Roadtrek 210 Popular 2015 Owner's Manual

Owner's Manual
2016 210 Popular
Roadtrek, Inc.
PDF generated at: Thu, 10 Dec 2015 13:44:10 EST
Contents
Articles
Introduction to your 210 Popular
1
Copyright
2
Do's and Don'ts
3
Before you head out
8
Coming Home
9
Interior Living Space
11
Sleeping Facilities
22
Bathroom Facilities
26
Appliances
31
Outside your Roadtrek
35
Utilities
43
Propane System
48
Heating and Cooling
50
Electrical System
53
Monitor Panel
59
Distribution Panel
64
Alarms and Warnings
65
Maintenance
68
Spare Tire Storage
72
Obtaining Service
74
Specifications
75
Warranty
77
Registration
81
Regulatory Notices
83
HOWTO: Monitor Panel
84
HOWTO: Setting Up Your Campsite
91
HOWTO: Shore Power
95
HOWTO: Potable Water Use
99
HOWTO: Waste Water Dumping
104
HOWTO: Cable and TV Reception
111
HOWTO: Propane System
115
HOWTO: Summer and Winter Mode
116
HOWTO: Water System Winterizing
124
HOWTO: De-Winterizing
133
Introduction to your 210 Popular
1
Introduction to your 210 Popular
Congratulations on the purchase of your Roadtrek and welcome to the Roadtreking family. The information included in this
manual is meant to help and guide you through the use of your vehicle so that you know how to properly use the many
functions your Roadtrek has to offer.
Please keep this manual in your vehicle as a reference for when you are travelling. If you have any questions or comments on
information found in this document please contact us at [email protected] [1] or 1-888-ROADTREK.
References
[1] mailto:manuals@roadtrek. com
© 2015 by Roadtrek, Inc.
Copyright
2
Copyright
This manual is released under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0
International License [1].
In summary, you may:
• Copy any portion of this manual in any form for personal use;
• Distribute this manual complete with all of its original unmodified content;
• Modify this manual for your own personal, non-commercial use.
You may not:
• Use this manual for any commercial use whatsoever;
• Modify this manual except as provided for in the full license and then distribute the resulting work;
• Charge for this manual other than reasonable media and shipping costs.
All images used in this manual remain the property of Roadtrek, Inc. They are for illustrative purposes only and may or may
not be representative of the upfits in your Roadtrek.
Contact Roadtrek, Inc. for alternate licensing arrangements if you want to use or distribute this manual commercially.
References
[1] http:/ / creativecommons. org/ licenses/ by-nc-nd/ 4. 0/
© 2015 by Roadtrek, Inc.
Do's and Don'ts
3
Do's and Don'ts
Symbol Legend
For your information. May be useful information to know.
Warning. Not following this can lead to bad results.
Caution. You really should follow this to avoid bad results.
Don't do it. Doing this can result in injury, severe damage, or death.
Information, cautions, and warnings
Level
Item
Comment
SEAT BELTS
Use only forward facing seats equipped with factory installed seat belts while the vehicle is in
motion. All passengers must be seated in these seats only, with the seat belts fastened while
the vehicle is in motion.
TV
Turn the TV off and stow it while the vehicle is in motion.
TV
The flat screen TV should not be stored inside the Roadtrek in cold temperatures. Remove it to
reduce the chance of damage from the cold. Check the Owner's Manual for the TV for storage
and operating temperatures.
© 2015 by Roadtrek, Inc.
Do's and Don'ts
4
TV
To remove the TV, remove the four mounting bolts on the back of the TV mounting bracket
and remove the RCA cables, power supply cable and antenna cable.
PROPANE
Do not store propane tanks inside your vehicle. Propane tanks are equipped with safety
devices which relieve excessive pressure by discharging gas to the atmosphere.
PROPANE
Do not refuel the propane tank to more than 80% of its capacity.
PROPANE
The propane tank valve must be closed and ALL PILOT LIGHTS, APPLIANCES, AND THEIR
IGNITERS, MUST BE TURNED OFF during refueling of the motor fuel tank and/or the propane
fuel tank. Only qualified personnel should refuel your propane tank.
PROPANE
Purchase propane from a reputable propane facility. Contaminated propane is a common
cause of system failure and is not covered under any warranty.
PROPANE
The BBQ quick disconnect is regulated to 10 P.S.I. Please ensure that all devices connected to
this are either rated for “high pressure” or have their own regulator. Many grills sold in the
United States are "low pressure" (1/2 P.S.I.) and will require an additional regulator to step the
pressure down to a useable level. If hooked directly to the BBQ quick disconnect they will be a
severe fire hazard.
PROPANE LEAK
DETECTOR
Do not block the air circulation in the area where the Propane Leak Detector is located.
PROPANE LEAK
DETECTOR
Battery disconnect switch must be in the “ON” position for the propane detector to function.
© 2015 by Roadtrek, Inc.
Do's and Don'ts
5
FLAMMABLE
LIQUIDS AND
GASSES
Do not store gasoline or other flammable liquids inside your vehicle.
HEATING
Never use cooking appliances or unvented propane heaters for space heating purposes. They
need fresh air for safe operation.
HEATING
The heating furnace provides its own outside combustion air and exhausts to the outside.
HEATING
Portable fuel burning equipment, including wood, charcoal, and liquid fuel grills and stoves,
should not be used inside your vehicle. Use of this type of equipment inside your vehicle may
cause a fire or asphyxiation.
CARBON MONOXIDE Do not block the air circulation in the area where the Carbon Monoxide Leak Detector is
LEAK DETECTOR
located
CARBON MONOXIDE Battery disconnect switch must be in the “ON” position for the Carbon Monoxide Leak Detector
LEAK DETECTOR
to function.
110 VOLT
ELECTRICAL
SERVICING
Prior to servicing the 110 volt Galley GFCI & Audio/Video cabinet interior receptacles, unplug
the output lead from the power inverter.
EXTERIOR ACCESS
DOORS
Ensure the shore power cord and city water supply lines are disconnected and in their stored
positions before the vehicle is put in motion.
© 2015 by Roadtrek, Inc.
Do's and Don'ts
6
AWNINGS
Close the sliding side door prior to opening or closing the awning.
CLOVERLEAF
DINING TABLE
The cloverleaf dining table is heavy. Use proper lifting techniques.
EXTRA COUNTER
SPACE
Make sure the stove is off and has cooled prior to lowering the stove cover.
BATTERY
Battery acid can burn your skin and damage clothing. Protective eye wear and gloves should
be worn while handling batteries. Effective June 2010 all Roadtrek installed batteries
are sealed AGM batteries that do no require the addition of water.
BATTERY
Disconnect the inverter/charger prior to disconnecting the auxiliary battery.
GENERATOR
Never submerge the generator. Use a spotter when launching a boat or crossing streams.
GENERATOR
When using the generator as the main power source to run the appliances, refer to the
generator owner’s manual for proper use and maintenance.
GENERATOR
The generator cannot run all the appliances at the same time.
© 2015 by Roadtrek, Inc.
Do's and Don'ts
7
WASTE WATER
STORAGE AND
DUMPING SYSTEM
Close both the black and gray water gate valves before using the waste water system.
FREEZING
Under moderate subfreezing conditions, antifreeze is required in the exterior fresh water tank,
black and gray waste water tanks. Use RV antifreeze in accordance with the manufacturer's
instructions.
ELECTRICAL
SERVICING
This unit has 12 volt, 110 volt and potentially 36 volt solar system. These systems need to be
disconnected before working on them.
GENERATOR
The generator is not compatible with E-85 fuel. If the vehicle is equipped with a generator,
avoid the use of E-85 fuel.
ENGINE BATTERY
The Chevrolet engine battery will be drawn down by the GM electronics to a no-start condition
if left unattended for extended periods. Plug the vehicle in, drive the vehicle for at least three
hours every two weeks to keep the engine and auxiliary batteries charged, or disconnect the
engine battery to keep it in good condition. Battery maintenance is the vehicle owner’s
responsibility.
© 2015 by Roadtrek, Inc.
Before you head out
8
Before you head out
Your new Roadtrek is ready to go with just a little bit of preparation.
To prepare for your first trip, you should:
• Read this manual.
• Contact your dealer with any questions.
• Plan your trip.
Then use this quick checklist.
• The day before your trip:
• charge your batteries by plugging in overnight
• cool your refrigerator by turning it on
• chill any beverages in your home refrigerator
• fill your fresh water tank with clean tap water
• The day of the trip:
• Load the refrigerator with cold food (from your home refrigerator)
© 2015 by Roadtrek, Inc.
Coming Home
9
Coming Home
When you come home, there are a few maintenance tasks you should do to get your Roadtrek ready to go for next time.
Refer to other sections in this manual for the procedures listed here.
• On your way home, dump the gray and black tanks at a convenient facility. See the HOWTO: Waste Water Dumping section
for a concise description of the procedure to do this. Some RV parks and gas stations will let you dump for a fee, some city
wastewater plants will let you dump for free, but there is no real pattern, so local knowledge is vital in locating dump
stations. The website http:/ / www. sanidumps. com is a good resource. The maps for each state and province are
especially helpful: http:/ / www. sanidumps. com/ maps/ help. php
• At home, flush the water tank and fill it with fresh chlorinated water if you will be using it in the next few days. Otherwise,
drain the tank. Don't let water you are planning to use sit in your tank for more than a week or so, and don't let ANY water
sit in your tank for more than two weeks, whether you plan on using it or not. Over time, the chlorine goes away, and the
microbes come out to play.
• To flush the tank, fill it using the gravity fill in the driver's doorframe, and open the fresh water tank drain under the rear of
the driver's doorstep.
Gravity fill in driver's doorframe
Fresh water tank drain, under driver's
doorstep
© 2015 by Roadtrek, Inc.
Coming Home
10
• Plug in overnight to fully charge batteries.
• Turn off and clean out the refrigerator and prop the door open to let it air out
• Turn off two important switches to keep from draining your batteries
• the battery disconnect switch on your monitor panel
• the inverter switch, either on your monitor panel with the standard inverter, or just to the left of it on the separate
inverter switch if you have a big inverter
Battery disconnect switch
Standard inverter switch
Inverter switch for big inverter
• If you turn everything off and you have solar panels, the panels will keep your coach batteries topped up while your
Roadtrek is parked. If you don't have solar panels, it would be prudent to check your coach battery state of charge every
month or so and charge them if necessary. If you don't turn everything off, even with solar panels, you will probably come
back to dead batteries.
That's it! You're ready for the next trip.
© 2015 by Roadtrek, Inc.
Interior Living Space
11
Interior Living Space
Cabinets
Cabinet latches in your Roadtrek are different from the ones in
your home and more like those on boats - they have to stay
closed when the vehicle is in motion. The cabinet doors are
secured with latches located along the edge of the cabinet door.
Run your fingers along the edge and you will find the latch. Press
the latch in and open the door.
To close a cabinet door, shut it gently until you hear the latch
click shut. You may need to press on the latch to get it to latch
closed.
Do not slam the cabinet door in order to latch it - this
will damage the latch.
Do not keep large, round, and/or heavy objects in a
cabinet unsecured - they will roll around and apply
excessive pressure to the inside of the cabinet doors as you
Hidden latch along edge of cabinet door
drive. Even if the force of such objects doesn't break the
latch, they can shift position with vehicle motion and be
leaning against the inside of the cabinet door, waiting to fall when you open the cabinet. For this reason, Roadtrek
recommends that you not store anything in the overhead cabinets that you wouldn't want to get hit over the head with.
© 2015 by Roadtrek, Inc.
Interior Living Space
12
Galley cabinets
Immediately beneath the galley countertop there is a drawer
with a pull knob to the right of the food preparation surface to
hold silverware and small cooking utensils. The left panel is
fixed, and is not a drawer.
The two cabinets below this panel on the left provide storage
space for food and larger cooking utensils. The water heater is at
the bottom of the left cabinet, but there are shelves above this,
and more shelves in the right cabinet for the entire height of the
cabinet. There are three more drawers on the right below the top
drawer and the pull-out table, with hidden latches on the right
side, by the driver's seat.
Galley cabinets
© 2015 by Roadtrek, Inc.
Interior Living Space
13
Lights
Fluorescent light
LED tap light
All cabin lights use 12 volts and are powered by the coach batteries, so the battery disconnect switch must be on for any of
these lights to work.
The fluorescent lights turn on and off with the integrated switch at one end of the light fixture. There are three fluorescent
lights down the center aisle, and one more over the galley.
The four oval and round LED ceiling lights in the back and the two more oval lights over the driver and passenger seats up
front are all individually controlled, and are tap lights - to turn them off or on, press on the lens area. These LED lights use
very little energy, and a good way to conserve battery power is to use them, rather than the fluorescent lights, whenever
possible.
© 2015 by Roadtrek, Inc.
Interior Living Space
14
Tables
Rear dining area
Front lounge area
There are front and rear tables to use either the front or rear lounge areas for dining, playing cards, or computer use.
© 2015 by Roadtrek, Inc.
Interior Living Space
15
Front Table
Front table in cabinet
Front table in place
The front table top slides out from the galley cabinet. It does not have a table leg.
To stow the front table, slide it back into the cabinet.
© 2015 by Roadtrek, Inc.
Interior Living Space
16
Rear Table
Table leg stowed
Rear table T-Nut
Rear table set up for use
The rear tabletop is stored under the driver's side rear bench seat, and its leg is stored within the wardrobe.
The dining table for the rear seating area is located under the driver's side rear bench cushion, directly across from the TV.
Lift the cushion and remove the table top. The table leg is stored in the narrow ledge above the passenger side door. Unscrew
the T-nut on the end of the leg fully. Insert the T-nut into the slot in the table leg base. Rotate the leg clockwise until you feel
it tighten. Pull on it to check that is is secured. If not, extend the T-nut fully by unscrewing it, and try again. Place table top on
the table leg so that the top of the leg fits into the socket underneath the table.
Store the table top under the cushion with the socket seated in the hole in the side bench base, and return the table leg to
the proper location and clip into place for proper storage.
