advertisement
s
Be inspired
Operating Manual
and Safety Precautions
!
Gigaset A100, IM eng, A31008-A100-B101-1-5819
Giga100.fm
03.02.04
Brief overview
Base station symbol
–
Constant: ready for dialling/receiving calls
–
Flashing: no connection to base station
Speed dialling
Recall key
– For PABXs and select carrier services
Dial pause
– Hold down!
Handset key
– Accept/end call
– Dial call number
(when digits are already stored)
Redial
Keypad lock
– Lock on/off hold down to activate/ deactivate!
Memory key
– For saving
– For settings
Displays
/ Base station symbol
d
Save
Special displays
n
* character
_
# character
u
Recall key
P
Pause
~
Memory empty
b
Lift handset
~~~~ Keypad lock
Handset ready for registration
Handset searching for registered base
Handset found base that is ready for registration
2
Gigaset A100, IM eng, A31008-A100-B101-1-5819
Giga100.fm
03.02.04
Safety information
!
$
Use only the plug-in power supply unit pro-
vided, as indicated on the bottom of the device.
‹
Use only approved, rechargeable batteries of
the same type. In other words, never use conventional (non-rechargeable) batteries, since these can injure you and damage your health.
Insert rechargeable batteries in accordance with polarity symbols (the instructions are found in the handset battery compartment).
Œ
Use the batteries indicated in these operating instructions (the instructions are found in the handset's battery compartment).
The operation of medical equipment may be affected. Bear in mind the technical requirements of the environment (e.g. doctor's office).
The handset can cause an unpleasant buzzing sound in hearing aids. Do not hold the handset too close to your ear.
Do not operate the telephone in environments where there is risk of explosion (e.g. paint shops).
Do not install the base station in bathrooms or
showers.The handset is not splashproof (see page 13).
ƒ
Do not pass your Gigaset on to a third party without the user guide.
Dispose of batteries and your phone in an environment-friendly manner.
When the keypad is locked (see page 11) emergency num-
bers cannot be dialled either.
Not all the functions described in this user guide are available in all countries.
3
Gigaset A100, IM eng, A31008-A100-B101-1-5819
Giga100.fm
03.02.04
Putting the telephone into service
Step 1: Connecting the base station
First of all, connect your base station to the telephone jack and the mains supply.
220 V/
230 V
Telephone jack*
• Insert the round plug of the mains cable into the jack.
• Lay the cable in the channel provided (to prevent overtensioning).
• Plug the power supply unit into the power socket.
• Plug the square connector of the phone cable supplied into the jack.
• Lay the cable in the channel.
• Plug the phone connector into the phone socket.
* Appearance may differ, depending on country!
If you do not want to use the telephone cable supplied, ensure that you use either a simple extension cable or a telephone cable with 3/4 connector assignment, otherwise your Gigaset A100 will not function correctly.
1 free
2 free
3 L a
4 L b
5 free
6 free
4
Gigaset A100, IM eng, A31008-A100-B101-1-5819
Giga100.fm
03.02.04
Putting the telephone into service
Step 2: Inserting the battery
• Insert the battery connector into the socket (see inset); it must lock securely into place.
• Place battery in the battery compartment.
• Insert battery cable in the clip provided.
• Put the battery compartment cover on and push it up until it latches into position. To open the compartment, press on the ridged section of the cover and push downwards.
• Only use approved batteries.
• Never use non-Siemens charging units as these can damage the batteries.
The display is protected by a film.
Please remove protective film.
5
Gigaset A100, IM eng, A31008-A100-B101-1-5819
Giga100.fm
03.02.04
Putting the telephone into service
Step 3: Registering the handset at the base station
Before you can make or receieve telephone calls you need to register the handset at the base station.
Make sure that the base station is connected to the power supply (Step 1) and the battery is inserted in the handset (Step 2).
Place the handset in the base station and leave it there until registration is complete.
k
Ö
The registration display will appear. This may take up to 5 minutes, depending on the charge level of the battery.
The
/
symbol will flash in the display.
Unplug the power supply unit (220V/230V) from the mains socket.
The handset must remain in the base station. Plug the power supply unit back into the mains socket.
After about 90 seconds the
/ symbol will stop flashing and the normal standby display will appear. The handset is now registered at this base station.
6
Gigaset A100, IM eng, A31008-A100-B101-1-5819
Giga100.fm
03.02.04
Putting the telephone into service
Step 4: Charging the battery
The battery supplied is not charged.
k
Ö
To charge the battery, place the handset in the base station. For the first charging we recommend a continuous charging time for at least 16 hours.
You can then make calls.
Battery information
• Once the first charging operation is completed, you can replace the handset in the base station after any call.
• The batteries warm up during charging - this is normal and not a cause for concern.
Handset operating times/charging time
Capacity
Standby time
Talktime
300 (mAh) up to 100 hrs up to 10 hrs
Charging time
approx.
16 hrs
Approved battery
Nickel-cadmium (NiCd)
Type 1a (300 mAh)V30145-K1310-X147 NiCd
Batteries are available from your stockist, the Siemens
Customer Care or via the Internet, from Siemens Service
Shop at: http://communication-market.siemens.de/serviceshop/ default.asp; alternatively see also last page.
