Hotpoint BS89EK Operating instructions

Operating Instructions
OVEN
Contents
GB
English,1
FI
Suomi, 37
DK
Dansk, 13
SE
Svenska, 49
NO
Norsk,25
Installation, 2-3
Positioning
Electrical connection
Technical data
Description of the appliance, 4
Overall view
Control panel
Display
Start-up and use, 5
Setting the clock
Setting the timer
Starting the oven
Cooking modes, 6-8
FZ 891 P.1 IX
FZ 891 P.1 IX AUS
Cooking modes
Programming cooking
Practical cooking advice
Cooking advice table
Precautions and tips, 9
General safety
Disposal
Respecting and conserving the environment
Care and maintenance, 10-11
Switching the appliance off
Cleaning the appliance
Cleaning the oven door
Replacing the light bulb
Automatic cleaning using the FAST CLEAN function
Assistance, 12
/*
Installation
! Before operating your new appliance please read
this instruction booklet carefully. It contains
important information concerning the safe operation,
installation and maintenance of the appliance.
! Please keep these operating instructions for future
reference. Pass them on to possible new owners of
the appliance.
Ventilation
To ensure adequate ventilation is provided, the back
panel of the cabinet must be removed. It is
advisable to install the oven so that it rests on two
strips of wood, or on a completely flat surface with
an opening of at least 45 x 560 mm (see diagrams).
Positioning
.
! Keep packaging material out of the reach of
children.
It can become a choking or suffocation hazard. (see
Precautions and tips).
! The appliance must be installed by a qualified
professional in accordance with the instructions
provided. Incorrect installation may cause harm to
people and animals or may damage property.
Built-in appliance
Use the appropriate cabinet to ensure that the
appliance functions properly.
• The panels adjacent to the oven must be made of
heat-resistant material.
560
mm
45 m
m.
Centring and fixing
Position the 4 tabs on the side of the oven, in line
with the 4 holes on the outer frame. Adjust the tabs
according to the thickness of the cabinet side panel,
as shown below:
20 mm thick: take off the
removable part of the tab
(see diagram).
• Cabinets with a veneer exterior must be
assembled with glues which can withstand
temperatures of up to 100°C.
m.
45 m
mm
.
18 mm thick: use the first
groove, which has already
been set in the factory
(see diagram).
16 mm thick: use the second
groove (see diagram).
5 mm.
567 mm.
558
593 mm.
23 mm.
• to install the oven under the counter (see diagram)
or in a kitchen unit, the cabinet must have the
following dimensions:
595 mm.
/*
595
.
mm
.
545
mm
m.
m
24
! The appliance must not come into contact with
electrical parts once it has been installed.
The indications for consumption given on the data
plate have been calculated for this type of
installation.
Secure the appliance to the cabinet by opening the
oven door and inserting 4 screws into the 4 holes on
the outer frame.
! All parts which ensure the safe operation of the
appliance must not be removable without the aid of
a tool.
Electrical connection
! Ovens equipped with a three-pole power supply
cable are designed to operate with alternating
current at the voltage and frequency indicated on
the data plate located on the appliance (see below).
Fitting the power supply cable
1. Open the terminal
board by inserting a
screwdriver into the
side tabs of the cover.
Use the screwdriver as
a lever by pushing it
down to open the cover
(see diagram).
2. Install the power
supply cable by
loosening the cable
clamp screw and the
three wire contact
screws L-N- .
Connect the wires to
the corresponding
terminals: the Blue wire
N L
to the terminal marked
(N), the Brown wire to
the terminal marked (L) and the Yellow/Green wire to
(see diagram).
the terminal marked
3. Secure the cable by fastening the clamp screw.
4. Close the cover of the terminal board.
• The socket can withstand the maximum power of
the appliance, which is indicated on the data
plate (see below).
/*
• The voltage is in the range between the values
indicated on the data plate (see below).
