Black Box RM3010 A, RM3020 A, RM3030 A, RM3040 A, RM313-R2, RM314, RM315-R2, RM316, RM317-R2, RM326-R2, RM320, RM321, RM322-R2, RM323-R2, RM324-R2, RM325-R2, RM327, RM328-R2, RM329, PS186A, PS187A-R2, SP187A, RM460, RM462 User manual
Hirdetés
Hirdetés
© Copyright 2003. Black Box Corporation. All rights reserved.
1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax 724-746-0746
RM3010A RM315-R2 RM323-R2 RM329
RM3020A RM316 RM324-R2 RM339
RM3030A RM317-R2 RM325-R2 RM340
RM3040A RM320 RM326-R2 RM341
RM313-R2 RM321
RM314 RM322-R2
RM327
RM328-R2
RM342
RM450
RM451
RM452
RM453
RM454
RM455
RM456
JULY 2003
RM457
RM458
RM459
RM460
RM462
RM464
RM465
Comm Cabinets and Accessories
CUSTOMER
SUPPORT
INFORMATION
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
Web site: www.blackbox.com • E-mail: [email protected]
CONTENTS/TRADEMARKS USED IN THIS MANUAL
Contents
Chapter Page
1.Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1 Available Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.2 Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2.1 What’s Included with the RM3010A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2.2 What’s Included with the RM3020A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2.3 What’s Included with the RM3030A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2.4 What’s Included with the RM3040A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.3 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.4 Products that Work Together . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.Assembly Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1 Comm Cabinets (RM3010A, RM3020A, RM3030A, RM3040A) . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2 Plexi Doors (RM460, RM462) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.3 Short Steel Doors (RM453, RM458) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.4 Standard Steel Doors (RM464, RM465) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.5 Lock for Steel Doors (RM313-R2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.6 Shelves, Solid and Vented (RM314, RM315-R2, RM316, RM317-R2) . . . . . . . . . . . . . . . . . . 22
3.7 630-CFM Fans (RM320, RM321) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.8 Leg Levelers (RM322-R2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.9 Casters (RM323-R2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.10 Drawers (RM324-R2, RM325-R2) and 18" Sliding Shelf (RM326-R2) . . . . . . . . . . . . . . . . . 27
3.11 Cage Nuts (RM327) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.13 Pan-Head Screws (RM328-R2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.14 Multi-Bay Joining Kit (RM329) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
TRADEMARKS USED IN THIS MANUAL
BLACK BOX and the logo are registered trademarks of Black Box Corporation.
Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owners.
1
2
COMM CABINETS AND ACCESSORIES
1. Specifications
Product Code
RM3010A
RM3020A
RM3030A
RM3040A
RM313-R2
RM314, RM315-R2
RM316, RM317-R2
RM320
RM321
RM322-R2
RM323-R2
RM324-R2
RM325-R2
RM326-R2
RM327
RM328-R2, RM329
RM453
RM458
RM460, RM464
RM462, RM465
Table 1-1. Product codes and sizes.
Size
77"H x 19"W x 30"D (195.6 x 48.3 x 76.2 cm)
77"H x 19"W x 25"D (195.6 x 48.3 x 63.5 cm)
42"H x 19"W x 30"D (106.7 x 48.3 x 76.2 cm)
42"H x 19"W x 25"D (106.7 x 48.3 x 63.5 cm)
2"H x 1"W x 1"D (5.1 x 2.5 x 2.5 cm)
17.72"W x 24.5"D (45 x 62.2 cm)
17.72"W x 30.5"D (45 x 77.5 cm)
5"H x 18.9"W x 20.9"D (12.7 x 47.9 x 53 cm)
5"H x 18.9"W x 26.9"D (12.7 x 47.9 x 68.3 cm)
3"H x 2"W x 2"D (7.6 x 5.1 x 5.1 cm)
3.5" diameter (8.9 cm)
3.43"H x 15.6"W x 16"D (8.7 x 39.6 x 40.6 cm)
10.4"H x 15.6"W x 16"D (26.4 x 39.6 x 40.6 cm)
16.7"W x 18"D (42.4 x 45.7 cm)
0.5"H x 0.5"W x 0.5"D (1.3 x 1.3 x 1.3 cm)
1.1"H (2.8 cm)
69.88"H x 20.12"W (177.5 x 51.1 cm)
34.88"H x 20.12"W (88.6 x 51.1 cm)
78.63"H x 20.12"W (199.7 x 51.1 cm)
43.63"H x 20.12"W (110.8 x 51.1 cm)
CHAPTER 2: Introduction
2. Introduction
The Comm Cabinets (RM3010A, RM3020A, RM3030A, and RM3040A) provide a convenient way to organize your equipment. They feature an enclosed rack on which you can mount your equipment. Plexi and Steel
Doors and Solid and Vented Shelves (RM460 and RM462; RM453, RM458, RM464, and RM465; RM314,
RM315-R2, RM316, and RM317-R2) are available for each cabinet model. Leg Levelers or Casters (RM322-R2 or
RM323-R2) either balance your cabinet or make it mobile. A Shelf (RM326-R2) and Drawers (RM324-R2 and
RM325-R2) provide easy access to equipment in the Cabinet.
2.1 Available Models
Table 2-1 lists the Comm Cabinets and their accessories by product code and name.
