advertisement
▼
Scroll to page 2
of 8
Item#: 8158BC Check that you have all the below parts for this model before assembling the playard. Playard x 1 Wheel x 2 Wheel Axle x 2 Retainer x 2 Cap x 2 Leg x 2 Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE. Long Curved Bar x 2 Short Bar with Connector Knob x 2 Parent Organizer x 1 Hook x 2 Bassinet x 1 Metal Support Tubes (2 male, 2 female) Mobile Lower Arm x 1 Mobile Arm Holder x 1 Mobile Upper Curved Arm x 1 Mobile Tri-shaped Arm x 1 Toy Animal x 3 Changing Table x 1 Travel / Storage Bag x 1 Mattress x 1 IF YOU EXPERIENCE ANY DIFFICULTY IN USING THIS PRODUCT, PLEASE CONTACT OUR CUSTOMER SERVICE DEPARTMENT AT 1-800-328-7363 BETWEEN THE HOURS OF 8:00 A.M. AND 4:30 P.M. PACIFIC STANDARD TIME FOR ASSISTANCE. PLEASE HAVE YOUR MODEL NUMBER AND MANUFACTURING DATE AVAILABLE WHEN YOU CALL. THIS INFORMATION CAN BE FOUND ON A SMALL STICKER UNDER THE PLAYARD. *Toys and mobile may vary Instruction Manual Convenience through innovation and thoughtful design 01.09 Contact us by mail: Baby Trend, Inc. 1607 S. Campus Ave., Ontario, CA 91761 Contact us by phone: 1-800-328-7363 (8:00am ~ 4:30pm PST) or online http://www.babytrend.com Convenience through innovation and thoughtful design www.babytrend.com WARNING WARNING: NEVER LEAVE INFANT IN PRODUCT WITH SIDES DOWN. Infant may roll into space between pad and loose mesh side causing suffocation. WARNING: Infants can suffocate: • In gaps between a mattress too small or too thick and product sides • On soft bedding Never add a mattress, pillow, comforter, or padding. Use only the mattress provided by manufacturer. Never use a water mattress with this product. WARNING: See playard floor and side rails for warnings. WARNING: Failure to follow these warnings and the WARNING • NEVER use this product if there are any loose or missing fasteners, loose joints, broken parts, or torn mesh/fabric. Check before assembly and periodically during use. Contact Baby Trend Customer Service at 1-800-328-7363 for replacement parts, repair or instructions. NEVER substitute parts. • NEVER leave child in product with sides lowered. Be sure sides are in raised and locked position whenever child is in product. • NEVER use plastic shipping bags or other plastic film as mattress covers not sold and intended for that purpose. They can cause suffocation. • This product is not intended for commercial use. MAINTENANCE AND CLEANING INSTRUCTIONS: Use only household mild soap and warm water. DO NOT USE BLEACH. DO NOT MACHINE WASH. instructions could result in serious injury or death. • The playard, including side rails, must be fully erected prior to use. Make sure latches are secure. • Strings can cause strangulation! NEVER place items with a string around a child's neck such as hood strings or pacifier cords. NEVER suspend strings over playard or attach strings to toys. • Discontinue use of the product when child is able to climb out or has reached the height of 35 in. (890 mm) or weight of 30 lbs. (14 kgs), whichever comes first. • When child is able to pull to standing position, remove bumper pads, large toys and other objects that could serve as steps for climbing out. • NEVER place product near a window where cords from blinds or draps can strangle a child. • Always provide the supervision necessary for the continued safety of your child. When used for playing, NEVER leave child unattended. • To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their back to sleep, unless otherwise advised by your physician. 1 Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved. If you experience any difficulty with the use of our product or have a question regarding these instructions, please contact our Customer Service Department at 1-800-328-7363 between the hours of 8:00 a.m. and 4:30 p.m. (PST). Please do not return the product to the store as once it is returned it cannot be re-sold and the materials and energy used to make it are wasted. Contact us by mail: Baby Trend, Inc. 1607 S. Campus Ave., Ontario, CA 91761 Contact us by phone: 1-800-328-7363 (8:00am ~ 4:30pm PST) or online http://www.babytrend.com Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved. 2 PARTS ASSEMBLY This model may not include some features shown below. Check the parts list to make sure you have all the parts for this model before assembling the playard. IMPORTANT! To ensure safe operation of your playard, please follow these instructions carefully. Please keep these instructions for future reference. IMPORTANT! Before assembly and each use, inspect this Wheel (2) Leg (2) Wheel Axle (2) Retainer (2) Playard Cap (2) product for damaged hardware, loose joints, missing parts or sharp edges. NEVER use if any parts are mssing or broken. IMPORTANT! Adult assembly is required. TO ASSEMBLE PLAYARD Mattress Wheel (2) Wheel Axle (2) Travel / Storage Bag Retainer (2) Playard Bassinet Metal Support Tubes (2 male, 2 female) Leg (2) Mattress Cap (2) ATTENTION: Parent Organizer* Playard must be fully assembled and securely locked before installing or using other accessories. 