Midland SandRunner 2.9MB Operator Manual

OPERATOR’S MANUAL
Box 249
Rosenort, MB
R0G 1W0
CANADA
Warranty Registration Form
Inspection Report
WARRANTY REGISTRATION
This form must be filled out by the dealer and signed by both the dealer and the customer at the time of delivery.
Customer’s Name:
Dealer’s Name:
Address:
Address:
City:
City:
Province/State:
Province/State:
Postal/Zip Code:
Postal/Zip Code:
Phone Number: (
)
Email:
Trailer Model:
Serial Number:
Delivery Date:
DEALER INSPECTION REPORT
SAFETY
Dump Gate Open/Close Freely
Landing Gear Moves Freely and Crank Stowed
Air Lines Properly Stowed (No Air Leaks)
Electrical Lines Stowed
Tires at Specified Pressure
Wheels Torqued
Brakes Adjusted Properly
Safety Signs/Decals Installed
Manual Supplied
All Reflectors Installed and Clean
All Lights Functioning
Brakes Release at Proper Pressure
I have thoroughly instructed the buyer on the above described equipment which review included the
Operator’s Manual content, equipment care, adjustments, safe operation and applicable warranty policy.
Date:
Dealer’s Rep. Signature:
The above equipment and Operator’s Manual have been received by me and I have been thoroughly
instructed as to care, adjustments, safe operation and applicable warranty policy.
Date:
Owner’s Signature:
WHITE
YELLOW
PINK
MIDLAND
DEALER
CUSTOMER
FOREWORD
The following instructions provide a general description of the proper
procedures which must be considered before starting operations with any
of Midland Manufacturing Limited's dump equipment.
Although the information in this manual was current on the date of issue,
Midland Manufacturing Limited reserves the right to effect changes as the
need occurs without notice or liability.
MIDLAND MANUFACTURING LIMITED
SANDRUNNER TRAILER WARRANTY
Midland Manufacturing Limited (hereafter referred to as “Midland”) warrants directly to you, the first retail
customer; that each new trailer manufactured by Midland is free from defects in material and workmanship;
provided that the trailer is being properly maintained; and that the trailer is being used in it’s normal intended
service free from accident or collision.
Normal service means usage in the manner and for the purpose for which such trailer is generally
manufactured, purchased and utilized; including the loading, unloading, and carriage of uniformly
distributed legal loads of non corrosive cargo, in a manner which does not subject this vehicle to strains,
impacts, and dump cycles greater than normally imposed by lawful use over properly maintained public
roads, with gross vehicle weight, gross axle weights and concentrated loads not exceeding the labeled
gross vehicle weight, gross axle weight and concentrated load ratings (also see "Usage Qualifier" note
below).
The warranty shall (unless otherwise specified) be for the following period following the date of
delivery:
-
Structural components (manufactured by Midland) – one year (conditional / prorated)*
Non-structural components (manufactured by Midland) – one year
Midland does not warrant parts and accessories supplied by others. Midland assigns to the
customer any warranties provided in favor of Midland with respect to any such parts and
accessories; which may be legally assigned by Midland.
* Prorated / Conditional warranty of components manufactured by Midland:
-
Structural components
1st year
- 100% of repair.
-
Non-structural components
One year
- 100% parts and labor.
-
Usage (years) Qualifier:
Midland's warranty may be modified; at Midland's discretion, if said trailer(s) is subjected
to exceptionally heavy use; i.e.: Trailer(s) running 24 hours/day, 7 days a week, or some
similar scenario. Thus, for example, for every year in use; the trailer(s) is considered
to be two (2) or more "usage" years old.
Midland’s warranty will not cover any repairs done without prior discussion;
quotation; and express written approval by Midland
Midland’s warranty coverage does not include:
-
freight (of parts, components, or the trailer)
downtime (loss of income)
other incidental or consequential damages
Midland warranty does not cover:
-
-
Parts that are not defective but which may wear out and have to be replaced; including but
not limited to seals, lights, paint, suspension components, brake system components, brake
linings, brake drums, bushings (suspension, joints, hinges, and knuckles), tires, wood pieces
and the like.
Alignments or adjustments which are normal maintenance items; not caused by a defect in
any components or in the trailer.
Any trailer or component of a trailer that has been altered (other than by Midland) in any way
so as in the judgement of Midland; to affect its operation or reliability, or which has been subject
to misuse, neglect or accident.
Warranty claims:
ON ANY REPAIRS UNDER WARRANTY, MIDLAND MUST BE CONTACTED AND OUR APPROVAL
RECEIVED IN THE FORM OF A WARRANTY PURCHASE ORDER BEFORE ANY WORK IS DONE.
THE PURCHASER CLAIMING UNDER THIS WARRANTY SHALL SUBMIT A WARRANTY CLAIM IN
THE PRESCRIBED FORM TO MIDLAND OR AN AUTHORIZED DEALER FOR INSPECTION BY AN
AUTHORIZED COMPANY REPRESENTATIVE.
1) We will not accept warranty bills under any circumstances that have not received our prior authorization
(including a warranty authorization number); based on a written quotation for the required repair work.
2) We are to supply all warranty parts unless agreed otherwise.
3) Any invoices covering warranty parts and / or labor that we consider excessive will be paid on the
basis of our cost of such parts and / or labor as if the work had been done at our factory.
4) No warranty on parts will be paid for until the faulty parts have been returned prepaid, for our inspection,
unless agreed otherwise.
Midland will not be responsible for freight for returned parts except by prior arrangement and written
authorization.
5) All invoices submitted, requesting warranty, must show the number of hours of labor and the rate being
charged.
6) Midland must receive notice of a defect immediately after such defect is discovered and at the request
of Midland or an authorized agent return the trailer to Midland or an authorized agent or other agreed
upon location within 20 days after the trailer return is requested. Note: Warranty consideration may be
influenced by "when a defect ought to have been discovered under normal circumstances"; in cases
where the defect notification is not made in a timely manner.
7) Transportation expenses to and from a repair facility are the responsibility of the trailer owner.
WARRANTY DISCLAIMER AND LIMITATIONS OF LIABILITY:
Except for the above warranty, Midland makes no other express warranties and HEREBY EXCLUDES
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE.
IT IS AGREED THAT MIDLAND SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM ANY BREACH OF WARRANTY including, but not limited to, loss of
income, damage to vehicle, attachments, trucks or cargo, towing expenses, or injury to or death of persons.
No person is authorized to give any warranties or to assume any other liability on Midland’s behalf unless
made and assumed in writing by Midland and signed by an officer of Midland.
TIME LIMIT ON COMMENCING LEGAL ACTION:
While Midland undertakes to make reasonable efforts to resolve every warranty claim, if Midland does
not accept as valid all or any part of a particular claim, then Midland will only be responsible under this
warranty for such claim if it is enforced by legal action commenced within one year from the date that the
breach of warranty occurred.
WARRANTY TRANSFER:
Warranty transfers to a second owner will be recognized provided:
-
the said transfer takes place in the first twelve (12) months of service
the said trailer is fully inspected and approved by Midland by way of a personal inspection by
an authorized Midland agent
a new warranty form is filled out and sent to Midland Manufacturing Limited immediately upon
close of the transaction. (New Equipment Warranty forms are available from Midland).
the second warranty form must be returned to Midland showing name of original purchaser
and date the trailer was put into service as well as the date and name of the new owner. Any
and all warranty periods are begun on the date of sale of the new trailer to the original retail
customer.
OPERATORS MANUAL:
The purchaser acknowledges having received training in the safe operation of the trailer unit and
further acknowledges that Midland does not assume any liability resulting from the operation of
the trailer unit in any manner other than described in the operator’s manual supplied at the time
of purchase.
THIS AGREEMENT IS NOT VALID UNLESS A SIGNED COPY OF THE WARRANTY
REGISTRATION FORM IS RECEIVED BY MIDLAND WITH 15 DAYS OF DATE OF DELIVERY;
TO THE FIRST RETAIL CUSTOMER.
Midland Manufacturing Limited
Box 249
Rosenort, Manitoba R0G 1W0
COMPLIANCE PLATE LOCATION
The trailer compliance plate is mounted where indicated on the trailer, verifying compliance with all applicable
Canadian and United States Motor Vehicle Safety Standards and discloses the Gross Vehicle Weight Rating
(GVWR) and Gross Axle Weight Rating (GAWR). This plate also has the trailer Serial Number recorded and the
date of manufacture.
1. V.I.N.
Vehicle Identification Number.
2. GROSS AXLE WEIGHT RATING (GAWR)
Gross axle weight rating is the "rated capacity at the tire-ground interface" and is to reflect the "weakest
link" in the entire suspension system, whether it be springs, axles, wheels, rims or tires.
3. GROSS VEHICLE WEIGHT RATING (GVWR)
The GVWR for semi-trailers is the sum of the trailer tare weight, and that uniformly distributed payload which
will result in a suspension load at the tire-ground interface equal to the sum of the trailer's gross axle weight
rating (GAWR) with a limitation imposed by practical or structural considerations.
BOX 249
ROSENORT, MANITOBA
CANADA
R0G 1W0
PHONE: 204-746-2348
www.midlandtrailers.com
V.I.N. PLATE LOCATION
Always give your dealer the V.I.N. (Vehicle Identification Number) of your Midland SandRunner Trailer unit when
ordering parts or requesting service or other information.
The plate is located where indicated. Please mark the number in the space provided for easy reference. Also
obtain and mark down the Model Number, Production Year and other pertinent information of your Trailer unit in
the spaces provided.
SERIAL NUMBER LOCATION
V.I.N. Number
Model Number
Length
Suspension
Axles
Wheels
Tires
Date Purchased
Dealer Purchased From
Address
TABLE OF CONTENTS
SECTION
DESCRIPTION
1
2
PAGE
Introduction ..........................................................1
Safety ....................................................................2
General Safety........................................................3
Operating Safety ....................................................4
Maintenance Safety ...............................................4
Travel Safety ...........................................................5
Loading Safety .......................................................5
Tire Safety ..............................................................5
Safety Signs ...........................................................5
Air Safety ................................................................5
Sign-Off Form ........................................................6
Safety Sign Locations ..........................................7
Operation Guidelines .........................................11
To the New Operator or Owner ............................11
Terminology ..........................................................12
Break-In................................................................13
Controls ................................................................15
Pre-Operation Vehicle Inspection Procedure .......17
Hooking Up/Unhooking .......................................20
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3
4
4.1
4.2
4.3
4.4
4.5
4.6
4.6.1
4.6.2
4.7
4.8
Hooking Up .......................................................................... 20
Unhooking ............................................................................ 22
Discharge Gates ...................................................23
Air System ............................................................24
4.8.1
4.9
4.10
Tanks .................................................................................... 24
Loading/Unloading ...............................................25
Transporting .........................................................26
4.10.1
4.10.2
4.10.3
Operating Instructions.......................................................... 26
Braking Guidelines ............................................................... 27
Tires ..................................................................................... 28
TABLE OF CONTENTS
SECTION
DESCRIPTION
5
Service and Maintenance ..................................29
Service .................................................................29
Fluids and Lubricants ...........................................29
Greasing ...............................................................29
Servicing Intervals ................................................30
Service Record Summary (Lubrication) ...............38
Periodic Maintenance and Adjustments ..............39
Torque Specification Summary ............................39
Kingpin and Oscillating Fifth Wheel Plate ............41
Fifth Wheel ...........................................................42
Axle Alignment .....................................................43
Wheel Hubs/Bearings ..........................................45
Wheels .................................................................49
Tires......................................................................51
Brakes ..................................................................53
Slack Adjusters ....................................................56
Trailer ABS............................................................63
Air Chamber/Spring Brake ...................................64
Suspension System .............................................65
5.1
5.1.1
5.1.2
5.1.3
5.1.4
5.2
5.2.1
5.2.2
5.2.3
5.2.4
5.2.5
5.2.6
5.2.7
5.2.8
5.2.9
5.2.10
5.2.11
5.2.12
5.2.12.1
5.2.13
6
7
7.1
8
Air Ride Suspension ............................................................. 65
Air System ............................................................68
5.2.13.1
5.2.13.2
5.2.14
PAGE
Air System Inspection .......................................................... 68
Air System Function ............................................................. 68
Electrical System..................................................69
Trouble Shooting ................................................70
Specifications .....................................................78
Bolt Torque ...........................................................78
Index ....................................................................79
1
INTRODUCTION
Midland appreciates having you for our customer and trust this unit will give you many years of trouble-free use.
We are pleased to have you join a growing number of operators pulling Midland trailers.
We take pride in building products to meet the demands of a discriminating buyer in a variety of industries;
transportation industry, mining, oil field, paving, aggregate hauling, and excavation. We have sought to
anticipate your needs with respect to safety, convenience, design and engineering of your unit. Midland
provides information and service support to its customers through its distributor and dealer network. Contact
them should you need assistance.
Safe, efficient and trouble free operation of your Midland Trailer requires that you and anyone else who will
be operating or maintaining the Trailer, read this manual carefully and understand the Safety, Operation,
Maintenance and Trouble Shooting information contained within the Operator's Manual. Failure to read and
follow instructions in the manual could lead to costly repairs; and even more importantly could lead to serious
injuries and possibly death.
This manual covers the Midland SandRunner.
Although some of the diagrams and pictures may
not apply to all trailers, we have tried to show details
of common adjustments and features that are on
standard production units.
Use the Table of Contents or Index as a guide in
locating the specific information applicable to your
Trailer. Keep this manual handy for frequent reference
and to pass on to new operators or owners.
OPERATOR ORIENTATION - The directions left and
right as mentioned throughout this manual, are taken
as if the operator was standing behind the trailer
facing forward.
1
2
SAFETY
SAFETY ALERT SYMBOL
This Safety Alert symbol means
ATTENTION! BECOME ALERT!
YOUR SAFETY IS INVOLVED!
The Safety Alert symbol identifies
important safety messages on the
Midland Trailer and in the manual.
When you see this symbol, be alert
to the possibility of personal injury
or death. Follow the instructions in
the safety message.
Why is SAFETY important to you?
Accidents Disable and Kill
Accidents Cost
Accidents Can Be Avoided
3 Big Reasons
DANGER: Indicates an imminently hazardous
situation that, if not avoided, will result
in death or serious injury. This signal
word is to be limited to the most
extreme situations, typically for machine
components that, for functional
purposes, cannot be guarded.
SIGNAL WORDS:
Note the use of the signal words DANGER,
WARNING and CAUTION with the safety
messages. The appropriate signal word for
each message has been selected using the
following guide-lines:
WARNING: Indicates a potentially hazardous
CAUTION:
situation that, if not avoided, could
result in death or serious injury, and
includes hazards that are exposed
when guards are removed. It may
also be used to alert against unsafe
practices.
Indicates a potentially hazardous
situation that, if not avoided, may result
in minor or moderate injury. It may
also be used to alert against unsafe
practices.
2
SAFETY
YOU are responsible for the SAFE operation and
maintenance of your Midland Trailer. YOU MUST
ensure that you and anyone else who is going to
operate, maintain or work around the Trailer be
familiar with all the operating and maintenance
procedures and related SAFETY information
contained in this manual.
Remember, YOU are the key to safety. Good safety
practices not only protect you but also the people
around you. Make these practices a working part
of your safety program. Be certain that EVERYONE
operating this equipment is familiar with the
recommended procedures and follows all the safety
precautions. Remember, most accidents can be
prevented. Do not risk injury or death.
•
Remember, you are not just a driver; you are
expected to be an effective and efficient operator.
•
Trailer owners MUST give operating instructions
to operators or employees before allowing
them to operate the equipment or doing any
maintenance work on the trailer, and at least
annually thereafter.
•
The most important safety device on this
equipment is a SAFE operator. It is the operator’s
responsibility to read and understand ALL Safety
and Operating instructions in the manual and to
follow these. All accidents can be avoided.
