STEAM CLEANER
WARNING For your own safety, read this user manual
carefully before using the device and keep it for good.
SAFETY INSTRUCTIONS …….….….….…….…..….....1
DESCRIPTION ………………………………...….............8
CHARACTERISTICS ….….….….….….………...…....….9
FILLING ………………....….......…...…...…...…...…...... 9
USE .….….….….….….….….….….….…….....….….….... 12
STORAGE …...…...….....….….…..….….…..….…….…. 14
CLEANING .….….….….….….….….….….….….….….... 15
RECYCLING .….….….….….….….….….….….….…........16
FAQ .….….….….….….….….….…....…….….….….......…17
ASSEMBLY OF ACCESSORIES ......…...…...…..…….....20
TROUBLESHOOTING ...…..…..…..…..….….….….…....22
1
SAFETY INSTRUCTIONS
This electrical appliance produces hot steam from pressurized
water. There are several dangers in case of misuse. To prevent
these dangers and to use the device safely, it is necessary to
observe the instructions and instructions given in this manual.
This device is intended for home use. Do not use in any other way
than described in this leaflet. This device can be used outdoors.
Protection class: IPX4. It should not be stored outdoors, and should
not be exposed to rain, moisture or dew.
Attention: Danger
•Never touch or point the steam to yourself or others!
•The normal operating pressure is within 5 bar/72.5psi. If the
pressure pressure goes over 6.5bar/95psi, the safety valve inside the
filler cap will release steam automatically.
•If excessive steam comes out of the filler cap, turn off the power and
disconnect immediately. Stop using the device. For repair, contact a
qualified technician.
•Never use the device without water in the tank.
•Always cool Steamer for a few minutes before re-adding water.
2
•The fill port must not be opened during use, actually the cap can’t
be opened when there is any pressure inside tank.
•Never operate the appliance without tightening the filler cap
securely.
•Do not overfill the water tank. The suggested maximum capacity of
Steamer is 1.8 L of water. Excessive filling of the water tank may
cause malfunctions, property damage or injury.
•Never return or tilt the Steamer more than 45 ° when it is energized
or if it still produces steam.
•The device does not contain any user-serviceable parts.
•Do not attempt any repairs. Steamer must only be repaired by
qualified electricians. If the power cable is damaged, it must be
replaced by the manufacturer, its customer service department or
similarly qualified persons in order to avoid danger.
• Do not use in the pool of a pool containing water.
WARNING: Danger of burning by hot liquid and steam.
•The temperature of the steam is above 100 ℃; therefore, never
direct it to people, animals or electrical appliances. Never place your
hand in front of the steam outlet of an accessory to check
temperature, proper operation or any other reason.
3
•This device can be used by people with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge if they have
been trained and supervised to use this device safely and understand
the risks. incurred. Children should not play with the device.
•This appliance should not be used by children. Keep the device and
its cable out of the reach of children. Cleaning and maintenance
should not be done by children.
•Steamer is not a toy and should never be used by children.
•Keep hair, loose clothing, fingers, feet, and all body parts away from
the jet of steam.
•Do not use Steamer barefoot or with open shoes or sandals.
•The appliance must not be left unattended when connected to the
mains. Keep the appliance out of the reach of children when it is fed
or cooled.
• Always disconnect Steamer when not in use, left unattended, after
use and before servicing. Stop all controls before unplugging.
CAUTION HOT SURFACE.
The surfaces of the body may become hot during use.
•Please use the handle provided for transport.
•Do not touch the hose that conducts the steam, it becomes hot
during use.
4
DANGER OF ELECTRIC SHOCK.
•Check the condition (wear and defects) of the parts and electrical
cable of the Steamer before each use.
•Plug the Steamer into a grounded mains socket.
•Do not turn on the Steamer if it is damaged. The device must not
be used if it has dropped, if there are visible signs of damage or if
there is a leak.
•Do not pull or carry Steamer through its electrical cable; do not
use the power cable as a handle; do not close a door on the power
cable or pulling on sharp edges or corners.
•Do not expose Steamer, its electrical cable or plug to rain, or
immerse in water or other liquid.