Table 2-1. Available models.
Product Code
RM3010A
RM3020A
RM329
RM339
RM340
RM341
RM342
RM450
RM451
RM452
RM453
RM454
RM455
RM456
RM3030A
RM3040A
RM313-R2
RM314
RM315-R2
RM316
RM317-R2
RM320
RM321
RM322-R2
RM323-R2
RM324-R2
RM325-R2
RM326-R2
RM327
RM328-R2
Product Name
Comm Cabinet 7730 (83" x 33")
Comm Cabinet 7725 (83" x 27")
Comm Cabinet 4230 (48" x 33")
Comm Cabinet 4225 (48" x 27")
Lock—Steel Door Only
Shelf—25" Solid
Shelf—25" Vented
Shelf—30" Solid
Shelf—30" Vented
630-CFM Fan/Panel Assembly 21"
630-CFM Fan/Panel Assembly 27"
Leg Levelers—Qty. 4
Casters—Qty. 4
Drawer—3.5" with Lid
Drawer—10" Open
Shelf—18" Sliding
Cage Nuts—Qty. 20
Pan-Head Screws—Qty. 20
Multi-Bay Joining Kit
Adjustable Vertical Mounting Rails for RM3010A and RM3020A
Adjustable Vertical Mounting Rails for RM3030A and RM3040A
Horizontal Mounting Rails for RM3010A and RM3030A
Horizontal Mounting Rails for RM3020A and RM3040A
Louvered Top/Open Bottom for RM3010A and RM3030A
77" Corner Post Pack for RM3010A and RM3020A
Side Panel Pack for RM3010A
Short Steel Door—77"
Louvered Top/Open Bottom for RM3020A and RM3040A
Side Panel Pack for RM3020A
42" Corner Post Pack for RM3030A and RM3040A
3
COMM CABINETS AND ACCESSORIES
Product Code
RM457
RM458
RM459
RM460
RM462
RM464
RM465
Table 2-1 (continued). Available models.
Product Name
Side Panel Pack for RM3030A
Short Steel Door—42"
Side Panel Pack for RM3040A
Plexi Door 77" Locking
Plexi Door 42" Locking
Standard Steel Door—77"
Standard Steel Door—42"
2.2 Kits
When you order the RM3010A, RM3020A, RM3030A, or RM3040A, the following items are included:
2.2.1 W
HAT
’
S
I
NCLUDED WITH THE
RM3010A
• RM339 (Adjustment Rails for RM3010A and RM3020A)
• RM341 (Horizontal Mounting Rails for RM3010A and RM3030A)
• RM450 (Louvered Top/Open Bottom for RM3010A and RM3030A)
• RM451 (77" Corner Post Pack for RM3010A and RM3020A)
• RM452 (Side Panel Pack for RM3010A)
• RM453 (Short Steel Door—77")
• RM323-R2 (Casters)
2.2.2 W
HAT
’
S
I
NCLUDED WITH THE
RM3020A
• RM339 (Adjustment Rails for RM3010A and RM3020A)
• RM342 (Horizontal Mounting Rails for RM3020A and RM3040A)
• RM451 (77" Corner Post Pack for RM3010A and RM3020A)
• RM454 (Louvered Top/Open Bottom for RM3020A and RM3040A)
• RM455 (Side Panel Pack for RM3020A)
• RM453 (Short Steel Door—77")
• RM323-R2 (Casters)
4
2.2.3 W
HAT
’
S
I
NCLUDED WITH THE
RM3030A
• RM340 (Adjustment Rails for RM3030A and RM3040A)
• RM341 (Horizontal Mounting Rails for RM3010A and RM3030A)
• RM456 (42" Corner Post Pack for RM3030A and RM3040A)
• RM450 (Louvered Top/Open Bottom for RM3010A and RM3030A)
• RM457 (Side Panel Pack for RM3030A)
• RM458 (Short Steel Door—42")
• RM323-R2 (Casters)
2.2.4 W
HAT
’
S
I
NCLUDED WITH THE
RM3040A
• RM340 (Adjustment Rails for RM3030A and RM3040A)
• RM342 (Horizontal Mounting Rails for RM3020A and RM3040A)
• RM456 (42" Corner Post Pack for RM3030A and RM3040A)
• RM454 (Louvered Top/Open Bottom for RM3020A and RM3040A)
• RM459 (Side Panel Pack for RM3040A)
• RM458 (Short Steel Door—42")
• RM323-R2 (Casters)
CHAPTER 2: Introduction
5
COMM CABINETS AND ACCESSORIES
2.3 Description
This section describes the products listed in Table 2-1.
• RM3010A: This Comm Cabinet has 77" (195.6 cm) of mounting room and is 30" (76.2 cm) deep for extra rear clearance. It is a modular knock-down cabinet that is easy to assemble and extremely sturdy. The
Cabinet features a handsome black textured finish. Levelers and casters are included in the base package.
Front-mounting rails are pre-drilled and tapped for easy mounting of equipment 10/32 per EIA/TIA standards.
• RM3020A: This Comm Cabinet provides 77" (195.6 cm) of mounting room and is 25" (63.5 cm) deep for extra rear clearance. It is a modular knock-down cabinet that is easy to assemble and extremely sturdy. The
Cabinet features a handsome black textured finish. Levelers and casters are included in the base package.
