Infinix
SMART 9
X6532 User Manual
(D&E&I&J&N&O)
Exploded diagram specification
1
1
3
5
7
9
11
13
15
2
4
6
8
10
12
14
16
FRONT FLASH BLACKOUT MYRA
HEAT SINK
CONDUCTIVE FOAM 1
SIM CARD
SEAL SILICONE SLEEVE
FRONT DUST FOAM
BACK ADHESIVE
FRONT FLASH HOOD
18
20
22
24
26
28
LIGHT SENSING GUIDE
FPC HANDSET SPEAKER
SHIELD SHIELD COPPER FOIL
SIDE KEY FPC
REAR SHOT
MOTHERBOARD
29
31
33
35
37
TP
LIGHT BLACKOUT MYRA
SEALING FOAM
CONDUCTIVE FOAM 2
SEALING SILICONE SHEET
FACE SHELL
BACK ADHESIVE
SHIELD CONDUCTIVE SPONGE
A
GROUNDING FOAM
BATTERY ADHESIVE 1
GROUNDING COPPER FOIL
FRONT SHOT
COAXIAL LINE
LIGHT SENSITIVE SILICONE
CASE
WATERPROOF SUPPORT FOAM
WATERPROOF FILM
GROUNDING COPPER FOIL
SHIELD SHIELD COPPER FOIL
GROUNDING SPONGE 2
30
32
34
36
38
GROUNDING CONDUCTIVE CLOTH
BACK CAMERA
PRE-COMPRESSION FOAM
GROUNDING SPONGE 1
SINGLE HEAT SINK INSIDE
39
41
43
45
47
WATERPROOF SEALING FOAM
COMPACT FOAM
WIFI ANTENNA FPC
REAR FLASHING FPC
FLASH LAMP SHADE
40
42
44
46
48
49
51
53
55
FLASH COVER BACK ADHESIVE
AUXILIARY SEALING FOAM
SIDE FINGERPRINT MODULE
UPPER HORN HEAT SINK
50
52
54
56
57
59
61
63
65
67
69
71
BATTERY COVER
REAR LENS BACK ADHESIVE
CAMERA TRIM
MAIN LENS
LOWER HORN HEAT SINK
HORN CONDUCTIVE FOAM
LOWER SPEAKER AIR FILTER
SEALING FOAM
58
60
62
64
66
68
70
72
COMPACT FOAM
ANT1 FPC
UPPER SPEAKER AIR FILTER
REAR FLASH LAMP SHADE
REAR FLASH COVER BACK
ADHESIVE
MAIN SHOT SEALING FOAM
SIDE KEY COMPONENTS
MIDDLE FRAME
BATTERY COVER BACKED WITH
ADHESIVE
FLASH LENS BACK ADHESIVE
17
19
21
23
25
27
2
SEALING ADHENSIVE
PHOTONIC FLASH LENS
AUXILIARY LENS
SCREWS
LOWER SPEAKER FPC
ANT0 DIVERSITY ANTENNA FPC
BATTERY
73
75
77
79
81
83
85
87
TYPE-C SEALED SILICONE
SLEEVE
SEAL SILICONE SLEEVE
SHRAPNEL SPEAKER
FRONT HORN CAVITY SEAL
FOAM
MIC SEALING FOAM
74
SMALL BOARD
76
78
80
HEADSET SEAT MYRA
SEAL SILICONE SLEEVE
SCREEN SHIELDED COPPER
FOIL
84
86
MOTOR
BATTERY IS EASY TO GLUE
USB GROUND CONDUCTIVE
CLOTH
SCREEN FPC CONDUCTIVE
ADHESIVE
FPC BACK ADHESIVE
SEALED SILICONE SLEEVE
82
Know your phone
3
1. Front camera
2. Volume + button
3. Volume - button
4. Power button & side fingerprint sensor
SIM/SD card installation
1. Power off your phone.
2. Refer to the following picture for SIM/SD card
4
installation.
Charging the phone
You can charge your phone with a charger or by
connecting it to a computer using a USB cable (comes
1
with the phone).
Use only Infinix chargers and cables. Other chargers or
cables may damage the phone and invalidate its warranty.
2
FCC Caution
1. This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
Information to the user.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) information:
This mobile phone meets the government's requirements for exposure to
radio waves. The guidelines are based on standards that were developed by
independent scientific organizations through periodic and thorough
evaluation of scientific studies. The standards include a substantial safety
margin designed to assure the safety of all persons regardless of age or
health.
FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is
1.6 W/kg averaged over one gram of tissue. Device types: X6532 (FCC ID:
2AIZN-YYS-X6532) has also been tested against this SAR limit. The highest
SAR value reported under this standard during product certification for use
at the ear is 1.178 W/kg and when properly worn on the body is
3
0.566W/kg.
Body-worn Operation
This device was tested for typical body-worn operations. To
comply with RF exposure requirements, a minimum separation
distance of 1.0cm must be maintained between the user’s body and
the handset, including the antenna. Third-party belt-clips, holsters,
and similar accessories used by this device should not contain any
metallic components. Body-worn accessories that do not meet these
requirements may not comply with RF exposure requirements and
should be avoided. Use only the supplied or an approved antenna.
For DTS patents, see http://patents.dts.com. Manufactured under
license from DTS Licensing Limited. DTS, the Symbol, & DTS and the
Symbol together are registered trademarks or trademarks of DTS, Inc.
in the United States and/or other countries. © DTS, Inc. All Rights
Reserved.
Operating System: AndroidTM
Android is a trademark of Google LLC.
4
">