•
Midland feels that a person who has not read,
understood and been trained to follow all
operating and safety instructions is not qualified
to operate or do any maintenance work on the
equipment. An untrained operator exposes
himself and bystanders to possible serious injury
or death.
•
•
DO NOT modify the equipment in any way.
Unauthorized modification may impair the
function and/or safety of the equipment and
affect Trailer life.
2.1
GENERAL SAFETY
1. Read and understand the
Operators Manual and all
safety signs before operating,
maintaining or adjusting the
Trailer.
2. Only trained competent persons shall operate
the Trailer. An untrained operator is not
qualified to operate the unit.
3. Have a first-aid kit available for
use should the need arise and
know how to use it.
4. Do not allow riders on any part of the
trailer.
5. Have a fire extinguisher available for
use should the need arise and know
how to use it.
6. Wear appropriate protective gear. This list
includes but is not
limited to:
- A hard hat
- Protective shoes
with slip resistant
soles
- Heavy gloves
7. Place all controls in neutral, stop truck engine,
set park brake, remove ignition key and wait for
all moving parts to stop and all air pressure to
be fully exhausted before servicing, adjusting or
repairing.
8. Do not drink and drive.
Think SAFETY! Work SAFELY!
3
2.2
OPERATING SAFETY
2.3 MAINTENANCE SAFETY
1.
Read and understand all of the Operator’s Manual
and all safety signs before operating or adjusting the
Midland Trailer.
1.
Read and understand all the information in the
Operator’s Manual regarding maintenance,
adjusting and servicing the Trailer unit.
2.
Do not allow riders on any part of the trailer.
2.
3.
Drive very carefully when negotiating hilly or uneven
terrain.
4.
Keep hands, feet, clothing and hair away from all
moving parts.
Place all controls in neutral, stop the truck
engine, remove ignition key, set the park brake,
and exhaust all air pressure from trailer air system
before adjusting, servicing or maintaining any part
of the Trailer unit.
3.
Follow good shop
practices:
Keep service
area clean and dry.
Be sure electrical
outlets and tools are
properly grounded.
Use adequate light for
the job at hand.
4.
Cage spring brake
chamber before
disassembling.
5.
Block wheels before de-activating brakes.
6.
Maintain fasteners in running gear systems at
their specified torque at all times.
7.
Establish and maintain a Trailer Preventative
Maintenance (TPM) program on your equipment.
Some jurisdictions require this program and the
maintenance of records on every commercial
vehicle on the road for future reference.
5.
Place all controls in neutral, stop the engine, set
park brake, remove ignition key and wait for all
moving parts to stop and all air pressure to be fully
exhausted before servicing, adjusting, repairing or
maintaining.
6.
Stay away from discharge gates when truck engine
is running and/or the air system is pressurized.
Keep others away.
NOTE: The locking pin is NOT designed to hold the
gates in the open position under air pressure
7.
8.
9.
Maintain king pin, fifth wheel assembly and all
running gear in good condition at all times.
Clear the area of all bystanders, especially children,
before starting up and operating the tractor and
trailer.
Make sure that all lights and reflectors that are
required by the local highways and transport
authorities are in place, clean and can be seen
clearly by all overtaking and oncoming traffic.
10. Do not operate unit with spring brakes caged or
brakes disabled. Block wheels if unhooked.
11. Before disconnecting the tractor from the trailer
unit(s) make sure that the tractor and trailer are on
level ground and that the trailer wheels are securely
blocked. Lower landing gear and provide extra
support if the ground is soft. Do not unhook if trailer
is loaded.
12. Do not dump unless the trailer is on firm level
surface; with all wheels in contact with that firm level
surface
13. Review safety items with all personnel annually or
more frequently as necessary.
4
2.4
TRAVEL SAFETY
2.7
SAFETY SIGNS
1. Read and understand all the information in the
operator’s manual regarding procedures and
safety when operating the Trailer unit in the field
or on the road.
1. Keep safety signs clean and legible at all times.
2. Make sure all the lights and reflectors that are
required by the local highway and transport
authorities are in place, are clean and can be
seen clearly by all overtaking and oncoming
traffic.
3. Replaced parts that displayed a safety sign
should also display the current sign.
3. Drive carefully and defensively at all times and
especially when negotiating uneven or hilly
terrain.
4. Do not allow riders on any part of the trailer.
5. Make sure you are in compliance with all local
regulations regarding transporting on public
roads and highways. Consult your local law
enforcement agency for further details.
2.5
2. Replace safety signs that are missing or have
become illegible.
4. Safety signs damaged or removed, available at
no extra charge. Contact your dealer or factory.
How to Install Safety Signs:
•
Be sure that the installation area is clean and dry.
•
Be sure temperature is above 50°F (10°C).
•
Decide on the exact position before you remove
the backing paper.
•
Remove the smallest portion of the split backing
paper.
•
Align the sign over the specified area and
carefully press the small portion with the exposed
sticky backing in place.
•
Slowly peel back the remaining paper and
carefully smooth the remaining portion of the sign
in place.
•
Small air pockets can be pierced with a pin and
smoothed out using the piece of sign backing
paper.
LOADING SAFETY
1. Do not drop load into trailer to prevent damaging
sides or bottom.
2. Use common sense when loading material
containing large rocks or frozen chunks to
prevent damaging gates and hoppers.
3. Do not exceed total load carrying specifications
for trailer.
2.6
TIRE SAFETY
1. Failure to follow proper procedures when
mounting a tire on a wheel or rim can produce
an explosion which may result in serious injury or
death.
2.8
AIR SAFETY
1. Make sure that all air system related components
are checked regularly and maintained in good
condition.
2. Replace any worn, cut, flattened or crimped
hoses on air lines and fittings.
2. Do not attempt to mount a tire unless you have
the proper equipment and experience to do the
job.
3. Have a qualified tire dealer or repair service
perform required tire maintenance.
5
2.9
SIGN-OFF FORM
Midland follows the general Safety Standards specified by the Society of Automotive Engineers (SAE) and the
Occupational Safety and Health Administration (OSHA). Anyone who will be operating and/or maintaining the
Midland Trailer must read and clearly understand ALL Safety, Operating and Maintenance information presented
in this manual.
Do not operate or allow anyone else to operate this equipment until such information has been reviewed and
understood. Annually, or more often as needed, review this information with all personnel.
Make these periodic reviews of SAFETY and OPERATION a standard practice for all of your equipment.
A sign-off sheet is provided for your record keeping to show that all personnel who will be working with the
equipment have read and understand the information in the Operator’s Manual and have been instructed in the
safe operation of the equipment.
SIGN-OFF FORM
DATE
6
EMPLOYEE'S SIGNATURE
EMPLOYER'S SIGNATURE
3
SAFETY SIGN LOCATIONS
The types of safety signs and locations on the equipment are shown in the illustration below. Good safety
requires that you familiarize yourself with the various safety signs, the type of warning and the area, or particular
function related to that area, that requires your SAFETY AWARENESS.
• Think SAFETY! Work SAFELY!
REMEMBER - If safety signs have been damaged, removed, become illegible or parts replaced without signs,
new signs must be applied. New signs are available from your authorized dealer.
7
The types of safety signs and locations on the equipment are shown in the illustration below. Good safety requires that you familiarize yourself with the various safety signs, the type of warning and the area, or particular
function related to that area, that requires your SAFETY AWARENESS.
• Think SAFETY! Work SAFELY!
REMEMBER - If safety signs have been damaged, removed, become illegible or parts replaced without signs,
new signs must be applied. New signs are available from your authorized dealer.
8
The types of safety signs and locations on the equipment are shown in the illustration below. Good safety requires that you familiarize yourself with the various safety signs, the type of warning and the area, or particular
function related to that area, that requires your SAFETY AWARENESS.
• Think SAFETY! Work SAFELY!
REMEMBER - If safety signs have been damaged, removed, become illegible or parts replaced without signs,
new signs must be applied. New signs are available from your authorized dealer.
9
The types of safety signs and locations on the equipment are shown in the illustration below. Good safety requires that you familiarize yourself with the various safety signs, the type of warning and the area, or particular
function related to that area, that requires your SAFETY AWARENESS.
• Think SAFETY! Work SAFELY!
A
B
C
D
E
F
H
G
I
J
K
L
M
N
O
P
S
T
Q
REMEMBER - If safety signs have been damaged, removed, become illegible or parts replaced without signs,
new signs must be applied. New signs are available from your authorized dealer.
10
4
OPERATION GUIDELINES
B
OPERATING SAFETY
1. Read and understand all the Operator’s
Manual and all safety signs before operating
or adjusting the Midland Trailer.
9. Maintain king pin, fifth wheel assembly and
all running gear in good condition at all
times.
2. Do not allow riders on any part of the trailer.
10. Clear the area of all bystanders, especially
children, before starting up and operating
the tractor and trailer.
3. Drive very carefully when negotiating hilly or
uneven terrain.
4. Keep hands, feet, clothing and hair away
from all moving parts.
5. Place all controls in neutral, stop the engine,
set park brake, remove ignition key and wait
for all moving parts to stop before servicing,
adjusting, repairing or maintaining.
6. Stay away from discharge gates. Keep
others away.
7. Use care when manually operating discharge
gates. Always know where your operating
partner is before moving gates to prevent
injury.
8. Disconnect air lines and exhaust system
before working on discharge gates. Do not
enter or reach into trailer unless you know
that the air system is completely exhausted
and the gates cannot close.
11. Make sure that all lights and reflectors that
are required by the local highways and
transport authorities are in place, clean and
can be seen clearly by all overtaking and
oncoming traffic.
12. Do not operate unit with spring brakes
caged or brakes disabled. Block wheels if
unhooked.
13. Before disconnecting the tractor from the
trailer unit(s) make sure that the tractor and
trailer are on level ground and that the trailer
wheels are securely blocked. Lower landing
gear and provide extra support if the ground
is soft. Do not unhook if trailer is loaded.
14. Do not dump unless vehicle is on firm level
surface.
15. Review safety items with all personnel
annually.
1812428
4.1
TO THE NEW OPERATOR OR OWNER
The Midland SandRunner Trailers combine light
weight construction methods and high strength
materials to become a safe, reliable and efficient
sand hauling unit. Be sure to familiarize yourself with
the Trailer by reading this Operator’s Manual and the
Safety Alerts before attempting to operate it. With
careful use and a good maintenance schedule, the
unit will give many years of trouble-free use.
It is the responsibility of the owner and operator
to be familiar with the weight and loading of your
trailer or combinations of trailers. Trailer weight
and loading vary from jurisdiction to jurisdiction.
Be familiar with yours and any that you will be
travelling through.
11
4.2
TERMINOLOGY
The Midland SandRunner Trailers are designed with clam
shell type discharge gates that are orientated perpendicular
to the direction of travel. Trailers are available in a B-Train
design. Some of the standard features are shown.
A
B
C
D
E
F
Tridem
Tandem
Clam Hopper
Manual Roll Tarp
Two-Speed Landing Gear
Ladder
Fig. 1
12
PRINCIPLE SYSTEMS
4.3
BREAK-IN
Break-in is the most important time in a Trailer's life.
It is critical that the unit be checked frequently during
the first 5000 miles to be sure that all components
and systems are properly adjusted and performing as
required.
The following inspection schedule is provided as a
guide for normal operating conditions. More frequent
inspections are recommended in severe or extreme
conditions.
Inspect at:
50-100 miles, 1-2 hours
500 miles, 8-10 hours
1500 miles, 25-30 hours
5000 miles, 100 hours:
1. Brakes
It takes a few weeks of operation for the brake
shoes to mate with the drum contour and
burnish the surface. The operator should check
the brakes every day. Check the function and
adjustment of the brakes on each axle. All brakes
should apply evenly. No shoes should drag on
the drum when the brakes are not applied.
2. Tires
Tires are designed to provide maximum life and
performance when maintained at their specified
inflation pressure. Although the tires are inflated
to their specified pressure at the factory, the
pressure can change before going into service.
Always use an accurate gauge to check the
pressure when the tire is cold.
3. Wheels/Rims
Although lug bolts and rim fasteners are always
tightened to their specified torque at the factory,
it is normal for them to lose some of their torque
during the first few miles of operation. After
the first 50 miles; retorque lug bolts and rim
fasteners. Then go to the retorquing interval
defined in the Maintenance section of every
25,000 miles. Keep all fasteners tightened to
their specified torque to prevent damaging any
components.
4. Axles
Each wheel bearing is assembled at the factory
with the required pre-load (refer to Section
5.2.4). This pre-load should be checked to insure
proper axle and bearing function. Check the
temperature of the hub by hand after 10 to 15
miles (15 to 25 km) during the first trip. A hot
hub must have the bearing pre-load reset before
continuing.
Jack the axle up and support it on a stand. Turn
the wheel by hand. The wheel should turn freely.
If it does not, check if the brakes are dragging or
if the bearing has too much pre-load. If either of
these conditions exist, correct before proceeding.
Move the wheel laterally on the axle shaft. If the
wheel wobbles, the bearing has lost its preload. Tighten bearing and set pre-load before
continuing.
5. Hub Oil Levels:
Oil bath hubs are used on all trailers and are filled
at the factory. Check hubs frequently (at least
daily) during the first few weeks of operation.
Always check when the oil is cold and the trailer
is on the level. Use the level mark on the hub
face when checking oil level. Replace seals and
gaskets if hub has an oil leak. Do not operate
without oil in the hub.
Whenever a wheel is removed from an axle, the
above retorquing procedure must be followed
to be sure that the wheel is secured to the axle.
If any component is damaged due to loose
fasteners, it will have to be replaced.
13
4.3
BREAK-IN (cont'd)
6. Suspension
A suspension system connects the axles to the
frame. All fasteners must be maintained at their
specified torque to ensure that all clamping and
anchoring forces remain intact. If these forces
are not maintained, components can shift or
move and affect the performance and component
life. Refer to Maintenance Section for the list
of required torque values for all fasteners in
suspension system. Any loosening can lead
to component shifting, misalignment and/or
twisting. Any of these items can cause erratic
handling, broken components or rapid tire wear.
Always tighten the nut end of fastener. Specified
torque values apply only to nut end torquing.
7. Axle Alignment
Axle alignment is properly set at the factory
when the unit is new and will remain aligned
unless fasteners loosen or components wear or
if the tire/axle combination of the trailer take a
severe hit; ie: a curb, rock or other obstruction.
Use a steel measuring tape to check the
alignment. Refer to Maintenance Section for
alignment checking procedure. Axles that are
out of alignment can cause erratic handling
characteristics, broken components and
accelerated tire wear.
8. Fifth Wheel Assembly Components
The king pin, anchor plate and upper and lower
fifth wheel assemblies must be inspected to
check for mechanical integrity of all components.
All components and systems must be kept in
good condition to safely and reliably transmit the
accelerating, braking and side loads between the
trailer, fifth wheel and towing vehicle.
a. King Pin:
Check the king pin for cracks, chips, or
whether it is bent. Check that there are
no cracks or distortions between the king
pin and its anchor plate. If any defects are
found, replace the king pin and its anchor
plate before resuming work.
14
b. Oscillating Plate:
Check the rubber bushings and anchor bolt
torque on the oscillating plate on a regular
basis. Replace the bushings if they are
cracked, distorted or loose in their mounts.
Retorque the nut on the anchor bolts.
Check the plate frame for cracks, bends or
distortions. Replace oscillating plate if any of
these conditions are found.
c. Fifth Wheel Assembly:
The fifth wheel assembly consists of the
king pin locking mechanism, surface plate,
frame, pivot and anchor system. Check that
the king pin locking mechanism locks and
unlocks easily and that all moving surfaces
are coated with grease. Check that the
surface plate is clean and coated with grease.
Check the surface plate, pivot and anchor
frame for cracks, bends or distortions.
Replace any damaged components.
Retorque fasteners to maintain the proper
clamping forces on all components. Loose
fasteners can cause components to move
or bend and create mechanical or safety
problems during operation.
