STMicroelectronics NUCLEO-H563ZI User Manual

UM3115
User manual
STM32H5 Nucleo-144 board (MB1404)
Introduction
The STM32H5 Nucleo-144 board based on the MB1404 reference board (order code NUCLEO-H563ZI) provides an affordable
and flexible way for users to try out new concepts and build prototypes, by choosing from the various combinations of
performance and power consumption features provided by the STM32H5 series microcontroller.
The ST Zio connector, which extends the ARDUINO® Uno V3 connectivity, and the ST morpho headers provide an easy
extension of the functionality of the STM32 Nucleo open development platform with a wide choice of specialized shields.
The STM32H5 Nucleo-144 board does not require any separate probe as it integrates the STLINK-V3EC debugger/
programmer.
The STM32H5 Nucleo-144 board comes with the STM32 comprehensive free software libraries and examples available with the
STM32CubeH5 MCU Package.
Figure 1. NUCLEO-H563ZI top view
Figure 2. NUCLEO-H563ZI bottom view
Pictures are not contractual.
UM3115 - Rev 2 - August 2023
For further information contact your local STMicroelectronics sales office.
www.st.com
UM3115
Features
1
Features
•
STM32H563ZIT6 microcontroller based on the Arm® Cortex®-M33 core, featuring 2 Mbytes of flash
memory and 640 Kbytes of SRAM in an LQFP144 package
Ethernet compliant with IEEE-802.3-2002
•
•
•
•
•
USB Type-C® (sink only)
Three user LEDs
Reset and user push-buttons
32.768 kHz LSE crystal oscillator
Board connectors:
•
–
•
•
•
•
Note:
UM3115 - Rev 2
USB Type-C®
–
ST Zio connector including ARDUINO® Uno V3 expansion connector
–
ST morpho extension pin headers for full access to all STM32 I/Os
Flexible power-supply options: ST-LINK USB VBUS, USB connector, or external sources
On-board STLINK-V3EC debugger/programmer with USB re-enumeration capability: mass storage, Virtual
COM port, and debug port
Comprehensive free software libraries and examples available with the STM32CubeH5 MCU Package
Support of a wide choice of Integrated Development Environments (IDEs) including IAR Embedded
Workbench®, MDK-ARM, and STM32CubeIDE
Arm is a registered trademark of Arm Limited (or its subsidiaries) in the US and/or elsewhere.
page 2/44
UM3115
Ordering information
2
Ordering information
To order the STM32H5 Nucleo-144 board, refer to Table 1. Additional information is available from the datasheet
and reference manual of the target STM32.
Table 1. Ordering information
Order code
Board reference
Target STM32
NUCLEO-H563ZI
MB1404(1)
STM32H563ZIT6
1. Subsequently named main board in the rest of the document.
2.1
Products and codification
The meaning of the codification is explained in Table 2.
Table 2. Codification explanation
NUCLEO-XXYYZT
Description
Example: NUCLEO-H563ZI
XX
MCU series in STM32 32-bit Arm Cortex MCUs
STM32H5 series
YY
MCU product line in the series
STM32H563/573
Z
STM32 package pin count
T
STM32 flash memory size:
•
I for 2 Mbytes
144 pins
2 Mbytes
In this document, for any information that is common to all sales types, the references are noted as the STM32H5
Nucleo-144 board.
UM3115 - Rev 2
page 3/44
UM3115
Development environment
3
Development environment
3.1
System requirements
Note:
•
Multi‑OS support: Windows® 10, Linux® 64-bit, or macOS®
•
USB Type-A or USB Type-C® to USB Type-C® cable
macOS® is a trademark of Apple Inc., registered in the U.S. and other countries and regions.
Linux® is a registered trademark of Linus Torvalds.
Windows is a trademark of the Microsoft group of companies.
3.2
Development toolchains
•
IAR Systems® - IAR Embedded Workbench®(1)
•
•
Keil® - MDK-ARM(1)
STMicroelectronics - STM32CubeIDE
1. On Windows® only.
3.3
Demonstration software
The demonstration software, included in the STM32Cube MCU Package corresponding to the on-board
microcontroller, is preloaded in the STM32 flash memory for easy demonstration of the device peripherals in
standalone mode. The latest versions of the demonstration source code and associated documentation can be
downloaded from www.st.com.
UM3115 - Rev 2
page 4/44
UM3115
Conventions
4
Conventions
Table 3 provides the conventions used for the ON and OFF settings in the present document.
Table 3. ON/OFF convention
UM3115 - Rev 2
Convention
Definition
Jumper JPx ON
Jumper fitted
Jumper JPx OFF
Jumper not fitted
Jumper JPx [1-2]
Jumper fitted between Pin 1 and Pin 2
Solder bridge SBx ON
SBx connections closed by 0 Ω resistor
Solder bridge SBx OFF
SBx connections left open
Resistor Rx ON
Resistor soldered
Resistor Rx OFF
Resistor not soldered
Capacitor Cx ON
Capacitor soldered
Capacitor Cx OFF
Capacitor not soldered
page 5/44
UM3115
Quick start
5
Quick start
The STM32H5 Nucleo-144 board is a low-cost and easy-to-use development kit, to evaluate and start
development quickly with an STM32H5 series microcontroller in an LQFP 144-pin package.
Before installing and using the product, accept the Evaluation Product License Agreement from the www.st.com/
epla webpage. For more information on the STM32H5 Nucleo-144 board and demonstration software, visit the
www.st.com/stm32nucleo webpage.
5.1
Getting started
Follow the sequence below to configure the STM32H5 Nucleo-144 board and launch the demonstration
application (refer to Figure 4 and Figure 5 for component location):
1.
Check the jumper position on the board as described in Table 4.
Table 4. Default jumper configuration
2.
3.
4.
5.
6.
7.
UM3115 - Rev 2
Jumper
Definition
Position
Comment
JP1
External debug
OFF
-
JP2
Power source selection
[1-2]
STLK (5V_STLK from ST-LINK)
JP3
STLK_RST
OFF
-
JP4
VDD_MCU power selection
JP5
IDD measurement
ON
MCU current measurement
JP6
Ethernet transmit data1
ON
RMII_TXD1
[1-2] (default)
VDD_MCU supplied with 3V3_VDD
[2-3] (optional)
VDD_MCU supplied with 1V8_VDD
For the correct identification of the device interfaces from the host PC and before connecting the board,
install the Nucleo USB driver available on the www.st.com/stm32nucleo website.
Power the board by connecting the STM32H5 Nucleo-144 board to a PC with a USB Type-A or USB TypeC® cable through the USB connector (CN1). As a result, the PWR green LED (LD5), the COM LED (LD4),
and the PWR LED (LD6) light up, while the three user LEDs (LD1 to LD3) blink.
Press the user blue button (B1).
Observe how the blinking frequency of the three LEDs (LD1 to LD3) changes, according to the number of
clicks on the user button (B1).
The software demonstration and the several software examples that allow the user to exercise the Nucleo
features, are available at the www.st.com website.
Develop your application using the available examples.
page 6/44
UM3115
Hardware layout and configuration
6
Hardware layout and configuration
The STM32H5 Nucleo-144 board is designed around an STM32H5 series microcontroller in a 144-pin LQFP
package.
Figure 3 shows the connections between the STM32H5 and its peripherals (STLINK-V3EC, push-buttons, LEDs,
USB, Ethernet, ST Zio connectors, and ST morpho headers).
Figure 4 and Figure 5 show the location of these features on the STM32H5 Nucleo-144 board.
The mechanical dimensions of the board are shown in Figure 6.
Figure 3. Hardware block diagram
USB Type-C®
connector
Note:
UM3115 - Rev 2
SWD
VCP
UART
I/O
LED1
LED2
LED3
I/O
STM32
microcontroller
USB
RMII
USB Type-C®
connector
RJ45
connector
ST morpho extension header
VCP
UART
Reset
button
(B2)
DT59060V1
User
button
(B1)
SWD
Zio connector
Zio connector
ST morpho extension header
Embedded
STLINK-V3EC
VCP: Virtual COM port
SWD: Serial Wire Debug
page 7/44
UM3115
STM32H5 Nucleo-144 board layout
6.1
STM32H5 Nucleo-144 board layout
Figure 4. STM32H5 Nucleo-144 board top layout
ST-LINK RST (JP3)
ST-LINK USB Type-C® connector (CN1)
ST-LINK power status LED (LD6)
ST-LINK COM LED (LD4)
MIPI20 connector (CN5)
5V Power LED (LD5) (green)
Power source selection (JP2)
User LEDs (LD1-LD3)
External debug (JP1)
VDD_MCU power selection (JP4)
IDD measurement (JP5)
Zio connector (CN7)
Zio connector (CN8)
STM32 microcontroller (U14)
ST morpho pin header (CN12)
ST morpho pin header (CN11)
User button (B1)
User USB connector (CN13)
Zio connector (CN10)
Reset button (B2)
Ethernet RJ45 connector
(CN14)
USB VBUS LED (LD7)
UM3115 - Rev 2
page 8/44
DT59061V1
Zio connector (CN9)
UM3115
STM32H5 Nucleo-144 board layout
Figure 5. STM32H5 Nucleo-144 board bottom layout
DT59062V1
IOREF power
selection
(SB16, SB25)
UM3115 - Rev 2
page 9/44
UM3115
Mechanical drawing
6.2
Mechanical drawing
Figure 6. STM32H5 Nucleo-144 board mechanical drawing (in millimeters)
DT59087V1
133.34 mm
70.00 mm
UM3115 - Rev 2
page 10/44
UM3115
Embedded STLINK-V3EC
7
Embedded STLINK-V3EC
The chapter below gives some information about the implementation of STLINK-V3EC.