Front-mounting rails are pre-drilled and tapped for easy mounting of equipment 10/32 per EIA/TIA standards.
• RM3030A: This Comm Cabinet provides 42" (106.7 cm) of mounting room and is 30" (76.2 cm) deep for extra rear clearance. It is a modular knock-down cabinet that is easy to assemble and extremely sturdy. It features a handsome black textured finish. Levelers and casters are included in the base package. Frontmounting rails are pre-drilled and tapped for easy mounting of equipment 10/32 per EIA/TIA standards.
• RM3040A: This Comm Cabinet provides 42" (106.7 cm) of mounting room and is 25" (63.5 cm) deep for standard rear clearance. It is a modular knock-down cabinet that is easy to assemble and extremely sturdy. It features a handsome black textured finish. Levelers and casters are included in the base package. Frontmounting rails are pre-drilled and tapped for easy mounting of equipment 10/32 per EIA/TIA standards.
• RM313-R2: This lock assembly is for steel doors only. It works with all steel-door models.
• RM314: This solid shelf works with cabinets RM3020A and RM3040A. It is rated at 200 lb. (90.7 kg) and has a 1" x 6" (2.5 x 15.2 cm) cable opening in the rear.
• RM315-R2: This vented steel shelf works with cabinets RM3020A and RM3040A. It is rated at 200 lb.
(90.7 kg) and has a 1" x 6" (2.5 x 15.2 cm) cable opening in the rear.
• RM316: This solid steel shelf works with cabinets RM3010A and RM3030A. It is rated at 200 lb. (90.7 kg) and has a 1" x 6" (2.5 x 15.2 cm) cable opening in the rear.
• RM317-R2: This vented steel shelf works with cabinets RM3010A and RM3030A. It is rated at 200 lb.
(90.7 kg) and has a 1" x 6" (2.5 x 15.2 cm) cable opening in the rear.
• RM320: Use this Fan Tray with cabinets RM3020A and RM3040A. It saves valuable vertical mounting space by mounting to the top of the cabinet. The fan assembly exhausts air through the top of the cabinet and consists of a 630-CFM (17.8 m 3 /min.) fan, finger guards, cord, and plug.
• RM321: Use this Fan Tray with cabinets RM3010A and RM3030A. It saves valuable vertical mounting space by mounting on the top of the cabinet. The fan assembly exhausts air through the top of the cabinet and consists of a 630-CFM (17.8 m 3 /min.) fan, finger guards, cord, and plug.
• RM322-R2: These leg levelers are standard on all base cabinet models. They are offered as replacement units. The levelers are made of nickel-plated steel, are threaded, and stand 3" (7.6 cm) tall.
• RM323-R2: These casters are included as standard equipment on all cabinets. They are offered as replacement units. The casters are hard rubber wheels. Each caster can support 200 lb. (90.7 kg).
6
CHAPTER 2: Introduction
• RM324-R2: This 3.5" (8.9-cm) high, 15.6" (39.6-cm) wide sliding drawer has a hinged lid writing surface. It is rated for 95-lb. (43.1-kg) capacity.
• RM325-R2: This 10" (25.4-cm) high, 15.6" (39.6-cm) wide sliding drawer has an open top. It is rated for
95-lb. (43.1-kg) capacity.
• RM326-R2: This sliding equipment or writing shelf is rated for 95-lb. (43.1-kg) capacity. It is 16.75"
(42.5 cm) wide by 18" (45.7 cm) deep. The slides have a lock-out feature for stability.
• RM327: Use these corner posts.
10 ⁄
32
-threaded cage nuts for heavy-duty applications, with 0.281" (7.14-mm) EIA holes on
• RM328-R2: These are
10 ⁄
32
-threaded pan-head screws with a black zinc finish. They are 1" (2.5 cm) long, and include a nylon washer.
• RM329: Use this Kit to join cabinets together to form units with 2, 3, 4, or more bays.
• RM339 through RM342: Use these horizontal and vertical rails if you need additional support on the sides or rear of your rack, or to replace the existing rails if they become damaged. RM339 and R341 can be used with the RM3010 and RM3030; RM340 and RM342 can be used with the RM3020 and RM3040.
• RM450: These replacement top and base pieces can be used with the RM3010 and RM3030.
• RM451: These 77" (195.6 cm) replacement corner posts can be used in tall cabinets (RM3010 and RM3020).
• RM452: This replacement side panel can be used with the RM3010.
• RM453: This replacement back door works with tall cabinets (RM3010 and RM3020). A lower panel allows access for cabling without blocking the door.
• RM454: These replacement top and base pieces can be used with the RM3020 and RM3040.
• RM455: This replacement side panel can be used with the RM3020.
• RM456: These 42" (106.7 cm) replacement corner posts can be used in tall cabinets (RM3010 and RM3020).
• RM457: This replacement side panel can be used with the RM3030.
• RM458: This replacement back door works with short cabinets (RM3030 and RM3040). This is for replacement purposes, since this part is included with the base cabinet assembly. A lower panel allows access for cabling without blocking the door.
• RM459: This replacement side panel can be used with the RM3040.
• RM460: This 77" (195.6 cm) smoked PLEXIGLAS ® door works with racks RM3010A and RM3020A. It includes a lock.