© 2015 by Roadtrek, Inc.
Interior Living Space
17
Front Captain's Seats
The two captain's seats in the front of your 210P are adjustable
fore and aft by pulling up on the bar under the front of the seat,
and will swivel when the swivel tab - the black metal bar on the
side of the chair base - is pulled up. Always return the seats to
the forward-facing position when driving. They will lock into this
position, and stay locked until the swivel tab is raised again.
To create a front lounge area, loosen the recline adjustment and
move the backs of the seats to a vertical position. Do not
attempt to pivot a reclined seat. Use the fore-and-aft adjustment
while swiveling the seats to allow the sides of the chairs to clear
the armrests on the vehicle doors, the engine cover, and other
obstructions. Do not force the seats around. Swiveling the
driver's seat may require you to loosen the tilt steering wheel
adjustment and move the steering wheel as far forward and up
as possible. Opening the front doors slightly will facilitate
clearance of the door armrests.
Front seat swivel tab, just below lumbar support control
Second Row Seat
If you have the standard bathroom, you have a third seat just inside the side door. Enclosed bathroom models do not have
this seat. The second row seat has an adjustment to the seat back and bottom cushion to change the seat back angle for
more comfortable seating. The back lifts up and is held by a pin in a slot (see photo below). The seat bottom cushion can be
lifted and moved forward approximately three inches (8 cm) to its alternate position because of the way it is mounted to the
seat base. Moving the bottom cushion forward and flipping the small panel at the base of the seat back out will configure the
second row seat in a more reclined position.
© 2015 by Roadtrek, Inc.
Interior Living Space
Second row seat back pin and slot
18
Back seat configured in reclined position
© 2015 by Roadtrek, Inc.
Interior Living Space
19
Ventilation
Your Roadtrek is equipped with a ceiling mounted ventilation
fan.
The fan has a cover that must be raised by turning the large
knurled knob before the fan will operate. Raise the cover, then
use the remote to set the desired speed and temperature.
There is also a fuse in the body of the fan, in addition to the fuse
in the distribution panel. Check both this fuse and the one on the
12 volt fuse panel if your fan stops working.
For more details, please refer to the fan manual.
When using the aisle shower, leave the fan off, or the
shower curtain will be sucked in and stick to you.
Exhaust fan
© 2015 by Roadtrek, Inc.
Interior Living Space
20
Window Treatments
Skylight covers
Skylight cover storage
Curtains
Curtain rails and clips
© 2015 by Roadtrek, Inc.
Interior Living Space
21
The skylight windows in your Roadtrek can be covered using the covers stored above the side door. Place the cover against
the glass and use the locking tabs to hold it in place. The smooth side faces the interior of the cabin; the side with the smaller
panel attached goes toward the glass.
The window curtains for the regular windows slide on tracks. It's best to use two hands, one at each track, to pull curtains
closed and open.
The curtains have snaps and clips at the end of the track to hold them in place. The front curtain meets in the middle and is
secured with hook and loop fasteners along this edge.
© 2015 by Roadtrek, Inc.
Sleeping Facilities
22
Sleeping Facilities
Your Roadtrek has beds that can be configured as a king bed or twin bed. Experiment with different configurations to find
what works best for you.
Power Sofa
Power sofa switch
Power sofa
The switch to lower the sofa into the bed position is located next to the thermostat on the passenger side in the rear.
The seatbelts for the power sofa are attached to the floor behind the power sofa. In order to use the power sofa as a seating
position while driving, these seat belts must be threaded up through the gap between the seat back and bottom and used
together with the shoulder belts to secure passengers in these seating positions.
© 2015 by Roadtrek, Inc.
Sleeping Facilities
23
Twin beds
King bed
Make sure that there are no obstructions in the travel path both above and below the sofa.
Do not ride the sofa while it is moving.
© 2015 by Roadtrek, Inc.
Sleeping Facilities
24
Twin Beds
You create two twin beds by lowering the sofa. The sofa makes a continuous sleeping surface with the two bench seats,
leaving the center aisle to make it easy to get in and out of bed.
King Bed
Making the king bed
Bed board in place
To make a full size bed, slide the panel under the passenger side bench seat out into the open space between the two bench
seats, and secure it into the notches on the two inner surfaces of the bench seat bases. Move the bottom cushion for the
bench seats together over this panel, and place the vertical cushions for the bench seats between these and the outer walls
of your Roadtrek.
© 2015 by Roadtrek, Inc.
Sleeping Facilities
25
Optional Folding Mattress for Front Bed
Front captain's seat in position for
folding mattress
Folding mattress in position
View from rearview mirror area
To set up a front bed with the optional folding mattress, turn the front passenger side captain's seat so that it is facing
outward toward the front door, remove the second row seat back by lifting it up, and place the folding mattress on the front
and second row seat bottom cushions. When the front seat is in position facing the door, slide it as far back (toward the
center aisle) as possible to accommodate the folding mattress.
This configuration is only possible with the standard bathroom - enclosed bathroom models do not have the second row seat.
© 2015 by Roadtrek, Inc.
Bathroom Facilities
26
Bathroom Facilities
Enclosed Bath
Toilet
Shower curtain
© 2015 by Roadtrek, Inc.
Bathroom Facilities
27
Toilet pedal
Bathroom door pin
Door
The bathroom doors are secured by a pin in each door. To secure the doors for driving, close the left door first, then the right
door, and then push the pins down so that they engage behind the lip at the front of the bathroom floor. This will prevent the
doors from swinging open when the vehicle is in motion.
Toilet
The enclosed bathroom in your Roadtrek contains a marine toilet. To flush the toilet, press the foot pedal located at the
bottom of the front of the toilet bowl.
© 2015 by Roadtrek, Inc.
Bathroom Facilities
28
Shower
Shower connection and knob
Shower curtain track
To take a shower, unscrew the drain stopper in the center of the bathroom floor. Release the hook and loop fastener straps
retaining the shower curtain, and slide the shower curtain along its track to enclose the shower space. Attach the shower
hose to the water outlet just behind the bathroom sink faucet handles, and pull up on the knob on the faucet spout. Adjust
the water to the correct temperature. There is a water cutoff on the shower head to help you conserve water while
showering.
You can shower in the enclosed bathroom by pulling the shower curtain across the shower curtain track near the bathroom
doors, or you can shower in the aisle by extending the shower curtain around the longer loop of shower curtain track which
goes around the ventilation fan in the roof, and opening the drain in the aisle by removing the flat cover plate and
unscrewing the drain stopper.
© 2015 by Roadtrek, Inc.
Bathroom Facilities
Shower curtain
deployed for enclosed
bathroom shower
29
Shower curtain deployed for aisle
shower
Aisle shower drain
When finished, either air or towel dry the curtain before storing it, refasten the drain stopper to prevent the contents of the
gray water tanks from sloshing up into the shower area while driving, and remove the shower hose from the sink connection.
Push the knob back down to change the sink back into normal mode.
© 2015 by Roadtrek, Inc.
Bathroom Facilities
30
Exhaust fan
Outside shower connection
Exhaust fan
The 210 has an exhaust fan in the bathroom. Turn the white handle to open and close the vent, and turn on the fan by
pushing the power button.
Outside Shower
The outside shower is located on the driver's side, towards the rear wheel. See Outside your Roadtrek for more details on
location.
© 2015 by Roadtrek, Inc.
Appliances
31
Appliances
TV and DVD player
TV Bracket release
DVD player
The TV and DVD player are located in the rear on the passenger side.
Both the television and the DVD player use 120 volt current, so the inverter, generator, or shore power must be used. They
are supplied with remote controls.
See the HOWTO: Cable and TV Reception for antenna connections and configuration details.
© 2015 by Roadtrek, Inc.
Appliances
32
Antenna and Cable Connections
There are two antenna connections in the cabinet above the DVD player. One is labeled for the antenna, the other for cable
TV. Connect the cable to the appropriate jack.
TV antenna and cable connections
Rear speaker control switch
Controlling the Rear Speakers
The surround sound system offered in your Roadtrek allows you to control the rear speaker sound in your vehicle. Locate the
speaker switch which can be found in the cabinet above the home theater system.
• Surround Setting: Allows back speakers to function as part of the TV/home theater system
• Off Setting: Turns the rear speakers off
• Automotive Setting: Connects the rear speakers to the front dash radio
If you are experiencing problems with your TV reception while using the over-the-air antenna, check to ensure the
connection to the antenna signal booster located in the cabinet above the home theater system is plugged in.
To ensure power is getting to the antenna, check to see if the blue indicator light on the antenna is illuminated, and
that the indicator light on the power injector in the cabinet above the TV is illuminated.
© 2015 by Roadtrek, Inc.
Appliances
33
Hot Water
The 210 Popular is equipped with a 6 gallon water heater. The heater requires both 12VDC and propane for proper operation.
See Monitor Panel for location and operation of the switch for the heater.
Refer to the Owner's Manual for maintenance.
Refrigerator
The refrigerator is a 3-way electric and propane model which that runs on DC (battery) power, AC (shore / generator) power,
or propane. Propane operation allows you to operate your refrigerator for weeks on one tank of propane while boondocking,
but cannot be used while the vehicle is in motion. While driving, operate the refrigerator on DC 12 volt power - the vehicle
alternator generates more than enough power to run the refrigerator and keep your batteries charged while driving. You can
use AC when plugged into shore power when you don't want to use propane unnecessarily.
Never run your refrigerator on propane while at a gas station. Shut the refrigerator off while at a gas station, and
turn it back on 12 volt DC after pulling away from the pumps. To ensure that neither your hot water heater nor your
refrigerator generate dangerous open flames while handling fuel, always turn the battery disconnect switch OFF when
refueling.
Refer to the Owner's Manual for details of operation.
© 2015 by Roadtrek, Inc.
Appliances
34
Oven
The oven is a standard microwave / convection oven. It operates much the same as the microwave at your house. It is
probably lower powered, so cooking may take a bit longer.
You must 120V AC power available to use the microwave. See Electrical System for details.
Stove
The propane stove needs fresh air for its safe operation. Make
sure to open a window and open turn on the overhead fan for
proper ventilation.
Refer to the Owner's Manual for details of operation.
Galley stove
© 2015 by Roadtrek, Inc.
Outside your Roadtrek
35
Outside your Roadtrek
Awning
Awning power switch
Awning attachment
Stoved awning
Your Roadtrek has an electric roll up awning. The control for the awning is located above the passenger door on the inside.
To open the awning push the rocker switch and the awning will extend. Lower the supports on each side and secure them to
the two attachment points on the side of the Roadtrek. Refer to the awning manual for the proper way of securing the awning
supports to the attachments. To stow the awning, detach the supports, stow them in the awning housing, and retract the
awning. Electrical awnings have the switch inside the passenger door above the side window.
Awnings are susceptible to damage from wind, and for this reason should never be left extended when you are away from the
vehicle. If a thunderstorm or other windy weather is imminent, stow your awning until the wind calms down.
The awning is only powered when the ignition switch is off. To use the awning, turn off the ignition.
© 2015 by Roadtrek, Inc.
Outside your Roadtrek
36
Exterior Access Doors
Battery Access Door
The door just in front of the rear tire on the passenger side is for the batteries. These are maintenance free AGM batteries.
There is no user maintenance possible on these batteries except keeping them charged - you never have to add water to
them.
Driver's Side Doors
Driver's side access doors
Driver's side front access door showing
tank dump valves
Driver's side center access door houses
power cord and waste hose
On the driver's side, there are 3 doors that house items that you will use.
The small access door directly behind the driver's door has the dump valves for the gray and black tanks.
The center door has a storage area for the macerator hose and power cord. The smaller door just in front of the rear tire has
the outside shower.
The rear access door has the shower and cable TV connection.
© 2015 by Roadtrek, Inc.
Outside your Roadtrek
37
Directly above the center access door and below the galley window you will see two vent hatches. The rectangular one is for
the refrigerator and the square one is for the water heater. The water heater will vent hot gasses when the water heater is
running.
Do not block either of these two vents. Dangerous fumes can enter the vehicle if you do.
Since all these sources of open flame are near the fuel fill door on the driver's side, please ensure that all propane
appliances are off when refueling your Roadtrek. In addition to making sure your main propane tank valve is shut
whenever the vehicle is stored or in motion, turn the battery disconnect switch off when refueling - this will disable the
water heater igniter, the refrigerator igniter, and the furnace.
Propane Access Panel
The propane access cover is located in the rear, at the center of the bumper. Flip the side latches to expose the tank valve
and filler.
Propane access cover
Outside shower faucet
© 2015 by Roadtrek, Inc.
Outside your Roadtrek
38
Exterior Shower
The outside shower hose attaches to the faucet inside the rearmost driver's side storage compartment, behind the rear
wheel. This faucet provides hot and cold running water from the same sources as your inside faucets. When finished,
disconnect and store the shower hose and nozzle.
Optional Rear Door Screen
Roadtreks have an optional rear screen which allows you to open the rear doors and get fresh air and a better view, without
bugs coming in or (attended) pets going out. If you ordered this option, look for this screen in the white box that comes with
your new Roadtrek. The screen attaches to the rear door frame and cargo area floor with a zipper and hook-and-loop
fasteners.
Surround with zipper
Hook and loop fastener for bottom edge
of screen
Open the screen and locate the edge with hook and loop material along it. This edge is the bottom, so use the hook-and-loop
strips on the screen to attach it across the bottom of the door opening.
© 2015 by Roadtrek, Inc.
Outside your Roadtrek
Start the zipper on the left side
39
Installed screen
© 2015 by Roadtrek, Inc.
Outside your Roadtrek
40
Start the zipper at each bottom corner by pushing the bottom
stop (the metal end) of the zipper into the two back-to-back
zipper sliders, and zipping the top slider upward.
At the top, close the flap with the hook-and-loop fastener strip
where the zippers meet.
Use the double slider to unzip the bottom of the screen to allow
access to the underbed storage area in the back of the Roadtrek
without disturbing the top section.