For more details on STLINK-V3EC such as LEDs management, drivers, and firmware, refer to the technical note
Overview of ST-LINK derivatives (TN1235).
For information about the debugging and programming features of STLINK-V3EC, refer to the user manual
STLINK-V3SET debugger/programmer for STM8 and STM32 (UM2448).
Description
There are two different ways to program and debug the onboard STM32 MCU.
•
•
Using the embedded STLINK-V3EC programming and debugging tool on the NUCLEO-H563ZI board.
Using an external debug tool connected to the CN5 MIPI20 connector (SWD/JTAG/TRACE)
The STLINK-V3EC facility for debugging and flashing is integrated into the STM32H5 Nucleo-144 board.
Supported features in STLINK-V3EC:
•
•
•
•
•
•
•
•
5 V/500 mA power supply capability through the USB Type-C® connector (CN1)
USB 2.0 high-speed-compatible interface
JTAG and Serial Wire Debug (SWD) with Serial Wire Viewer (SWV)
Virtual COM port (VCP)
1.7 to 3.6 V application voltage
COM status LED, which blinks during communication with the PC
Power status LED giving information about STLINK-V3EC target power.
Overvoltage protection (U2) with current limitation
Two tricolor LEDs (green, orange, and red) provide information about STLINK-V3EC communication status (LD4)
and STLINK-V3EC power status (LD6).
For detailed information about the management of these LEDs, refer to the technical note Overview of ST-LINK
derivatives (TN1235).
Drivers
The installation of drivers is not mandatory from Windows 10® but allocates an ST-specific name to the ST-LINK
COM port in the system device manager.
For detailed information on the ST-LINK USB drivers, refer to the technical note Overview of ST-LINK derivatives
(TN1235).
STLINK-V3EC firmware upgrade
STLINK-V3EC embeds a firmware upgrade (stsw-link007) mechanism through the USB-C® port. As the
firmware might evolve during the lifetime of the STLINK-V3EC product (for example to add new functionalities, fix
bugs, and support new microcontroller families), it is recommended to keep the STLINK-V3EC firmware up to
date before starting to use the NUCLEO-H563ZI board. The latest version of this firmware is available from the
www.st.com website.
For detailed information about firmware upgrades, refer to the technical note Overview of ST-LINK derivatives
(TN1235).
Using an external debug tool to program and debug the on-board STM32
Before connecting any external debug tool to the MIPI20 debug connector (CN5), the SWD and VCP signals from
STLINK-V3EC must be isolated. For this, fit the jumper on JP1. It disables the U1 level shifter and isolates SWD
and VCP signals from STLINK-V3EC. The configuration of the JP1 is explained in Table 5.
Once the jumper is fitted on JP1, an external debug tool can be connected to the MIPI20 debug connector (CN5).
The two level shifters U1 and U10 allow compatibility between the target MCU signals (1V8 or 3V3) and the
STLINK-V3EC signals (3V3). They are used on VCP and SWD interfaces to offer a debug capability when
operating the target MCU at 1V8.
UM3115 - Rev 2
page 11/44
UM3115
Embedded STLINK-V3EC
Table 5. JP1 configuration
Jumper
Definition
JP1
Setting
Comment
ON [1-2]
An external debugger connected to the
MIPI20 connector (CN5) can be used.
The level shifter (U1) is in high
impedance (high‑Z).
Debugger selection
STLINK-V3EC no longer drives the
embedded STM32
The embedded STLINK-V3EC is
selected (default configuration).
OFF
Note:
The MIPI20 TRACE connector supports 1V8 or 3V3 for target reference voltage. When using the external debug
connector (CN5), STLINK-V3EC can be used to supply the board through the CN1 USB Type-C® connector.
Otherwise, another power supply source can be used as described in Section 8 Power supply.
Figure 7. Connecting an external debug tool to program the on-board STM32
5V power supply selection
(JP2)
STLINK-V3EC USB connector
(CN1)
MIPI20 connector
(SWD/JTAG/TRACE)
(CN5)
DT59063V1
External debugger selection
(JP1)
Table 6. MIPI20 debug connector (CN5) pinout
UM3115 - Rev 2
MIPI20
pin
CN5
1
VTref
2
SWDIO/JTMS
3
GND
4
SWCLK/JCLK
Designation
Target reference voltage (fed from VDD)
Target SWDIO using SWD protocol or target JTMS using JTAG protocol
Ground
Target SWCLK using SWD protocol or target JCLK using JTAG protocol
5
GND
6
JTDO/SWO
Ground
7
KEY
Not connected
8
JTDI
Not used by SWD protocol, target JTDI (T_JTDI) using JTAG protocol, only for external
tools
9
GND
Ground
10
NRST
Target NRST using SWD protocol or target JTMS (T_JTMS) using JTAG protocol
Target SWO using SWD protocol or target JTDO using JTAG protocol
page 12/44
UM3115
Embedded STLINK-V3EC
UM3115 - Rev 2
MIPI20
pin
CN5
11
TgtPwr
12
TRACECLK
13
TgtPwr
14
TRACED0
15
GND
16
TRACED1
17
GND
18
TRACED2
19
GND
20
TRACED3
Designation
5 V target power to the target MCU–To be disconnected (SB84 OFF)
Trace clock
5 V target power to the target MCU–To be disconnected (SB84 OFF)
Trace Data0
Ground
Trace Data1
Ground
Trace Data2
Ground
Trace Data3
page 13/44
UM3115
Power supply
8
Power supply
Six different sources can provide the power supply to NUCLEO-H563ZI:
•
•
•
•
•
•
A host PC connected to CN1 through a USB cable (default configuration)
An external 7 to 12 V power supply connected to CN8 pin 15 or CN11 pin 24 (VIN)
An external 5 V power supply connected to CN11 pin 6 (5V_EXT)
An external 5 V USB charger (VBUS_STLK) connected to CN1
A host PC connected to CN13 through a USB cable
An external 3.3 V power supply (3V3) connected to CN8 pin 7 or CN11 pin 16
In case VIN, 5V_EXT, or 3V3 is used to power the STM32H5 Nucleo-144 board, this power source must comply
with the EN-60950-1: 2006+A11/2009 standard and must be safety extra low voltage (SELV) with limited power
capability.
In case the power supply is +3.3 V, STLINK-V3EC is not powered and cannot be used.
8.1
Power supply input from STLINK-V3EC USB connector: 5V_STLK (default
configuration)
The 5 V signal on the STLINK-V3EC USB connector (CN1) can power the STM32H5 Nucleo-144 board and its
shield. To select the 5V_STLK power source, JP2 must be set on [1-2] ‘STLK’ (refer to Figure 8).
This is the default configuration.
Figure 8. Power supply input from STLINK-V3EC USB connector with PC (5 V, 500 mA maximum)
PC
5V
DT59064V1
5V
3V3
If the USB enumeration succeeds, the ST-LINK power is enabled, by asserting the T_PWR_EN signal from
STLINK-V3EC. This pin is connected to a power switch (U2), which powers the board. The power switch also
features a current limitation to protect the PC in case of a short circuit onboard. If an overcurrent (more than
500 mA) happens onboard, the POWER LED STATUS (LD6) is lit in red color.
The STLINK-V3EC USB connector (CN1) can power the Nucleo board with its shield.
•
•
If the host can provide the required power, the power switch and the green LED (LD5) are turned ON.
Thus, the Nucleo board and its shield can consume up to 500 mA current, but no more.
If the host is not able to provide the requested current, the enumeration fails.
Therefore, the power switch (U2) remains OFF and the MCU part including the extension board is not powered.
As a consequence, the green LED (LD5) remains turned OFF. In this case, it is mandatory to use an external
power supply.
Warning:
UM3115 - Rev 2
In case the maximum current consumption of the STM32H5 Nucleo-144 board and its shield
boards exceed 500 mA, it is mandatory to power the STM32H5 Nucleo-144 board, using an
external power supply connected to 5V_EXT, VIN, or 3V3.
page 14/44
UM3115
External power supply input from VIN (7 to 12 V, 800 mA maximum)
8.2
External power supply input from VIN (7 to 12 V, 800 mA maximum)
When the STM32H5 Nucleo-144 board is power supplied by VIN (refer to Table 7 and Figure 9, the JP2 jumper
must be fitted on [3-4] (VIN 5V).
The STM32H5 Nucleo-144 board and its shield boards can be powered in three different ways from the VIN
external power supply, depending on the used voltage. The three power sources are summarized in Table 7.