•Do not unplug by pulling on the power cable. To unplug, always
grasp the plug, not the power cable.
•Never use the appliance with a damaged electrical cable.
•Never handle the plug or appliance with wet hands. Do not
immerse the device in water.
• Never use Steamer to clean electrical appliances. Never direct
steam or water to appliances containing electrical components,
such as inside an oven.
5
OTHER PRECAUTIONS
•Keep the power cable away from heated surfaces.
•Do not store or use near flammable materials.
•Do not place Steamer on or under insulation such as blankets,
towels or papers.
•Always store Steamer in a dry place.
•Do not expose Steamer to frost.
•Use only the original Steamer accessories. There is a danger when
using incompatible accessories.
•Store the product indoors, out of reach of children.
•Do not clean this product with water jet. Use a dry or dampened
cloth with soap if necessary.
•Do not use to heat a room.
Risk of serious injury and material damage.
WATER
The suggested maximum capacity of the water tank is 1.8 L of
water. Do not overfill. The steam production time is about 35
minutes under normal conditions of use. The heating time is
about eight minutes for a full tank.
6
STORAGE
Empty the water tank after each use. Do not store Steamer with
water in the tank. Empty, clean and dry before storing. Do not
expose to frost.
FABRICS AND FINISHES
CAUTION: Some fabrics and finishes are not compatible with steam.
Do not use steam on leather, waxed floors, synthetic fabrics, velvet
and other fragile materials. When using steam appliances, always
refer to the manufacturer’s instructions for use and pre-test at a nonvisible location.
GLASS / MIRRORS
WARNING: Never apply steam to windows or mirrors with a
temperature below 0 ° C. Thermal shock resulting from extreme
temperature deviations can break windows and mirrors in case of
contact.
7
DESCRIPTION
1 Steam Handle
2 Steam trigger
3 Steam trigger lock latch
4 Steam Hose
5 Tank filler cap
6 Plug
7 Brush holder
8 Floor Scrub Brush
9 Carry handle
10 Measuring glass
11 Funnel
12 ON / OFF switch
13 Heat Light
14 Extension Tubes
15 Wheel
16 Cloth For Textile Iron
17 Window Squeegee + Textile Iron
18 Round Bristle Brush - Large
19 Round Small Brush - Small
20 Power Jet Tip - Angled
21 Floor Scrub Brush Adapter
22 Small Tip Adapter
23 Floor Scrub Brush Cloth
24 Rotary Brush
8
TECHNICAL CHARACTERISTICS
Steam compartment ……….….. Stainless steel
Temp. Max …………………………. 320℉
Max pressure ………………………. 5bar/72.5psi
Water tank …………………………... 2,0L
Suggested max. capacity............ 1,8L
Power consumption .....…...…..... 2000W
Voltage .....…..…........….....…........... 110-120V~/60Hz
Intensity ..............…...…....…...…..... 15A
Voltage .....…..…........….....…........... 220-240V~/50Hz
Intensity ..............…...…....…...…..... 8,7A
Net weight (empty) ..…..…..….. 3.6 kg
FILLING
Before filling the Steamer with water, turn it off and unplug it. Make
sure there is no more steam by unlocking the steam trigger in the
“on” position.
Always cool Steamer for a few minutes before re-adding water.
9
1 Remove the filler cap by turning
counterclockwise (
only can be
opened without pressure inside tank).
2 Fill the water tank using the funnel and
measuring cup provided. The suggested
maximum capacity of the tank is 1.8 L. Tip:
Do not overfill the tank.
3
Replace the filler cap by turning
clockwise until a good seal is achieved.
CAUTION: If the filler cap is opened too quickly, without taking
the necessary precautions, there is a very high risk of injury. The
metal parts can be extremely hot; avoid contact with the skin. Risk of
burns.
NOTE: The filler cap will not unscrew with pressure inside tank.
10
PRESENTATION
“LOCKED OFF” POSITION
1 Handle Operation.
The steam trigger (2) is located
in the handle and the steam
trigger lock latch is located
under the handle (3). The lock
has two positions: OFF/LOCK and
ON / UNLOCK. Press the front of the
steam trigger lock latch to lock the
steam (A) and LOCK (LOCKED)
press the back to unlock (B) the
steam.
