Breville Smart Grinder Pro BCG820 Instruction Booklet

the Smart Grinder™ Pro
Instruction Booklet
Suits all BCG820 models
CONGRATULATIONS
on the purchase of your new
Breville product
2
Contents
3
Breville recommends safety first
9
Know your Breville product
12
Operating your Breville product
20
Care, cleaning & storage
22
Coffee tips
24
Troubleshooting
3
Breville recommends safety first
At Breville we are very safety conscious. We design and manufacture consumer products with
the safety of you, our valued customer, foremost in mind. In addition we ask that you exercise
a degree of care when using any electrical appliance and adhere to the following precautions.
Important safeguards
FOR ALL ELECTRICAL
APPLIANCES
• Remove and safely discard
any packaging material and
promotional labels before
using the Breville Smart
Grinder™ Pro for the first time.
• To eliminate a choking
hazard for young children,
remove and safely discard
the protective cover fitted to
the power plug of the Breville
Smart Grinder™ Pro.
• Do not place the Breville
Smart Grinder™ Pro near
the edge of a bench or table
during operation.
• Do not place the Breville
Smart Grinder™ Pro on or
near a hot gas burner, electric
element or where it could
touch a heated oven.
• Do not operate the Breville
Smart Grinder™ Pro on a sink
drain board.
• Ensure that the surface is
level, clean and free of water.
4
• The Breville Smart Grinder™
Pro is not intended to be
operated by means of an
external timer or separate
remote control system.
• To protect against electric
shock, do not immerse the
grinder base, power cord or
power plug in water or allow
moisture to come in contact
with these parts.
• Always switch the Breville
Smart Grinder™ Pro off at
the power outlet and unplug
if Breville Smart Grinder™
Pro is to be left unattended,
if not in use, before cleaning,
before attempting to move,
disassembling, assembling
and when storing.
• Do not use attachments other
than those provided with the
Breville Smart Grinder™ Pro.
• Do not operate the Breville
Smart Grinder™ Pro without
locking the bean hopper lid in
position. Keep fingers, hands,
hair, clothing and utensils
away from the bean hopper
during operation.
Breville recommends safety first
• The coffee grinder should
not be switched on until the
bean hopper and hopper lid
are locked into position in the
grinding chamber.
• Do not operate the Breville
Smart Grinder™ Pro,
continuously for longer
than 2 minutes as this could
cause overheating. Allow the
Breville Smart Grinder™ Pro
to cool down for 20 minutes
after long operation.
• Do not use the Breville Smart
Grinder™ Pro for any other
purpose than grinding
coffee beans.
• Do not use pre ground coffee
in bean hopper. The Breville
Smart Grinder™ Pro will not
grind food that is sticky, or
extremely hard, or make
pastes of any fruits, seeds or
herbs ie. curry pastes,
nut butters.
• Keep the Breville Smart
Grinder™ Pro and accessories
clean. Follow the Care
and Cleaning instructions
provided on page 20.
• The installation of a residual
current device (safety switch)
is recommended to provide
additional safety protection
when using electrical
appliances. It is advisable
that a safety switch with a
rated current not exceeding
30mA be installed in the
electrical circuit supplying
the appliance. See your
electrician for professional
advice.
• This appliance shall not be
used by children. Keep the
appliance and its cord out of
reach of children.
• Appliances can be used
by persons with reduced
physical, sensory or mental
capabilities or lack of
experience and knowledge
if they have been given
supervision or instruction
concerning use of the
appliance in a safe way and
if they understand the hazards
involved.
• Children should be
supervised to ensure that
they do not play with the
appliance.
5
Breville recommends safety first
IMPORTANT SAFEGUARDS
FOR ALL ELECTRICAL
APPLIANCES
• Unwind the power cord fully
before use.
• Do not let the power cord
hang over the edge of a bench
or table or, touch hot surfaces
or become knotted.
• To protect against electric
shock, do not immerse the
appliance, power cord or
power plug in water or any
other liquid.
• It is recommended to
regularly inspect the
appliance. Do not use the
appliance if the power cord,
power plug or appliance
becomes damaged in any
way. Return the entire
appliance to the nearest
authorised Breville Service
Centre for examination and/
or repair.
• Any maintenance, other than
cleaning, should be performed
at an authorised Breville
Service Centre.
• This appliance is for
household use only. Do
not use this appliance for
anything other than its
intended use. Do not use in
moving vehicles or boats. Do
not use outdoors. Misuse may
cause injury.