7
Gigaset A100, IM eng, A31008-A100-B101-1-5819
Giga100.fm
03.02.04
Making calls
Making a call
o
Enter the call number.
a
Press the handset key. A connection is set up. The icon b appears in the display.
.
Did you enter the wrong number by mistake? If so, then press the handset key a twice.
You can also dial a number by pressing the handset key first and then entering the relevant digits.
You can use the recall key
R
to insert a pause (hold the key down). This may be necessary for international calls or when dialling in to automatic announcement services.
Ending a call a
Press the handset key. The icon b
disappears from the display;
or
Place the handset in the base station.
The connection is cleared down.
k
Ö
Accepting a call a
Press the handset key. The connection is set up.
Redialling a number
The last call number dialled is saved.
O
a
Dial the call number.
Press the handset key. The connection is set up.
8
Gigaset A100, IM eng, A31008-A100-B101-1-5819
Giga100.fm
03.02.04
Making calls
Saving/changing a call number (speed dialling)
You can save up to 10 telephone numbers as speed dialling digits and dial them at the push of a button.
¦ C e.g. o
¦
Press the memory key followed by the speed dialling key.
Enter the speed dialling digit (0 to 9).
Enter the call number.
Save the speed dialling digit. You will hear the confirmation beep.
Speed dialling
C
Press the speed dialling key.
e.g.
a
Select the speed dialling digit (0 to 9).
Press the handset key. The connection is set up.
The speed dialling digit "0" is activated automatically by holding down number with the identification the speed dialling key. We therefore recommend assigning a frequently dialled number to "0" (e.g. a network access number).
Cost-effective telephony
You can use the network access numbers of various providers to minimise costs (Call-by-Call
*
), depends on the offering of the service provider. Like a call number, these numbers can be saved as speed dialling digits (0 to 9).
You can, however, also dial the network access or call numbers as usual.
• Network access using a speed dialling digit
C
Hold down the speed dialling key.The speed dial memory location "0" with the network access number is displayed automatically. o
a
Enter the user’s call number and dial the complete number via the handset keypad.
* not available in all countries
9
Gigaset A100, IM eng, A31008-A100-B101-1-5819
Giga100.fm
03.02.04
Cost-effective telephoning
• "Linking" or chaining of multiple speed dialling digits
You can link multiple access numbers and call numbers that have been saved as speed dialling numbers.
C e.g.
Hold down the speed dialling key.
Memory location "0" with the network access number is displayed.
C e.g.
5
Press the speed dialling key once more.
Select the speed dialling digit (0 to 9) for a user. The network access number and the call number are chained and displayed.
a
Press the handset key. The connection is set up.
Further access numbers can be saved as speed dialling numbers (0 to 9).
To use them press C and then the relevant speed dialling key.
Settings
Handset volume
You can set the handset volume to any of three levels.
¦ Þ
Activate the function.
e.g.
Ÿ¦
Change the volume (levels 1 to 3) and save.
Ringer volume
You have three volumes to choose from.
¦ ¢
Activate the function – the ringer sounds.
e.g.
Ÿ¦ Change the ringer volume (levels 1 to 3) and save.
10
Gigaset A100, IM eng, A31008-A100-B101-1-5819
Giga100.fm
03.02.04
Settings
Ringtone
You can choose between two ringtones.
¦ ´
Activate the function – the ringer sounds.
e.g.
Ÿ¦
Select the ringtone (version 1 or 2) and save.
Keypad lock
When the keypad is locked, nothing happens if you inadvertently press a key. You can continue to accept calls in the usual manner.
ª
Hold down for more than
1 second to activate/deactivate.
~~~~
The display icon appears if active.
Operating behind a PABX
If you operate your Gigaset behind a PABX, it may be necessary to change the preset Dual Tone Multifrequency Dialling
(DTMF) procedure and flash times (please refer to the operating instructions of your PABX).
Use digits 1 to 4 to set the following:
1 DTMF, long flash 250 ms
2 DTMF, short flash 100 ms
3 DP (Dial Pulsing) 1.5/1
4 DP 2/1
a
¦ Þ e.g.
4
¦
a
Press the handset key.
Activate the function by entering 10.
Enter the desired setting (1 to 4).
Save the setting.
Press the handset key.
Did you enter the wrong number by mistake? Then press the handset key to standby.
a
twice or wait until the display returns
11
Gigaset A100, IM eng, A31008-A100-B101-1-5819
Giga100.fm
03.02.04
Registering the handset manually
Handset A1 to an A100 base:
Manual registration has to be carried out if
• automatic registration has not functioned or
• the original handset supplied has been replaced.
Remove the power supply unit (220V/230V) from its socket.
¦ 7 ¦
Prepare the handset for registration.
k
Ö
Place the handset in the base station and leave it there until registration has been completed.
Make sure the handset is still in the base station. Now replug the power supply unit into the socket.
The handset will now take about 60 seconds searching for a base that is ready for registration.
A base that is ready for registration has been found; registration was successful (display appears for about 3 seconds).
No base ready for registration has been found (display appears for about 3 seconds).
• Manual handset registration will overwrite an existing registration.
• The search for a base that is ready for registration can be cancelled by pressing the handset key a .