1. Unzip bag and remove Playard frame (Fig. 1). Undo the three (3) Fasten straps and set the Mattress aside (Fig. 2). Long Curved Bar (2) Fig. 1 2. Turn the Playard upside down. Short Bar with Connector Knob (2) 3 Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved. Changing Table Fixed Mobile* * Type may vary Fig. 2 Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved. 4 ASSEMBLY ASSEMBLY ATTENTION: Some playard maybe fully assemble. If so, skip to step 5. 3. Attach the Legs to the Playard by pushing each Leg into the bottom of the leg mount until both sides snap firmly into place (Fig. 3). Left leg Fig. 3 Right leg Insert axle from outside IMPORTANT: Check that each Leg is securely attached before use. 4. Attach the Wheels to the Playard using the axles, retainers and caps provided. Align each Wheel and insert axle through the center (Fig. 4). Secure by pushing the retainer over the end of the axle until it snaps into place (Fig.5). Finish by pushing the cap over the end of the axle and retainer until it snaps into place (Fig. 5). 6. Once all four (4) top rails are locked in place, push down on the center handle (Fig. 8). The center mechanism will rotate clockwise 90 degrees and automatically lock in place. IMPORTANT: Test each top rail by pushing down slightly to confirm each is rigid and locked securely in place before use (Fig.9). Fig. 8 ATTENTION: To use as a bassinet, skip to page 9 for bassinet installation instructions. IMPORTANT: Check that each Wheel is securely attached before use. NOTE: To operate the brakes on the Wheels, press downward on the brake levers. To release, lift upward on the lever (Fig. 6) Fig. 4 Outside Fig. 5 Inside 5. Turn the Playard right side up and keep the Legs and Wheels close together. Stretch out top of Playard and pull up one side at a time of each of the top rails until each latch “Clicks” and locks securely into place (Fig. 7). NOTE: The best way to lock the rail(s) is to hold one hand on each side and pull up sharply. (DO NOT pull from the middle where the latch release is located). Fig. 6 5 Fig. 7 Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved. IMPORTANT: The handle located in the center of the Playard floor MUST remain raised (Approx. 45.7 cm or 18 inches) while locking the side rails in place. If the center is not raised the rails will NOT lock. If you experience difficulty and one side of the rail will lock but the other side will not then, unlock the rail by squeezing the release in the center and try again. If you still have difficulty, contact our Customer Service Center at 1-800-328-7363 or visit us online at www.babytrend.com. Fig. 9 7. Place the Mattress on the floor of the Playard with the padded side facing up (Fig. 10) Fig. 10 8. Feed the three (3) hook and loop straps located on the underside of the Mattress through the slots in the floor of each end of the Playard (Fig. 11). Fasten the hook and loop straps to the underside of the Playard floor to prevent the Mattress from moving (Fig. 12). Fig. 11 Fig. 12 Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved. 6 ASSEMBLY WARNING FOLDING PLAYARD Rotate before lifting Fig. 13 1.Undo the three (3) hooks and loop straps holding the Mattress from underneath the Playard floor or remove the Mattress for the Bassinet and set aside. 