Shoprider Torino S-778XLSBN User Manual

Torino
Model: S-778XLSBN
USER MANUAL
Please ensure that this manual is read and understood before
using the scooter.
Nov 2011
Contents
Page
Introduction
2
Intended Use
2
Feature Guide
3
Safety Advice
4
Adjustments
 Tiller angle
 Seat slide
 Seat swivel
 Seat height
5
5
5
5
Tiller Controls
6&7
Brake Release / Freewheel Operation
7
Starting to Drive
 Getting Started
 Moving Off
 Steering
 Reversing
 Gradients and Kerbs
8
8
8
8
8&9
Technical Specification
9
Batteries and Battery Charger
10
Maintenance
11 & 12
Troubleshooting
 Circuit Breaker
 Fuses
 Check List
12
12
13
Further Information
13 & 14
Warranty
1
Introduction
Congratulations on your purchase of the Torino scooter. This scooter
incorporates comfort and style with the latest in technology. The large tyres,
powerful motor and full suspension ensure a comfortable ride. It is also
complemented with a full light set that includes front and rear lights, indicators
and hazard warning lights enabling it to be used on public roads.
Intended Use
The Torino was carefully designed for persons with limited mobility. It is for
predominantly outdoor use by a single occupant up to a maximum weight of
220kg / 35st.
The intended user should possess the necessary physical, visual and cognitive
skills to operate the scooter safely. If you have any doubt, please consult your
dealer / prescriber.
Note: Persons with lower body amputations should not use this device
unless evaluated with artificial limbs fitted, as stability may be
compromised due to an irregular centre of gravity.
The Torino is a Class 3 invalid carriage and is not legally defined as a motor
vehicle, and therefore the user is not required to possess a driving license. It is
exempt from MOT certification. It must however be registered with the DVLA
and display a nil duty vehicle license (tax disk).
A Class 3 invalid carriage can only be used by a person suffering from some
physical defect or physical disability aged 14 or over, or by an able bodied
person who is demonstrating a vehicle before sale, training a disabled user or
taking the vehicle to or from a place for maintenance or repair.
A Class 3 invalid carriage can be used on public roads, but not on motorways,
cycle lanes or bus lanes. When used on pavements or in pedestrian areas the
scooter MUST be switched to its lower speed limit (see page 6). It is not
recommended that the scooter is used on a dual carriageway, but if it is
necessary an amber coloured flashing beacon must be used to warn other road
users of your presence.
It is important that the user reads and understands the safety advice given within
this manual before attempting to operate the product to avoid possible injury to the
user or bystanders and avoid damage to the scooter or surrounding property.
2
Feature Guide
1
2
3
9
4
8
5
7
6
1. Rear view mirror
2. ‘Delta’ type tiller control
3. Fully adjustable ‘Captains’ seat
4. Width adjustable armrests
5. Rear lights with indicators
6. 14” non marking tyres
7. Front headlights
8. Angle adjustable tiller
9. Front basket
3
Safety Advice
DO:











Read this manual carefully before using your scooter.
Turn the power off when transferring to and from the scooter.
Select a slow speed when going down gradients or over uneven ground.
Keep your feet inside the scooter whilst driving.
Ensure the batteries are fully charged before your journey.
Avoid rough or soft terrain and long grass wherever possible.
Be aware of other road users and pedestrians. If driving on the road you
MUST adhere to the Highway Code.
Use lights whenever necessary.
Turn the power off when not in use.
Follow the maintenance guide to ensure safe operation of the scooter.
Always remove the keys if leaving the scooter unattended. Unauthorised
persons/children may use the scooter resulting in injury.
DO NOT:






















Carry passengers.
Carry bags, luggage or walking aids on or near the tiller control other
than in the basket provided.
Exceed inclines over 8° (14%).
Traverse inclines.
Attempt inclines if the surface is slippery.
Turn sharply at full speed.
Exit or enter the scooter unless the power is switched off.
Switch off the power whilst driving – this will cause the scooter to stop
abruptly and could damage the controls.
Use the scooter where you cannot safely or legally walk.
Attempt to climb kerbs over 10cm (4”) high.
Use the scooter in high winds (38mph+) if fitted with a canopy.
Use the scooter if under the influence of alcohol or any medication.
Use a mobile phone whilst driving.
Attempt to negotiate steps or escalators.
Transport the scooter with the user onboard.
Attempt to tow any other devices.
Exceed the stated weight limit.
Connect any other devices to the batteries as this could cause permanent
damage and void your warranty.
Use any other batteries/charger other than those supplied by RMA.
Travel through water or over soft terrain (mud, sand etc.).
Lift the scooter by the chassis covers or any plastic part.
Store the scooter outdoors uncovered for any period of time. We
recommend that the scooter is stored in a dry garage, shed or porch to
prevent the possibility of any moisture ingress.
Every care has been taken to ensure that your scooter will give you safe, reliable
service provided you adhere to the advice given above.
4
Adjustments
Tiller Angle Adjustment
On the left side of the tiller base is a red
lever. Push the lever in to release the pin
and select the required angle. Pull the lever
back out and ensure the pin is securely
located in one of the five adjustment holes.
Red Lever
Seat Slide Adjustment
Your Captain seat can move forward or
backwards similar to a car seat. Lift lever (1)
up and slide the seat to the required
position. Release the lever to lock it back in
place.
1
2
3
Seat Swivel adjustment
For easy transfers, the seat can be swivelled to the side. Lift the red lever (2) and
carefully rotate the seat to get on or off. Pulling up on this lever and the seat
simultaneously will allow the seat to be removed.
Always ensure the seat is locked in the forward facing position when in use.
DO NOT attempt to drive when swivelled as this may result in injury.
Seat Height Adjustments
First, remove the seat by pulling up on the red lever and lifting the seat
simultaneously. The seat height may be adjusted by undoing the handknob (3)
completely and removing the rear chassis cover (take care with the wiring looms
for the rear lights). Remove the locking pin and adjust the seat adapter to the
required height. Re-insert the locking pin fully and ensure the lock wire is in
place. Replace the rear chassis cover, re-tighten the handknob and replace the
seat.
5
Continued…..
Armrest Width Adjustment
The armrest width can be adjusted by
loosening the two handknobs at the rear
base of the seat, moving the armrest to the
required width and re-tightening the
handknobs.
Handknobs
DO NOT use the scooters with the armrest
removed. The armrests should not be used
for full support when transferring from the
scooter. Swivel the seat and seek
assistance whenever necessary.
Armrest Angle Adjustment
The angle of the armpad can be adjusted by
tightening or loosening the screw under the
armpad. Tightening will raise the angle and
loosening will reduce the angle.
Adjustment
Screw
Dis-assembly
The Torino scooter can be ‘broken down’ into five components for
transportation – Front Chassis, Rear Chassis, Seat and Batteries (x2).
Care should be taken when dis-assembling the scooter. Components can be
heavy so assistance should be sought when lifting.
Remove the seat and rear chassis
cover as previously described.
Undo the battery connections and
the large orange main loom plug.
Undo the Velcro straps and remove
the batteries.
Disconnect the rear brake cable
from the rear brake hub.
Locate and remove the locking pin,
which is situated as shown in the
image opposite.
6
Tiller Controls
Speed Control:
This allows the user to set the maximum speed of the scooter between 1
(minimum) and 10 (maximum).
Battery Level Indicator:
The number of LED bars lit gives an indication to the amount of charge
remaining in the batteries. The amount of charge will only show it’s true level
when the scooter is being driven. Do not allow the LED bars to go out
completely as complete discharge of the batteries could cause permanent
damage to your scooter.
High/Low Speed Switch:
This sets the maximum high speed for the scooter. This MUST be set to low
when used in pedestrian areas. The ‘HIGH’ setting should only be selected when
used on the road.
Hazard Warning Lights:
This red button operates all of the indicators simultaneously.
Lights:
This blue button operates the main front and rear lights.
Key Switch:
The key switch operates the main power for the scooter. When turned clockwise
the battery level indicator should light up indicating that the scooter is on. There
is a small delay before the thumb lever controls operate as the controller checks
the main circuits. Do not turn off the power whist moving, this will cause the
scooter to stop abruptly.
7
Continued…..
Horn:
This yellow button operates the scooter’s horn. The horn should only be used to
warn others of your presence and not as any form of rebuke.
Thumb Lever Control:
The left thumb lever controls the reverse and the right thumb lever controls the
forward motion of the scooter. The further you push the lever the faster the
scooter will travel. Releasing the lever will slow the scooter to a safe stop and the
electro-magnetic brakes will apply automatically.
Charging Socket:
Please refer to page 12 ‘Batteries and Battery Charger’
Indicator Switch:
This switch operates the indicator lights of the scooter. Please use the indicators
at all times when making manoeuvres on roads.
Brake Release / Freewheel Operation
The release lever for the electromagnetic brake is situated under the
rear left of the scooter. Ensure that
the power is switched off.
In the event of power failure or the
need to mover the scooter without
driving, the electro-magnetic brake
can be disengaged by a pulling the
red lever upwards – this will then put
the scooter in ‘freewheel’ mode. To
re-engage the brakes push the lever
down fully and ensure that the brake
is engaged before entering the
scooter.
Caution! NEVER leave the scooter unattended whilst in freewheel mode as it
will roll away down an incline. ‘Freewheel’ mode should only be used in an
emergency to move the scooter due to power failure. NEVER move the
scooter in this mode whilst it is occupied. Your scooter will continually
bleep if it is switched on when in this mode.
8
Starting to Drive
Getting Started
Select a level area with plenty of space.
Enter the scooter and adjust the tiller and seat as previously described to the
desired driving position.
Moving Off
Turn the key clockwise to turn on the power.
Ensure your batteries are fully charged.
Initially set the speed to 1 or 2.
Press your right thumb lever, the scooter should move forward slowly. The
harder you press the lever the faster the scooter will travel up to it’s preset
maximum speed. Releasing the lever will bring the scooter to a safe stop and the
electro-magnetic brakes will be applied automatically.
Steering
Steering the scooter is light and easy. Ensure when starting off you give a wide
clearance when turning so that the rear wheels can clear any obstacle that you
are passing. When steering through limited spaces such as doorways or when
turning around, turn the tiller handle in the direction you want to go and gently
apply the power. NEVER turn sharply when travelling at high speed as this
may affect stability.
Reversing
Before reversing ensure that the area behind the scooter is free from any
hazards or obstructions. Adjust the speed setting low before you reverse. Press
the left thumb lever and steer wide of all corners and obstacles.
Caution! Do not reverse onto a main thoroughfare. Take care, objects in the
rear view mirrors will appear to be further away from the back of the
scooter than they actually are.
Gradients and Kerbs
We recommend that wherever possible that a suitable access point such as a
drop kerb or ramp be used. The necessity to climb a kerb directly should be
as a last resort.
If negotiating a gradient or kerb (up to 10cm), always address the situation at an
angle of 90° to ensure stability of the scooter. Do not hit a kerb at speed, drive
slowly until you reach the kerb then apply more power to travel over the
obstacle. Do not turn sharply on any slope moving forwards or backwards.
9
Continued…..
Caution! Always ensure that the power is turned off when entering or
dismounting the scooter. Take plenty of time to become familiar with the
way that the scooter behaves. DO NOT drive on public roads until you have
the confidence and ability to do so.
Technical Specification
The Torino is classified as:
Class 1 Medical Device (93/42 EEC)
Class 3 Invalid Carriage
Overall Size
Length
Width
Height
Max. Speed
Seat Height to floorpan
Maximum user weight
Safe Working Slope
Seat Dimensions
1360mm
680mm
1270mm
12km/h
(8mph)
430-505mm
220kg / 35st
8 (degrees)
Width
Depth
Height to floor
Backrest height to lowest
seat
Battery charger (off board)
Ground Clearance
Range (maximum)
500mm
440mm
630-705mm
660-790mm
8 amp
150mm
55km/35m*
* Passenger weight, steep inclines, ground conditions, ambient temperature and
battery condition can affect maximum range.
10
Batteries and Battery Charger
Batteries
The Torino is supplied with two, maintenance free, sealed AGM batteries. These
are fitted under the seat on the scooter.
Battery performance can be affected by low temperatures, rough terrain and the
weight of the user. Your battery gauge is a guide only on the level of charge
remaining in the batteries.
An active user can use 30% of the battery capacity or more per day.
An inactive user may only use 50% of the battery capacity in a week.
Battery Charger
Charge the batteries completely (8-12 hours) prior to first use.
Batteries supplied with your scooter are specially designed for use on
powerchairs and scooters and require an automatic battery charger. These
chargers have an electronic switch that terminates the charge when the
batteries are full.
The battery charger is an 8-amp switch mode type off board. The charger is able
to read the level of charge in the batteries and will switch off when the batteries
are fully charged.
To charge the batteries connect the plug lead into the charging socket (page 8)
on the tiller and the 3-pin plug into the wall socket and switch on.
The battery charger has two lights. A constant red light will show when the
battery charger is connected (this will flash if there is a break in the connection).
The orange light indicates that the batteries are receiving charge, this will
change to green when the charging cycle is complete.
Caution: Always charge the batteries in a well-ventilated indoor area. You
must still maintain charging the batteries even if the scooter is not to be
used for a prolonged period of time (2 to 3 weeks). Failure to do so could
result in permanent damage and render the batteries unusable. Wherever
possible do not interrupt the charge cycle until the batteries are fully
charged. Continual interruption can permanently damage the batteries. If
the charging lead should become damaged discontinue use immediately
and seek a replacement from your dealer.
Disposing and recycling of used batteries
Batteries must always be recycled correctly. Do not dispose of them with your
domestic refuge.
For further information regarding your nearest recycling facility please contact your
local authority.
11
Maintenance
Cleaning the Scooter
When cleaning the scooter please pay attention to the following points:





Only use a damp cloth and gentle detergent.
DO NOT use any abrasive products.
DO NOT use a hose or pressure washing equipment.
AVOID water contact with any electrical components.
DO NOT put the scooter through an automated car wash or similar.
Annually
Monthly
RMA Scooters
Maintenance and Inspection
Daily
Weekly
Routine Maintenance
We recommend that the following checks be carried out on a periodical basis by
a qualified person:
Check / Charge Batteries
Check removable parts are secure
Check electrical connections are secure
Check tyre pressures (30 psi rear, 25 psi front)
Check tyre wear (minimum 2mm tread depth)
Lubricate wheel / castor bearings with a light oil
Complete inspection by an authorised Dealer
 


 


  

  

  


  


 
The transaxle/gearbox is a sealed unit and does not need lubricating.
Wheels and Tyres
The wheels of your scooter have split rims. This allows any punctures to be
repaired easily.
To change the wheels, remove the centre bolt and slide the wheel off its axle.
Ensure that when refitting the wheel the retaining nut is fitted with a locking
washer or the screw threads are treated with ‘Loc-tite’ or a similar thread locking
compound. When changing a tyre the inner tube must be deflated. Remove the
four bolts from the wheel and slit the rim. Tyre pressure is recommended to be
kept at 30psi on the rear and 25psi on the front tyres.
Note: Regularly check and maintain these tyre pressures, as low tyre
pressure can reduce the range of your scooter.
12
Continued…..
Product Life Expectancy
Your scooter has been designed to provide the user with a long, reliable life
provided it is correctly maintained and regularly serviced by an authorised
dealer. However, due to inevitable wear and tear and technological
improvements it is recommended that the average usable life of this scooter is
five years.
Note: Should any parts need replacing during routine maintenance please
consult your local Dealer for approved spare parts for your scooter. Failure
to do so may damage the scooter and void your warranty.
Troubleshooting
Circuit Breaker
Your scooter is fitted with the latest in electronic controls
that are programmed to protect the electrical system from
abnormal overloads. Fitted for extra protection is a circuit
breaker. Should there be a situation where your scooter
stops for no apparent reason please check that the circuit
breaker has not tripped. The circuit breaker is located is
located through a hole in the shroud underneath the seat
behind the seat post. Press this button to reset the circuit
breaker.
Note: Should the circuit breaker continue to trip turn off the scooter
immediately and consult your dealer.
Circuit Breaker
Reset
Fuses
Inline 100 amp blade type fuses from the batteries protect any overload,
and a 15 amp fuse is located in the battery charger as extra protection.
Note: Should the fuses need replacing please contact your dealer to
ensure the correct sizes are fitted. Failure to do so could result in
permanent damage to the scooter’s electronics and possibly cause a
fire hazard. Failure to do this will void your warranty.
13
Continued…..
Check List
If you scooter fails to operate, please check the following:
 The unit is switched on.
 All plugs and connectors are firmly fixed.
 Battery level shows full charge.
 Freewheeling device is in the drive position (lever down).
 Circuit breaker has not tripped
If the freewheel device has been operated with the scooter left switched on, the
scooter will bleep continually and not operate until the ignition key has been
switched off then on again.
Please consult your dealer if your scooter does not run after checking these
points.
Further Information
Safety Information Regarding Electromagnetic Interference (EMI)
Scooters and powerchairs are designed to operate under certain conditions.
However, radio waves or electromagnetic fields may affect the operation of the
scooter. The source of EMI could be radio or television transmitters or portable
devices such as mobile phones, portable CB radios etc.
Should any unintentional movement occur turn the scooter off as soon as safely
possible.
Solar Energy
During periods of sunny weather, it is possible that surfaces of your scooter may
reach high temperatures (as with motor vehicles). Please take precautions if
leaving the scooter in direct sunlight for any period of time. Seek shade or cover
the seat and hand controls to keep any temperature increases to a minimum.
Health Factors
Suitability for this product has been assessed on the user’s current state of
health. It is essential that the user regularly monitor their ability to use the
scooter safely.
Please read and adhere to the guidelines set out in this manual and in the ‘Code
of practice for Class 3/C vehicle users’
Disposal and the Environment
Parts of this product are covered by the Waste Electronic and Electronic
Equipment (WEEE) regulation. It should not be discarded with normal
household/domestic waste, but taken to your local collection centre for
recycling. For further information, please contact your local authority or
approved disposal agency.
14
Continued…..
General Use
Take heed of the information given in this manual regarding safety and the