• The installation of a residual
current device (safety switch)
is recommended to provide
additional safety protection
when using electrical
appliances. It is advisable that
a safety switch with a rated
residual operating current not
exceeding 30mA be installed
in the electrical circuit
supplying the appliance.
See your electrician for
professional advice.
• The appliance is not intended
to be operated by means of
an external timer or separate
remote control system.
• Connect only to a 220 - 240V
power outlet.
SAVE THESE INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
6
7
8
KNOW
your Breville product
9
KNOW your Breville product
A
B
C
D
I
Oi
Oii
E
F
J
G
K
H
O
L
M
N
10
KNOW your Breville product
A. Bean Hopper Lid
Air tight seal to maximise bean freshness.
B. Bean Hopper
450g bean hopper with locking system for
easy removal and bean transfer.
C. Hardened Stainless Steel Conical Burrs
Maximises particle size for full flavour
potential.
- Removable and Adjustable Upper Burr
D. Backlit LCD Screen
Displays grind setting, grind size, number
of shots or cups and current grind time.
E. GRIND AMOUNT|PROGRAM Dial
Adjusts programmed amount to increase
or decrease dose.
F. SHOTS|CUPS Button
Selects number of shots or cups.
G. Grind Outlet
H. Grind Tray
Catches grind overflow.
Removable for easy cleaning.
I. Grind Size Dial
60 custom grind settings from espresso
to plunger.
J. START|PAUSE|CANCEL Button
Starts, Pauses and Cancels operation.
K. Portafilter Activation Switch
Activates or cancels grinder with a press
of the portafilter.
Accessories
L. Portafilter Cradle 50–54mm
M. Portafilter Cradle 58mm
N. Conical Burr Cleaning Brush
O. Grinds Container
For storing ground coffee.
Oi - Container Cap
Oii - Container Lid
Not Shown
Grinding Chamber
Minimises static of beans
before dispensing.
Automatic Thermal Safety Shut Off
Protects motor from overheating.
Power Saving/Sleep Mode
Unit powers down to standby after
5 minutes of non use.
Cord Storage
OPERATING
your Breville product
12
OPERATING your Breville product
GRINDER OVERVIEW
Your Smart Grinder™ Pro uses Hardened
Stainless Steel Conical Burrs and is able to
grind whole bean coffee suitable for a range of
Brewing Methods, from the finest setting for
Espresso to the coarsest setting for Plunger.
You are able to select the amount of Shots or
Cups with a single button. The Grind Amount
(dose) for all coffee types is controlled by a
digital timer. The default dose for each Brew
Method is able to be adjusted by simply
turning the Grind Amount dial and changing
the time the grinder will run. Once you have
your desired dose, you can press and hold the
PROGRAM button to set your custom time.
You can grind directly into a Portafilter, Grinds
Container or Drip Coffee filter basket.
Before first use
Before first use, remove and safely discard
all promotional labels and packing materials
attached to your Breville product.
Wash hopper, cradles, grind container,
container lid and cleaning brush in warm
soapy water and dry thoroughly. Wipe
exterior of grinder with a soft damp cloth and
dry thoroughly. Place grinder on flat level
surface and plug power cord into 230–240V
outlet and switch Power ‘ON’.
ENERGY SAVING FEATURE
The grinder will automatically switch
off if not used after 5 minutes.
To reactivate the machine whilst in
POWER SAVING/SLEEP MODE, press
any button on the grinder control panel.
ASSEMBLING Your Breville
Smart Grinder™ Pro
Bean Hopper
Align tabs on the base of the bean hopper
and insert hopper into position. Turn the bean
hopper dial 90° to lock into position.
Fill with fresh coffee beans and secure lid on
top of bean hopper.
The bean hopper can be removed by turning
dial anti clockwise and lifting hopper to pull
out. The locking system allows you to remove
and transfer beans in the hopper to a storage
container safely.
Within each Brew Method, Espresso,
Percolator, Filter or Plunger, there is a range of
grind size settings. Between each Brew Method
the grind size settings will differ. This is due to
each method requiring different grind sizes for
optimum extraction.
Experiment with different grind size settings
by rotating the Grind Size dial to achieve the
brew that best suits your taste.
GRIND AMOUNT
SHOTS CUPS
START PAUSE
NOTE
If bean hopper has not been locked
into position, ‘PLEASE LOCK HOPPER’
message will be displayed on the LCD
screen disabling the operation of the
grinder for safety.
PROGRAM
CANCEL
13
OPERATING your Breville product
Grinding for Espresso Coffee
Use single wall filter baskets when grinding
fresh coffee beans. Use the finer 1–30 settings
in the ESPRESSO range.