• The socket is compatible with the plug of the
appliance. If the socket is incompatible with the
plug, ask an authorised technician to replace it.
Do not use extension cords or multiple sockets.
! Once the appliance has been installed, the power
supply cable and the electrical socket must be
easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced
by authorised technicians only (see Assistance).
! The manufacturer declines any liability should
these safety measures not be observed.
width 43.5 cm
height 32 cm
depth 40 cm
56 l
voltage: 220 - 240 V~ 50/60Hz
maximum power absorbed 2800 W
Connecting the electricity supply cable to the mains
Install a standardised plug corresponding to the load
indicated on the data plate (see table).
The appliance must be directly connected to the mains
using an omnipolar switch with a minimum contact
opening of 3 mm installed between the appliance and
the mains. The switch must be suitable for the charge
indicated and must comply with current electrical
regulations (the earthing wire must not be interrupted
by the switch). The supply cable must be positioned
so that it does not come into contact with temperatures
higher than 50°C at any point.
! The installer must ensure that the correct electrical
connection has been made and that it is fully
compliant with safety regulations.
Before connecting the appliance to the power
supply, make sure that:
• The appliance is earthed and the plug is compliant
with the law.
Directive 2002/40/EC on the label of
electric ovens. Standard EN 50304
Energy consumption for Natural
convection – heating mode:
Traditional mode
Declared energy consumption for
Forced convection Class – heating
mode:
Baking
This appliance conforms to the
following European Economic
Community directives: 73/23/EEC
dated 19/02/73 (Low Voltage) and
subsequent amendments 89/336/EEC dated 03/05/89
(Electromagnetic Compatibility) and
subsequent amendments 93/68/EEC dated 22/07/93 and
subsequent amendments.
2002/96/EC
!
Description
of the appliance
/*
Overall view
GUIDES for the
sliding racks
Control panel
position 5
position 4
position 3
position 2
position 1
GRILL
DRIPPING PAN
Control panel
DISPLAY
SELECTOR
Knob
FAST CLEAN
button
THERMOSTAT
knob
TIME SETTING
button
TIMER
knob
Display
TEMPERATURE
and TIME digits
Preheating
indicator
CLOCK
icon
STOP
icon
END OF COOKING
icon
DOOR LOCK
indicator
TIMER
icon
"
DURATION
icon
Start-up and use
! The first time you use your appliance, heat the
empty oven with its door closed at its maximum
temperature for at least half an hour. Ensure that the
room is well ventilated before switching the oven off
and opening the oven door. The appliance may emit
a slightly unpleasant odour caused by protective
substances used during the manufacturing process
burning away.
Setting the clock
The clock may be set when the oven is switched
off or when it is switched on, provided that a the end
time of a cooking cycle has not been programmed
previously.
button several times until the
1. Press the
icon and the first two digits on the display start to flash.
2. Turn the TIMER KNOB towards “+” and “-” to
adjust the hour value.
button again until the other two
3. Press the
digits on the DISPLAY begin to flash.
4. Turn the TIMER KNOB towards “+” and “-” to
adjust the minute value.
5. Press the
button again to confirm.
Setting the timer
This function does not interrupt cooking and does
not affect the oven; it is simply used to activate the
buzzer when the set amount of time has elapsed.
button several times until the
1. Press the
icon and the three digits on the display begin to
flash.
2. Turn the TIMER KNOB towards “+” and “-” to
adjust the minute value.
button again to confirm.
3. Press the
The display will then show the time as it counts
down. When this period of time has elapsed the
buzzer will be activated.
Starting the oven
1. Select the desired cooking mode by turning the
SELECTOR knob.
2. The oven begins its preheating stage and the
preheating indicator lights up.
The temperature may be changed by turning the
THERMOSTAT knob
complete: you may now place the food in the oven.