Table 7. External power sources VIN (7 to 12 V)
Input
power
name
VIN
Connector pins
CN8 pin 15
CN11 pin 24
Maximum
current
Voltage
Limitation
From 7 to 12 V only and input current capability is
linked to input voltage:
7 to 12 V
800 mA
•
•
•
800 mA input current when VIN = 7 V
450 mA input current when 7 V < VIN < 9 V
250 mA input current when 9 V < VIN < 12 V
Figure 9. Power supply input from VIN (7 to 12 V, 800 mA maximum)
5V
3V3
DT59065V1
VIN < 12V
8.3
External power supply input 5V_EXT (5 V, 1.3 A maximum)
When the STM32H5 Nucleo-144 board is power supplied by 5V_EXT (refer to Figure 10 and Table 8, the JP2
jumper must be fitted on [5-6] (E5V).
Table 8. Power supply input from 5V_EXT (5 V, 1.3 A)
Note:
UM3115 - Rev 2
Input power
name
Connector pins
Voltage
Maximum current
5V_EXT
CN11 pin 6
4.75 to 5.25 V
1.3 A
Refer to Using an external debug tool to program and debug the on-board STM32 about debugging when using
an external power supply.
page 15/44
UM3115
External power supply input from a USB charger (5 V)
Figure 10. Power supply input from 5V_EXT (5 V, 1.3 A maximum)
5V
3V3
8.4
DT59066V1
5V_EXT
External power supply input from a USB charger (5 V)
When the STM32H5 Nucleo-144 board is power supplied by a USB charger on CN1 (refer to Figure 11 and
Table 9), the JP2 jumper must be set on [7-8] (CHGR).
Table 9. External power source CHGR (5 V)
Input power
name
Connector pins
Voltage
Maximum current
CHGR
CN1
5V
-
Figure 11. Power supply input from STLINK-V3EC USB connector with a USB charger (5 V)
USB charger or PC
5V
No
debug
5V
DT59067V1
3V3
UM3115 - Rev 2
page 16/44
UM3115
External power supply input from the USB user connector (5 V, 3 A maximum)
8.5
External power supply input from the USB user connector (5 V, 3 A maximum)
The STM32H5 Nucleo-144 board and shield can be powered from the USB user connector (CN13). To select the
USB user power source, JP2 must be fitted on [9-10] 'USB USER' (refer to Figure 12 and Table 10).
Table 10. External power source USB user (5 V, 3 A)
Input power
name
Connector pins
Voltage
Maximum current
USB USER
CN13
5V
3A
Figure 12. Power supply input from USB user connector (5 V, 3 A)
3V3
5V
Host PC
UM3115 - Rev 2
DT59088V1
5V
page 17/44
UM3115
External power supply input 3V3_EXT (3.3 V, 1.3 A maximum)
8.6
External power supply input 3V3_EXT (3.3 V, 1.3 A maximum)
In some cases, it might be interesting to use the 3V3 provided by a shield board (CN8 pin 7 or CN11 pin 16)
directly as the power input (refer to Figure 13 and Table 11). In this case, note that programming and debugging
features are unavailable as STLINK-V3EC is not powered.
Table 11. External power source 3V3_EXT (3.3 V, 1.3 A maximum)
Input power
name
Connector pins
CN8 pin 7
3V3
CN11 pin 16
Voltage range
Maximum current
3.0 to 3.6 V
1.3 A
Figure 13. Power supply input from 3V3_EXT (3.3 V)
No er
p
jum
3V3
DT59068V1
3V3_EXT
8.7
Debugging/programming when not using an external power supply
When powered by VIN (VIN 5 V) or 5V_EXT (E5V), it is still possible to use STLINK-V3EC for programming or
debugging only. In this case, it is mandatory to power the board first using VIN 5 V or E5V, then connect the USB
cable from CN1 to the PC. In this way, the enumeration succeeds, thanks to the external power source.
The following power-sequence procedure must be respected:
1.
Configure the jumper JP2 [5-6] for E5V or [3-4] for VIN 5V.
2.
Connect the external power source to VIN 5 V or E5V.
3.
Power on the external power supply 7 V < VIN < 12 V to VIN 5 V, or 5 V for E5V.
4.
Check that the green LED (LD5) is turned ON.
5.
Connect the PC to the USB connector (CN1).
If this order is not respected, the following risks might be encountered:
1.
If the board needs more than 300 mA current, the PC might be damaged, or the PC can limit the supplied
current. As a consequence, the board is not powered correctly.
2.
If 300 mA is requested during enumeration, there is a risk that the request is rejected and the enumeration
does not succeed if the PC cannot provide such current. Consequently, the board is not power supplied. The
green LED (LD5) remains OFF.
UM3115 - Rev 2
page 18/44
UM3115
Clock sources
9
Clock sources
9.1
HSE clock (high‑speed external clock)
There are four ways to configure the pins corresponding to the high‑speed external clock (HSE):
•
•
•
•
MCO from STLINK-V3EC (default): The MCO output of ST-LINK is used as an input clock of the STM32H5.
The MCO clock frequency cannot be changed. It is fixed at 8 MHz and connected to the PF0/PH0‑OSC_IN
of the STM32H5 series microcontroller. The configuration must be:
–
SB49 ON
–
SB48 and SB50 OFF
–
SB3 and SB4 OFF
HSE on-board oscillator from X3 crystal (provided): For typical frequencies and its capacitors and resistors,
refer to the STM32H5 series microcontroller datasheet and the application note Oscillator design guide for
STM8AF/AL/S, STM32 MCUs and MPUs (AN2867) for the oscillator design guide. The X3 crystal has the
following characteristics: 25 MHz, 6 pF, and 20 ppm. ST recommends using NX2016SA-25MHz-EXS00ACS11321 manufactured by NDK. The configuration must be:
–
SB3 and SB4 ON
–
C69 and C70 ON with 5.6 pF capacitors
–
SB48 and SB50 OFF
–
SB49 OFF
Oscillator from external PF0/PH0: From an external oscillator through pin 29 of the CN11 connector. The
configuration must be:
–
SB50 ON
–
SB48 and SB49 OFF
–
SB3 and SB4 OFF
HSE not used: PF0/PH0 and PF1/PH1 are used as GPIOs instead of clocks. The configuration must be:
–
–
–
9.2
SB48 and SB50 ON
SB49 OFF
SB3 and SB4 OFF
LSE clock (low‑speed external clock): 32.768 kHz
There are three ways to configure the pins corresponding to the low-speed clock (LSE):
•
•
•
On-board oscillator (default): X2 crystal. Refer to the application note Oscillator design guide for
STM8AF/AL/S, STM32 MCUs and MPUs (AN2867) for oscillator design guide for STM32H5 series
microcontrollers. ST recommends using NX3215SA-32.768kHZ-EXS00A-MU00525 (32.768 kHz, 9 pf load
capacitance, 20 ppm) from NDK. The configuration must be:
–
SB44 and SB45 OFF
–
R34 and R35 ON
Oscillator from external PC14: From an external oscillator through pin 25 of the CN11 connector. The
configuration must be:
–
SB45 ON
–
SB44 OFF
–
R34 and R35 OFF
LSE not used: PC14 and PC15 are used as GPIOs instead of the low-speed clock.
The configuration must be:
–
–
UM3115 - Rev 2
SB44 and SB45 ON
R34 and R35 OFF
page 19/44
UM3115
Board functions
10
Board functions
10.1
LEDs
User green LED (LD1)
The user green LED (LD1) is connected to the PB0 STM32 I/O (SB43 ON and SB51 OFF) or PA5 (SB51 ON and
SB43 OFF) corresponding to the D13 ST Zio.
User yellow LED (LD2)
The user yellow LED (LD2) is connected to PF4.
User red LED (LD3)
The user red LED (LD3) is connected to PG4.
These user LEDs are ON when the I/O is in the HIGH state, and are OFF when the I/O is in the LOW state.
COM LED (LD4)
The tri-color (green, orange, and red) LED (LD4) provides information about the ST-LINK communication status.
LD4 default color is red. LD4 turns to green to indicate that communication is in progress between the PC and
STLINK-V3EC, with the following setup:
•
•
•
•
•
•
•
Slow blinking red/OFF at power-on before USB initialization
Fast blinking red/OFF after the first correct communication between PC and STLINK-V3EC (enumeration)
Red LED ON when the initialization between the PC and STLINK-V3EC is complete
Green LED ON after a successful target communication initialization
Blinking red/green during communication with the target
Green ON communication finished and successful
Orange ON communication failure
Green PWR LED (LD5)
The green LED (LD5) indicates that the +5 V power supply is available on the STM32H5 Nucleo-144. This source
is available on CN8 pin 9 and CN11 pin 18.
STLINK POWER STATUS LD6
The tricolor LED (LD6) provides information about the STLINK-V3EC target power.
USB Type-C® green LED (LD7)
The green LED (LD7) indicates the VBUS presence on the user USB Type-C® connector (CN13).
10.2
Push-buttons
Blue user button (B1)
The user button is connected to the PC13 I/O by default (tamper support: SB54 ON and SB59 OFF) or PA0
(wake‑up support: SB59 ON and SB54 OFF) of the STM32H5 series microcontroller
Black reset button (B2)
This push-button is connected to NRST and is used to reset the STM32H5 series microcontroller.
