Dimplex Stockbridge Stove
Model: SKG20
Dimensions
(millimetres)
620
Installation and Operating Instructions
08/19238/0 Issue 0
390
640
Fig. 1
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE.
I mportant Safety Advice:
When using electrical appliances, Basic precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons, including the following:
If the appliance is damaged, check with the supplier before installation and operation.
Do not use outdoors.
Do not use in the immediate surroundings of a bath, shower or swimming pool.
Do not locate the heater immediately below a fixed socket outlet or connection box.
Do not cover the heater. Do not place material or garments on the heater, or obstruct the air circulation around the heater, for instance by curtains or furniture, as this could cause overheating and a fire risk.
This appliance is not intended for use by children or other persons without assistance or supervision if their physical, sensory or mental capabilities prevent them from using it safely. Children should be supervised to ensure that they do not play with the appliance.
Do not use this heater in series with a thermal control, a program controller, a timer or any other device that switches on the heat automatically, since a fire risk exists when the heater is accidentally covered or displaced.
Ensure that furniture, curtains or other combustible material are positioned no closer than 1 metre from the heater.
In the event of a fault unplug the heater.
Unplug the heater when not required for long periods.
Although this heater complies with safety standards, we do not recommend its use on deep pile carpets or on long hair type of rugs.
The appliance must be positioned so that the plug is accessible.
If the supply cord is damaged it must be replaced by the manufacturer or service agent or a similarly qualified person in order to avoid a hazard.
Keep the supply cord away from the front of the heater.
Introduction
These fires incorporate a flame effect, which can be used with or without heating, so that the comforting effect may be enjoyed at any time of the year. The flame effect is provided by a low wattage motor and two 60 watt lamps. Using the flame effect on its own, therefore, requires little electricity.
The manual controls are located behind the firebox doors.
The remote control is packed separately in the carton. A
Choice of 1kw or 2kw thermostatically controlled heat output is provided by the fan heater, which is concealed beneath the unit.
These models are designed to be free standing and are normally positioned against a wall.
Please note: Used in an environment where background noise is very low, it may be possible to hear the motor which operates the flame effect. This is normal and should not be a cause for concern.
Electrical connection
WARNING – THIS APPLIANCE MUST BE EARTHED
This heater must be used on an AC ~ supply only and the voltage marked on the heater must correspond to the supply voltage.
Before switching on, please read the safety warnings and operating instructions.
For your convenience, the heater is fitted with a rewireable plug incorporating a 13 amp fuse. In the event of replacing the fuse in the plug supplied, a 13 amp fuse approved by
ASTA to BS1362 must be used.
Operation
The controls are located behind the doors (see Fig. 2).
Connect the fire to your electricity supply.
Remote Control
Warning: it takes time for the receiver to respond to the transmitter. Do not press the buttons more than once within two seconds for correct operation.
On
Button
Off
Button
Increase
Brightness
Decrease
Brightness controls
Fig. 2
Note: When either the remote control or the manual controls are used, the neon’s will come on for 3 seconds indicating the relevant setting (see fig. 3).
Battery information
neon’s for indicating the operation level
Fig. 3
OFF
ON
Manual
Controls
Standby
Switch Note : The Standby
Switch must first be turned on to operate either the manual or the remote controls.
Fig. 5
Manual or Remote Operation
Setting
Flame effect
Flame effect & 1kW heat
Operation
Press the ‘ON’ button once
Press the ‘ON’ button again
Indication
Bottom Neon
Bottom &
Middle Neon
All 3 Neon’s Flame effect & 2kW heat Press the ‘ON’ button again
To turn off any of the settings
Press the ‘OFF’ button once
To increase or decrease the brightness of the fuel effect use the buttons as shown in Fig. 5
Batteries
Fig. 4
1.
2.
3.
Slide open the battery cover on the back of the remote control
Install three AAA batteries into the remote control (see
Fig. 4)
Replace the battery cover.
Discard leaky batteries
Dispose of batteries in the proper manner according to
Provincial and local regulations. Any battery may leak electrolyte if mixed with a different battery type, if inserted incorrectly, if all the batteries are not replaced at the same time, if disposed of in a fire or if an attempt is made to charge a battery not intended to be recharged.
Thermal Safety Cut-out
A thermal safety cut-out is incorporated in the heater to prevent damage due to overheating.
This can happen if the heat outlet was restricted in any way.
The heater will switch on once the obstruction has been removed and the heater has cooled. If the cut-out continues to operate intermittently, the heater should be switched off and a service agent contacted.
Maintenance
WARNING: ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE.
Instructions for fitting Coal Option
Introduction
Your fire is provided with a coal effect option. To fit simply follow the instructions given below.
Removal of Log Effect
Remove the three screws securing the log effect assembly.
Remove the fret and slide out the log effect assy ( see Fig. 6).
Fig. 6
Fitting Coal Effect
Fit the coal effect (flat fuel bed) and fret in position and secure with the three screws (see Fig. 7)
Place the coal lumps on the fuel bed. A plastic glove is provided for handling the coal.
Note: The log effect should be stored away for possible future use.
Fig. 7
Lamp Replacement
To gain access to the lamps remove the coal/log effect from the fire by unscrewing the three fixing screws from the fuel bed and sliding out the fuel effect.
Unscrew any defective lamps (see Fig. 8) and replace with a
240V, 60 Watt E14 SES clear candle lamp.
Do not overtighten.
Fig. 8
Cleaning
Before commencing cleaning, unplug the heater and allow it to cool.
The surfaces of the heater should be given an occasional wipe over with a soft damp cloth. Do not use detergents, abrasive cleaning powder or polish on the body of the heater.
The viewing screens should be cleaned carefully with a chamois leather.
DO NOT use proprietory glass cleaners.
To remove any accumulation of dust or fluff the soft brush attachment of a vacuum cleaner should occasionally be used to clean the outlet grille of the fan heater.
After Sales Service
Your product is guaranteed for one year from the date of purchase.
Within this period, we undertake to repair or exchange this product free of charge (excluding lamps & subject to availability) provided it has been installed and operated in accordance with these instructions.
Your rights under this guarantee are additional to your statutory rights, which in turn are not affected by this guarantee.
Should you require after sales service you should contact our customer services help desk on 0870 727 0101. It would assist us if you can quote the model number, series, date of purchase, and nature of the fault at the time of your call. The customer services help desk will also be able to advise you should you need to purchase any spares.
Please do not return a faulty product to us in the first instance as this may result in loss or damage and delay in providing you with a satisfactory service.
Please retain your receipt as proof of purchase.
The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility
(EMC) EN55014, EN60555-2 and EN60555-3 which cover the essential requirements of EEC Directives 73/23 and 89/336
Glen Dimplex UK Limited
Millbrook House
Grange Drive
Hedge End
Southampton
Hampshire. SO30 2DF
UK customer help line (8.00AM – 6.00PM Mon-Fri; 8.30AM-1.00PM Sat)
Customer Services: Tel.
Fax.
Republic of Ireland
e-mail
Tel.
0870 7270101
0870 7270102 [email protected]
01 8424833
[c] Glen Dimplex UK Limited
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Glen Dimplex UK Limited.