2. Grasp the center handle, push down and rotate the handle counter-clockwise 90 degrees and lift upward until the handle is as high as the top rails (Fig. 13). Gather the Legs and Wheels together towards the center as close as possible so that they nearly touch (Fig. 14). NOTE: The top rails of the Playard are sill in the “Locked” position. Fig. 14 3.Locate the rail release lever in the center and bottom side of each rail. Lift slightly while squeezing the lever until the rail “Clicks” and releases. Push down each side of the rail while still holding the release lever until both sides are down. Repeat for all remaining sides (Fig. 15). NOTE: If the top rail(s) do not release completely, DO NOT FORCE! Check the floor of the Playard to make sure all the bottom rails are unlocked and make sure the middle handle is pulled up and has not fallen back down. If so, repeat step #3. Fig. 15 4.Gather four (4) corners and center all together tightly (Fig. 16). 5.Wrap Mattress around Playard frame with padded side facing inward. Fig. 16 6.Secure the three (3) hook and loop straps by feeding them through the loops on the end of the Mattress and folding them back onto themselves (Fig. 17). 7 Fig. 17 7.Place folded Playard into carry bag so that the handle comes through the opening between each side of the zipper. Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved. ACCESSORIES WARNING: Failure to follow these warnings and the instructions could result in serious injury or death. FALL HAZARD: To help prevent falls, do not use this product when the infant begins to push up on hands and knees or has reached the height of 25 in. (635 mm), weight of 15 lbs. (6.8 kgs) or 4 months old, whichever comes first. SUFFOCATION HAZARD: Infants can suffocate • In gaps between an extra pad and sides of the bassinet/cradle • On soft bedding Never add a mattress, pillow, comforter, or padding. Use only the pad provided by manufacturer. Never use a water mattress with this product. • To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their back to sleep, unless otherwise advised by your physician. • The playard, including side rails, must be fully erected prior to use. Make sure each latche is secure. • Strings can cause strangulation! NEVER place items with a string around a child's neck such as hood strings or pacifier cords. NEVER suspend strings over bassinet or attach strings to toys. • Discontinue use of the bassinet or the changing table when child begins to push up on hands and knees or has reached the height of 25 in. (635 mm), weight of 15 lbs. (6.8 kgs) or 4 months old, whichever comes first. • NEVER place product near a window where cords from blinds or drapes can strangle a child. • Always provide the supervision necessary for the continued safety of your child. NEVER leave child unattended. • NEVER use plastic shipping bags or other plastic film as mattress covers not sold and intended for that purpose. They can cause suffocation. • Use bassinet with only one child at at time. • NEVER place a child under the bassinet. • NEVER store the bassinet in the playard while in use. • The bassinet must be fully assembled and installed before using. • STRANGULATION HAZARD: NEVER leave the changing table in place when the child is in the bassinet or the playard. Always flip changing table down while not in use. • To prevent your child from falls and other injuries, always use safety belt when child is on the changing table, always stay within arm's reach of your child when using the changing table. • To help prevent heat build-up inside the playard and to avoid overheating your child, when using the bassinet NEVER use an outdoor canopy. Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved. 8 ASSEMBLY ASSEMBLY TO ASSEMBLE BASSINET TO ASSEMBLE CHANGING TABLE Metal Support Tubes (2 male, 2 female) (a) Bassinet ATTENTION: Playard must be fully assembled and securely locked before installing or using the bassinet feature. (See To Assemble Playard section) You will need to remove the mattress from the bottom of the Playard to use inside your Bassinet. 1. Position the Bassinet over and down into the fully assembled Playard. Secure in place by pushing down firmly on each plastic support clip until all are snapped into place (Fig. 18). Fig. 18 Fig. 19 2. Assemble Mattress Support Tubes (if equipped; otherwise, skip to step 4) by inserting the two (2) male tubes into the two (2) female tubes (Fig. 19). 3. Insert both, assembled, Mattress Support Tubes into the loops provided on the bottom of the Bassinet (Fig. 20). 4. Place the Mattress into the Bassinet with the padded side facing upward (Fig. 21) Fig. 20 NOTE: Fasten tabs underneath the Mattress secure it in place. TO REMOVE BASSINET 9 Fig. 21 Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved. 1. Remove Mattress from Bassinet. 2. Remove Canopy. 