To remove and stow the screen, unzip it from the top down.
Unzipping it from the bottom will not allow you to remove it from
the doorframe surround.
Optional Side Door Screen
In addition to the rear door screen, there is also an optional side
door screen which will allow you to keep the side door open for
ventilation without admitting insects. There is a zipper in the
screen so you can enter and exit without removing the screen.
You can access the underbed storage area without
removing the screen
© 2015 by Roadtrek, Inc.
Outside your Roadtrek
Hook and loop fastener for the side door
screen
41
Installed screen
© 2015 by Roadtrek, Inc.
Outside your Roadtrek
42
Locate the screen in the white box that comes with your new
Roadtrek, and shake it out. To orient the screen correctly, look
for the zipper in the screen - hold the screen so that the zipper
goes across near the top and then down the right side. Start the
hook and loop fastener at a convenient corner and work your
way around the perimeter until the screen is secured.
To enter or exit the vehicle through the side door while the
screen is installed, unzip the opening and step through. There is
a zipper tab on either side so you can fasten it behind you once
through.
While sturdy enough to keep insects out, neither this screen nor
the rear screen are designed to resist repeated and persistent
attempts by pets to get out of the vehicle. Do not leave your
pets unattended with the screen in place and the door open.
They may take themselves for a walk.
Access through the screen
© 2015 by Roadtrek, Inc.
Utilities
43
Utilities
Just like your house, your 210 Popular has fresh water, electricity, waste water disposal, heating, and cooling systems. In the
210 Popular, these systems are self contained and travel with you.
Your vehicle should be reasonably level to allow normal operation of the system.
Fresh Water
Standard Edition
Fresh water is contained in two tanks, called the exterior and interior tanks. The exterior tank is underneath the driver's seat
outside the passenger compartment and thus exposed to the elements, so it is susceptible to freezing. The interior tank is
inside the Roadtrek underneath the passenger side bench, and will allow you to carry and use water in mildly sub-freezing
conditions.
Tank isolator valve,shown in open
position (black plastic handle pointed
along the water line)
City water connection
© 2015 by Roadtrek, Inc.
Utilities
44
The two tanks are connected by the tank isolator valve located in the compartment under the driver side bench, to the left of
the refrigerator.
There are two fill locations.
Exterior tank fill location (driver door
pillar)
Interior tank fill location (rear door, right
side)
• The fill for the exterior tank is in the door post of the front driver door, near the door handle. Look for the orange plug in
the fill port. With the tank isolator valve CLOSED (handle across the line), running water into the fill port will fill the exterior
tank only - approximately 20 gallons.
• The tank selector valve determines which tank the water pump draws water from. It is a long handle with a plastic cover,
usually red or yellow in color, located in the compartment under the driver's side bench, to the left of the refrigerator. See
photos below for how to position the valve to draw from the exterior or interior tank. In summer mode, this handle is in the
exterior tank position, and the tank isolator valve is open.
© 2015 by Roadtrek, Inc.
Utilities
45
Tank selector valve in exterior tank position
Tank selector valve in interior tank position
• To fill the interior tank only, close the tank isolator valve and set the tank selector valve to the interior position. The interior
fill is located in the rear door on the right side. With the tank isolator valve closed, running water into this fill port will fill
the interior tank only - approximately 10 gallons.
• To fill both interior and exterior tanks, open the tank connection valve and set the tank selector valve to the exterior
position. Fill exterior tank first, then interior tank.
Roadtrek recommends that you use a dedicated single purpose potable-water hose. These are usually white in color.
Buy a new one and use it only for filling your tanks and connecting to city water. View any hose lying around a
campground with extreme skepticism, especially it there's a wastewater dump nearby. Large RVs use hoses to flush
their wastewater system. Always flush faucet and hose thoroughly before use.
© 2015 by Roadtrek, Inc.
Utilities
46
City Water
Your Roadtrek can operate in either fully self-contained mode, or can be connected to a water supply such as a campsite's
faucet.
The city water connection is in the driver's side rearmost compartment. Unscrew the white plastic protective cap and connect
your clean hose to the water faucet and a water pressure regulator attached to this connection point. Turn the faucet on and
check for leaks, tightening the connections as necessary.
For more details, please refer to the HOWTO: Potable Water Use section.
Summer and Winter modes
The water system in your Roadtrek has an exterior and interior water tank. In summer mode (above freezing) both tanks can
be used. In mildly sub-freezing conditions, the exterior tank must be drained and the system set to winter mode. See the
HOWTO: Summer and Winter Mode for a concise description of how to operate your system in either mode. In temperatures
lower than mildly sub-freezing, or any freezing temperatures when the Roadtrek is not constantly heated, you must winterize.
Summer Use
In summer mode, both the interior and exterior tank are used to store fresh water. The tank isolator valve in the water line
connecting the two tanks is open, and water is drawn from the exterior tank by setting the tank selector valve to the exterior
tank position. As water is used from this exterior tank, the interior tank, which is positioned higher in the vehicle, drains into
the exterior tank by gravity, thus providing you with full use of the combined capacity of the two tanks. The valves to the
outside shower are open, allowing use of that facility as well.
Winter Use
In winter mode, only the interior tank is used to store fresh water. The tank isolator valve in the water line connecting the two
tanks is closed, and the exterior tank is drained. The interior water tank has a capacity of approximately ten gallons, and this
water is protected in moderate sub-freezing conditions by the tank's position inside the heated vehicle. The valves in the
water lines to the outside shower are closed, so it cannot be used, and neither can the city water connection.
© 2015 by Roadtrek, Inc.
Utilities
47
Again, please refer to the HOWTO: Summer and Winter Mode section for instructions on how to configure your water system
in these modes.
Water Pump
To use the water in the tank, you need to turn on the water pump. See Monitor Panel for switch location.
Waste Water
Gray Tank
Galley sink, bathroom sink and shower drain water drains into the gray water tank. The shower and sink have traps to
prevent tank odors from entering the living space. Be sure to replace the screw-in plug in the shower floor after use to
prevent gray water from sloshing up into the shower pan from the gray water tank while driving.
Black Tank
The black water tanks contains toilet waste. Please refer to the HOWTO: Waste Water Dumping section for materials you can
flush down the toilet.
Indicators
The gray and black water tank level indicators on the control panel will give you an approximate indicator of your tank levels.
When the gray water tanks is full to capacity, water will no longer drain down the shower and sink drains, and you need to
dump the tanks before running any more water. If you see fluid below the toilet valve in the bowl of the toilet, your black
water tank is full and also needs to be emptied before further use.
See Monitor Panel for more information.
Close both the black and grey water gate valves before using the waste water system. It is possible for the valves to
open slightly especially after extensive driving. Black and grey water dump valves are accessed through the driver side
storage door.
© 2015 by Roadtrek, Inc.
Propane System
48
Propane System
Propane system
Propane tank cover
Propane tank main shutoff - fill valve
capped with yellow cap
Your vehicle is equipped with a propane system which, when properly handled and maintained, will provide trouble and worry
free operation of your propane fueled appliances.
The propane tank is located across the rear of the vehicle. To access the tank for filling and to turn the main tank shutoff
valve off and on, turn the two retaining tabs on either side of the access cover, located in the center of the rear bumper, and
remove the access cover.
You must close the tank shutoff valve when the vehicle is not in daily use. Further, you must close the shutoff valve
when the vehicle is traveling. Never operate the refrigerator on propane while the vehicle is in motion.
© 2015 by Roadtrek, Inc.
Propane System
49
There is a BBQ quick-connect pigtail secured behind the access
cover. This will allow you to connect a high-pressure grill or
burner to the propane supply of your Roadtrek.
For further reading, including important safety and use tips, refer
to the Propane HOWTO at the back of this manual.
High pressure BBQ pigtail
© 2015 by Roadtrek, Inc.
Heating and Cooling
50
Heating and Cooling
Thermostat
The thermostat controls the air conditioning unit. Set the
thermostat on "cool" and set the desired temperature.
Some models also have a small heat strip in the air conditioning
which will blow warm air, but this produces heat directly from
electricity and is not recommended for heating the cabin for
extended periods of time unless you are attached to shore
power or running the engine. For all other circumstances, use
the regular heating system to heat the cabin. If your unit has the
heat strip option, you can operate it by turning the thermostat to
"furnace" and setting the desired temperature.
The third setting, "fan", recirculates cabin air using the fan inside
the air conditioning unit.
Thermostat
© 2015 by Roadtrek, Inc.
Heating and Cooling
51
Heat Pump
The heat pump can provide both heating and cooling for your
Roadtrek using electric shore power or generator power. The
heat pump gives you the advantage of heating your unit with
electricity if you would prefer to use electricity rather than the
propane the furnace uses.
The heat pump can be operated normally when you are plugged
in to shore power.
If you are running the heat pump using the generator, please
follow the following steps.
• Set the battery disconnect switch on the monitor panel to the
“ON” position.
• Start the generator and run for several minutes until warm.
• Set thermostat setting above ambient temperature.
• Turn thermostat control to the “low cool” position.
• Turn fan to the ON position.
Heat pump
• Adjust the thermostat on the unit for the desired temperature.
The compressor should start automatically.
• Your vehicle should be parked as close to level as possible to maximize the air conditioner’s efficiency. If you are parked
very much off-level, it is possible for condensate to leak into the living space. If this happens park in a more level location.
You can use the heat pump to warm the motorhome on cool nights. For colder temperatures, below 40°F (4°C), you should
use the propane furnace.
© 2015 by Roadtrek, Inc.
Heating and Cooling
52
Furnace
The furnace is controlled by the combination thermostat located
above the rear bed. The furnace requires propane and 12 volt
power. The furnace uses much less electricity compared to the
heat pump, and can be used without shore power or generator
use.
The fan on the furnace is thermostatically controlled, and will
continue to run for a minute or so after you turn it off until the
firebox cools down.
Keep the aisle in front of the furnace clear of any obstructions
when using the furnace to allow air circulation.
The furnace can operate when outside temperatures are below
freezing.
Propane furnace
© 2015 by Roadtrek, Inc.
Electrical System
53
Electrical System
Coach Batteries
The coach batteries in your Roadtrek are sealed AGM (absorbed glass mat) batteries. Do not attempt to open them. There is
no user maintenance possible on these batteries except keeping them charged.
Battery Disconnect Switch
Battery disconnect switch
Engine generator
The battery disconnect switch provides power to all 12 volt appliances, such as the water pump, the refrigerator, and so forth.
Even the propane cooktop uses 12 volt power to run the burner igniters. This switch should be off when you are not using
your Roadtrek, and on whenever you are driving or camping. The "Battery On" light next to it will indicate the position of the
switch.
© 2015 by Roadtrek, Inc.
Electrical System
54
Charging your batteries
Inverter-Charger
Your Roadtrek is equipped with a inverter-charger which converts 120 volt AC (household current) to 12 volts DC when you
are connected to shore power or running the optional gasoline generator. This 120 volt power is used to power your 12VDC
appliances as well as charge your batteries. Whenever you are receiving either source of 120 volt power, you are charging
your batteries.
Standard Alternator Charger and Battery Isolator
While driving, your Roadtrek will also charge the coach batteries from the vehicle alternator through a separator. The
separator allows extra vehicle alternator-produced electricity to charge your coach batteries in addition to keeping your
engine (chassis) battery charged. When the vehicle engine is not running, it breaks the electrical connection between your
coach batteries and your engine battery, so your engine battery remains charged to start your engine even though you are
using coach battery power while camped. This is all automatic - there are no user adjustments possible to the separator.
Optional Engine Generator
Your vehicle may be equipped with an engine generator. The engine generator is mounted on the vehicle engine and is
operated by idling the vehicle engine. If your coach batteries are low, start the vehicle engine and let it idle until the batteries
are sufficiently charged. Usually 30 minutes of idling are enough to restore moderately depleted coach batteries to a useful
level of charge.
As with a conventional generator, always close the rear windows of the vehicle and turn off the roof ventilation fan when the
engine generator is charging the batteries to avoid exhaust entering the vehicle's interior.
The engine generator is charging the coach batteries whenever the vehicle's engine is in operation, which means you are also
charging them as you drive. You will arrive at your camping destination with fully charged coach batteries.
There is no required maintenance for the engine generator. Note, however, that your vehicle's serpentine belt (the belt which
drives the vehicle's alternator, water pump, power steering, etc.) will be different than the one for similar vehicles without the
engine generator, so carrying a spare belt may be prudent in case you have a serpentine belt failure while traveling.
© 2015 by Roadtrek, Inc.
Electrical System
55
Optional Solar Panels
Solar charge controller
Generator switch and hour meter
The optional solar panels will charge your batteries when sufficient sunlight is available. The solar charge controller is
installed at the factory for the type of panels and batteries installed on your vehicle, and Roadtrek strongly recommends that
you make no adjustments or changes to the charge controller or its programming. The charge controller usually displays
either system voltage or amperes generated by the panels.
© 2015 by Roadtrek, Inc.
Electrical System
56
On board 120 Volt AC power
Inverter switch with standard 750 watt
inverter
2500 watt inverter switch
Standard 750 Watt Inverter
The standard configuration includes a 750 watt inverter. This inverter provides 120 volt AC (household current) for a few of
the outlets in your Roadtrek; primarily the ones running the TV and the DVD player. It is not powerful enough to operate the
air conditioner or the microwave.
The inverter is configured at the factory for the batteries and power sources in your Roadtrek. Please do not change any
settings without consulting the factory.
© 2015 by Roadtrek, Inc.
Electrical System
57
Optional 2500 Watt Inverter
If your vehicle has the engine generator option, you also have a 2500 watt inverter. This is sufficient to run all your
appliances. However, running large, high-energy appliances such as microwave ovens, air conditioning, toasters, etc. drains
your batteries very quickly. If you operate these appliances, do so for a limited time unless you also have additional sources
of power.
Instead of the regular inverter switch on the monitor panel, your inverter switch will be on its own smaller panel to the left of
the main monitor panel. The switch has three positions: off in the middle position, power save auto in the top position, and
power save off in the bottom position.
The powersave auto setting is not recommended by Roadtrek. Newer controllers no longer have this setting. Use either OFF
or powersave off settings and turn your inverter on and off as needed.
Pressing the bottom of the switch selects power save off. When this setting is selected, the inverter will be on continuously.
There is a shore power indicator light to the right of the switch to tell you the system is receiving shore power. There is also a
battery charging indicator light to tell you when the batteries are being charged by shore power.
Your refrigerator will run on either 12 volt battery power or 120 volt inverter power.
Optional Gasoline Generator
The gasoline powered generator provides up to 2800 watts of power, enough to run all your appliances. Please refer to the
Onan Generator manual for operation and maintenance.
Always close the rear windows of the vehicle and turn off the roof ventilation fan to avoid exhaust entering the vehicle's
interior.
There is an hour meter to the right of the switch which displays hours of generator use. Maintenance on the generator is
scheduled according to hours of use. There is a break-in oil change scheduled fairly early in your generator's use, so check
your Onan manual for particulars.
Please be sure to operate the generator at half load or more (at least 1200 watts, either the heat pump or an electric
heater) for one hour every month. Failure to do this can lead to internal corrosion, gumming up of the float bowl, and
eventual failure.
© 2015 by Roadtrek, Inc.
Electrical System
58
Shore Power
The shore power connection is through the shore power cord, stored in the driver's side large compartment. See Outside your
Roadtrek for location. The switchover from shore power to inverter is automatic.
To connect to external (shore) power, open the side compartment and remove the power cord. Plug the power cord into the
campsite 30 amp power source. See HOWTO: Shore Power for a concise guide on how to connect and disconnect to shore
power.
Outlets
The outlets are operated from the inverter, generator, or shore
power. Further, the outlets are protected by GFCI. Only some of
the outlets are powered by the standard 750 watt inverter.
The electrical outlets above the galley and under the passenger
side rear captain's seat have ground fault circuitry (GFCI) - the
button in the middle of the outlet pops out when they sense an
anomaly or sometimes when the circuit undergoes transitional
conditions. If you are not getting power from an outlet, check
and reset this button if needed. The outlet under the passenger
side chair powers the TV and DVD player, so check it if your TV is
not receiving power.
GFCI outlet under rear passenger side seat
© 2015 by Roadtrek, Inc.
Monitor Panel
59
Monitor Panel
The monitor panel is located inside the side door, above the
doorframe to the left of the bathroom.
Power Sources
The monitor panel controls 2 separate power sources; the 12
volt DC power and the 120 volt AC power via the inverter, shore
power, or optional generator.
12 Volt DC Power
The power to the 12 volt DC outlets and appliances is controlled
by the battery disconnect switch to the lower left.
On the bottom left is the battery disconnect switch, which
supplies 12 volt battery power to the 12 volt light and other
cabin appliances. This switch must be on for any of the 12 volt
electrical devices to work. Remember to turn off two switches the inverter switch and the battery disconnect switch when your
Roadtrek is not being used to avoid discharging the batteries.
Monitor Panel with standard 750 watt inverter and
optional gasoline generator
The battery disconnect switch has a blue indicator light to the right of it to show you when the battery power is on.
© 2015 by Roadtrek, Inc.
Monitor Panel
60
Battery Disconnect
Inverter switch for standard 750 watt
inverter
Inverter switch for optional 2500 watt
inverter
Inverter
The inverter provides 120 volt AC (household current) to the 120 volt appliances and wall outlets. If you have the optional
engine generator and 2500 watt inverter, your inverter switch is back by the thermostat on the passenger side of the rear
lounge area. See the Optional Engine Generator and 2500 Watt Inverter portion of the Electrical System section for further
information.
© 2015 by Roadtrek, Inc.
Monitor Panel
61
Shore Power
Shore power is the name for power supplied by a utility company that you plug into to provide power to your Roadtrek. See
HOWTO: Shore Power for a concise guide to plugging in and unplugging from shore power.
Other Switches
Patio Light
On the monitor panel, the top left switch is the patio lights switch. Press the top of the button to turn the lights on, and the
bottom to turn them off. These are LED lights and use very little power.
Patio light switch
Water pump switch
© 2015 by Roadtrek, Inc.
Monitor Panel
62
Water Pump Switch
The centered switch to the right of the leftmost four switches is the water pump switch. It should be on only when you have
water in the fresh water tanks and wish to use the sinks, showers, or toilet. The pump should not be run without water. As
with the patio light switch, pressing the top of the button turns the pump on, and pressing the bottom turns it off.
Water Heater Switch
The water heater switch is to the right of the water pump switch. As with all the other switches on the monitor panel, the
battery disconnect switch must be on for the water heater to work. Even though the water heater uses propane to heat the
water, all the igniters and controls are electrical.
Water heater switch
Tank status lights
© 2015 by Roadtrek, Inc.
Monitor Panel
63
Tank and charge indicators
To the right of the monitor panel are the indicator lights for the
the battery charge level, the fresh water tank levels for each
tank, and the black and gray water tank levels. The battery
disconnect switch has to be on for this display to work. Press the
button for each to see the display. These will give you an
approximate reading, to the nearest third, of how much is in
each tank. The four indicator lights for the battery are low, fair,
good, and charging.
Optional Generator Switch and Hour
Meter
If you have the optional 2800 watt gasoline generator, the
switch is to the right of the tank and charge indicators. Press the
bottom of the switch for about five seconds to prime the
generator, then the top to start. Press the bottom again to turn it
off.
Generator switch and hour meter
The hour meter to the right of the switch keeps track of how many hours your generator has been running. There is a break-in
oil change after 20 to 50 hours of operation, and other required maintenance at other intervals later on - see the generator
manual for details.
© 2015 by Roadtrek, Inc.
Distribution Panel
64
Distribution Panel
The distribution panel is located above the side door, just below the monitor panel. The 120 volt AC breakers and the 12 volt
DC fuses are behind a black plastic panel.
Distribution panel
120 volt AC breakers and 12 volt DC
fuses
AC Breaker Panel
The 120 volt breakers are located below the monitor panel behind a black plastic cover. Flip the cover to the right and note
the labels under the cover with the identifying information on each breaker. When storing the Roadtrek for the winter, turn off
the battery disconnect switch and all circuit breakers in this panel.
12 Volt Fuse Panel
The 12 volt fuses are located to the right of the 120 volt AC breakers. The label on the cover has identifying information for
each fuse. These are standard autmotive fuses. Always replace the fuses with the appropriate amperage; never replace a
blown fuse with one of a larger rating.
© 2015 by Roadtrek, Inc.
Alarms and Warnings
65
Alarms and Warnings
Propane and CO alarm
Smoke alarm
Propane and CO alarm
Your vehicle has been equipped with a combination propane leak and carbon monoxide detection device for your protection.
It is located slightly above floor level directly behind the rear bathroom door on the passenger side of the vehicle.
Be sure the detector is operating while using your vehicle, especially when you are asleep inside it.
When storing things on the floor, do not block air circulation to the propane leak detector. You should be able to see it at all
times from the front of the vehicle.
The detector runs on 12 volt power, and is operational whenever the battery disconnect switch is on. There is no separate
switch for the detector. There is an indicator light on the detector so that you can tell whether it's working or not. For this
reason, whenever the vehicle is occupied the battery disconnect switch should be on the "on" position.
Coach power on the Monitor Panel must be on for detector operation. Make sure your battery disconnect switch is
on.
© 2015 by Roadtrek, Inc.
Alarms and Warnings
66
Do not disable, unplug, or otherwise hinder the operation of this detector.
The detector has a useful service life, beyond which it needs to be replaced. See Manufacturer’s Owner’s Manual for
other operating instructions, or look for the sticker which is sometimes placed on the detector to see the replacement
date.
The detector may chirp if the coach batteries are running low.
The Carbon Monoxide and Propane Leak detector is located on the passenger side, near the floor under the TV. These
detectors have a service life, beyond which point they need to be replaced. The detector requires no maintenance other than
periodic replacement. See User Manual supplied with the unit for replacement intervals.
© 2015 by Roadtrek, Inc.
Alarms and Warnings
67
Smoke Alarm
The smoke alarm is located to the right of the Monitor Panel. It requires a 9V battery and periodic replacement. Please refer
to the Owner's Manual for the unit in your vehicle.
Fire Extinguisher
The fire extinguisher is located just rear of the front passenger
seat. It is a dry chemical fire extinguisher suitable for all fires.
Before every trip, check to see that the needle on the dial is in
the green range. If not, replace the fire extinguisher. DO NOT
test your fire extinguisher by discharging it - total discharge time
is 8 to 12 seconds, so it will become rapidly depleted if you test
it this way. Service life on fire extinguishers currently supplied is
12 years; replace the fire extinguisher if it is more than 12 years
past the year of manufacture stamped on the base of the
cylinder.
Fire extinguisher
© 2015 by Roadtrek, Inc.
Maintenance
68
Maintenance
Tires
See the automotive chassis manufacturer's owner's manual and documents for tire warranty information. Inflation pressure
information is on the sticker inside the galley cabinet door. The current Mercedes Sprinter manual recommends checking tire
pressures regularly - at least every other week, and definitely before a long trip. Tire rotation intervals depend on wear and
other factors, but tires should be rotated at least every maintenance interval - every 40,000 km/24,000 miles. Follow the tire
rotation pattern for dual rear wheel models in your owner's manual.
Cargo Carrying Capacity
See the information labels attached to the driver door post, and the inside of the lower galley cabinet door.
Owner Maintenance Checks
Listed below are vehicle maintenance checks and inspections that should be performed by the owner or qualified service
technician at the indicated intervals. Any adverse conditions should be brought to the attention of your dealer or qualified
service technician for expert service advice as soon as possible. The owner maintenance checks are generally not covered by
warranties and you may be charged for labor, parts and supplies used.
© 2015 by Roadtrek, Inc.
Maintenance
69
When You Stop for Fuel, or Weekly
Check engine oil level.
Look for low or underinflated tires.
Every Other Week
Check tire pressure on all tires and your spare.
At Least Monthly
Check coolant level in the coolant recovery reservoir.
Check windshield washer fluid, brake fluid and power steering fluid levels.
Check operation of all exterior lamps, including brake lamps, turn signals and hazard warning flashers.
At Least Every Three Months
Flush black water holding tank. Use a hose or bucket to fill the tank through the toilet, and dump.
Flush grey water holding tank. Use a hose or bucket to fill the tank through the galley sink, and dump.
Flush and sanitize fresh water tank. To flush the tank, fill it completely using the gravity fill, and drain using the freshwater
tank drain underneath the passenger side door sill. Sanitize by adding 1/2 cup chlorine bleach to the tank, fill with water, let
sit for at least two hours, and drain. 1/2 cup vinegar added to the next tankful, which will also be drained before filling with
fresh water for use, will help dissipate the chlorine smell.
Refer to other sections in this manual for drain and fill locations.
© 2015 by Roadtrek, Inc.
Maintenance
70
At Least Twice A Year
Check windshield wiper operation. Clean wiper blades with clean cloth dampened with washer fluid. Wiper blades should be
replaced at least once a year.
Check radiator, heater and air-conditioning hoses for leaks or damage.
Check for worn tires and loose wheel lug nuts.
Check parking brake system - put the brake on and see if it will hold on a moderate hill. If not, get it repaired.
Check head lamp alignment - shine your low beam headlights on a wall. The light patterns should be the same height.
Measure headlight height at the vehicle with a yardstick - the light patterns should be the almost same height or slightly less
with your vehicle level. If not, get the headlights aligned.
Check lap and shoulder belts for wear and function. Replace any belts with frayed spots or that do not smoothly retract into
their holders.
Inspect appliance vents to ensure they are free from dirt, insects, spider webs and/or nests.
Inspect black water tank vent and remove any debris or other obstructions. The black water tank vent is on the roof,
passenger side, in the bathroom area.
Clean air conditioner filter. See air conditioner manual for details.
Thoroughly clean and wax the roof of the van. To wash the solar panel, use a garden hose to rinse dirt off the panel. Do not
scrub it with a brush or otherwise apply any abrasive material to the solar panel surface. Rinsing the panel two or three times
a year to remove excess dirt is all you need to do to keep the panel operating at full output.
With the tanks empty, add one cup of mineral oil and one cup of hot water to the black and grey tanks.
At Least Once a Year
Lubricate all door hinges, locks and latches, especially the exposed hinges on exterior doors. These will freeze up and cause
damage to the doors if neglected.
Have appliances tested and cleaned.
Wax & polish and protect exterior surfaces. The wheels are coated aluminum - there is no bare aluminum on the vehicle, so
do not use aluminum polish on any surface of your Roadtrek. The wheel center caps are chrome.
© 2015 by Roadtrek, Inc.
Maintenance
71
To prevent water from entering your vehicle, avoid spraying water directly into exterior vents or grills. Do not use a power
washer to clean your Roadtrek - damage to the paint, removal of decals, and water leaks will result. Hand washing or
commercial car washes accommodating large vehicles are the best way to keep your Roadtrek clean and shiny.
Other maintenance checks
Follow the maintenance for your appliances per the appliance manufacturer's manual.
© 2015 by Roadtrek, Inc.
Spare Tire Storage
72
Spare Tire Storage
Rear Door Spare Tire
Spare tire retaining pin
Spare tire lift latch
Supplied with your new Roadtrek are two types of small keys. One is for the storage compartments, and the other is
to unlock the chrome surround on your spare tire. Find both keys, put one of each on your key ring, and carry them with
you whenever you drive your Roadtrek. If you ever need to change a tire, you will need this key.
If your new Roadtrek still has the blue coating on the chrome spare tire cover, remove it as soon as you can. If left on
for an extended period of time, particularly in the hot sun, it will become very difficult to remove.
In order to open the driver's side rear door you must lower the spare tire.
