PowerVision
Field Programming Kit
Installation and Operations Manual
00-02-0900
2013-07-31
Section 78
In order to consistently bring you the highest quality, full featured products, we reserve the right to change our specifications and designs at any time. The latest version of this manual can be found at www.fwmurphy.com.
Please read the following information before installing.
BEFORE BEGINNING INSTALLATION OF THIS MURPHY
PRODUCT:
• Read and follow all installation instructions.
• Please contact Enovation Controls immediately if you have any questions.
Table of Contents
Introduction ................................................................................................................................. 1
Purpose ........................................................................................................................1
Installation ................................................................................................................................... 2
(THIS PAGE INTENTIONALLY LEFT BLANK)
Introduction
Purpose
The purpose of this manual is to provide instructions on using this tool as an alternative to purchasing PowerVision to load the compiled file.
The Field Programming Kit (FPK) is a free Windows PC-based program that is used to update software on PV300P, PV350, PV380, PV450, HVS450, PV780 and HVS780 displays using an
ECom CAN dongle or other supported RP1210B devices.
This program does not require PowerVision in order to perform software updates on a PV3xx display.
You must have the compiled bootloader and/or application payload (*.gciBin file) that you intend to upload.
The software is freely distributable.
Section 78
2013-07-31 - 1 -
00-02-0900
Installation
New display configuration files can be uploaded to displays by following the tool installation and connection instructions steps outlined below.
Step Action
1 If you have a Monochrome display (e.g., PV350, PV380 or PV300P) connect the ECOM dongle to the USB port and the display.
If you have a Color display (e.g., PV450, PV750 or PV780) connect the USB-
Ethernet adapters with cross-over cable to both the PC and the display.
2 Connect the display to the harness, and turn on the power.
Continued on next page
Section 78
2013-07-31 - 2 -
00-02-0900
Step
3
3a
Action
Install the ECOM device driver for a 32-bit or 64-bit Windows installation.
Locate this file and double click it to begin the installation:
3b The following screen will appear. Click Next.
3c The Software License Agreement screen will appear. Click the box to accept the License Agreement terms, and click Next.
3d The Destination folder screen will appear. Click Next to install in the default folder, or click Change to choose a different folder. Then click
Install to begin the Installation.
Continued on next page
Section 78
2013-07-31 - 3 -
00-02-0900
Step
3e
3f
3g
Action
Click Finish to exit the Setup Wizard.
Click Start, and locate/click on the PowerVision Field Programming Kit
2.6.
The following screen will appear. Pick the appropriate Hardware Type from the drop down selection list (e.g., Mono Displays or Color
Displays).:
Note
Section 78
2013-07-31
3h For the Communication Type…
IF Mono Displays is chosen… IF Color Displays is chosen…
Choose ECOM Conduit OR
RP1210Conduit, and follow steps 3i through 4.
The system automatically chooses WebConduit, and follow
steps 5a-5e.
RP1210 Conduit is a generic interface for applications involving OEM diagnostic tools typically used in the heavy-duty equipment.
The RP1210 devices we tested are:
CAT Communication Adapter 3
CAT Communication Adapter II
Cummins Inline 5
- 4 -
00-02-0900
Step
Note:
3i
Monochrome
Display Only
Action
Steps 3i through 4 are used for Monochrome displays only. Steps 5a through 5e are used for the Color Conduit only.
Click on the Setup link, and the following screen will appear:
3j
Monochrome
Display Only
3k
Monochrome
Display Only
3l
Monochrome
Display Only
Select the ECOM Serial Number by pulling down the list. Click OK.
Ensure the Communication Type is “ECOM Conduit”.
Note: RP1210 Conduit is a generic interface for applications involving
OEM diagnostic tools typically used in the heavy-duty equipment.
The RP1210 devices we tested are:
CAT Communication Adapter 3
CAT Communication Adapter II
Cummins Inline 5
Click the Selected Load File link to pick the load file. Ensure that the file type is “Firmware Files (*.gciBin)”.
Select the configurationFull.gciBin file and click Open (or double-click the file).
Continued on next page
Section 78
2013-07-31 - 5 -
00-02-0900
Step
3m
Monochrome
Display Only
Action
Ensure the Connected to: field shows the hardware. This displays that everything is talking.
Click Load. 3n
Monochrome
Display Only
3o
Monochrome
Display Only
The Caution light on the hardware will begin flashing yellow, and the progress will flash vertically on the screen.
4
Monochrome
Display Only
Note:
5a
Color
Conduit Only
Once the display reaches 100%, the unit will reboot, “Success” will be displayed at the top of the status list, and the gauge screen will be displayed on the unit.
If you chose Monochrome Display in Step 3G above, stop here. If you chose Color Conduit in Step 3G above, begin with Step 5a below.
After choosing Color Conduit, this screen appears. Click Setup.
Section 78
2013-07-31 - 6 -
00-02-0900
Step
5b
Color
Conduit Only
Action
Note:
Enter the appropriate IP Addresses, and click OK.
Ensure the Connected to: field shows the hardware. This displays that everything is talking.
Click Load. 5c
Color
Conduit Only
5d
Color
Conduit Only
The Caution light on the hardware will begin flashing yellow, and the progress will flash vertically on the screen.
5e
Color
Conduit Only
Section 78
2013-07-31
Once the display reaches 100%, the unit will reboot, “Success” will be displayed at the top of the status list, and the gauge screen will be displayed on the unit.
- 7 -
00-02-0900