12
Gigaset A100, IM eng, A31008-A100-B101-1-5819
Giga100.fm
03.02.04
Tips
Maintenance
Simply wipe your telephone with a damp cloth or an antistatic wipe. Never use a dry cloth as this can cause static discharge!
Contact with liquid
!
If the handset should come into contact with liquid,
on no account switch the device on.
Remove all batteries immediately.
Allow the liquid to drip out of the device, and then dab all parts of the device dry.
Keep the handset with the batteries removed in a warm, dray place for at least 72 hours. In many cases, you will then be able to use it again.
Troubleshooting
Malfunction
Registration did not work.
No display.
No reaction to keystroke.
Possible causes Solution
The battery is not sufficiently charged.
Handset and base station were not prepared for registration.
The battery is not charged.
The keypad is locked.
Charge the battery for 16 hours
Remove and then re-insert the power supply unit.
Charge the battery or replace it
Press
ª for
1 second.
13
Gigaset A100, IM eng, A31008-A100-B101-1-5819
Giga100.fm
03.02.04
Malfunction
No radio connection to the base station: flashing!
/
icon
Possible causes Solution
The handset is outside the base station range.
Move closer to the base station.
The handset is not registered.
The base station is not active.
Register the
Insert round plug of the mains cable into jack and lay the cable in cable channel
(to prevent overtensioning).
Plug the power supply unit into the power socket.
Range
doors. The base station symbol is exceeded.
/
flashes when the range
Customer Care
You can get assistance easily when you have technical questions or questions about how to use your device by using our online support service on the Internet at:
www.my-siemens.com/customercare
or by referring to the section entitled
Questions and
answers in this manual (page 13).
If the device needs to be repaired, please contact one of our
Customer Care Centers
:
Abu Dhabi.....................................................................0 26 42 38 00
Argentina .................................................................0 80 08 88 98 78
Australia......................................................................18 00 62 24 14
Austria ........................................................................05 17 07 50 04
Bahrain .................................................................................40 42 34
Bangladesh...................................................................0 17 52 74 47
Belgium ........................................................................0 78 15 22 21
Bosnia Herzegovina......................................................0 33 27 66 49
Brazil........................................................................0 80 07 07 12 48
Brunei ..............................................................................02 43 08 01
Bulgaria............................................................................02 73 94 88
14
Gigaset A100, IM eng, A31008-A100-B101-1-5819
Giga100.fm
03.02.04
Cambodia ........................................................................12 80 05 00
Canada.....................................................................1 88 87 77 02 11
China .......................................................................0 21 50 31 81 49
Croatia ..........................................................................0 16 10 53 81
Czech Republic...........................................................02 33 03 27 27
Denmark..........................................................................35 25 86 00
Dubai ............................................................................0 43 96 64 33
Egypt ............................................................................0 23 33 41 11
Estonia.............................................................................06 30 47 97
Finland........................................................................09 22 94 37 00
France ........................................................................01 56 38 42 00
Germany.....................................................................01805 333 222
Greece.....................................................................0 80 11 11 11 16
Hong Kong.......................................................................28 61 11 18
Hungary ......................................................................06 14 71 24 44
Iceland ...............................................................................5 11 30 00
India.....................................................................01 13 73 85 89 - 98
Indonesia .................................................................0 21 46 82 60 81
Ireland.........................................................................18 50 77 72 77
Italy.............................................................................02 66 76 44 00
Ivory Coast ......................................................................80 00 03 33
Jordan...........................................................................0 64 39 86 42
Kenya.................................................................................2 72 37 17
Kuwait ...............................................................................2 45 41 78
Latvia .................................................................................7 50 11 14
Lebanon...........................................................................01 44 30 43
Libya...........................................................................02 13 50 28 82
Lithuania .......................................................................8 22 74 20 10
Luxembourg ................................................................... 43 84 33 99
Macedonia.......................................................................02 13 14 84
Malaysia .....................................................................03 21 63 11 18
Malta ................................................................00 35 32 14 94 06 32
Mauritius ...........................................................................2 11 62 13
Mexico...................................................................01 80 07 11 00 03
Morocco ..........................................................................22 66 92 09
Netherlands .................................................................0900-3333102
New Zealand ..............................................................08 00 27 43 63
Norway ............................................................................22 70 84 00
Oman....................................................................................79 10 12
Pakistan ......................................................................02 15 66 22 00
Philippines ....................................................................0 27 57 11 18
Poland.........................................................................08 01 30 00 30
Portugal ........................................................................8 00 85 32 04
Qatar................................................................................04 32 20 10
Romania .....................................................................02 12 04 60 00
Russia....................................................................... (800) 200 10 10
Saudi Arabia..................................................................0 22 26 00 43
Serbia .........................................................................01 13 22 84 85
Singapore ........................................................................62 27 11 18
Slovak Republic ..........................................................02 59 68 22 66
Slovenia ........................................................................0 14 74 63 36
South Africa................................................................08 60 10 11 57
Spain.............................................................................9 02 11 50 61
Sweden ........................................................................0 87 50 99 11
Switzerland.................................................................08 48 21 20 00
Taiwan ........................................................................02 25 18 65 04
Thailand ........................................................................0 22 68 11 18
Tunisia ........................................................................01 71 10 81 08
15
Gigaset A100, IM eng, A31008-A100-B101-1-5819
Giga100.fm
03.02.04
Turkey......................................................................0 21 65 79 71 00
Ukraine ....................................................................8 80 05 01 00 00
United Arab Emirates ...................................................0 43 31 95 78
United Kingdom.......................................................0 87 05 33 44 11
USA .........................................................................1 88 87 77 02 11
Vietnam ...........................................................................45 63 22 44
Your Gigaset is intended for operation in your country, as depicted on the underside of the base unit. Country-specific features have been taken into account.