To lower the continental kit spare tire and gain access to the driver's side rear door of the Roadtrek, unlatch the retaining
spring and pull the pin out while supporting the top of the tire with your other hand. It helps to wiggle the tire back and forth
to allow the pin to slide out. Place the pin where you won't lose it, and grasp the top of the tire with both hands. Lower it into
a horizontal position to allow the driver's side rear door to open freely. The tire will latch when horizontal.
© 2015 by Roadtrek, Inc.
Spare Tire Storage
73
While the tire is spring loaded it is still fairly heavy. Use proper lifting technique or get help.
To raise the spare tire back into position, lift the guard over the cable mechanism enough for the catch to clear and allow the
tire to be raised. Raise the tire back up into position, and insert the pin. Flip the retaining spring over the end of the pin to
secure it.
To use the spare tire, lower the tire, unlock the chrome surround with the key supplied with your Roadtrek, unbolt the tire
from the carrier with your lug wrench, and lift the tire off the carrier. Follow the Chevrolet manual for instructions on the use
of the jack and other tire change procedures. Install the flat tire on the spare tire carrier and reattach the chrome surround.
Do not attempt to raise an empty tire carrier - if you change the tire, put the flat on the carrier before attempting to
raise it. NEVER release the latch on a tire carrier without a tire on it. The spring will move the arm of the carrier upward
with great force and speed.
© 2015 by Roadtrek, Inc.
Obtaining Service
74
Obtaining Service
When your Roadtrek needs service, determine if the issue is with the Roadtrek upfits or the
GM Chassis.
For Roadtrek upfits, contact your Roadtrek dealer. Start with the service writer, then the
service manager, and lastly, if you are unable to resolve your issues with the service
department, contact the dealership managing partner or owner. Please keep notes of who
you spoke with and dates.
For chassis-related issues, contact GM service. Advise the service writer that you have a
G-30 1 ton van, rather than a "motorhome". Some GM dealerships do not want to work on
motorhomes, but most can service a 1 ton van. Again, start with the service writer, then
the service manager, and lastly, if you are unable to resolve your issues with the service
department, contact the dealership managing partner or owner. If you cannot resolve your
chassis related issues at the dealer level, contact GM's factory service.
Roadtrek typically cannot initiate a case with the chassis manufacturer; the owner
must do that.
Contact Roadtrek Service after you have exhausted the process above. Please provide as
complete a record as you can so Roadtrek Service does not duplicate effort.
© 2015 by Roadtrek, Inc.
Specifications
75
Specifications
For general chassis specifications, please refer to the GM manual. For specifications relating to your vehicle, including
occupancy, weight rating, tire size, inflation, and so on refer to the sticker on the driver's side B pillar (right side of the door
frame, near the latch). This specification refers to the Roadtrek upfits.
Roadtrek upfits only
Sticker on driver side B pillar
with passenger capacity,
chassis weight and tire specs;
your sticker will be different
© 2015 by Roadtrek, Inc.
Specifications
76
Total fresh water capacity (includes water heater) 36 gallons/ 136 liters
Fresh water tank capacity
30 gallons/ 114 liters
Gray water tank capacity
23 gallons/ 85 liters
Black water tank capacity
10 gallons/ 38 liters
Battery type
AGM, maintenance free
Battery Capacity
190 amp hours (standard)
Propane tank size
10 gallons/ 38 liters
Propane tank capacity at 80%
8 gallons/ 30 liters
Water heater capacity
6 gallons/ 28.5 liters
Furnace
16,000 BTUs/hour
Refrigerator
3-way (propane, 12VDC, 120VAC)
Air Conditioner
10,200 BTUs/hour
440 amp hours (optional)
© 2015 by Roadtrek, Inc.
Warranty
77
Warranty
Chassis Manufacturer's Warranty
The automotive Chassis is warranteed by General Motors. Please refer to the Chevrolet Warranty Information booklet for
details.
All automotive service, maintenance and repairs are to be performed by any Chevrolet dealer. See the Chevrolet Warranty
Information booklet for details. Such items are not warranted by Roadtrek. Roadtrek will pay for the removal and
reinstallation of motorhome components necessary to perform automotive recalls and warranty for the duration of the
original manufacturer's warranty. After this period such costs are considered to be inherent in the ownership of a motorhome
and Roadtrek will not pay for the removal and reinstallation of motorhome components necessary to perform automotive
service or maintenance.
Roadtrek Motorhomes Six Year Peace of Mind Warranty
Roadtrek Motorhomes warrants to the Purchaser that the Motohome is free from defects in material and workmanship on the
portion manufactured by Roadtrek Motorhomes, under normal use and service, for six (6) years, from date of purchase by the
first Purchaser or the date the Motorhome was first put into service (for example, as a demo or rental), whichever is earlier.
This warranty shall be fulfilled at a Roadtrek Motorhomes Dealer or authorized Roadtrek repair facility. For in transit
emergency repairs, you may choose to deal with a non-authorized RV service facility. However all warranty repairs at
non-authorized RV service facilities must be preauthorized by Roadtrek Motorhomes. Roadtrek Motorhomes will, at its option,
replace or repair free of charge (including related labor) any defective part, about which the Purchaser shall notify their
Roadtrek Dealer within the warranty period. The obligation of Roadtrek Motorhomes under this warranty is expressly limited
to such replacement or repair.
The provisions of this limited warranty shall not apply to the following:
1. Accident.
2. Unauthorized repairs or alterations.
3. Normal maintenance.
4. Changes made to other units manufactured after this Motorhome was manufactured. (This is not an engineer upgrade
warranty.)
© 2015 by Roadtrek, Inc.
Warranty
78
5. Incidental damages connected with the failure of the Motorhome such as lost time, inconvenience, loss of use of the
Motorhome, cost of rental cars, gasoline, telephone, travel or lodging.
6. Damages caused by environmental factors including, but not limited to, hailstorms, tornadoes, sandstorms, stone chips,
lightning, floods, earthquakes, airborne fallout, chemicals, tree sap, ocean spray, road hazards.
7. Motorhome that has been declared a total loss by an insurance company (demolished) or a Motorhome whose title
indicates that it is designated as "salvage", "junk", or "rebuilt" or words of similar impact.
8. There will be no allowance for emergency road repair, towing, labor, meals accommodations, etc. Such will not be
accepted if claimed under warranty.
9. Aluminum wheels are not warranted against corrosion that is a result of road salt, sea salt, cleaning chemicals or harsh
driving conditions.
10. Warranty is voided if the EcoTrek batteries are tampered with, opened, or modified in any way, including attempts to
change the Battery Management System programming or setpoints.
11. Warranty is voided if the EcoTrek batteries are allowed to remain in a dicharged condition for extensive periods.
The provisions of this limited warranty shall not apply to deterioration due to wear and exposure beyond the following
limitations:
1. For ninety (90) days after the "QualityCare" Pre-Delivery Report is completed by the dealer for appliance adjustments,
door latch adjustments, light bulbs, fuses, battery in the smoke detector and window screens. After 90 days these items
are considered part of normal maintenance.
Roadtrek Motorhomes Limited Motorhome Warranty is void unless the following conditions are adhered to:
1. Warranty Card on Motorhome must be completed by the Dealer and faxed to Roadtrek Motorhomes within 48 hours of
date of retail delivery. When warranty applications are made and Warranty Card is not on file at Roadtrek Motorhomes,
reimbursement of claim will be delayed until proof of original purchase is submitted to Roadtrek Motorhomes.
2. Warranty claims and authorization requests should be submitted using the Electronic Warranty Management system found
on the Dealer Website. Including the last 8 digits of the Vehicle Identification Number (V.I.N.) and odometer reading. All
claims must be submitted within 30 days of the date of repair.
3. Warranty work that will exceed $200 must first be authorized by Roadtrek Motorhomes before proceeding with such work.
The authorization number issued by Roadtrek Motorhomes must be noted on the warranty claim. See item #2 above.
4. Roadtrek Motorhomes reserves the right to inspect defective parts that have been replaced under warranty. Dealer is
expected to hold selected parts for a period of not to exceed 60 days. (See below).
5. Only parts and accessories and other material, available through Roadtrek Motorhomes are to be used in the performance
of warranty service. Express shipping costs are not covered by this warranty policy.
© 2015 by Roadtrek, Inc.
Warranty
79
6. Warranty repairs performed a second time by a Dealer (due to incorrect or inadequate diagnosis, improper assembly or
repair, or lack of proper testing when the original warranty repair was performed) are considered as shop comebacks and
are not reimbursable. Costs of such repairs must be adsorbed by the Dealer.
7. Purchasers are responsible for presenting their motorhome to a Roadtrek Dealer as soon as problem exists. The warranty
repairs should be completed in a reasonable amount of time from date of authorization.
This limited warranty is expressly in lieu of any other expressed or implied warranty, including any implied warranty of
merchantability or fitness for a particular purpose and of any other obligations or liabilities on Roadtrek Motorhomes which
neither assumes nor authorizes any other person to assume for it any other liability in connection with motorhome
manufactured by it.
Appliance Warranty
The following are not initially warranted by Roadtrek Motorhomes, but are covered by individual warranties offered by their
respective manufacturers to which terms both Purchaser and Dealer must comply:
• air conditioner
• electrical inverter/charger
• electronic equipment (TV, DVD player, etc.)
• furnace or other heating system
• microwave oven
• refrigerator
• stove
• toilet
• water pump
• macerator
• water heater.
The 6 year Roadtrek warranty coverage will take over the warranty once the original manufacturer warranties
expire for the remainder of the 6 year period from the date of original purchase.
While still within the terms of the appliance warranty Purchaser and/or Dealer are required to deal directly with the nearest
service center for such manufactured components and abide by the warranty policy as allowed by such component
manufacturers.
© 2015 by Roadtrek, Inc.
Warranty
80
AGM Battery Warranty
Batteries are warranted by the battery manufacturer for one year from the "In Service Date" of the Roadtrek.
1. Warranty is voided if AGM batteries are tampered with, topped off with distilled water or allowed to sulfate or freeze due to
lack of charge.
Diesel Particle Filter Warranty
For diesel vehicles equipped with the underhood generator (GU Option) Roadtrek will warranty the performance of the Diesel
Particle Filter for 6 years. Contact Roadtrek directly for servicing instructions.
Warranty Intent
The intent of this extended warranty is to ensure the new owner of a Roadtrek that it is worry free from manufacturer caused
defects (excluding the chassis) for the first six (6) years of use. Roadtrek owners can feel comfortable that Roadtrek is fully
behind them for six (6) years, including the EcoTrek Batteries!!!
© 2015 by Roadtrek, Inc.
Registration
81
Registration
Please send this form in or email the information to [email protected] [1] when you purchase your Roadtrek.
© 2015 by Roadtrek, Inc.
Registration
82
References
[1] mailto:sales@roadtrek. com
© 2015 by Roadtrek, Inc.
Regulatory Notices
83
Regulatory Notices
If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should
immediately inform the National Highway Traffic Safety Administration, (NHTSA) in addition to notifying Roadtrek
Motorhomes.
If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of
vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems
between you, your dealer, and/or Roadtrek Motor Homes.
To contact NHTSA, you may call the Auto Safety Hotline toll-free at 1-888-327-4236, (or 366-0123 in Washington, DC area) or
write to:
NHTSA
U.S. Department of Transportation
Washington, DC 20590
You can also obtain other information about motor vehicle safety from the Hotline.
© 2015 by Roadtrek, Inc.
HOWTO: Monitor Panel
84
HOWTO: Monitor Panel
The monitor panel is located inside the side door, above the
doorframe. Depending on the options you have, there may be a
gasoline generator starter switch and hour run meter to the
right.
Battery Disconnect Switch
The battery disconnect switch turns the coach battery power off
and on. When off, it prevents your coach batteries from being
drained while the Roadtrek is not in use. The lights, the water
pump, the fan, the refrigerator control board, even the igniters
for the propane cooktop need 12 volt power from the batteries. If
something electrical in your Roadtrek doesn't work, the first
thing to check is to make sure the battery disconnect switch is
on.
The battery disconnect switch is on the bottom left corner of the
monitor panel. To its immediate right is a blue indicator light
which illuminates to show you when the switch is on.
Monitor Panel with standard inverter and optional
gasoline generator
© 2015 by Roadtrek, Inc.
HOWTO: Monitor Panel
Battery disconnect switch
85
Standard inverter switch
You will hear a "clunk" as the battery disconnect switch is pressed - this is a big relay connecting the coach batteries to the
electrical loads.
If you hear a clunk-clunk, or nothing at all, it's possible that your batteries are depleted to the point where they cannot drive
the relay. The best way to charge your batteries in this situation is to start your vehicle engine and try again after it has
charged for a while. Once the relay is working, you can continue to charge with the generator or shore power.
Inverter Switch
Just as the battery disconnect switch powers the lights, fan, and other 12 volt electrical loads, the standard inverter takes 12
volt power from your coach batteries and changes it into 120 volt electricity. It powers some of the smaller 120 volt
alternating current loads, such as the TV and DVD player. This is the regular electricity you have in your house. With this
inverter, you can watch television or play a DVD while you are camping, without the need to plug into shore power or run
your generator.
The inverter is rated for 750 watts maximum output. Larger loads such as the air conditioner or microwave are too big to run
on the power produced by the inverter, and will not operate unless you plug in to shore power or start your generator. The
inverter will shut off if you try to draw too much power through it.
© 2015 by Roadtrek, Inc.
HOWTO: Monitor Panel
86
The inverter switch is on the left side of the monitor panel, above and to the right of the battery disconnect switch. It has an
indicator light inside it that comes on to let you it's on. If you are not using any 120 volt electricity, turn the inverter off to
conserve battery power, since it uses a small amount of electricity even when it's not powering any appliances.
The inverter will also shut off if the battery voltage falls below a certain level. This is to protect your batteries, wiring, and the
inverter itself from damage. Your battery voltage drops under load, so it is possible to have the inverter cut off under high
load when the battery voltage is normal with no load. If this happens, try turning off any power-hungry appliances and trying
again. Things like electric toasters, electric curlers and hair dryers, or anything else that produces heat are usually energy
hogs. Most appliances have the wattage indicated on a label somewhere on the appliance. With practice, you will learn what
you can and can't run within the 750 watt limit.