UM3115 - Rev 2
page 20/44
UM3115
MCU voltage selection 1V8/3V3
10.3
MCU voltage selection 1V8/3V3
The STM32H5 Nucleo-144 board offers the possibility to supply the STM32H5 microcontroller with 1.8 or 3.3 V.
JP4 is used to select the VDD_MCU power level:
•
•
10.4
JP4 jumper must be fitted on [1-2] to supply the MCU with 3V3
JP4 jumper must be fitted on [2-3] to supply the MCU with 1V8
Current consumption measurement (IDD)
The JP5 jumper, labeled IDD, is used to measure the STM32H5 microcontroller consumption by removing the
jumper and by connecting an ammeter:
•
•
10.5
JP5 must be ON when STM32H5 is powered with VDD (default)
If JP5 is OFF, an ammeter must be connected to measure the STM32H5 current. If there is no ammeter,
the STM32H5 is not powered.
Virtual COM port (VCP): LPUART1/USART3
The STM32H5 Nucleo-144 board offers the flexibility to connect the LPUART1 or the USART3 interface to the
STLINK-V3EC, or to the ST morpho and ARDUINO® Uno V3 connectors.
The selection is done by setting the related solder bridges (refer to Table 12 and Table 13 below).
By default, the serial interface USART3 (PD8/PD9) that supports the bootloader is connected and directly
available as a Virtual COM port of a PC connected to the STLINK-V3EC USB Type-C® connector (CN1).
Table 12. USART3 connection
Pin
name
Definition
PD8
USART3 TX
PD9
USART3 RX
Virtual COM port (default configuration)
ST morpho connection
SB24 ON
SB13 ON
SB13, SB15, and SB23 OFF
SB23 and SB24 OFF
SB18 ON
SB75 ON
SB40, SB65, and SB75 OFF
SB18 and SB65 OFF
Table 13. LPUART1 connection
Pin
name
Definition
PB6
LPUART1 TX
PB7
LPUART1 RX
Virtual COM port (default
configuration)
ARDUINO® D0 and D1
SB15 and SB23 ON
SB14 and SB24 ON
SB14, SB24 OFF
SB15 and SB23 OFF
SB40 and SB65ON
SB18 and SB63 ON
SB18 and SB63 OFF
SB40 and SB65 OFF
ST morpho connection
SB14 and SB15 OFF
SB40 and SB63 OFF
By default:
UM3115 - Rev 2
•
Serial communication between the target MCU and ST-LINK MCU is enabled on USART3 because this
interface supports the Bootloader mode.
•
Serial communication between the target MCU, ARDUINO® Uno V3, and ST morpho connectors is
enabled on LPUART1, not to interfere with the VCP interface.
page 21/44
UM3115
USB Type-C® FS
10.6
USB Type-C® FS
The STM32H5 Nucleo-144 board supports USB full-speed (FS) communication. The USB connector (CN13) is a
USB Type-C® connector.
The STM32H5 Nucleo-144 board supports the USB Type-C® Sink mode only.
A green LED (LD7) lights up when VBUS is powered by a USB Host and the NUCLEO-H563ZI board works as a
USB Device.
10.6.1
USB FS device
When a USB Host connection to the USB Type-C® connector (CN13) of the STM32H5 Nucleo-144 board is
detected, the board starts behaving as a USB Device.
Depending on the powering capability of the USB Host, the board can take power from the VBUS terminal of
CN13. In the board schematic diagrams, the corresponding power voltage line is called 5V_UCPD. The STM32H5
Nucleo-144 board supports a 5 V USB voltage, from 4.75 to 5.25 V. On the MCU side, VDD_USB supports the
3V3 voltage only. Section 8 provides information on how to use powering options. The hardware configuration for
the USB FS interface is shown in Table 14.
Table 14. Hardware configuration for the USB interface
Pin
name
Function
Solder bridge
State(1)
Description
PA11 can be used as a GPIO on the ST morpho connector (CN12).
PA11
USB_FS_N
SB21
ON
USB function can be used also but performance is degraded due to
track length and impedance mismatch.
OFF
PA11 used as USB_FS_N signal
PA12 can be used as a GPIO on the ST morpho connector (CN12).
PA12
USB_FS_P
SB22
ON
USB function can be used also but performance might be degraded
due to track length and impedance mismatch.
OFF
PA12 used as USB_FS_P signal
1. The default configuration is in bold.
10.6.2
UCPD
The USB Type-C® introduces the USB power-delivery feature. The STM32H5 Nucleo-144 supports the dead
battery and the Sink mode.
In addition to the DP/DM I/O directly connected to the USB Type-C® connector, five I/Os are also used for UCPD
configuration: Configuration channel (UCPD_CC1 and UCPD_CC2), VBUS-SENSE, UCPD dead battery
(UCPD_DBn), and UCPD_FLT (FAULT) feature.
To protect the STM32H5 Nucleo-144 from USB overvoltage, a Programmable Power Supply (PPS) compliant
USB Type-C® port protection is used: TCPP01‑M12 IEC6100‑4‑2 level 4‑compliant IC:
•
•
•
UM3115 - Rev 2
Configuration Channel I/O: UCPD_CCx: These signals are connected to the associated CCx line of the
USB Type-C® connector through the STM USB port protection TCPP01-M12. These lines are used for the
configuration channel lines (CCx) to select the USB Type-C® current mode. The STM32H5 Nucleo-144
supports only Sink current mode.
Dead battery I/O: UCPD_DBn: This signal is connected to the associated DBn line of the TCPP01-M12.
The STM USB port protection TCPP01-M12 internally manages the dead battery resistors.
VBUS fault detection: UCPD_FLT: This signal is provided by the ST USB Type-C® port protection. It is used
as a fault reporting to the MCU after a bad VBUS level detection. By design, the STM32H5 Nucleo-144
VBUS protection is set to 6 V maximum. (R56 is set to 2.4 kΩ to select 6 V maximum).
page 22/44
UM3115
Ethernet
Table 15. Hardware configuration for the UCPD feature
Pin
name
Function
Solder
Bridge
State(1)
Description
ON
PB13 is connected to the USB Type-C® port protection and used as
UCPD_CC1. (SB6 and SB12 must be OFF).
If SB6 is ON, thus the protection on the CC1 line is bypassed
PB13
UCPD_CC1
PB13 can be used as:
SB29
•
GPIO on ST morpho connector (CN12)
•
–
(SB12 must be OFF)
I2S_CK signal on the Zio connector (CN7)
OFF
–
PB14
PG7
PA9
PA4
UCPD_CC2
UCPD_FLT
UCPD_DBn
VBUS_SENSE
SB30
SB74
SB31
SB56
(SB12 must be ON).
PB14 is connected to the USB Type-C® port protection and used as
UCPD_CC2. (SB5 must be OFF).
ON
If SB5 is ON, the protection on the CC2 line is bypassed
OFF
PB13 can be used as a GPIO on the ST morpho connector (CN12)
ON
PG7 is connected to the USB Type-C® port protection and used as
overvoltage fault reporting to the MCU.
OFF
PB13 can be used as a GPIO on the ST morpho connector (CN12)
ON
PA9 is connected to the USB Type-C® port protection and is used
as a dead battery feature
OFF
PA9 can be used as a GPIO on the ST morpho connector (CN12)
ON
PA4 is used as the VBUS_SENSE signal
OFF
PA4 can be used as a GPIO on the ST morpho connector (CN11)
1. The default configuration is in bold.
10.7
Ethernet
The STM32H5 Nucleo-144 board supports 10M/100M Ethernet communication by a PHY LAN8742A-CZ-TR
(U15) and RJ45 connector (CN14). Ethernet PHY is connected to the STM32H5 series microcontroller via the
RMII interface. The PHY RMII_REF_CLK generates the 50 MHz clock for the STM32H5 series microcontroller.
Note:
Make sure that JP6 is ON when using Ethernet.
Note:
Ethernet PHY LAN8742A must be set in power-down mode (in this mode, the Ethernet PHY reference clock
turns off) to achieve the expected low-power mode current. This is done by configuring the Ethernet PHY basic
control register (at address 0x00) bit 11 (power down) to '1'. SB58 can also be OFF to get the same effect.
Table 16. Ethernet pin configuration
UM3115 - Rev 2
Pin name
Function
Conflict with Zio
connector signal
Configuration when
using Ethernet
Configuration when
using ST Zio or ST
morpho connector
PA1
RMII reference clock
-
SB58 ON
SB58 OFF
PA2
RMII MDIO
-
SB69 ON
SB69 OFF
PC1
RMII MDC
-
SB62 ON
SB62 OFF
PA7
RMII RX data valid
-
SB38 ON
SB38 OFF
PC4
RMII RXD0
-
SB42 ON
SB42 OFF
PC5
RMII RXD1
-
SB36 ON
SB36 OFF
PG11
RMII TX enable
-
SB34 ON
SB34 OFF
PG13
RXII TXD0
-
SB37 ON
SB37 OFF
PB15
RMII TXD1
I2S_A_SD
JP6 ON
JP6 OFF
page 23/44
UM3115
Solder bridges and jumpers
11
Solder bridges and jumpers
SBxx can be found on the top layer and SB1xx can be found on the bottom layer of the STM32H5 Nucleo-144
board.