Step 2:
Selecting your SHOTS|CUPS
Select the desired amount of ground coffee
required by pressing the SHOTS|CUPS button.
GRIND AMOUNT
SHOTS CUPS
START PAUSE
Step 1:
Insert the appropriate Portafilter Cradle size.
Insert your portafilter into the cradle.
CRADLES
50-54mm
58mm
PUSH
NOTE
You can change the amount already
selected during operation by pressing
the SHOTS|CUPS button. Maximum
number of shots with the cradle
inserted is 2.
PROGRAM
CANCEL
Continue pressing the SHOTS|CUPS button
until desired amount is displayed.
The maximum number of shots or cups for
each Brew Method is shown in the Coffee
Chart below. The amount dispensed will vary
depending on the Brew Method selected and
the Grind Amount.
Rotate the Grind Amount dial to adjust the
grinding time to achieve the correct amount of
coffee. Increasing time will increase the dose
and decreasing the time will decrease the dose.
GRIND AMOUNT
SHOTS CUPS
PROGRAM
START PAUSE
CANCEL
COFFEE CHART
BREW METHOD
ESPRESSO
PERCOLATOR
DRIP FILTER
PLUNGER
GRIND SETTING
FINE
MEDIUM
MEDIUM COARSE
COARSE
GRIND SIZE
1-30
31-45
46-54
55-60
AMOUNT
1 UP TO 8 SHOTS
1 UP TO 12 CUPS
1 UP TO 12 CUPS
1 UP TO 12 CUPS
14
OPERATING your Breville product
Step 3:
Grinding into Grinds Container or
Coffee Filter
Select your Grind Size
For espresso, we recommend selecting Grind
Size setting 12 as a starting point and moving
the Grind Size dial Coarser or Finer to adjust
the flow of espresso as required. This should
be done in conjunction with setting the Grind
Amount (dose).
Step 1:
Remove cradle by sliding out from under the
grind outlet.
PULL
GRIND AMOUNT
PROGRAM
SHOTS CUPS
START PAUSE
CANCEL
Slide in Grinds Container with cap open or
Coffee Filter directly under grind outlet.
You will need to extract a shot of espresso to
determine if a change in Grind Size and/or
Grind Amount is necessary to achieve the
correct rate of flow. Traditionally, a single shot
of espresso is defined as ~30ml in 30 seconds
and a double shot of espresso as ~60mls in
30 seconds.
OPEN CONTAINER
CAP
INSERT UNDER
GRIND OUTLET
NOTE
If the Grind Size dial is tight,
run the grinder by pressing the
START|PAUSE|CANCEL button while
turning the Grind Size dial. This will
release coffee grounds caught between
the burrs.
•
Select the required amount of ground
coffee by pressing the SHOTS|CUPS
button.
15
OPERATING your Breville product
•
Press the START|PAUSE|CANCEL
button to start grinding operation.
FEATURES OF YOUR BREVILLE
SMART GRINDER™ PRO
Automatic Grinding
SHOTS CUPS
START PAUSE
Grinding automatically allows you to grind
hands-free. The grinder will automatically
stop when the preset amount of coffee is
dispensed.
•
‘Press & Release’ either the
START|PAUSE|CANCEL button or
push the handle of your portafilter once.
This will activate the PORTAFILTER
SWITCH.
•
Grinding will automatically stop when
the preset amount is dispensed.
CANCEL
SHOTS CUPS
START PAUSE
PUSH
CANCEL
You can grind into Grinds Container without
the lid. However, we recommend keeping the
lid on to prevent coffee grinds from escaping.
OR
START PAUSE
PORTAFILTER SWITCH
PRESS & RELEASE
It is normal for the correct amount of coffee
to appear overfilled in your portafilter. Untamped coffee is approximately three times
the volume of tamped coffee.
NOTE
Programming a custom grind amount/
time sets it for just that Brew Method.
This will not change the other Shots or
Cups settings.
16
OPERATING YOUR BREVILLE PRODUCT
Pause Function
Manual Grinding
You can pause the grinder during operation
allowing you to collapse or settle the coffee in
the portafilter.
Grinding manually allows you to have
complete control over how much coffee is
dispensed.
•
‘Press & Release’ the
START|PAUSE|CANCEL button to start
the grinding operation.
•
•
During grinding, press the
START|PAUSE|CANCEL button again to
pause the operation for 10 seconds.