Inverter Switch With Optional Engine
Generator and 2500 Watt Inverter
Instead of the regular inverter switch on the monitor panel, your
inverter switch will be back in the rear lounge area on the
passenger side, just to the right of the thermostat. The switch
has three positions: off in the middle position, power save auto
in the top position, and power save off in the bottom position.
In the power save auto setting, when you're not using anything
with 120 volt power, the inverter will put itself to sleep. In this
mode, it still uses a small amount of power. If you turn on a 120
volt appliance, it senses a load and will come back on in about
20 seconds. If you select power save auto you'll reduce the
electricity it takes to keep the inverter powered, and your
batteries will require less recharging.
2500 watt inverter switch
The inverter checks for a load by turning on the power
briefly and checking if appliances are connected. This can
cause some appliances, such as the microwave to turn on and off. If this happens, either unplug the appliance or turn
the inverter off or on.
© 2015 by Roadtrek, Inc.
HOWTO: Monitor Panel
87
Pressing the bottom of the switch selects power save off. When this setting is selected, the inverter will be on continuously.
There is a shore power indicator light to the right of the switch to tell you the system is receiving shore power. There is also a
battery charging indicator light to tell you when the batteries are being charged by shore power.
Patio Light
On the monitor panel, the top left switch is the patio light switch. Press the top of the button to turn the lights on, and the
bottom to turn them off. These are LED lights and use very little power.
Patio light switch
Water pump switch on (blue indicator
light lit)
© 2015 by Roadtrek, Inc.
HOWTO: Monitor Panel
88
Water Pump Switch
The centered switch to the right of the leftmost four switches is the water pump switch. It should be on only when you have
water in the fresh water tanks and wish to use the sinks, showers, or toilet. The pump should not be run without water. As
with the patio light switch, pressing the top of the button turns the pump on, and pressing the bottom turns it off.
Water Heater Switch
The water heater switch is to the right of the water pump switch. As with all the other switches on the monitor panel, the
battery disconnect switch must be on for the water heater to work. Even though the water heater uses propane to heat the
water, all the igniters and controls are electrical. Be sure that the water heater is full of water before turning it on - if water
comes out of the hot water faucets when they are opened, the water heater has water in it. After turning it on, the red light to
the right of the switch will come on for a few seconds, than go off as the burner ignites. If the light keeps going off and on,
your burner is not lighting. Make sure that you have propane in your propane tank and that the main valve is open. If the
stove burners light, your propane supply is good.
Water heater switch and red indicator
light
Tank level indicators
© 2015 by Roadtrek, Inc.
HOWTO: Monitor Panel
89
Tank Levels and Battery Charge Indicator
To the right of the monitor panel switches are the indicator lights for the battery charge level, the propane tank level, the
fresh water tank level for each of the two tanks, and the black and gray water tank levels. Press the button for each to see
the display. These will give you an approximate reading, to the nearest third, of how much is in each tank.
Roadtrek recommends that you keep a small amount of water in your gray and black tanks at all times. This will reduce the
likelihood of material sticking to the inside of the tank.
The four indicator lights for the battery are low, fair, good, and charging. Battery voltage dips under load; the greater the load
the greater the voltage dip. A battery under heavy load will show much lower state than one at rest.
The propane indicators will show full when the tank is at it maximum capacity. Because of the safety-related need for a vapor
space at the top of the propane tank, the maximum fill capacity is 80% of the volume of the tank. Your 38 liter/10 gallon
propane tank is full when it holds 30.4 liters/8 gallons of propane. There is another gauge directly on the tank that you can
see behind the propane fill door on the back bumper. This gauge has finer gradations and will give you more information
about your propane level than the indicator light display will.
Generator switch, prime/off position
Generator hour meter
© 2015 by Roadtrek, Inc.
HOWTO: Monitor Panel
90
Optional Gasoline Generator Switch and Hour Meter
To start the generator, first push the bottom of the rocker switch for 5 seconds to PRIME, then push the top of the switch to
START. Allow the generator to run for a couple of minutes before turning on heavy loads such as the air conditioner.
To stop the generator, first shut down all heavy loads, let the generator run for a few minutes to cool down, then press the
STOP (bottom) side of the rocker switch.
The hour meter keeps track of how many hours your generator has been running. This is important for servicing intervals
such as oil changes, etc. See your Cummings/Onan generator service manual for details. There is a break-in oil change after
the first 20 to 50 hours of use. You also need to exercise your generator every month by running it for an hour under
moderate load.
© 2015 by Roadtrek, Inc.
HOWTO: Setting Up Your Campsite
91
HOWTO: Setting Up Your Campsite
What Do You Need To Hook Up?
In a Roadtrek, the answer to this question is - a lot less than you think. Rather than slog through the setup ordeal that Class
As and fifth wheels and other trailers go through, Class Bs are much more nimble. We travel light and can set up and pack up
in minutes. Let's look at the differences in these different types of units and see why.
Most big rigs and trailers don't really have a self-contained
philosophy - they're basically like sticks and bricks homes on
wheels, which require what campgrounds call "full hookups"
(electricity, water, and sewer connections at each campsite) to
function. Roadtreks have big fresh water and holding tanks that
the other types of RVs lack, so it's usually easier just to plug into
the electricity, and not bother with the water and sewer
hookups. This makes your hookup procedure a five minute
process - park in a level spot and plug in. Maybe hook up the
cable TV, too, if they have it at the campsite, but that's about it.
It's a different philosophy because most large RVs plunk down
and don't move once they get to a campsite. They have a towed
vehicle - or the truck they haul their trailer with - to take short
trips around the area. Since you don't have a tow vehicle like
the big rigs, you need to be able to head out to the store or go
sightseeing in your Roadtrek, so the less elaborate the set-up
and pack-up procedures, the better.
Full hookups - electric, water, and sewer - plus lots of
company
© 2015 by Roadtrek, Inc.
HOWTO: Setting Up Your Campsite
92
Connected Fresh Water vs. Using your Tanks
There's no real advantage to leaving the water hooked up all the
time - it's easier just to get your hose out and fill your tanks, and
then put the hose away. No leaks, no hose to trip over, no need
to disassemble and store all that stuff when it's time to hit the
road again. In a campground with shower facilities, your water
supply will last for days, and when it runs out you just get the
hose back out, fill it up again, and you're ready for another few
days.
Sewer Hookup vs. Dumping
The advantage of using your tanks for fresh water over a more
permanent water hookup is that you're automatically reminded
of when your waste water tanks are full. When you're close to
running out of fresh water, that means it's time to dump your
wastewater tanks. With a more permanent hookup, the reminder
Filling your tanks
may be waste water backing up in your sink or toilet, which is
not nearly as pleasant. The tank level indicators only tell you to the nearest third what your tank levels are.
Since you have a waste water discharge pump, the big rig's semi-permanent giant sewer hose on an inclined pathway to the
dump won't work for you - you have to run the pump anyway, so why not just dispense with all that unsightly and potentially
hazardous plumbing? Full hookup sites have a handy sewer dump right at your campsite. When your fresh water runs low,
refill your fresh water tanks, dump your waste water holding tanks, and you're good to go, plus you can drive off anytime
merely by stowing your electrical cord.
© 2015 by Roadtrek, Inc.
HOWTO: Setting Up Your Campsite
93
Simplify, Simplify
Campgrounds capitalize on the helplessness of
non-self-contained RVs by charging a premium for full
hookup sites. You aren't helpless. With an electric-only
hookup, you drive a short distance to the campground's
fresh water source and waste water dump every few
days. Do it on the way to the store or other trip that
you're going to take anyway, and it's no bother. In
addition to saving money, you'll also have a choice of
more campsites, since not all of them have full hookups,
or the even better choice of no campsite at all to take
advantage of the E-Trek's extended boondocking
capability. You can stay out there until you run out of
groceries if you want.
Freedom from hookups also opens up a whole range of
Why drive all the way back to town just to smell someone
national and provincial forest campgrounds with limited
else's woodsmoke? Camp where you are.
or no hookups to you. There is also dispersed camping in
national forests and crown lands and other boondocking
options, where you find your own campsite. There are rules for where you can and can't boondock, so check the forest
websites or drop in at the ranger station for information. Once you're out there, don't look around for those big rigs who are
dependent on hookups - they're all back in town. It's just you and nature, with the occasional backpacker.
© 2015 by Roadtrek, Inc.
HOWTO: Setting Up Your Campsite
94
Leveling your Roadtrek
Roadtreks don't have or need the built-in leveling jacks and stands large
RVs have - it's usually easy enough to move back and forth in your
campsite until you're reasonably level. However, many Roadtrek owners
buy and carry leveling blocks for those places where finding a level spot is
difficult. These are available in most camping supply stores or can be
ordered online. They go under your tires, and can be stacked in various
combinations to lift the low corner or end of your vehicle enough to get
comfortable. Many Roadtrek owners install a small bubble level in an
inconspicuous place visible from the driver's seat to assist with the leveling
process.
How level is level? In general, if it's level enough to be comfortable for you,
it's probably good enough for your plumbing. If you have a choice, it's
better to have the front of the Roadtrek very slightly higher than the back
for air conditioner condensate drainage. If you're not running your air
conditioner, it doesn't matter.
Leveling blocks
© 2015 by Roadtrek, Inc.
HOWTO: Shore Power
95
HOWTO: Shore Power
Connecting To Shore Power
Your Roadtrek has a shore power cord, which is permanently attached inside the rear driver's side compartment, behind the
rear wheel. Open this compartment and pull the cord out to attach to the campsite or house electrical outlet. There is a notch
in the lower right edge of the compartment floor to allow you to feed the cord through and close the storage compartment
door.
Driver's side rear compartment
Cord fed through
"mousehole"
© 2015 by Roadtrek, Inc.
HOWTO: Shore Power
96
Campsite Connections
Most RV parks and campgrounds have AC power of various voltages and amperages available at each site. The power will
typically be in a pedestal with a cover that flips up. If you cannot find your power pedestal or you're not sure how to open it,
ask the campground personnel.
50A outlet
30A outlet
© 2015 by Roadtrek, Inc.
HOWTO: Shore Power
97
15A outlet
Breakers
A typical campsite’s power pedestal will have three types of plug-in receptacles: 15 amp, 30 amp and 50 amp. The 15A
receptacle is typically the same as you would find in your home. The 30A and 50A receptacles are specific to the RV industry.
Other receptacles look similar but may not be wired the same. If in doubt, check with campground personnel.
The pedestal will also typically have individual breakers for the 15A, 30A, and 50A services. Many campgrounds turn off
unused breakers so check that the breaker for the plug you will be using is turned on.
Your Roadtrek is equipped with a 30 Amp cord. Most power pedestals have a 30 amp receptacle.
© 2015 by Roadtrek, Inc.
HOWTO: Shore Power
98
15A to 30A adapter
50A to 30A adapter
It is possible that a campground (or perhaps a friend's driveway) will not have a 30A receptable available for your use. You
can purchase a 15A to 30A adapter and connect to an ordinary 15A household outlet.
Be aware that in those situations, you will have limited power compared to a 30A circuit. You will be able to run a single large
appliance at a time; you may need to turn off your air conditioner if you want to use the microwave, for example.
If you exceed the current capacity of the receptacle you may pop the breakers in the pedestal. If this happens, turn off some
appliances and reset the breaker.
It is also possible that you will find a 50A receptacle. Again, you can purchase a 50A to 30A adapter. In this case your power
should not be limited as you will have the full 30 amps available. Although you are connected to a 50A service, you can only
draw 30A; there is no advantage to connecting to a 50A service if a 30A service is available.
© 2015 by Roadtrek, Inc.
HOWTO: Potable Water Use
99
HOWTO: Potable Water Use
Your Roadtrek can operate in either fully self-contained mode, or can be connected to a water supply such as a campsite's
faucet.
Connecting to a Water Supply
The city water connection is in the driver's side rearmost compartment. Unscrew the white plastic protective cap and connect
your clean hose to the water faucet and this connection point. Turn the faucet on and check for leaks, tightening the
connections as necessary.
Campgrounds and municipalities vary greatly in supplied water pressure. Before connecting to external water
supplies, purchase and install a pressure regulator inline with the water connection.
In a typical campground you may see the faucet with a backflow preventer attached. These look similar to a pressure
regulator but do not affect the pressure. The backflow preventor is there to protect the campground. You need the pressure
regulator to protect yourself from excess pressure.
Backflow preventer
Typical water pressure regulator
© 2015 by Roadtrek, Inc.
HOWTO: Potable Water Use
100
If you have any doubts about a water supply pressure situation, you can always fill your tanks from the water source
using the gravity fill, and use the water pump to supply water from the tanks.
You can connect to a city water connection when your Roadtrek is configured in the summer operation mode. The city water
inlet connection is located in the small compartment just behind the driver's side rear tire.
Roadtrek recommends that you use a potable-water hose. These are usually white in color.
City water fill location
City water valve in closed (handle
vertical) position
Attaching pressure regulator to city
water fill location
To connect the Roadtrek's water system to an outside source:
• Turn the water pump off.
• Close the city water valve by turning the handle to the vertical position.
• Close all interior faucets.
• Flush old water and any contaminants out of the water supply faucet.
• Connect your fresh water hose to the faucet.
• Attach your pressure regulator to the Roadtrek's city water connection.
• Attach a fresh water hose to the the pressure regulator.
• Slowly open the faucet of the city water source.
© 2015 by Roadtrek, Inc.
HOWTO: Potable Water Use
101
• The city water connection by-passes the water pump and
fresh water tank. Therefore, the use of these items is not
necessary when connected directly to an external water
source.
To disconnect the city water connection:
• Turn off the external water source.
• Open a faucet to relieve the pressure in the system. Failure to
do so will not damage your vehicle, but may result in an
unexpected shower when you disconnect the hose. The
outside shower faucet next to the city water connection is a
convenient place to do this.