4. During cooking it is always possible to:
- change the cooking mode by turning the
SELECTOR knob
- change the temperature by turning the
THERMOSTAT knob
- set the cooking duration in addition to the cooking
end time
(see Cooking modes)
- stop cooking by turning the SELECTOR knob to the
“0” position.
5. The oven switches off automatically after two
hours: this default period of time is set for all
cooking modes for safety reasons.
The cooking duration may be changed
(see Cooking modes).
6. If a blackout occurs while the oven is already in
operation, an automatic system within the appliance
will reactivate the cooking mode from where it was
interrupted as long as the temperature has not
dropped below a certain level. Programmed cooking
modes which have not started will not be restored
and must be reprogrammed.
! There is no preheating stage for the FAST
COOKING and BARBECUE modes.
! Never put objects directly on the bottom of the
oven; this will avoid the enamel coating being
damaged.
! Always place cookware on the rack(s) provided.
Cooling ventilation
In order to cool down the external temperature of the
oven, a cooling fan blows a stream of air between
the control panel and the oven door. In the FAST
COOKING mode, the fan is activated automatically
after ten minutes. In the BAKING mode, the cooling
fan is only activated when the oven is hot. At the
beginning of the FAST CLEAN mode, the cooling fan
operates at low speed.
! Once cooking has been completed, the cooling fan
continues to operate until the oven has cooled down
sufficiently.
Oven light
When the oven is not in operation, the lamp can be
switched on at any time by opening the oven door.
switches off
3. When the preheating indicator
and a buzzer sounds the preheating process is
#
/*
Cooking modes
/*
Cooking modes
! All cooking modes have a default cooking
temperature which may be adjusted manually
between 40°C and 250°C as desired.
In the BARBECUE mode, the default power level
value is indicated as a percentage (%) and may also
be adjusted manually.
TRADITIONAL OVEN mode
When using this traditional cooking mode, it is best
to use one cooking rack only. if more than one rack
is used, the heat will be distributed unevenly.
MULTI-COOKING mode
FAST COOKING mode
Preheating is not necessary for this cooking mode.
This mode is particularly suitable for cooking prepacked food quickly (frozen or pre-cooked). The
best results are achieved using one cooking rack
only.
PROVING mode
The oven reaches and maintains a temperature of
40°C irrespective of the position of the
THERMOSTAT knob. This mode is ideal for
leavening dough made with yeast.
Spit roast (only available in certain models)
Since the heat remains constant throughout the
oven, the air cooks and browns food in a uniform
manner. A maximum of two racks may be used at
the same time.
To operate the spit roast
function (see diagram)
proceed as follows:
BARBECUE mode
By turning the THERMOSTAT knob, the different
power levels which may be set will appear on the
display; these range between 50% and 100%. The
high and direct temperature of the grill is
recommended for food which requires a high surface
temperature. Always cook in this mode with the oven
door closed.
GRATIN mode
This combination of features increases the
effectiveness of the unidirectional thermal radiation
provided by the heating elements through forced
circulation of the air throughout the oven.
This helps prevent food from burning on the surface
and allows the heat to penetrate right into the food.
Always cook in this mode with the oven door closed.
PIZZA OVEN mode
This combination heats the oven rapidly by producing
a considerable amount of heat, particularly from the
element at the bottom. If you use more than one rack
at a time, switch the position of the dishes halfway
through the cooking process.
BAKING mode
This mode is ideal for baking temperature sensitive
foods (such as cakes, which need to rise) and for
the preparation of “bitesize pastries” on 3 shelves
simultaneously.
$
1. Place the dripping pan in position 1.
2. Place the rotisserie support in position 3 and
insert the spit in the hole provided on the back panel
of the oven.
3. Start the rotisserie using the SELECTOR knob to
select mode
or
.
mode is activated, the spit will stop if
! When the
the door is opened.
Programming cooking
Practical cooking advice
A cooking mode must be selected before
programming can take place.
! Do not place racks in position 1 and 5 during fanassisted cooking. This is because excessive direct
heat can burn temperature sensitive foods.