Table 17. Solder bridge and jumper configuration
Solder Bridge
SB1 (3V3)
SB2 (1V8)
State(1)
Description
ON
Output of voltage regulator ST1L05CPU33R is connected to 3V3.
OFF
Output of voltage regulator ST1L05CPU33R is not connected to 3V3.
ON
Output of voltage regulator ST1L05BPUR is connected to 1V8.
OFF
Output of voltage regulator ST1L05BPUR is not connected to 1V8.
SB3, SB4
ON, ON
PH0/PF0 and PH1/PF1 are connected to the external 25 MHz crystal X3.
(External 25 MHz
crystal)
OFF,
OFF
PH0/PF0 and PH1/PF1 are not connected to the external 25 MHz crystal X3.
SB5, SB6
ON, ON
The overvoltage protections on CC1 and CC2 lines are bypassed.
(OVP protections on
CC lines)
OFF,
OFF
The overvoltage protections on CC1 and CC2 lines are connected.
SB7
ON
The overvoltage protection on the VBUS line is bypassed.
(OVP protection on
VBUS line)
OFF
The overvoltage protection on the VBUS line is connected.
SB8, SB9, SB64,
SB68, SB78
(trace signals)
SB10 (PB15)
SB11
SB12 (PB13)
SB13 (PD8)
SB14, SB63,
SB15, SB40
(PB6, PB7)
ON, ON,
ON, ON,
ON
PE2, PE3, PE4, PE5, and PE6 are used as GPIOs on the ST morpho connector (CN11) or
on the Zio connector (CN9).
OFF,
OFF,
OFF,
OFF,
OFF
PE2, PE3, PE4, PE5, and PE6 are used as trace signals and are connected to the MIPI-20
connector (CN5). SB70 and SB71 must be OFF.
ON
PB15 can be used as I2S_2_SD or a GPIO signal on the Zio connector (pin 3 of CN7) if not
used on the ST morpho.
OFF
PB15 is used as RMII_TXD1 signal.
ON
The input of the ST1L05BPUR LDO is connected to 3V3.
OFF
The input of the ST1L05BPUR LDO is not connected to 3V3.
ON
PB13 can be used as I2S_2_CK or GPIO signal on the Zio connector (CN7/pin5) if not
used on the ST morpho.
OFF
PB13 is used as the UCPD_CC1 signal.
ON
PD8 is connected to the ST morpho (CN12/pin12).
OFF
PD8 is not connected to the ST morpho (CN12/pin12).
ON, ON,
OFF,
OFF
OFF,
OFF
LPUART1 is connected to ARDUINO® D0 and D1 (default).
LPUART1 connected to Virtual COM port (VCP).
ON, ON
SB16, SB25
SB17 (PB5)
UM3115 - Rev 2
ON, OFF IOREF is connected to VDD (default).
OFF, ON IOREF is connected to 3V3.
ON
PB5 (SPI1_MOSI/I2S_3_MCK) is connected to the ST Zio connector (pin13 of CN7).
OFF
PB5 (SPI1_MOSI/I2S_3_MCK) is not connected to the ST Zio connector (pin13 of CN7).
page 24/44
UM3115
Solder bridges and jumpers
Solder Bridge
State(1)
Description
ON, ON,
SB18, SB24,
SB23, SB65
(USART3)
OFF,
OFF
OFF,
OFF,
USART3 is connected to the Virtual COM Port (VCP) (default).
USART3 is connected to ARDUINO® D0 and D1.
ON, ON
ON
SDMMC data (D0/D1) signals are connected to the ST morpho connector (CN12).
OFF
SDMMC data signals (D0/D1) are not connected to the ST morpho connector (CN12) to
avoid stubs on SDMMC data signals.
ON, ON
These pins can be used as GPIOs on the ST morpho connector (CN12). (SB27 and SB28
must be OFF).
SB22 (PA12)
OFF,
OFF
These pins are used as D- and D+ on the USB connector (CN13). (SB27 and SB28 must
be ON). (Default).
SB26
(VDD33_USB_2)
ON
VDD33_USB_2 pin of STM32H5 is connected to 3V3.
OFF
VDD33_USB_2 pin of STM32H5 is not connected.
SB19 (SDMMC_D0)
SB20 (SDMMC_D1)
SB21 (PA11)
ON, ON
SB29 (PB13)
SB30 (PB14)
SB31 (PA9)
SB32
(VDD_MMC_1)
SB33, SB39 (PB3)
RMII signals
SB34 (PG11), SB36
(PC5), SB37 (PG13),
SB38 (PA7), SB42
(PC4), SB58 (PA1),
SB62 (PC1), SB69
(PA2), JP6 (PB15)
OFF,
OFF
PB13 and PB14 are used as the UCPD_CC1 and UCPD_CC2 signals.
(SB12 must be OFF)
PB13 and PB14 can be used as GPIOs on the ST morpho connector (CN12). (SB12 must
be OFF).
PB13 can be used as the I2S_2_CK signal on the ST Zio connector (CN7) (SB12 must be
ON).
ON
PA9 is connected and used as the UCPD_DBn signal (dead battery detection).
OFF
PA9 can be used as GPIO on the ST morpho connector (CN12).
ON
VDD_MMC_1 pin of STM32H5 is connected to VDD_MCU.
OFF
VDD_MMC_1 pin of STM32H5 is not connected.
OFF, ON
SWO signal of the STM32H5 (PB3) is connected to the ST-LINK SWO input (SB33 must be
OFF).
ON, OFF
PB3 is connected on ST Zio connector (CN7) and can be used as I2S_3_CK/ SPI1_SCK
signals.
OFF,
OFF
PB3 can be used as GPIOs on the ST morpho connector (CN12).
ON
These pins are used as RMII signals and connected to Ethernet PHY. SB10 must be OFF.
PB15 can be used as I2S_2_SD on ST Zio (pin 3 of CN7) if not used on the ST morpho.
OFF
These pins can be used as GPIOs on the ST morpho connectors. PB15 can be used as
I2S_2_SD on ST Zio (pin 3 of CN7) if not used on the ST morpho.
ON, OFF PE9 is used as TIM1_CH1 on the ST Zio connector (CN9)
SB35, SB67 (PE9)
OFF, ON
PE9 is used as GPIO on the ST Zio connector (CN9) and the ST morpho connector
(CN12).
ON, OFF The green user LED (LD1) is connected to PB0. (default).
SB43, SB51
(LD1 green LED)
SB44, SB45
(32.768 kHz crystal)
UM3115 - Rev 2
OFF, ON The green user LED (LD1) is connected to D13 of the ARDUINO® signal (PA5).
OFF,
OFF
The green user LED (LD1) is not connected.
ON, ON
PC14 and PC15 are connected to the ST morpho connector (CN11). R34 and R35 must be
OFF.
page 25/44
UM3115
Solder bridges and jumpers
Solder Bridge
State(1)
SB44, SB45
OFF,
OFF
(32.768 kHz crystal)
Description
X2 Crystal provides the 32.768KHz clock. PC14 and PC15 are not connected to the ST
morpho connector (CN11).
OFF, ON, The MCO clock (8 MHz) from ST-LINK is used as the main clock of the STM32H563ZIT6
OFF
MCU and is connected to its PH0-OSCIN pin. (Default). SB3 and SB4 must be OFF.
SB48, SB49, SB50
(HSE clock)
ON, OFF, PF0/PH0 and PF1/PH1 are connected to the ST morpho connector (CN11). SB3 and SB4
ON
must be OFF.
OFF,
OFF,
OFF
PF0/PH0 and PF1/PH1 are connected to the external 25 MHz crystal X3. SB3 and SB4
must be ON.
ON, ON
The I2C1 bus is connected to the ST Zio connector (pin9 and pin11 of CN9). SB53 and
SB60 must be OFF.
SB52, SB57
(I²C)
OFF,
OFF
The I2C1 bus is not connected to the ST Zio connector (pin9 and pin11 of CN9).
ADC_IN are connected to A4 and A5 (pin 9 and pin 11) on the ST Zio connector (CN9).
Thus, SB53 and SB60 must be ON.
ON, OFF The B1 push-button is connected to PC13.
SB54, SB59
OFF, ON The B1 push-button is connected to PA0 (set SB73 OFF if the ST Zio connector is used).
(B1 user button)
OFF,
OFF
The B1 push-button is not connected.
SB55
ON
The VBAT pin of the STM32H5 is connected to VDD_MCU.
(VBAT)
OFF
The VBAT pin of the STM32H5 is not connected to VDD_MCU.
ON
PA4 is connected to the VBUS_SENSE signal.
OFF
PA4 is not connected to the VBUS_SENSE signal and can be used as GPIO on the ST
morpho connector (CN11).
SB56
(VBUS_SENSE)
ON, OFF PB2 is used as QSPI_CK signal on the ST Zio connector (pin15 of CN10).
SB61, SB66 (PB2)
OFF, ON PB2 can be used as GPIO on the ST Zio connector (pin13 of CN9).
OFF,
OFF
PB2 can be used as GPIO on the ST morpho connector (CN12)
ON
PE2 is connected to the ST Zio connector (pin25 of CN10) and is used as the
QSPI_BK1_IO2 signal.