• Make sure the the city water valve is closed (handle vertical).
• Remove the hose from the city water connection, and replace
the cap on the fill connection.
• Disconnect the hose from the supply faucet and stow it in your
storage compartment. Connecting the ends is a handy way to
prevent dirt or other contaminants from entering the hose
while stored.
Outside shower
If you hear your pump running and water pressure is low inside the vehicle after disconnecting from an external
water source, it is because you have not properly positioned the city water valve. Make sure the black plastic handle is
vertical, and perpendicular to the water line when your water system is in self-contained mode.
© 2015 by Roadtrek, Inc.
HOWTO: Potable Water Use
102
Two-Tank System in Self-Contained Mode
There are two fresh water tanks in your Roadtrek, the internal tank under the passenger side bench, and the external tank
under the driver's seat. Each has its own gravity fill on the rear door passenger side door frame and driver's door frame,
respectively.
Front (exterior) tank gravity fill
Rear (internal) tank gravity fill
There is a manual valve to select which tank your water pump draws water from. There is also a water line connecting the
two tanks with a manual valve on it, so when this line is open water drains from the higher internal tank to the lower external
tank. In non-freezing weather, the easiest way to use the system is to leave the valve on the line connecting the tanks open,
and set the tank selector valve to draw water from the lower external tank. As you use water from this tank, water from the
internal tank replenishes it by gravity, so you can use all of the water from both tanks simply by filling them up and turning
on the water pump.
To access the tank selector valve and the tank isolator valve, open the door on the side of the driver's side bench facing the
aisle, just to the left of the refrigerator. The tank selector valve has a long plastic covered handle, usually either yellow or red.
When this handle is vertical, the tank selector valve is drawing water from the internal tank. You want it to be horizontal and
pointing toward the driver's side of the vehicle - that's the position where it's drawing water from the external tank.
© 2015 by Roadtrek, Inc.
HOWTO: Potable Water Use
Tank selector valve in exterior tank position
103
Tank isolator valve in open position
The tank isolator valve is just a couple of inches to the rear of the vehicle from the tank selector valve (to your left as you
look into this cabinet) and is a smaller black plastic handle on a white water line. You want this handle to be pointed along the
water line (open), not across it (closed). Leave the other two black-handled valves on the left side of this enclosure alone those are the outside shower cutoff valves. Set the tank selector and isolator valves in these positions for warm weather
operation, and simply fill up your tanks when they run out. You don't have to change a thing until you need to operate in
winter mode, or winterize the system. To see how to do that, check out the HOWTO: Summer and Winter Mode and the
HOWTO: Water System Winterizing sections.
If you are driving for extended distances and don't want to carry extra water you don't need (36 gallons of water weighs 300
pounds, and it takes fuel to lug that much weight cross country), just put water in the front (exterior) tank at the driver's door
gravity fill, and leave the back (interior) tank empty. You will still have 20 gallons or so of water for use, and will travel lighter
with a better weight distribution since your rear axle will be about 85 pounds lighter. Every little bit helps. Of course, once
you get to the area where you're going to camp, fill up both tanks before you head out boondocking so you can stay out for a
longer time without running out of water.
© 2015 by Roadtrek, Inc.
HOWTO: Waste Water Dumping
104
HOWTO: Waste Water Dumping
Wastewater storage and dumping
Your house is permanently connected to your septic system or a municipal sewer; you don't have to worry about the
wastewater you generate because gravity takes it away. Your Roadtrek doesn't have that connection, and has to hold any
wastewater until you have the opportunity to dump it at an approved dump station.
Most municipalities have severe penalties for improper disposal of human waste, especially into a watershed - fines
can be several thousand dollars, and it's often a felony. Even if it's "just gray water", it will still flunk a coliform bacteria
test because of the common discharge hose, which is difficult to explain to a judge. Never dispose of wastewater unless
you're sure you are at an approved dump station.
Tanks
Your vehicle is equipped with a gray holding tank and a black holding tank. The gray tank holds the sink and shower water.
The black tank holds the toilet waste. As a result the black tank is a lot nastier than the gray tank.
Waste Water Discharge Pump
Your Roadtrek is equipped with a waste water disposal pump to make dumping your tanks easier and cleaner. The macerator
in this pump grinds up any solids in the system and pumps the resulting wastewater out to the dump station.
Do not throw any paper towels, personal wipes, rags, baby wipes, tampons, hairballs, etc. into the toilet. The
macerator is not capable of handling these types of solids and will jam or be damaged. Use toilet paper intended for RVs
or septic systems.
If in doubt, take a tissue, and leave it in a glass of water. Stir with a spoon a couple of times. If it falls apart into a
gooey slurry after a few minutes it`s safe for your tank. If it stays together, swells up, or clumps into a solid mass, it`s
not safe and should be disposed of in the trash and not down the toilet.
© 2015 by Roadtrek, Inc.
HOWTO: Waste Water Dumping
105
If possible, you want to dump the tanks after driving as the movement of the vehicle will have sloshed the water in
the tanks, loosening any solids.
Make sure the tanks are as full as possible before dumping - you may wish to use a hose or bucket to add water to
the black water tank through the toilet if it is less than 1/2 full.
You should dump the black tank first, then the gray tank. The water in the gray tank is considerably cleaner, and will
rinse any remaining solids from the hose and the macerator. You should dump both tanks in sequence if possible.
Dumping the tanks
Sprinter side compartments
210 Popular side compartment
• Open the compartment doors or drawer behind the driver. This will expose the green waste water discharge hose and
controls.
Depending on your model, your hose and dump valve location may look a bit different. Take the time to identify all of
the components before you start.
© 2015 by Roadtrek, Inc.
HOWTO: Waste Water Dumping
106
• Open the driver’s door and locate the waste water pump switch. It is a red pushbutton located on the driver's seat base or
on the B pillar.
Macerator button on base of driver's seat
Macerator button on the B pillar behind
driver
• Remove the waste water discharge hose from storage by pulling it straight out far enough to reach the dump.
• Insert the waste water discharge hose outlet into the dump station waste receptacle.
• Open the valve on the end of the sewage discharge hose by turning the black plastic handle to align with the hose.
© 2015 by Roadtrek, Inc.
HOWTO: Waste Water Dumping
Extending the hose
107
Open the dump hose valve
• There are two ways to secure the hose in the dump station waste receptacle four inch pipe. In the white box that came
with your Roadtrek there is a rubber doughnut, which goes over the discharge nozzle and can be wedged into the waste
receptacle to hold the waste water discharge hose in place. Some RV parks require you to use a doughnut. If you trust
gravity more than friction, or don't want to store the doughnut between uses, use a rock to weight the hose down. Either
way, make sure the hose doesn't get loose when you turn the pump on.
The discharge stream is forceful and will knock the hose out of the drain if you do not weight it down or secure it in
the drain with the doughnut. It is much easier and more sanitary to secure it before turning the pump on than it is to
chase it around afterwards.
© 2015 by Roadtrek, Inc.
HOWTO: Waste Water Dumping
Rubber doughnut installed on nozzle
108
Rock used as weight to hold the hose
• Push the jogger handle in and turn it to loosen any materials in the macerator. Pull the jogger handle out.
• Open the black water tank gate valve by pulling the black handle out. It will come out approximately three inches (8 cm)
and stop.
• Press and hold the waste water pump button until the tank is empty.
• Close the black water tank valve by pushing in on the handle.
• Open the grey water tank gate valve by pulling the grey handle out. It will come out approximately 1 1/2 inches (4 cm) and
stop.
• Press and hold the waste water pump red button until the grey waste tank is empty.
• Close the gray tank valve by pushing it back in to the original position.
© 2015 by Roadtrek, Inc.
HOWTO: Waste Water Dumping
Open the black valve
109
Open the gray valve
Always dump the black tank first and the gray tank second. The graywater will help flush any remaining solids from
the dump hose. If you wish to rinse the system, pour water down the toilet and sink, and dump again.
• Close the discharge valve on the end of the waste water hose.
• Rinse off the dump area and the dump hose.
• Return the waste water hose to its storage compartment by pushing the green hose back onto the reel.
• Add about ½ gallon of fresh water to the black tank. While you`re doing this, add a packet of black holding tank chemicals
to the tank.
Do not toss the packet into the toilet, even if it claims to be `dissolvable`. It may not be dissolvable enough for the
macerator. Tear open the packet and pour the contents into the black tank, and dispose of the packet in the trash. The
contents of the powder packets can be irritating to your eyes and nose, so hold the packet low to the bowl and try to
pour directly into the tank.
The waste water discharge pump will be damaged if allowed to operate dry for any length of time. Turn off the pump
as soon as the solid stream of liquid begins to sputter, and the pump's sound changes.
© 2015 by Roadtrek, Inc.
HOWTO: Waste Water Dumping
110
Jammed waste water pump
Sprinter macerator manual crank knob
Chevy macerator
manual crank knob
If the waste water discharge pump stops while you are pushing the button, it's jammed. Something has gotten caught up in
the blades. Release the button to stop the pump.
• Locate the manual waste water pump knob.
• Push in on the knob and turn clockwise; you will feel the knob engage the pump shaft.
• Turn the knob first in one direction and then the other to loosen the obstruction.
• Once the obstruction is loose, continue dumping.
© 2015 by Roadtrek, Inc.
HOWTO: Cable and TV Reception
111
HOWTO: Cable and TV Reception
Your Roadtrek comes with a home theatre system. This consists of a TV, a DVD player, the speaker system and the radio in
the dash, along with a rooftop TV antenna and a cable TV connection.
The TV and home theatre system are located in the rear on the passenger side. The Cable TV/Antenna switch and power
injector for the built-in antenna are in the cabinet just above the DVD player.
The TV and the home theatre system must be on to use the system. Both the television and the DVD player use 120 volt
current, so the inverter, generator, or shore power must be used. Refer to the Electrical System for instructions on 120 volt
AC power.
The TV and DVD are supplied with remote controls.
The home theatre system has inputs for media devices. Read the Owner's manual for full details.
TV Bracket release
DVD player
The TV is stowed against the wall on a hinged bracket. The bracket is secured with a large thumbscrew. Turn the thumbscrew
horizontally to release the bracket and vertically to secure the bracket to the wall.
Once released, you can swing the TV to a comfortable viewing position.
Always stow the TV with the bracket secured to the wall for travel.
© 2015 by Roadtrek, Inc.
HOWTO: Cable and TV Reception
TV antenna switch and power injector
112
Rear speaker switch
Over-the-air TV
To watch TV using the Roadtrek rooftop antenna:
• Have 120 volt AC power available (inverter on OR shore power plugged in OR generator running)
• Turn on TV and home theatre system
• Make sure the power injector is on (the barrel connector is plugged into the top of the injector)
• Set the speaker selector to "SURROUND"
• Set the antenna/cable TV switch to Antenna
© 2015 by Roadtrek, Inc.
HOWTO: Cable and TV Reception
113
DVD
To watch a DVD:
• Have 120 volt AC power available (inverter on OR shore power plugged in OR generator running)
• Turn on TV and home theatre system
• Set the speaker selector to "SURROUND"
Cable TV
To connect your Roadtrek to cable TV at a campsite or even in your driveway, first locate the Roadtrek's cable TV connection
inside the rearmost driver's side compartment, behind the rear wheel. It has a square gray plastic cover about 3 cm on each
side which is hinged at the top, and opens to expose the barrel connector the cable hooks to.
You need a length of coaxial TV cable to reach from the cable TV outlet to your Roadtrek's connection point. These are sold in
electronic supply and camping supply stores and come in lengths of 25, 50, and 100 feet. The cable is typically sold as
RG-59U or RG-6 with F-type connectors. The RG-6 is preferable but either will work.
TV cable connected
Push the small button
to select Antenna or
Cable
© 2015 by Roadtrek, Inc.
HOWTO: Cable and TV Reception
114
Screw the cable onto the barrel connectors at each end. If you route it through the "mousehole" in the bottom right side of
the compartment floor, you can close the compartment door without crimping the wire.
Push the bottom button on the A-B switch in the cabinet above the TV. The bottom button connects your TV to the cable
connection, and the top button connects it to the over-the-air signals from your rooftop antenna.
Speaker Switch
The speaker switch is located in the same cabinet as the
Cable/Antenna switch. You can select Surround, Off, or
Automotive.
In the Surround position, the rear speakers (the speakers above
the bed) will work with the TV/home theatre system. In the Off
position the speakers are off. In the Automotive position, the
speakers are connected to the dash radio.
Rear speaker switch
© 2015 by Roadtrek, Inc.
HOWTO: Propane System
115
HOWTO: Propane System
1. REDIRECT HOWTO: Propane System/All
© 2015 by Roadtrek, Inc.
HOWTO: Summer and Winter Mode
116
HOWTO: Summer and Winter Mode
Summer and Winter Mode
The 190 and 210 Popular models have the capability to operate in mildly sub-freezing conditions, provided the water system
is properly configured. To better understand this it is best to know how the plumbing is configured. The diagrams below show
how water is supplied in each mode. Solid triangles are closed valves; hollow triangles are open valves.
Fresh water system in summer
mode
Fresh water system in winter
mode
In summer mode, both fresh water tanks are in use. The interior tank is inside the vehicle and is filled via the gravity fill in the
back door frame, and the exterior tank is below the vehicle, and filled via the gravity fill in the driver's door post. The water
line between the two is open, so water flows from the higher interior tank to the lower exterior tank as the water pump draws
water from the exterior tank.
In winter mode, the line between the two tanks is closed, and the exterior tank is drained to prevent it from freezing. The
outside shower water lines are closed and drained to prevent them from freezing, and the water pump draws water from the
interior tank, which is protected from freezing by cabin heat. The hot water heater will also not freeze if left running. In this
way, hot and cold running water continues to be supplied to the galley sink, toilet, and shower.
© 2015 by Roadtrek, Inc.