• RM462: This 42" (106.7 cm) smoked PLEXIGLAS door works with racks RM3030A and RM3040A. It includes a lock.
• RM464: This is a steel door for tall cabinets. You can use it as a front door.
• RM465: This is a steel door for short cabinets. You can use it as a front door.
7
COMM CABINETS AND ACCESSORIES
2.4 Products that Work Together
Table 2-2 summarizes which accessories can be used with which Comm Cabinet models.
Accessories
Plexi Door—Locking
Short Steel Door—Vented
Table 2-2. Products that work together.
RM3010A
Comm Cabinet
RM3020A RM3030A
RM460 RM460 RM462
RM453
Standard Steel Door—Vented RM464
Lock—Steel Door Only RM313-R2
RM453
RM464
RM313-R2
RM458
RM465
RM313-R2
630-CFM Fan/Panel Assy.
Leg Levelers-Qty. 4
Casters—Qty. 4
Shelf—Solid
Shelf—Vented
Drawer—3.5" with Lid
Drawer—10" Open
Shelf—18" Sliding
RM321
RM322-R2
RM323-R2
RM316
RM317-R2
RM324-R2
RM325-R2
RM326-R2
Cage Nuts—Qty. 20 RM327
Pan-Head Screws—Qty. 20 RM328-R2
Multi-Bay Joining Kit
19" Rack Power Strip
RM329
PS186A
19" Rack Surge Power Strip SP187A
77" Rack Power Strip PS187A-R2
RM320
RM322-R2
RM323-R2
RM314
RM315-R2
RM324-R2
RM325-R2
RM326-R2
RM327
RM328-R2
RM329
PS186A
SP187A
PS187A-R2
RM321
RM322-R2
RM323-R2
RM316
RM317-R2
RM324-R2
RM325-R2
RM326-R2
RM327
RM328-R2
RM329
PS186A
SP187A
N/A
RM3040A
RM462
RM458
RM325-R2
RM326-R2
RM327
RM328-R2
RM329
PS186A
SP187A
N/A
RM465
RM313-R2
RM320
RM322-R2
RM323-R2
RM314
RM315-R2
RM324-R2
8
CHAPTER 3: Assembly Instructions
3. Assembly Instructions
This chapter provides step-by-step instructions for assembling your Comm Cabinet and related components.
3.1 Comm Cabinets (RM3010A, RM3020A, RM3030A, RM3040A)
3.1.1 P
ARTS
L
IST
Before you begin, open the packages and make sure you have all of the following parts. Refer to Figure 3-3 on page 14 as you install them.
1. (1) top
2. (1) bottom
3. (4) corner posts
4. (2) side panels
5. (1) rear door
6. (1) top access panel
7. (1) rear access panel
8. (8)
3 ⁄
16
-16 x 1
1 ⁄
4
" carriage bolts
9. (8)
3 ⁄
8
" lock washers
10. (8)
3 ⁄
8
" flat washers
11. (8)
3 ⁄
8
-16 hex-head nuts
12. (2) hinges
13. (6) 10-32 x 3 ⁄
8
" round-head screws
14. (4) #10 lock washers
15. (16)
1 ⁄
4
-20 x
1 ⁄
2
" flange-head screws
16. (8) 10-32 x 1" pan-head screws
17. (8) clip nuts
18. (1) door latch
19. (2) 10-32 hex nut with washer
20. (4) 10-32 x
1
⁄
4
" round-head screws
21. (4) horizontal mounting rail
22. (2) adjustable vertical mounting rail
23. (12) spring-loaded tapped nuts [labeled “23a” in diagrams] with hex-head bolts [labeled “23b”]
24. (4) casters
25. (4) leg levelers
26. (1) allen wrench
9
COMM CABINETS AND ACCESSORIES
3.1.2 T
OOLS
R
EQUIRED
You’ll need these additional non-included tools to assemble your Comm Cabinet.
•
3
⁄
8
" open-end wrench or socket
•
9
⁄
16
" open-end wrench or socket
• Phillips screwdriver
3.1.3 A
SSEMBLING THE
C
OMM
C
ABINET
Follow the steps listed below to assemble your Comm Cabinet. Figures 3-1 through 3-3 illustrate the procedure.
STEP 1:
Attach the four corner posts to the cabinet top and bottom. Use the items listed below.
1. (1) top
2. (1) bottom
3. (4) corner posts
8. (8)
3 ⁄
16
" x 1
1 ⁄
4
" carriage bolts
9. (8)
3 ⁄
8
" lock washers
10. (8)
3 ⁄
8
" flat washers
11. (8)
3 ⁄
8
-16 hex-head nuts
A. Lay the cabinet top and bottom on the front edge and position two corner posts to align with the holes and slots in the front corners. Install the carriage bolts with flat washers, lock washers, and hex nuts.
Tighten.
B. Turn the assembly over and repeat STEP 1A for the two rear corner posts
C. If you’d like to do so, install the optional included leg levelers and casters.
D. Lift the frame assembly to an upright position.
STEP 2:
Assemble the rear door and attach it to the corner post. Use the items listed below and at the top of the next page.