The conformity of the device with the essential requirements of the R&TTE directive is confirmed by the CE symbol.
Excerpt from the original declaration:
"We, Siemens AG, declare, that the above mentioned product is manufactured according to our Full Quality Assurance
System certified by CETECOM ICT Services GmbH with the registration number "Q810820M" in compliance with ANNEX
V of the R&TTE Directive 99/05/EC. The presumption of conformity with the essential requirements regarding Council
Directive 99/05/EC is ensured.“
Senior Approvals Manager
The Declaration of Conformity (DoC) has been signed. In case of need, a copy of the original DoC can be made available via the company hotline.
16
s
Be inspired
Notice d'utilisation
et consignes de sécurité
!
Gigaset A100, IM franz, A31008-A100-B101-1-5819
Giga_A100.f
3.2.04
Présentation
Symbole de la base
–
Continu : prêt pour la numérotation/réception
–
Clignotant : déconnexion de la base
Mémoires
- N° abrégés
Touche "R"
– Pour services réseau
Pause interchiffre
– Appui prolongé !
Touche "Combiné"
– Accepter/Mettre fin à la communication
– Prise de ligne
/Numérotation
Touche BIS
Protection clavier
– Activer/désactiver appui prolongé !
Touche Programmation
– Pour enregistrer
– Pour régler
Symboles de l’afficheur
/ Symbole de la base d
Programmation
Caractères spéciaux
n
Caractère *
_
Caractère # u
Touche "R" b
P
Pause
~
Mémoire vide
Décroché / prise de ligne
~~~~
Protection du clavier
Combiné prêt pour la déclaration
Combiné recherche la base déclarée
Combiné a trouvé la base déclarée
2
Gigaset A100, IM franz, A31008-A100-B101-1-5819
Giga_A100.f
3.2.04
Consignes de sécurité
!
$
Utiliser exclusivement le bloc-secteur fourni, comme indiqué sous la base par le symbole.
Utiliser uniquement une batterie homologuée
Ne jamais utiliser des piles normales (non rechargeables) qui peuvent endommager l’appareil, représenter un risque pour la santé et peuvent provoquer des blessures.
Raccordez la batterie en respectant la polarité
‹
Œ
Utiliser la batterie en respectant le présent mode d’emploi. (Dans le logement de batterie du combiné figurent les instructions suivantes.)
Le combiné peut perturber le fonctionnement de certains équipements médicaux. Tenir compte des recommandations émises à ce sujet par le corp médical.
Le combiné peut provoquer un bourdonnement dans les aides auditives. Ne pas tenir le combiné directement à proximité de l’oreille pendant la sonnerie (lors d’un appel entrant).
Ne pas utiliser le téléphone dans un environnement présentant un risque d’explosion (p. ex. ateliers industriels de peinture).
Ne pas implanter la base dans une salle de bain ou une salle d’eau et plus généralment en tout milieu humide ou en extérieur. Le combiné mobile n’est pas étanche aux projections d’eau
Lorsque vous confiez votre Gigaset à un tiers, toujours joindre le mode d’emploi.
ƒ
Bien respecter les règles concernant la protection de l’environnement lorsque vous mettez au rebut le téléphone et les batteries. Ne pas jeter ces dernières au feu, ni les ouvrir ou les mettre en court-circuit.
Si le verrouillage du clavier est activé (voir page 11), il est
impossible de composer même les numéros d’urgence.
Toutes les fonctions décrites dans ce mode d’emploi ne sont pas nécessairement disponibles dans tous les pays.
3
Gigaset A100, IM franz, A31008-A100-B101-1-5819
Giga_A100.f
3.2.04
Mise en service du téléphone
Opération 1 : raccorder la base
Raccorder tout d’abord la base à la prise téléphonique et au réseau électrique.
Fiche téléphonique*
6
3
220 V/
230 V
2
4
5
1
1. Insérer le connecteur rond du cordon électri-
que dans la prise adéquate de la base.
2. Placer le cordon dans la rainure (pour sécuriser mécaniquement la connexion).
3. Insérer le bloc-secteur dans la prise électrique.
4. Insérer le petit connecteur du cordon téléphonique fourni dans la prise adéquate de la base.
5. Placer le cordon dans la rainure.
6. Insérer le connecteur en " T " du cordon téléphonique fourni dans la prise téléphone.
* modèle différent selon le pays
Si vous souhaitez un autre cordon téléphonique que celui fourni, bien veiller à utiliser une rallonge simple ou un cordon téléphonique avec brochage de connecteur 3-/4, sinon votre
Gigaset A100 ne fonctionnera pas.