9. Electrical and Air Lines
Electrical and air lines extend from the front of the
unit to each light and air operated component.
Although they are all anchored along their routing
pathways from the factory, they occasionally do
come loose and will sag. Inspect all electrical
and air lines. Use plastic ties to secure line to
frame if any are loose and sag. Replace if any
are pinched, kinked, cut or abraded. Extra care
should be taken in cold or extreme operating
conditions. Ice, mud or brush can pull lines loose
from their anchors and cause damage. Clean
components, repair damage, re-anchor and
install protectors if appropriate. Do not operate
with damaged components.
4.4
CONTROLS (cont'd)
Before starting to work, all operators
should familiarize themselves with the
location and function of the controls.
1. Tank Drain Valve:
Every air reservoir tank on the trailer is
equipped with a spring-loaded valve
that is used to drain the moisture.
These valves are attached to a cable
that extends out to the frame to allow
the operator to drain moisture from the
tanks. Pull on the cable to open the
valve and drain the moisture from the
tank. Release the cable to close the
valve.
Fig. 2
DRAIN VALVE CABLE
15
4.4
CONTROLS (cont'd)
2. Landing Gear:
This landing gear uses a crank
to set the position of the landing
gear height. Pull the crank from
its stowed position, mount on the
driveshaft and push in to lock.
For the high ratio drive, push the
handle and driveshaft in as far as
it will go. For the low ratio drive,
pull the handle and shaft as far out
as it will go.
When changing drive ratios, it may
be necessary to turn the crank
slightly to align the gears. Turn the
crank clockwise to lower the legs.
Place pads under the legs in soft
conditions.
Perform all procedures in lighted
area clear of obstacles and other
personnel. Always grip the crank
handle securely with both hands.
Maintain proper footing at all
times. Never attempt to shift the
landing gear while under load.
Lifting and lowering of the trailer
must always be done in low gear.
Do not attempt to lift or lower
trailer with landing gear in high
gear, as serious personal injury
could occur. Place pads under
the legs in soft conditions. Always
secure the crank handle when not
in use.
16
Fig. 3
LANDING GEAR
4.5
PRE-OPERATION VEHICLE
INSPECTION PROCEDURE
The safe and trouble-free use of a Midland Trailer
requires the operator to maintain the unit in good
operating condition. To assist the operator, a preoperation checklist is provided that should be
followed each time before the trailer is used.
NOTE
The tractor items, part of the
Department of Transport
(D.O.T.) walk around sequence,
have been omitted.
WALK AROUND SEQUENCE
Step 1 - Trailer Frontal Area
1. Air and Electrical Connections
a. Glad hands properly mounted, free of
damage, not leaking and not worn.
b. Electrical line receptacle properly mounted,
free of damage, plug adequately seated and
safety catch engaged to prevent accidental
disconnection.
c. Air and electrical lines properly secured to
avoid tangling, snagging and chafing with
sufficient slack for turns.
2. Lights and Reflectors
a. Clearance, turn and identification lights should
be clean, operational and proper colour.
b. Reflectors and conspicuousy tape clean and
proper color.
Step 2 - Coupling System Area
1. Fifth Wheel (Lower)
a. Securely mounted to frame.
b. No missing or damaged parts.
c. No visible space between upper and lower
fifth wheel.
d. Locking jaws around the shank and not the
head of Kingpin.
e. Release lever properly seated and safety
latch lock engaged.
2. Fifth Wheel (Upper)
a. Kingpin not worn, bent or damaged.
b. Oscillating plate not cracked, bent, worn or
damaged.
c. Oscillating bushing in good condition.
Fig. 4
WALKAROUND SEQUENCE
17
3. Air and Electric Lines Visible From This Point
a. Should be secure from dangling, snagging
and chafing.
2. Tandem or Tridem
a. Repeat wheel and tire inspection as above.
b. Flexible air lines not cracked, cut, crimped
or otherwise damaged, secured against
tangling, dragging or chafing.
b. Should be free from damage and clean.
Step 3 - Right of Trailer Area
1. Front Trailer Support (Landing Gear)
a. Fully raised and secured, no missing parts,
not bent or otherwise damaged.
3. Suspension
a. Air:
Condition of air bag(s) axle clamping bolts,
pivot arm and height control valve.
b. Crank handle present and secured (typically
on left side).
2. Spare Tires
a. Carrier or rack not damaged.
b. Tire and/or wheel securely mounted in the
rack.
b. Axle alignment.
c. Retorque all fasteners.
Step 5 - Brakes
1. Brakes
a. Condition of brake drum(s).
c. Tire and wheel condition adequate. Proper
spare tire size, correctly inflated.
b. Condition of hoses, lines and valves.
c. Check slack adjusters.
3. Lights and Reflectors
a. Trailer side clearance lights clean, operational
and proper color.
d. Check air chamber mounting.
e. Check spring brakes (if so equipped).
b. Reflectors and conspicuousy tape clean and
proper color.
4. Frame and Body
a. Frame and cross members not bent, cracked,
damaged or missing.
b. Body parts not damaged or missing.
5. Discharge Gate(s)
a. Gate stops in position and secure.
f.
Step 6 - Rear of Trailer
1. Lights and Reflectors
a. Clearance, turn, back-up, work and
identification lights, clean and operational and
proper color.
Step 4 - Right Rear Trailer Wheel Area
1.
Dual Wheels
a. Condition of wheels and rims; no cracked or
bent rims, broken spacers, studs, clamps or
lugs.
b. Condition of tires; properly inflated, valve
stems not touching wheel rims or brake
drums, valve caps in place, no serious cuts,
bulges, tread wear or any signs of
misalignment and no debris stuck between
the tires.
c. Tires all to be the same type e.g. do not mix
radial and bias types on the same axles.
d. Wheel bearings and hub; no obvious oil leaks.
e. Mud flaps in place and in good condition.
18
Drain moisture from air tank with cable.
2.
b.
Reflectors and conspicuously tape clean and
proper color.
c.
Tail-lights clean, operating and proper color.
Check “B” train 5th wheel:
Repeat same as Step 2 “Coupling System
Area”.
Repeat same as Step 2 “Coupling System Area”.
Step 7 - Left Rear Trailer Wheel Area
Check all items as done on right side (Step 4
"Right Rear Trailer Wheel Area").
Step 8 - Left Side of Trailer Area
1. Check all items as done on right side (Step 3
"Right of Trailer Area").
Step 9 - Trailer(s) Functional Check
(Tractor Attached)
1. Check for proper connection of the air brake
glad-hands and secure contact of electrical
connection.
2. Start engine.
3. Build up air pressure in the tractor-trailer systems.
4. Turn on lights and inspect for proper function of:
a.
b.
c.
d.
e.
f.
g.
Clearance lights.
Identification lights.
Turn signals and 4-way flasher.
Sidemarker lights.
Tail lights.
Stop lights.
Work lights.
5. Check the function of brakes.
a.
b.
c.
d.
Apply service brakes.
Apply parking brakes.
Apply emergency brakes.
Stop engine.
i.
ii.
Release trailer emergency brakes.
Apply service brakes
Air loss should not exceed
3 psi per minute on single vehicles.
4 psi per minute on combination.
Fig. 5
WALKAROUND SEQUENCE
Step 10 - On Trailer Transporting
Hazardous Material
1. Check marking and placards.
2. Check for proper shipping papers.
19
4.6
HOOKING UP/UNHOOKING
Special care should be taken when hooking
up or unhooking trailers to be sure the
equipment is in good condition and all
systems are functioning as required.
4.6.1
HOOKING UP
Follow this procedure when hooking up
the trailer to towing vehicle (tractor or lead
trailer):
1. Back the towing vehicle up in a straight
line to the trailer and align the fifth wheel
opening with the trailer king pin.
2. Stop before the fifth wheel makes
contact with the trailer and apply the
towing vehicle parking brake.
3. Inspect all the coupling components
before hooking up:
a. Inspect trailer coupling components.
Check that king pin is not broken,
bent or chipped. Check that the
oscillating plate is not bent or
cracked. Check that the pivot
bushings are in good condition and
that the mounting fasteners are
tightened to their specified torque.
If problems found, correct before
proceeding.
b. Inspect fifth wheel coupling
components. Check that the
fifth wheel assembly is securely
anchored to the B train or tractor
frame. Check that the structure of
the frame, pivot and fifth wheel is
not bent, broken or cracked. Check
that the jaws of the lock are open.
If problems found, correct before
proceeding.
c. Be sure that the fifth wheel plate is
Fig. 6
cleaned and greased.
4. Open the coupler lock.
5. Tilt the fifth wheel plate back.
6. Check that the trailer is at the required height to
slide onto the fifth wheel.
a. Use the crank on the landing gear to raise or
lower the trailer as required.
The trailer oscillating plate should contact the fifth
wheel just behind the pivot point as the towing
unit backs under the trailer.
20
King Pin
Fifth Wheel
COUPLING COMPONENTS
7. Block the trailer wheels.
8. Connect brake lines. Route the lines so they do
not get pinched when the trailer is attached to
the tow unit.
9. Check brake application by
applying and releasing brakes. If
brakes do not release, air lines may
be crossed. Do not continue unless
brakes are functioning properly.
10. Re-apply trailer brakes using trailer
hand valve.
11. Back slowly under trailer keeping
the king pin centered in the fifth
wheel jaws.
12. Back up until the fifth wheel coupler
locks on the trailer king pin.
13. Gently move the towing vehicle
back and forth while the trailer
brakes are engaged to check that
the jaws have locked around the
king pin.
14. Set parking brake, stop engine and
dismount.
15. Visually check that the coupler jaws
are securely locked around the king
pin and the coupler release lever is
in the locked position. Release and
hook up again if the jaws are not
securely locked around the king pin.
16. Check that the trailer oscillating
plate is resting on the fifth wheel.
Fig. 7
COUPLER LOCKS
17. Connect and secure the electrical
terminal. Check that all electrical
circuits are completed and that all lights are
working.
18. Route the electrical and air lines to prevent
snagging, dragging and pinching.
19. Raise the landing gear.
Use the crank to raise the legs if
equipped with the crank style.
Stow crank.
20. Remove blocks or chocks from the wheels.
21. Perform Pre-Trip Inspection before starting.
21
4.6.2
UNHOOKING
1. Position towing unit and trailer in a straight
line on a clear, level and firm surface.
2. With Clam system, close discharge gates so
the legs are directed straight down.
3. Apply the trailer brakes and the parking
brakes on the tractor before dismounting.
4. Place blocks or chocks in front of and behind
trailer wheels.
5. Place large blocks or planks under landing
gear if the ground is soft.
6. Lower landing gear:
Use crank to lower leg on crank style
landing gear. Lower leg until pads solidly
contact the ground but do not lift trailer off
fifth wheel. Stow crank.
Fig. 8
CLAM GATES
7. Unhook fifth wheel coupler.
8. Charge trailer air system and apply brakes using
trailer hand valve.
9. Release tow unit parking brake and pull slowly
forward until the trailer apron just slides down the
fifth wheel ramp. Stop.
10. Set the parking brake on the tow unit before
dismounting.
11. Check that the surface under the landing pads
can support the trailer. Support with blocks or
planks if required. This is particularly important if
the trailer will be loaded while unhooked.
Clam
12. Disconnect air line and electrical connector.
IMPORTANT
Only crank type landing gear can
support a loaded trailer.
13. Install glad hands on dead end connectors if so
equipped.
14. Drive tow vehicle away from trailer.
15. Inspect the equipment. Document problems
found so they can be corrected before the unit
will be used the next time. Record problems and
repairs for your files.
CUL
Fig. 9
22
UNHOOKED
4.7
DISCHARGE GATES
The clam shell discharge gate style is
designed so the gates are aligned
perpendicular with the trailer body.
Manual levers on each side of the gate
control the gate for opening or closing.
Gate opening width is set manually.
Fig. 10
CLAM DISCHARGE GATE
23
4.8
AIR SYSTEM
4.8.1
TANKS
The air system
is designed with a filter and an
oiler to remove contaminants from and add
Pressurized
airtofrom
tractor air
a light oil mist
the the
air supply.
compressor feeds into the tanks until it is
needed
by the brakes and tanks. In this way
A. Filter:
eachThe
system
will havefilter insures that only
self draining
sufficient
air
at
the to
appropriate
to
dry air is used
move the pressure
air cylinders
provide
the
required
response.
for opening and closing the discharge
gates. Any moisture in the air will wear
Pull the
the seals
cablesand
on packing
the valves
to drain
in the
cylinder
moisture
from
the
tanks
every
day or daily,
or freeze in cold weather. Check
moredrain
frequently
in high humidity or cold
if required.
temperature conditions.
B. Oiler:
IMPORTANT
The oiler introduces
a fine oil mist
into the air stream as it moves into
or through
thetocylinder.
The oil mist
Recent
revisions
DOT regulations
lubricates
allpressure
the internal
andinmoving
mandate
higher
levels
trailer
cylinder
components.
Without oil,gate
air supply
lines.
Do not compromise
the seals
and wiperswith
in steel
or braking
performance
low cylinders
pressure.
willyour
dry out
and wear
rapidly
until the
Check
tractor.
Set the
compressor
cylinder
fails.
cut-in
pressure
to 105 psi and cut-out to not
more than 120 psi.
Keep oil in the oiler at all times.
Establish the oil consumption rate for
your application and add oil before the
oiler is empty. Refer to Section 5.2.16
for filling and adjusting procedure.
Check the oil level on a daily basis.
NOTE: Composite cylinders do not
require filter and oiler
NOTE: The standard cylinder on
the CUL trailers is the composite
cylinder, hence oilers are not
required.
Fig. 11
24
TANKS (TYPICAL)
4.9
LOADING/UNLOADING
It is the responsibility of the operator to review
and be familiar with the trailer loading capacity
specifications and be sure that you comply with any
and all load limitations or restrictions applicable in the
jurisdictions where you will be travelling. Exceeding
the trailer weight specifications can result in damage
to the structure and voids the manufacturer's
warranty. Exceeding the road restrictions is illegal.
Loading/unloading procedures and instructions are
covered but not limited to those summarized below:
A. Loading
1. Clear the area of bystanders and remove
debris from loading area.
2. Position the trailer as required and set
park brake before dismounting.
3. Be sure discharge gate is closed and
trailer air system is charged.
4. Minimize the drop height when
loading.
a. Position the loading equipment
as close to the bottom of the
trailer as possible.
b. Do not load trailer unless hooked
to towing unit.
5. Do not drop large dense objects into
the trailer as they can damage the
structure.
6. Distribute the material evenly from
side-to-side and front-to-rear during
loading to equalize the structural and
axle loading during transport.
7. Secure the trailer cover as required.
Manual Roll Tarp
Fig. 12
LOADING
25
4.9 LOADING/UNLOADING (Cont’d)
B. Unloading
1. Clear the area of bystanders and remove
debris from unloading area.
2. Proceed to the unloading area.
4.10
TRANSPORTING
By following the previous instructions, your Midland
SandRunner trailer has been hooked-up and is ready
to go. Although all operating instructions are common
sense, it is wise to review them periodically to refresh
your memory. Good operational procedures result in
a safe workplace for the operator and others.
IMPORTANT
Use care when applying brakes, while backing
up a trailers equipped with an Air-Ride
suspension system. When applying the brakes
aggressively, the axle dynamics can result in the
air spring over-extension and can cause
component damage. No damage will occur with
slow speeds and gradual braking.
3. When unloading with a partner, always have
constant visual contact with your partner
before operating a discharge gate. It is
recommended that only the partner operate
the discharge gate(s). When unloading, the
partner can operate the discharge gate(s)
with the manual controls on the side of the
trailer frame.
4
Know the characteristics of the material
being handled. Never enter the trailer if toxic
material is being handled.