5. (1) rear door
7. (1) rear access panel
12. (2) hinges
13. (6) 10-32 x
3 ⁄
8
" round-head screws
14. (4) #10 lock washers
16. (4) 10-32 x 1" pan-head screws
17. (4) clip nuts
18. (1) door latch
10
CHAPTER 3: Assembly Instructions
19. (2) 10-32 hex nuts with washer
20. (4) 10-32 x
1 ⁄
4
" round-head screws
25. (1) allen wrench
A. Use two of the 10-32 x
3 ⁄
8
" round-head screws and two of the lock washers to attach the female portion of each hinge to the rear door. The hinge cavity should face the bottom of the door.
B. Attach the door latch to the door with the two remaining 10-32 x
3 ⁄
8
" round-head screws and the hex nuts with washers.
C. Attach the male portion of each hinge to the left rear corner post using two of the 10-32 x
1 ⁄
4
" round-head screws. The hinge pin must face the cabinet top.
D. Slide the four clip nuts over the appropriate holes on the rear corner post’s mounting flanges to line up with the holes on the rear access panel. Position the rear access panel and attach it with the four pan-head screws.
E. You may install the door now, or after you install side panels, accessories, and electronic equipment. To install the door, simply align its hinges with the hinges on the rear corner post. Adjust the door tension by rotating the allen wrench clockwise until the latch pawl engages the slot in the rear corner post.
STEP 3:
Install the top access panel. Use the items listed below.
6. (1) top access panel
16. (4) pan-head screws 10-32 x 1"
17. (4) clip nuts
A. Slide the clip nuts over the four holes in the flange of the cabinet top.
B. Place the top access panel in the top flange and secure it with the four pan-head screws.
STEP 4:
Install the side panels. Use the items listed below.
4. (2) side panels
15. (16)
1 ⁄
4
-20 x
1 ⁄
2
" flange-head screws
A. Begin to thread the flange-head screws into six holes on the vertical edges of both side panels. Leave at least
1 ⁄
4
" clearance between the screw heads and the side panel. Do not install the screws in two holes in the top edge of the side panels.
B. Carefully align the screw heads with the three keyholes on the sides of each corner post. Hang the side panels without tightening the screws.
NOTE
If you want to be able to remove the side panels in the future, skip steps 4C and 4D.
C. If the side panels are to be secured, install the flange-head screws in the top two holes of both side panels.
Tighten.
D. Tighten all flange-head screws on both side panels.
11
COMM CABINETS AND ACCESSORIES
STEP 5:
Prepare a horizontal mounting rail for installation. Use the items listed below.
21. (1) horizontal mounting rail
23. (2) spring-loaded tapped nuts [labeled “23a” in diagrams] with hex-head bolts [labeled “23b”]
A. Remove the hex-head bolts from the spring-loaded tapped nuts.
B. Place the tapped nut in the channel of the mounting rail, compress the spring, and rotate it to engage it in the channel.
C. Slide the tapped nut to the end of the mounting rail.
D. Repeat steps 5B and C for the second tapped nut. Slide to the opposite end of the rail.
STEP 6:
Install that horizontal mounting rail.
A. Place the mounting rail behind the mounting flanges at the side of the cabinet corner posts.
B. Adjust to the horizontal position at the desired height and insert one of the hex-head bolts you removed in step 5A through the corner post flange and into the tapped nut. (Make sure that the rail is mounted at the proper height for attaching the vertical rails in steps 8 through 10.)
C. Repeat step 6B for the hole at the opposite end of the mounting rail.
STEP 7:
Install the other horizontal mounting rails.
Repeat steps 5 and 6 for the other corner mounting rails.
21
3
23a
23a
3
Figure 3-1. Assembling a horizontal mounting rail.
12
CHAPTER 3: Assembly Instructions
STEP 8:
Prepare an adjustable vertical mounting rail for installation.
22. (1) adjustable vertical mounting rail
23. (2) spring-loaded tapped nuts [labeled “23a” in diagrams] with hex-head bolts [labeled “23b”]
A. Remove the hex-head bolts from the spring-loaded tapped nuts.
B. Place one of the tapped nuts in the channel of the horizontal mounting rail to which you’ll be attaching the vertical mounting rail, compress the spring, and rotate it to engage it in the channel.
C. Slide the tapped nut to the desired location on the horizontal mounting rail.
D. Repeat steps 8B and C for the other horizontal mounting rail that the vertical rail will be attached to.
STEP 9:
Install that vertical mounting rail. (Its drilled and tapped holes should face the front of the cabinet.)
A. Adjusting the height of the vertical mounting rail as necessary, position it so that its “obround” (oblong round) holes align with the threaded holes in the spring-loaded tapped nuts positioned in the horizontal mounting rails. (In steps 6 and 7, you should have mounted the horizontal rails so that the vertical rail can align with them. If not, you’ll need to reposition the horizontal rails.)
B. Insert the hex-head bolts that you removed in step 8A through the obround holes and into the tapped nut. Do not tighten them.
STEP 10:
Install the other vertical mounting rail.
A. Repeat steps 8 and 9 for the other vertical mounting rail.
B. Make sure that all of the rails are properly positioned for your equipment installation, then tighten all hexhead bolts.
21
22
23a
Figure 3-2. Assembling an adjustable vertical mounting rail.
23b
13
14
COMM CABINETS AND ACCESSORIES
6
NOTE: Not all parts are shown here. This is only a representative sampling.