1 libre
2 libre
3 L a
4
5
6
L b libre libre
4
Gigaset A100, IM franz, A31008-A100-B101-1-5819
Giga_A100.f
3.2.04
Mise en service du téléphone
Opération 2 : insérer la batterie
• Insérer dans la prise le connecteur de batterie en observant le sens imposé par le détrompeur (voir agrandissement), le connecteur doit être fermement enclipsé.
• Placer la batterie dans son logement, appuyer jusqu'à l'enclipsage.
• Coincer le câble de la batterie dans la fixation prévue.
• Positionner le couvercle à plat puis le décaler en glissant vers le haut jusqu'à ce qu’il s’enclipse. Pour ouvrir, appuyer sur la partie striée et faire glisser vers le bas.
• N’utiliser que les batteries homologuées.
• Ne pas utiliser de chargeurs d’autres constructeurs qui risquent d’endommager la batterie.
L'afficheur est protégé par un film.
Retirer celui-ci SVP.
5
Gigaset A100, IM franz, A31008-A100-B101-1-5819
Giga_A100.f
3.2.04
Mise en service du téléphone
Etape 3 : déclarer le combiné sur la base
Pour pouvoir téléphoner, vous devez préalablement enregistrer le combiné sur la base.
Bien vérifier que votre base est raccordée
(étape 1) et que la batterie est insérée dans le combiné (étape 2).
k
Ö
Placer le combiné dans la base et l’y laisser jusqu’à ce que la déclaration soit terminée.
Selon l’état de charge de la batterie, l’affichage correspondant à la déclaration apparaît au bout de quelques minutes.
Sur l’écran, le symbole
/ clignote.
Débrancher le bloc-secteur (220V/230V) de la prise.
Vérifier que le combiné est toujours dans la base. Brancher de nouveau le bloc-secteur.
/ cesse de clignoter et l’affichage correspondant à la position de veille apparaît à l’écran. Le combiné est déclaré sur la base.
6
Gigaset A100, IM franz, A31008-A100-B101-1-5819
Giga_A100.f
3.2.04
Mise en service du téléphone
Etape 4: charger la batterie
La batterie fournie n’est pas chargée.
k
Ö
Pour charger la batterie, placer le combiné dans la base. La première fois, charger la batterie sans interruption durant au moins 16 heures.
Après vous pouvez téléphoner.
Remarques sur la batterie
• Une fois la première charge effectuée, vous pouvez reposer le combiné sur la base après chaque communication.
• La batterie s’échauffe durant la charge ; il s’agit d’un phénomène normal, qui ne présente aucun danger.
Autonomie / Durée de chargement du combiné
Capacité
Autonomie en veille
Autonomie en communication
Durée de chargement
300 (mAh) 100 h maxi.
10 h maxi.
16 h environ
Batterie homologuée
Nickel-Cadmium (NiCd)
Désignation 1a (300 mAh)V30145-K1310-X147 NiCd
Vous pouvez vous procurer les batteries auprès de magasins spécialisés, du service clients ou de la boutique en ligne de
Siemens accessible depuis le site internet http://communication-market.siemens.de/serviceshop).
7
Gigaset A100, IM franz, A31008-A100-B101-1-5819
Giga_A100.f
3.2.04
Téléphoner
Appeler o a
Composer le numéro.
Appuyer sur la touche "Combiné". La communication est établie. Sur l’afficheur apparaît le symbole b .
Vous avez fait une erreur ?
Appuyez 2 x sur la touche "Combiné"
a
Pour numéroter, vous pouvez aussi appuyer tout d’abord sur la touche "Combiné", puis entrer les chiffres.
La touche "Flashing"
R
permet d’insérer une pause
interchiffre (appui prolongé). Cela peut être nécessaire pour les communications avec l’étranger ou pour sélectionner des services d’annonces automatiques.
Mettre fin à la communication a
Appuyer sur la touche "Combiné". Le symbole b n’est plus visible sur l’afficheur ;
ou
k
Ö
Poser le combiné sur la base.
La communication est coupée.
Répétition de la numérotation (Bis)
Le dernier numéro composé est enregistré, pour le rappeler:
O a
Sélectionner le numéro.
Appuyer sur la touche "Combiné". La communication est établie.
Prendre un appel a
Le téléphone sonne. Appuyer sur la touche
"Combiné". La communication est établie.
8
Gigaset A100, IM franz, A31008-A100-B101-1-5819
Giga_A100.f
3.2.04
Téléphoner
Mémoires / Numérotation abrégée
Le Gigaset A100 permet l'enregistrement de 10 numéros en mémoire dont l'accès indirect se fait facilement par une numérotation abrégée ( 0 à 9).
Pour enregistrer :
¦ C
Appuyer sur la touche Programmation puis sur la touche "Mémoires".
p. ex. Sélectionner le numéro abrégé (0 à 9).
La position mémoire s'affiche à gauche de l'écran avec :
- le symbole [
~
] en cas de mémoire vide
- le numéro déjà enregistré (8 caractères se décalant vers la gauche)
o
¦
Entrer le nouveau numéro.
Valider, vous entendez un bip de confirmation.