4.10.1
OPERATING INSTRUCTIONS
Since this equipment can be used in a variety
of conditions, it is difficult to give instructions
appropriate for all applications. However, these
general guidelines apply to all situations:
1. Be sure that the trailer is securely attached to
the towing vehicle or lead trailer and locked into
position.
2. Be sure that the air lines are securely connected
and that they have sufficient slack for turns.
3. Ensure that the brakes are properly adjusted and
in good working condition.
4. Ensure that the electrical harness is securely
attached and all lights and reflectors are clean
and operating.
5. Maintain the mud flaps in good condition to
minimize road splash in wet conditions.
6. Always maintain the trailer in good mechanical
condition.
#1812305
26
4.10
TRANSPORTING (cont'd)
4.10.2
BRAKING GUIDELINES
Safe, reliable and trouble-free operation of your
trailer requires that the brakes be maintained in
good operating condition at all times and the driver
follows good application techniques when driving.
The irresponsible use of brakes by the driver when
traveling can contribute to low brake life or result in
system malfunctions, short life and poor tire wear
patterns. The following list summarizes some basic
operational guidelines for the driver.
1. Check the function of the brake system before
starting a trip.
2. Maintain a safe vehicle speed at all times.
Slow down for rough road or slippery surface
conditions, winding roads or congested areas.
3. Always provide sufficient vehicle spacing on the
road to allow for a safe stopping distance.
4. Apply brakes gradually to produce an even
deceleration until the vehicle is stopped.
5. Watch traffic patterns ahead. Anticipate pattern
changes that could result in an emergency. Apply
the brakes gradually in sufficient time to produce
a controlled stop.
6. Shift to a lower gear to use engine compression
as the retarding force when going down steep
grades.
7. Do not apply brakes for a long period of time
such as when traveling on a long downgrade.
The brakes will overheat. Instead, apply both
the tractor and trailer brakes for short periods of
time giving the brakes a chance to cool between
applications.
8. Dry the brakes by applying them several times
after going through water.
9. Release the brakes just before going over railroad
tracks or other rough conditions. By allowing
the wheels to turn over rough road surfaces,
there will be no shock loads to the brake system
components or produce flat spots on the tires.
10. Wet, icy or snow-packed surfaces require special
care. Make cautious, intermittent applications by
fanning or pumping the brakes to reduce speed
without skidding or locking the wheels.
11. Use caution when applying the tractor driveline
brake should you lose the service brake system.
Rapid and hard application of the driveline brake
can result in axle or driveline component failures
with the resulting loss of all braking systems.
12. Use wheel chocks, apply trailer and tractor
parking brakes and place tractor in low gear
when parking the unit.
13. Maximum brake retarding occurs just before the
wheels lock up and the tires skid. Release the
brakes should you feel them lock-up and reapply
them.
14. When trailer brakes are applied with hot drums, it
may result in a cracked drum. Allow them to cool
before reapplying the brakes.
15. Fanning or repeated on-and-off applications will
use up the system air reserves. This procedure
is not recommended unless adverse road
conditions are encountered. The wasting of air
reserves in this way could result in insufficient
application pressure should an emergency arise.
16. Hard or panic stops can overheat the linings
and drums. Overheating will cause brake fade.
Severe overheating and fade can result in the
complete loss of braking capability. This will
substantially reduce the expected life of brakes.
27
4.10.3
TIRES
When operating the trailer, it is the responsibility
of the driver to check the tires frequently. Inflation
pressures, wear patterns and matching are critical
parameters that must be monitored. The following
factors affect tire care:
1. Inspection frequency: Tires should always
be checked before the start of a run and twice
during the day or every 4 operating hours,
whichever comes first. It is also a good practice
to check the tires at each rest period during
the day. When a driver hears unusual noise or
experiences unusual handling characteristics,
the first item to check is the tires. Problems
found early, during frequent tire checks, can save
more serious problems later on. A sampling of
typical abnormal wear patterns are shown in the
Maintenance section along with their causes.
Always correct the cause of the tire wear problem
before proceeding.
2. Inflation pressure: Tires should always be
operated at their specified pressures. At their
specified pressures, the tire is designed to run
with the full width of the tread flat on the contact
surface. Operating at other than specified
pressures will change the tread
contact patterns and can dramatically shorten tire
life. In addition, the tires will run hotter and can
lead to blow-outs.
Check tire pressure when the tire is cold. A hot
tire can read as much as 20 psi higher than a cold
tire. If tires are over-inflated, check for poor load
distribution, uneven surface contact, over-loading
or poor operating conditions.
3. Tire matching: Do not mix ply types on the
same axle. Their operating characteristics are
different and will lead to uneven tire loading, rapid
tire wear and adverse handling characteristics.
Matching also includes combining tires that have
the same amount of tread remaining. A tire with
more tread has a larger rolling radius and will
have to carry a higher load. The best performance
will be obtained when the rolling radius is within
1/8" for all tires on an axle.
28
5
SERVICE AND MAINTENANCE
This section provides information on daily and
periodic service and maintenance of the Trailer
unit. Follow these recommendations for safe and
dependable operation of the Trailer unit. Refer to the
safety section at the front of the operator's manual
for all applicable safe maintenance and operating
procedures.
Be sure that all operators are familiar with the
operation and maintenance procedures and related
safety information contained in the operator's manual.
5.1
SERVICE
5.1.1
FLUIDS AND LUBRICANTS
1. Grease:
Use an SAE multi-purpose lithium based grease
with extreme pressure (EP) characteristics.
2.
Wheel Hub Oil:
a. Use an SAE 80W90 for normal temperature
conditions (-10°F to 100°F ambients).
b. Use an SAE 85W140 for hot temperature
conditions (100°F and hotter ambients).
c. Use an SAE 30W motor oil for ambients below
-10°F.
Capacity: 1 pint (500 ml)
3.
General Purpose: I.S.O. Viscosity Grade 32 at 40ºC
ESSO
- NUTO H 32
SHELL
- TELLUS 32
PETROCAN/
GULF
- HARMONY AW 32
Extreme Low Temp.:
ESSO
- UNIVIS N 32 (-10ºC - 40ºC)
- UNIVIS N 22 (-20ºC - 0ºC)
- UNIVIS N 15 (-40ºC - 0ºC)
MAINTENANCE SAFETY
1. Read and understand all the information in
the Operator’s Manual regarding maintenance, adjusting and servicing the Trailer
unit.
2. Place all controls in neutral, stop the
engine, remove ignition key and set the
park brake before adjusting, servicing or
maintaining any part of the Trailer unit.
3. Follow good shop practices:
- Keep service area clean and dry.
- Be sure electrical outlets and tools
are properly grounded.
- Use adequate light for the job at
hand.
4. Cage spring brake chamber before
disassembling.
5. Block wheels before de-activating brakes.
6. Maintain fasteners in running gear
systems at their specified torque at all
times.
7. Establish and maintain a Trailer
Preventative Maintenance (TPM) program
on your equipment. Some jurisdictions
require this program and the maintenance
of records on every commercial vehicle
on the road for future reference.
NOTE
The general purpose I.S.O. 32 are equivalent to SAE
10, Mobile DTE Light as mentioned in Wilkerson
Catalog 173, page 19.
4.
Storing Lubricants
Your Trailer can operate at top efficiency only if
clean lubricants are used. Use clean containers
to handle all lubricants. Store them in an
area protected from dust, moisture and other
contaminants.
5.1.2
GREASING
Refer to Section 5.1.1 for recommended grease.
Use the Service Record checklist provided to keep a
record of all scheduled servicing.
1. It is recommended that a hand-held grease gun
be used for greasing. An air-powered greasing
system can damage the seals on bearings and
lead to early failure.
2. Wipe grease fitting with a clean cloth before
greasing, to avoid injecting dirt and grit.
3. Replace and repair broken fittings immediately.
4. If fittings will not take grease, remove and clean
thoroughly. Also clean lubricant passageway.
Replace fitting if necessary.
29
5.1.3
SERVICING INTERVALS
A standard servicing schedule
is provided as a guide for your
convenience. In unusual or extreme
operating conditions, increase the
frequency or perform additional service
items to customize this schedule to your
application.
Your Midland SandRunner is equipped
with Duralon Bushings at all major
pivot points. These high performance
bushings do not require lubrication
or any other maintenance. The Teflon
Fibers woven into the bushing liner
provide the lubrication.
8 Hours, Daily or 500 Miles
1. Drain moisture from air tanks (use
cables to open drain valves).
Fig. 13
30
DRAIN CABLES (TYPICAL)
8 Hours, Daily or 500 Miles (cont'd)
2. Check tire air pressure. Add as
required.
Weekly, 10 Days or 5000 Miles (cont'd)
Weekly, 10 Days or 5000 Miles (cont'd)
Fig. 14
TIRES (TYPICAL)
Weekly, 10 Days or 5000 Miles
1. Grease slack adjusters.
Refer to Haldex Service manual.
2. Refer to Haldex Brake Systems manual.
3. Grease fifth wheel.
a.
b.
Pivots (2 locations).
Surface
4. Check wheel hub oil levels.
Hub
Fig. 15
HUB OIL LEVEL
31
Hub
Weekly, 10 Days or 5000 Miles (cont'd)
6. Retorque the following
fasteners:
a. Oscillating plate bushing
anchor bolts to 250 ft.
lbs.
Fig. 16 BUSHING ANCHOR BOLTS
b. Brake/wheel end system
fasteners.
Refer to Section 5.2.8.
WARNING! Failure to
follow this instruction
could cause the wheel
to come off and cause
bodily injury. Failure to
back off the nut will
cause the bearing to run
hot and be damaged.”
Fig. 17
BRAKE/WHEEL END
c. Landing gear bolts torque
values (Crank type only).
1/2 in.
5/8 in.
80 ft. lbs.
160 ft. lbs.
Fig. 18
32
LANDING GEAR MOUNTING BOLTS
Weekly, 10 Days or 5000 Miles (cont'd)
Weekly, 10 Days or 5000 Miles (cont'd)
d. Retorque cast spoke wheel rim
nuts if so equipped.
d. Retorque cast spoke wheel rim
nuts if so equipped.
Table 1 Recommended Wheel Bolt
Torque (Spoke Wheels)
Ft-lbs Torque (Dry)
Size Bolt
Table 1 RecommendedBolt
Wheel
Torque (Spoke Wheels)
150 - 175
5/8" - 11
Bolt Size
3/4" - 10
Ft-lbs Torque
(Dry)
5/8" - 11
150 - 175
3/4" - 10
210 - 260
3 Spoke
5 Spoke
3 Spoke
5 Spoke
IMPORTANT
Do not over-torque fasteners.
Over-torquing can strip threads,
collapse spacers or lead to
210 - 260
other problems that cause loose
fasteners. Use an accurate
torque wrench when tightening
fasteners.
6 Spoke
Torquing Sequence
IMPORTANT
Do not over-torque fasteners.
Over-torquing can strip threads,
collapse spacers or lead to
other problems that cause loose
fasteners. Use an accurate
torque wrench when tightening
fasteners.
6 Spoke
Torquing Sequence
Wheel (Typical)
Fig. 19
CAST WHEEL RIM NUTS
Wheel (Typical)
Fig. 20
RIMS
33
Weekly, 10 Days or 5000 Miles (cont'd)
e. Retorque for stud
pilot inner and outer
wheel nuts if so
equipped.
Table 2 Recommended Wheel
Stud Torque (Disc Wheels)
Stud
Size
Wheel
Type
Ft-lbs
Torque
(Dry)
3/4" - 16
Disc
450 - 500
1-1/8" - 16
Disc
450 - 500
15/16 - 12
Disc
750 - 900
1-5/16 - 12
Disc
750 - 900
Inner Schematic (Typical)
390 - 440
Bud
Unimount
10
WHD-8 400 - 600
Fig. 21
f.
Outer
10 STUD WHEEL NUTS (Table 2)
Retorque hub piloted
wheel single nuts if so
equipped.
Table 3 Recommended Wheel
Stud Torque
Stud
Size
Ft-lbs
Torque
(Oiled)
M22 x 1.5
(33 mm or 1-1/2 Hex)
450 - 500
M20 x 1.5
(30 mm Hex)
280 - 330
Fastener Schematic
IMPORTANT
Do not over-torque
fasteners. Over-torquing
can strip threads, collapse
spacers or lead to other
problems that cause
loose fasteners. Use an
accurate torque wrench
when tightening fasteners.
Wheel
Fig. 22
34
SINGLE NUTS (Table 3)
Weekly, 10 Days or 5000 Miles (cont'd)
Weekly, 10 Days or 5000 Miles (cont'd)
Retorque
suspension
system fasteners
Weekly,g.
10 Days
or 5000
Miles (cont'd)
(Refer to charts for torque levels in
g. Maintenance
Retorque suspension
system fasteners
Section 5.2.1.
g. Retorque
system
fasteners
(Refer to suspension
charts for torque
levels
in
(Refer
to
charts
for
torque
levels
in
Maintenance Section 5.2.1.
Maintenance Section 5.2.1.
Air
Mechanical
Fig. 23
SUSPENSION SYSTEM U-BOLTS
10,000 Miles (15,000 km) or Monthly (cont'd)
1. Retorque fasteners.
Torque mechanical system suspension
(refer to Section 5.2.12.2).
Fig. 24
MECHANICAL SUSPENSION SYSTEM
35
25,000 Miles (40,000 km), Quarterly or Every 3 Months
1. Check condition of wheel ends.
Release brakes, jack up the axle and
spin the wheel. Check:
a.
b.
c.
d.
Wheel bearings.
Wobble.
Rims and tires.
Brake drag.
Fig. 25
WHEEL END
2. Inspect frame and structure
for bends, distortions or
cracks.
a. Oscillating plate and kingpin.
b. Fifth wheel and mounts.
c. Longitudinal and transverse
frames.
d. Compartment structure.
e. Discharge gate structure.
f. Suspension system
anchorage.
g. Axles.
h. Optional Accessories:
Tarp
Fig. 26
SandRunner (TYPICAL)
3. Inspect electrical system
components for:
a.
b.
c.
d.
e.
f.
Binding.
Rubbing/abrasion.
Looseness/dangling.
Cracks/tears in harness.
Burned out lights.
Check that front electrical
connector plug anchor female
trailer receptical.
Fig. 27
36
ELECTRICAL (TYPICAL)
25,000 Miles (40,000 km), Quarterly or
Every 3 Months (cont'd)
4. Inspect air system and
components for:
a. Perform leak-down
test.
b. Rubbing/abrading air
lines.
c. Cracked hoses.
Fig. 28
AIR SYSTEM (TYPICAL)
5. Clean gladhand
screens.
Fig. 29 SCREENS
6. Check brake lining
thickness.
Replace as required.
Fig. 30
BRAKE LINING
7. Check landing gear.
Fig. 31
37
Weekly, 10 Days or 5000 Miles (cont'd)
100,000 Miles (150,000 km) or Annually
1. Change oil in hubs.
Fig. 32
5.1.4
5.1.4
HUB OIL (TYPICAL)
SERVICE RECORD SUMMARY (LUBRICATION)
SERVICE RECORD SUMMARY (LUBRICATION)
LOCATION
DESCRIPTION
FREQUENCY
LUBRICANT
LUBRICANT
Chassis
grease.*
LOCATION
Fifth wheel.
DESCRIPTION
Coat bearing surface.
FREQUENCY
Daily
or as needed.
Coat pivot pins
Fifth wheel.
and lock
Coat bearing surface.
Daily or as needed.
Gearbox and screws.
Periodic basis (weekly).
Coat pivot pins
Landing gear
and lock
Hub
Chassis grease.*
Wheels
Landing
gear
Check oil level.
Gearbox
and screws.
Weekly, 10 Days or 5000 m
Periodic basis (weekly).
(8000 km)
Wheels
Check
oil level.
Bearings.
Weekly,
10 (40,000
Days or
5000 mSAE 80W90 gear oil.
25,000
miles
km).
Change oil.