3. Unsnap all clips and lift Bassinet. (b) (c) WARNING FALL HAZARD: To prevent death or serious injury, always keep child within arm's reach. Always use restraint belt to prevent falls, see page 15 for details. Fig. 22 Contents: (a) 2 Long Curved Bars (b) 2 Short Bar with Connector Knobs (c) 1 Changing Table ATTENTION: Playard must be fully assembled and securely locked before installing or using the changing table feature. (See To Assemble Playard section) Fig. 23 1. Connect the two (2) Long Curved Bars together (Fig. 22). 2. Insert the assembled curved bars into the Changing Table fabric (Fig. 23) Slide the Curved Bars around inside sleeve of the Changing Table. Fig. 24 3. Connect the two (2) Short Bars to each end of the Long Curved Bar (Fig. 24) Make sure that the knobs are both facing down and the same direction on each end. (Fig. 25) Fig. 25 Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved. 10 ASSEMBLY ASSEMBLY 4. Insert Connector Knob Prongs into holes located on both corners of the Playard (Fig. 26). Fig. 26 5. Turn the Connector Knobs counter clockwise to lock into place (Fig. 27). To remove changing table Flip Changing Table to the outside of the Playard. Unsnap fabric flap of Changing Table from Playard. Twist Connector Knobs clockwise to unlock. (Fig. 32) Remove Changing Table from Playard (Fig. 33) and disconnect the Short Bars from the Curved Bar by pressing on the snap buttons and pulling apart. Remove Curved Bar from Changing Table sleeve. Fig. 32 Fig. 33 Fig. 27 6. Flip Changing Table over onto Playard (Fig. 28). 7. Snap the two (2) buttons on the flap down onto the Playard (Fig. 29). Fig. 28 IMPORTANT: Check that the Changing Table is correctly and securely installed BEFORE each use. Fig. 29 To use changing table restraint system Fig. 30 1. Place child on changing table, make sure hand and arms are clear of the restraint. Bring the restraint around the child's waist and clip the male and female ends of the buckle together. (Fig. 30) 2. Tighten strap until fits snug around child's waist. DO NOT OVER TIGHTEN. (Fig. 31) 3. To remove, unsnap the buckle. ATTENTION: 11 PARENT ORGANIZER ASSEMBLY Fig. 31 NEVER use changing table if it is damaged or broken. Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved. or Parent Organizer Diaper Stacker 1. Parent Organizer: Position each hook so that the hooked end is facing the rear side of the organizer. Press the hook down firmly into the slot until it snaps into place. (Fig. 34) Diaper Stacker: Skip to step 2. 2. Connect the Parent Organizer/Diaper Stacker to the Playard by sliding the two (2) connecting clips over an open portion of the top rail of the Playard. (Fig. 35) Fig. 34 NOTE: The Parent Organizer/Diaper Stacker can only be installed on open sides of the Playard where the connecting clips can easily be attached without interfering with other features. Fig. 35 Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved. 12 ASSEMBLY ASSEMBLY MOBILE ASSEMBLY ATTENTION: A crib mobile is intened for visual stimulation and is not intended to be grasped by the child. If attached to the crib or playpen, remove when baby begins to push up on hands and knees. If so designed, mount on wall or ceiling clearly out of a standing baby's reach. Always attach all provided fasteners (strings, straps, clamps, etc.) tightly to a crib or playpen according to the instructions. Check frequently. DO NOT add additional strings and straps to attach to a crib or playpen. DO NOT attach the Mobile with child in Playard or Bassinet. 3. Snap the Mobile Tri-shaped Arm (d) onto the end of the Upper Curved Arm (a, b, c) (Fig. 38). Connect each of the three Toys (e) to the Mobile by threading the string into the slot at the end of each arm. (d) (e) Fig. 38 4. Insert the bottom of the Mobile Arm into the frame of the Playard (Fig. 39). Fig. 39 (c) (a) (d) (b) (a) (b) (e) Contents: (a) 1 Mobile Lower Arm (b) 1 Mobile Arm Holder (c) 1 Mobile Upper Curved Arm (d) 1 Mobile Tri-shaped Arm (e) 3 Toys (toys may vary) Fig. 36 1. Insert the Mobile Lower Arm (a) into the Mobile Arm Holder (b) untill locked together (Fig. 36). (c) (a) (b) 2. Insert the Mobile Upper Curved Arm (c) into the Mobile Lower Arm (a, b) until locked together (Fig. 37). Fig. 37 13 Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved. Copyright © 2007 - 2009, Baby Trend Inc., All Rights Reserved. 14
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement