Silicon Labs UZB Reference Manual

es
ig
ns
Instruction
N
ew
D
UZB Product Manual
INS12713
Version:
10
Description:
Z-Wave USB Stick Reference Design
SAMBAT;GQUAT;JFR;BBR
2018-03-06
om
Date:
m
en
de
d
Written By:
fo
r
Document No.:
BBR;JFR;NTJ
Restrictions:
None
N
ot
R
ec
Reviewed By:
Approved by:
Date
CET
Initials Name
2018-03-06
09:27:05
NTJ
Justification
Niels Thybo Johansen
This document is the property of Silicon Labs. The data contained herein, in whole
or in part, may not be duplicated, used or disclosed outside the recipient for any
purpose. This restriction does not limit the recipient's right to use information
contained in the data if it is obtained from another source without restriction.
INS12713-10
UZB Product Manual
2018-03-06
1
2
3
4
20110824
20120223
20120522
20130205
SNA
SNA
SNA
SNA
WYNN
1
20130409
20130528
20130927
2
3
20131002
20131129
4
5
6
20150515
20150730
20151203
7
8
9
10
20160425
20160524
20161017
20180306
9,11
1,6
8
SNA
9
SNA
1
7
SNA
1, 5
SNA
1, 5
GQUAT Fig 1,3,4,6
4.1
9
SNA
1,9
SNA
1,9
JFR
Section 4.2
BBR
All
Brief description of changes
Created
Added USB info, corrected diagram caption
Added ANZ info, made RF/Electrical spec more generic
Changed to SD3503, opaque casing, no LEDs
Added Zniffer version
Measurements need to be reverified with updated tools and firmware for 500
Modified part #
Using Oracle p/n; changing template; updated references
G5, USB 1.1->2.0 low power; SDK 6.50->6.50.01; removed (TBC)s
Removed INF & refered to SDK
Added FCC & CE regulatory certification information
Added photo, & KR. Clarified firmware used. Move ordering info here.
Added JP, ANZ, KR regulatory certification information; USB certification
Added UZB2; Removed Korean certification; Added NVR info
Added UZB3; removed Korea from ordering
Revised Figure 1, 3, 4,6
Revised Section 4.1
Revised References
Fixed Table 1 error, Updated certification information
Remove EOL info; Updated regulatory regions
Added UZB3 certification number
Added Silicon Labs template
N
ot
R
ec
om
m
en
de
d
SNA
SNA
Pages
affected
ALL
1,2,5
4, 8
ALL
D
By
N
ew
Date
fo
r
Doc. Ver.
es
ig
ns
REVISION RECORD
silabs.com | Building a more connected world.
Page ii of iv
INS12713-10
UZB Product Manual
2018-03-06
es
ig
ns
Table of Contents
1
INTRODUCTION ...................................................................................................................................1
2
HARDWARE .........................................................................................................................................3
3
N
ew
D
2.1 Specific Components .........................................................................................................................4
2.2 Programming Test Points ...................................................................................................................4
2.3 NVR ....................................................................................................................................................5
2.4 RF .......................................................................................................................................................6
2.4.1
Matching and SAW Filter .........................................................................................................6
2.4.2
Antenna ....................................................................................................................................6
2.4.3
Specification .............................................................................................................................6
2.5 Electrical Specification .......................................................................................................................6
2.6 PCB ....................................................................................................................................................7
2.7 Casing ................................................................................................................................................7
SOFTWARE ..........................................................................................................................................8
fo
r
3.1 Firmware.............................................................................................................................................8
3.2 Installation ..........................................................................................................................................8
3.2.1
Windows 2000/XP/Vista/7/8 32 & 64 bit ..................................................................................8
3.2.2
Linux kernel 2.6.24+ .................................................................................................................8
3.2.3
MAC OS X 6.4 ..........................................................................................................................8
3.3 Application ..........................................................................................................................................8
CERTIFICATION ...................................................................................................................................9
4.1
4.2
4.3
4.4
Regulatory Compliance ......................................................................................................................9
Z-Wave Plus Certification ...................................................................................................................9
Z-Wave QFN ....................................................................................................................................10
USB Certification ..............................................................................................................................10
m
en
de
d
4
om
REFERENCES ...........................................................................................................................................11
Table of Figures
N
ot
R
ec
Figure 1: UZB .............................................................................................................................................. 1
Figure 2: Block Diagram .............................................................................................................................. 3
Figure 3: PCBA top view ............................................................................................................................. 3
Figure 4: PCBA bottom view ....................................................................................................................... 3
Figure 5: PCB Stack Up .............................................................................................................................. 7
Figure 6: PCB dimensions ........................................................................................................................... 7
Table of Tables
Table 1: Hardware Revisions ...................................................................................................................... 1
Table 2: Ordering Information ...................................................................................................................... 2
Table 3: Components .................................................................................................................................. 4
Table 4: Test Points ..................................................................................................................................... 4
Table 5: UZB3-E SD3503 NVR0 ................................................................................................................. 5
silabs.com | Building a more connected world.
Page iii of iv
INS12713-10
UZB Product Manual
2018-03-06
N
ot
R
ec
om
m
en
de
d
fo
r
N
ew
D
es
ig
ns
Table 6: UZB3-U/H SD3503 NVR0 SAW values ......................................................................................... 5
Table 7: UZB Revision 1 & 2 SD3503 NVR0 SAW values .......................................................................... 5
Table 8: RF Specifications ........................................................................................................................... 6
Table 9: Absolute Maximum Ratings ........................................................................................................... 6
Table 10 : Regulatory Compliance .............................................................................................................. 9
Table 11: Z-Wave Certification .................................................................................................................... 9
Table 12: Z-Wave QFN.............................................................................................................................. 10
Table 13: USB Certification ....................................................................................................................... 10
silabs.com | Building a more connected world.
Page iv of iv
INS12713-10
UZB Product Manual
2018-03-06
1 INTRODUCTION
D
es
ig
ns
The UZB is a USB v2.0 full speed low power CDC-ACM compliant Z-Wave adapter in a thumb drive form
factor.
N
ew
Figure 1: UZB
There are 3 revisions of hardware with slight differences in hardware.
Table 1: Hardware Revisions
Flash
SAW
UZB
M25PE10 (1Mb)
SF1010-01/02/03-SX (4-pin)
UZB2
M25PE20 (2Mb)
SF1010-01/02/03-SX (4-pin)
UZB3
M25PE20 (2Mb)
SF1256-908/923-02, SF1256-867-04 (5-pin)
m
en
de
d
fo
r
Label
N
ot
R
ec
om
It is available in the following flavors, labeled accordingly on the casing:
silabs.com | Building a more connected world.
Page 1 of 11
INS12713-10
UZB Product Manual
2018-03-06
Table 2: Ordering Information
Part Number
Label
UZB-S
ACC-UZB-S
Z-Wave Sniffer
Purpose
Region
Z-Wave Sniffer
PN:ACC-UZB-S
UZB S
UZB-E
ACC-UZB-E
Z-Wave Static Controller
UZB EU
ACC-UZB-U
Z-Wave Static Controller
PN:ACC-UZB-U
UZB US
UZB-H
ACC-UZB-H
Z-Wave Static Controller
Z-Wave Static
Controller
US
Z-Wave Static
Controller
Japan,
fo
r
PN:ACC-UZB-H
UZB JP
ACC-UZB-S
Z-Wave Sniffer
Z-Wave Sniffer
Hong Kong,
Australia/New Zealand
Any
m
en
de
d
UZB-S
Europe
N
ew
UZB-U
Any
D
PN:ACC-UZB-E
Z-Wave Static
Controller
es
ig
ns
Name
PN:ACC-UZB-S
UZB S
UZB in the part number & label is modified according to the revision. The UZB2/3 version with an
additional ‘–BRG’ suffix will contain a Bridge Controller instead of the Static Controller.
N
ot
R
ec
om
This document describes the hardware and software features of this reference design.
silabs.com | Building a more connected world.
Page 2 of 11
INS12713-10
UZB Product Manual
2018-03-06
2 HARDWARE
USB
Conn
VBUS
es
ig
ns
The UZB uses a relatively simple 4-Layer PCB design as shown in the block and PCBA diagrams below.
XOSCQ1,2
3.3V
LDO
SD3503
USB DP/DM
D
RF Matching
Passive Filter
SAW Filter
nRST, UART
P0.4
N
ew
Programmer
Test Points
32MHz
XTAL
Serial Flash
Antenna
m
en
de
d
fo
r
Figure 2: Block Diagram
N
ot
R
ec
om
Figure 3: PCBA top view
Figure 4: PCBA bottom view
silabs.com | Building a more connected world.
Page 3 of 11
INS12713-10
2.1
UZB Product Manual
2018-03-06
Specific Components
es
ig
ns
Some components which have specific designs purposes are described below.
Table 3: Components
Purpose
SD3503
MCU with code/data memory and Z-Wave transceiver running the firmware
LDO
Step down 5V to 3.3V for SD3503 MCU
Serial Flash
Node & routing information storage. Connected via SPI to MCU
N
ew
2.2
D
Component
Programming Test Points
Table 4: Test Points
Test Points
Description
VDD
3.3V Supply
GND
Ground
R
UART RX
T
UART TX
RST
Reset
VBUS
USB 5V VBUS
M
USB D-
P
USB D+
N
ot
R
ec
om
m
en
de
d
fo
r
The SD3503’s Flash is programmed prior to assembly via a test jig to access the programming test
points. The diagram below depicts the location of the test points for UART programming port that can be
connected to an external level shifter.
silabs.com | Building a more connected world.
Page 4 of 11
INS12713-10
2.3
UZB Product Manual
2018-03-06
NVR
Table 5: UZB3-E SD3503 NVR0
0
01
FF
00
1
FF
FF
FF
2
00
FF
FF
3
15
FF
FF
4
0D
FF
FF
5
3C
FF
FF
6
AC
FF
FF
7
03
FF
FF
8
02
FF
FF
9
01
FF
FF
A
00
FF
FF
B
01
FF
FF
C
00
FF
FF
D
FF
06
FF
E
FF
58
FF
F
FF
02
FF
D
Offset
10
20
30
es
ig
ns
The SD3503 also contains non volatile RAM, NVR0, which is programmed at factory and not part of the
firmware upgrade – see Ref [3]. The contents are 0xFF except for the addresses 0x10 to 0x30, with the
contents in hex as shown below.
N
ew
UZB revision 1 will have “00 80” instead of “01 00” at offset 0x19-0x1A owing to doubling of Serial Flash
size. The other flavors are different at addresses 0x14 to 0x17 to account for the different SAW used.
Table 6: UZB3-U/H SD3503 NVR0 SAW values
14
0D
0E
15
F6
19
16
38
60
17
0D
04
fo
r
Type\Offset
UZB3-U
UZB3-H
Table 7: UZB Revision 1 & 2 SD3503 NVR0 SAW values
14
0D
0D
0E
15
40
DC
17
16
44
84
6C
17
19
19
09
N
ot
R
ec
om
m
en
de
d
Type\Offset
UZB-E
UZB-U
UZB-H
silabs.com | Building a more connected world.
Page 5 of 11
INS12713-10
2.4
UZB Product Manual
2018-03-06
RF
2.4.1
es
ig
ns
SAW, matching components and antenna can be varied to support different regions.
Matching and SAW Filter
A Pi Low pass filter is incorporated to match the impedance of Helix Antenna; as well as reducing
emission of high frequency noise, if any. The use of SAW filter is required to achieve optimal RF
performance.
Antenna
D
2.4.2
2.4.3
Specification
N
ew
The same helix antenna is used to achieve a relatively compact size and cost for all regions.
Table 8: RF Specifications
Description
Typical RF receiver sensitivity
9.6kbps: -104dBm
RF Output Power
+2.5 dBm @ PA32
fo
r
RF
100kbps: -94dBm
m
en
de
d
40kbps: -99dBm
Range (typical)
Indoor >30 meters line of sight, in unobstructed environment
2.5
Electrical Specification
The “Absolute Maximum Ratings” specifies the conditions in which the UZB is guaranteed not to be
damaged but correct operations are not guaranteed.
om
Table 9: Absolute Maximum Ratings
Value
Storage Temperature
-40 – 85°C
Voltage on input pins (USB D+ / D-)
-0.3V to ‘+3.3V’ +0.3V
Minimum Operating Voltage (USB VBUS supply)
-0.3V
Maximum Operating Voltage (USB VBUS supply)
6V
Operating Temperature
-30 – 80°C
N
ot
R
ec
Electrical
The typical current consumption of UZB is 30mA (TBC).
silabs.com | Building a more connected world.
Page 6 of 11
INS12713-10
2.6
UZB Product Manual
2018-03-06
PCB
D
es
ig
ns
The PCB is a 4-layer FR4 design with a standard thickness of 0.8mm and stacked up as shown below.
om
m
en
de
d
fo
r
Its dimensions of 38.10x16mm are shown below.
N
ew
Figure 5: PCB Stack Up
Figure 6: PCB dimensions
ec
The area reserved for the antenna is approximately 12.9 mm x 16mm. The additional bar at the end of
the board of ~ 2.43mm x 16mm is to allow a better fit of the board to the off-shelf USB casing.
Casing
N
ot
R
2.7
The UZB is enclosed with an off-the-shelf USB casing (PN 180804), measuring 45.72mm x 20.32mm x
10.16mm, from New Age Enclosures at
http://www.newageenclosures.com/cart.php?m=product_detail&p=1&c=5 .
The UZB-S casing is black while the rest are white.
silabs.com | Building a more connected world.
Page 7 of 11
INS12713-10
UZB Product Manual
2018-03-06
3 SOFTWARE
Firmware
es
ig
ns
3.1
The device is preprogrammed with the 500 series Z-Wave Developer’s Kit Serial API Static Controller for
ZM5304 USB firmware as required. The firmware can be upgraded via USB using the Z-Wave PC
Programmer tool. Both the firmware and the programmer tools will be available in the Z-Wave SDK.
Installation
D
3.2
3.2.1
Windows 2000/XP/Vista/7/8 32 & 64 bit
N
ew
As the device exports a USB CDC/ACM class compliant interface, it appears as a serial port, reusing
existing standard drivers on most popular PC operating systems. As such there is no vendor driver
required.
fo
r
UZB.INF & UZB.CAT are provided in the Z-Wave SDK that reuses the standard Windows usbser.sys or
usbser64.sys driver. The device appears in the Device Manager under the Ports section, and is
accessible through the Windows CreateFile API by applications as “//.//COMxxx” where xxx is the COM
Port number assigned by the OS.
Linux kernel 2.6.24+
m
en
de
d
3.2.2
The device appears as “/dev/ttyACMxx” where xxx is the tty number assigned by the OS.
3.2.3
MAC OS X 6.4
The device appears as “/dev/tty.usbmodemxxx” where xxx is the tty number assigned by the OS.
Application
om
3.3
N
ot
R
ec
Z-Wave Zniffer and PC Controller applications are supported by UZB-S and UZBs respectively but these
applications only run on Windows.
silabs.com | Building a more connected world.