OFF
PE2 can be used as the trace signal if SB64 is OFF or as the SAI_A_MCLK signal on ST
Zio connector (pin14 of CN9) if SB64 is ON.
ON
PE6 is connected to the ST Zio connector (pin28 of CN10) and is used as the
TIMER_1_BKIN1 signal. SB68 must be OFF.
OFF
PE2 can be used as the trace signal if SB68 is OFF or as the SAI_A_SD signal on ST Zio
connector (pin20 of CN9) if SB68 is ON.
ON
NRST of STM32H5 is connected to Ethernet PHY (U15).
OFF
NRST of STM32H5 is not connected to Ethernet PHY (U15).
ON
PA0 is connected to the ST Zio connector (pin 29 of CN10).
OFF
PA0 is not connected to the ST Zio connector (pin 29 of CN10).
ON
PG7 is used as the UCPD_FLT signal.
OFF
PG7 can be used as GPIO on the ST morpho connector (CN12).
ON
PD9 is connected to the ST morpho connector (CN11).
OFF
PD9 is not connected to the ST morpho connector (CN11).
SB84
ON
The pin11 and pin15 (TrgtPwr pins) of trace connector CN5 are connected to GND.
(TargetPwr)
OFF
The pin11 and pin15 (TrgtPwr pins) of trace connector CN5 are not connected to GND.
SB70 (PE2)
SB71 (PE6)
SB72
(Ethernet nRST)
RMII signal
SB73 (PA0)
SB74 (PG7)
SB75 (PD9)
UM3115 - Rev 2
page 26/44
UM3115
Solder bridges and jumpers
Solder Bridge
State(1)
JP1
ON
Description
An external debugger connected to the MIPI20 connector (CN5) can be used. The level
shifter (U1) is in high impedance (high‑Z).
STLINK-V3EC no longer drives the embedded STM32.
(external debug)
OFF
The embedded STLINK-V3EC is selected (default configuration).
JP3
ON
STLINK-V3EC is in the Reset mode.
(ST-LINK RST)
OFF
STLINK-V3EC is active.
JP5
ON
VDD_MCU is connected to VDD.
(IDD)
OFF
VDD_MCU is not connected to VDD (the MCU is not power supplied).
1. The default status is in bold.
All the other solder bridges present on the STM32H5 Nucleo-144 board are used to configure several I/Os and
power supply pins for compatibility of features and pinout with the target‑supported STM32H5.
The STM32H5 Nucleo-144 board is delivered with the solder bridges configured according to the target STM32H5
supported.
UM3115 - Rev 2
page 27/44
UM3115
Board connectors
12
Board connectors
Several connectors are implemented on the STM32H5 Nucleo-144 board.
12.1
STLINK-V3EC USB Type-C® connector (CN1)
The USB Type-C® connector (CN1) is used to connect the embedded STLINK-V3EC to the PC for programming
and debugging purposes.
Figure 14. USB Type-C® connector (CN1) front view
The related pinout for the USB STLINK-V3EC connector is listed in Table 18.
Table 18. STLINK-V3EC USB Type-C® connector (CN1) pinout
Connector
CN1
UM3115 - Rev 2
Pin number
Pin name
Signal name
STM32H5
pin
A1
GND
GND
-
Ground
A4
VBUS
VBUS_STLK
-
Power
A5
CC1
STLK_UCPD_CC1_C
PC3
USB-PD controller side for the CC1 pin
A6
D+
STLK_USB_P
PB15
USB differential pair P
A7
D-
STLK_USB_N
PB14
USB differential pair M
A8
SBU1
-
-
-
A9
VBUS
VBUS_STLK
-
Power
A12
GND
GND
-
Ground
B1
GND
GND
-
Ground
B4
VBUS
VBUS_STLK
-
Power
B5
CC2
STLK_UCPD_CC2_C
PC4
USB-PD controller side for the CC2 pin
B6
D+
STLK_USB_P
PB15
USB differential pair P
B7
D-
STLK_USB_N
PB14
USB differential pair M
B9
VBUS
VBUS_STLK
-
Power
B12
GND
GND
-
Ground
Function
page 28/44
UM3115
User USB Type-C® connector (CN13)
12.2
User USB Type-C® connector (CN13)
Figure 15. USB Type-C® connector (CN13) front view
The related pinout for the user USB connector is listed in Table 19.
Table 19. User USB Type-C® connector (CN13) pinout
Connector
CN13
12.3
Pin number
Pin name
Signal name
STM32H5
pin
A1
GND
GND
-
Ground
A4
VBUS
VBUSc
-
Power
A5
CC1
UCPD_CC1
PB13
USB-PD controller side for the CC1 pin
A6
D+
USB_FS_P
PA12
USB differential pair P
A7
D-
USB_FS_N
PB11
USB differential pair M
A8
SBU1
-
-
-
A9
VBUS
VBUSc
-
Power
A12
GND
GND
-
Ground
B1
GND
GND
-
Ground
B4
VBUS
VBUSc
-
Power
B5
CC2
UCPD_CC2
PB14
USB-PD controller side for the CC2 pin
B6
D+
USB_FS_P
PA12
USB differential pair P
B7
D-
USB_FS_N
PA11
USB differential pair M
B9
VBUS
VBUSc
-
Power
B12
GND
GND
-
Ground
Function
Ethernet RJ45 connector (CN14)
The STM32H5 Nucleo-144 board supports 10 Mbps/100 Mbps Ethernet communication with the LAN8742A-CZTR PHY (U15) from MICROCHIP and integrated RJ45 connector (CN14). The Ethernet PHY is connected to the
MCU via the RMII interface.
UM3115 - Rev 2
page 29/44
UM3115
Ethernet RJ45 connector (CN14)
The X4 oscillator generates the 25 MHz clock for the PHY. The 50 MHz clock for the MCU (derived from the
25 MHz crystal oscillator) is provided by the RMII_REF_CLK of the PHY.
Figure 16. Ethernet RJ45 connector (CN14) front view
1.
Green LED: Ethernet traffic
2.
Amber LED: Ethernet connection
The related pinout for the Ethernet connector is listed in Table 20. Ethernet connector (CN14) pinout.
Table 20. Ethernet connector (CN14) pinout
Connector
CN14
UM3115 - Rev 2
Pin number
Description
MCU pin
Pin number
Description
MCU pin
1
TX+
-
7
NC
-
2
TX-
-
8
NC
-
3
RX+
-
9
Yellow LED cathode
-
4
NC
-
10
Yellow LED anode
-
5
NC
-
11
Green LED cathode
-
6
RX-
-
12
Green LED anode
-
page 30/44
UM3115
Expansion connectors
13
Expansion connectors
13.1
ST Zio connectors
For all STM32H5 Nucleo-144 boards, Figure 17 shows the signals connected by default to the ST Zio connectors
(CN7, CN8, CN9, and CN10), including the support of ARDUINO® Uno V3.
Figure 17. STM32H5 Nucleo-144 board
CN7, CN8, CN9, and CN10 are female connectors on the top side and male connectors on the bottom side. They
include support for ARDUINO® Uno V3. Most shields designed for ARDUINO® can fit the STM32H5 Nucleo-144
board.
UM3115 - Rev 2
page 31/44
UM3115
ST Zio connectors
To cope with ARDUINO® Uno V3, apply the following modifications:
•
SB52 and SB57 must be ON
•
SB53 and SB60 must be OFF to connect I2C on A4 (pin 9) and A5 (pin 11 of CN9).
Caution:
The I/Os of the STM32H5 series microcontroller are 3.3 V compatible instead of 5 V for ARDUINO® Uno V3.
Caution:
R33 must be OFF before implementing the ARDUINO® shield with VREF+ power provided on CN7 pin 6.
NUCLEO-H563ZI pin assignments
Table 21. Zio connector (CN7) pinout
Zio
pin
Pin
name
Signal name
STM32
pin
STM32
function
Zio
pin
Pin
name
Signal name
STM32
pin
STM32
function
1
D16
I2S_A_MCK
PC6
I2S_2
2
D15
I2C_A_SCL
PB8
I2C1_SCL
3
D17
I2S_A_SD
PB15
I2S_2
4
D14
I2C_A_SDA
PB9
I2C1_SDA
5
D18
I2S_A_CK
PB13
I2S_2
6
VREFP
VREFP
-
VDDA/
VREFP
7
D19
I2S_A_WS
PB12
I2S_2
8
GND
GND
-
-
9
D20
I2S_B_WS
PA15
I2S_3
10
D13
SPI_A_SCK
PA5
SPI1_SCK
11
D21
I2S_B_MCK
PC7
I2S_3
12
D12
SPI_A_MISO
PG9
SPI1_MISO
13
D22
I2S_B_SD/
SPI_B_MOSI
PB5
I2S_3/SPI1
14
D11
SPI_A_MOSI/
TIM_E_PWM1
PB5
SPI1_MOSI/
TIM3_CH2
15
D23
I2S_B_CK/
SPI_B_SCK
PB3
I2S_3/SPI1
16
D10
SPI_A_CS/
TIM_B_PWM3
PD14
SPI1_CS/
TIM4_CH3
17
D24
SPI_B_NSS
PG10
SPI1
18
D9
TIM_B_PWM2
PD15
TIM4_CH4
19
D25
SPI_B_MISO
PB4
SPI1
20
D8
IO
PF3
-
1.
2.
For more details, refer to Table 17. Solder bridge and jumper configuration.
PB13 is used as I2S_A_CK and connected to CN7 pin 5. If JP6 is ON, it is also connected to Ethernet PHY
as RMII_TXD1. In this case, only one function of the Ethernet or I2S_A must be used.
Table 22. Zio connector (CN8) pinout
UM3115 - Rev 2
Zio
pin
Pin
name
Signal name
STM32
pin
STM32
function
Zio
pin
Pin
name
Signal name
STM32
pin
STM32
function
1
NC
NC
-
-
2
D43
SDMMC_D0
PC8
SDMMC1
3
IOREF
IOREF
-
3.3 V reference
4
D44
SDMMC_D1/
I2S_A_CKIN
PC9
SDMMC1/
I2S2_CKIN
5
NRST
NRST
NRST
Reset
6
D45
SDMMC_D2
PC10
SDMMC1
7
3V3
3V3
-
3.3 V input/
output
8
D46
SDMMC_D3
PC11
SDMMC1
9
5V
5V
-
5V output
10
D47
SDMMC_CK
PC12
SDMMC1
11
GND
GND
-
Ground
12
D48
SDMMC_CMD
PD2
SDMMC1
13
GND
GND
-
Ground
14
D49
IO
PG2
-
15
VIN
VIN
-
Power input
16
D50
IO
PG3
-
page 32/44
UM3115
ST Zio connectors
Table 23. Zio connector (CN9) pinout
Zio
pin
Pin
name
Signal name
STM32
pin
STM32
function
Zio
pin
Pin
name
Signal name
STM32
pin
STM32
function
1
A0
ADC
PA6
ADC12_INP3
2
D51
USART_B_SCLK
PD7
USART2
3
A1
ADC
PC0
ADC12_INP10
4
D52
USART_B_RX
PD6
USART2
5
A2
ADC
PC3
ADC12_INP13
6
D53
USART_B_TX
PD5
USART2
7
A3
ADC
PB1
ADC12_INP5
8
D54
USART_B_RTS
PD4
USART2
9
A4
ADC
PC2/
PB9
ADC12_INP12/
I2C1_SDA
10
D55
USART_B_CTS
PD3
USART2
11
A5
ADC
PF11/
PB8
ADC1_INP2/
I2C1_SCL
12
GND
GND
-
-
13
D72
IO
PB2
-
14
D56
SAI_A_MCLK
PE2
SAI1_A
15
D71
IO
PE9
-
16
D57
SAI_A_FS
PE4
SAI1_A
17
D70
I2C_B/SMBA
PF2
I2C2
18
D58
SAI_A_SCK
PE5
SAI1_A
19
D69
I2C_B_SCL
PF1
I2C2
20
D59
SAI_A_SD
PE6
SAI1_A
21
D68
I2C_B_SDA
PF0
I2C2
22
D60
SAI_B_SD
PE3
SAI1_B
23
GND
GND
-
-
24
D61
SAI_B_SCK
PF8
SAI1_B
25
D67
CAN_RX
PD0
CAN_1
26
D62
SAI_B_MCLK
PF7
SAI1_B
27
D66
CAN_TX
PD1
CAN_1
28
D63
SAI_B_FS
PF9
SAI1_B
29
D65
IO
PG0
-
30
D64
IO
PG1
-
Table 24. Zio connector (CN10) pinout
UM3115 - Rev 2
Zio
pin
Pin
name
Signal name
STM32
pin
STM32
function
Zio
pin
Pin
name
Signal name
STM32
pin
STM32
function
1
AVDD
AVDD
-
Analog VDD
2
D7
IO
PG12
IO
3
AGND
AGND
-
Analog GND
4
D6
TIMER_A_PWM1
PE9
TIM1_CH1
5
GND
GND
-
GND
6
D5
TIMER_A_PWM2
PE11
TIM1_CH2
7
A6
ADC_A_IN
PF12
ADC1_INP6
8
D4
IO
PE14
IO
9
A7
ADC_B_IN
PF13
ADC2_INP2
10
D3
TIMER_A_PWM3
PE13
TIM1_CH3
11
A8
ADC_C_IN
PF14
ADC2_INP6
12
D2
IO
PG14
IO
13
D26
QSPI_BCS
PG6
QSPI1_NCS
14
D1
USART_A_TX
PB6
LPUART1
15
D27
QSPI_CLK
PB2
QSPI1_CLK
16
D0
USART_A_RX
PB7
LPUART1
17
GND
GND
-
-
18
D42
TIMER_A_PWM1N
PE8
TIM1_CH1N
19
D28
QSPI_BK1_IO3
PD13
QSPI1_IO
20
D41
TIMER_A_ETR
PE7
TIM1_ETR
21
D29
QSPI_BK1_IO1
PD12
QSPI1_IO
22
GND
-
-
-
23
D30
QSPI_BK1_IO0
PD11
QSPI1_IO
24
D40
TIMER_A_PWM2N
PE10
TIM1_CH2N
25
D31
QSPI_BK1_IO2
PE2
QSPI1_IO
26
D39
TIMER_A_PWM3N
PE12
TIM1_CH3N
27
GND
GND
-
-
28
D38
TIMER_A_BKIN2
PE6
TIM1_BKIN2
29
D32
TIMER_C_PWM1
PA0
TIM2_CH1
30
D37
TIMER_A_BKIN1
PE15
TIM1_BKIN1
31
D33
TIMER_D_PWM1
PB0
TIM3_CH3
32
D36
TIMER_C_PWM2
PB10
TIM2_CH3
33
D34
TIMER_B_ETR
PE0
TIM4_ETR
34
D35
TIMER_C_PWM3
PA3
TIM2_CH4
page 33/44
UM3115
ST morpho connector
13.2
ST morpho connector
The ST morpho connector consists of male-pin header footprints CN11 and CN12 (not soldered by default). They
are used to connect the STM32H5 Nucleo-144 board to an extension board or a prototype/wrapping board placed
on the top of the ST morpho. All signals and power pins of the STM32H5 are available on the ST morpho
connector. An oscilloscope, logical analyzer, or voltmeter can also probe this connector.
Table 25 shows the pin assignments of each STM32H5 on the ST morpho connector.
Table 25. Pin assignment of the ST morpho connector
CN11 odd pins
UM3115 - Rev 2
CN11 even pins
CN12 odd pins
CN12 even pins
Pin
number
Pin name
Pin
number
Pin name
Pin
number
Pin name
Pin
number
Pin name
1
PC10
2
PC11
1
PC9
2
PC8
3
PC12
4
PD2
3
PB8
4
PC6
5
VDD
6
5V_EXT
5
PB9
6
PC5
7
BOOT0
8
GND
7
VREFP
8
5V_STLK
9
PF6
10
NC
9
GND
10
PD8
11
PF7
12
IOREF
11
PA5
12
PA12
13
PA13
14
NRST
13
PA6
14
PA11
15
PA14
16
3V3
15
PA7
16
PB12
17
PA15
18
5V
17
PB6
18
NC
19
GND
20
GND
19
PC7
20
GND
21
PB7
22
GND
21
PA9
22
PB2
23
PC13
24
VIN
23
PA8
24
PB1
25
PC14
26
NC
25
PB10
26
PB15
27
PC15
28
PA0
27
PB4
28
PB14
29
PH0
30
PA1
29
PB5
30
PB13
31
PH1
32
PA4
31
PB3
32
AGND
33
VBAT
34
PB0
33
PA10
34
PC4
35
PC2
36
PC1
35
PA2
36
PF5
37
PC3
38
PC0
37
PA3
38
PF4
39
PD4
40
PD3
39
GND
40
PE8
41
PD5
42
PG2
41
PD13
42
PF10
43
PD6
44
PG3
43
PD12
44
PE7
45
PD7
46
PE2
45
PD11
46
PD14
47
PE3
48
PE4
47
PE10
48
PD15
49
GND
50
PE5
49
PE12
50
PF14
51
PF1
52
PF2
51
PE14
52
PE9
53
PF0
54
PF8
53
PE15
54
GND
55
PD1
56
PF9
55
PE13
56
PE11
57
PD0
58
PG1
57
PF13
58
PF3
59
PG0
60
GND
59
PF12
60
PF15
61
NC
62
PE6
61
PG14
62
PF11
63
PG9
64
PG15
63
GND
64
PE0
65
PG12
66
PG10
65
PD10
66
PG8
page 34/44
UM3115
ST morpho connector
CN11 odd pins
CN12 odd pins
CN12 even pins
Pin
number
Pin name
Pin
number
Pin name
Pin
number
Pin name
Pin
number
Pin name
67
NC
68
PG13
67
PG7
68
PG5
69
PD9
70
PG11
69
PG4
70
PG6
1.
2.
3.
UM3115 - Rev 2
CN11 even pins
The default state of BOOT0 is 0. It can be set to 1 when a jumper is set [5-7] on CN11.
5V_STLK is the 5 V power coming from the STLINK-V3EC USB connector that rises before and it rises
before the +5 V rises on the board.