Brakes
Bearings.
Camshaft bearing
Change oil.
Slack adjuster
Brake shoe anchor
pin bushing
Slack adjuster
SAE 80W90 gear oil.
25,000 miles (40,000 km).
SAE 80W90 gear oil.
Lubricate
5,000 miles (8,000 km)
Chassis grease.*
100,000 miles (150,000 km).
SAE 80W90 gear oil.
or monthly.
Lubricate
5,000 miles (8,000 km)
5,000
miles (8,000 km)
or
monthly.
Lubricate
30,000 miles (50,000 km) or
yearly.
Brakes
Camshaft bearing
(8000 km)
100,000 miles (150,000 km).
Lubricate
Lubricate
Also at brake reline.
or monthly.
Chassis grease.*
Chassis grease.*
5,000 miles (8,000 km)
or appropriate.
monthly.
As
30,000 miles (50,000 km) or
Lubricate
Brake shoe anchor
yearly.throughout.
pin bushing
* Use a good quality lithium based extreme pressure grease
MIL-G-25013C in below -40°F.
Also at brake reline.
NOTE: Do not use excessive lubricant.
As appropriate.
38
* Use a good quality lithium based extreme pressure grease throughout.
MIL-G-25013C in below -40°F.
5.2
PERIODIC MAINTENANCE AND ADJUSTMENTS
MAINTENANCE SAFETY
1. Read and understand all the information in
the Operator’s Manual regarding maintenance, adjusting and servicing the Trailer
unit.
2. Follow good shop practices:
- Keep service area clean and dry.
- Be sure electrical outlets and tools are
properly grounded.
- Use adequate light for the job at hand.
3. Cage spring brake chamber before
disassembling.
4. Block wheels before de-activating brakes.
5. Disconnect air lines and exhaust air system
completely before working on discharge
gates.
6. Establish and maintain a Trailer Preventative
Maintenance (TPM) program on your equipment. Some jurisdictions require this program
and the maintenance of records on every
commercial vehicle on the road for future
reference.
5.2.1
Your trailer can only operate at top efficiency
when it is maintained in good operating condition.
The maintenance procedures are summarized
from the component manufacturers instructions
included with this manual. Standard industry and
component procedures are required to keep your
trailer in top condition. All maintenance intervals
are established for normal operating conditions. In
light or intermittent conditions, the servicing and
maintenance intervals can be extended. In heavy,
extended or severe off-highway application, reduce
the intervals for servicing and maintenance to keep
the equipment in good condition. When a problem is
found, correct the condition before continuing.
A good maintenance program will find conditions
early when they are easily and quickly corrected
before they become major problems. Operating your
trailer in a defective condition, can lead to serious
mechanical problems or can create safety hazards for
the driver, bystanders or other operators.
TORQUE SPECIFICATION SUMMARY
Table 4 Recommended Torque Specifications
1. Oscillating Plate
2. Air Ride Suspension
Oscillating Plate
Oscillating 5th Wheel
Bushing Bolts
3/4"
lbs.
250 ft.
39
Table 4 Recommended Torque Specifications (cont'd)
3. Wheel End Components
Torque Range
(lb-ft)
N.m
Description
1.
2.
3.
4.
5.
6.
7.
8.
9.
10-15
15-20
Tighten to 100,
loosen, tighten
to 50, loosen
1/4 turn
Jam nut - manual bearing adjustment
250-300
Brake mounting bolt
130-165
Two-piece dust shield bolts (shown)
• Forged spider
15-20
Bolt-on bushing bolts
25-35
Cam bushing bolts
25-35
80-125
Air chamber nuts
Hub-cap bolts
Hub fill plug
Adjustment nut - manual bearing
adjustment (double nut)
Fastener
Size
13-20
20-27
136
68
5/16"
3/8"
Size depends on axle model
and adjustment method.
340-408
177-224
5/8"
20-27
34-48
34-48
109-170
3/8"
3/8"
3/8"
5/8"
4. Wheel Nut
Stud Size
Wheel Type
Ft-lbs Torque
(Dry)
3/4" - 16
Disc
450 - 500
1-1/8" - 16
Disc
450 - 500
Bud Unimount 10
WHD-8
390 - 440
400 - 600
40
Bolt Size
Ft-lbs Torque (Dry)
5/8" - 11
150 - 175
3/4" - 10
210 - 260
5.2.2
KINGPIN AND OSCILLATING FIFTH WHEEL PLATE
The kingpin at the front of the trailer is the structural
component used to transmit accelerating and
decelerating loads into the trailer frame. It must be in
good condition to perform as required.
Visually inspect the kingpin as part of
the pre-trip inspection, at 5,000 miles
(8,000 km) or weekly and annually
as part of your normal preventative
maintenance program. Be sure the
kingpin does not have excessive wear,
looseness, chipped out areas, cracks
or bent mounting frame. If any kingpin
shows such defects, it should be
replaced immediately.
Fig. 33
KINGPIN
Visually inspect the frame and structure of the
oscillating plate for bends, cracks or distortions as
part of the pre-trip inspection procedure. Thoroughly
inspect the structural integrity of the assembly every
25,000 miles (40,000 km) or every three months as
part of your preventative maintenance program.
Replace the entire assembly if any structural defects
are found.
IMPORTANT
If a lube plate is used in your
operation, make sure to check
the kingpin length. The kingpin
must be sized to compensate for
the thickness of the lube plate.
Otherwise, the kingpin will be
too short. If the kingpin length is
improper, the kingpin should be
replaced.
Retorque the oscillating plate anchor
bolts to 275-325 ft/lbs after first 500
miles and every 10,000 miles (15,000
km) thereafter. Loose anchor bolts will
reduce or eliminate the effectiveness
of the rubber bushings and can lead to
premature failure. Always attach the
torque wrench to the Stover lock nut
when tightening. Inaccurate readings
are obtained when tightening the bolt
head.
Fig. 34
ANCHOR BOLTS
41
5.2.3
FIFTH WHEEL
A fifth wheel system is used
on the rear of the front B train
unit and on the towing tractor
to secure the kingpin and carry
the weight of the attached
trailer. It must be maintained in
good condition to perform as
intended.
Visually inspect the fifth wheel as
part of the pre-trip inspection to
check for cracks, bends, chips
or distortions of the frame and
upper plate.
NOTE
Use a high-pressure washer
or steam cleaner to remove
all the dirt and grease from
the fifth wheel assembly prior
to each weekly inspection.
Apply a fresh coat of grease
to the fifth wheel assembly
prior to hooking-up the trailer.
Fig. 35 FIFTH WHEEL
Clean the assembly every 5,000 miles (8,000 km)
or weekly and annually to perform a thorough
inspection. Check the frame and upper plate for
cracks, bends, chips or distortions.
When the components are clean, check that the
lock closes completely around the kingpin.
To adjust the lock:
1. Obtain a Holland kingpin lock tester and
place in the throat of the lock. Close the
lock.
2. The jaws should be snug around the tester
but not binding.
3. Use the adjusting nut on the front edge of
the fifth wheel to set the clearance of the
jaws.
4. Use a light oil to lubricate all moving parts
prior to returning to service.
42
Fig. 36
KINGPIN LOCK
5.2.4
AXLE ALIGNMENT
A standard axle is used as the main transverse
structural member to transmit loads between the
trailer frame and the surface contacting components.
All running gear components are attached to or part
of the axle assembly.
Although there is very little that can go wrong with
the axle itself, loose, bent or damaged attaching
components can cause the axle to go out of
alignment. This misalignment will be found during the
regularly scheduled 25,000 mile inspection. However,
axle misalignment shows itself most commonly
by accelerated tire wear and dogtracking by the
trailer. Visually check the tire wear when checking air
pressure. The driver should identify these handling
characteristics to service personnel or correction.
To check axle alignment, follow this procedure:
1. Select a working area that is level, with a
compacted surface and is large enough to
provide access from all sides.
2. Move the trailer forward and backward
several times to remove any binding from the
components.
3. Stop the trailer when moving in the froward
direction without using trailer brakes. This will
give the components a forward bias with no
binding.
4. Unhook the trailer and support on the landing
gear at the normal highway height and parallel to
the ground.
5. Install a commercially available axle extender
on each axle or remove the wheels to prevent
any components from interfering with the
measurements.
43
5.2.4
AXLE ALIGNMENT (cont’d)
6. Attach an S hook to a steel tape and
measure the distance between the
kingpin and the end of each axle.
Dimensions A and B should be equal
within ± 1/8 inch (0.125 in) (3.1 mm).
7. Adjust the suspension mounting
system as required to set dimension
A and B within 1/8 inch (0.125 in) (3.1
mm). Refer to suspension system
instruction brochure for detailed
adjustment procedure.
Fig. 37
AXLE DIMENSIONS
8. Use a trammel bar to measure the road and
curbside dimensions between the first and
second axles. Dimensions C and D should be
within 1/16 inch (0.0625 in) (1.6 mm).
IMPORTANT
It may be necessary to build a
large trammel bar to measure and
clear the discharge gates.
Fig. 38
TRAMMEL BAR
9. Set the suspension system as required to set this
dimension to its recommended tolerance.
10. Repeat measuring and adjustment procedure on
the third axle if so equipped.
11. Tighten all fasteners to their specified torque. Do
not allow any suspension system or running gear
fasteners to loosen.
IMPORTANT
Always use a torque wrench when
tightening fasteners. The correct
torque on a fastener provides
the proper clamping force on the
adjacent components and they will
perform as expected.
12. The front axle must be aligned to the kingpin with
second and third axles adjusted to the front axle.
13. Always check axle alignment after repairing the
suspension system.
Fig. 39
44
ALIGNED
5.2.5
WHEEL HUBS/BEARINGS
All axles use an oil bath design for lubricating wheel
bearings. It is a virtual zero maintenance system
providing that the oil remains in the hub.
Visually check the hub every day for leaks when
checking tire pressure during pre-trip, daily, refueling,
or rest stop inspections. If oil leaks are detected
Weekly, 10 Days or 5000 Miles (cont'd)
on any hub, repair the leak and refill the hub before
proceeding.
A. Oil Leaks:
Visually inspect the hub for leaks
every time the tire pressures are
checked. Leaks will normally be
visible as dust collects on the
escaping oil. Stop and correct the
leak immediately to prevent running
the hub low on oil. Running low or
without oil will quickly overheat the
hub and cause the bearings to seize.
Change the oil in the hub when
installing new seals to correct a leak.
B. Oil Level:
1. Check the oil level in each wheel
hub every 5,000 miles (8,000
km) or weekly and whenever an
oil leak is found. Clean the end
plate of the hub to remove the
dust, dirt or mud build-up.
The oil should be visible to the
top of the outer concentric
circle of the end cap. Add oil as
required through the fill plug in
the hub. Always use clean oil
and prevent contaminants from
entering the hub when adding or
changing oil.
2. Change the oil every 100,000
Fig. 40
miles (160,000 km), annually
or whenever the axle nuts are
retorqued or the brakes are
relined. The hub cavities must
be opened when retorquing axle
nuts or relining the brakes and
changing oil should be done as part of the
procedure.
OIL LEVEL
Hub
45
5.2.5
WHEEL HUBS/BEARINGS (cont'd)
C. Wheel Bearings:
Wheel bearings carry and transmit the load
between the wheels and the axles. In addition
to proper lubrication, the bearings must have the
recommended pre-load to perform as expected.
Bearing pre-load is set and controlled by the
torque of the wheel nuts on the end of each
spindle. Each hub must seat securely on its
bearings to prevent wobble or slop in the system.
Turning the wheel or wobbling it indicates the
condition and tightness of the hub/bearing
assembly.
1. Turning/Wobble:
a. Park the trailer on a level, hard surface
and release the brakes.
b. Place chocks in front of and
behind each wheel.
c. Jack each axle up until the tire
clears the ground.
d. Support the axle on a safety
stand to prevent slipping or
tipping.
e. Turning the wheel slowly to
check the condition of the
bearings and to determine if
the brakes are dragging.
Fig. 41
f.
Dragging Brakes: Can be felt as a
steady drag on the turning of the wheel
or at the same position or arc of the
rotation. Adjust the brakes to eliminate
the drag before resuming work.
g. Bearing Condition: Can be felt as the
wheel turns. Bearings in good condition
turn easily and smoothly. Bearings
in poor or bad condition can be felt
through the wheels as scraping, grinding,
dragging or bumps. Replace bearings
before resuming work.
46
WHEELS
h. Wobble: Grasp each side of the wheel or
tire and wiggle the wheel and assembly.
If the wheel or hub wobble on the spindle,
the bearings have lost their pre-load and
the wheel bearing adjusting nut requires
tightening.
NOTE
If the bearings are not in good
condition, replace them before
setting the pre-load.
C. Wheel Bearings (cont'd):
2. Bearing Pre-Load:
a. Place a pan under
the hub drain plug.
b. Remove the drain
plug from the hub
and drain the oil.
c. Remove the hub
end plate and lay
to the side.
d. Remove the set
screw from the
jam nut.
e. Remove the jam
nut and perforated
lock washer from
the spindle.
f. Use a torque
wrench to tighten
the adjusting
nut 100 ft-lbs.
(136 N.m) while
rotating the wheel
assembly in both
directions.
g. Back the adjusting
nut off to zero
torque.
h. Retorque the
adjusting nut
again to 50 ft-lbs
(68 N.m) of torque
while rotating the
wheel assembly in
both directions.
i. Loosen the nut 1/4
turn.
j.
k.
Install the
perforated lock
washer. Be sure
the adjusting nut
pin aligns with
the hole in the
lock washer. Turn
washer over and/
or adjusting parts
as required.
Install jam nut and
tighten to 250-300
ft-lbs. (340-408
N.m).
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
DESCRIPTION
Capscrew
Lockwasher
Hub cap
Gasket
Wheel bearing jam nut
Lockwasher
Wheel bearing adjusting nut
Cone outer wheel bearing
Cup - bearing outer
Brake drum
Cup - bearing inner
Cone - bearing inner
Seal wheel-bearing
Bushing anchor pin
Pin anchor
Beam axle
Camshaft (left)
Camshaft (right)
Washer
Seal
Bushing
ITEM
DESCRIPTION
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
Snap ring
Capscrew
Air chamber
Lockwasher
Locknut
Camshaft busing assembly
Capscrew
Washer slack adjuster
Locknut - slack adjuster
Automatic slack adjuster
Washer slack adjuster
Snap ring slack adjuster
Spring - brake shoe return
Brake show and lining assy.
Spring - brake shoe retaining
Retainer - brake shoe roller
Roller - brake shoe
Pin - shoe return spring
Dust shield
Hub
Fig. 42 SPINDLE COMPONENTS
47
l.
Check bearing end play by:
i. Attaching a magnetic base dial
gauge indicator to the end of the
spindle.
ii.
Push the wheel in while rotating the
wheel slightly until the dial gauge
reading doesn't change.
iii. Zero dial gauge.
iv. Pull wheel assembly out while
rotating wheel slightly until dial
reading doesn't change.
v.
Dial indicator will read bearing end
play.
In
vi. If end play does not register
between 0.001-0.010 inches
(0.025-0.25 mm), replace bearings
or hub components until it does.
m. Install a new gasket on hub face cap.
n. Install hub face cap and tighten
mounting cap screws to their specified
torque.
o. Add the specified amount of oil to the
hub and secure fill plug. Check for
leaks. Correct leaks before resuming
operation.
p. Remove safety stand from under axle
and lower wheel to the ground.
q. Repeat checks on all other axles.
48
Out
Fig. 43
DIAL INDICATOR
5.2.6
WHEELS
A variety of steel or aluminum wheels can be used
on the trailer depending on customer preference
or application requirements. Wheels must be
maintained in good condition and all fasteners
tightened to their specified torque level to obtain the
expected life and performance.
Loose fasteners are the most common cause
of wheel problems on a trailer. Always retorque
the wheel fasteners per the break-in schedule of
100, 500, 1500 and 5,000 miles (160, 800, 2500
and 8000 km) when the unit is new and after a
wheel has been removed. Always use an accurate
or calibrated torque wrench when tightening
fasteners. A loose fastener is defined as one that
is not tightened to its specified torque. A loose
fastener does not provide the required clamping,
anchoring or holding forces to stabilize the adjacent
components. Insufficient clamping forces can lead
to flexing, bending, cracking, hole elongation or other
component deterioration that cause failures and/
or accidents. Always keep fasteners tightened to
their specified torque. Over-torquing can overload
certain components, causing compression cracks
and strip nuts or studs. Over-torquing fasteners can
be as detrimental as under-torquing. Always tighten
fasteners to their specified torque.
Use an accurate torque wrench to retorque wheel
fasteners every 10,000 miles (15,000 km) or monthly
whichever comes first. Always retorque wheels per
the break-in schedule whenever a wheel is removed
and remounted.
Always follow the recommended mounting procedure
when installing wheels to the trailer.
6 Stud
STUD PILOTED
1. Disc Wheels (Stud Pilot Style):
a. Mount single or inner dual wheel on hub. Be
careful not to damage the threads on any of
the studs.
b. Snug the nuts up in the alternating sequence
shown to center it on the hub and insure an
even contact between the wheel and hub.
c. Tighten nuts to their specified torque using the
same alternating sequence.
IMPORTANT
Left-hand threads are used on
the left side of the vehicle. Righthand threads on right.
d. Mount outer dual. Do not damage the
threads when sliding the wheel over the
studs.
e. Snug up the nuts in the alternating sequence
shown to center it on the hub and to provide
even contact.
f. Tighten the outer wheel nuts to their specified
torque.
IMPORTANT
When retorquing inner nuts of
double nut design, always back
off outer nut several turns, then
retorque them.
Table 5 Recommended Wheel Stud Torque
(Disc Wheels)
Stud Size
Wheel Type
Ft-lbs
Torque (Dry)
3/4"-16
Disc
450 - 500
1-1/8"-16
Disc
450 - 500
15/16-12
Disc
750 - 900
1-5/16-12
Disc
750 - 900
Bud Unimount 10
390 - 440
WHD-8
400 - 600
10 Stud
Fig. 44 NUT TORQUE SEQUENCE
49
2. Hub Piloted Wheels:
a. Mount inner wheel on the hub.
b. Slide on the hub guide until the wheel is snug
against the hub. Be careful not to damage
the threads on any of the studs.
c. Mount outer dual wheel on the hub and snug
up against the inner wheel.
NOTE
Add a drop or 2 of oil on the end
of the bolt, threads and the nuts
and flanges.
8 Stud
d. Install nuts and tighten in alternate sequence
shown.
Table 6 Recommended Wheel Bolt Torque
Stud
Size
Ft-lbs
Torque
(Oiled)
M22 x 1.5
(33 mm or 1-1/2 Hex)
450 - 500
M20 x 1.5
(30 mm Hex)
280 - 330
10 Stud
Fig. 45
HUB PILOTED
IMPORTANT
Do not over-torque fasteners.
Over-torquing can strip threads,
collapse spacers or lead to
other problems that cause loose
fasteners. Use an accurate
torque wrench when tightening
fasteners.
3. Rim/Wheel (Cast Spoke):
a. Inspect and clean all the parts. Replace any damaged components.
b. Place rims and spacer band on
wheel. Be sure to space valve stem
between spokes.
c. Secure clamps evenly in position.
d. Snug up the nuts in the alternating
sequence shown to allow the inside
rim to seat itself on the mounting
bevel and avoid wheel wobble.
e. Tighten the nuts evenly in small
increments in the shown alternating
sequence until all nuts are tightened
to their specified torque.
3 Spoke
5 Spoke
Table 7 Recommended Wheel Bolt
Torque (Spoke Wheels)
50
Bolt Size
Ft-lbs Torque (Dry)
5/8" - 11
150 - 175
3/4" - 10
210 - 260
6 Spoke
Fig. 46
RIM/WHEEL TORQUE SEQUENCE
5.2.7
TIRES
Tires are one of the most important components on
a trailer and must be maintained in top condition
to obtain their desired load carrying capacity and
durability. Tire wear rate can be used as an indicator
of the condition of the axle alignment or suspension
system. Poorly maintained tires will wear rapidly
or deteriorate and fail quickly and suddenly. A
poorly maintained tire can and will affect adjacent
components leading to their potential failure as well.
Proper tire maintenance includes but is not limited to:
1. Inflation Pressure:
Operating at an incorrect inflation pressure is the
most common maintenance problem with tires.
Tires should be checked frequently to be sure
they are at their specified pressure.
It is recommended that tire pressure be checked
at the start of each working day and at least
one other time during the day. Always use an
accurate hand gauge when checking the pressure
and check each tire. Carry it with your unit so
it is always available when needed. The most
accurate pressure is obtained when the tire
is cold. Every tire has its specified operating
pressure molded into the sidewall. Adjust the
pressure as required to obtain the specified
inflation pressure when the tire is cold.
Tire pressure will normally increase 10 to 15
psi during operation as the tire heats up. If
the pressure exceeds this normal increase,
it indicates the tire may be overloaded,
underinflated, driven too fast, improperly sized
or a combination of these factors. Identify
the cause of the problem and correct it before
resuming work.
a. Underinflation:
Operating at lower than the specified
pressure is a tire's worst enemy. Use an
accurate tire pressure gauge to check the
pressure at the start of each working day,
every few hours during the day and/or
whenever the handling characteristics change
suddenly. Underinflation will increase tread
wear and cause a deterioration of the tire
body leading to a separation of the tread
from the body. An underinflated tire is soft
and deflects more than it should causing
fatigue cracks or breaks in the body cord
construction leading to sudden air loss.
Operation with a low or flat tire on a dual will
generate a lot of heat in the underinflated
tire from internal friction that it can and will
disintegrate or catch on fire. It also causes
overloading of the adjacent tire on the axle or
axles and could lead to their failure also.
b. Overinflation:
Inflating a tire over its specified pressure can
lead to serious problems also. Overinflation
creates a more rigid tire that does not
absorb road shocks as well as it should.
Shock loading from impacting bumps or pot
holes can break the fabric of the tire and/or
transmit the higher loads into the rim, wheel
and adjacent components causing them to
fail as well. Overinflated tires cut, snag or
puncture more easily than properly inflated
tires. Also overinflating tire will not increase
its load carrying capacity.
51
2. Tire Matching and Spacing on Duals
Tires on a dual assembly must be matched for size
(diameter or rolling radius) and type of construction to
obtain the desired and expected performance and life.
a. Matching of Size:
Tire sizes can vary between manufacturers and
as they wear. Special care must be taken to
be sure the tire size (rolling radius, diameter or
circumference) is within the following dimensions:
Rolling radius: 1/8 inch (3 mm)
Diameter:
1/4 inch (6 mm)
Circumference: 3/4 inch (19 mm)
Measure the tire when it is mounted, inflated to its
specified pressure and not loaded. The easiest
method is to use a steel tape to measure the
circumference of the tire.
Unequal sized tires will require the larger tire to
carry more of the load and potentially overload
it. Overloading accelerates the wear and can
lead to tire failure. When the one tire fails, the
remaining tire or tires will then also be overloaded.
The smaller tire will not contact the road surface
properly and will wear in an irregular manner giving
poor durability.
b. Tire Construction:
Customers can use radial or bias ply tires on their
trailer. However, it is recommended that different
types of tires not be mixed on an axle. Each
type of tire has different deflection, cornering
and spring characteristics. These differing
characteristics cause the tires to always fight
each other during operation and will give erratic
handling and poor wear characteristics when
mounted on the same axle. Different types can be
mounted on different axles but not on the same
axle.
c. Tire Spacing:
A wide variety of rims can be used on the trailer
and each will provide a different offset. Select
the rims to provide sufficient space and clearance
between the sidewalls of the tires. Normally
there should be at least 2 inches (50 mm) and 3
inches (75 mm) between the sidewall of a bias ply
and radial dual tire assembly respectively. This
spacing will provide sufficient clearance for each
type of tire to deflect as they rotate and when
they impact a pothole or bump in the road. If they
touch during operation, they will wear or abrade
at the contact point. In addition, tires that are too
close do not shed dirt, trash or stones that can
get between them during operation as well as
properly spaced tires.
52
Fig. 47
TIRE DIMENSIONS
5.2.8
BRAKES
All components in the brake
system must be maintained in
good condition for the system
to perform at top efficiency. It
is recommended that brakes
and associated components
be checked, serviced and
maintained per the Preventative
Maintenance Schedule (PMP)
for the trailer. In this section,
the basic brake disassembly
and assembly procedure will
be covered. Refer to the axle
manufacturers service manual
for a more detailed repair and
rebuilding procedure.
Check brakes frequently to keep
them in top condition. Poorly
maintained brakes will not stop
the trailer as effectively as wellmaintained brakes and in the
extreme could fail completely
leaving no brakes or no ability to
stop the unit.
Fig. 48
BRAKE SYSTEM
It is recommended that the driver checks the brakes
at least once during each working day when checking
tire pressure and performing a quick visual of the
unit. Place your hand on each brake drum to check
the temperature of the drum. All drums should be
approximately the same temperature if the system
is functioning properly. If any drum is significantly
warmer or colder than the rest, it indicates a problem.
Determine the cause of the problem and correct it
before resuming work. By discovering and correcting
it while it is a minor issue; major repair, expense and
down time can be prevented.
At 25,000 miles (40,000 km) or every 3 months when
the axle is raised off the ground for the complete
wheel end inspection, check the brakes at the same
time. When the wheels are turned by hand, the
wheel end should decrease speed slowly. If it does
not, the brakes could be dragging or there could be
a problem with the bearings. Dragging brakes will
also be detected by hot drums during the daily drum
temperature checks. Adjust the brakes to correct the
problem.
53
Remove the brake dust covers
(if so equipped) to access the
shoes. Check the thickness of
the linings. Reline or replace
shoes when the lining thickness
is less than 1/8 inch (3 mm).
Uneven wear among the brake
shoes on a trailer indicate that the
braking system has not been set
or maintained properly causing
uneven application and wear.
If uneven lining wear appears,
reset the system to provide even
application of all the shoes. Do
not operate when the linings
are less than 1/8 inch (3 mm) to
prevent the lining anchor rivet or
bolts from contacting the drum.
Head contact with the drum will
cut grooves in the surface and
require extra machining to remove
them when rebuilding the brakes.
Fig. 49 EXPLODED VIEW
Several types of friction material are available for
use on the brake shoes. Each has its own friction
coefficient and braking characteristics. Select the
one that best fits your application but do not mix
materials on the same trailer. Differing materials
require different application forces to obtain the same
braking force and a braking system can only apply
one force when it is properly set.
Recent changes in
environmental laws
have banned the use
of asbestos including
brake linings. Always use
the appropriate safety
gear when removing
brake shoes containing
asbestos from your trailer.
Replace the shoes that are
equipped with approved
material.
Fig. 50 AXLE
54
A. Removing Brakes:
1. Position the trailer on a level hard surface.
2. Exhaust all the air from the air system.
3. Jack the axle up and place on safety stands.
4. Remove the wheel assembly from the axle.
5. Release the slack adjuster (Refer to Section
5.2.6).
6. Disable or cage spring brakes if so equipped.
7. Drain oil from hub and remove spindle end
components.
8. Remove the hub and drum assembly.
Support with a hoist as the assembly slides
off the spindle. Use a puller if required.
9. Remove roller retaining clip from the bottom
and top brake shoe cam rollers.
10. Disconnect and remove bottom shoe return
spring.
11. Rotate bottom shoe to remove retaining
springs.
12. Lift top shoe to remove.
13. Disconnect push rod from slack adjuster.
14. Back off and remove slack adjuster.
15. Remove cam shaft.
Description
1.
2.
3.
4.
5.
6.
7.
8.
9.
Fig. 51
B. Installing Brakes:
1. Inspect all the components. Replace any
that are cracked, bent or worn.
2. Lubricate the camshaft spline, slack adjuster
gear and slack adjuster pins with anti-seize
compound.
3. Install cam shaft and slack adjuster. Secure
with snap rings.
4. Adjust slack adjuster to its required angle
and attach to the push rod. Release slack
adjuster pawl if so equipped.
5. Use a good quality brake grease to lubricate
the anchor pins and rollers where they
contact the brake shoes.
6. Place the upper shoe in position.
7. Place the lower shoe in position and attach 2
new retaining springs.
8. Rotate lower shoe forward and attach new
brake shoe return spring.
9. Install both cam rollers and secure with
retainers.
10. Install and secure the remaining wheel and
components.
11. Repeat with other wheel ends as required.
12. Tighten all fasteners to their specified torque.
Torque Range
(lb-ft)
N.m
10-15
15-20
Tighten to 100,
loosen, tighten
to 50, loosen
1/4 turn
Jam nut - manual bearing adjustment
250-300
Brake mounting bolt
130-165
Two-piece dust shield bolts (shown)
• Forged spider
15-20
Bolt-on bushing bolts
25-35
Cam bushing bolts
25-35
80-125
Air chamber nuts
Hub-cap bolts
Hub fill plug
Adjustment nut - manual bearing adjustment (double nut)
Fastener
Size
13-20
20-27
136
68
5/16"
3/8"
Size depends on axle model
and ajustment method.
340-408
177-224
5/8"
20-27
34-48
34-48
109-170
3/8"
3/8"
3/8"
5/8"
BRAKE/WHEEL END COMPONENTS
55
5.2.9
SLACK ADJUSTERS
5.2.9.1
HALDEX AUTOMATIC SLACK ADJUSTER
The Haldex S-ABA automatic brake adjuster
is a clearance sensing brake adjuster that
maintains a nominal distance or clearance
between lining and drum.
When the Adjuster is Installed:
With the brake in the released position, the
control arm is fixed to the anchor bracket.
The adjustment hex is rotated until the shoes
contact the brake drum and then backed
off 1/2 turn. When the brake is applied on
the first application, the endless rack rotates
to the correct position and sets itself.
When the Brake Applies:
When the brake is applied, the adjustment
regulator rotates through the normal
clearance angle and the shoes contact
the drum. The torque increases and the
wormshaft is moved axially, causing the coil
spring to be compressed and the clutch
wheel to disengage. The adjustment
components are free to rotate as the brake
continues to apply.
When the Brake Releases:
When the brake is released, the torque
decreases returning the wormshaft to the
clutch wheel and re-engaging the teeth.
The adjustment regulator rotates through
the normal clearance angle and the brake is
released. If lining wear has taken place the
adjustment regulator advances the clutch
wheel reducing the excess clearance during
the release stroke.
56
Fig. 52
HALDEX SLACK ADJUSTER (TYPICAL)
5.2.9
SLACK ADJUSTERS (cont'd)
5.2.9.2
AUTOMATIC SLACK ADJUSTER MAINTENANCE
In an S-cam type foundation brake, the final link
between the pneumatic system and the foundation
brake is the slack adjuster. The arm of the slack
adjuster is fastened to the push rod of the chamber
with a clevis and the spline end is installed on the
brake camshaft.
Primarily, the slack adjuster is a lever that converts
the linear force of the air chamber push rod into a
torque which turns the brake camshaft and applies
the brakes.
IMPORTANT
Automatic slack adjusters are
for brake adjustment and will not
compensate for faulty foundation
brakes.
Routine Visual/Operational Checks
- Haldex strongly recommends that routine visual/
operational checks, including brackets and
control arms, be performed at each Preventative
Maintenance Service Interval.
- Adjusters or anchor brackets that have visual
damage, or which fail the operational checks, MUST
be replaced immediately.
- Automatic adjusters should not be operated as
manual adjusters except as may be necessary to get
the vehicle off the road for service.