HOWTO: Summer and Winter Mode
117
"Winter mode" and "winterized" are two different things. Winter mode protects the water in the system from mildly
sub-freezing conditions as long as the Roadtrek is adequately heated and in use. If you plan extended stays in
sub-freezing conditions or if you store your vehicle in freezing conditions, you must winterize to avoid damage to the
water system. To prepare your vehicle for really cold weather, see HOWTO: Water System Winterizing
• Open the lid on the side bench enclosure by removing the side bench's cushion and table to expose the hinged lid. Undo
the Robertson head screw to raise the lid. Once you know where these valves are you can just open the access door on the
front, but it's best to unscrew the top to give you a full view if you're not familiar with these controls.
Screw to open water valve enclosure
Lid raised to expose valves and water
pump
© 2015 by Roadtrek, Inc.
HOWTO: Summer and Winter Mode
118
Switching from Summer to Winter Mode
• Open the enclosure under the driver's side bench just to the left of the refrigerator, and close the tank isolator valve
connecting the two fresh water tanks by turning the black plastic handle so that the handle is across (perpendicular to) the
water line, pointing toward the rear of the vehicle.
• Drain the exterior tank by opening the valve under the driver's door step. The valve is open when the black plastic handle
is aligned with the water line. It may take several minutes for the water to drain out.
Tank isolator valve in closed position
(black plastic handle pointed toward the
back of the vehicle). This valve is located
inside the enclosure, under the driver's
side bench.
Exterior tank drain, located under the
driver's door step. To open the valve and
drain the tank, turn the handle so that it
points along the water line.
• Run the water pump briefly to drain water from the water line to the exterior tank, then switch the tank selector valve from
the exterior to the interior tank.
© 2015 by Roadtrek, Inc.
HOWTO: Summer and Winter Mode
Tank selector valve in exterior tank position
(colored plastic handle pointed toward driver's
side of Roadtrek). Tank isolator valve is open,
allowing water to draing from interior tank to
exterior tank.
119
Tank selector valve in interior tank position,
with the colored plastic handle pointed up.
Tank isolator valve is closed, preventing water
from flowing into the exterior tank.
• Close the two shutoff valves going to the outside shower faucet. These valves are visible through an access hole in the
enclosure floor just to the rear of the other valves. To shut these valves, turn them so that the black plastic handles are
across the water line.
© 2015 by Roadtrek, Inc.
HOWTO: Summer and Winter Mode
Outside shower valves, shown closed
120
Outside shower valves, shown open
• Open the outside shower faucets to drain the water from the lines. There will be no water pressure; just let the small
amount of water remaining in the lines dribble out. Leave these faucets open.
In winter mode, remember that you need to keep the interior temperature at least 60 degrees F (15 C) by running the
propane furnace or heat pump, and keep the water heater running. Also remember that the waste water tanks are not
protected from freezing. If you use them, mix pink RV antifreeze with whatever you put down the drain 50/50. If you do not
use them, drain and winterize the waste water system.
Switching from Winter to Summer Mode
• Check to be sure the exterior tank drain valve under the driver's door step is closed, and fill the exterior tank using the
gravity fill on the driver's door post.
• Open the tank isolator valve to connect the two tanks. In winter mode the handle is across the line - turn it so that the
handle points along the line.
© 2015 by Roadtrek, Inc.
HOWTO: Summer and Winter Mode
Tank isolator valve in open position
(black plastic handle pointed along line).
This valve is located inside the water
control enclosure under the driver's side
bench to the left of the refrigerator.
121
Exterior tank drain, located under the
driver's door step. To open the valve and
drain the tank, turn the handle so that it
points along the water line.
• Switch the tank selector valve from the interior to the exterior tank by moving it from the vertical position to a horizontal
one pointing toward the driver's side of the vehicle.
© 2015 by Roadtrek, Inc.
HOWTO: Summer and Winter Mode
Tank selector valve on the left in closed or
interior position. Tank selector valve on the
right in interior tank position, with the colored
plastic handle pointed up.
122
Tank isolator valve on the left in open or
exterior position. Tank selector valve on the
right in exterior tank position (colored plastic
handle pointed to the driver's side of the
Roadtrek).
• Open the two shutoff valves going to the outside shower by placing the handles parallel to the water lines, and close the
outside shower faucet after running water through them briefly to flush air and any contaminants.
© 2015 by Roadtrek, Inc.
HOWTO: Summer and Winter Mode
Outside shower valves, shown closed
123
Outside shower valves, shown open
© 2015 by Roadtrek, Inc.
HOWTO: Water System Winterizing
124
HOWTO: Water System Winterizing
Do you really need to winterize?
If your Roadtrek is going to remain heated to comfortable temperatures, and the temperatures during the day are
well above freezing (above 40 deg. F or above 4 deg. C) and the forecast is for temperatures just below freezing for a
few hours at night with calm winds, then you don`t need to winterize. The heat in your Roadtrek is enough to keep the
lines from freezing.
If the forecast is for extended cold periods, with daytime temperatures at or below freezing, if you`re not heating
your Roadtrek, or if you expect sustained winds and the roads and ground is already frozen, you need to winterize.
As always, you are final judge and you need to do what is comfortable and makes you feel good. If you are not
comfortable with leaving water in your lines when it gets cold, and you will sleep better, go ahead and winterize.
© 2015 by Roadtrek, Inc.
HOWTO: Water System Winterizing
125
How to winterize using anti-freeze
Typical non-toxic RV
antifreeze
Water valves enclosure
This procedure can be done in less an hour with only one specialized tool, a 1-1/16 inch (27 mm) socket and a ratchet or
breaker bar.
• Get 2-3 gallons of RV antifreeze.
DO NOT use automotive antifreeze. It is toxic. RV antifreeze is non-toxic and safe for potable water lines.
• Dump and rinse the gray and black tanks if they are not already empty.
• Turn off the water pump and open your single lever galley faucet, putting it in the middle halfway between the hot and cold
settings.
© 2015 by Roadtrek, Inc.
HOWTO: Water System Winterizing
Location of the tank isolator valve shown
in the open (i.e. tanks connected)
position; note valve is in-line with pipe
126
Freshwater tank drain valve, shown
closed
• Drain the fresh water tanks by opening the black tank isolator valve on the water line connecting the two fresh water tanks
(in the water valve enclosure under the diver's side bench, on the floor), and opening the drain for the exterior tank under
the driver's door. Let this drain for at least 30 minutes. Close the valve between the tanks and the drain for the exterior
tank.
© 2015 by Roadtrek, Inc.
HOWTO: Water System Winterizing
Tank selector lever in the interior (vertical)
position
127
Tank selector lever in the exterior (horizontal)
position
• Switch the plastic covered tank selector lever to the interior tank position (handle vertical), and turn the water pump back
on. Put the galley faucet in the cold position, and open it. If the interior tank is empty, the open galley sink faucet should
sputter. If it emits a steady stream of water, the tank is not empty. You will need to run the water until it is empty, either
catching it in a container and throwing it outside, or running it down the sink and re-dumping the gray water tank. Do so if
necessary, and then turn the water pump off. Return the galley sink lever to its open position halfway between hot and
cold.
© 2015 by Roadtrek, Inc.
HOWTO: Water System Winterizing
Water heater cover removal (turn tab
vertically to remove cover)
128
Water heater pressure relief valve
• Make sure the water heater is turned off on the monitor panel switch. Go outside and take the cover off the water heater.
Pop open the pressure relief valve at the top of the water heater. A small amount of water might flow out.
If water is gushing out continuously, STOP! Go back to the beginning of this guide. DO NOT remove the anode rod
until you figure out what`s going on. You either left the water pump on, or you are hooked up to city water.
© 2015 by Roadtrek, Inc.
HOWTO: Water System Winterizing
Water Heater Anode
129
Water heater anode with some corrosion,
but probably cleanable and usable for
another year.
• Drain the water heater by removing the anode rod. You will need a 1-1/16” socket and a ratchet or breaker bar.
This is a good time to rinse out the water heater and inspect the anode rod. If the anode rod looks spongy or all that
is left is a rusty iron rod, throw it away and buy and install a new anode rod. Use teflon tape on the threads to reinstall
the anode rod. Do not overtighten.
© 2015 by Roadtrek, Inc.
HOWTO: Water System Winterizing
Water heater bypass valves in the
unwinterized, normal position
130
Water heater bypass valves in the bypass
position
• The water heater bypass valves are in the cabinet under the sink, on the left wall. Set the valves to the by-pass position
(see photo). The “middle valve” (the one on the horizontal water line connecting the two vertical lines) should be turned in
line with the tubing. All handles should have been pointing vertically in the normal, summer use position. Turn each handle
90 degrees to a horizontal position to achieve the bypass position.
• Check to be sure that the fresh water drain on the exterior tank and the black and and gray tank valves are all closed.
Move the single lever galley faucet all the way to the cold side, and leave it open.
• Add 1 1/2 gallons of non-toxic RV approved antifreeze to the interior tank, and 1/2 gallon to the exterior tank through the
gravity fill. Use a funnel and wash any spillage off the paint. Put the tank selector switch in the exterior tank position
(handle horizontal, pointed toward driver's side of vehicle).
• Turn the water pump on and allow to prime. Close cold galley sink faucet once you see pink antifreeze coming out. Switch
the plastic covered tank selector handle to the interior tank position.
• Move the single lever galley faucet to the hot side, and run until you see pink antifreeze come out. Open both hot and cold
faucets in the bathroom sink. Open the toilet valve. Open the hot and cold faucets on the outside shower. Leave the
outside shower valves open, or open them if you were in winter mode. Observe the antifreeze flow through all fixtures,
then close each fixture. Ensure antifreeze flows into all P-traps (galley sink, washroom sink, and shower). You may also
consider adding antifreeze from the extra gallon in the container jug to the shower floor-pan trap.
© 2015 by Roadtrek, Inc.
HOWTO: Water System Winterizing
Valves for outside shower lines, shown
open
131
Valves for outside shower lines, shown
closed
• If the water pump loses its prime in this process, add more antifreeze to the interior fresh water tank.
• Open the grey and black waste tank valves, and operate the waste water discharge pump for about 10 seconds. You should
see pink antifreeze coming out of the waste water discharge hose.
© 2015 by Roadtrek, Inc.
HOWTO: Water System Winterizing
City water connection valve, shown
closed
132
Water pump filter, inside water heater
enclosure
• Turn the city water connection valve on. The water pump will operate. Allow it to run about 20 seconds. Turn city water
connection valve off.
• Turn the water pump off and open a galley sink faucet to release back pressure.
• Open the valve on the water line connecting the two fresh water tanks (in the water heater compartment on the floor, left
side, at the base of the large speaker) to allow the remaining antifreeze in the interior tank to drain into the exterior tank.
• Open the fresh tank drain line briefly until antifreeze flows out.
• Remove water pump filter if so equipped. Replace water pump filter lid.
Winterizing using compressed air
Roadtrek recommends against using compressed air for winterizing.
Other methods of winterizing
Roadtrek only recommends the winterizing method outlined above using RV antifreeze.
© 2015 by Roadtrek, Inc.
HOWTO: De-Winterizing
133
HOWTO: De-Winterizing
If you winterized only for a short time (less than a week) you can skip to the second step.
First step
You will need 4 gallons of water and 2 cups of fresh bleach. (Bleach loses its potency over time; always start with bleach that
is less than 6 months old.)
1. Close the connecting valve between interior and exterior tanks. This valve is located under the drivers side bench seat
inside the water valve enclosure.
Valve connecting the interior and exterior
tank, shown closed
Exterior tank drain, under driver's door
step
1. Mix up two gallons of water and one cup of chlorine bleach. Add to the interior tank fresh water fill on the right rear door
doorpost.
2. Mix up two gallons of water and one cup of chlorine bleach. Add to the exterior fresh water fill, the one on the driver's
doorpost. You now have a chlorine mixture in both water tanks.
© 2015 by Roadtrek, Inc.
HOWTO: De-Winterizing
134
3. This is a good time to get some stuff for spring cleaning of your Roadtrek, so drive around for an hour. Let it sit for a
couple more hours.
4. Open the connecting valve to the exterior tank and let mixture drain into that tank.
5. Open the exterior tank drain valve and drain both tanks. This can take an hour or so. You can speed up the process by
putting the tank selector valve on the interior tank, turning the water pump on, and opening the outside shower faucet until
no more water comes out. Close the faucet and turn the water pump off.
This kills any bacteria in the tanks before you distribute them through the entire water system.
Second step
You will need a good supply of fresh water and a cup of chlorine bleach.
• Close the connecting valve.
• Fill the exterior fresh water tank approximately 1/2 full, adding a cup of chlorine bleach halfway through the filling process.
Filling the exterior tank
Tank isolation valve on the left in open
or connected postion; tank selection
valve on the right in exterior tank
position
City water valve in closed position
• Put the plastic covered tank selector handle in the exterior tank position (pointed toward the driver's side of the vehicle).
Turn on the water pump, and circulate the dilute bleach solution through the entire system. The water heater is still
© 2015 by Roadtrek, Inc.
HOWTO: De-Winterizing
135
winterized. Run water out of all three faucets (galley, washroom, and outside shower), hot and cold, until you smell
chlorine. With the water pump on, open the city water valve and let the pump push water through the fill line for a minute
or so. Close the city water valve.
• Pull the anode rod out of the water heater and flush out the water heater tank with a hose. Install the new anode rod using
Teflon tape on the threads, and close the pressure relief valve. Take the system out of water heater bypass mode by
turning the three valves on the lines in front of the water heater so that the handles all point vertically.
Anode rod location
Water heater bypass valves in normal
position - all handles vertical
• Open the galley sink, move the handle in the hot water direction, and run the water pump until water flows from hot water
tap at sink and you smell chlorine. The water heater holds six gallons, so it will take a while for it to fill up.
• Allow the system to sit overnight.
• Drain both tanks completely, fill both fresh water tanks with clean water, and run all faucets for 2-3 minutes each. To help
get rid of the residual chlorine smell, pour a half cup of vinegar into each tank, fill, let sit for a few hours, drain, and refill
with fresh water.
© 2015 by Roadtrek, Inc.
">