SMC AMF150C to 550C、AMF650、850 Order Removal Filter Owner's Manual
Add to my manuals
1 Pages
SMC AMF150C to 550C、AMF650、850
The SMC AMF150C to 550C、AMF650、850 is an odor removal filter that can be used to eliminate odors from compressed air. It has a filtration rating of 0.01 μm and an outlet cleanliness of 100 or less / ft3 of 0.3 μm or more of particles. The filter can be used with air pressures between 0.05 MPa and 1.0 MPa, and it has a maximum operating temperature of 60℃. The filter should be installed vertically and should be flushed with air before use.
advertisement
OPERATION MANUAL
ODOUR REMOVAL FILTER Series AMF
To get the best performance from your purchase, be sure to read this manual carefully before use.
Refer drawings or catalogue for construction and specifications.
Understand this operation manual will be revised without notification.
/ MERITS
・Activated carbon fiber element eliminates odour from compressed air.
・Filtration rating:0.01 μm (Filtration efficiency:99.9%)
・Outlet cleanliness: 100 or less / ft 3 of 0.3 μm or more of particle
(35 or less / 10L (ANR))
/ HINTS ON CORRECT USE
Keep following to operate Odour removal filter properly.
①Do not use under following environment.
Chemicals Corrosive gas + Atmosphere
Containing organic solvent
Environment
Lower than 5℃ ! WARNING
Environment
Higher than
60℃
Following environments lead to cause breakage.
Vibration,
Impact
Broken pieces injuring if broken.
②Do not use under following conditions.
Fluid other than compressed air Air pressure more than 1.0 MPa* and
0.05MPa or less
Air only !
! WARNING
Following environments lead to cause breakage.
* Option H: 1.6 MPa
( Only 150C ∼ 550C )
Place where more than 0.1 MPa of intermittent pressure drop occurs.
Over rated flow Place where air flows backwards
No back flow
! WARNING
Following conditions
③Precautions for installation.
・Install vertically.
・Flush inside of pipings with air.
・Ensure no leakage.
IN
Cause element breakage
・Keep sight glass in front.
※Never fail to install one of
OUT
“AMD”, “AMH”, “AME” as a pre-filter.
Never fail to use dry air. Deodorization may deteriorate
if water drop is contained in compressed air.
/ MAINTENANCE
Since element life depend on odour concentration of compressed air, it can not be specified. Confirm deodorizing capacity remaining period, and replace the element periodically afterwards. However, replace element with new one when element has beenused for 2 years, or when pressure drop reaches 0.1 MPa.
Element ass’y (gasket, o-ring accessory) model number: AMF-EL***
※ *** is AMF size symbol. (ex.: AMF-EL150)
【How to replace element ass’y】
First, discharge the pressure in the body. (Make pressure 0 MPa.)
O-ring
(New)
Hexagon socket head bolt
①Remove four hexagon socket
Gasket head bolt.
②Replace element, gasket, o-ring.
(New)
O-ring
(Used)
③Tighten hexagon socket head bolt.
Reference table production no. showing production month and
Element
(New) year of a filter.(Mo→2008.1)
SYMBOL M N o ・・・ Z
Case
Gasket
(Used)
Element
(Used)
Year 2008 2009 2010 ・・・ 2021
SYMBOL o P Q ・・・ Z
Month Jan Feb Mar ・・・ Dec
Phone: +81 3 5207 8249 Fax: +81 3 5298 5362
Specifications are subject to change without prior notice and any obligation the part of the manufacturer
2008 SMC Corporation All Rights Reserved.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement