Safety Instructions
Disclaimer
WARNING
NOTES
Attention
What's in the Box
Anker SOLIX Home Power Panel
12-Circuit Backup Load Center (Optional)
What You Need
Product Overview
LED Indicators
Pre-Installation
System Overview
Installation Scenarios
Installation
Install the Anker SOLIX Home Power Panel.
Install the 12-Circuit Backup Load Center (Optional)
Electrical Connections
Wiring to Home Main Panel
Wiring to 12-Circuit Backup Load Center (Optional)
Checking Connection
Completing Installation
Reinstall the Panels
Connect to Anker SOLIX F3800 Portable Power Station
Turning On Anker SOLIX Home Power Panel
Starting to Use Your Anker SOLIX Home Power Panel
The Anker App for Smart Control
Specifications
Customer Service
Safety Instructions
Disclaimer
Before using this product, please read this user manual thoroughly to ensure you fully understand its contents. Retain this user manual for future reference.
In this manual and any associated documents, specific terms may be abbreviated or referred to by acronyms for ease of reference. Improper operation of
the product could result in serious injury to the user or others, as well as damage to the product or other property.
By utilizing this product, you acknowledge and agree that you have read, understood, and accepted all terms and conditions outlined in this document.
Users are solely responsible for their actions and the consequences thereof. Anker expressly disclaims any liability for losses or damages that may arise
from the user's failure to operate the product in accordance with the instructions provided in the User Manual.
In accordance with applicable laws and regulations, Anker reserves the right to the final interpretation of this document and all related documents pertaining
to the product. The contents of this document are subject to change (including updates, revisions, or discontinuation) without prior notice. For the most
recent product information, please visit Anker's official website.
WARNING
1. Please read the instructions in this safety manual carefully before installing, using, and maintaining this product. Anker is not responsible for any problems
caused by improper conduct during installation and maintenance procedures.
2.When using this product, please ensure you strictly follow the ambient temperature range specified in this user guide.
3.Use appropriate personal protective equipment (PPE) and follow safe electrical work practices.
4.Anker SOLIX Home Power Panel is designed for indoor use. Make sure the product is installed in a dry and ventilated location.
5.Installation personnel need to wear insulating gloves, safety glasses, and rubber-soled shoes. Turn off the main circuit and solar breakers before
conducting any setup or maintenance.
6.Ensure that circuit breakers of the entire system are off during the wiring process.
7.To protect the wires and ensure electrical safety, users need to purchase and install waterproof conduits with appropriate wire lengths.
8.Please make sure to use a bolt to secure the hole in the middle of the breaker.
9.To ensure electrical safety and extend the service life of electrical appliances, never plug or unplug wires while the power supply is on.
10.Make sure to connect live and neutral conductors to the Backup Load Center.
11. Before connecting Anker SOLIX F3800, make sure the circuit breaker for the entire system is off.
12.When using Anker SOLIX F3800 Portable Power Station for the first time, please ensure its power is below 95% to ensure that the system starts the
self-test successfully.
13.When conducting repairs, first turn off Anker SOLIX Home Power Panel, followed by turning off the emergency stop, Breaker 1, and Breaker 2. Their
power buttons are located on the side.
14.Keep this product out of reach of children and pets. Be extra vigilant about potential dangers when children or pets get close to the device.
15.Do not disassemble, modify or replace this equipment (including internal and external components). If necessary, please contact qualified professionals
or the Anker After-Sales Service Department for handling.
16.Avoid impacts, falls, drops, or strong vibrations. In case of severe external shock, turn off the power immediately and stop using the product. Ensure that
the product is firmly fixed during transport to avoid vibration and shock.
17. Do not stand, tilt, or sit on the product.
18.Do not connect this device with damaged cables. The use of damaged cables may affect the normal operation of the device or lead to potential risks.
19.Do not insert hands or foreign objects into the ports or ventilation openings.