2 Releasing Steam.
“ON/OPERATING” POSITION
When the Heating light (13) goes
out, the Steamer is ready for use
(maximum pressure of 5
bar/72.5psi). Press the steam trigger
lock latch (3) to the ON position (B)
and press the steam trigger (C) to
obtain a steam jet. Release the
11
trigger to stop the jet of steam.
3 After use.
Lock the steam trigger in the OFF position (A) to prevent accidental
operation.
USE OF STEAMER
1) Make sure the Steamer is unplugged and the switch in the OFF
position (12).
2) Unscrew the tank filler cap (5) by turning counterclockwise.
3) Using the measuring cup (10) and the funnel (11), fill the Steamer
with 1.8L of water. (This will produce about 35 minutes of steam.)
4) Replace the filler cap by screwing it clockwise.
5) Attach the extension tubes to the steam handle (1) to obtain a
steam mop or attach the accessory adapter (23).
6) Connect the appliance and press the switch (12) to the ON
position.
7) Two lights come on. The indicator light (12) comes on to Indicate
that the power is turned on. The Heating light (13) comes on to
indicate a rise in steam pressure in the appliance.
8) The appliance is ready for use when the steam Heating light (13)
goes out and the pressure reaches between 4 - 5 bar/ 58 - 72.5psi
depending on the water level in the tank.
12
9) During use, the steam Heating light (13) may turn on again. This
indicates that the steamer is re-heating to supply power.
10) If the pressure drops below 1 bar, the steam flow may not be
sufficient depending on the accessory used. In this case, release
the steam trigger (2) and wait pressure reach again between 4
and 5 bar/ 58 - 72.5psi.
11) When activating the steam trigger (2), water may appear. This is
quite normal because at the beginning, the steam takes a little
time to arrive and the water condenses in the hose and the
extension tubes.
After a few moments the water will turn into steam and there will
be no more cough.
12) When activating the steam trigger (2), a lot of water can flow.
This may be due to a residue of steam from the previous use that
has turned into water. Empty this water by operating the steam
trigger over a bucket or sink. Once this water has passed, you can
use your device quietly.
13) When using the accessories, the surface you are cleaning may be
wet. This is due to the steam that turns into water in contact with this
surface. Provide a sponge or cloth to wipe this surface.
14) After use, press the switch (12) in the OFF position and
disconnect.
13
Be careful, never direct steam on yourself or anyone else
as it may cause burns.
STORAGE
Always empty the Steamer after use. Never leave water in the tank
when storing the unit.
1 Turn off the power by unplugging the Steamer.
2 Empty all remaining tank pressure by pressing the steam
trigger(2).
3 Allow the unit to cool completely (10 minutes minimum).
4 When the appliance is cold, lock the steam trigger and remove
the accessories.
5 Empty all remaining water from the tank by tilting the unit to one
end. Never leave water in the tank when the unit is not in use or
stored.
6 Replace the filler cap and store the Steamer in a safe and dry place.
WARNING: Do not expose Steamer to frost.
DO YOU HAVE HARD WATER?
If the tap water used is very calcareous, it is recommended to use
14
distilled or demineralized water in the Steamer.
If the use of very calcareous water is unavoidable, it is
recommended to clean the water tank regularly.
HOW TO CLEAN THE WATER TANK?
To clean the water tank and descale, proceed as follows.
Do not use detergent to clean the tank.
1 Mix a 50/50 solution of 250 ml of white vinegar and 250 ml of
water. You can use the measuring cup.
2 Pour the solution into the unheated cold tank using the funnel.
3 Leave the solution in the tank for about 30 minutes.
4 After 30 minutes, empty the tank.
5 Repeat steps 1 to 4, if necessary.
6 Rinse well with water.
7 Replace the tank filler cap and store in a safe and dry place.
WARNING: Never clean the water tank while it is still hot.
Always turn off and unplug Steamer before cleaning.
15
DISPOSAL AND RECYCLING
Do not dispose of electrical appliances through household
garbage.