‘Press & Hold’ either the
START|PAUSE|CANCEL button or push
the handle of your portafilter to activate
the PORTAFILTER SWITCH for as long
as you require.
•
‘Release’ START|PAUSE|CANCEL button
or PORTAFILTER SWITCH and grinding
will stop.
•
Press again within this time to resume
the balance of the dose.
PUSH
OR
GRIND AMOUNT
SHOTS CUPS
START PAUSE
START PAUSE
PORTAFILTER SWITCH
PRESS, HOLD & RELEASE
PROGRAM
CANCEL
PRESS & RELEASE
Program Function
Once you have set your required dose, you
can program this time into the number of
shot(s) currently displayed on the LCD. Press
and hold the PROGRAM button, grinder
will beep twice to confirm. Only the shot
displayed will be programmed, all other shots
will remain unchanged.
GRIND AMOUNT
SHOTS CUPS
PROGRAM
START PAUSE
CANCEL
PRESS & HOLD
17
OPERATING your Breville product
ADJUSTING YOUR GRIND AMOUNT
NOTE
The GRIND AMOUNT dial gives you the
ability to modify the preset SHOTS|CUPS
amounts to deliver more or less ground coffee
into your Portafilter or Grinds Container.
To RESET the grind amount/time to
the default settings, ‘press & hold’ the
SHOTS|CUPS button until a long beep
sounds.
Increasing the Grind Amount
To increase the grind amount selected, turn
the GRIND AMOUNT dial to the right.
Each adjustment will increase the grind time
by 0.2 of a second.
GRIND AMOUNT
SHOTS CUPS
START PAUSE
PROGRAM
CANCEL
Decreasing the Grind Amount
To decrease grind amount selected, turn the
GRIND AMOUNT dial to the left.
Each adjustment will decrease the grind time
by 0.2 of a second.
GRIND AMOUNT
PROGRAM
18
SHOTS CUPS
START PAUSE
CANCEL
OPERATING your Breville product
Adjusting conical burrs
Some types of coffee may require a wider grind range to achieve an ideal extraction or brew.
A feature of your Smart Grinder™ Pro is the ability to extend this range with an adjustable upper
burr. We recommend making only one adjustment at a time.
1
2
3
4
5
6
AIR TIGHT
CONTAINER
Unlock hopper
Hold hopper over container & turn
dial to release beans into container
Align hopper
into position
Run grinder
until empty
Remove hopper
Remove upper
burr
7
8
10
11
12
13
9
FINE
FINE
FINE
FINE
5
4
6
COARS
E
7
8
COAR
SE
COAR
SE
COARS
E
Remove wire
Move adjustable Align the number Insert wire
Push upper burr
handle from both top burr, 1 number, with the handle
handle from both firmly into
sides of the burr coarser or finer
opening
sides of the burr position
14
15
Lock hopper
Check your
extraction
Lock upper burr Align hopper
into position
19
CARE, CLEANING
& STORAGE
20
CARE, CLEANING & STORAGE
CARE, CLEANING & STORAGE
NOTE
1. Empty beans from the hopper and grind
out any excess beans (see below).
Do do not use alkaline or abrasive
cleaning agents, steel wool or scouring
pads, as these can damage the surface.
2. Unplug power cord from power outlet
before cleaning.
3. Wash the grind container and lid, bean
hopper and lid in warm soapy water, rinse
and dry thoroughly.
4. Wipe and polish exterior of appliance
with a soft damp cloth.
NOTE
We recommend you do not clean any
grinder parts or accessories in the
dishwasher.
Cleaning conical burrs
Regular cleaning helps the burrs achieve consistent grinding results which is especially important
when grinding for espresso coffee.
1
2
3
4
5
6
AIR TIGHT
CONTAINER
Unlock hopper
Hold hopper over container & turn Align hopper
dial to release beans into container into position
Run grinder
until empty
Remove hopper Remove upper
burr
7
8
9
10
11
12
Clean upper
burr with
cleaning brush
Clean lower
burr with
cleaning brush
Clean grind
outlet with
brush
Push upper
Lock upper burr Align hopper
burr firmly into
into position
position
13
Lock hopper
21
COFFEE TIPS
22
COFFEE TIPS
Making better quality coffee
PLUNGER COFFEE
•
Follow these easy steps for a great cup:
•
Freshly ground coffee is the key to making
coffee with more flavour and body.
Coffee flavour and strength is a personal
preference. Vary the type of coffee beans,
amount of coffee and fineness of grind to
achieve the flavour you prefer.
1. Using a variable temperature kettle, heat
the appropriate volume of water to 95˚C.