20.If the product accidentally falls into water during use, place it in a safe open area until completely dry. Dry products should not be reused and should be
handled correctly according to the "Handling" section below. If the product catches fire, please use fire extinguishers or extinguishing equipment in the
following recommended order: water or mist, sand, fire blanket, dry powder, and carbon dioxide fire extinguishers.
21.Handle this product with care to prevent damage from tipping. If the product is seriously damaged when tipped over, turn off the power immediately,
place the battery in an open area away from flammable materials or people, and dispose of it appropriately in accordance with local laws and
regulations.
22.The electromagnetic field generated by this product may affect the normal function of medical implants or personal medical equipment, such as
pacemakers, cochlear implants, hearing aids, defibrillators, etc. If you are using these medical devices, please consult the medical device manufacturer
regarding restrictions on the use of relevant devices to ensure a safe distance between this product and implanted medical devices (such as
pacemakers, cochlear implants, hearing aids, defibrillators, etc.).
23. After installation, promptly clean up cardboard boxes, foam, plastic, etc.
NOTES
1. The four indicators run from right to left if the device is in firmware upgrade status.
2.Only Backup mode requires the 12-Circuit Backup Load Center.
3.Keep a clear space of 3 ft in front of the main panel for workspace.
4.If a solar power system is connected to your home's main panel, the 100A current transformer can be clamped on the wire connected to the solar panel.
5.When Anker SOLIX Home Power Panel is connected to two Anker SOLIX F3800 Portable Power Stations, connect an equal number of expansion batteries
to each Anker SOLIX F3800 Portable Power Station.
Attention
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS – This manual contains important instructions for Anker SOLIX Home Power Panel.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Compliance Statement
This equipment complies with the FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated
with a minimum distance of 20 cm between the radiator and your body.
The following importer is the responsible party.
Company Name: Fantasia Trading LLC
Address: 5350 Ontario Mills Pkwy, Suite 100, Ontario, CA 91764
Telephone: +1-800-988-7973
What's in the Box
Anker SOLIX Home Power Panel
Anker SOLIX Home Power
Panel
F3800 to Home Power
Panel Cable (1.5m)
(×1)
Backplate Bracket
(×2)
Wall Bracket
(×2)
200A Current Transformer 100A Current Transformer
(Model: XH-SCT-S24) (Model: CTSA016-100A/100mA)
(Accuracy: 0.5%)
(Accuracy: 0.5%)
(Specification: Max 300A,
(Specification: Max 120,
250VAC,200A/66.6mA,
250VAC,100A / 100mA,
50/60Hz)
50/60Hz)
(×2)
(×1)
M6*50 Hexagonal SelfTapping
M6*60 Expansion Bolt
(Secures Wall Bracket to (Secures Screw
Wall Bracket to
Concrete Wall)
Wooden Wall)
(×4)
(×4)
M4*10 Cross Recessed
Countersink
Screw (6 screws to secure
Backplate Brackets to Home
Power Panel, 4 screws to
secure Wall Bracket to
Backplate Bracket)
(×10)
Installation Guide
Positioning Card
12-Circuit Backup Load Center (Optional)
12-Circuit Backup Load
Center
(×1)
What You Need
100A Circuit Breaker
(×1)
12-Circuit Backup Load
Center Ground Bar Kit
(×1)
Waterproof Conduits
Connector
Condulet
OT / Ring Terminal
Connectors
Cables
(Please purchase
according to the table
below.)