1
15
16
Right
Front
3
17
3
23b
23a
Left
21
11
9
10
22
23b
15
8
2
3
23b
15
3
20
19
18
14
5
12
17
4
7
13
16
Rear
Figure 3-3. Assembling the Comm Cabinet.
3.2 Plexi Doors (RM460, RM462)
3.2.1 P
ARTS
L
IST
Make sure you have the following items before assembling your door.
1. (1) door
2. (1) lock
3. (2) hinge—female
4. (2) hinge—male
5. (6) 10-32 x
3 ⁄
8
" round-head screws
6. (4) 10-32 x
1 ⁄
4
" round-head screws
3.2.2 T
OOL
R
EQUIRED
You’ll need a Phillips screwdriver to assemble and install your door.
CHAPTER 3: Assembly Instructions
3.2.3 A
SSEMBLING THE
P
LEXI
D
OOR
Follow these steps to assemble and install your door.
NOTE
The door mounts to the front left corner post only.
STEP 1:
Attach the hinges to the door. You will need to use the items listed below.
1. (1) door
3. (2) hinge—female
6. (4) 10-32 x
1 ⁄
4
" round-head screws
STEP 2:
Attach the lock to the door. You will need the following items.
2. (1) lock
5. (2) of the (6) 10-32 x
3 ⁄
8
" round-head screws
STEP 3:
Install the hinges to the corner post. Use the following items (refer to Figure 3-4 on the next page).
4. (2) hinge—male
5. (4) of the (6) 10-32 x
3 ⁄
8
" round-head screws
A. Use the holes from the left front corner post.
B. Attach the hinges to the corner post using item 6.
15
COMM CABINETS AND ACCESSORIES
5
4
Figure 3-4. Installing hinges on the corner post.
STEP 4:
Attach the door to the cabinet.
A. Hinge the door by aligning the hinges on the cabinet and the door.
B. Remove the protective paper backing from the PLEXIGLAS door.
3.3 Short Steel Doors (RM453, RM458)
3.3.1 P
ARTS
L
IST
Make sure you have the following items before assembling your door. Refer to Figure 3-5 on page 18 as you do so.
1. (1) door
2. (1) rear access panel
3. (2) hinge—male
4. (2) hinge—female
5. (4) 10-32 x
1 ⁄
4
" round-head screws
6. (4) #10 lock washers
7. (4) 10-32 x 1" pan-head screws
8. (4) clip nuts
9. (1) door latch
10. (2) 10-32 hex nuts with washer
11. (6) 10-32 x
3 ⁄
8
" machine screws
12. (1) allen wrench
16
CHAPTER 3: Assembly Instructions
3.3.2 T
OOL
R
EQUIRED
You’ll need a Phillips screwdriver to assemble and install your door.
3.3.3 A
SSEMBLING THE
S
TEEL
D
OOR
Follow these steps to assemble and install your door.
NOTE
The door mounts to the front or rear left corner post only.
STEP 1:
Prepare the door for attaching to the Comm Cabinet.
A. Use two
1 ⁄
4
" round-head screws and lock washers to attach the female portion of each hinge to the door.
The hinge cavity should face the bottom of the door.
B. Install the door latch to the door with two
3 ⁄
8
" round-head screws and two hex nuts with washers.
STEP 2:
Prepare the cabinet for installing the door.
A. Install the male portion of the hinges in the left rear corner post using two
3 ⁄
8
" round-head screws each.
The hinge pin must face the cabinet top.
B. Slide four clip nuts over the appropriate holes on the rear corner-post mounting flanges to align with the holes on the rear access panel. Position the rear access panel and attach it with four pan-head screws.
STEP 3:
Install the door.
A. To install the door, align the hinges on the rear door with the hinge pins on the corner post.
B. Attach the door latch tension by rotating the included allen wrench clockwise until the latch pawl engages the slot in the rear corner post. Tighten to the desired tension.
17
COMM CABINETS AND ACCESSORIES
11
9
10
1
5
6
4
18
Figure 3-5. Installing the Short Steel Door (RM453 or RM458).
CHAPTER 3: Assembly Instructions
3.4 Standard Steel Doors (RM464, RM465)
3.4.1 P
ARTS
L
IST
Make sure you have the following items before assembling your door. Refer to Figure 3-6 on the next page as you do so.
1. (1) door
2. (2) hinge—male
3. (2) hinge—female
4. (4) 10-32 x
1 ⁄
4
" round-head screws
5. (4) #10 lock washers
6. (1) door latch
7. (2) 10-32 hex nuts with washer
8. (6) 10-32 x
3 ⁄
8
" round-head screws
9. (1) allen wrench
3.4.2 T
OOL
R
EQUIRED
You’ll need a Phillips screwdriver to assemble and install your door.
3.4.3 A
SSEMBLING THE
S
TANDARD
S
TEEL
D
OOR
STEP 1:
Prepare the door for attaching to the Comm Cabinet.
A. Use two 10-32 x
1 ⁄
4
" round-head screws and lock washers to attach the female portion of each hinge to the door. The hinge cavity should face the bottom of the door.
B. Install the door latch to the door with two
3 ⁄
8
" round screws and two hex nuts with washers.
STEP 2:
Prepare the cabinet for installing the door.
NOTE
The door mounts to the front or rear left corner post only.
Install the male portion of the hinges in the left front or rear corner post using two 10-32 x
3 ⁄
8
" round-head screws each. The hinge pin must face the cabinet top.