Page 8 of 11
INS12713-10
UZB Product Manual
2018-03-06
4.1
Regulatory Compliance
Table 10 : Regulatory Compliance
es
ig
ns
4 CERTIFICATION
Part
Region(s)
ACC-UZB3-E
CE (Europe) - EN 300 220-1/2, 301 489-1/3, 55022, 61000-4-2/3, 62479, 60950-1;
D
Mauritius; Morocco; Armenia, Egypt; Jordan; Kazakhstan; Yemen; Libya; Qatar;
N
ew
Saudi Arabia;
FCC (US) - CFR 47 Part 15 Subparts B & C
ACC-UZB3-H
MIC (Japan) - ARIB STD-T108
ACC-UZB-H
ACMA (AS/NZ) - CISPR 22 & AS/NZS 4268;
MIC (Japan);
fo
r
ACC-UZB3-U
Costa Rica; El Salvador; Paraguay; Peru; Uruguay
CE (Europe);
m
en
de
d
ACC-UZB-E
Indonesia
ACC-UZB-U
FCC (US);
Bahamas; Barbados; Bermuda; Bolivia; Cayman Islands; Chile; Columbia;
Ecuador; Guatemala; Haiti; Honduras; Jamaica; Mexico; Nicaragua; Panama;
Z-Wave Plus Certification
ec
4.2
om
St. Kitts & Nevis; Suriname; Trinidad & Tobago; Turks & Caicos
ot
R
Part
Document
ZC10-16065114
N
ACC-UZB3-E
Table 11: Z-Wave Certification
silabs.com | Building a more connected world.
Page 9 of 11
INS12713-10
4.3
UZB Product Manual
2018-03-06
Z-Wave QFN
Document
ACC-UZB3-U
CEF19693
ACC-UZB3-E
CEF19695
ACC-UZB3-H
CEF19694
4.4
N
ew
D
Part
es
ig
ns
Table 12: Z-Wave QFN
USB Certification
USB Test ID (TID)
ACC-UZB
10007151
N
ot
R
ec
om
m
en
de
d
Part
fo
r
Table 13: USB Certification
silabs.com | Building a more connected world.
Page 10 of 11
INS12713-10
UZB Product Manual
2018-03-06
REFERENCES
N
ew
D
es
ig
ns
Silicon Labs, INS12308, Instruction, Z-Wave 500 Series Application Programming Guide
Silicon Labs, DSH12469, Datasheet, SD3503
Silicon Labs, SDS12467, S/W Design Spec, 500 Series NVR Content
Silicon Labs, INS10249, Instruction, Zniffer User Guide
Silicon Labs, INS10240, Instruction, PC Controller User Guide
Silicon Labs, INS10679, Instruction, PC Programmer User Guide
Silicon Labs, SCH13396, Schematic, UZB3
Silicon Labs, PCB13397, UZB3 PCB
Silicon Labs, BOM13395, BOM, UZB3-H
Silicon Labs, BOM13394, BOM, UZB3-U
Silicon Labs, BOM13393, BOM, UZB3-E
Silicon Labs, BOM13463, BOM, UZB3-S
Silicon Labs, DSH11697, Datasheet, UZB Helix Antenna
N
ot
R
ec
om
m
en
de
d
fo
r
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10]
[11]
[12]
[13]
silabs.com | Building a more connected world.
Page 11 of 11
es
ig
ns
D
N
ew
fo
r
om
Products
m
en
de
d
Smart.
Connected.
Energy-Friendly.
www.silabs.com/products
Quality
www.silabs.com/quality
Support and Community
community.silabs.com
N
ot
R
ec
Disclaimer
Silicon Labs intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or
intending to use the Silicon Labs products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical"
parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Labs reserves the right to make changes
without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included
information. Silicon Labs shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses granted
hereunder to design or fabricate any integrated circuits. The products are not designed or authorized to be used within any Life Support System without the specific written consent of
Silicon Labs. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant
personal injury or death. Silicon Labs products are not designed or authorized for military applications. Silicon Labs products shall under no circumstances be used in weapons of mass
destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.
Trademark Information
Silicon Laboratories Inc.® , Silicon Laboratories®, Silicon Labs®, SiLabs® and the Silicon Labs logo®, Bluegiga®, Bluegiga Logo®, Clockbuilder®, CMEMS®, DSPLL®, EFM®,
EFM32®, EFR, Ember®, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZRadio®, EZRadioPRO®,
Gecko®, ISOmodem®, Micrium, Precision32®, ProSLIC®, Simplicity Studio®, SiPHY®, Telegesis, the Telegesis Logo®, USBXpress®, Zentri, Z-Wave and others are trademarks or
registered trademarks of Silicon Labs. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited.
All other products or brand names mentioned herein are trademarks of their respective holders.
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
USA
http://www.silabs.com
">