Pour numéroter à l’aide d’un n° abrégé :
C
Appuyer sur la touche "Mémoires".
p. ex. Sélectionner le n° abrégé (0 à 9), le numéro enregistré s'affiche.
a
Appuyer sur la touche "Combiné". La communication est établie.
Le n° abrégé "0" est automatiquement activé par simple appui prolongé de la touche "Mémoires"
C
. Il est donc recommandé d’enregistrer sous "0" un numéro très souvent utilisé.
9
Gigaset A100, IM franz, A31008-A100-B101-1-5819
Giga_A100.f
3.2.04
Réglages
Pour chaîner préfixe et numéro
Comme pour un numéro ordinaire, vous pouvez aussi enregistrer en mémoire, sous un N° abrégé facilement utilisable
(0 à 9), des préfixes que vous pourrez ensuite compléter manuellement ou chaîner avec le numéro d'une autre position mémoire.
• Utilisation du n° abrégé rapide (mémoire n°0)
C
Appuyer de façon prolongée sur la touche
"Mémoires" . .Le préfixe ou numéro enregistré sous le n° abrégé "0" s’affiche automati-
quement.
o a
Compléter éventuellement par le numéro du correspondant puis composer la séquence complète en appuyant sur la touche "Combiné".
• "Chaînage" de préfixes et numéros
Si vous avez enregistré plusieurs préfixes et numéros sous des numéros abrégés distincts vous pouvez les associer.
A partir du numéro abrégé rapide (mémoire 0):
C
Appuyer de façon prolongée sur la touche
"Mémoires". Le préfixe enregistré sous le n° abrégé "0" s’affiche.
C
Appuyer de nouveau sur la touche "Mémoires".
p. ex.
5
Sélectionner le numéro abrégé (0 à 9) correspondant à un abonné. Le préfixe et le numéro sont chaînés et affichés.
a
Appuyer sur la touche "Combiné". La communication est établie.
Vous pouvez mémoriser d’autres préfixes en tant que numéros abrégés sous les touches 1 à 9.
Pour les utiliser, appuyer brièvement sur la touche
C
puis sur la touche correspondante (1 à 9) et poursuivre le chaînage comme ci-dessus.
10
Gigaset A100, IM franz, A31008-A100-B101-1-5819
Giga_A100.f
3.2.04
Réglages
Volume de l’écouteur du combiné
Vous avez le choix entre trois volumes pour l’écouteur du combiné.
¦ Þ
Activer la fonction.
p. ex.
Ÿ¦
Modifier le volume (niveau 1 à 3) et enregistrer.
Volume de la sonnerie
Vous avez le choix entre trois volumes de sonnerie, tous crescendo.
¦ ¢
Activer la fonction – la sonnerie est diffusée.
p. ex.
Ÿ¦
Modifier le volume de la sonnerie (niveau
1 à 3) et enregistrer.
Mélodie de la sonnerie
Vous avez le choix entre deux mélodies pour la sonnerie.
¦ ´
Activer la fonction – la sonnerie est diffusée.
p. ex.
Ÿ¦
Sélectionner la mélodie de la sonnerie
(variante 1 ou 2) et enregistrer.
Protection du clavier
Cette protection permet d'éviter toute manipulation involontaire des touches. Vous pouvez toutefois prendre un appel comme d’habitude.
ª
Pour activer/désactiver appuyer durant plus
de 1 seconde.
~~~~
Lorsque la protection est activée, le symbole ci-contre s’affiche.
11
Gigaset A100, IM franz, A31008-A100-B101-1-5819
Giga_A100.f
3.2.04
Réglages
Installation derrière un autocommutateur privé
Si vous utilisez votre Gigaset derrière un autocommutateur privé, il peut être nécessaire de régler un mode de numérotation différent du mode FV et du flashing paramétrés par défaut (voir le mode d’emploi de votre autocommutateur).
Les chiffres 1 à 4 correspondent aux réglages suivants.
1 FV, flashing long 250 ms (valeur par défaut)
2 FV, flashing court 100 ms
3 DC (numérotation décimale) 1.5/1
4 DC 2/1
a
¦ Þ
p. ex.
4
¦ a
Appuyer sur la touche "Combiné".
Pour activer la fonction sélectionner 10.
Sélectionner le réglage souhaité (1 à 4).
Enregistrer le réglage.
Appuyer sur la touche "Combiné".
Vous avez fait une erreur ? Appuyez 2 x sur la touche "Combiné" a
ou bien attendez que l’afficheur revienne de luimême à l’état de base.
12
Gigaset A100, IM franz, A31008-A100-B101-1-5819
Giga_A100.f
3.2.04
Déclarer le combiné manuellement
Placer le combiné A1 sur la base du A100
Une déclaration manuelle est utile lorsque,
• la déclaration automatique n’a pas fonctionné,
• le combiné fourni a été échangé.
Retirez le bloc-secteur (220V/230V) de la prise électrique.
¦ 7 ¦
Préparez le combiné pour le déclarer.
Placez le combiné dans la base et laissez l’y jusqu’à ce que la déclaration soit terminée.
k
Ö
Veillez à ce que le combiné se trouve bien sur la base. Placez à présent le bloc-secteur de nouveau dans la prise électrique.
Le combiné recherche pendant env. 60 secondes une base prête pour la déclaration.