STEP 3:
Install the door.
A. To install the door, align the hinges on the door with the hinge pins on the corner post.
B. Adjust the door latch tension by rotating the included allen wrench clockwise until the latch pawl engages the slot in the cabinet corner post. Tighten to the desired tension.
19
COMM CABINETS AND ACCESSORIES
8
6
7
1
4
5
3
20
Figure 3-6. Installing the Standard Steel Door (RM464 or RM465).
CHAPTER 3: Assembly Instructions
3.5 Lock for Steel Doors (RM313-R2)
3.5.1 P
ARTS
L
IST
Make sure you have the following items before assembling your lock. Refer to Figure 3-7.
1. (1) latch mechanism
2. (1) lock head with key
3. (2) 10-24 round-head screws
3.5.2 T
OOL
R
EQUIRED
You’ll need a Phillips screwdriver to assemble and install your lock. The lock can be installed on a steel door
(RM453, RM458, RM464, or RM465) only.
3.5.3 A
SSEMBLING THE
L
OCK
Follow these steps to assemble the Lock and install it on a steel door.
A. Position the latch mechanism and the lock head with the holes in the door.
NOTE
The latch pawl must rotate to engage the corner post slot.
B. Insert 2 round-head screws through the latch mechanism and the door and into the lock head. Tighten.
C. Adjust the door latch tension by rotating the key clockwise until the latch pawl engages the slot in the cabinet corner post. Tighten to the desired tension.
Figure 3-7. Installing the lock on one of the steel doors.
21
COMM CABINETS AND ACCESSORIES
3.6 Shelves, Solid and Vented (RM314, RM315-R2, RM316, RM317-R2)
3.6.1 P
ARTS
L
IST
Make sure you have the following items before assembling your shelf. Refer to Figure 3-8.
1. (1) equipment shelf
2. (4) #10-32 x
1 ⁄
2
" pan-head screws
3. (4) #10-32 cage nuts
3.6.2 T
OOLS
R
EQUIRED
You’ll need a Phillips screwdriver to install your shelf.
3.6.3 A
SSEMBLING THE
S
HELF
Follow these steps.
STEP 1:
Install the cage nuts in the corner posts.
Select the desired mounting location for the equipment shelf. Mark the appropriate mounting holes in all four cabinet corner posts. Slide the cage nuts over the marked holes with a nut on the inside of each corner post.
STEP 2:
Install the shelf in the cabinet.
A. Carefully position the equipment shelf so that the round cable opening is toward the rear of the cabinet.
B. Attach the shelf to the corner posts by inserting the pan-head screws through mounting flanges in the front and rear of the shelf and through the cage nuts installed in the cabinet’s corner posts.
C. Tighten the screws to secure the shelf.
22
Figure 3-8. Installing the solid or vented shelf.
CHAPTER 3: Assembly Instructions
3.7 630-CFM Fans (RM320, RM321)
3.7.1 P
ARTS
L
IST
Make sure you have the following parts before assembling your fan. Refer to Figure 3-10 on the next page.
1. (1) top filler panel with fan
2. (4) 10-32 x 1" pan-head Screws
3. (4) 10-32 clip nuts
3.7.2 T
OOL
R
EQUIRED
You’ll need a Phillips screwdriver to install your fan.
3.7.3 A
SSEMBLING THE
F
AN
Follow these instructions to install the fan assembly.
A. Slide the clip nuts over the four mounting holes in the flange of the cabinet top.
B. Place the top access panel in the top flanges and secure it with four pan-head screws.
Figure 3-9. Top filler panel with fan.
23
COMM CABINETS AND ACCESSORIES
NOTE: This is not an installation diagram. The fan comes preassembled and only requires mounting.
Inside of the Cabinet
Outside of the Cabinet
Figure 3-10. Airflow through the fan (exploded view).
24
Figure 3-11. The fan assembly.
CHAPTER 3: Assembly Instructions
3.8 Leg Levelers (RM322-R2)
3.8.1 P
ARTS
L
IST
Make sure you have all four leg levelers before installing any of them. Refer to Figure 3-12.
3.8.2 R
EQUIRED
T
OOLS
No tools are required to assemble the levelers.
3.8.3 A
SSEMBLY
I
NSTRUCTIONS
A. Lay the cabinet on its side.
B. Screw the leveler into the
1 ⁄
2
" diameter threaded weld nuts in the cabinet bottom.
C. Adjust to the desired length.
D. Repeat steps B and C for all 4 levelers.
Figure 3-12. Installing the leg levelers.
25
COMM CABINETS AND ACCESSORIES
3.9 Casters (RM323-R2)
3.9.1 P
ARTS
L
IST
Make sure you have the following parts before assembling the Casters. Refer to Figure 3-13.
1. (4) casters
2. (16)
1 ⁄
4
-20 kep nuts
3. (16)
1 ⁄
4
" flat washers
3.9.2 R
EQUIRED
T
OOL
You’ll need a
7 ⁄
16 open-end or socket wrench to install your casters.
3.9.3 A
SSEMBLY
I
NSTRUCTIONS
Follow these instructions to install the casters.
A. Lay the cabinet on its side.
B. Insert the caster over 4 threaded studs in the cabinet bottom.
C. Secure the caster with a flat washer and a kep nut on each stud.
D. Repeat steps B and C for all 4 casters.
26
Figure 3-13. Installing the casters.
