ELDAT RCL04 Low-voltage mini receiver Operating Manual

EN
RCL03 | RCL04
Mini Receiver
Safety Advice
Models
P2
P1
LED
1
2
X5
3
4
5
~
+
~
J1
X6
T2
14 11 12 24 21 22
CH2
CH1
VIN
12-24VAC
12-32VDC
T1
arefully read through these instrucC
tions before connecting and operating
the receiver!
Caution! Observe the permissible supply voltage and the max. contact rating!
Have faulty radio controls checked by the
manufacturer!
Do not make any unauthorized alterations or
modifications to the receiver!
Function
RCL03E5002B01
Degree of protection IP20
1
X5
2
3
4
5
~
+
~
J1
X6
14 11 12 24 21 22
CH1
P2
P1
LED
CH2
T2
T1
VIN
12-24VAC
12-32VDC
The RCL03 and RCL04 Easywave mini receivers
can be operated in a voltage range of 12-24 V AC
or 12-32 V DC.
Two potential-free relay outputs may be switched.
A total of 32 different Easywave radio transmission codes can be programmed. The memory
slots can be divided between the two outputs as
required.
If a transmitter is programmed into both outputs, it
still only occupies one memory slot.
It is also possible to connect one external button for each channel which can then be used to
switch the corresponding relay according to the
selected operating mode.
To do this, the button inputs T1 and T2 must be
wired to the supply voltage VIN1.
Operating Modes
RCL04E5002B01
Degree of protection IP65
Technical Details
Frequency:
Modulation:
Coding:
Power supply:
- AC:
- DC:
Current consumption:
Degree of protection:
Input:
Output:
Max. contact rating:
- AC:
- DC:
Operating temperature:
Dimensions:
Weight:
868.30 MHz
FSK
Easywave
12-24 V
12-32 V
0.18 W standby
0.6 W relay switched
(w/o load)
RCL03: IP20
RCL04: IP65
2 external buttons
2 potential-free
relay contacts (changeover)
60 V / 1 A / 60 VA
60 V / 1 A / 30 W
-20°C to +60°C
RCL03: 70 / 64 / 35 mm
RCL04: 72 / 114 / 36 mm
RCL03: approx. 50 g
RCL04: approx. 100 g
Scope of Delivery
Mini receiver, mounting accessories (RCL03:
adhesive pad, RCL04: screws and anchors),
operating instructions
Intended Use
The unit may only be operated with safety extra
low voltage (SELV) and may only be used as a radio control for switching devices with safety extra
low voltage (SELV).
The manufacturer shall not be liable for any damage caused by improper or non-intended use!
The radio control can be operated in five different operating modes with Easywave transmitters
for 1-button-, 2-button- or 3-button operation. The
operating mode can be selected with jumper J1.
PULSE
1 2 3 4 5
J1
(1-button operation)
If a transmitter button or an external button is
pressed, the corresponding relay is triggered for
1 second.
ON/OFF
1 2 3 4 5
J1
(2-button operation)
Each relay can be switched separately ON and
OFF.
The external buttons toggle between ON and
OFF in this operation mode.
transmitter button
function
A or C
ON
B or D
OFF
MOTOR CONTROL
1 2 3 4 5
(UP/DOWN)
J1
(2-button operation)
The relays are controlled in combination and
are interlocked.
STOP with opposite direction
transmitter button
A or C
External button T1
function
B or D
External button T2
DOWN
UP
STOP
for DOWN direction
STOP
for UP direction
The maximum runtime is 90 seconds.
DEAD MAN´S MODE
1 2 3 4 5
J1
(1-button operation)
Each relay can be switched separately. The relay
is triggered as long as the corresponding transmitter button or the corresponding external button is pressed (transmitter button operation max.
36 secs).
MOTOR CONTROL
(UP/STOP/DOWN)
J1
1 2 3 4 5
(3-button resp. 4-button operation)
The relays are controlled in combination and are
interlocked.
transmitter button
function
A
UP
B
DOWN
C
STOP
D
STOP
The external buttons behave as if they are
in 2-button motor operation mode!
The maximum runtime is 90 seconds.
Mounting and Connecting
1. Remove the housing cover.
2. Mount the receiver on a suitable location, using the mounting accessories supplied.
Make sure there is no interference with
the wireless connection. Do not mount
the device in a distribution box, in metal
casings, in direct proximity to large metal objects, on the floor or close to it.
The maximum length of all connecting
cables may not exceed 3 m!
When connecting the RCL04, insert
all connection cables into the device
through the opening on the bottom via
the watertight PG screw connections.
3. Select the desired operating mode with the
jumper J1.