Programming the cooking duration
1. Press the
button several times until the
icon and the three digits on the DISPLAY begin to
flash.
2. Turn the TIMER KNOB towards “+” and “-” to
adjust the duration.
button again to confirm.
3. Press the
4. When the set time has elapsed, the text END
appears on the DISPLAY, the oven will stop cooking
and a buzzer sounds.
• For example: it is 9:00 a.m. and a time of 1 hour
and 15 minutes is programmed. The programme
will stop automatically at 10:15 a.m.
Setting the end time for a cooking mode
A cooking duration must be set before the end
cooking time can be scheduled.
1. Follow steps 1 to 3 to set the duration as detailed
above.
button until the
icon and
2. Next, press the
the two digits on the DISPLAY begin to flash.
3. Turn the TIMER KNOB towards “+” and “-” to
adjust the hour value.
button again until the other two
4. Press the
digits on the DISPLAY begin to flash.
5. Turn the TIMER KNOB towards “+” and “-” to
adjust the minute value.
button again to confirm.
6. Press the
7. When the set time has elapsed, the text END
appears on the DISPLAY, the oven will stop cooking
and a buzzer sounds.
and
Programming has been set when the
buttons are illuminated. The DISPLAY shows the
cooking end time and the cooking duration
alternately.
To cancel programming, turn the SELECTOR knob to
the “0” position.
/*
! In the BARBECUE and GRATIN cooking modes,
particularly when using the rotisserie spit, place the
dripping pan in position 1 to collect cooking
residues (fat and/or grease).
MULTI-COOKING
• Use positions 2 and 4, placing the food which
requires more heat on 2.
• Place the dripping pan on the bottom and the rack
on top.
BARBECUE
• Place the rack in position 3 or 4. Position the food
in the centre of the rack.
• We recommend that the power level is set to
maximum. The top heating element is regulated
by a thermostat and may not always operate
constantly.
PIZZA OVEN
• Use a light aluminium pizza pan. Place it on the
rack provided.
For a crispy crust, do not use the dripping pan as
it prevents the crust from forming by extending
the total cooking time.
• If the pizza has a lot of toppings, we recommend
adding the mozzarella cheese on top of the pizza
halfway through the cooking process.
%
/*
Cooking advice table
&RRNLQJ
PRGHV
&RQYHFWLRQ
2YHQ
0XOWLFRRNLQJ
%DUEHFXH
*UDWLQ
3L]]D 2YHQ
%DNLQJ PRGH
)DVW FRRNLQJ
)RRGV
Duck
Chicken
Roast veal or beef
Roast pork
Biscuits (shortcrust pastry)
Pies / Tarts
Pizza on 2 racks
Pies on two racks/cakes on 2 racks
Sponge cake on 2 racks (on the dripping pan)
Roast chicken + potatoes
Lamb
Mackerel
Lasagne
Cream puffs on 2 racks
Biscuits on 2 racks
Cheese puffs on 2 racks
Savoury pies
Mackerel
Sole and cuttlefish
Squid and prawn kebabs
Cod fillet
Grilled vegetables
Veal steak
Sausages
Hamburgers
Toasted sandwiches (or toast)
Spit-roast chicken using rotisserie spit (where
present)
Spit-roast lamb using rotisserie spit (where present)
Grilled chicken
Cuttlefish
Spit-roast chicken using rotisserie spit (where
present)
Spit-roast duck using rotisserie spit (where present)