CHAPTER 3: Assembly Instructions
3.10 Drawers (RM324-R2, RM325-R2) and 18" Sliding Shelf (RM326-R2)
3.10.1 P
ARTS
L
IST
Make sure you have the following parts before assembling the drawer or shelf.
1. (1) drawer or shelf
2. (2) slides
3. (2) rear brackets
4. (4) nut bars
5. (4)
1 ⁄
4
-20 x
1 ⁄
2
" Phillips-head screws
6. (4) hex nuts with lock washers (
1 ⁄
4
-20)
7. (8) 10-32 x
1 ⁄
2
" Phillips-head screws
3.10.2 R
EQUIRED
T
OOLS
You’ll need these tools to assemble and install the drawer or shelf.
• Phillips-head screwdriver
• Adjustable wrench
3.10.3 A
SSEMBLY
I
NSTRUCTIONS
Follow these steps to assemble and install the drawer or shelf.
STEP 1:
Install the rear brackets on the slides (refer to Figure 3-14 on the next page).
A. Attach the bracket to the rear of the slide using two
1 ⁄
4
-20 x
1 ⁄
2
" Phillips-head screws and two hex nuts with lock washers. Do not tighten at this time.
B. Repeat step 1A for the other side.
STEP 2:
Attach the slides to the cabinet corner post (refer to Figure 3-14).
A. Select the desired location for mounting the slides to the corner posts.
B. Attach the slide brackets to the inside of the corner posts using the 10-32 x
1 ⁄
2
" Phillips-head screws and the tapped nut bars.
C. Adjust the rear brackets. Tighten all screws.
27
COMM CABINETS AND ACCESSORIES
Figure 3-14. Installing the rear brackets on the slides and attaching the slides to the corner posts.
STEP 3:
Attach the drawer or shelf to the cabinet (refer to Figure 3-15 or 3-16 on the next page).
A. Insert the drawer or shelf into the slides by pressing the drawer or shelf into the bottom part of the slides’ inward-facing component.
B. Push the drawer or shelf assembly inward until the slides are engaged.
C. Pull the drawer or shelf all the way out to check the slide engagement.
STEP 4:
Adjust the drawer or shelf. For smooth slide action, loosen the screws attached to the corner post, adjust the drawer or shelf assembly, then retighten all the screws securely.
NOTE
The drawers come from the factory with their lid installed, but the lid is removable.
28
CHAPTER 3: Assembly Instructions
Figure 3-15. The assembled drawer (RM324-R2 or RM325-R2).
Figure 3-16. The assembled and installed sliding shelf (RM326-R2).
29
COMM CABINETS AND ACCESSORIES
3.11 Cage Nuts (RM327)
There are no special instructions for installing the cage nuts. Use them for heavy-duty applications, with
0.281" (7.14-mm) EIA holes on corner cabinets.
3.12 Pan-Head Screws (RM328-R2)
There are no special instructions for installing the pan-head screws. They are 10-32 threaded pan-head screws with a black zinc finish. The screws are 1" (2.5 cm) long and include a nylon washer.
3.13 Multi-Bay Joining Kit (RM329)
3.13.1 P
ARTS
L
IST
Make sure you have the following parts before assembling the Multi-Bay Joining Kit. Refer to Figure 3-17 on the next page.
1. (6)
1 ⁄
4
-20 hex nuts
2. (6)
1 ⁄
4
-20 x
3 ⁄
4
" hex-Head bolts
3. (6)
1 ⁄
4
" flat washers
4. (6)
1 ⁄
4
" lock washers
3.13.2 R
EQUIRED
T
OOL
You’ll need a
7 ⁄
16 wrench or socket to install your kit.
3.13.3 A
SSEMBLING THE
K
IT
Follow these steps to assemble the kit.
STEP 1:
Prepare the cabinets to be joined.
A. Position the assembled Comm Cabinets side by side with the side panels removed.
B. Align the three keyholes in the vertical corner posts.
STEP 2:
Join the cabinet bays.
A. Insert a hex-head bolt through the adjacent keyholes in the corner posts.
B. Install a flat washer, lock washer, and hex nut. Tighten them.
C. Repeat steps 2A and B for all three keyholes in the front and rear corner posts.
30
CHAPTER 3: Assembly Instructions
Figure 3-17. Assembling the multi-bay joining kit.
31
COMM CABINETS AND ACCESSORIES
4. Troubleshooting
4.1 Calling Black Box
If you have difficulty assembling or installing the Comm Cabinet or its accessories, or if you determine that the
Cabinet or any accessory is defective or damaged, do not attempt to alter or repair the unit. Contact Black Box
Technical Support at 724-746-5500.
Before you do, make a record of the problem. We will be able to provide more efficient and accurate assistance if you have a complete description.
4.2 Shipping and Packaging
If you need to transport or ship your Comm Cabinet or any of its accessories:
• Package it carefully. We recommend that you use the original container.
• Before you ship the unit back to Black Box for repair or return, contact us to get a Return Authorization
(RA) number.
32
Letöltés
A nyilvános link frissítve
A csevegés nyilvános linkje frissítve lett. You may view and manage your chat links after registration here.
Dokumentum nyilvános linkje
Hirdetés