The electrical appliance is in a packaging to prevent any
damage during transport. This packaging is a raw material and can
therefore be reused later or re-introduced into the raw material
circuit. The electric appliance and its accessories are made of several
materials, for example metals and plastics. Eliminate defective
components through the special waste disposal systems. Inquire at a
shop specialized in or in the administration of your municipality!
16
FREQUENTLY ASKED QUESTIONS
Why does water come out of the nozzle?
Steamer generates a large amount of steam that can condense in
water in the hose and extension tubes after a period of no use or
cooling of the unit. Empty this water by operating the steam trigger
over a bucket or sink. Once this water has drained, you can use your
device normally.
No Steam Is Coming Out?
Check the hose is bent or not? if necessary, re-extension. Make sure
that the water tank is not empty.
I can not remove the fill cap?
Make sure the Steamer is completely depressurized. The filler cap is
designed can’t be removed while the unit is still under pressure. To
do this, empty all residual pressure from the tank by pressing the
steam trigger (2). The steam trigger can be unlocked by engaging
the steam trigger lock latch (3) in the ON position. Once the pressure
is discharged from the tank, the filler cap of the tank can be opened.
The steam flow is irregular, the appliance “coughs”.
Slight blockage caused by soil or other foreign matter that can
prevent the flow of steam from arriving continuously. Clean the
17
water tank as shown on page 15.
Can I use boiled water from my tea kettle?
No. Boiled water concentrates the minerals that form the tartar.
Never use pre-soaked water in Steamer.
Can I leave water in the Steamer?
No. Water left in the water tank for a prolonged period may
deteriorate the mechanics of Steamer and deposit limescale. Never
leave water in the Steamer; always empty it after use. If the tap water
used is very hard, it is recommended to use distilled water to
prolong the service life and increase the performance of Steamer.
How do I attach the accessories?
Press the blue button on the handle (1) and insert the extension
tubes or accessories. Make sure the button goes back up to lock the
accessory in position before use. You should normally hear a light
click.
18
Rotating brush (Optional）the
inner
part will rotate due to the high
steam
pressure applied.
Push the rotating brush pipe on the
extension tube until the knob fits correctly in
the oval opening of the rotating brush pipe.
Use the rotating brush to clean all kind off
surfaces with a gentle push and move the
brush in the required direction. The rotating
part will clean the surface.
WARNING: Don’t use the brush towards your face or other parts of
the body. Hot steam is coming out!
19
20
TROUBLESHOOTING
The
device does not heat up.
1 – The device is not connected.
(In the ON position, the power 2 – the device is damaged.
Switch does not light.)
The unit does not heat up.
1 – The steamer is empty.
(The light does not come on
2 – Too much tartar in the tank.
and the power switch is on)
3 – The device is damaged.
The steam flow is irregular,
1 – First use after filling the tank.
the appliance “coughs”.
2 – the level is low.
3 – The steam hose is bent/folded.
4 – Tartar is accumulated in tank.
Water comes out of the
1 – Steam condensed in the hose.
accessories or the head of
2–The water hasn’t been heated enough.
the broom, but no steam.
3 – The water tank is too full.
Steamer generators a large amount of steam that can condense water
in hose, and the extension tubes after use of the device.
The broom head does not
stay attached to the extension
1 - The adapter (22) is not inserted on
the button of tubes.
tubes.
The handle (1) becomes hot.
1 – The handle warms up when steam
passes through.
21
1 – Check the plug / socket.
2 – Disconnect and contact Steamer Technical Support.
1 – Add water by following the instructions on page 10.
2 – Clean the tank by following the instruction on page 15.
3 - Disconnect and contact Steamer Technical Support.
1 – Release the condensed water by pressuring the steam trigger (2,
page 8).
2- Add water by following the instructions on page 10.
3 – Tighten the hose.
4 – Clean the tank according to the instruction on page 15.
1- Direct the tip towards the bucket and unload.
2- Wait for the rise of steam pressure.
3- Turn off the power, allow the unit to cool down and drain the water
from the tank.
Empty the water by operating the steam trigger over a bucket or sink.
1 – Make sure that the spring button is fully engaged in the hole in the
tip.
2- In case of discomfort, you can use a glove.
22
">