Roast veal or beef
Roast pork
Lamb
Pizza
Focaccia bread
Pies / Tarts
Fruit cakes
Sponge cake made with yoghurt
Small cakes on 2 racks
Sponge cake
Cream puffs on 3 racks
Biscuits on 3 racks
Filled pancakes
Meringues on 3 racks
Cheese puffs
:HLJKW
LQ NJ
1.5
1.5
1
1
1
5DFN SRVLWLRQ
6WDQGDUG
6OLGLQJ
JXLGHUDLOV
JXLGHUDLOV
3UHKHDWLQJ
5HFRPPHQGHG
7HPSHUDWXUH
ƒ&
&RRNLQJ
GXUDWLRQ
PLQXWHV
1
0.7
0.7
0.7
0.5
0.8
0.7
4 or 5
4 or 6
1
2
2
2
2
2
2
2 and 4
2 and 4
2 and 4
1 and 2/3
2
1 or 2
2
2 and 4
2 and 4
2 and 4
1 and 3
4
4
4
4
3 or 4
4
4
4
4
-
1
1
1
1
1
1
1 and 3
1 and 3
1 and 3
1 and 3
1
1
1
1 and 3
1 and 3
1 and 3
1 and 3
3
3
3
3
2 or 3
3
3
3
3
-
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
No
200-210
200-210
200
200-210
180
180
220-230
180
170
200-210
190-200
180
190-200
190
190
210
200
100%
100%
100%
100%
100%
100%
100%
100%
100%
100%
70-80
60-70
70-75
70-80
15-20
30-35
20-25
30-35
20-25
65-75
45-50
30-35
35-40
20-25
10-20
20-25
20-30
15-20
10-15
8-10
10-15
15-20
15-20
15-20
10-12
3-5
70-80
1
1,5
1
1,5
2
2
-
2
2
-
No
No
No
No
100%
210
200
210
70-80
55-60
30-35
70-80
1,5
1
1
1
0.5
0.5
0.5
1
0.7
0.7
0.6
0.7
0.7
0.8
0.5
0.5
2
2
2
2
2
2 or 3
2 or 3
2 or 3
2 and 4
2 or 3
1, 3 and 5
1, 3 and 5
2
1, 3 and 5
2
2
2
2
1
1
1 or 2
1 or 2
1 or 2
1 and 3
1 or 2
1, 2 and 4
1, 2 and 4
1
1, 2 and 4
1
No
No
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
210
210
210
210
220
200
180
180
170-180
180-190
160-170
180-190
180
200
90
210
60-70
60-75
70-80
40-45
15-20
20-25
25-35
40-50
45-55
20-25
30-40
20-25
20-25
30-35
180
20-25
Pizza
Courgette and prawn pie
Country style spinach pie
Turnovers
Lasagne
Golden Rolls
Chicken bites
0.3
0.4
0.5
0.3
0.5
0.4
0.4
2
2
2
2
2
2
2
1
1
1
1
1
1
1
-
250
200
220
200
200
180
220
12
20
30-35
25
35
25-30
15-20
Golden chicken wings
0.4
2
1
-
200
20-25
1+1
1
1
1
)UR]HQ IRRG
3UHFRRNHG IRRG
)UHVK )RRG
0.3
2
1
200
15-18
Biscuits (shortcrust pastry)
0.6
2
1
180
45
Sponge cake made with yoghurt
0.2
2
1
210
10-12
Cheese puffs
3URYLQJ
Rising process for dough made with yeast (brioches,
2
1
40
30-60
bread, sugar pie, croissants, etc.)
! The cooking times listed above are intended as guidelines only and may be modified according to personal tastes. Oven preheating times are set as standard and may not be
modified manually.
&
Precautions and tips
! This appliance has been designed and
manufactured in compliance with international safety
standards. The following warnings are provided for
safety reasons and must be read carefully.
General safety
• The appliance was designed for domestic use
inside the home and is not intended for
commercial or industrial use.
• Never perform any cleaning or maintenance work
without having disconnected the appliance from
the electricity mains.
/*
• If the appliance breaks down, under no
circumstances should you attempt to perform the
repairs yourself. Repairs carried out by
inexperienced persons may cause injury or further
malfunctioning of the appliance. Contact a Service
Centre (see Assistance).
• Do not rest heavy objects on the open oven door.
• The appliance must not be installed outdoors, even
in covered areas. It is extremely dangerous to
leave the appliance exposed to rain and storms.
Disposal
• When moving or positioning the appliance, always
use the handles provided on the sides of the oven.
• When disposing of packaging material: observe local
legislation so that the packaging may be reused.
• Do not touch the appliance with bare feet or with
wet or damp hands and feet.
• Ensure that the power supply cables of other
electrical appliances do not come into contact
with the hot parts of the oven.
• The European Directive 2002/96/EC relating to
Waste Electrical and Electronic Equipment (WEEE)
states that household appliances should not be
disposed of using the normal solid urban waste
cycle. Exhausted appliances should be collected
separately in order to optimise the cost of re-using
and recycling the materials inside the machine,
while preventing potential damage to the
atmosphere and to public health. The crossed-out
dustbin is marked on all products to remind the
owner of their obligations regarding separated waste
collection. For further information relating to the
correct disposal of exhausted household
appliances, owners may contact the public service
provided or their local dealer.
• The openings used for the ventilation and
dispersion of heat must never be covered.
Respecting and conserving the
environment
• Always grip the oven door handle in the centre:
the ends may be hot.
• You can help to reduce the peak load of the
electricity supply network companies by using the
oven in the hours between late afternoon and the
early hours of the morning. The cooking mode
programming options, the “delayed cooking”
mode (see Cooking modes) and “delayed
automatic cleaning” mode (see Care and
Maintenance) in particular, enable the user to
organise their time efficiently.
• The appliance must be used by adults only for the
preparation of food, in accordance with the
instructions provided in this booklet.
• Do not touch the heating elements or certain
parts of the oven door when the appliance is in
use; these parts become extremely hot. Keep
children well away from the appliance.
• Always use oven gloves when placing cookware
in the oven or when removing it.
• Do not use aluminium foil to line the bottom of the oven.
• Do not place flammable materials in the oven: If
the appliance is switched on accidentally, the
materials could catch fire.
• Always make sure the knobs are in the “l”/“¡”
position when the appliance is not in use.
• When unplugging the appliance, always pull the plug
from the mains socket; do not pull on the cable.
• Always keep the oven door closed when using the
BARBECUE and GRATIN modes: This will achieve
improved results while saving energy
(approximately 10%).
• Check the door seals regularly and wipe them clean
to ensure they are free of debris so that they adhere
properly to the door, thus avoiding heat dispersion.
'
Care and maintenance
/*
Switching the appliance off
3. Grip the door on the two
external sides and close it
approximately half way. Pull
the door towards you, lifting it
out of its slot (see diagram).
Disconnect your appliance from the electricity
supply before carrying out any work on it.
Cleaning the appliance
• The stainless steel or enamel-coated external
parts and the rubber seals may be cleaned using
a sponge that has been soaked in lukewarm water
and neutral soap. Use specialised products for
the removal of stubborn stains. After cleaning,
rinse and dry thoroughly. Do not use abrasive
powders or corrosive substances.
• The inside of the oven should ideally be cleaned
after each use, while it is still lukewarm. Use hot
water and detergent, then rinse well and dry with
a soft cloth. Do not use abrasive products.
• The accessories can be washed like everyday
crockery, and are even dishwasher safe.
Never use steam cleaners or pressure cleaners on
the appliance.
To replace the door, reverse this sequence.
Inspecting the seals
Check the door seals around the oven periodically. If
the seals are damaged, please contact your nearest
After-sales Service Centre (see Assistance). We
recommend that the oven is not used until the seals
have been replaced.
Replacing the light bulb
To replace the oven light bulb:
Cleaning the oven door
Clean the glass part of the oven door using a
sponge and a non-abrasive cleaning product, then
dry thoroughly with a soft cloth. Do not use rough
abrasive material or sharp metal scrapers as these
could scratch the surface and cause the glass to
crack. For more thorough cleaning purposes, the
oven door may be removed:
1. Open the oven door fully
(see diagram).