4. Connect the supply voltage and the safety
extra-low voltage devices according to the
connection diagram.
or
Connect the supply voltage and the devices
to be switched for the motor control according
to the connection diagram.
In the MOTOR operating mode, the
receiver may only be operated with
12-32 V DC.
5. If necessary, connect the external buttons to
the terminal T1 and T2.
The external buttons always use the
operation mode, currently set with the
jumper J1.
6. Program the codes of the transmitters to the
receiver (see section “Program transmitters“).
7. Put the housing cover back on.
Electrical Connection
Program transmitters
VIN1
14 11 12 24 21 22
VIN2
DEAD MAN´S MODE, ON/OFF and PULSE
In the programming mode you can transfer the
codes of your transmitter buttons to the receiver.
The operating mode set with the jumper J1 at this
point in time is adopted with the programming
process and is valid for the transmission code
currently programmed. A total of 32 transmission
codes can be programmed.
1. Briefly (< 1.6 sec.) press the programming
button P1 (for output 1) or P2 (for output 2).
The programming mode is activated. The LED
flashes.
2. Press one of the transmitter buttons to be
programmed and keep it pressed. When the
code has been saved, the LED lights up for 4
seconds and then flashes again. Release the
transmitter button.
Supply voltage (12-24 V AC/12-32 V DC)
VIN1,VIN2
Output 1 (CH1)
- normally open contact:
- normally closed contact:
terminals 11 + 14
terminals 11 + 12
Output 2 (CH2)
- normally open contact:
- normally closed contact:
terminals 21 + 24
terminals 21 + 22
MOTOR CONTROL
3. Repeat step 2 with other transmitters, if needed.
4. Leave the programming mode, by briefly pressing P1 or P2 again. The LED turns off.
In the operating modes with 2-button or
3-button operation, only one transmitter
button has to be programmed. The code
of the associated button is assigned automatically!
The programming of the receiver remains, even in case of extended power
failures.
If the LED flashes rapidly for approx.
4 sec, all memory locations are occupied. A transmitter can only be programmed again if another one has been deleted before.
VIN1
VIN2
Deleting transmitters
14 11 12 24 21 22
12-32V DC
EXTERNAL BUTTONS
T1
T2
~
+
In the delete mode you can delete specific transmission codes programmed into the receiver.
1. Keep the programming button P1 (for output
CH1) or P2 (for output CH2) pressed for longer than 1.6 sec. The delete mode is activated.
The LED flashes rapidly.
2. Press the selected transmitter button you
want to delete. As soon as the code has been
deleted, the LED lights up for 4 sec. and then
flashes again rapidly.
In the operating modes „motor control“
and „ON/OFF“, the code of the corresponding transmitter button will also be
deleted.
3. Repeat step 2 with another transmitter or
briefly (< 1.6 sec.) press the programming
button P1 or P2 in order to return to the operating mode. The LED turns off.
Disposal
Waste electrical products not be disposed of
with household waste!
Dispose of the waste product via a collection point for electronic scrap or via your
specialist dealer.
Put the packaging material into the recycling bins for cardboard, paper and plastics.
Warranty
Within the statutory warranty period we undertake
to rectify free of charge by repair or replacement
any product defects arising from material or production faults.
Any unauthorized tampering with, or modifications
to, the product shall render this warranty null and
void.
Conformity
Hereby, ELDAT EaS GmbH declares that the radio
equipment type RCL03 / RCL04 is in compliance
with directive 2014/53/EU and 2017/1206/UK. The
full text of the EU and UK declaration of conformity is available at the following internet address:
www.eldat.de
Customer Service
If the device does not work properly despite proper handling or in case of damage, please contact
the manufacturer or your retailer.
ELDAT EaS GmbH
Schmiedestraße 2
15745 Wildau
Germany
Phone: + 49 (0) 33 75 / 90 37-310
Fax:
+ 49 (0) 33 75 / 90 37-90
Internet: www.eldat.de
E-mail: [email protected]
VIN1
VIN2
T2
T1
Deleting Memory Completely (RESET)
External button 1 (for output 1/CH1)
In the Reset mode you can delete all codes programmed into the receiver.
1. Keep the programming button P1 or P2
pressed for more than 1.6 sec. The delete
mode is activated. The LED flashes rapidly.
2. Press the programming button P1 or P2 again
and keep it pressed for more than 1.6 sec. As
soon as the memory has been deleted completely, the LED lights up for 4 sec. and then
flashes again.
3. Briefly (< 1.6 sec.) press the programming
button P1 or P2 in order to return to the operating mode.
- terminals VIN1 + T1
- terminals VIN1 + T2
UM500394_0723 EN
External button 2 (for output 2/CH2)