (V);). The
black power cord is connected to the black pole, and the black pole is
connected to the negative pole (V-), which is tightened with screws. If the
connection is reversed, the power supply may burn down the machine.
Correct connection method of power cord connecting post and
terminal:
6
2.1.6.Machine wiring inspection
After all mine connections are connected, check again to confirm that the connection is
correct.
2.2.Mining machine handling, on the shelf operation
points for attention
In the process of ore machine handling and loading, data wire
arrangement, power control line, fan wire are strictly prohibited as
lifting handle, lifting machine and power supply. By connecting the
teena machine and the power supply, the connection will be damaged, the
connection will be loosened, and the control board will be physically
damaged over the carrying capacity. The resulting hardware damage and
failure will not belong to the scope of warranty!
7
3. Mine machine configuration environment
preparation
3.1.Mine machine configuration equipment list
Serial Serial number
Serial
number
name 1 numbe
1 tool
computer
1
1
tool
quantitative
use compu
r tool
mine
machine
comput
Mine
power
1
2
name configuration
remarks
name
ter 1
supply
quantita
network
operation
switch quantit
3
mine1
tive use
ative
machin
remarks DHCP/NTP
use
e
DHCP/
remark
server / router
configu
NTPs
4
1, provides
ration
server
dynamic IP
operati/
address 2 for
on
router
initial power
Serial number tool name
remarks
1quantitative
computer 1use
mine
machine configuration
Configuration
of mine
operation
power supply
Configuration of mine
machines and
configuration
DHCP/NTP server / router
1, provides dynamic IP
address 2 for initial
power on the mine
machine, and ntp
network time machine
Serial number tool
name quantitative use
remarks
Network switches
can connect to
external networks
DHCP/NTP server /
router 1, provides
dynamic IP address 2
for initial power on
the mine machine,
3.2.Mining machine network environment
By default, DHCP acquires dynamic ip, by default, so DHCP servers must be configured in the
mine network, or the dhcp dynamic ip address service must be turned on by the router. The
running time of mine machine and the correctness of calculation force statistics depend on the
network ntp time. By default, the mine machine has multiple ntp server addresses of public
network. In order to speed up the speed of obtaining network time by ntp and improve the time
precision, It is recommended that a local ntp server be configured in the mine network.
8
4.Mine machine connection and check before
power on
(1) before connection and electrification, the miner shakes the mine machine in accordance with
the warning signs on the side of the mine machine to check whether any radiator or other device
is off, to ensure that there is no radiator or other period of abscission before connection and
power up. (2) the mine machine is connected to the power cord, the network port is connected to
the switch, the control line of the power supply is connected to the I2C socket of the control board,
and the signal wiring, the power control line and the fan control line are checked, so as to ensure
that the connection is correct, In order to power the
mine.
Note: (1) 12V power cord connection post and terminal, control board power cord
socket outlet corresponding to ensure the correct connection of the power source
positive and negative pole, otherwise the power line positive and negative pole
connection, it is possible to burn the power board, control board or power
supply, Hardware damage due to power cord connection is not covered by warranty.
(2) the power supply control line must be connected between the control board
and the power supply, otherwise, the problem of low calculation force may be
caused by the failure to control the output of the power supply voltage. (3) the
control panel must be reliably connected with the fan line. If the fan line
falls off or the connection is bad, it may cause the miner to be unable to cool
down, and the load plate can be operated at lower frequency. In 2003, the
calculation power decreased.
9
5.Mine data configuration (configured on the
web page)
5.1.Query dynamic ip address obtained by mining
machine
5.1.1.Running WhatsMinerTools Software
The data of mine machine is configured with PC connected to the same network
where the miner is located, running the WhatsMinerTools software on PC, selecting
the "probe ip" tab, setting the room number, rack number, layer number on the
rack, and position number of the layer in which the mine machine is located.
Click start。
5.1.2.Query the ip address reported by the mine machine
The main results are as follows: (1) after 30 s, the yellow light and green light
of the net are always on and the green light twinkles under normal conditions.
When the IPFOUND function button (prominent long button) is pressed on the panel
of the mine machine control board, the two LED indicator lights on the right
flicker several times, indicating that the mine machine has broadcast the IP and
MAC addresses of the mine machine to the network.
10
（2）In the WhatsMinerTools software to view the dynamic access to the mine
machine reported IP,MAC address, mining machine location.
Note: (1) if all the lights in the control panel of the mine machine are not on after the power is
turned on, please check the 220V power supply line, the 12V power cord connection is reliable
and the connection is correct. (2) if the indicator light on the right side of the mine machine
control panel is not on, or the green light does not flash, please check whether the switch is
normal, whether the connection is reliable, and whether the quality of the wire is defective. (3)
the computer and miner running WhatsMinerTools software must be under the same net
segment, otherwise it is possible that the software can not receive the broadcast message from
the miner, so that the miner cannot be queried. Ipfound key reported ip address and mac
address information. (4) if the computer and the mine machine are under the same network
segment, and the dhcp service is turned on in the network, after pressing the ipfound button of
the mine machine, the WhatsMinerTools software does not inquire about the ip, length of the
mine machine and presses the reset button on the mine machine panel for more than 5s, so that
the default configuration of the factory is restored. Then reboot the machine, then press the
ipfound button to detect the ip address of the mine machine after 30 s. (5) if the computer is
running WhatsMinerTo Ols software, click "start", not manually press the ipfound button, the
software automatically found the mine machine's ip address, mac address, at this time, the
miner's ipfound key may be stuck by the surface plate, Find the mine machine that shows the
mac address in the software (the mine machine panel has mac address bar code), then reinstall
the control panel to make sure that the control panel button and indicator light reveal the
installation hole, and there is no jam.
11
5.2.Mine Pool & Miner data and configuration NTP
Server address
5.2.1.Mine Pool & miner disposition
(1) after logging in, go to the Cgminer configuration page. (2) in the
Cgminer configuration interface, modify mine pool address, miner name, and
after modification, click "Save & Application" in the lower right corner to
save the modified configuration.
The name of the miner.
Mine number
After the mine pool configuration is modified, the modified configuration must restart the
cgminer program or the control panel before the modified configuration can take effect.
（3）Restart cgminer, to check that configuration changes take effect. In
the mine machine interface, select: Status- > CGMinerStatus, into the CGMiner
running state interface.
12
In the cgminer status interface, click RestartCGMiner to restart the cgminer
process.
(4) restart the control panel and check whether the configuration changes are
effective. (if you do not choose to restart cgminer, configuration changes saved, you
can also restart the control panel, so that the configuration takes effect) in the
system interface, click "Reboot".
`
In the restart screen, click Perform reboot for restart confirmation.
After restarting about half a minute, the mine machine system will automatically jump to the
13
login interface.
5.2.2.Modify the address of the ntp synchronization server
(optional)
(1) after login, select: Configuration- > CGMiner Configuration, in the interface
to enter the Cgminer configuration page.
(2) in the cgminer configuration interface, the address of four ntp servers has
been configured by default when the ntp server address is added or modified, and
the address of the ntp server can be modified or added to the local ntp server
address according to the situation of the mine.
Default ntp server configuration: -p 3.asia.pool.ntp.org -p 2.cn.pool.ntp.org -p
1.cn.pool.ntp.org -p0.cn.pool.ntp.org followed by the ntp server domain name or ip
address, The ntp server address can be modified or added according to the
situation of the mine.
(3) after modifying the address of the ntp server, click "Save & Application" in
the lower right corner.
14
5.3. Configure mine machine static IP address (optional)
The IP address obtained by mine machine DHCP is modified to static IP address of
mine operation network planning.
(1) input the queried mining machine dynamic ip, in the browser with root user,
default password: root, login mine machine interface.
(2) after logging into the mine machine, select: Configuration- > Interfaces, to
enter the configuration interface of the network interface in the mine machine
interface.
(3) in the "Configuration" interface, click "Edit"
15
(4) in the interface modification interface, the protocol (protocol) selects
"Static address" and then clicks "Switch protocol".
(5) in the static address configuration interface, the IP address, mask, gateway,
broadcast address and DNS address are changed to the actual planned address of the
mine. Click "Save & Apply" in the lower right corner after modification.
16
保存应用后，需要重新用新设置的静态 IP 地址才能登录矿机（否则一直页面显示
加载中直到加载失败）。
After saving the application, you need to re-use the newly set static
IP address to log in to the mine machine (otherwise, the page appears
loaded until the load fails).
5.4. English and Chinese language switching of Mining
Machine Page
6.Mine machine running condition check
After the ore machine is connected to the running network, log in the mine machine
and check the running state of the mine machine.