Service and Lubrication Intervals for
Standard Haldex AA1 and S-ABA Brake Adjusters
57
AUTOMATIC SLACK ADJUSTERS
While automatic slack adjuster designs vary in the
manner in which they are installed and operate, all are
designed to automatically maintain a predetermined
shoe-to-drum clearance or brake chamber stroke.
Some automatic slack adjusters adjust upon the
brake application stroke, others adjust upon release.
Automatic slack adjusters can greatly reduce manual
adjustments. Automatic slack adjusters do not
reduce the need for periodic maintenance.
Automatic Brake Adjuster Checking Procedures
If the brake adjuster is not maintaining the proper
applied stroke, before removing the brake adjuster,
check the condition of the foundation brake. If after
inspecting the foundation brake no apparent
problems are found, inspect the automatic brake
adjuster to determine if it is operating properly. The
inspection can be performed on or off
the vehicle using the following procedures.
Note:
- Block wheels to prevent vehicle from
rolling.
- Ensure system reservoir pressure is at
90-100 PSI.
- Check that push rod is fully retracted; apply
air to release spring brake.
- If air is not available, spring brake must be
manually caged back.
- Do not use air tools on brake adjuster!
Automatic Brake Adjuster Operational Check
Functional operation of the brake adjuster can be
performed on the vehicle by using the following
procedure:
- Block wheels to prevent vehicle
from rolling.
- Ensure reservoir pressure is at
90-100 psi.
- Check that the push rod is fully
retracted; apply air to release spring
brake. If air is not available, spring brake must
be manually caged back.
Manually de-adjust brakes (turn adjustment hex
counterclockwise one full turn) to create an excessive
lining to drum clearance condition. (A ratcheting
sound should occur.)
Make a full service brake application. On release,
allow sufficient time for air chamber to fully retract.
During the brake release, observe rotation of the
adjustment hex (attaching a wrench on the hex or
scribing the hex will make this rotation easier to see).
This rotation indicates that an excessive clearance
condition has been determined by the brake adjuster,
and it is making an adjustment to compensate. On
each subsequent brake release, the amount of
adjustment and push rod travel will be reduced until
the desired lining to drum clearance is achieved.
If rotation of the adjustment hex is not observed,
refer to Foundation Brake Operational Check and
Troubleshooting Procedures at www.haldex.com.
If foundation brake assembly checks out okay
and hex still does not turn, check control arm and
mounting bracket for possible worn, bent or broken
components. If the control arm and mounting bracket
check out okay, replace the adjuster and hardware
per Installation Instructions at www.haldex.com.
On Vehicle Inspection
58
5.2.9
SLACK ADJUSTERS (cont'd)
5.2.9.2
AUTOMATIC SLACK ADJUSTER MAINTENANCE (cont'd)
BRAKE ADJUSTMENT PROCEDURE
NOTE
All adjustments should be made
with cold brake drums and the
brakes fully released.
WARNING
To avoid possible injury, proper precautions
must be taken to prevent automatic actuation
of the brake chambers while adjusting slack
adjusters. Always block the wheels or mechanically secure the vehicle. Spring brakes
must be mechanically caged or released with
air. All brakes should be released.
Foundation Brake Operational Check and Troubleshooting
Note:
- Block wheels to prevent vehicle from grolling.
- Ensure system reservoir pressure is at
g90-100psi.
- Check that push rod is fully retracted; apply
air to release spring brake.
North American Commercial Vehicle Safety Alliance (CVSA) Uniform Vehicle Inspection Criteria
The applied stroke of the brake should be checked per CVSA guidelines at 90-100 PSI reservoir pressure.
Applied stroke should be at or less than the specified re-adjustment limits as follows:
59
Free Stroke
Measuring the Free Stroke
Free stroke is the amount of movement of the adjuster arm required to move the brake shoes against the drum.
With brakes released, measure from the face of the chamber to the center of the clevis pin “A” (fig. 13). Use a
lever to move the brake adjuster until the brake shoes contact the drum “B” (fig. 13). The difference between the
fully retracted and drum contact measurement “B”–“A” (fig. 13), is the free stroke. The free stroke range should
fall between 3/8"–3/4".
Free Stroke Within Range
If the free stroke is good, but the applied stroke is too long, there is probably a problem with the foundation
brake. Check the following and reference CVSA out-of-service criteria:
60
Stroke
the Range
FreeFree
Stroke
AboveAbove
the Range
If the free stroke is above the range and the applied stroke is too long, there is a problem with the foundation
If the free stroke is above the range and the applied stroke is too long, there is a problem
brakewith
or the
Check
the following:
theadjuster.
foundation
brake
or the adjuster. Check the following:
Component
Cause
Action
Camshaft
Camshaft bushings
Camshaft bushings
Air chamber return springs
Air chamber push rod
Binding
Excessive movement
Binding shaft
Broken, weak, missing
Binding on chamber housing
Air system
Shoe return springs
Automatic brake adjuster
Not exhausting completely
Broken, weak, missing
Unknown
Automatic brake adjuster
Unknown
Remove, replace, lubricate camshaft
Remove and replace cam bushings per OEM specs
Lubricate camshaft bushings or replace
Replace chamber
Check adjuster for proper shimming and air chamber
position for proper adjuster arm length
Check for cause of air problem and repair
Replace springs
Check automatic brake adjuster for proper
installation. Refer to Installation Instructions at
www.haldex.com.
Refer to Automatic Brake Adjuster Checking
Procedures and Operational Check at www.haldex.com.
Free Stroke Below the Range
If the free stroke is less than 3/8”, a dragging brake can occur. Check the following:
Component
Cause
Action
Wheel bearing
Automatic brake adjuster
Out of adjustment
Unknown
Automatic brake adjuster
Unknown
Readjust per OEM specs
Check automatic brake adjuster for proper control
arm position. Refer to Installation Instructions at
www.haldex.com.
Refer to Automatic Brake Adjuster Checking
Procedures and Operational Check at www.haldex.com.
Free Stroke = B minus A
Applied Stroke = C minus A
A
(Fully Retracted)
B
(Drum Contact Using a Lever)
C
(Brake Application at 90-100 PSI
reservoir pressure.)
Figure 13
Stroke Measurements
(taken from face of air
chamber to center of
clevis pin)
8
61
FAILURE ANALYSIS
Automatic Slack Adjuster Failure Analysis
If the power stroke is at or more than the maximum
stroke, measure free stroke to determine if the slack
adjuster is operational.
FREE STROKE MEASUREMENT
Free stroke is the amount of slack arm movement
required to move the brake shoes against the drum.
To measure free stroke, perform the following:
1. With brakes released, measure from the brake
chamber face to the center of the clevis pin.
2. With a lever, pry the slack adjuster arm untilthe
brake shoes contact the drum and measure the
slack adjuster movement (see Fig. 72).
3. The difference between the brake released and
applied measurements is the free stroke. The
free stroke should be 3/8" - 5/8". If the free
stroke is in the correct range, the out of spec
stroke is due to a foundation brake problem.
Check for missing or worn components, cracked
brake drums, or improper lining-to-drum contact.
If the free stroke is greater than recommended,
an automatic slack adjuster function test should
be performed.
62
Fig. 53
FREE STROKE
5.2.10
TRAILER ABS
Each trailer is designed with an
ABS (Automatic Braking System)
to increase the effectiveness of the
brakes during stopping. They system
consists of valves, sensors, exciter
rings and an Electronic Control Unit.
Review the brochures included in the
documentation package to become
familiar with the ABS system and
installation. The system is installed
on each axle and controlled by the
air system.
63
5.2.11 AIR CHAMBER/SPRING BRAKE
Air chambers mounted on the axle use
the air supply/pressure from the tractor
to apply the service brakes for stopping
the vehicle. In addition this air chamber
may be equipped with a spring brake that
applies the brake when the service side of
the brake loses air. The spring brake side
of the system is used as a parking and/or
emergency brake if the service side fails.
Spring brakes should not be serviced by
anyone in the field unless they have been
trained in the proper procedure. Do not
open the air chamber unless the spring is
caged or locked out. Do not work on the
brakes unless the springs are caged or
locked out. Do not move the trailer if the
springs are caged.
Schematic
When caging or locking out the spring
brakes, follow this procedure:
1. Place chocks in front of and behind
the trailer wheels.
2. Insert the release bolt, stored on the
side of the chamber, into the hole in
the head and through the piston.
3. Turn the release bolt clockwise until it
stops and locks.
4. Pull release bolt out as far as possible
and run the nut down while holding the
bolt in place.
5. Use a wrench to turn the release bolt
nut clockwise until the bolt extends
about 3 inches.
6. Be sure the release bolt is locked in
position.
7. The spring is now caged and the trailer
can be moved.
8. Always release the spring before
placing the trailer back in service.
64
Axle
Fig. 54 SPRING BRAKE
connect the axle to the main trailer frame and
SYSTEM
rb 5.2.12
the shockSUSPENSION
loads from the road.
Midland
rs can be equipped with either a mechanical or
5.2.12
SYSTEM
de The
suspension
system.
Either
system
well
suspension
systemSUSPENSION
is the group
of works
components
that
connect
the
axle
to
the
main
trailer
frame
and
will provide many years of trouble-free service.
The suspension
is theMidland
group of components
absorb the shock
loads fromsystem
the road.
that connect the axle to the main trailer frame and
trailers can be equipped with either a mechanical or
absorb the shock loads from the road. Midland
2.1air ride
AIRsuspension
RIDE
SUSPENSION
system. Either system works well
trailers can be equipped with either a mechanical or
and will provide
many
years of system.
trouble-free
air ride
suspension
Eitherservice.
system works well
r ride suspension
consists
and will
provide many years of trouble-free service.
springs
that
are
inflated
and
5.2.12.1 AIR RIDE SUSPENSION
urized by the 5.2.12.1
trailer air AIR
system
RIDE SUSPENSION
controlled
by
a
height
control
An air ride suspension consists
airare
rideinflated
suspension
. It
simpleAn
system
that andconsists
ofis
airasprings
that
of
air
springs
are inflated and
respressurized
minimal servicing
andthat
by the trailer
air system
pressurized by the trailer air system
tenance
to perform
and controlled
by awell.
height control
and controlled by a height control
valve. It is a valve.
simpleItsystem
that
is a simple system that
requires
minimal
servicing
and
lly inspect therequires
trailer at
the servicing and
minimal
maintenance
to
perform
well.
maintenance
tothe
perform well.
of the day or trip to check
ition of the suspension. Ensure
inspect
the trailer
Visually
inspectatthe
heVisually
ride height
is set
as
per thetrailer at the
start
of
the
or tripthe
to check the
start of the day or trip today
check
er specifications.
Also,ofcheck
condition
the
suspension.
condition of the suspension. Ensure Ensure
ose
fasteners
or damaged
that
theisride
is set as per
that
the ride height
setheight
as per
proper
specifications.
ponents.
Correct any problems
proper specifications.
Also, checkAlso, check
for
loose
fasteners
or damaged
e placing
trailer or
into
service.
for loosethe
fasteners
damaged
components. Correct any problems
ems
caught early
and corrected
components.
Correct
any the
problems
before
placing
trailer into service.
mize
cost
and
downtime.
before placing
the trailer
into early
service.
Problems
caught
and corrected
Problems caught
earlycost
andand
corrected
minimize
downtime.
minimize
cost
and
downtime.
y 5,000 miles (8,000 km)
Fig. 55
Every
5,000 miles
(8,000 km)
onthly, check the
clearance
around
all the
or
monthly,
check
the clearance around all the
Every
5,000
miles
(8,000
km)
ension system components. Correct any
suspension
system components.
Correct any
or monthly,
check
the clearance
around
all the
erence
problem.
Retorque
all the
fasteners
to fasteners to
interference
problem.
Retorque
all
the
suspension system components. Correct any
specified torque.
their specified torque.
interference problem. Retorque all the fasteners to
their specified torque.
SUSPENSION
HENDRICKSON
SUSPENSION
BOLT
TORQUEVALVES
VALVES
HENDRICKSON
TRAILER
SUSPENSION
BOLT
TORQUE
VALVES
HENDRICKSON
TAILER TAILER
SUSPENSION
BOLT
TORQUE
HENDRICKSON TAILER SUSPENSION BOLT TORQUE VALVES
65
Every 25,000 miles (40,000 km) or 3 months, visually
inspect all components and welds for cracks,
distortions or other damage. Repair or replace
all defective components before placing unit into
service.
Typical repairs include but are not limited to:
1. Air Spring Replacement:
Air springs are designed to be virtually troublefree throughout their life. Problems seldom occur
unless they are cut, punctured, abraded, pinched
or torn and then they must be replaced.
a. Block the wheels to prevent trailer movement.
b. Exhaust air from the suspension system.
a. Remove the upper and lower mounting bolts.
c. Raise and support the frame on safety
stands.
b. Remove old shock and install new one.
NOTE
Do not raise frame too high
unless shock absorbers are
installed to prevent overextending the air spring.
d. Disconnect the air lines to the air spring(s).
e. Loosen mounting bolts and remove air
spring(s).
f.
Install new air spring(s).
g. Tighten mounting bolts to their specified
torque of 50 ft. lbs. (68 N.m).
h. Install air lines and tighten to their specified
torque.
66
2. Shock Absorber Replacement:
Shock absorbers remove energy from the
suspension system as the trailer encounters holes
and bumps on the road surface. They also act as
a stop for the air springs to prevent the axle from
moving too far away from the frame and tearing
or damaging the air spring.
i.
Repeat on other air springs.
j.
Remove stands from under frame.
IMPORTANT
Use only correct original
equipment replacement parts.
Substitute parts do not work with
the suspension system.
c. Secure shock by tightening mounting bolts to
their specified torque of 250 ft. lbs. (338 N.m).
3. Pivot Bushing:
Pivot bushings are a very durable, long lasting
component. Bushing failures are rare and
should be attempted only when all other problem
causes have been eliminated. For pivot bushing
replacements please see your dealer or trailer
repair shop.
4. Air Control (Ride Height Control):
An air ride suspension system uses the air from
the tractor to pressurize the air springs. A single
height control valve is used to monitor the height
of the frame above the axle and add/exhaust
air from the system as required to maintain this
dimension. Normally this dimension is set for
your trailer and seldom changes.
The height control valve is located on one of the
axles and controls the adding/exhausting of air
to the air springs. As the dimension between the
frame and axle increases, the control lever moves
down and air is exhausted from the system. As
the dimension decreases, air is added to raise
the frame. All valves incorporate a 5 to 15
second time delay to minimize jerking or cycling.
Replace valve if not functioning properly.
System Schematic
Check ride height after first use and periodically
thereafter to maintain proper ride height. Improper
ride height can cause severe component damage
and void your warrenty. Maintaining correct ride
height is the responsibility of the operator.
There are two different ride heights. (15" and
17") All trailers with the exception of B-Train lead
are 17" ride height. The B-Train lead is 15". This
measurment is taken from the
centre of the axle to the underside of the frame.
NOTE: measure the axle that has the ride
height control mounted to it. The other axle(s)
may have more or less distance between the
frame and axle depending on height of fifth
wheel. If ride height is incorrect contact your
dealer.
Valve Schematic
Valve
Fig. 56
RIDE HEIGHT CONTROL
67
5.2.13
AIR SYSTEM
Trailers are equipped with an air system, that
is pressurized by a compressor on the tractor,
for operating the brakes and air suspension (if
so equipped). All components must be in good
condition for the system to function and perform
as intended. The air system must be inspected
to be kept in good condition and functional
checks performed to be sure it is operating as
required.
5.2.13.1
AIR SYSTEM INSPECTION
The pre-trip or pre-start inspection include several air
system related checks, inspections or tasks including
but not limited to:
Daily
1. Check that the glad hands are clean and in good
condition. Check seals in glad hand Clean, repair
or replace as required.