Une base prête pour la déclaration a été trouvée, la déclaration a été effectuée avec succès (l’affichage apparaît pendant env. 3 secondes).
Aucune base prête pour la déclaration n’a
été trouvée (l’affichage apparaît pendant env. 3 secondes).
• La base A100 est mono combiné et ne peut avoir qu'un seul combiné déclaré à la fois.
• La déclaration manuelle d’un combiné écrase une déclaration existante.
• La recherche d’une base prête pour la déclaration peut
être interrompue à l’aide de la touche Combiné.
13
Gigaset A100, IM franz, A31008-A100-B101-1-5819
Giga_A100.f
3.2.04
Conseils pratiques
Entretien
Essuyer votre téléphone avec un chiffon légèrement humi-
difié ou un chiffon antistatique. Ne jamais utiliser de chiffon sec : risque de charge statique !
Contact avec les liquides
!
Si le poste mobile a été mis en contact avec un liquide,
il ne faut en aucun cas le mettre en marche.
Retirer tous les accumulateurs immédiatement.
Laisser le liquide s'écouler, sécher toutes les parties avec un linge absorbant.
Placer le mobile sans accumulateurs pendant au moins 72 heures dans un endroit chaud et sec.
Ensuite, dans la plupart des cas le mobile fonctionnera à nouveau.
Tabelle:
Remédier aux défaillances
Symptôme
La déclaration ne s’est pas faite.
Aucun affichage.
Cause possible Remède
La batterie n’est pas suffisamment chargée.
La batterie est vide.
Charger la batterie durant
16 heurs
Débrancher le bloc-secteur puis
Charger la batterie ou la rempla-
Aucune réaction lorsque vous appuyez sur les touches.
La protection du clavier est activée.
Appuyer durant
1 seconde sur la touche
ª
.
14
Gigaset A100, IM franz, A31008-A100-B101-1-5819
Giga_A100.f
3.2.04
Symptôme
Aucune liaison radio avec la base : le symbole clignote !
/
Cause possible Remède
Le combiné se trouve hors de la zone de couverture de la base.
Se rapprocher de la base.
Le combiné n’est pas déclaré.
La base n’est pas active.
Déclarer le com-
Insérer le connecteur rond du cordon électrique dans la prise et placer le cordon dans la rainure
(pour diminuer le tirage). Insérer le bloc-secteur dans la prise électrique.
Portée
champs libre. Le symbole de la base
/ se met à clignoter lorsque vous quittez la zone de couverture de la base.
Service Clients
Si vous avez des questions techniques ou d'utilisation de votre appareil, le moyen le plus simple est de solliciter l'assistance de notre site Internet:
www.my-siemens.com/customercare
vous trouverez également dans le manuel d'utilisation, cha-
pitre Questions-réponses (voir page 14) des réponses aux
questions les plus fréquentes.
Dans le cas où une réparation s'avérerait nécessaire, adressez-vous à l'un de nos centres de SAV:
Abou Dhabi.................................................................. 0 26 42 38 00
Afrique du Sud .......................................................... 08 60 10 11 57
Allemagne .............................................................. 0 18 05 33 32 22
Arabie Saoudite ........................................................... 0 22 26 00 43
Argentine................................................................ 0 80 08 88 98 78
Australie .................................................................... 18 00 62 24 14
Autriche ..................................................................... 05 17 07 50 04
Bahrein ................................................................................ 40 42 34
Bangladesh.................................................................. 0 17 52 74 47
15
Gigaset A100, IM franz, A31008-A100-B101-1-5819
Giga_A100.f
3.2.04
Belgique ...................................................................... 0 78 15 22 21
Bosnie Herzégovine .................................................... 0 33 27 66 49
Brésil ...................................................................... 0 80 07 07 12 48
Brunei ............................................................................. 02 43 08 01
Bulgarie .......................................................................... 02 73 94 88
Cambodge ...................................................................... 12 80 05 00
Canada.................................................................... 1 88 87 77 02 11
Chine ...................................................................... 0 21 50 31 81 49
Côte-d'Ivoire ................................................................... 80 00 03 33
Croatie ......................................................................... 0 16 10 53 81
Danemark ....................................................................... 35 25 86 00
Dubai ........................................................................... 0 43 96 64 33
Egypte ......................................................................... 0 23 33 41 11
Emirats Arabes Unis.................................................... 0 43 31 95 78
Espagne....................................................................... 9 02 11 50 61
Estonie ........................................................................... 06 30 47 97
Finlande..................................................................... 09 22 94 37 00
France ....................................................................... 01 56 38 42 00
Grèce...................................................................... 0 80 11 11 11 16
Hong Kong...................................................................... 28 61 11 18
Hongrie...................................................................... 06 14 71 24 44
Inde .................................................................... 01 13 73 85 89 - 98
Indonésie................................................................ 0 21 46 82 60 81
Irlande........................................................................ 18 50 77 72 77
Islande .............................................................................. 5 11 30 00
Italie........................................................................... 02 66 76 44 00
Jordanie....................................................................... 0 64 39 86 42
Kenya................................................................................ 2 72 37 17
Koweït .............................................................................. 2 45 41 78
Lettonie ............................................................................ 7 50 11 14
Liban............................................................................... 01 44 30 43