M6*50 Hexagonal SelfTapping Screw
( Secures 12-Circuit
Backup Load Center)
(×10)
Cable
Color
L1
L2
Single
F3800
System
Grid
(Connect to Main
N
Panel)
GND
L1
Backup
(Connect to 12- L2
Circuit Backup
Load Center) N
GND
Black
Red
White
Current
50A Max
Gauge
6 AWG
6 AWG
6 AWG
Green and Yellow
10 AWG
Black
10 AWG
Red
White
25A Max
10 AWG
10 AWG
Green and Yellow
10 AWG
L1
Black
3 AWG
L2
Grid
(Connect to Main
Panel)
N
Red
GND
White
Green and Yellow
L1
Black
Backup
L2
(Connect to 12Circuit Backup N
Load Center)
GND
Red
Parallel
F3800
System
Product Overview
White
Green and Yellow
75A Max
3 AWG
3 AWG
8 AWG
6 AWG
50A Max
Material
6 AWG
6 AWG
10 AWG
Copper
On/Off Button
To Power On/Off: Press for 2 seconds.
This button can be used to turn on the Bluetooth hotspot.
Grid Indicator
Power Station 1 Indicator
Power Station 2 Indicator
Backup Load Indicator
Grid Wiring Area
Backup Wiring Area
CT Port
Emergency Stop
In case of emergency and product maintenance, this button can be manually turned on to cut off the power of the entire system immediately.
Reset
Inserting into this hole can reset the device to factory settings.
Breaker 2
It can be manually or automatically turned on (under overload or short circuit conditions) to interrupt the current of Power Station 2, preventing further
damage to the circuit.
Breaker 1
It can be manually or automatically turned on (under overload or short circuit conditions) to interrupt the current of Power Station 1, preventing further
damage to the circuit.
Wiring Hole
The diameter of the side wiring hole is 1.73 in / 44 mm.
The diameter of the bottom wiring hole is 1.33 in / 33.8 mm.
Power Station Ports
The ports can be used to connect the power station and Home Power Panel
Antenna
To ensure clear communication signals, please extend the antenna of Home Power Panel.
LED Indicators
Indicator
On/Off
Grid Indicator
Power Station 1 / 2
Indicators
Status
Description
Steady White
Operating Normally
Flashing White
Product Malfunction
Quickly
Flashing White Slowly System Test Incomplete
Off
Anker SOLIX Home Power Panel is Powered Off
Steady White
Wi-Fi / Bluetooth Connection Successful
Flashing White
Pairing
Off
Deactivated
Steady White
Anker SOLIX Home Power Panel Powered from Grid
Steady White
Power Station Connected with Anker SOLIX Home
Power Panel
Flashing White
Device Connection Malfunction
Off
Power Station Not Connected with Anker SOLIX Home
Backup Load Indicator
Pre-Installation
Steady White
Power Panel
Anker SOLIX Home Power Panel is Supplying Power to
Home Loads
System Overview
Installation Scenarios
1. Turn off the breakers.
Remove the wiring compartment cover of the Home Main Panel. Turn off the main circuit breaker and solar breaker.
2. If your Home Main Panel is indoors.
If the Home Main Panel is indoors, please refer to the distance requirements in the picture. The 12-Circuit Backup Load Center should be at least 5 in / 127
mm above Anker SOLIX Home Power Panel.
3. If your Home Main Panel is outdoors.
If the Home Main Panel is outdoors, we recommend the distance between the Home Main Panel and Anker SOLIX Home Power Panel is no more than 16 ft
/ 5 m. To facilitate the transfer of backup loads to 12-Circuit Backup Load Center, we suggest the 12-Circuit Backup Load Center be installed next to the
Home Main Panel.
Note: The following instructions will assume you have an indoor Home Main Panel.
Installation
Install the Anker SOLIX Home Power Panel.
1. Reserve at least 5 in / 127 mm of space next to the Home Main Panel and mark the position of Anker SOLIX Home Power Panel on the wall.
2. Use a screwdriver to open the wiring hole of the Home Power Panel.
3. Install the wall brackets on the wall using 4 screws with the positioning card provided. (The vertical distance between the two screw holes is 9.86 in /
250.5 mm, and the horizontal distance between the two screw holes is 7.09 in / 180 mm.) Tighten all the screws with 5N·m torque.