2. Check that the air hoses between the tractor and
the trailer are routed to prevent rubbing, chaffing
or pinching. Reroute to correct condition if
required.
3. Drain moisture from all air tanks. Pull on the
cable attached to drain valve on the bottom of
each tank until the water or spray no longer can
be seen.
4. Check that all the lines and hoses conveying
air along the frame are tied up and secured to
prevent dragging, scuffing or snagging. Tie up
or protect as required to correct the condition.
Damaging an air system component can cause
a sudden loss of pressure and result in a loss of
service brakes.
IMPORTANT
Tanks must be drained daily in high humidity and cold
temperature conditions to prevent getting water or ice
in the system. During cold weather operation use only
recommended air line anti freeze in the trailer air system.
Alcohol or methyl hydrate is not to be used because they
will remove vital lubricants causing premature failures
of valves and components. Traces of these products
will void any warranty consideration.
IMPORTANT
New FMVSS-121 regulations mandate higher pressures
in the supply line to insure proper brake operation. Set
the compressor pressure for cut-in to 105 psi and cutout to 120 psi. Do not use additives in the air systems.
5.2.13.2
AIR SYSTEM FUNCTION
A vehicle air system is a combination of the
components on the tractor and the trailer. All must
be maintained in good condition for the entire system
to function as required. Although a visual check will
indicate the outer condition of the components, it
does not indicate the leaks or responsiveness of the
system. To evaluate the integrity and responsiveness
of the system, perform these functional checks:
1. Attach the trailer to a tractor and connect all the
air and electrical lines.
2. Block wheels.
3. Stop tractor engine and exhaust air from all tanks.
4. Start engine and run at fast idle (1200-1500 RPM)
to charge the air system.
Verify that:
a. Low pressure alarm goes off when the
system
pressure drops below 50 psi.
b. Increasing the system pressure between 50
psi and 80 psi takes less than 3 minutes.
c. The compressor cuts out when the system
pressure exceeds 120 psi.
d. Fan brakes to use air. Compressor must
engage when system pressure drops below
105 psi.
NOTE
Release spring brakes before
fanning service brakes.
5. Push emergency valve to charge trailer system.
Apply and release service brakes.
6. Build system above 120 psi and stop engine.
Verify that:
a. Main tank pressure does not drop more than
18 psi when brakes are fully applied using
brake pedal. If pressure drop exceeds 18 psi,
adjust brakes and recheck.
b. System pressure should not drop more than 4
psi per minute. Listen for audible leaks.
c. Release foot valve, fan treadle to drop main
reservoir pressure. Brakes should dynamite
automatically when the pressure drops below
60 psi.
Adjust or repair system until these conditions are
met.
68
5.2.14
ELECTRICAL SYSTEM
All trailers are equipped with an electrical
system for providing power for lights and
electrical controls. All components are designed
to minimize the effects of foul weather and
adverse operating conditions. However, it is the
responsibility of the operator to check and verify
that all components are in good condition and
functioning as intended.
During the daily or pre-trip inspection, always
verify that each light functions as required. It
may be helpful to work with another individual
to verify the function of the brake or turn signal
lights. A properly functioning electrical system
is the only way an operator can communicate
his intentions to other drivers. Checking the
electrical system includes but is not limited to:
Electrical Connectors
1. Replace any bulb that is burned out.
2. Clean all reflective lenses. Replace any that
are cracked or broken.
3. Clean all connections and terminals to a light
that is flickering.
4. Reroute and secure any wires or cables that
are dangling or have snagged on something.
5. Check the integrity of the seal around each
light. Replace any seal that is cracked or
damaged.
Side Signal
6. Annually (or more often as necessary) check
and re-seal all connectors with a nonconductive grease.
Rear
Fig. 57
LIGHTING
69
6
TROUBLE SHOOTING
The Midland SandRunner Trailer uses a clam discharge gate for unloading material as required. It is a simple and
reliable system that requires minimal maintenance.
In the following section, we have listed problems, causes and solutions to the problems that you may encounter.
If you encounter a problem that is difficult to solve, even after having read through this trouble shooting section,
and through the specifically related components manufacturer’s manuals, please call your local Midland dealer
or distributor. Before you call, please have this Operator’s Manual and the serial number from your trailer ready.
PROBLEM
CAUSE
SOLUTION
Trailer "Dog-Tracks"...
Trailer out of alignment.
Realign per procedure provided by
the suspension manufacturer.
70
PROBLEM
CAUSE
SOLUTION
Over or under inflation.
Inflate to proper pressure.
Loose wheel stud nuts or
clamps.
Tighten wheel stud nuts or clamps.
Tires
High or uneven tire wear.
Loose or tight wheel bearing.
Axle bent or out of alignment.
Tires not properly matched.
Improper acting brakes.
Scuffed tires.
Wobbly tires.
Dog tracking.
Loss of tire air pressure.
Adjust bearings.
Straighten, align or replace axle.
Match tires.
Correct brakes as required.
Rapid stopping.
Apply brakes slowly when
approaching stops.
High speed.
Reduce speed.
Over or under inflation.
Inflate to proper pressure.
Excessive speed on turns.
Reduce speed.
Tire wobble due to uneven rim
clamping.
Torque tighten all rim clamps.
Worn or damaged wheel
bearings.
Replace bearings.
Bent wheel or rim.
Replace wheel or rim.
Bent axle.
Replace or straighten axle.
Leaf spring broken.
Replace leaf or complete spring.
Bent axle.
Replace or straighten axle.
Frame or suspension (axles) out
of alignment.
Straighten frame or align axles.
Puncture in tire.
Repair or replace tire.
Faulty valve or valve core.
Replace valve assembly or core.
Wheel or rim damage.
Replace wheel or rim.
71
PROBLEM
CAUSE
SOLUTION
Bad connection.
Check electrical system circuits.
Frayed wires.
Repair as required.
Battery on tractor not sufficiently
charged.
Charge battery.
Damaged or disconnected wire
on ground cable.
Repair or replace cable.
Poor ground at sockets.
Repair as necessary.
Broken main harness.
Repair or replace.
Junction box failure.
Replace junction box.
Frayed wires.
Repair as required.
Damaged or disconnected
ground cable.
Repair or replace cable as required.
Electrical
Lights flicker or do not
come on.
Complete loss of trailer lights.
Loose or corroded connection in
ground lead between tractor and
trailer.
Lights flash improperly or
appear to be crossed.
72
Internal short in junction box.
Repair or replace.
Replace junction box.
PROBLEM
CAUSE
SOLUTION
Air leak.
Check air line fittings and hose
connections on service or supply
line.
Air System
Excessive compressor
cycling.
Check service chamber at clamp
housing, push rod for damage.
Check service chamber diaphragm.
Check emergency chamber clamp
and vent holes for leakage.
Repair or replace air chamber as
required.
Check FFVII brake valve. Repair or
replace as required.
Trailer brakes slow and
sluggish.
System or component failure.
Check slack adjuster and chamber/
spring brake push rod alignment for
interference.
Assure slack adjuster and chamber/
spring brake push rod angle 90°
applied with proper adjustment.
Assure open lines - no kinks, bends,
closed shut-off cocks, restrictions,
excessive elbows.
Assure adequate tractor brake
function.
Have authorized service center
check for adequate pressure and
timing balance relative to tractor/
trailer application.
73
PROBLEM
CAUSE
SOLUTION
System or component failure
Assure emergency line exceeds 120
psi pressure; check and maintain
governor at max. cut-in.
Air System (cont'd)
Trailer brakes drag.
Check slack adjuster and chamber/
spring brake push rod alignment for
interference.
Assure slack adjuster and chamber/
spring brake push rod angle 90°
applied with proper adjustment.
Assure open lines - no kinks, bends,
closed shut-off cocks, restrictions,
excessive elbows.
Check for trapped service
air pressure at trailer service/
delivery hoses. If air pressure is
noted, check for full release of all
application valves (tractor/truck/
trailer).
Trailer brakes won't apply
(service).
System or component failure.
Check air delivery to emergency
system.
Check air delivery to service
gladhand.
Check air delivery to air chamber
or spring brake.
Check air delivery to all reservoirs
at system working pressure.
Check slack adjuster and chamber/
spring brake push rod alignment
for interference.
Check slack adjuster and chamber/
spring brake push rod angle 90°
applied with proper adjustment.
Park/emergency brakes won't
release.
System or component failure.
Check air jumper hoses are not
crossed between tractor and trailer.
Check air delivery to emergency
gladhands exceeds 120 psi.
Check air delivery to FFV valve.
Check air delivery to all reservoirs
at system working pressure.
74
PROBLEM
CAUSE
SOLUTION
System or component failure
(cont'd).
Check open lines - no kinks, bends,
closed shut-off cocks, restrictions,
excessive elbows.
Air System (cont'd)
Park/emergency brakes won't
release (cont'd).
Check that brake shoes are not
frozen to drums.
Park/emergency brakes won't
hold.
System or component failure.
Check slack adjuster and chamber/
spring brake push rod alignment for
interference.
Assure slack adjuster and chamber/
spring brake push rod angle 90°
applied with proper adjustment.
Air reservoir leaks or loose
mounting.
System or component failure.
Replace/use rubber grommets with
integral brackets.
Semi-trailer "Runs-Up" on
tractor.
Check brake linkage.
Assure slack adjuster and
chamber/spring brake push rod
angle 90° applied with proper
adjustment.
Check gladhand connection.
Assure open lines - no kinks,
bends, closed shut-off cocks,
restrictions, excessive elbows.
Have authorized service center
check for adequate pressure and
timing balance relative to tractor/
trailer application.
Poor braking performance.
Uneven brakes.
Check slack adjuster and chamber/
spring brake push rod angle 90°
applied with proper adjustment.
Check slack adjuster and chamber/
spring brake push rod angle 90°
applied with proper adjustment.
Check open lines - no kinks, bends,
closed shut-off cocks, restrictions,
excessive elbows.
Check a leak free system by
applying service brake and
inspecting.
75
PROBLEM
CAUSE
SOLUTION
Trailer brake lining wear
excessive.
Have authorized service center
check for adequate pressure and
timing balance relative to tractor/
trailer application.
Air System (cont'd)
Poor braking performance
(cont'd).
Proceed per problem "trailer
brakes drag."
Trailer brakes slow to apply.
Check slack adjuster and chamber/
spring brake push rod angle 90°
applied with proper adjustment.
Check air delivery to all reservoirs
at system working pressure.
Check open lines - no kinks,
bends, closed shut-off cocks,
restrictions, excessive elbows.
Have authorized use of "jumper
hose analyser" and duplex gauge
to pin-point brake imbalance.
Check functional return spring in
service chamber or spring brake.
Check open lines - no kinks,
bends, closed shut-off cocks,
restrictions, excessive elbows.
Trailer service brakes slow to
release.
Have authorized use of "jumper
hose analyser" and duplex gauge
to pin-point brake imbalance.
Slack adjuster not autoadjusting.
Check for damaged actuator rod.
Replace as required.
Slack adjuster internal components
seized. Replace.
76
Cracked housing.
Replace slack adjuster.
Worn clevis pin bushing.
Replace bushing
PROBLEM
CAUSE
SOLUTION
Full function valve (FFV) leaks
at exhaust port with all brakes
released.
Replace FFV valve.
Full function valve (FFV) leaks at
exhaust port with service brakes
applied.
Replace FFV valve.
Spring parking brake (service
only service chamber side of
spring brake) drags or won't
release.
Check for:
- Improper adjustment, restriction
or broken line.
- Diaphragm failure.
- System pressure too low (120 psi
min).
- Improper manual release.
- Broken return spring (spring
side).
- Broken power spring.
- Replace entire unit or piggy-back
emergency section.
Spring parking brake (service
only service chamber side
of spring brake) leaks when
pressurized for park brake
release.
Check for:
- Ruptured spring side diaphragm.
- Hose leaks.
Air System (cont'd)
Poor braking performance
(cont'd).
77
7
SPECIFICATIONS
7.1
BOLT TORQUE
CHECKING BOLT TORQUE
The tables shown below give correct torque values for various bolts and capscrews. Tighten all bolts to the
torques specified in chart unless otherwise noted. Check tightness of bolts periodically, using bolt torque chart
as a guide. Replace hardware with the same strength bolt.
ENGLISH TORQUE SPECIFICATIONS
Bolt Torque*
Bolt
SAE 5
SAE 2
SAE 8
Diameter
(N.m)
(lb-ft)
(N.m) (lb-ft)
(N.m) (lb-ft)
"A"
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
8
13
27
41
61
95
128
225
230
345
6
10
20
30
45
60
95
165
170
225
12
25
45
72
110
155
215
390
570
850
9
19
33
53
80
115
160
290
420
630
17
36
63
100
155
220
305
540
880
1320
12
27
45
75
115
165
220
400
650
970
METRIC TORQUE SPECIFICATIONS
Bolt Torque*
Bolt
10.9
8.8
Diameter
(N.m) (lb-ft) (N.m) (lb-ft)
"A"
M3
M4
M5
M6
M8
M10
M12
M14
M16
M20
M24
M30
M36
.5
3
6
10
25
50
90
140
225
435
750
1495
2600
.4
2.2
4
7
18
37
66
103
166
321
553
1103
1917
1.8
4.5
9
15
35
70
125
200
310
610
1050
2100
3675
1.3
3.3
7
11
26
52
92
148
229
450
774
1550
2710
Torque figures indicated above are valid for non-greased or non-oiled threads and heads unless otherwise
specified. Therefore, do not grease or oil bolts or capscrews unless otherwise specified in this manual. When
using locking elements, increase torque values by 5%.
* Torque value for bolts and capscrews are identified by their head markings.
78
8
INDEX
I
PAGE
Introduction .....................................................1
O
Operation Guidelines .....................................11
Air System ................................................24
Tanks ...................................................24
Break-In ....................................................13
Controls ....................................................15
Discharge Gates .......................................23
Hooking Up/Unhooking ............................20
Hooking Up .........................................20
Unhooking ...........................................22
Loading/Unloading ...................................25
Loading ...............................................25
Unloading ............................................26
Pre-Operation Vehicle Inspection
Procedure ............................................17
Terminology ..............................................12
To the New Operator or Owner ................11
Transporting .............................................26
Braking Guidelines ..............................27
Operating Instructions .........................26
Tires .....................................................28
S
Safety ..............................................................2
General Safety ............................................3
Loading Safety ...........................................5
Maintenance Safety....................................4
Operating Safety ........................................4
Safety Signs ...............................................5
Sign-Off Form .............................................6
Tire Safety ..................................................5
Travel Safety ...............................................5
Safety Sign Locations .....................................7
PAGE
Service and Maintenance ..............................29
Periodic Maintenance and Adjustments ..39
Air Chamber/Spring Brake ..................64
Air System ...........................................68
Air System Function .......................68
Air System Inspection ....................68
Axle Alignment ....................................43
Brakes .................................................53
Electrical System .................................69
Fifth Wheel ..........................................42
Kingpin and Oscillating Fifth Wheel
Plate ...............................................41
Slack Adjusters ...................................56
Suspension System.............................65
Air Ride Suspension.......................65
Tires .....................................................51
Torque Specification Summary ...........39
Trailer ABS ...........................................63
Wheels .................................................49
Wheel Hubs/Bearings..........................45
Service......................................................29
Fluids and Lubricants ..........................29
Greasing ..............................................29
Service Record Summary (Lube).........38
Servicing Intervals ...............................30
Specifications ................................................78
Bolt Torque ...............................................78
T
Trouble Shooting ...........................................70
79
MIDLAND MANUFACTURING LIMITED
BOX 249
ROSENORT, MANITOBA
CANADA R0G 1W0
PHONE (204) 746-2348
TOLL FREE 1-800-827-7023
FAX (204) 746-2286
www.midlandtrailers.com
PRINTED IN CANADA
ISSUE DATE: APRIL, 2023
REPRINT DATE: DECEMBER, 2023
PART NUMBER: 0200027