This is an ideal temperature for brewing
coffee. Never using boiling water.
2. Select Grind Size setting 58.
•
Use freshly roasted coffee beans with a
‘roasted on’ date to maximise flavour, not a
use-by or best before date.
3. Select the number of cups you are brewing.
Adjust the amount of coffee to suit the
strength you prefer.
•
Use coffee beans between 5 and 20 days
after the ‘roasted on’ date for optimal
freshness.
4. Place the ground coffee in the plunger
vessel.
•
Store coffee beans in a dark, cool and dry
place. Vacuum seal if possible.
•
Buy in small batches to reduce the storage
time and store no more than one week’s
supply at any time.
•
Once coffee is ground, it quickly loses its
flavour and aroma. For the best results,
grind beans immediately before brewing.
•
Do not store beans in the bean hopper.
Place them back in an airtight container.
•
When storing the appliance, run grinder
empty to clear ground beans left in
chamber.
•
Run grinder for 2 seconds to purge some
coffee before each use, for maximum
freshness.
•
Clean the bean hopper and conical burrs
regularly.
5. Pour the heated water into the plunger in
a swirling manner to ensure all the ground
coffee is soaked & the plunger vessel is full.
The ‘bloom’ (expanding coffee & gases)
should reach the top of the plunger.
6. Using a timer, wait 4 minutes.
7. Using a spoon, break the ‘crust’ (the bloom
becomes dense & a bit hard).
8. Insert the plunger & carefully press down.
9. Do not press too hard. Gently release
pressure by pulling up slightly and press
down again if you have pressed too hard.
23
TROUBLESHOOTING
24
TROUBLESHOOTING
Problem
Possible Cause
What to Do
Grinder does
not start after
pressing START|
PAUSE|CANCEL
button
• Grinder not plugged in.
• Plug power cord into
power outlet.
• Remove power plug from power
outlet. Leave for 20 minutes to cool
down before using again.
• Lock bean hopper into position.
• Grinder has overheated.
• Bean hopper not attached
correctly. ‘PLEASE LOCK
HOPPER’ will be displayed
on LCD screen.
Motor starts but
no ground coffee
coming from
grind outlet
Motor starts but
operates with
a loud ‘racket’
noise
• Incorrect button press.
• No coffee beans in bean
hopper.
• Grinder/bean hopper
is blocked.
• Grinder is blocked
with foreign item or chute
is blocked.
• Moisture clogging grinder.
• Press START|PAUSE|CANCEL
or PORTAFILTER SWITCH
to activate.
• Fill bean hopper with fresh
coffee beans.
• Remove bean hopper. Inspect
bean hopper & burrs for blockage.
Replace parts and try again.
• Remove bean hopper, inspect burrs
& remove any foreign body.
• Clean burrs and chute (refer to
Care & Cleaning on page 20).
• Leave burrs to dry thoroughly
before re-assembling. It is possible
to use a hair dryer to blow air into
grinder inlet (lower burr) to dry.
Unable to lock
bean hopper into
position
• Coffee beans obstructing
bean hopper locking
device.
• Remove bean hopper. Clear coffee
beans from top of burrs. Re-lock
hopper into position & try again.
Not enough/
too much coffee
grind
• Grind amount requires
adjustment.
• Press SHOTS|CUPS button to
change grind amount.
• Use GRIND AMOUNT dial to fine
tune the amount ‘more’ or ‘less’.
Portafilter
overfills
• It is normal for the correct amount
of coffee to appear overfilled in
your portafilter. Untamped coffee
has approximately three times
the volume of tamped coffee.
Emergency stop?
• Press START|PAUSE|CANCEL
button to stop operation.
• Unplug power cord from
power outlet.
25
NOTES
26
NOTES
27
Breville Customer Service Centre
Australian Customers
New Zealand Customers
Mail:
Mail:
PO Box 22
Botany NSW 2019
AUSTRALIA
Private Bag 94411
Botany Manukau 2163
Auckland NEW ZEALAND
Phone: 1300 139 798
Phone: 0800 273 845
Fax:
Fax:
(02) 9384 9601
Email: Customer Service:
[email protected]
0800 288 513
Email: Customer Service:
[email protected]
www.breville.com.au
Breville is a registered trademark of Breville Pty. Ltd. A.B.N. 98 000 092 928.
Copyright Breville Pty. Ltd. 2013.
Due to continued product improvement, the products illustrated/photographed
in this brochure may vary slightly from the actual product.
BCG820 Issue - A13
">