4. Install the backplate brackets on the back of Anker SOLIX Home Power Panel. Tighten all the screws with 1.6N·m torque.
5. Secure the backplate brackets on Anker SOLIX Home Power Panel with the wall brackets.
6. Lock the backplate brackets from the side. You need to install 4 screws with 1.6N·m torque.
Install the 12-Circuit Backup Load Center (Optional)
Open the 12-Circuit Backup Load Center, align the casing's screws with the holes, and secure them to the wall with 5N*m torque.
Electrical Connections
Wiring to Home Main Panel
1. Remove the cover.
Remove the cover of the Home Main Panel.
Remove the panel from the wiring area beneath Anker SOLIX Home Power Panel.
2. Install the 100A circuit breaker.
Take out the 100A circuit breaker from the package and connect it to L1 and L2 on the Home Main Panel.
Align the breaker "FIN" with the Home Main Panel "SLOT."
Tilt the breaker back~45° and insert "FOOT" into the back pan.
While pulling the breaker towards the back pan slot, rotate down to lock into place.
3. Install cables.
Use a screwdriver to unscrew the grid wiring connectors with 5N·m torque.
Connect 4 cables to the grid wiring connectors with 5N·m torque. From left to right, they are: L1 / L2 / N / GND.
Run the 4 cables through the left hole of Anker SOLIX Home Power Panel and thread them into the bottom hole of the Home Main Panel.
Loosen the wire screws and insert 2 live wires into the 100A circuit breaker.
Loosen the wire screws, insert 1 neutral wire and 1 ground wire into the unused openings on the neutral bar and ground bar respectively. Then tighten the
screws.
4. Connect current transformers.
Open the 200A current transformers and snap them to L1 and L2 respectively. Orient the current transformers with the arrow pointing towards the power
source.
Note: If a solar power system is connected to Home Main Panel, the 100A current transformer can be clamped on the wire connected to the solar panel.
Insert the current transformers into the CT port of Anker SOLIX Home Power Panel. The cables of two 200A current transformers are connected to the
connectors labeled L1 and L2, and the cable of the 100A current transformer is connected to the connector labeled Solar.
Complete the wiring of Anker SOLIX Home Power Panel with Home Main Panel.
Wiring to 12-Circuit Backup Load Center (Optional)
1. Remove the green screw.
For circuit safety, remove the green screw to disconnect the neutral and ground bars.
2. Install the ground bar kit.
First, find the pre-drilled screw holes inside the 12-Circuit Backup Load Center, align the screw holes on the ground bar kit with them, and finally use
screws to install the ground bar kit inside the 12-circuit backup load center.
3. Install cables.
Use a screwdriver to unscrew the backup wiring connectors with 5N·m torque.
Connect 4 cables to the backup wiring connectors with 5N·m torque. From left to right, they are: L1 / L2 / N / GND.
Run the 4 cables through the right hole of Anker SOLIX Home Power Panel and thread them into bottom hole of the 12-Circuit Backup Load Center.
Connect two live wires to the backup load center's L1 and L2 connectors.
Loosen the wire screws and insert a neutral wire into the neutral bar and a ground wire into the ground bar.
4.Install the branch breaker.
Move the branch or circuit breakers that require emergency backup load from the main panel to the 12-Circuit Backup Load Center as needed.
Complete internal wiring of the 12-Circuit Backup Load Center.
Checking Connection
Before installing the front cover, check the following connection items.
Completing Installation
Reinstall the Panels
Reinstall the panels of Anker SOLIX Home Power Panel, the Home Main Panel, and the 12-Circuit Backup Load Center.
Connect to Anker SOLIX F3800 Portable Power Station
1. Connect Anker SOLIX F3800 Power Station to the bottom ports of Anker SOLIX Home Power Panel with the F3800 to Home Power Panel Cable.
Note: Anker SOLIX Home Power Panel can be connected with 1 or 2 power stations.