(1) in the mine machine interface, choose: Status- > CGMiner Status, to enter the
cgminer running state interface.
(2) check the whole calculation force of mine machine, the speed of fan before and
after, connect mine pool, single board calculation force, single board temperature
and so on.
17
Note: (1) if the connection of the mine machine is correct and the network is normal, the
frequency search test will begin automatically after the mining machine is powered on. The
frequency search test phase will take about 15 minutes. After the frequency search is over, it will
only enter the formal mining stage. What is shown here is the calculation force of normal
operation. If the search frequency is not over, see the calculation force will be lower than the
normal operation of the calculation force.
(2) if the temperature of the outlet is above 85 degrees and the speed of the fan is more than
6100 revolutions, the miner will run at a lower frequency and the calculating force will be lower
than the normal one. Ventilation and cooling measures should be done to ensure the mine
operation environment. The ambient temperature of the machine is below 40.
(3) if the fan line is not reliably connected to the control board, the corresponding fan rotation
speed in the mine machine interface is 0, which leads to the excessive temperature of the mine
machine, the reduction of the frequency of the force plate and the decrease of the calculating
18
force.
(4) (4) if the temperature is not detected in the state interface and the temperature is not
detected, it is necessary to lower the electric power line of the mine machine and reinsert the
power line of the corresponding force plate, and the two ends of the data wire arrangement (one
end of the control board and one end of the force board) to ensure the reliability of the
connection.
7.Batch data configuration, status check, firmware
upgrade
WhatsMinerTool software can be used for batch data configuration, status check, firmware
upgrade, detailed operation see "Shenma mine machine WhatsMinerTool operation guide".
8.Disassembly and installation of
integrated machine
8.1. Disassembly and installation of Power supply
8.1.1.Power disassembly machine
1）.Unplug three load board connections (see figure 1 / 2 / 3), two fan lines (see figure 4 / 5) and
one power line (see figure 6) before removing the power supply
19
After drawing, as shown in the
figure:
2) Separate load plate connection columns are removed (at the outlet side) in turn, as shown in
thefigure:
20
After disassembly, as shown in the
figure:
2) The third step is to remove the eight screws on both sides of the fixed power supply, as shown
inthefigure:
21
2）.Pull out the power supply from left to right (note that the power cord is not broken), as
shown in the
figure:
After the power supply is removed, the figure is as
follows:
22
8.1.2.Installation of power supply
1）.1) when installing the power supply, fix the 4 screws of the control panel cover bracket first,
then adjust the position of the armrest support and then tighten the screw, as shown in figure:
2） make sure to tighten the screws when connecting the bar with the terminal, otherwise it will
affect the calculation force, as shown in figure:
23
3）.The control board of the line corresponding to plug-in, the power installation is complete.
8.2.Disassembly and installation of Control Panel
8.2.1.Disassembly of control panel
1）.1) remove the 2 screws of the fixed control and the 4 screws of the support of the fixed
control plate respectively, as shown in the figure:
2）Remove the four baffle screws from the outlet of the fixed power supply, as shown in the
figure:
24
2）Then move the control panel support from left to right, and the control panel is removed from
right to left, as shown below:
8.2.2.Installation of control panel
The mounting direction of the control panel is arranged in reverse order according to the control
board removal, and the screws are tightened accordingly to prevent the control board from
loosening.
25
8.3.Disassembly and installation of Force Plate
8.3.1.Disassembly of force plate
1）.There are three force plates on each machine, and the corresponding relationship between
the control board and the control board is shown in the figure.：
2）.To remove the problematic force plate, the four baffle screws and the corresponding
connecting posts for the fixed outlet fan need to be removed, as shown in the
figure:
26
3）.After the connection column corresponding to the fan and the force plate is removed, the
faulty force plate is extracted, as shown in the
figure:
4）.After taking out the force plate, use WeChat to scan the serial number of the force plate and
provide it to the relevant after-sales technicians, as shown in the
figure:
27
28
8.3.2.Installation of force plate
1）.1) when the force plate is loaded into the chassis, one hand holds the force board into the
force board slot, a portable starting force board connecting column and the force board
connection line, and the sequence enters the chassis, as shown in figure:
29
2）.2) after the installation of the force plate, install the fan. When installing the fan, pay
attention to the fan connection line on the right, be careful of the wrong direction, or you will
need to reinstall, as shown in the figure:
30
31