2. Lift up and turn the small
levers located on the two
hinges (see diagram).
Oven
compartment
Lamp
Seal
Glass door
1. Remove the glass cover using a screwdriver.
2. Unscrew the light bulb and replace it with a
similar one: Wattage 15 W, cap E 14.
Replace the glass cover, making sure the seal is
positioned correctly (see diagram).
Automatic cleaning with the FAST
CLEAN function
With the FAST CLEAN mode, the internal
temperature of the oven reaches 500°C. The
pyrolytic cycle is activated, burning away food and
grime residues. Dirt is literally incinerated.
Keep children away from the appliance during the
automatic cleaning cycle as surfaces may become
very hot. Particles may ignite inside the oven due to
the combustion process. There is no cause for
concern: this process is both normal and hazardfree.
Before initiating the FAST CLEAN mode:
• Remove large or coarse food residues from the
inside of the oven using a damp sponge. Do not use
detergents.
• Remove all accessories.
• Do not place tea towels or pot holders over the
oven handle.
• Turn the SELECTOR knob to the “0” position.
! If the oven is too hot, the pyrolytic cycle may not
start. Wait for the oven to cool down.
! The programme may only be started once the oven
door has been closed.
To activate the FAST CLEAN cycle press and hold
button for approximately 4 seconds. The
the
TIMER KNOB may be used to select the desired
cleaning level; there are three default time settings
which cannot be modified.
1. Economy (ECO): turn the knob towards “-”.
Duration 1 hour.
2. Normal (NOR): initial level. Duration 1 hour and 30
minutes.
3. Intensive (INT): turn the knob towards “+”.
Duration 2 hours.
4. Press the
button to confirm.
An end time for the FAST CLEAN cycle (as for a
normal cooking cycle) may be programmed (see
Programming the automatic cleaning end time).
Safety devices
/*
icon on the display, when lit, indicates
• The
that the oven door was automatically locked as soon
as the temperature reached a high value.
• The
icon indicates that the cleaning cycle
may be cancelled at any time by pressing the
button.
• If a malfunction occurs, the heating elements will
be switched off.
• Once the oven door has been locked, you cannot
change the duration and cycle end time settings.
Programming the automatic cleaning end time
button until the
icon and the two
1. Press the
digits on the DISPLAY begin to flash.
2. Turn the TIMER KNOB towards “+” and “-” to
adjust the hour value.
button again until the other two
3. Press the
digits on the DISPLAY begin to flash.
4. Turn the TIMER KNOB towards “+” and “-” to
adjust the minute value.
button again to confirm.
5. Press the
6. When the set time has elapsed, the text END
appears on the display and a buzzer sounds.
• For example: it is 9:00 a.m. and the Economy
(ECO) FAST CLEAN level has been selected, with
the default duration of 1 hour. 12:30 is scheduled as
the end time. The programme will start automatically
at 11:30 a.m.
and
Programming has been set when the
buttons are illuminated. The display shows the FAST
CLEAN end time and duration alternately.
Once the automatic cleaning cycle is over
You will have to wait until the temperature inside the
oven has cooled down sufficiently before you can
open the oven door. You will notice some white dust
deposits on the bottom and the sides of your oven;
remove these deposits with a damp sponge once
the oven has cooled down completely. Alternatively,
you can make use of the already heated oven, in
which case it is not necessary to remove the
deposits, they are completely harmless and will not
affect your food in any way.
Assistance
/*
Warning:
The appliance is fitted with an automatic diagnostic system which detects any malfunctions. Malfunctions are
displayed by messages of the following type: ”F” followed by numbers.
Call for technical assistance should a malfunction occur.
Never use the services of an unauthorised technician.
Please have the following information to hand:
• The type of problem encountered.
• The appliance model (Mod.).
• The serial number (S/N).
The latter two pieces of information can be found on the data plate located on the appliance.
">