2. Turn on either Breaker 1 or Breaker 2 on the side of Home Power Panel, depending on the connection of Anker SOLIX F3800. For two Anker SOLIX
F3800 units, activate the breakers on both sides.
Turning On Anker SOLIX Home Power Panel
1. Check that the connection of the entire system has been completed.
2. Turn on the circuit breaker of the main panel and connect to utility power. Make sure the circuit breaker of the 12-Circuit Backup Load Center is also
turned on.
3. To ensure clear communication signals, please extend the antenna of Anker SOLIX Home Power Panel.
4. Press the On/Off button for 2 seconds to turn on Anker SOLIX Home Power Panel.
Starting to Use Your Anker SOLIX Home Power Panel
To learn how to use the Anker SOLIX Home Power Panel and the app, please scan the QR code below to view the user guide.
The Anker App for Smart Control
You can remotely control your Anker SOLIX F3800 Portable Power Station and Anker SOLIX Home Power Panel using the Anker app.
Please download the app by scanning this QR code or search Anker via the App Store or Google Play.
Specifications
Model
Product Weight
Product Dimensions
A17B1
19 lbs / 8.8 kg
19.7×13×5.7 in
500×330.2×144.8 mm
Installation
Wall
Warranty
5 Years
Rated System Voltage
120 / 240V AC
Grid Wiring Area (Input)
18kW Max, 75A Max, 60Hz, L1+L2+N+PE
Grid Wiring Area (Output)
6kW Max (Continuous), 25A Max (Continuous), 60Hz,
L1+L2+N+PE
Overvoltage Protection of Grid Wiring Phase Voltage:
Area
• Overvoltage Point: 135 ± 3V
• Duration: 200 ms
• Recovery Point: 132 ± 3V
• Recovery Time: 30 s
Line Voltage:
• Overvoltage Point: 270 ± 3V
• Duration: 200 ms
• Recovery Point: 265 ± 3V
• Recovery Time: 30 s
Undervoltage Protection of Grid Wiring Phase Voltage:
Area
• Undervoltage Point: 166 ± 3V
• Duration: 200 ms
• Recovery Point: 172 ± 3V
• Recovery Time: 30 s
Line Voltage:
• Undervoltage Point: 83 ± 3V
• Duration: 200 ms
• Recovery Point: 86 ± 3V
• Recovery Time: 30 s
Backup Wiring Area (Output)
12kW Max (Continuous), 50A Max (Continuous), 60Hz,
L1+L2+N+PE
Power Station 1 Ports (Input)
6kW Max, 25A Max, 60Hz, L1+L2+N+PE
Power Station 1 Ports (Output)
3.8kW Max (Continuous), 15.8A Max (Continuous), 60Hz,
L1+L2+N+PE
Power Station 2 Ports (Input)
6kW Max, 25A Max, 60Hz, L1+L2+N+PE
Power Station 2 Ports (Output)
3.8kW Max (Continuous), 15.8A Max (Continuous), 60Hz,
L1+L2+N+PE
Power Stations 1 and 2 Ports (Total
6kW Max (Continuous), 25A Max (Continuous), 60Hz,
Output)
L1+L2+N+PE
Power Stations 1 and 2 Ports (Total
12kW Max (Continuous), 50A Max (Continuous), 60Hz,
Input)
L1+L2+N+PE
Output Power Factor Rating
One Anker SOLIX F3800, (30% Load) 1.9 W Load, PF > 0.96
Two Anker SOLIX F3800s, (60% Load) 3.8kW Load, PF > 0.98
Two Anker SOLIX F3800s, (100% Load) 6kW Load, PF >
0.985
Nominal Output Voltage (AC)
120/240V
Normal Output Frequency
60Hz
Normal Temperature Range Operation -4°F - 104°F / -20°C - 40°C
Customer Service
US/CA: [email protected]
US/CA: +1 (800) 988 7973
">