PA13 and PA14 are shared with SWD signals connected to STLINK-V3EC. ST does not recommend using
them as I/O pins.
page 35/44
UM3115
NUCLEO-H563ZI product information
14
NUCLEO-H563ZI product information
14.1
Product marking
The stickers located on the top or bottom side of all PCBs provide product information:
•
First sticker: product order code and product identification, generally placed on the main board featuring
the target device.
Example:
Product order code
Product identification
•
Second sticker: board reference with revision and serial number, available on each PCB.
Example:
MBxxxx-Variant-yzz
syywwxxxxx
On the first sticker, the first line provides the product order code, and the second line the product identification.
On the second sticker, the first line has the following format: “MBxxxx-Variant-yzz”, where “MBxxxx” is the board
reference, “Variant” (optional) identifies the mounting variant when several exist, “y” is the PCB revision, and “zz”
is the assembly revision, for example B01. The second line shows the board serial number used for traceability.
Parts marked as “ES” or “E” are not yet qualified and therefore not approved for use in production. ST is not
responsible for any consequences resulting from such use. In no event will ST be liable for the customer using
any of these engineering samples in production. ST’s Quality department must be contacted prior to any decision
to use these engineering samples to run a qualification activity.
“ES” or “E” marking examples of location:
•
•
On the targeted STM32 that is soldered on the board (for an illustration of STM32 marking, refer to the
STM32 datasheet Package information paragraph at the www.st.com website).
Next to the evaluation tool ordering part number that is stuck, or silk-screen printed on the board.
Some boards feature a specific STM32 device version, which allows the operation of any bundled commercial
stack/library available. This STM32 device shows a “U” marking option at the end of the standard part number
and is not available for sales.
To use the same commercial stack in their applications, the developers might need to purchase a part number
specific to this stack/library. The price of those part numbers includes the stack/library royalties.
UM3115 - Rev 2
page 36/44
UM3115
NUCLEO-H563ZI product history
14.2
NUCLEO-H563ZI product history
Table 26. Product history
Order
code
Product
identification
Product details
Product change description
Product limitations
MCU:
•
STM32H563ZIT6
silicon revision "Z"
MCU errata sheet:
NUH563ZI$MR1
•
STM32H562xx/563xx/
573xx device errata
(ES0565)
Initial revision
Limitations linked to MCU silicon
revision "Z"
Updated MCU silicon revision
No limitation
NUCLEO-H563ZI
Board:
•
MB1404‑H563ZI-C01
(main board)
MCU:
•
STM32H563ZIT6
silicon revision "X"
MCU errata sheet:
NUH563ZI$MR2
•
STM32H562xx/563xx/
573xx device errata
(ES0565)
Board:
•
14.3
MB1404‑H563ZI-C01
(main board)
Board revision history
Table 27. Board revision history
Board reference
MB1404
(main board)
UM3115 - Rev 2
Board variant and revision
H563ZI-C01
Board change description
Initial revision
Board limitations
No limitation
page 37/44
UM3115
Federal Communications Commission (FCC) and ISED Canada Compliance Statements
15
Federal Communications Commission (FCC) and ISED Canada
Compliance Statements
15.1
FCC Compliance Statement
Part 15.19
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Part 15.21
Any changes or modifications to this equipment not expressly approved by STMicroelectronics may cause
harmful interference and void the user's authority to operate this equipment.
Part 15.105
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception which can be determined by turning the equipment off and on,
the user is encouraged to try to correct interference by one or more of the following measures:
•
•
•
•
Note:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Use only shielded cables.
Responsible party (in the USA)
Terry Blanchard
Americas Region Legal | Group Vice President and Regional Legal Counsel, The Americas
STMicroelectronics, Inc.
750 Canyon Drive | Suite 300 | Coppell, Texas 75019
USA
Telephone: +1 972-466-7845
15.2
ISED Compliance Statement
ISED Canada ICES-003 Compliance Label: CAN ICES-3 (B) / NMB-3 (B).
Étiquette de conformité à la NMB-003 d'ISDE Canada: CAN ICES-3 (B) / NMB-3 (B).
UM3115 - Rev 2
page 38/44
UM3115
Revision history
Table 28. Document revision history
Date
Revision
24-Feb-2023
1
04-Aug-2023
2
Changes
Initial release.
Updated:
UM3115 - Rev 2
•
•
PA15 replaced by PA5 on SPI1_SCK MCU signal in Table 21
New product identification including MCU silicon revision in Table 26
page 39/44
UM3115
Contents
Contents
1
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
2
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1
3
Products and codification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Development environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.1
System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.2
Development toolchains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.3
Demonstration software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4
Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
5
Quick start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
5.1
6
Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Hardware layout and configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
6.1
STM32H5 Nucleo-144 board layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6.2
Mechanical drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
7
Embedded STLINK-V3EC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
8
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
9
10
8.1
Power supply input from STLINK-V3EC USB connector: 5V_STLK (default configuration) 14
8.2
External power supply input from VIN (7 to 12 V, 800 mA maximum) . . . . . . . . . . . . . . . . . . 15
8.3
External power supply input 5V_EXT (5 V, 1.3 A maximum) . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8.4
External power supply input from a USB charger (5 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
8.5
External power supply input from the USB user connector (5 V, 3 A maximum) . . . . . . . . . . 17
8.6
External power supply input 3V3_EXT (3.3 V, 1.3 A maximum) . . . . . . . . . . . . . . . . . . . . . . . 18
8.7
Debugging/programming when not using an external power supply . . . . . . . . . . . . . . . . . . . 18
Clock sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
9.1
HSE clock (high‑speed external clock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
9.2
LSE clock (low‑speed external clock): 32.768 kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Board functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
10.1
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
10.2
Push-buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
10.3
MCU voltage selection 1V8/3V3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
10.4
Current consumption measurement (IDD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
10.5
Virtual COM port (VCP): LPUART1/USART3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
10.6
USB Type-C® FS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
UM3115 - Rev 2
10.6.1
USB FS device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
10.6.2
UCPD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
page 40/44
UM3115
Contents
10.7
Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
11
Solder bridges and jumpers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
12
Board connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
13
14
15
12.1
STLINK-V3EC USB Type-C® connector (CN1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
12.2
User USB Type-C® connector (CN13) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
12.3
Ethernet RJ45 connector (CN14) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Expansion connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
13.1
ST Zio connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
13.2
ST morpho connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
NUCLEO-H563ZI product information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
14.1
Product marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
14.2
NUCLEO-H563ZI product history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
14.3
Board revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Federal Communications Commission (FCC) and ISED Canada Compliance
Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
15.1
FCC Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
15.2
ISED Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
List of tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
List of figures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
UM3115 - Rev 2
page 41/44
UM3115
List of tables
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
Table 16.
Table 17.
Ordering information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Codification explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
ON/OFF convention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Default jumper configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
JP1 configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
MIPI20 debug connector (CN5) pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
External power sources VIN (7 to 12 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Power supply input from 5V_EXT (5 V, 1.3 A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
External power source CHGR (5 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
External power source USB user (5 V, 3 A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
External power source 3V3_EXT (3.3 V, 1.3 A maximum) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
USART3 connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
LPUART1 connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Hardware configuration for the USB interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Hardware configuration for the UCPD feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Ethernet pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Solder bridge and jumper configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Table 18.
STLINK-V3EC USB Type-C® connector (CN1) pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 19.
Table 20.
Table 21.
Table 22.
Table 23.
Table 24.
Table 25.
Table 26.
Table 27.
Table 28.
User USB Type-C® connector (CN13) pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Ethernet connector (CN14) pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Zio connector (CN7) pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Zio connector (CN8) pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Zio connector (CN9) pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Zio connector (CN10) pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Pin assignment of the ST morpho connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Product history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Board revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
UM3115 - Rev 2
page 42/44
UM3115
List of figures
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
NUCLEO-H563ZI top view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
NUCLEO-H563ZI bottom view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Hardware block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
STM32H5 Nucleo-144 board top layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
STM32H5 Nucleo-144 board bottom layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
STM32H5 Nucleo-144 board mechanical drawing (in millimeters) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Connecting an external debug tool to program the on-board STM32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Power supply input from STLINK-V3EC USB connector with PC (5 V, 500 mA maximum) . . . . . . . . . . . . . . . 14
Power supply input from VIN (7 to 12 V, 800 mA maximum) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Power supply input from 5V_EXT (5 V, 1.3 A maximum) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Power supply input from STLINK-V3EC USB connector with a USB charger (5 V) . . . . . . . . . . . . . . . . . . . . . 16
Power supply input from USB user connector (5 V, 3 A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Power supply input from 3V3_EXT (3.3 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 14.
USB Type-C® connector (CN1) front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Figure 15.
Figure 16.
Figure 17.
USB Type-C® connector (CN13) front view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Ethernet RJ45 connector (CN14) front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
STM32H5 Nucleo-144 board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
UM3115 - Rev 2
page 43/44
UM3115
IMPORTANT NOTICE – READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST
products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST
products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgment.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of
purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. For additional information about ST trademarks, refer to www.st.com/trademarks. All other product or service names
are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2023 STMicroelectronics – All rights reserved
UM3115 - Rev 2
page 44/44
">