Lithuanie...................................................................... 8 22 74 20 10
Luxembourg ................................................................... 43 84 33 99
Lybie.......................................................................... 02 13 50 28 82
Macédoine...................................................................... 02 13 14 84
Malaisie ..................................................................... 03 21 63 11 18
Malte ............................................................... 00 35 32 14 94 06 32
Maroc ............................................................................. 22 66 92 09
Maurice ............................................................................ 2 11 62 13
Mexique ............................................................... 01 80 07 11 00 03
Norvège.......................................................................... 22 70 84 00
Nouvelle-Zélande....................................................... 08 00 27 43 63
Oman................................................................................... 79 10 12
Pakistan ..................................................................... 02 15 66 22 00
Pays-Bas..................................................................... 0900-3333102
Philippines ................................................................... 0 27 57 11 18
Pologne ..................................................................... 08 01 30 00 30
Portugal ....................................................................... 8 00 85 32 04
Qatar............................................................................... 04 32 20 10
Rép. Slovaque ........................................................... 02 59 68 22 66
Rép. Tchèque ............................................................ 02 33 03 27 27
Roumanie .................................................................. 02 12 04 60 00
Royaume-Uni.......................................................... 0 87 05 33 44 11
Russie...................................................................... (800) 200 10 10
Serbie ........................................................................ 01 13 22 84 85
Singapour ....................................................................... 62 27 11 18
Slovénie....................................................................... 0 14 74 63 36
Suède .......................................................................... 0 87 50 99 11
16
Gigaset A100, IM franz, A31008-A100-B101-1-5819
Giga_A100.f
3.2.04
Suisse........................................................................ 08 48 21 20 00
Taiwan ....................................................................... 02 25 18 65 04
Thaïlande ..................................................................... 0 22 68 11 18
Tunisie ....................................................................... 01 71 10 81 08
Turquie ................................................................... 0 21 65 79 71 00
Ukraine ................................................................... 8 80 05 01 00 00
USA ........................................................................ 1 88 87 77 02 11
Vietnam .......................................................................... 45 63 22 44
Zimbabwe ...................................................................... 04 36 94 24
Votre Gigaset est homologué dans votre pays comme indiqué par le label figurant sous l’appareil. Les spécificités nationales sont prises en compte.
La conformité de l’appareil avec les exigences fondamentales de la directive européenne
R&TTE (99/05/CEE), est confirmée par le label CE.
Extrait de la déclaration originale :
"We, Siemens AG, declare, that the above mentioned product is manufactured according to our Full Quality Assurance System certified by CETECOM ICT Services GmbH with the registration number "Q810820M" in compliance with ANNEX V of the R&TTE-Directive 99/05/EC. La présomption de conformité avec les exigences essentielles de la Directive 99/05/CE est assurée."
Senior Approvals Manager
The Declaration of Conformity (DoC) has been signed. In case of need, a copy of the original DoC can be made available via the company hotline.
17
Gigaset A100 is designed for operation in your country as indicated on the box and on the machine. Special country-specific features have been taken into consideration. If you have any queries with regard to differences in public telephone networks, please contact your dealer or operator. Unit compliance with the basic requirements of the R&TTE directive is confirmed by the CE symbol.
"We, Siemens AG, declare, that the above mentioned product is manufactured according to our Full Quality
Assurance System certified by CETECOM ICT Services
GmbH with the registation number Q810820M in compliance with ANNEXE V of the R&TTE Directive 99/05/
EC. The presumption of conformity with the essential requirements regarding Council Directive 99/05/EC is ensured."
Senior Approvals Manager
The Declaration of Conformity (DoC) has been signed.
In case of need, a copy of the original DoC can be obtained via the company hotline.
Version: 03.02.2004
A3 1 0 0 8 - A1 0 0 - B1 0 1 - 1 - 5 8 1 9
Issued by
Information and Communication mobile
Haidenauplatz 1
D-81667 München
© Siemens AG 2004
All rights reserved. Subject to availability.
Right of modification reserved.
Printed in Germany (02/2004).
Siemens Aktiengesellschaft http://www.siemens.com/gigaset
Order no.: A31008-A100-B101-1-5819
Version: 03.02.2004
advertisement
Related manuals
advertisement
Table of contents
- 1 ENGLISH
- 2 Brief overview
- 2 Special displays
- 3 Safety information
- 4 Putting the telephone into service
- 5 Putting the telephone into service
- 6 Putting the telephone into service
- 7 Putting the telephone into service
- 8 Making calls
- 8 Making a call
- 8 Ending a call
- 8 Accepting a call
- 8 Redialling a number
- 9 Making calls
- 9 Saving/changing a call number (speed dialling)
- 9 Speed dialling
- 9 Cost-effective telephony
- 10 Cost-effective telephoning
- 10 Settings
- 10 Handset volume
- 10 Ringer volume
- 11 Settings
- 11 Ringtone
- 11 Keypad lock
- 11 Operating behind a PABX
- 12 Registering the handset manually
- 13 Tips
- 13 Maintenance
- 13 Contact with liquid
- 13 Troubleshooting
- 14 Range
- 14 Customer Care
- 17 FRANÇAIS