maintenance of your scooter. If adhered to, your scooter should give you years
of reliable mobility.
The Torino is intended for general year round use. However, DO NOT use the
scooter in electrical storms, high winds (if fitted with a canopy) or downpours.
Care must also be taken during cold weather due to icy surfaces.
Storage and General Care
We recommend that the scooter is always stored in a dry environment such as a
garage or shed to protect the chassis and other components from corrosion or
water damage. Do not leave the scooter outside during rainstorms. If the
scooter is wet, wipe with a dry cloth to ensure there is no ingress of water into
the internal components of the scooter (If the scooter needs to be cleaned, use a
mild detergent and warm water with a damp sponge or cloth. DO NOT throw water
over the scooter).
Product Stability
Scooters and powered wheelchairs are designed to allow the user flexibility of
movement in restricted areas. Driving at maximum speed and attempting sharp
turns can create a situation where the product becomes unstable. Therefore it is
essential that the user pay attention the guidance set out in this manual.
For maximum stability the speed setting should be set up to 50% of the
maximum available (halfway between the tortoise and the hare or just
entering the red sector on the speed indicator depending on the model).
The main factors affecting stability are:
 Maximum speed setting
 Seat height
 User movement
 User’s manoeuvres
 Gradients or slopes
Please keep your speed to a level where you can safely stop without having to
make any erratic turns.
Do not load bags etc. on the back of the seat as this will affect the centre of
gravity and could increase instability.
Do not lean outside of the ‘footprint’ of the product, especially whilst moving.
Avoid making turns on gradients or slopes.
Transportation
You may transport your scooter in many ways. Wherever possible, secure the
scooter. We do not recommend that scooters be transported on an open
bottomed trailer.
15
Continued…..
Sleep Mode
Your scooter has a digital battery status indicator, which displays the current
charge status of the batteries in your scooter.
The circuitry also detects changes in power draw from the batteries.
If you scooter is left switched on without use for about five minutes the
electronics will go into ‘sleep’ mode to conserve power. You will see one bar on
the battery status indicator oscillate from side to side. Simply switching the
scooter off and back on will enable the scooter to operate as normal.
Constant Speed Use
As the circuitry senses changes in power draw it is possible that on journeys
where your speed is constant for an extended period of time that you will see
the single bar oscillate even though the scooter is in motion. This is due to the
prolonged period of no change in power draw.
This is perfectly normal and by simply adjusting your speed for a moment will
change the battery status indicator back to normal.
Driving in Pedestrian Areas
When using the scooter in pedestrian areas always lower your maximum speed
to that of the pedestrians around you. Remember the stopping distance of your
scooter and always allow enough space to stop safely to avoid collisions with
pedestrians or other objects.
Emergency Procedures
Should your scooter behave erratically or become unresponsive whilst driving,
release the wig-wag lever so it may return to it’s neutral position and switch off
the power at the key / switch. These procedures will stop the scooter and
activate the braking system, preventing any further uncontrolled manoeuvres.
Note: Switching the power off at the key / switch can cause the scooter to stop
abruptly and should only be used to stop the scooter during an emergency
16
Notes
17
Notes
18
Warranty Terms and Conditions
This is to certify that your Shoprider product is warranted for a period of 12
months from the date of original purchase. This warranty is not transferable.
Should a defect or operating fault arise within this period the Dealer from
where the product was originally purchased should be notified
immediately. Failure to register the fault may invalidate the warranty.
The Dealer from where the product was purchased is responsible for any
warranty repairs.
If a fault occurs within this period due to faulty workmanship or materials that
the product will be repaired (or replaced at the Companys discretion) free of
charge.
Any unauthorised modifications will invalidate the warranty.
Parts which are subjected to normal wear and tear, accidental damage, neglect
or misuse are excluded from this warranty. Normal wear and tear includes tyres,
chassis covers, bulbs, seat coverings etc.
Component parts replaced outside this period carry a six-month warranty.
(Standard terms and conditions apply for this period).
Model:
Serial No:
Purchase Date:
Dealer Stamp
Distributed by:Roma Medical Aids Ltds
York Road, Bridgend Industrial Estate,
Bridgend
CF31 3TB
Tel: 01656 674488 Fax: 01656 674499
Email: [email protected]
www.romamedical.co.uk
Shoprider reserve the right to change specifications without prior notice
Manufactured by:
Phisiang Machinery MFG. CO. LTD
No. 108 Hsin-He Rd, Hsin-Feng Hsiang, Hsinchu County, Taiwan
">